New InteliSysNT RELATED PRODUCTS Worldwide ... POWER CONTROL CENTER-BB IV 8 Mexico Generator room at...
Transcript of New InteliSysNT RELATED PRODUCTS Worldwide ... POWER CONTROL CENTER-BB IV 8 Mexico Generator room at...
New InteliSysNT
PREMIUM AND COGENERATION GEN–sET CONTROllER
ComAp is a member of AMPS (The Association of Manufacturers of Power generating Systems).
Selected ComAp products have the UL Certification.
ComAp products meet the highest standards, with every stage of production undertaken in accordance with the ISO certification obtained in 1998.
TWO UNIT SYSTEM BaseBox + DisplayInteliSysNT BaseBox and InteliVision 8
New InteliSysNT RELATED PRODUCTS Worldwide references
GCB #3
CGCB
J1939
GCB #1
MAINS #1
MASTER
SELECTOR
FEEDBACK
MASTER
SELECTOR
MCB #1
MAN 1, 2, 3
GCB #2
MAINS #2
MCB #2
MAINS #3
MCB #3
MainsPro
MainsPro
MainsPro
MCB
GCB
1, 2, 3
PLC
POWER CONTROL
CENTER
IS-NT-BB
IV 8
MexicoGenerator room at Hotel Sandos, Quintana Roo
The first InteliVision units operating in Mexico are installed in a prestigious hotel Sandos close to the famous Riviera Maya beach area.
“The staff on site were delighted how easy and quick it was to inspect the gen-set using the new large colourful screens on the InteliVision unit, and the benefits provided by new features, especially trends reporting.”
Agustin de Jesus Garcia PastranaDupont Elektric Mexico Technician
SwitzerlandShunting loco at Holcim cement factory
The shunting locomotive re-power application uses an InteliDrive Mobile for the complete control, monitoring and protection of the Volvo D16 engine which drive a Voith Hydro – Turbo gear-box for propulsion via a systemof push-rods.
Full communication between engine, ID-Mobile and the two InteliVision displays is achievedwith J1939 CAN bus – making the system wiring and integration very simple.All values, warnings and fault codes from the engine (EMS) are displayed on the two large InteliVision displays, located on both sides of the locomotive cabin.
CANADAParalleling system for Oil sand camp
“When I first saw InteliVision at PowerGen, I immediately recognised its potential for our power generation systems. The large easy to read colour display and customer-friendly interactivity is precisely what our customers have been looking for. We have already installed systems with InteliVision and received very positive feedback from our customers on the units performance.”
Santokh Sahota P. Eng Simson MaxwellEngineering Manager
USACompressor applications
“With the introduction of the InteliVision and our usage of ComAp hardware we now have a whole new market to pursue through the introduction of our own brand of compressor control panel. The ComAp hardware allows us to be fully Modbus capable and it integrates well with the engine manufactures controls.”
Dale ShowsSEC EnergyProducts & Services
IG-NT-BB
InteliVision 5 InteliVision 5
DescriptionInteliSysNT is an expandable controller for both single and multiple gen-sets operating in standby or parallel modes, especially in cogeneration (CHP) and other complex applications.
InteliVision 8 is a new generation colour display unit for either InteliGenNT, InteliSysNT, InteliMainsNT or InteliDrive controllers. It is designed as a simple, easy to use Plug and Play solution, which also features our unique TRENDS monitoring as a standard feature.
Benefits � Support of engines with ECU
(Electronic Control Unit) � Excellent configurability to match
customers’ needs exactly � Complete integrated gen-set
solution and signal sharing via CAN bus – minimum external components needed
� Many communication options – easy remote supervising and servicing
� Perfect price / performance ratio � Gen-set performance log for
easy problem tracing � Built-in PLC � 8” Colour TFT display � Active buttons – fast access
to important data � Trends � InteliVision 8 is possible to
connect via RS 232/485, CAN � Plug and play system � Sealed to IP65AirGate
Modern communications made simple. ComAp’s powerful AirGate technology is provided in a range of our controllers and makes remote internet connection to the ComAp controller easy.Just register the AirGate enabled controller on our website and from then on let ComAp’s uniquesystem locate and maintain contact with the controller, no need to worry about VPN’s, Static IPaddresses or corporate firewalls, simple! “AirGate – Simply connected.”
Features and specification are subject to change without prior notice 2010-11/CPLEISV8
ComAp, spol. s r. o.Czech RepublicPhone: + 420 246 012 111 Fax: + 420 266 316 647E-mail: [email protected]: www.comap.cz
MANuFACTurEr: LoCAL DISTrIBuTor / PArTNEr:
Customer satisfaction is our mission. We continuously develop the best people to succeed in our mission.
New InteliMainsNT
MAINs sUPERvIsION CONTROllER
� New InteliMainsNT is designed for multiple (up to 31) gen-sets operating in parallel to mains. New InteliMainsNT controller connects the group of gen-sets to the mains. It can serve as a bus-tie synchronizing controller between two groups of gen-sets.
� New InteliMainsNT: IM-NT-BB + InteliVision 5
HW modifications
Typical application
MULTIPLE LOADS – SEvERAL MAINS SUPPLIESDescription:
� In case of manipulation, the system switches from one branch to another by turning of the Master Selector Switch (MSS): BO MSS turn is used to turn the MSS.
� The mains voltage measurement, generator current measurement, MCB and GCB feedbacks, MCB and GCB control signals and Mains Failure (MF) signals (MainsPro outputs) are switched by the MSS, so that the system continuously ”sees” only the selected branch.
� MCB and GCB are operated by pulse signal (GCB open/close, MCB close). The pulse is issued as a request for CB operation and terminated at the moment of corresponding feedback receipt.
