NINGBO KYLIN MACHINERY CO., LTD. -...

Ball Joints, Angle Joints, Axial Joints, Ball Studs, & Ball Sockets

Rod Ends & Rod Ends for Hydraulic Components

Clevises

NINGBO KYLIN MACHINERY CO., LTD.

Address: Jia Village Industry, Yunlong Town, Yinzhou District, Ningbo, Zhejiang, China.

Telephone: +86 134 56162828

Email: [email protected]

Contact person: Mr. Jack Huang

http://www.ball-joints.com


http://www.ball-joints.com Copyright 2010 Kylin Printed in China Made By Kylin

INDEX

BALL JOINTS ES SERIES 3

BALL JOINTS QI SERIES 4

BALL JOINTS QD SERIES 5

BALL JOINTS PI SERIES 6

BALL JOINTS SQ SERIES 7

BALL JOINTS SQZ SERIES 8

BALL JOINTS BL SERIES 9

BALL JOINTS LHSA SERIES 10

ANGLE JOINTS DIN 71802 11

AXIAL JOINTS AJ SERIES, SIMILAR TO DIN 71802 12

BALL STUDS DIN 71803 13

BALL SOCKETS DIN 71805 14

ROD ENDS PHS SERIES 15

ROD ENDS POS SERIES 16

ROD ENDS SI..T/K SERIES 17

ROD ENDS SA..T/K SERIES 18

ROD ENDS FOR HYDRAULIC COMPONENTS GK..DO SERIES 19

ROD ENDS FOR HYDRAULIC COMPONENTS GF..DO SERIES 20

ROD ENDS FOR HYDRAULIC COMPONENTS GF..LO SERIES 21

ROD ENDS FOR HYDRAULIC COMPONENTS GIHR..DO SERIES 22

ROD ENDS FOR HYDRAULIC COMPONENTS GIHR-K..DO SERIES 23

ROD ENDS FOR HYDRAULIC COMPONENTS GIHN-K..LO SERIES 24

CLEVISES DIN 71752/ISO 8140 G SERIES 25

CLEVISES WITH MALE THREAD GM SERIES 27



Ball Joints ES series

Part # d1 d2 d3 L1 L2 L3 L4 L5 S J Min. Pull Test (lb)

Min. Shear

(lb) ES187 10-32-2B 10-32-2A 0.375 0.438 0.438 0.438 0.875 1.063 0.313 0.313 500 400 ES250 1/4-28-2B 1/4-28-2A 0.438 0.563 0.469 0.500 0.969 1.219 0.375 0.375 750 500 ES312 5/16-24-2B 5/16-24-2A 0.500 0.688 0.531 0.563 1.125 1.406 0.438 0.438 1000 900 ES375 3/8-24-2B 3/8-24-2A 0.625 0.875 0.688 0.750 1.375 1.688 0.500 0.500 1500 1200 ES438 7/16-20-2B 7/16-20-2A 0.750 1.125 0.875 1.000 1.938 2.375 0.625 0.625 2000 2400 ES500 1/2-20-2B 1/2-20-2A 0.750 1.125 0.875 1.000 1.938 2.375 0.625 0.625 2000 2500

- Material: 1) Housing: Carbon Steel 1045; Ball stud: Carbon Steel 1045; Sealing cap: Rubber 2) Alternative: Stainless Steel

- Surface protection: Electroplated galvanized, passivated in white-blue or yellow - Filled with lubricant and circle swing agilely without any blocked - Unless otherwise specified, all dimensions are in inches



Ball Joints QI series

Part # D1 D2 A C F G J L M N P S Min. Pull Test (lb)

Min. Shear

(lb) QI187 10-32-2B 10-32-2A 0.125 0.063 0.438 0.438 0.313 0.438 1.094 0.906 0.438 0.250 430 500 QI250 1/4-28-2B 1/4-28-2A 0.125 0.063 0.469 0.562 0.375 0.562 1.250 0.969 0.531 0.350 560 500 QI312 5/16-24-2B 5/16-24-2A 0.156 0.094 0.531 0.687 0.437 0.625 1.453 1.125 0.605 0.438 1000 1500 QI375 3/8-24-2B 3/8-24-2A 0.187 0.094 0.687 0.875 0.500 0.750 1.750 1.375 0.812 0.470 1580 2400 QI500 1/2-20-2B 1/2-20-2A 0.250 0.094 0.875 1.125 0.625 1.000 2.530 2.030 1.000 0.570 2400 2700

- Material: 1) Housing: Carbon Steel 1045; Ball stud: Carbon Steel 1045; Shell: Carbon Steel 1020; Spring: Stainless Steel 2) Alternative: Stainless Steel




Ball Joints QD series

Part # D1 D2 A C F G J L M N P Min. Pull Test lb

Min. Shear lb

QD187 10-32-2B 10-32-2A 0.125 0.063 0.438 0.438 0.313 0.438 1.094 0.906 0.438 430 650 QD250 1/4-28-2B 1/4-28-2A 0.125 0.063 0.469 0.562 0.375 0.562 1.250 0.969 0.531 950 800 QD312 5/16-24-2B 5/16-24-2A 0.156 0.094 0.531 0.687 0.437 0.625 1.453 1.125 0.605 1000 1000 QD375 3/8-24-2B 3/8-24-2A 0.187 0.094 0.687 0.875 0.500 0.750 1.750 1.375 0.812 1250 1250 QD500 1/2-20-2B 1/2-20-2A 0.250 0.094 0.875 1.125 0.625 1.000 2.530 2.030 1.000 1900 2000

- Material: 1) Housing: Carbon Steel 1045; Ball stud: Carbon Steel 1045; Shell: Carbon Steel 1020; Spring: Stainless Steel 2) Alternative: Stainless Steel




Ball Joints PI series

Part # D1 D2 F G J L M N P

PI3-3 10-32-2B 10-32-2A 0.4380 0.4380 0.3125 0.3125 1.1560 0.8750 0.4840 PI3-4 10-32-2B 10-32-2A 0.4380 0.5630 0.3125 0.3125 1.1560 0.8750 0.4840 PI4-3 1/4-28-2B 1/4-28-2A 0.4380 0.4380 0.3125 0.3125 1.2500 0.9690 0.5310 PI4-4 1/4-28-2B 1/4-28-2A 0.4380 0.5630 0.3125 0.3125 1.2500 0.9690 0.5310

