7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 1/25

THESE "BOW TIE" FIGURES ARE USED TOREGISTER ADJOINING SHEETS WHEN

YOU TAPE THEM TOGETHER.

DRILL/CUT OPTIONALCOOLING AIR INLET HERE

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 2/25

FUTABAR617FS

RECEIVER

MAKE RELIEF CUTS ININNER SKIN AS REQUIRED

TO MAKE CURVE

LOCATE BATTERY AS REQUIRED FOR CG

FUSELAGE SIDE9/16 PINK FOAM,MAKE 2

HATCH MADE FROM 5MM MIDWESTCELLFOAM 88, PROFORMANCE FOAMOR SIMILAR

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 3/25

Castle CreationsPhoenix 35 ESC

CC-BEC

SAND INSIDE EDGE AS REQUIRED TO FULLYSEAT FAN UNIT. BOND WITH 5-MIN. EPOXY

1.3" (33mm) x 9/16" pink foam strip

HYPERFLOW FAN AMMO 24-45-3790

MOTOR

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 4/25

LEAVE THIS AREA OPENFOR COOLING AIR EXIT

BEVEL INSIDE FACE IN THIS AREA45˚ FOR V-TAIL MOUNT

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 5/25

FAN SHROUD FROM 3MMFOAM. MAKE 1, TRIM TO FIT

MAKE LENGHTWISE RELIEF CUTS

1/8-INCH APART ON BOTTOM

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 6/25

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 7/25

 

1.3 x 9/16-INCH PINK FOAM STRIPINSET BETWEEN FUSELAGE SIDES.MAKE RELIEF CUTS AS REQUIREDIN INNER SKIN TO MAKE CURVE.

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 8/25

 ADD ESC ACCESS HOLE AS DESIRED

BATTERYHATCH

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 9/25

V-TAIL SURFACES, ACTUAL SIZEMAKE 2 FROM 5MM CELLFOAM88

3/4-INCH STRAPPING TAPE,OPTIONAL BOTH SIDES.

SINGLE BEVEL CONTROL SURFACESWITH TAPE HINGE ON TOP SURFACE

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 10/25

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 11/25

HS-55

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 12/25

CUT WINGLETS FROM 3MMCELLFOAM88

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 13/25

FUSELAGE SIDE

FAN UNIT

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 14/25

5MM CARBON FIBER SPARTUBE IN WING BOTTOM

WING CORES AVAILABLE FROM WWW.FLYINGFOAM.COM

PINK FOAM, 12% CLARK-Y AIRFOIL WITH 5MM THICK TRAILING EDGE

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 15/25

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 16/25

H  S  - 5  5 

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 17/25

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 18/25

SET V-TAIL SURFACES AT 45˚ ANGLE FROM HORIZONTAL

1.3 X 9/16-INCH PINK FOAM STRIP

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 19/25

LEAVE 1/8 LIP FOR GLUINGFAN SHROUD

CUT AILERONS FROM 5MM CELLFOAM88SINGLE BEVEL LEADING EDGE AND TOP HINGE WITH TAPE.

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 20/25

NOTES:

1. FOAM SOLD AS 1/2 IN THICK BUT MEASURES 9/162. COVER WITH LOW-TEMP TOWERKOTE IRON-ON FILM OR SIMILAR3. BALANCE MODEL 1-3/16 INCHES BEHIND WING LEADING EDGE AS SHOWN

4. WING AND TAIL SET AT 0˚ INCIDENCE5. PROTOTYPE FLEW WITH 3S 1300MAH & 4S 2000MAH PACKS6. CONTROL THROWS

 AILERONS: +/- 3/8 INELEVATOR: +/- 1/2 INRUDDER: +/- 1/2 IN

7. ADHESIVES USEDZAP FOAM-SAFE CA - FAN SHROUDGORILLA GLUE - FUSELAGE5-MIN. Z-POXY - FAN INSTALL, V-TAIL30-MIN. Z-POXY - WING, SPAR

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 21/25

42 3 5 6

SCALE - INCHES

1

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 22/25

THIS PLAN MAY BE PHOTOCOPIED AND ENLARGED

FOR PERSONAL MODELING USE ONLY ALL COMMERCIAL RIGHTS RESERVED

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 23/25

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 24/25

DESI 

7/25/2019 New Moon Tiled

http://slidepdf.com/reader/full/new-moon-tiled 25/25

New Moon A FANTASY-SCALE JET 

NSPIRED BY MOONEY AIRCRAFT 

NED AND DRAWN BY TERRY DUNN 

WINGSPAN:LENGTH:

WING AREA:WEIGHT:

POWER SYSTEM

FAN:MOTOR:

BATTERY:

©2011, MAPLEGATE MEDIA GROUP AND TERRY DUNN ALL RIGHTS RESERVED

DRAWN WITH AUTOCAD AND ASHLAR-VELLUM GRAPHITE CAD SOFTWARE

30.5 IN25 IN152.5 SQ IN17-22 OZ

GREAT PLANES HYPERFLOW200-WATT MINIMUM3S 1300 - 4S 2200MAH LIPO