� The MainsPro relays monitor mains on all 3 branches. In case of any MF, the gen-set is started. � In case of MF on any branch, the proper MainsPro opens MCB, MSS switches to the failed branch and closes GCB. � If a MF occurs on a different branch at the same moment, the controller finishes manipulation
of GCB, MSS switches to a different branch and closes the other GCB. � After an existing MF state terminates on any branch, the MSS turns to this branch,
InteliSysNT reverse-synchronizes and closes MCB and opens GCB. Short-time parallel is allowed on the current branch.
� The MSS is blocked from moving away from a branch, where: – parallel operation is in effect – GCB open/close or MCB close signals are active – MF signal is in effect and GCB is open
� In case that all existing MF are solved and all GCB’s are open, the gen-set stops.
scope of supply:
� 1× PLC (not delivered by ComAp) � 1× Motorized rotary switch with
3× 16 contacts (not delivered by ComAp) � 1× InteliSysNTC BaseBox � 1× InteliVision 8 � 3× MainsPro � 1× IG-AVRi � 1× IG-AVRi-TRANS/LV
InteliGenNT ColourAll IN ONE GEN-sET CONTROllER
� InteliGenNT Colour is a comprehensive controller for both single and multiple gen-sets operating in standby or parallel modes.
� InteliGenNT Colour: IG-NT-BB + InteliVision 5
IM-NT-BB
Base box Display Brief info
IS-NTC-BB InteliVision 5 Control unit with detachable colour display
IS-NTC-BB InteliVision 8 Control unit with detachable colour display
Intelivision 8InteliSysNTC BaseBox
New InteliSysNT New InteliSysNT New InteliSysNT
PC
PC
InteliVision 8#1
MODEMPC MODEM
IS-BIN16/8
IS-AIN8
I-CB/XX
IGS-PTM
IGL-RA15
I-CB/XX
I-AOUT8ENGINE
16 BINARY
OUTPUTS
(OPEN
COLLECTOR)
4 ANALOG
INPUTS
GENERATORMAINS
IS-NTC-BB
EARTH FAULT
CURRENT
CURRENTVO
LTAGE
SG O
UT
AVRi OUT
INTER-CONTROLLER
& MONITORING
CAN2
RS232(1)
INTERFACEDISPLAY
RS232/RS485(2)
INTERFACE
USB 16 BINARY INPUTS
EXTENSION
MODULES
CAN1
POWER SUPPLY
8 TO 36 VDC+ -
CURRENTVO
LTAGE
16
ETHERNET
GENERATOR
DIESEL/GAS ENGINE
Starter
Fuel Solenoid
LOAD
1ph3ph3ph
Generator C. B. Control
1ph3ph
Mains C. B. Control
MAINS
414
I-LB
Protocol depends on ECU type
CAN J1939
Proprietary ECU coms.
(MDEC/M
TU, CCM/CAT, ...)
Proprietary ECU coms.
(MODBUS/CUMMINS, ...)
IG-IB
I-LB+
IGS-NT-LSM+PMS
OPTIONAL DONGLE: InteliVision 8
IS-NTC-BB + IV8
#32
IS-NTC-BB + IV8
#1
InteliVision 8#2InteliVision 8#3
InteliVision 8InteliVision 8
AVRi
21
3
3
21 ECU
SPEED GOVERNOR AVR
WebSupervisor
Integrated fixed and configurable protections
� 3 phase integrated generator protections (U + f) � IDMT overcurrent + Shortcurrent protection � Overload protection � Reverse power protection � Earth fault protection � 3 phase integrated mains protections (U + f) � Vector shift protection � All binary / analog inputs free configurable for
various protection types: HistRecOnly / Alarm Only / Alarm + History indication / Warning / Off load / Slow stop / BreakerOpen&Cooldown / Shutdown / Shutdown override / Mains protect / Sensor fail
� Phase rotation and phase sequence protection � Additional 160 programmable protections configurable for
any measured value to create customer specific protections � Application security
ANSI CODES
* can be created using universal protections
Features � 8” colour TFT display with
resolution of 800 × 600 pixels � Controlled by active buttons � Comes with new TRENDS monitoring screen � Windows CE operating system � Same language support as
InteliGenNT and InteliSysNT
� Screen configuration by customer export to XML format with subsequent manual screen modification and import back to the controller (as IS-Display)
� Intended for connection to ONE controller (InteliGenNT / InteliSysNT)
� The same dimensions as IS-Display / InteliSysNT (including cut out dimensions)
� Connection to a controller via RS232/485 and CAN bus
� Auto configuration based on controller application
� Designed to be mounted in both monitoring and engine room
� Operating temperature from -20 to +70° C (-4/158° F)
� CE, UL and ULC certification � Sealed to IP65
Benefits � Large, high-resolution screen � Colour TFT display � TRENDS monitoring screen � History columns’ features and adjustment � Simpler, faster and more comfortable control � More information in less time � Submenu navigation history � New password management interface � Same dimensions as IS-Display (InteliSysNT) � IS-NTC-BB can be mounted to the
rear side of InteliVision 8 � Plug and Play operation (auto configuration
based on controller application) � Universal solution for both controller
families – InteliGenNT / InteliSysNT
� Direct connection to the controller (converters are not needed)
Features � CHP support (programmable PID loops
and other built-in PLC functions) � Support of engines with ECU (J1939,
Modbus and other proprietary interfaces); alarm codes displayed in text form
� Automatic synchronizing and power control (via speed governor or ECU)
� Baseload, Import / Export, TempByPower � Peak shaving � Voltage and PF control (AVR) � Generator measurement: U, I, Hz,
kW, kVAr, kVA, PF, kWh, kVAhr � Mains measurement: U, I, Hz, kW, kVAr, PF � Selectable measurement ranges for AC voltages
and currents – 120 / 277 V, 0–1 / 0–5 A � Inputs and outputs confi gurable
for various customer needs � 1× RS232 / 2× RS485 interface with Modbus protocol
support; Analog / GSM / ISDN / CDMA modem communication support; SMS messages; ECU Modbus interface; secondary RS485 converter is isolated
� Event-based history (up to 4000 records) with customer-selectable list of stored values; RTC; statistic values
� Integrated PLC programmable functions � Interface to remote display units
(InteliVision 8, IS-Display) � USB 2.0 slave interface � Ethernet connection (RJ45) � Bipolar binary output – possibility to use
BO as High or Low side switch � Post mortem history (50 records)
Upgrade kits � IGS-NT-LSM + PMS dongle:• Enables multiple isolated parallel or multiple
parallel with mains operation (with CAN bus)• Digital load sharing• Digital VAr sharing• Optimizing number of running engines:
Power management; kW, kVA or % load based
DescriptionThe detachable modular construction (consisting of InteliSysNTC BaseBox and InteliVision 8 or InteliVision 5) allows easy installation with the potential for many different extension modules designed to suit individual customer requirements.