PI4L-4L 1/4-28-2B 1/4-28-2A 0.5620 0.5000 0.3125 0.3400 1.7500 1.5000 1.1200

- Material: 1) Housing: Low Carbon Steel 1020; Ball stud: Low Carbon Steel 1020; Retaining Clip: Spring Steel 2) Alternative: Stainless Steel




Ball Joints SQ series

Static load Yield Part # L D M Thread S1 L1 l L2 d1 D2 W d2 M1 M2 l1 d4 Da

capacity kN strength kNSQ5D 35 16 29 M5X0.8 27 14 4 9 11 9 5 21 10 8 9 11.1 9.22 2.25 SQ6D 40 19 36 M6X1 30 14 5 10 13 11 6 26 11 11 10 12.7 12.1 3.53 SQ8D 48 23 43 M8X1.25 36 17 5 13 16 14 8 31 14 12 12 15.9 19.1 6.57

SQ10D 57 27 51 M10X1.25 43 21 7 15 19 17 10 37 17 15 14 19.1 27.5 10.7 SQ10BD 57 27 57 M10X1.5 43 21 7 15 19 17 10 43 17 21 14 19.1 27.5 10.7 SQ12D 66 31 58 M12X1.25 50 25 7 18 22 19 12 42 19 17 19 22.2 37.5 16.4

SQ12BD 66 31 65 M12X1.75 50 25 7 18 22 19 12 49 19 24 19 22.2 37.5 16.4 SQ14D 75 35 74 M14X1.5 57 26 8 20 25 22 14 56 22 22 19 25.4 48.9 19.8

SQ14BD 75 35 80 M14X2 57 26 8 20 25 22 14 62 22 28 19 25.4 48.9 19.8 SQ16D 84 39 80 M16X1.5 64 32 8 22 27 22 16 60 24 23 22 25.4 48.9 26.9

SQ16BD 84 39 86 M16X2 64 32 8 22 27 22 16 66 24 29 22 25.4 48.9 26.9 SQ18D 93 44 90 M18X1.5 71 34 10 25 31 27 18 68 27 25 23 28.6 61.9 33.3 SQ20D 99 44 90 M20X1.5 77 35 10 28 34 30 20 68 27 25 29 28.6 61.9 45.9 SQ22D ## 50 95 M22X1.5 84 41 12 30 37 32 22 70 28 26 27 31.8 75.4 48

- All dimensions are in mm - Material:

Housing: High strength zinc alloy; Ball: Bearing steel GCr15, equivalent to steel SAE 52100; Shank: Alloy steel 40Cr; Dust Cover: NBR rubber;

- Left hand thread, please add suffix “L”, e.g. SQL16D - Grease is seals in the boot, high wear resistance - Work Temperature: -40°C-120°C



Ball Joints SQZ series

Load ratings Weight Part # d d1 d2 d3 l1 l2 S1 L L1 L2 L3 D1 D2 D3 S2 a

kN kg SQZ5RS 5 M5x0.8 9 20 8 11 7 46 24 4 12 9 11 17 9 15 2.8 0.025 SQZ6RS 6 M6x1.0 10 20 11 12.2 8 55.2 28 5 15 10 13 20 11 15 3.7 0.041 SQZ8RS 8 M8x1.25 12 24 12 16 10 65 32 5 16 12.5 16 24 14 15 5.8 0.075

SQZ10RS 10 M10x1.25 14 30 15 19.5 11 74.5 35 6.5 18 15 19 28 17 15 8.4 0.12 SQZ10RS-1 10 M10x1.5 14 30 21 19.5 11 80.5 35 6.5 18 15 19 28 17 15 8.4 0.12 SQZ12RS 12 M12x1.25 17 32 17 21 15 84 40 6.5 20 17.5 22 32 19 15 11 0.18

SQZ12RS-1 12 M12x1.75 17 32 24 21 15 91 40 6.5 20 17.5 22 32 19 15 11 0.18 SQZ14RS 14 M14x1.5 19 38 22 23.5 17 103 45 8 25 20 25 36 22 11 15 0.27

SQZ14RS-1 14 M14x2.0 19 38 28 23.5 17 109 45 8 25 20 25 36 22 11 15 0.27 SQZ16RS 16 M16x1.5 22 44 23 25.5 19 112 50 8 27 22 27 40 22 11 15 0.36

SQZ16RS-1 16 M16x2.0 22 44 29 25.5 19 118 50 8 27 22 27 40 22 11 15 0.36 SQZ18RS 18 M18x1.5 23 45 25 31 20 130.5 58 10 32 25 31 45 27 11 19 0.54 SQZ20RS 20 M20x1.5 27 50 25 29 24 133 63 10 38 27.5 34 45 30 7.5 19 0.57 SQZ22RS 22 M22x1.5 27 52 26 33 24 145 70 12 43 30 37 50 32 7.5 23 0.76



- Left hand thread, please add suffix “L”, e.g. SQZ16LRS - Grease is seals in the boot, high wear resistance - Work Temperature: -40°C-120°C



Ball Joints BL series

Part # Dimensions mm Static load Capability

kN

Yield strength

kN

Weight g

D1 D2 D3 L1 L2 L3 L4 L5 L6 H W J SΦ

BLM6×1 M6×1 M6×1 10 11 11 26 16 30 38 5 11 10 11.1 9.9 3.92 26 BLM8×1.25 M8×1.25 M8×1.25 13 12 14 31 19 36 45.5 6 14 12 12.7 12.5 6.57 49 BLM10×1.25 M10×1.25 M10×1.25 14.5 15 17 37 23 43 55.5 7 17 14 15.9 18.3 11.3 87 BLM10×1.5 M10×1.5 M10×1.5 14.5 21 17 43 23 43 55.5 7 17 14 15.9 18.3 11.3 90 BLM12×1.25 M12×1.25 M12×1.25 17.5 17 19 42 26 50 64.5 8 19 17 19.1 26.7 16.4 143

