Nissan Terrano 93-06Nissan Terrano 1993 - 2006 PSB 151 Front Upper Control Arm Bushing OE Number:...
1
REAR Installation Instructions: Nissan Terrano 1993 - 2006 PSB 151 Front Upper Control Arm Bushing OE Number: 5450641G00 / 5504641G00 1. Remove original bushing by pressing out or using a blow torch. 2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel 3. Clean housing with sand paper to remove sharp edges, so as not to damage new bushing. 4. Remove metal sleeve from new poly bushing. 5. Lubricate inner part of the bushing with multi-purpose grease. 6. Tap poly bushing into housing with a rubber mallet. 7. Tap metal sleeve into poly bushing. 8. Installation is complete. PSB 455 (96 - 04) Front Anti Roll / Sway Bar Bushing - 27mm OE Number : 54613-4P007 1. Remove metal bracket of original rubber bushing. 2. Remove old rubber bushing and clean bar. 3. Find slit on new poly bushing and slide over the bar. 4. Refit metal bracket. 5. The installation is complete. PSB 594 Rear Upper or Lower Arm Bushing OE Number: 5504541G00 / 5504641G00 1. Remove original bushing by pressing out or using a blow torch. 2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel. 3. Clean housing with sand paper to remove sharp edges, so as not to damage new bushing. 4. Remove metal sleeve from new poly bushing. 5. Lubricate inside and outside of poly bushing with multi purpose grease.. 6. Press two bushing halves into housing. (Rubber hammer or by hand) 7. Insert metal sleeve into bushings. 8. The installation is complete. PSB 456 (96 - 04) (Installation instructions same as PSB 455) Rear Anti Roll / Sway Bar Bushing - 16mm OE Number : 56243-1W216 PSB 594 PSB 594 PSB 455 PSB 456 PSB 151 FRONT
Transcript of Nissan Terrano 93-06Nissan Terrano 1993 - 2006 PSB 151 Front Upper Control Arm Bushing OE Number:...
REAR
Installation Instructions:Nissan Terrano1993 - 2006PSB 151Front Upper Control Arm BushingOE Number: 5450641G00 / 5504641G001. Remove original bushing by pressing out or using a blow torch. 2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel3. Clean housing with sand paper to remove sharp edges, so as not to damage new bushing.4. Remove metal sleeve from new poly bushing.5. Lubricate inner part of the bushing with multi-purpose grease.6. Tap poly bushing into housing with a rubber mallet.7. Tap metal sleeve into poly bushing.8. Installation is complete.
PSB 455 (96 - 04)Front Anti Roll / Sway Bar Bushing - 27mmOE Number : 54613-4P0071. Remove metal bracket of original rubber bushing.2. Remove old rubber bushing and clean bar.3. Find slit on new poly bushing and slide over the bar.4. Refit metal bracket.5. The installation is complete.
PSB 594Rear Upper or Lower Arm BushingOE Number: 5504541G00 / 5504641G001. Remove original bushing by pressing out or using a blow torch. 2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.3. Clean housing with sand paper to remove sharp edges, so as not to damage new bushing.4. Remove metal sleeve from new poly bushing.5. Lubricate inside and outside of poly bushing with multi purpose grease..6. Press two bushing halves into housing. (Rubber hammer or by hand)7. Insert metal sleeve into bushings.8. The installation is complete.
PSB 456 (96 - 04)(Installation instructions same as PSB 455)Rear Anti Roll / Sway Bar Bushing - 16mmOE Number : 56243-1W216
PSB 594
PSB 594
PSB 455
PSB 456
PSB 151
FRONT