A built-in synchronizer and digital isochronous load sharer allow a total integrated solution for gen-sets in standby, island parallel or mains parallel. Native cooperation of up to 32 gen-sets is a standard feature.
InteliSysNT supports many standard ECU types and is specially designed to easily integrate to new versions.
New ethernet connections together with AirGate make remote internet connection to new InteliSysNT easy. After registration of InteliSysNT on our website you can simply monitor the site on the internet using new WebSupervisor.
ComAp can also provide customized firmware solutions to meet specific application requirements.
Schematic diagram
Communication modules and PC tools
� I-CR – CAN repeater module � IG-IB – Internet bridge � I-LB+ – Local bridge � InteliMonitor – PC monitoring tool � WebSupervisor – Web based system for
monitoring and controlling of ComAp controllers � GenConfig – PC configuration tool
Extension modules � I-CB – ECU communication bridge � up to 4× I-AOUT8 – Analog output extension module � up to 2× IGL-RA15 – Remote annunciator � up to 4× IGS-PTM – Analog/binary input/output module � up to 10× IS-AIN8 – Analog input module � up to 6× IS-BIN16/8 – Binary input/output module � up to 2× IGL-RA15 – Remote Annunciator
Remote diplays � up to 3× Intelivision 5 – Controller colour display unit � up to 6× Intelivision 8 – Controller colour display unit � up to 3× IS-Display – detachable display module
ANSI code Protection
59 Overvoltage
27 Undervoltage
47 Voltage asymmetry
81H Overfrequency
81L Underfrequency
50+51 Overcurrent
46 Current unbalance
32 Overload
ANSI code Protection
50N+64 Earth fault
32R Reverse power
25 Synchronism check
47 Phase rotation
37 Undercurrent*
55 Power factor*
71 Gas (fuel) level
DescriptionInteliVision 8 is a new generation colour display unit for either InteliGenNT / InteliSysNT or InteliMainsNT controllers. It is designed as a simple, easy to use Plug and Play solution and has been developed from our original IS-Display.
The new InteliVision 8 screen features many significant improvements such as the large high-resolution colour TFT display, which helps visibility and definition for onscreen information. The control interface has also been updated with user-friendly intuitive active buttons – giving users access to more information in less time. InteliVision 8 also features our unique TRENDS monitoring as a standard feature, helping you evaluate past events easily on one screen. The InteliVision 8 cut-out size is the same as the IS-Display (InteliSysNT), so InteliVision 8 can be easily used as a replacement for (or an alternative to) IS-Display. Regardless of the size it can be also used as a replacement for (or an alternative to) IG-Display LT GC or I-RD-CAN.
InteliVision 8 includes ComAp’s standard communication interface using RS232/485 and CAN bus communication. Designed to be mounted in both monitoring and engine room, InteliVision 8 gives complete access to all control functions when connected to InteliGenNT, InteliSysNT or InteliMainsNT controllers.
Intelivision 8InteliSysNTC BaseBox
New InteliSysNT New InteliSysNT New InteliSysNT
PC
PC
InteliVision 8#1
MODEMPC MODEM
IS-BIN16/8
IS-AIN8
I-CB/XX
IGS-PTM
IGL-RA15
I-CB/XX
I-AOUT8ENGINE
16 BINARY
OUTPUTS
(OPEN
COLLECTOR)
4 ANALOG
INPUTS
GENERATORMAINS
IS-NTC-BB
EARTH FAULT
CURRENT
CURRENTVO
LTAGE
SG O
UT
AVRi OUT
INTER-CONTROLLER
& MONITORING
CAN2
RS232(1)
INTERFACEDISPLAY
RS232/RS485(2)
INTERFACE
USB 16 BINARY INPUTS
EXTENSION
MODULES
CAN1
POWER SUPPLY
8 TO 36 VDC+ -
CURRENTVO
LTAGE
16
ETHERNET
GENERATOR
DIESEL/GAS ENGINE
Starter
Fuel Solenoid
LOAD
1ph3ph3ph
Generator C. B. Control
1ph3ph
Mains C. B. Control
MAINS
414
I-LB
Protocol depends on ECU type
CAN J1939
Proprietary ECU coms.
(MDEC/M
TU, CCM/CAT, ...)
Proprietary ECU coms.
(MODBUS/CUMMINS, ...)