BLM12×1.75 M12×1.75 M12×1.75 17.5 24 19 49 26 50 64.5 8 19 17 19.1 26.7 16.4 148 BLM16×1.5 M16×1.5 M16×1.5 22 23 23.5 60 34 64 83 11 24 22 22.2 36.4 26.9 315 BLM16×2 M16×2 M16×2 22 29 23.5 66 34 64 83 11 24 22 22.2 36.4 26.9 325



- Left hand thread, please add suffix “L”, e.g. BLM10X1.5L - Grease is seals in the boot, high wear resistance - Work Temperature: -40°C-120°C



Ball Joints LHSA series

Part # M L L1 L2 l2 l3 W D1 h a

LHSA5-RS M5X0.75 38.5 30 16 12 10 10 10 5 17 LHSA6-RS M6X1.0 38.5 30 16 12 10 10 10 5 17 LHSA8-RS M8X1.25 48 36 19 14.5 12.5 13 13 5 18 LHSA10-RS M10X1.25 57 43 23 16 17 15 15 6.5 19 LHSA12-RS M12X1.75 67 50 27 20 20 17.5 17.5 6.5 20 LHSA14-RS M14X2.0 76 57 30 22.5 22 20 20 8 20 LHSA16-RS M16X1.5 84 64 32 36.5 23 22 22 8 20 LHSA18-RS M18X1.5 93 71 34 41.5 25 25 25 10 20 LHSA20-RS M20X1.5 99 77 35 41 25 28 28 10 20 LHSA22-RS M22X1.5 109 84 41 42 26 30 30 12 20



- Left hand thread, please add suffix “L”, e.g. LHSA5-RSL - Grease is seals in the boot, high wear resistance - Work Temperature: -40°C-120°C



Angle Joints DIN 71802

Weight Dimensions mm

Kg/1000pcs for type

d1 d2 I2 I3 e d5 I1 a SW A and AS h9 ±0.3 ±0.3 Min. h11 ±0.2 ±0.3 h14 C and CS

B and BS

4 12.9 8 M5 10.2 9 10.2 5

7.5 22 7 15.2

13.4 4.5 21.3

10 M6 12.5 11 11.5 6 8

25 8 25.2 22.0

5 43.1 13 M8 16.5 13 14 8

10 30 11 53.1

45.0 M10 6 82.3

16 M12

20 16 15.5 10 13

35 13 103.8 86.6

M14x1.5

M14x2 12 181.0

19 M16

28 20 21.5 14 18

45 16 220.9 188.7

- All dimensions are in mm - Notes:

1) A, B, C type without safety clip on the ball socket. AS, BS, CS type with safety clip on the ball socket

2) Left-hand thread in the ball socket possible 3) Spanner surface for type C and CS on the ball stud 4) The manufacturer reserves the right to supply the ball socket with or without spanner surface 5) With or without sealing caps upon request

- Material: 1) Ball stud: Carbon Steel 1045: Housing: Carbon Steel 1020; Clip: Spring Steel 2) Alternative for all angle joint versions: Stainless Steel 304

- Surface protection: Electroplated galvanized, passivated in white-blue or yellow



Axial Joints AJ series, similar to DIN 71802

Extraction force Weight Part # d1 d2 a la l3 e

F in N Kg AJ8 8 M5 22 19.2 9 10.2 30 0.015 AJ10 10 M6 25 23.5 11 11.5 40 0.025 AJ13 13 M8 30 29.5 13 14 60 0.053 AJ16 16 M10 35 36 16 15.5 80 0.104 AJ19 19 M14x1.5 45 48 20 21.5 100 0.221


1) Left-hand thread in the ball socket possible 2) The manufacturer reserves the right to supply the ball socket with or without spanner surface 3) With or without sealing caps upon request

- Material: 1) Ball stud: Carbon Steel 1045: Housing: Carbon Steel 1020; Clip: Spring Steel 2) Alternative for all angle joint versions: Stainless Steel 304




Ball Studs DIN 71803

Dimensions mm Weight

d1 d2 l1 c d3 d5 d6 l2 l3 l4 l5 SW Kg/1000pcs h9 ±0.2 +0.4 h14 h11 -0.4 ±0.3 ±0.3 ±0.3 max. h14 A and C B

4.0 3.9 8 M5

7.5 2 8 5 3 10.2 9 12.5 4 7 4.55

4.4 4.5 7.1

10 M6 8.0

2.2 10 6 4 12.5 11 15.5 4 8 8.5 7.8

5.0 14.2 13 M8

10.0 2.4 13 8 6 16.5 13 18.5 5.3 11 17.7

16.0 M10 6.0 23.5

16 M12 13.0

2.7 16 10 8 20 16 23 7.3 13 35.1 29.6

M14x1.5 M14x2

12.0 56.2 19

M16 18.0 3 19 14 10 28 20 28.5 10.8 16 71.2

63.7


1) Carbon Steel 1045 2) Alternative for all angle joint versions: Stainless Steel 304

- Ball d1 hardness: Min. HRC52: Hardening depth: Min. 1mm - Surface protection: Electroplated galvanized, passivated in white-blue or yellow



Ball Sockets DIN 71805

a d3 d4 e l1 l2 Weight ±0.3 ±0.5 ±0.5 min. max. ±0.4 Kg/1000pcs for type d1 d2

A B 8 M5 22 8 12.8 10.2 15 6.3 9 8.8

10 M6 25 10 14.8 11.5 17 7 14.2 14.1 13 M8 30 13 19.3 14 20 9.1 29 28.8

M10 16

M12 35 16 24 15.5 22 11.4 57 56.8

M14x1.5 M14x2 19 M16

45 22 30 21.5 28 12.5 125 124.8


1) The manufacturer reserves the right to supply the ball socket with or without spanner surface - Material:

1) Carbon Steel 1020 2) Alternative for all angle joint versions: Stainless Steel 304




Rod Ends PHS series

Part # Dimensions mm Load

ratings kNWeight

kg

d d3 B C1 L3 W d2 d1 h1 L4 L5 d4 d5 dk a dyn. stat.

