NEW SX-200 HIGH PRECISION AND HIGH CAPACITY ......The high performance SARIX Micro Pulse EDM...
Transcript of NEW SX-200 HIGH PRECISION AND HIGH CAPACITY ......The high performance SARIX Micro Pulse EDM...
-
NEW SX-200HIGH PRECISION AND HIGH CAPACITY
MICRO EROSION MACHINE
IF YOU NEED THIS TOP
PERFORMANCE WITH REDUCED
MACHINING TIMES, WITHOUT
MATERIAL ALTERATION, CALL SARIX
OR VISIT US
@WWW.SARIX.COM
SARIX SA6616 LOSONESWITZERLAND
TEL. +41 91 785 81 71FAX +41 91 785 81 77
www.sarix.com
PERFECT ROUND HOLES.CONCENTRIC &
ACCURATE HOLES.HOLE TAPER CONTROLLED.
NO ANGLE LIMIT.NO BURNING EFFECT.
NO MATERIAL ALTERATION.WITHOUT ENTRANCE AND
EXIT DEFORMATION.HIGH PRODUCTIVITY QUALITY.
HIGH QUALITY SURFACE.HIGH PRECISION FINISHING.
AUTOMOTIVE
TEXTILE
MICRO MOLDS
MICRO MECANICS
AEROSPACE
MEDICAL
MICRO ELECTRONIC
● The capacity of the NEW SX-200 machinebrings the Micro EDM Technology to largerwork pieces.
● NEW the multi-axis CNC allows the index-ing of complex work pieces where the per-formance of the Micro-EDM-Machining isneeded.
● NEW “High production capabilityconcept” through an efficient Multi-functions Micro-Machining machine with;slide W-axis (Z2), C-indexing spindle, A/B positioning indexing axis and multiple hole sequence process….
● NEW SX-MMI, ”On-board”, easy and user friendly unlimited programming andediting software.
● The high performance SARIX Micro PulseEDM generator MPS, with its associatedTechnology opens up new opportunities
for smaller, deeper and more precise perfect holes.
● Micro EDMing machining technology withsolid and tube electrode from 45 micronsto 3.0 mm.
● Micro Holes, high Precision Micro holesand shape holes down to 20 microns
● High surface finishing capability down toRa 0.1 and Ra 0.05 with the Micro FinePulse Shape Generator MFPS.
● High precision positioning accuracy up to±1 micron.
● Automatic axis positioning control withdepth control.
● NEW High precision Automatic electroderefeeding spindle with dielectric or airclamping control for continuous production.
● High Speed Micro EDM drilling Technolo-gy with breakthrough-detection device.
SX-200-HPM
MPSMicro Pulse Shape Generator
SX-CU
-
SARIX SA • CH - 6616 LOSONE • TEL. +41 91 785 8171 • FAX +41 91 785 8177 • www.sarix.com • e-mail: [email protected]
TECHNICAL SPECIFICATIONS TYPICAL CONFIGURATION Machine SX-200
HPM
Type High Precision
Work table size 700 x 300 mm
Travel X axis 350 mm
Travel Y axis 200 mm
Travel Z axis 200 mm
Travel W (Z2)* axis 150 mm
Z axis feed rate: max 450 mm/min
X/Y axis speed rate: max 600 mm/min
Precision of positioning ±2 µm
Resolution 0.1 µm
Adjustable workheadpositioning 50/100/150 mm
Work piece weight ~50 kg
Net weight ~450 kg
Dimensions 900 x 820 x 950 mm
SX-MPS SX-HPS Generator: MICRO PULSE SHAPE HIGH PULSE SHAPE
Freerun voltage 60 ÷ 255 V fixed voltage
Frequency 1÷250 pos. 1÷100 pos.
Current pulse 1÷200 pos. 1÷200 pos.
Dimensions 135 x 110 x 500 mm
Control Unit SX-CU
Power supply 230 V / 50 Hz
Nominal power connection 650 VA
Dimensions 450 x 400 x 690 mm
Dielectric Unit SX-DA
Capacity 25 l
Dielectric deionised water or oil
Dimensions 500 x 750 x 620 mm
Our specifications are subject to any change, givingyou a continous technological advantage
● SX-200-HPM machine including SX-MPS, Micro Pulse Shape Generator● NEW SX-CU, CNC Control UNIT ● SX-PL, Multi-axis-erosion software X-Y-Z● SX-ICON, Software Icon Editor● SX-DA, Dielectric unit with conductivity and/or temperature control for mass
production (for deionised water or dielectric oil)● SX-RHP, High Precision Rotation axis with 3R Macro chuck● SX-PG, Precision Guide holder● SX-HP, High pressure flushing unit 70 bars
NEW SX-CU CNC CONTROL UNIT ● Unlimited program capacity; number, length and calls ● Free and unlimited technology settings● SX-MMI, “On board” friendly user editing and programming capability● NEW SX-EAC, “Enhanced Automatic Configuration” System● High quality 8.4” TFT color display, 3.5” floppy disc driver, 1.44 MB● Virtually up to 16 axis CNC control● Standard X,Y,Z and rotation speed axis control (W,A,B,C…optional)
● SX-MFPS, Micro Fine Pulse Shape generator for Micro-Shape-holes with ultra-fine finishing
● SX-HPS, High Power Pulse Shape generator for higher stock removal● NEW SX-A320 & SX-A340, High precision Automatic Electrode refeeding
spindle, (also available with high pressure flushing unit for deionised water ordielectric Oil)
● SP 06 & SP 08, Automatic refeeding collet down to 45 Microns● NEW SX-C-RHP, High Precision Rotating and indexing C axis● NEW SX-W, CNC Programmable W-backslide axis (Z2)● SX-CC, “CriCri”, Electrode wear compensation system for shape electrode● NEW SX-TH, “Tilting Head” device for SX-A340 Rotating spindle with the
SP08 collet type● SX-DNC, Sequencer software for unlimited programmable number of holes● SX-AB100C, High precision single or double indexable and programmable
A/B-axis, designed for submerged conditions● SX-ST200 & ST300, collapsible tank for submerged conditions● SX-Wdress020, Wire Dress Unit to produce Micro-Electrode for Micro Holes
and shape holes down to 20 Microns● NEW SX-EAD, Electrode Automatic Distributor device
OPTIONS
ACCESSORIES● SP01, High precision collet with centering device● SP02, High precision collet● SG01, High precision ceramic guide● High precision collet down to 45 Microns● High precision solid carbide tubes● Brass & Copper single holes and coreless electrodes tubes● Tooling, fixtures, horizontal microscope, instruments, filters…● Special shaped and complex form according your drawing…
* Option
In the regionwhere
avant-gardetechnologyhas made
EDMhistory.
SARIX F-SX-200e - 05