IG-IB
I-LB+
IGS-NT-LSM+PMS
OPTIONAL DONGLE: InteliVision 8
IS-NTC-BB + IV8
#32
IS-NTC-BB + IV8
#1
InteliVision 8#2InteliVision 8#3
InteliVision 8InteliVision 8
AVRi
21
3
3
21 ECU
SPEED GOVERNOR AVR
WebSupervisor
Integrated fixed and configurable protections
� 3 phase integrated generator protections (U + f) � IDMT overcurrent + Shortcurrent protection � Overload protection � Reverse power protection � Earth fault protection � 3 phase integrated mains protections (U + f) � Vector shift protection � All binary / analog inputs free configurable for
various protection types: HistRecOnly / Alarm Only / Alarm + History indication / Warning / Off load / Slow stop / BreakerOpen&Cooldown / Shutdown / Shutdown override / Mains protect / Sensor fail
� Phase rotation and phase sequence protection � Additional 160 programmable protections configurable for
any measured value to create customer specific protections � Application security
ANSI CODES
* can be created using universal protections
Features � 8” colour TFT display with
resolution of 800 × 600 pixels � Controlled by active buttons � Comes with new TRENDS monitoring screen � Windows CE operating system � Same language support as
InteliGenNT and InteliSysNT
� Screen configuration by customer export to XML format with subsequent manual screen modification and import back to the controller (as IS-Display)
� Intended for connection to ONE controller (InteliGenNT / InteliSysNT)
� The same dimensions as IS-Display / InteliSysNT (including cut out dimensions)
� Connection to a controller via RS232/485 and CAN bus
� Auto configuration based on controller application
� Designed to be mounted in both monitoring and engine room
� Operating temperature from -20 to +70° C (-4/158° F)
� CE, UL and ULC certification � Sealed to IP65
Benefits � Large, high-resolution screen � Colour TFT display � TRENDS monitoring screen � History columns’ features and adjustment � Simpler, faster and more comfortable control � More information in less time � Submenu navigation history � New password management interface � Same dimensions as IS-Display (InteliSysNT) � IS-NTC-BB can be mounted to the
rear side of InteliVision 8 � Plug and Play operation (auto configuration
based on controller application) � Universal solution for both controller
families – InteliGenNT / InteliSysNT
� Direct connection to the controller (converters are not needed)
Features � CHP support (programmable PID loops
and other built-in PLC functions) � Support of engines with ECU (J1939,
Modbus and other proprietary interfaces); alarm codes displayed in text form
� Automatic synchronizing and power control (via speed governor or ECU)
� Baseload, Import / Export, TempByPower � Peak shaving � Voltage and PF control (AVR) � Generator measurement: U, I, Hz,
kW, kVAr, kVA, PF, kWh, kVAhr � Mains measurement: U, I, Hz, kW, kVAr, PF � Selectable measurement ranges for AC voltages
and currents – 120 / 277 V, 0–1 / 0–5 A � Inputs and outputs confi gurable
for various customer needs � 1× RS232 / 2× RS485 interface with Modbus protocol
support; Analog / GSM / ISDN / CDMA modem communication support; SMS messages; ECU Modbus interface; secondary RS485 converter is isolated
� Event-based history (up to 4000 records) with customer-selectable list of stored values; RTC; statistic values
� Integrated PLC programmable functions � Interface to remote display units
(InteliVision 8, IS-Display) � USB 2.0 slave interface � Ethernet connection (RJ45) � Bipolar binary output – possibility to use
BO as High or Low side switch � Post mortem history (50 records)
Upgrade kits � IGS-NT-LSM + PMS dongle:• Enables multiple isolated parallel or multiple
parallel with mains operation (with CAN bus)• Digital load sharing• Digital VAr sharing• Optimizing number of running engines:
Power management; kW, kVA or % load based
DescriptionThe detachable modular construction (consisting of InteliSysNTC BaseBox and InteliVision 8 or InteliVision 5) allows easy installation with the potential for many different extension modules designed to suit individual customer requirements.
A built-in synchronizer and digital isochronous load sharer allow a total integrated solution for gen-sets in standby, island parallel or mains parallel. Native cooperation of up to 32 gen-sets is a standard feature.
InteliSysNT supports many standard ECU types and is specially designed to easily integrate to new versions.
New ethernet connections together with AirGate make remote internet connection to new InteliSysNT easy. After registration of InteliSysNT on our website you can simply monitor the site on the internet using new WebSupervisor.
ComAp can also provide customized firmware solutions to meet specific application requirements.
Schematic diagram
Communication modules and PC tools
� I-CR – CAN repeater module � IG-IB – Internet bridge � I-LB+ – Local bridge � InteliMonitor – PC monitoring tool � WebSupervisor – Web based system for
monitoring and controlling of ComAp controllers � GenConfig – PC configuration tool
Extension modules � I-CB – ECU communication bridge � up to 4× I-AOUT8 – Analog output extension module � up to 2× IGL-RA15 – Remote annunciator � up to 4× IGS-PTM – Analog/binary input/output module � up to 10× IS-AIN8 – Analog input module � up to 6× IS-BIN16/8 – Binary input/output module � up to 2× IGL-RA15 – Remote Annunciator
Remote diplays � up to 3× Intelivision 5 – Controller colour display unit � up to 6× Intelivision 8 – Controller colour display unit � up to 3× IS-Display – detachable display module
ANSI code Protection
59 Overvoltage
27 Undervoltage
47 Voltage asymmetry
81H Overfrequency
81L Underfrequency
50+51 Overcurrent
46 Current unbalance
32 Overload
ANSI code Protection
50N+64 Earth fault
32R Reverse power
25 Synchronism check
47 Phase rotation
37 Undercurrent*
55 Power factor*
71 Gas (fuel) level
DescriptionInteliVision 8 is a new generation colour display unit for either InteliGenNT / InteliSysNT or InteliMainsNT controllers. It is designed as a simple, easy to use Plug and Play solution and has been developed from our original IS-Display.