6H min ≈ C C0

PHS5 5 M5x0.8 8 6 10 9 16 7.7 27 35 4 8.5 11 11.11 13 3.25 5.7 0.016PHS6 6 M6x1.0 9 6.75 12 11 18 8.96 30 39 5 10 13 12.7 13 4.3 7.2 0.022PHS8 8 M8x1.25 12 9 16 14 22 10.4 36 47 5 12.5 16 15.875 14 7.2 11.6 0.047

PHS10 10 M10x1.5 14 10.5 20 17 26 12.9 43 56 6.5 15 19 19.05 13 10 14.5 0.077PHS10-1 10 M10x1.25 14 10.5 20 17 26 12.9 43 56 6.5 15 19 19.05 13 10 14.5 0.077PHS12 12 M12x1.75 16 12 22 19 30 15.4 50 65 6.5 17.5 22 22.225 13 13.4 17 0.1

PHS12-1 12 M12x1.25 16 12 22 19 30 15.4 50 65 6.5 17.5 22 22.225 13 13.4 17 0.1 PHS14 14 M14x2.0 19 13.5 25 22 34 16.9 57 74 8 20 25 25.4 16 17 24 0.16

PHS14-1 14 M14x1.5 19 13.5 25 22 34 16.9 57 74 8 20 25 25.4 16 17 24 0.16 PHS16 16 M16x2.0 21 15 28 22 40 19.4 64 84 8 22 27 28.575 15 21.6 28.5 0.22

PHS16-1 16 M16x1.5 21 15 28 22 40 19.4 64 84 8 22 27 28.575 15 21.6 28.5 0.22 PHS18 18 M18x1.5 23 16.5 32 27 44 21.9 71 93 10 25 31 31.75 15 26 42.5 0.32 PHS20 20 M20x1.5 25 18 33 30 50 24.4 77 102 10 27.5 34 34.925 14 21.5 42.5 0.42 PHS22 22 M22x1.5 28 20 37 32 54 25.8 84 111 12 30 38 38.1 15 38 57 0.54 PHS25 25 M24x2.0 31 22 42 36 60 29.6 94 124 12 33.5 42 42.85 15 47.5 68 0.73 PHS28 28 M27x2.0 35 24 48 41 66 32.3 103 136 14 37.5 46 47.6 15 58 75 0.98 PHS30 30 M30x2.0 37 25 51 41 70 34.8 110 145 15 40 50 50.8 17 64 88 1.1

- All dimensions are in mm - Rod body with right or left-hand female thread. - Outer race lined with bronze liner. - Surface of rod body zinc plated, rod body with a lubricating hole or grease nipple. - For left-hand thread, please add suffix “L”. e.g. PHSL8.



Rod Ends POS series

Load ratings Weight Part # Dimensions mm

kN kg

d d3 B C1 L1 d1 d2 h L2 dk R1s a dyn. stat.

6g min. ≈ C C0

POS5 5 M5x0.8 8 6 20 7.7 16 33 41 11.11 0.3 13 3.25 5.7 0.013POS6 6 M6x1.0 9 6.75 22 8.96 18 36 45 12.7 0.3 13 4.3 7.2 0.02 POS8 8 M8x1.25 12 9 25 10.4 22 42 53 15.875 0.3 14 7.2 11.6 0.03 POS10 10 M10x1.5 14 10.5 29 12.9 26 48 61 19.05 0.3 13 10 14.5 0.055POS12 12 M12x1.75 16 12 33 15.4 30 54 69 22.225 0.3 13 13.4 17 0.085POS14 14 M14x2.0 19 13.5 36 16.9 34 60 77 25.4 0.3 16 17 24 0.14 POS16 16 M16x2.0 21 15 40 19.4 40 66 86 28.575 0.3 15 21.6 28.5 0.21 POS18 18 M18x1.5 23 16.5 44 21.9 44 72 94 31.75 0.3 15 26 42.5 0.28 POS20 20 M20x1.5 25 18 47 24.4 50 78 103 34.925 0.3 14 31.5 52.5 0.38 POS22 22 M22x1.5 28 20 51 25.8 54 84 111 38.1 0.3 15 38 57 0.48 POS25 25 M24x2.0 31 22 57 29.6 60 94 124 42.85 0.3 15 47.5 68 0.64 POS28 28 M27x2.0 35 24 62 213 66 103 136 47.6 0.3 15 58 75.5 0.96 POS30 30 M30x2.0 37 25 66 34.8 70 110 145 50.8 0.3 17 64 88 1.1

- All dimensions are in mm - Rod body with right or left-hand female thread. - Outer race lined with bronze liner. - Surface of rod body zinc plated, rod body with a lubricating hole or grease nipple. - For left-hand thread, please add suffix “L”. e.g. POSL8.



