Nitoflor FC110.pdf
-
Upload
riverwilliams -
Category
Documents
-
view
275 -
download
1
Transcript of Nitoflor FC110.pdf
Nito
flor®
FC
110
constructive solutionsNitoflor® FC110
Polyurethane floor coating and sealer
Uses
As a clear, sealing coat on cementitious floors to provide adust proof and easily cleaned surface with resistance topenetration of oils and liquids, ideal for warehouses, garages,indoor car parks, light industries etc.
Advantages
Easily laid - Simple brush application
Durability - Good resistance to abrasion Improves scratchresistance of the floor surface.
Non-dusting- totally seals the concrete surface preventingdusting
Description
Nitoflor FC110 is a two part, polyurethane system. It hasexcellent adhesion to cementitious surfaces and when cured,forms a semigloss flexible film. It penetrates the surface tobind together the particles to produce a hardwearing andimpermeable surface. It is supplied in two parts and requiresmixing on site.
Technical support
Fosroc offers technical support service to specifiers, endusers and contractors, as well as onsite technical assistancein locations all over the country.
Properties
Cure timeTack free 1 hour at 300C.Open to light foot traffic 24 hours at 300C.
Full cure 7 days.
Pot life Once both components aremixed, the mixed materialshould be used within 60 mins.at 300C.
Application instructions
Preparation
Substrate must be clean and free from all contamination andin dry condition. All loose material should be swept away andexcess laitence removed by using Reebaklens, cleaning andetching agent. Surface should then be washed off thoroughlyand allowed to dry completely.
Coating
Mix both the components as supplied in a plastic container orbucket with a paddle attached to a slow speed drillingmachine. Using a soft brush, or roller apply the mixed materialto the surface, until an even coverage is obtained. Two coatsare normally recommended and a minimum drying time of 1- 2 hours should be allowed between coats. On sand/cementscreeds, 3 to 4 coats may be required depending on porosity.Where two or more coats are applied best results are obtainedby not allowing more than 24 hours between applications.
Limitations
Nitoflor FC110 cannot be applied below 150C or above400C.
It is not recommended for applications directly exposedto sunlight.
It is not suitable for applications on substrates appliedwith plaster of paris.
Estimating
Packaging and coverage
Nitoflor FC110 is supplied in 1 Ltr. (component A -0.5 Ltr +component B - 0.5 Ltr) and 5 Ltr (2.5 Ltr + 2.5 Ltr) packings.Coverage of the first coat of Nitoflor FC110 on concretedepends to a great extent on surface texture and porosity.Second and subsequent coats show improved coverage.
For estimation purposes, a coverage of 6 m2 per litre, per coatcan be considered.
Storage
Nitoflor FC110 should be stored in accordance with thestatutory regulations with regard to highly flammable liquidsand gases.
Shelf life
6 months in unopened containers at 300C.
Nitoflor® FC110
INDIA/2004/0604/D
Important note :Fosroc products are guaranteed against defective materials and manufacture and are sold subjectto its standard terms and conditions of sale, copies of which may be obtained on request. WhilstFosroc endeavours to ensure that any advice, recommendation specification or information it maygive is accurate and correct, it cannot, because it has no direct or continuous control over whereor how its products are applied, accept any liability either directly or indirectly arising from theuse of its products whether or not in accordance with any advice, specification, recommendationor information given by it.
telephone fax e-mail
++91 80-22240018/120 ++91 80-22233474 [email protected]
Fosroc Chemicals (India) Pvt. Ltd.Head Office111/3, Hafeeza Chamber II Floor,K H Road, PBNo. 2744, Bangalore 560027www.fosroc.com
® Denotes the trademark of Fosroc International Limited
Regional OfficesBangalore Mumbai Delhi KolkataShankar House, IV Floor 208/209, Persepolis First floor,1/2 East Patel Nagar 30/B Jodhpur Park1 & 18, RMV Extension Sector 17, Vashi Opp: Vivek Cinema, Main Patel Rd Ground FloorBangalore 560 080 Navi Mumbai 400 703 New Delhi 110 008 Kolkata 700 068Ph:080-2361 3161/2361 2004 Ph:022-2789 6412/14 Ph:011-25884903/4 Ph: 033 2472 5482Fax : 080-2361 7454 Fax: 022 - 2789 6413 Fax: 011- 25884422 Fax: 033-2472 9921email: [email protected] email:[email protected] email:[email protected] email:[email protected]
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bhubaneshwar : (0674) 2521176 Chennai (044) 24899949/24853383Chandigarh : (0172) 2639360 Cochin : (0484) 2356668 Coimbatore : (0422) 2472966 Goa : (0832) 2542465 Guwahati (0361) 2548793Hyderabad : (040) 27662324/27662425 Hubli (0836) 3402597 Indore : (0731) 504339/5061477 Jaipur : (0141) 2235349 Lucknow :(0522)
22239044 Nagercoil (04652) 2224849 Mangalore: (0824) 22272234 Visakhapatnam : (0891) 2564850
Precautions
Health & Safety
Gloves should be used when handling. If contact with skinoccurs, it must be washed with detergent and water. Solventshould not be used. The use of goggles is recommended.Direct contact with eyes will cause irritation and may causeserious damage if left untreated. Any eye contaminationshould be washed thoroughly with plenty of water andimmediate medical treatment sought.
Fire
Nitoflor FC110 is flammable. Adequate ventilation should beensured during application. Smoking, presence of a nakedflame is strictly prohibited.
Additional information
The Fosroc range of associated products includes highstrength cementitious grouts, epoxy grout, polyester resinbased mortar for rapid presetting of steel shims to level or fordirect bedding of small base plates; Resin anchoringsystems for same day anchoring of bolts in drilled holes inconcrete or rock. Also available a range of products for use inconstruction; viz, admixtures, curing compounds, releaseagents, flooring systems and repair mortars.
Separate data sheets are available on these products