The new InteliVision 8 screen features many significant improvements such as the large high-resolution colour TFT display, which helps visibility and definition for onscreen information. The control interface has also been updated with user-friendly intuitive active buttons – giving users access to more information in less time. InteliVision 8 also features our unique TRENDS monitoring as a standard feature, helping you evaluate past events easily on one screen. The InteliVision 8 cut-out size is the same as the IS-Display (InteliSysNT), so InteliVision 8 can be easily used as a replacement for (or an alternative to) IS-Display. Regardless of the size it can be also used as a replacement for (or an alternative to) IG-Display LT GC or I-RD-CAN.
InteliVision 8 includes ComAp’s standard communication interface using RS232/485 and CAN bus communication. Designed to be mounted in both monitoring and engine room, InteliVision 8 gives complete access to all control functions when connected to InteliGenNT, InteliSysNT or InteliMainsNT controllers.
Intelivision 8InteliSysNTC BaseBox
New InteliSysNT New InteliSysNT New InteliSysNT
PC
PC
InteliVision 8#1
MODEMPC MODEM
IS-BIN16/8
IS-AIN8
I-CB/XX
IGS-PTM
IGL-RA15
I-CB/XX
I-AOUT8ENGINE
16 BINARY
OUTPUTS
(OPEN
COLLECTOR)
4 ANALOG
INPUTS
GENERATORMAINS
IS-NTC-BB
EARTH FAULT
CURRENT
CURRENTVO
LTAGE
SG O
UT
AVRi OUT
INTER-CONTROLLER
& MONITORING
CAN2
RS232(1)
INTERFACEDISPLAY
RS232/RS485(2)
INTERFACE
USB 16 BINARY INPUTS
EXTENSION
MODULES
CAN1
POWER SUPPLY
8 TO 36 VDC+ -
CURRENTVO
LTAGE
16
ETHERNET
GENERATOR
DIESEL/GAS ENGINE
Starter
Fuel Solenoid
LOAD
1ph3ph3ph
Generator C. B. Control
1ph3ph
Mains C. B. Control
MAINS
414
I-LB
Protocol depends on ECU type
CAN J1939
Proprietary ECU coms.
(MDEC/M
TU, CCM/CAT, ...)
Proprietary ECU coms.
(MODBUS/CUMMINS, ...)
IG-IB
I-LB+
IGS-NT-LSM+PMS
OPTIONAL DONGLE: InteliVision 8
IS-NTC-BB + IV8
#32
IS-NTC-BB + IV8
#1
InteliVision 8#2InteliVision 8#3
InteliVision 8InteliVision 8
AVRi
21
3
3
21 ECU
SPEED GOVERNOR AVR
WebSupervisor
Integrated fixed and configurable protections
� 3 phase integrated generator protections (U + f) � IDMT overcurrent + Shortcurrent protection � Overload protection � Reverse power protection � Earth fault protection � 3 phase integrated mains protections (U + f) � Vector shift protection � All binary / analog inputs free configurable for
various protection types: HistRecOnly / Alarm Only / Alarm + History indication / Warning / Off load / Slow stop / BreakerOpen&Cooldown / Shutdown / Shutdown override / Mains protect / Sensor fail
� Phase rotation and phase sequence protection � Additional 160 programmable protections configurable for
any measured value to create customer specific protections � Application security
ANSI CODES
* can be created using universal protections
Features � 8” colour TFT display with
resolution of 800 × 600 pixels � Controlled by active buttons � Comes with new TRENDS monitoring screen � Windows CE operating system � Same language support as
InteliGenNT and InteliSysNT
� Screen configuration by customer export to XML format with subsequent manual screen modification and import back to the controller (as IS-Display)
� Intended for connection to ONE controller (InteliGenNT / InteliSysNT)
� The same dimensions as IS-Display / InteliSysNT (including cut out dimensions)
� Connection to a controller via RS232/485 and CAN bus
� Auto configuration based on controller application
� Designed to be mounted in both monitoring and engine room
� Operating temperature from -20 to +70° C (-4/158° F)
� CE, UL and ULC certification � Sealed to IP65
Benefits � Large, high-resolution screen � Colour TFT display � TRENDS monitoring screen � History columns’ features and adjustment � Simpler, faster and more comfortable control � More information in less time � Submenu navigation history � New password management interface � Same dimensions as IS-Display (InteliSysNT) � IS-NTC-BB can be mounted to the
rear side of InteliVision 8 � Plug and Play operation (auto configuration
based on controller application) � Universal solution for both controller
families – InteliGenNT / InteliSysNT
� Direct connection to the controller (converters are not needed)
Features � CHP support (programmable PID loops
and other built-in PLC functions) � Support of engines with ECU (J1939,
Modbus and other proprietary interfaces); alarm codes displayed in text form
� Automatic synchronizing and power control (via speed governor or ECU)
� Baseload, Import / Export, TempByPower � Peak shaving � Voltage and PF control (AVR) � Generator measurement: U, I, Hz,
kW, kVAr, kVA, PF, kWh, kVAhr � Mains measurement: U, I, Hz, kW, kVAr, PF � Selectable measurement ranges for AC voltages
and currents – 120 / 277 V, 0–1 / 0–5 A � Inputs and outputs confi gurable
for various customer needs � 1× RS232 / 2× RS485 interface with Modbus protocol
support; Analog / GSM / ISDN / CDMA modem communication support; SMS messages; ECU Modbus interface; secondary RS485 converter is isolated
� Event-based history (up to 4000 records) with customer-selectable list of stored values; RTC; statistic values
� Integrated PLC programmable functions � Interface to remote display units
(InteliVision 8, IS-Display) � USB 2.0 slave interface � Ethernet connection (RJ45) � Bipolar binary output – possibility to use
BO as High or Low side switch � Post mortem history (50 records)
Upgrade kits � IGS-NT-LSM + PMS dongle:• Enables multiple isolated parallel or multiple
parallel with mains operation (with CAN bus)• Digital load sharing• Digital VAr sharing• Optimizing number of running engines:
Power management; kW, kVA or % load based
DescriptionThe detachable modular construction (consisting of InteliSysNTC BaseBox and InteliVision 8 or InteliVision 5) allows easy installation with the potential for many different extension modules designed to suit individual customer requirements.