Rod Ends SI..T/K series

Load ratings WeightPart # Dimensions mm

kN kg

d d3 B C1 L3 W d2 h1 L4 L5 d4 d5 dk a dyn. stat. 6H min. ≈ C C0

SI5T/K 5 M5x0.8 8 6 10 9 18 27 36 4 8.5 11 11.11 13 5.7 6 0.016SI6T/K 6 M6x1.0 9 6.75 12 11 20 30 40 5 10 13 12.7 13 7.2 7.65 0.022SI8T/K 8 M8x1.25 12 9 16 14 24 36 48 5 12.5 16 15.875 14 11.6 12.9 0.047SI10T/K 10 M10x1.5 14 10.5 20 17 28 43 57 6.5 15 19 19.05 13 14.5 18 0.077SI12T/K 12 M12x1.25 16 12 22 19 32 50 66 6.5 17.5 22 22.225 13 17 24 0.1 SI14T/K 14 M14x2.0 19 13.5 25 22 36 57 75 8 20 25 25.4 16 24 31 0.16 SI16T/K 16 M16x2.0 21 15 28 22 42 64 85 8 22 27 28.575 15 28.5 39 0.22 SI18T/K 18 M18x1.5 23 16.5 32 27 44 71 93 10 25 31 31.75 15 42.5 47.5 0.32 SI20T/K 20 M20x1.5 25 18 33 30 50 77 102 10 27.5 34 34.925 14 42.5 57 0.42 SI22T/K 22 M22x1.5 28 20 37 32 54 84 111 12 30 38 38.1 15 57 68 0.54 SI25T/K 25 M24x2.0 31 22 42 36 60 94 124 12 33.5 42 42.85 15 68 85 0.72 SI28T/K 28 M27x2.0 35 24 51 41 66 103 136 14 37 46 47.6 15 86 107 0.82 SI30T/K 30 M30x2.0 37 25 51 41 70 110 145 15 40 50 50.8 17 88 114 1.1 SI35T/K 35 M36x2.0 43 28 56 50 81 125 165.5 17 46 58 57.1 16 1.6 SI40T/K 40 M42x2.0 49 33 60 55 91 142 187.5 19 53 65 66.6 17 2.4 SI50T/K 50 M48x2.0 60 45 65 65 117 160 218.5 23 65 75 82.5 12 5

- All dimensions are in mm - Rod body with right or left-hand female thread. - It is made up of a maintenance-free radial spherical plain bearing G..PW and rod body. - Surface of rod body zinc plated. - For left-hand thread, please add suffix “L”. e.g. SIL 16 T/K.



Rod Ends SA..T/K series

Load ratings WeightPart # Dimensions mm

kN kg

d d3 B C1 L1 d2 L7 h L2 dk R1s a dyn. stat. 6g min. min. ≈ C C0

SA5T/K 5 M5x0.8 8 6 19 18 33 42 11.11 0.3 13 5.7 6 0.013SA6T/K 6 M6x1.0 9 6.75 21 20 36 46 12.7 0.3 13 7.2 7.65 0.02 SA8T/K 8 M8x1.25 12 9 25 24 42 54 15.875 0.3 14 11.6 12.9 0.038SA10T/K 10 M10x1.5 14 10.5 28 28 28 62 19.05 0.3 13 14.5 18 0.055SA12T/K 12 M12x1.75 16 12 32 32 54 70 22.225 0.3 13 17 24 0.085SA14T/K 14 M14x2.0 19 13.5 36 36 18 60 78 25.4 0.3 16 24 31 0.14 SA16T/K 16 M16x2.0 21 15 37 42 21 66 87 28.575 0.3 15 28.5 39 0.21 SA18T/K 18 M18x1.5 23 16.5 41 44 22 72 94 31.75 0.3 15 42.5 47.5 0.28 SA20T/K 25 M20x1.5 25 18 45 50 25 78 103 34.925 0.3 14 42.5 57 0.38 SA22T/K 22 M22x1.5 28 20 48 54 27 84 111 38.1 0.3 15 57 68 0.48 SA25T/K 25 M24x2.0 31 22 55 60 30 94 124 42.85 0.3 15 68 85 0.64 SA28T/K 28 M27x2.0 35 24 62 66 33 103 136 47.6 0.3 15 86 107 0.8 SA30T/K 30 M30x2.0 37 25 66 70 35 110 145 50.8 0.3 17 88 114 1.1 SA35T/K 35 M36x2.0 43 28 85 81 41 140 180.5 57.1 0.3 16 1.64 SA40T/K 40 M42x2.0 49 33 90 91 46 150 195.5 66.6 0.3 17 2.3 SA50T/K 50 M48x2.0 60 45 105 117 59 185 243.5 82.5 0.3 12 4.8

- All dimensions are in mm - Rod body with right or left-hand female thread. - It is made up of a maintenance-free radial spherical plain bearing G..PW and rod body. - Surface of rod body zinc plated. - For left-hand thread, please add suffix “L”. e.g. SAL 16 T/K.



Rod Ends for Hydraulic Components GK..DO series

Load ratings Weight Part # Dimensions mm

kN kg

d d1 B C1 dk d2 L4 h2 L7 L8 d3 d4 D a dyn. stat.

min ≈ C C0

GK10DO* 10 13.2 9 7 16 29 38.5 24 15 1.5 3 15 19 12 8.15 15.6 0.041GK12DO* 12 15 10 8 18 34 44 27 18 1.5 3 17.5 22 11 10.8 21.6 0.066GK15DO 15 18.4 12 10 22 40 51 31 20 2 4 21 26 8 17 32 0.12 GK17DO 17 20.7 14 11 25 46 58 35 23 2 4 24 30 10 21.2 40 0.19 GK20DO 20 24.2 16 13 29 53 64.5 38 27.5 2 4 27.5 35 9 30 54 0.23 GK25DO 25 29.3 20 17 36 64 77 45 33 3 4 33.5 42 7 48 72 0.43 GK30DO 30 34.2 22 19 41 73 87.5 51 37.5 3 4 40 47 6 62 95 0.64 GK35DO 35 39.8 25 21 47 82 102 61 43 3 4 47 55 6 80 125 0.96 GK40DO 40 45 28 23 53 92 115 69 48 4 4 52 62 7 100 156 1.3 GK45DO 45 50.8 32 27 60 102 128 77 52 4 6 58 68 7 127 208 1.8 GK50DO 50 55.9 35 30 66 112 144 88 59 4 6 62 75 6 156 250 2.5 GK60DO 60 66.8 44 38 80 135 167.5 100 72.5 4 6 70 90 6 245 390 3.9 GK70DO 70 77.9 49 42 92 160 195 115 86 5 6 80 105 6 315 510 6.6 GK80DO 80 89.4 55 47 105 180 231 141 98 5 6 95 120 6 400 620 8.7

- All dimensions are in mm - Rod end housing with weldable base and dowel pin. - It is made up of a radial spherical plain bearing GE..ES or GE..ES 2RS and rod end housing. - Rod end housing with a lubricating hole or grease nipple. - Sealed design also available, e.g. GK 50 DO 2RS. - Relubrication not possible for the sizes marked “*”.



Rod Ends for Hydraulic Components GF..DO series

Part # Dimensions mm Load ratings kN Weight

kg

d C1 B d2 L6 h2 dk d1 D L8 dyn. stat.