A built-in synchronizer and digital isochronous load sharer allow a total integrated solution for gen-sets in standby, island parallel or mains parallel. Native cooperation of up to 32 gen-sets is a standard feature.
InteliSysNT supports many standard ECU types and is specially designed to easily integrate to new versions.
New ethernet connections together with AirGate make remote internet connection to new InteliSysNT easy. After registration of InteliSysNT on our website you can simply monitor the site on the internet using new WebSupervisor.
ComAp can also provide customized firmware solutions to meet specific application requirements.
Schematic diagram
Communication modules and PC tools
� I-CR – CAN repeater module � IG-IB – Internet bridge � I-LB+ – Local bridge � InteliMonitor – PC monitoring tool � WebSupervisor – Web based system for
monitoring and controlling of ComAp controllers � GenConfig – PC configuration tool
Extension modules � I-CB – ECU communication bridge � up to 4× I-AOUT8 – Analog output extension module � up to 2× IGL-RA15 – Remote annunciator � up to 4× IGS-PTM – Analog/binary input/output module � up to 10× IS-AIN8 – Analog input module � up to 6× IS-BIN16/8 – Binary input/output module � up to 2× IGL-RA15 – Remote Annunciator
Remote diplays � up to 3× Intelivision 5 – Controller colour display unit � up to 6× Intelivision 8 – Controller colour display unit � up to 3× IS-Display – detachable display module
ANSI code Protection
59 Overvoltage
27 Undervoltage
47 Voltage asymmetry
81H Overfrequency
81L Underfrequency
50+51 Overcurrent
46 Current unbalance
32 Overload
ANSI code Protection
50N+64 Earth fault
32R Reverse power
25 Synchronism check
47 Phase rotation
37 Undercurrent*
55 Power factor*
71 Gas (fuel) level
DescriptionInteliVision 8 is a new generation colour display unit for either InteliGenNT / InteliSysNT or InteliMainsNT controllers. It is designed as a simple, easy to use Plug and Play solution and has been developed from our original IS-Display.
The new InteliVision 8 screen features many significant improvements such as the large high-resolution colour TFT display, which helps visibility and definition for onscreen information. The control interface has also been updated with user-friendly intuitive active buttons – giving users access to more information in less time. InteliVision 8 also features our unique TRENDS monitoring as a standard feature, helping you evaluate past events easily on one screen. The InteliVision 8 cut-out size is the same as the IS-Display (InteliSysNT), so InteliVision 8 can be easily used as a replacement for (or an alternative to) IS-Display. Regardless of the size it can be also used as a replacement for (or an alternative to) IG-Display LT GC or I-RD-CAN.
InteliVision 8 includes ComAp’s standard communication interface using RS232/485 and CAN bus communication. Designed to be mounted in both monitoring and engine room, InteliVision 8 gives complete access to all control functions when connected to InteliGenNT, InteliSysNT or InteliMainsNT controllers.
New InteliSysNT
PREMIUM AND COGENERATION GEN–sET CONTROllER
ComAp is a member of AMPS (The Association of Manufacturers of Power generating Systems).
Selected ComAp products have the UL Certification.
ComAp products meet the highest standards, with every stage of production undertaken in accordance with the ISO certification obtained in 1998.
TWO UNIT SYSTEM BaseBox + DisplayInteliSysNT BaseBox and InteliVision 8
New InteliSysNT RELATED PRODUCTS Worldwide references
GCB #3
CGCB
J1939
GCB #1
MAINS #1
MASTER
SELECTOR
FEEDBACK
MASTER
SELECTOR
MCB #1
MAN 1, 2, 3
GCB #2
MAINS #2
MCB #2
MAINS #3
MCB #3
MainsPro
MainsPro
MainsPro
MCB
GCB
1, 2, 3
PLC
POWER CONTROL
CENTER
IS-NT-BB
IV 8
MexicoGenerator room at Hotel Sandos, Quintana Roo
The first InteliVision units operating in Mexico are installed in a prestigious hotel Sandos close to the famous Riviera Maya beach area.
“The staff on site were delighted how easy and quick it was to inspect the gen-set using the new large colourful screens on the InteliVision unit, and the benefits provided by new features, especially trends reporting.”
Agustin de Jesus Garcia PastranaDupont Elektric Mexico Technician
SwitzerlandShunting loco at Holcim cement factory
The shunting locomotive re-power application uses an InteliDrive Mobile for the complete control, monitoring and protection of the Volvo D16 engine which drive a Voith Hydro – Turbo gear-box for propulsion via a systemof push-rods.
Full communication between engine, ID-Mobile and the two InteliVision displays is achievedwith J1939 CAN bus – making the system wiring and integration very simple.All values, warnings and fault codes from the engine (EMS) are displayed on the two large InteliVision displays, located on both sides of the locomotive cabin.
CANADAParalleling system for Oil sand camp
“When I first saw InteliVision at PowerGen, I immediately recognised its potential for our power generation systems. The large easy to read colour display and customer-friendly interactivity is precisely what our customers have been looking for. We have already installed systems with InteliVision and received very positive feedback from our customers on the units performance.”
Santokh Sahota P. Eng Simson MaxwellEngineering Manager
USACompressor applications
“With the introduction of the InteliVision and our usage of ComAp hardware we now have a whole new market to pursue through the introduction of our own brand of compressor control panel. The ComAp hardware allows us to be fully Modbus capable and it integrates well with the engine manufactures controls.”
Dale ShowsSEC EnergyProducts & Services
IG-NT-BB
InteliVision 5 InteliVision 5
DescriptionInteliSysNT is an expandable controller for both single and multiple gen-sets operating in standby or parallel modes, especially in cogeneration (CHP) and other complex applications.
InteliVision 8 is a new generation colour display unit for either InteliGenNT, InteliSysNT, InteliMainsNT or InteliDrive controllers. It is designed as a simple, easy to use Plug and Play solution, which also features our unique TRENDS monitoring as a standard feature.
Benefits � Support of engines with ECU
(Electronic Control Unit) � Excellent configurability to match
customers’ needs exactly � Complete integrated gen-set
solution and signal sharing via CAN bus – minimum external components needed
� Many communication options – easy remote supervising and servicing
� Perfect price / performance ratio � Gen-set performance log for
easy problem tracing � Built-in PLC � 8” Colour TFT display � Active buttons – fast access
to important data � Trends � InteliVision 8 is possible to
connect via RS 232/485, CAN � Plug and play system � Sealed to IP65AirGate
Modern communications made simple. ComAp’s powerful AirGate technology is provided in a range of our controllers and makes remote internet connection to the ComAp controller easy.Just register the AirGate enabled controller on our website and from then on let ComAp’s uniquesystem locate and maintain contact with the controller, no need to worry about VPN’s, Static IPaddresses or corporate firewalls, simple! “AirGate – Simply connected.”
Features and specification are subject to change without prior notice 2010-11/CPLEISV8
ComAp, spol. s r. o.Czech RepublicPhone: + 420 246 012 111 Fax: + 420 266 316 647E-mail: [email protected]: www.comap.cz
MANuFACTurEr: LoCAL DISTrIBuTor / PArTNEr:
Customer satisfaction is our mission. We continuously develop the best people to succeed in our mission.
New InteliMainsNT
MAINs sUPERvIsION CONTROllER
� New InteliMainsNT is designed for multiple (up to 31) gen-sets operating in parallel to mains. New InteliMainsNT controller connects the group of gen-sets to the mains. It can serve as a bus-tie synchronizing controller between two groups of gen-sets.
� New InteliMainsNT: IM-NT-BB + InteliVision 5
HW modifications
Typical application
MULTIPLE LOADS – SEvERAL MAINS SUPPLIESDescription:
� In case of manipulation, the system switches from one branch to another by turning of the Master Selector Switch (MSS): BO MSS turn is used to turn the MSS.
� The mains voltage measurement, generator current measurement, MCB and GCB feedbacks, MCB and GCB control signals and Mains Failure (MF) signals (MainsPro outputs) are switched by the MSS, so that the system continuously ”sees” only the selected branch.
� MCB and GCB are operated by pulse signal (GCB open/close, MCB close). The pulse is issued as a request for CB operation and terminated at the moment of corresponding feedback receipt.
� The MainsPro relays monitor mains on all 3 branches. In case of any MF, the gen-set is started. � In case of MF on any branch, the proper MainsPro opens MCB, MSS switches to the failed branch and closes GCB. � If a MF occurs on a different branch at the same moment, the controller finishes manipulation
of GCB, MSS switches to a different branch and closes the other GCB. � After an existing MF state terminates on any branch, the MSS turns to this branch,
InteliSysNT reverse-synchronizes and closes MCB and opens GCB. Short-time parallel is allowed on the current branch.
� The MSS is blocked from moving away from a branch, where: – parallel operation is in effect – GCB open/close or MCB close signals are active – MF signal is in effect and GCB is open
� In case that all existing MF are solved and all GCB’s are open, the gen-set stops.
scope of supply:
� 1× PLC (not delivered by ComAp) � 1× Motorized rotary switch with
3× 16 contacts (not delivered by ComAp) � 1× InteliSysNTC BaseBox � 1× InteliVision 8 � 3× MainsPro � 1× IG-AVRi � 1× IG-AVRi-TRANS/LV
InteliGenNT ColourAll IN ONE GEN-sET CONTROllER
� InteliGenNT Colour is a comprehensive controller for both single and multiple gen-sets operating in standby or parallel modes.
� InteliGenNT Colour: IG-NT-BB + InteliVision 5
IM-NT-BB
Base box Display Brief info
IS-NTC-BB InteliVision 5 Control unit with detachable colour display
IS-NTC-BB InteliVision 8 Control unit with detachable colour display
New InteliSysNT
PREMIUM AND COGENERATION GEN–sET CONTROllER
ComAp is a member of AMPS (The Association of Manufacturers of Power generating Systems).
Selected ComAp products have the UL Certification.
ComAp products meet the highest standards, with every stage of production undertaken in accordance with the ISO certification obtained in 1998.
TWO UNIT SYSTEM BaseBox + DisplayInteliSysNT BaseBox and InteliVision 8
New InteliSysNT RELATED PRODUCTS Worldwide references
GCB #3
CGCB
J1939
GCB #1
MAINS #1
MASTER
SELECTOR
FEEDBACK
MASTER
SELECTOR
MCB #1
MAN 1, 2, 3
GCB #2
MAINS #2
MCB #2
MAINS #3
MCB #3
MainsPro
MainsPro
MainsPro
MCB
GCB
1, 2, 3
PLC
POWER CONTROL
CENTER
IS-NT-BB
IV 8
MexicoGenerator room at Hotel Sandos, Quintana Roo
The first InteliVision units operating in Mexico are installed in a prestigious hotel Sandos close to the famous Riviera Maya beach area.