C C0

GF20DO 20 19 16 50 63 38 29 24.2 35 2 30 67 0.35 GF25DO 25 23 20 55 72.5 45 35.5 29.3 42 2 48 69.5 0.53 GF30DO 30 28 22 65 83.5 51 40.7 34.2 47 2 62 118 0.87 GF35DO 35 30 25 83 102.5 61 47 39.8 55 2 80 196 1.5 GF40DO 40 35 28 100 119 69 53 45 62 3 100 300 2.4 GF45DO 45 40 32 110 132 77 60 50.8 68 3 127 380 3.4 GF50DO 50 40 35 123 149.5 88 66 55.9 75 3 156 440 4.4 GF60DO 60 50 44 140 170 100 80 66.8 90 4 245 570 7.1 GF70DO 70 55 49 164 197 115 92 77.9 105 4 315 695 10.5 GF80DO 80 60 55 180 231 141 105 89.4 120 4 400 780 15 GF90DO 90 65 60 226 263 150 115 98.1 130 4 490 1340 23.5

GF100DO 100 70 70 250 295 170 130 109.5 150 4 610 1500 31.5 GF110DO 110 80 70 295 332.5 185 140 121.2 160 4 655 2160 48.5 GF120DO 120 90 85 360 390 210 160 135.5 180 4 950 3250 79

- All dimensions are in mm - Rod end housing with weldable base. - It is made up of a radial spherical plain bearing GE..ES or GE..ES 2RS and rod end housing. - Rod end housing with a lubricating hole or grease nipple. - Sealed design also available, e.g. GF 70 DO 2RS.



Rod Ends for Hydraulic Components GF..LO series


ratings kN Weight

kg

d B d1 h2 d2 C1 L6 a dyn. stat.

≈ C C0

GF20LO 20 20 25 38 50 19 63 4 30 74 0.36 GF25LO 25 25 30.5 45 55 23 72.5 4 48 95 0.54 GF32LO 32 32 38 65 70 27 100 4 62.5 168 1.12 GF40LO 40 40 46 69 100 35 119 4 100 268 2.5 GF50LO 50 50 57 88 123 40 149.5 4 156 362 4.6 GF63LO 63 63 71.5 107 145 50 179.5 4 248 570 9.3 GF70LO 70 70 79 115 164 55 197 4 315 800 11.25 GF80LO 80 80 91 141 180 60 231 4 400 874 15.75 GF90LO 90 90 99 150 226 65 263 4 490 1045 24

GF100LO 100 100 113 170 250 70 295 4 610 1330 33.95 GF110LO 110 110 124 185 295 80 332.5 4 655 1490 49

- All dimensions are in mm - Rod end housing with weldable base. - It is made up of a radial spherical plain bearing GE..LO and rod end housing. - Rod end housing with a lubricating hole or grease nipple. - Sealed design also available, e.g. GF 70 LO 2RS.



Rod Ends for Hydraulic Components GIHR..DO series


ratings kNWeight

kg

d d3 d4 L3 B C1 d2 L7 h1 L4 d5 d1 dk a dyn. stat. 6H min. min. ≈ C C0

GIHR20DO 20 M16x1.5 25 17 16 19 56 25 50 80 46 24.2 29 9 30 72 0.43 GIHR25DO 25 M16x1.5 25 17 20 23 56 28 50 80 46 29.3 35.5 7 48 72 0.48 GIHR30DO 30 M22x1.5 32 23 22 28 64 30 60 94 50 34.2 40.7 6 62 106 0.74 GIHR35DO 35 M28x1.5 40 29 25 30 78 38 70 112 66 39.8 47 6 80 153 1.2 GIHR40DO 40 M35x1.5 49 36 28 35 94 45 85 135 76 45 53 7 100 250 2 GIHR50DO 50 M45x1.5 61 46 35 40 116 55 105 168 90 55.9 66 6 156 365 3.8 GIHR60DO 60 M58x1.5 75 59 44 50 130 65 130 200 120 66.8 80 6 245 400 5.4 GIHR70DO 70 M65x1.5 86 66 49 55 154 75 150 237 130 77.9 92 6 315 540 8.5 GIHR80DO 80 M80x2.0 105 81 55 60 176 80 170 265 160 89.4 105 6 400 670 12 GIHR90DO 90 M100x2.0 124 101 60 65 206 90 210 323 180 98.1 115 5 490 980 21.5

GIHR100DO 100 M110x2.0 138 111 70 70 230 105 235 360 200 109.5 130 7 610 1120 27.5 GIHR110DO 110 M120x3.0 152 125 70 80 265 115 265 407.5 220 121.2 140 6 655 1700 40.5 GIHR120DO 120 M130x3.0 172 135 85 90 340 140 310 490 257 135.5 160 6 950 2900 76

- All dimensions are in mm - Rod end housing with right or left-hand female thread. - It is made up of a radial spherical plain bearing GE..ES or GE..ES 2RS and rod end housing. - Rod end housing with a lubricating hole or grease nipple.



Rod Ends for Hydraulic Components GIHR-K..DO series


ratings kNWeight

kg

d d3 d4 L3 B C1 d2 L7 h1 L4 d5 d1 dk a dyn stat

6H min min ≈ C C0

GIHR-K20DO 20 M16x1.5 25 17 16 19 56 25 50 80 46 24.2 29 9 30 72 0.43 GIHR-K25DO 25 M16x1.5 25 17 20 23 56 28 50 80 46 29.3 35.5 7 48 72 0.48 GIHR-K30DO 30 M22x1.5 32 23 22 28 64 30 60 94 50 34.2 40.7 6 62 106 0.74 GIHR-K35DO 35 M28x1.5 40 29 25 30 78 38 70 112 66 39.8 47 6 80 153 1.2 GIHR-K40DO 40 M35x1.5 49 36 28 35 94 45 85 135 76 45 53 7 100 250 2 GIHR-K50DO 50 M45x1.5 61 46 35 40 116 55 105 168 90 55.9 66 6 156 365 3.8 GIHR-K60DO 60 M58x1.5 75 59 44 50 130 65 130 200 120 66.8 80 6 245 400 5.4 GIHR-K70DO 70 M65x1.5 86 66 49 55 154 75 150 237 130 77.9 92 6 315 540 8.5 GIHR-K80DO 80 M80x2.0 105 81 55 60 176 80 170 265 160 89.4 105 6 400 670 12 GIHR-K90DO 90 M100x2.0 124 101 60 65 206 90 210 323 180 98.1 115 5 490 980 21.5