“The staff on site were delighted how easy and quick it was to inspect the gen-set using the new large colourful screens on the InteliVision unit, and the benefits provided by new features, especially trends reporting.”
Agustin de Jesus Garcia PastranaDupont Elektric Mexico Technician
SwitzerlandShunting loco at Holcim cement factory
The shunting locomotive re-power application uses an InteliDrive Mobile for the complete control, monitoring and protection of the Volvo D16 engine which drive a Voith Hydro – Turbo gear-box for propulsion via a systemof push-rods.
Full communication between engine, ID-Mobile and the two InteliVision displays is achievedwith J1939 CAN bus – making the system wiring and integration very simple.All values, warnings and fault codes from the engine (EMS) are displayed on the two large InteliVision displays, located on both sides of the locomotive cabin.
CANADAParalleling system for Oil sand camp
“When I first saw InteliVision at PowerGen, I immediately recognised its potential for our power generation systems. The large easy to read colour display and customer-friendly interactivity is precisely what our customers have been looking for. We have already installed systems with InteliVision and received very positive feedback from our customers on the units performance.”
Santokh Sahota P. Eng Simson MaxwellEngineering Manager
USACompressor applications
“With the introduction of the InteliVision and our usage of ComAp hardware we now have a whole new market to pursue through the introduction of our own brand of compressor control panel. The ComAp hardware allows us to be fully Modbus capable and it integrates well with the engine manufactures controls.”
Dale ShowsSEC EnergyProducts & Services
IG-NT-BB
InteliVision 5 InteliVision 5
DescriptionInteliSysNT is an expandable controller for both single and multiple gen-sets operating in standby or parallel modes, especially in cogeneration (CHP) and other complex applications.
InteliVision 8 is a new generation colour display unit for either InteliGenNT, InteliSysNT, InteliMainsNT or InteliDrive controllers. It is designed as a simple, easy to use Plug and Play solution, which also features our unique TRENDS monitoring as a standard feature.
Benefits � Support of engines with ECU
(Electronic Control Unit) � Excellent configurability to match
customers’ needs exactly � Complete integrated gen-set
solution and signal sharing via CAN bus – minimum external components needed
� Many communication options – easy remote supervising and servicing
� Perfect price / performance ratio � Gen-set performance log for
easy problem tracing � Built-in PLC � 8” Colour TFT display � Active buttons – fast access
to important data � Trends � InteliVision 8 is possible to
connect via RS 232/485, CAN � Plug and play system � Sealed to IP65AirGate
Modern communications made simple. ComAp’s powerful AirGate technology is provided in a range of our controllers and makes remote internet connection to the ComAp controller easy.Just register the AirGate enabled controller on our website and from then on let ComAp’s uniquesystem locate and maintain contact with the controller, no need to worry about VPN’s, Static IPaddresses or corporate firewalls, simple! “AirGate – Simply connected.”
Features and specification are subject to change without prior notice 2010-11/CPLEISV8
ComAp, spol. s r. o.Czech RepublicPhone: + 420 246 012 111 Fax: + 420 266 316 647E-mail: [email protected]: www.comap.cz
MANuFACTurEr: LoCAL DISTrIBuTor / PArTNEr:
Customer satisfaction is our mission. We continuously develop the best people to succeed in our mission.
New InteliMainsNT
MAINs sUPERvIsION CONTROllER
� New InteliMainsNT is designed for multiple (up to 31) gen-sets operating in parallel to mains. New InteliMainsNT controller connects the group of gen-sets to the mains. It can serve as a bus-tie synchronizing controller between two groups of gen-sets.
� New InteliMainsNT: IM-NT-BB + InteliVision 5
HW modifications
Typical application
MULTIPLE LOADS – SEvERAL MAINS SUPPLIESDescription:
� In case of manipulation, the system switches from one branch to another by turning of the Master Selector Switch (MSS): BO MSS turn is used to turn the MSS.
� The mains voltage measurement, generator current measurement, MCB and GCB feedbacks, MCB and GCB control signals and Mains Failure (MF) signals (MainsPro outputs) are switched by the MSS, so that the system continuously ”sees” only the selected branch.
� MCB and GCB are operated by pulse signal (GCB open/close, MCB close). The pulse is issued as a request for CB operation and terminated at the moment of corresponding feedback receipt.
� The MainsPro relays monitor mains on all 3 branches. In case of any MF, the gen-set is started. � In case of MF on any branch, the proper MainsPro opens MCB, MSS switches to the failed branch and closes GCB. � If a MF occurs on a different branch at the same moment, the controller finishes manipulation
of GCB, MSS switches to a different branch and closes the other GCB. � After an existing MF state terminates on any branch, the MSS turns to this branch,
InteliSysNT reverse-synchronizes and closes MCB and opens GCB. Short-time parallel is allowed on the current branch.
� The MSS is blocked from moving away from a branch, where: – parallel operation is in effect – GCB open/close or MCB close signals are active – MF signal is in effect and GCB is open
� In case that all existing MF are solved and all GCB’s are open, the gen-set stops.
scope of supply:
� 1× PLC (not delivered by ComAp) � 1× Motorized rotary switch with
3× 16 contacts (not delivered by ComAp) � 1× InteliSysNTC BaseBox � 1× InteliVision 8 � 3× MainsPro � 1× IG-AVRi � 1× IG-AVRi-TRANS/LV
InteliGenNT ColourAll IN ONE GEN-sET CONTROllER
� InteliGenNT Colour is a comprehensive controller for both single and multiple gen-sets operating in standby or parallel modes.
� InteliGenNT Colour: IG-NT-BB + InteliVision 5
IM-NT-BB
Base box Display Brief info
IS-NTC-BB InteliVision 5 Control unit with detachable colour display
IS-NTC-BB InteliVision 8 Control unit with detachable colour display