GIHR-K100DO 100 M110x2.0 138 111 70 70 230 105 235 360 200 109.5 130 7 610 1120 27.5 GIHR-K110DO 110 M120x3.0 152 125 70 80 265 115 265 407.5 220 121.2 140 6 655 1700 40.5 GIHR-K120DO 120 M130x3.0 172 135 85 90 340 140 310 490 257 135.5 160 6 950 2900 76

- All dimensions are in mm - Rod end housing with right or left-hand female thread. - It is made up of a radial spherical plain bearing GE..ES or GE..ES 2RS and rod end housing. - With locking slot and nut. - Rod end housing with a lubricating hole or grease nipple.



Rod Ends for Hydraulic Components GIHN-K..LO series

WeightPart # Dimensions mm

Load ratings kN kg

d B C1 d3 d4 L3 d2 L4 h1 L7 C2 d5 dyn. stat. 6H min. min. C C0

GIHN-K12LO* 12 12 11 M12x1.25 16.5 17 32 54 38 14 11 32 10.8 24.5 0.1 GIHN-K16LO 16 16 14 M14x1.5 21 19 40 64 44 18 14 40 17.6 36.5 0.2 GIHN-K20LO 20 20 17 M16x1.5 25 23 47 77 52 22 17 47 30 48 0.4 GIHN-K25LO 25 25 22 M20x1.5 30 29 58 96 65 27 19 54 48 78 0.66 GIHN-K32LO 32 32 28 M27x2.0 38 37 71 118.5 80 32 22 66 67 114 1.2 GIHN-K40LO 40 40 33 M33x2.0 47 46 90 146 97 41 26 80 100 204 2.1 GIHN-K50LO 50 50 41 M42x2.0 58 57 109 179.5 120 50 32 96 156 310 4.4 GIHN-K63LO 63 63 53 M48x2.0 70 64 136 213 140 62 38 114 255 430 7.6 GIHN-K70LO 70 70 57 M56x2.0 80 76 155 245 160 70 42 135 315 540 9.5 GIHN-K80LO 80 80 66 M64x3.0 90 86 168 270 180 78 48 148 400 695 14.5 GIHN-K90LO 90 90 72 M72x3.0 100 91 185 296 195 85 52 160 490 750 17 GIHN-K100LO 100 100 84 M80x3.0 110 96 210 322 210 98 62 178 610 1060 28 GIHN-K110LO 110 110 88 M90x3.0 125 106 235 364 235 105 62 190 655 1200 32 GIHN-K125LO 125 125 102 M100x3.0 135 113 260 405 260 120 72 200 950 1430 43

- All dimensions are in mm - Rod end housing with right or left-hand female thread. - It Is made up of a radial spherical plain bearing GE..LO and rod end housing. - With locking slot and nut. - Rod end housing with a lubricating hole or grease nipple. - Relubrication not possible for the size marked “*”.



Clevises DIN 71752/ISO 8140 G series

WeightPart # Dimensions mm

kg

d1 g a1 a2 b1 b2 d2 d3 f L1 L2 L3 r 0.3

H9 ±0.5 h11 -0.16 B13 ±0.3 ±0.2 ±0.5 ±0.2

0.3G4x8 4 8 8 8 4 4

0.2M4x0.7 8 0.5 21 16±0.3 6 1 0.005

0.3G4x16 4 16 8 8 4 4

0.2M4x0.7 8 0.5 29 24±0.3 6 1 0.007

0.3G5x10 5 10 10 10 5 5

0.2M5x0.8 9 0.5 26 20±0.3 7.5 1 0.009

0.3G5x20 5 20 10 10 5 5

0.2M5x0.8 9 0.5 36 30±0.3 7.5 1 0.013

0.3G6x12 6 12 12 12 6 6

0.2M6x1.0 10 0.5 31 24±0.3 9 1 0.015

0.3G6x24 6 24 12 12 6 6

0.2M6x1.0 10 0.5 43 36±0.4 9 1 0.021

0.3G8x16 8 16 16 16 8 8

0.2M8x1.25 14 0.5 42 32±0.4 12 1 0.037

0.3G8x16FG 8 16 16 16 8 8

0.2M8x1.0 14 0.5 42 32±0.4 12 1 0.037

0.3G8x32 8 32 16 16 8 8

0.2M8x1.25 14 0.5 58 48±0.4 12 1 0.054

0.3G8x32FG 8 32 16 16 8 8

0.2M8x1.0 14 0.5 58 48±0.4 12 1 0.054

0.3G10x20 10 20 20 20 10 10

0.2M10x1.5 18 0.5 52 40±0.4 15 1 0.074

0.3G10x20FG 10 20 20 20 10 10

0.2M10x1.25 18 0.5 52 40±0.4 15 1 0.074

0.7G10x40 10 40 20 20 10 10

0.2M10x1.5 18 0.5 72 60±0.4 15 1 0.116

0.7G10x40FG 10 40 20 20 10 10

0.2M10x1.25 18 0.5 72 60±0.4 15 1 0.116

0.7G12x24 12 24 24 24 12 12

0.2M12x1.75 20 0.5 62 48±0.4 18 1 0.121

0.7G12x24FG 12 24 24 24 12 12

0.2M12x1.25 20 0.5 62 48±0.4 18 1 0.121

0.7G12x48 12 48 24 24 12 12

0.2M12x1.75 20 0.5 86 72±0.4 18 1 0.175

0.7G12x48FG 12 48 24 24 12 12

0.2M12x1.25 20 0.5 86 72±0.4 18 1 0.175

0.7G14x28 14 28 27 27 14 14

0.2M14x2.0 24 1 72 56±0.4 23 1 0.178

0.7G14x28FG 14 28 27 27 14 14

0.2M14x1.5 24 1 72 56±0.4 23 1 0.178



0.7G14x56 14 56 27 27 14 14

0.2M14x2.0 24 1 101 85±0.4 23 1 0.258

0.7G14x56FG 14 56 27 27 14 14

0.2M14x1.5 24 1 101 85±0.4 23 1 0.258

0.7G16x32 16 32 32 32 16 16

0.2M16x2.0 26 1 83 64±0.4 24 1 0.282

0.7G16x32FG 16 32 32 32 16 16

0.2M16x1.5 26 1 83 64±0.4 24 1 0.282

0.7G16x64 16 64 32 32 16 16

0.2M16x2.0 26 1 115 96±0.4 24 1 0.411

0.7G16x64FG 16 64 32 32 16 16

0.2M16x1.5 26 1 115 96±0.4 24 1 0.411

0.7G18x36 18 36 36 36 18 18

0.2M18x2.5 30 1 94 72±0.4 27 2 0.39

0.7G18x36FG 18 36 36 36 18 18

0.2M18x1.5 30 1 94 72±0.4 27 2 0.39

0.7G20x40 20 40 40 40 20 20

0.2M20x2.5 34 1 105 80±0.4 30 2 0.55

0.7G20x40FG 20 40 40 40 20 20

0.2M20x1.5 34 1 105 80±0.4 30 2 0.55

0.7G20x80 20 80 40 40 20 20

0.2M20x2.5 34 1 145 120±0.4 30 2 0.8

0.7G20x80FG 20 80 40 40 20 20

0.2M20x1.5 34 1 145 120±0.4 30 2 0.8

0.7G25x50 25 50 50 50 25 25

0.2M24x3.0 42 1.5 132 100±0.4 36 2 1.1

0.7G25x50FG 25 50 50 50 25 25

0.2M24x2.0 42 1.5 132 100±0.4 36 2 1.1

0.7G28x56 28 56 55 55 28 28

0.2M27x3.0 48 1.5 148 112±0.4 40 2 1.5

0.7G28x56FG 28 56 55 55 28 28

0.2M27x2.0 48 1.5 148 112±0.4 40 2 1.5

0.7G30x54FG 30 54 55 55 30 30

0.2M27x2.0 48 1.5 148 110±0.4 40 2 1.44

0.7G30x60 30 60 60 60 30 30

0.2M30x3.5 52 1.5 160 120±0.4 42 2 1.97

0.7G30x60FG 30 60 60 60 30 30

0.2M30x2.0 52 1.5 160 120±0.4 42 2 1.97

0.7G35x54FG 35 54 70 70 35 35

0.2M36x2.0 60 2 188 144±0.4 54 3 2.93

0.7G35x72 35 72 70 70 35 35

0.2M36x4.0 60 2 188 144±0.4 54 3 2.93

0.7G35x72FG 35 72 70 70 35 35

0.2M36x2.0 60 2 188 144±0.4 54 3 2.93

0.7G36x72 35 72 70 70 36 36

0.2M36x4.0 60 2 188 144±0.4 54 3 2.93

0.7G36x72FG 35 72 70 70 36 36

0.2M36x2.0 60 2 188 144±0.4 54 3 2.93

0.7G40x84FG 40 84 85 85 40 40

0.2M42x2.0 70 3 232 168±0.4 64 5 5.64

0.7G42x84 42 84 85 85 42 42

0.2M42x4.5 70 3 232 168±0.4 64 5 5.34

0.7G42x84FG 42 84 85 85 42 42

0.2M42x2.0 70 3 232 168±0.4 64 5 5.34

0.7G50x96 50 96 96 96 50 50

0.2M48x5.0 82 3 265 192±0.4 73 5 7.86

0.7G50x96FG 50 96 96 96 50 50

0.2M48x2.0 82 3 265 192±0.4 73 5 7.86


1) Standard: DIN 71752/DIN ISO 8140 2) Code for thread: regular thread, left-handed—LH; fine-pitch thread—FG; fine-pitch thread, left-handed—FGLH 3) Radius or 45° beveling (at manufacturer's choice)

- Material: 1) Low Carbon Steel 1020; 2) Alternative: Stainless Steel 304

- Surface protection: Polished and oiled; Optional: electroplated galvanized, passivated in white-blue or yellow



Clevises with Male Thread GM series

d1 g a1 a2 b d2 f l1 l2 l3 l4 r h9 ±0.5 h11 0.5 0.7 ±0.2 ±0.2 ±0.4 ±0.2 Part #

-0.2 0.15

Weight 7.85kg/dm3

kg≈

GM6x1 6 12 12 12 6 M6x1 0.5 44 37 20 15 0.8 0.015 GM8x1.25 8 16 16 16 8 M8x1.25 0.5 57 47 25 20 0.8 0.036 GM10x1.5 10 20 20 20 10 M10x1.5 0.5 69 57 30 25 0.8 0.068

GM12x1.75 12 24 24 24 12 M12x1.75 0.5 82 68 35 30 0.8 0.122 GM14x2 14 28 27 27 14 M14x2 1 94 78 40 35 1.2 0.171 GM16x2 16 32 32 32 16 M16x2 1 108 89 45 40 1.2 0.288

GM20x2.5 20 40 40 40 20 M20x2.5 1 134 109 55 50 1.5 0.55

- All dimensions are in mm - Notes: Standard: similar DIN71752/ DIN ISO 8140 / Cetop-standard

Code for thread: regular thread, left-handed—LH; fine-pitch thread—FG; fine-pitch thread, left-handed—FGLH Radius or 45° beveling (at manufacturer's choice)

- Material: Low Carbon Steel 1020; Alternative: Stainless Steel 304 - Surface protection: Polished and oiled: Optional: electroplated galvanized, passivated in white-blue or yellow

NINGBO KYLIN MACHINERY CO., LTD. -...

Documents

Transcript of NINGBO KYLIN MACHINERY CO., LTD. -...