W.O. # _____________________________________________DATE _______________________________________________MODEL ____________________________________________TECHNICIAN SIGNATURE ______________________________P.I.N. _________________________ HOURS ______________

CUSTOMER NAME ____________________________________ ADDRESS ___________________________________________CITY, STATE, ZIP _____________________________________ PHONE _____________________________________________CUSTOMER SIGNATURE _______________________________

CR ROTARY COMBINE INSPECTION

PM-14365Rev 6/08

NEW HOLLAND MAINTENANCE INSPECTION CHECKLISTITEM # COMMENTS

Safety equipment1. Seat Belt2. Warning/flashers, turn signals,

beacons3. Decals, SMV4. Horn, back-up alarm5. Brake pedal interlock6. Feeder lift safety lock7. All shields in place8. Reflectors9. Mirrors

feeder HouSing10. Feeder drum, stops, pivots,

bearings, and seal11. Feeder chain, slats, and links12. Feeder chain tension13. Upper sprockets, strippers,

and bearings14. Slip clutch condition and

adjustment15. Feeder drive belt/pulleys and

chain/sprockets16. Header jackshaft belt, pulley,

and bearings17. Feeder housing floor condition18. Feeder door seal19. Feeder reverser condition/

operation20. Stone ejector trap door operation/

adjustment21. Stone ejector warning operation

rotor aSSembly22. Front bearings and infeed castings23. Rotor auger wear lugs24. Straight rasp bars25. Rear rotor area fins26. Thresher clutch adjustment27. Torque sensing unit and rotor belt28. Rotor speed adjuster29. Rotor drive coupler chain &

sprocket condition30. Rotor gearbox coupler sprocket &

chain condition

rotor Cage, ConCaveS, and grateS31. Concaves/grates – damage32. Concave clearance/adjustment33. Rotor covers – cracks, distortion,

and wear34. Separator grates – damage-wear35. Electric concave adjustment

CHaffer and SHoe SieveS36. Cracks/warpage/misalignment37. Hanger bushings38. Shaker drive bearings, belts

and pulleys39. Front and side seals40. Grain pan condition41. Electric sieve adjustment42. Self-leveling cleaning shoe

movement, actuator, rollers, and pivot

Cleaning fan43. Drive belts, pulleys and bearings44. Fan blades – cracked45. Drive pulley – wear, not loose46. Variable hub (clean) and

thrust bearing

diSCHarge beater47. Drive belt, pulleys, and tensioner48. Hubs, shaft, and bearings49. Grate-cracks, wear, and pan

adjustment

grain/tailingS augerS/elevatorS 50. Clean grain auger trough –

damage51. Auger flights – cracks, bending52. Shoe drive gearboxes, shafts,

belts, & couplers53. Clean grain elevator chain,

paddles, & sprockets54. Clean grain elevator bearings,

drive chain, and drive sprockets55. Clean grain elevator head & boot

condition56. Tailings return elevator flights,

sprockets, paddles, and chain adjustment

57. Tailings return elevator bearings58. Tailings return elevator head59. Tailings return upper auger

and tube60. Tailings return elevator jackshaft

drive belt61. Tailings elevator drive chain

grain/tailingS augerS/elevatorS (Cont.)62. Locking collars, drive hubs, and

setscrews63. Slip clutch – wear and adjustment64. Bubble-up auger and tube

condition

grain tank and unloading SyStem65. Unloading drive sprockets/belts/

chains/bearings66. Gear box bearings, couplers,

and gears67. Augers, flighting, and bearings68. Pivot movement and wear69. Grain tank – leaks

Straw CHopper, CHaff Spreader70. Worn/missing spreader bats

and paddles71. Drive belt, pulleys, and tensioner72. Spreader drives73. Drive shaft bearings74. Hub, shaft, and bearings75. Chopper knife and hardware

condition76. Stationary knives broken77. Chopper infeed mechanism

A B C S A B C S A B C SA B C S

A CrITICAL – MuST rEPAIr

B OPErATIONAL – SIgNS Of WEAr

C OK

S PASSED INSPECTION - SErvICE PrOvIDED

This information is only for the purpose of suggesting possible repair or treatment of equipment. Any remedy will be limited to the amount of the inspection fee. Dealer makes no expressed or implied warranties, and disclaims any incidental or consequential damages.

1 of 2

W.O. # _____________________________________________DATE _______________________________________________MODEL ____________________________________________TECHNICIAN SIGNATURE ______________________________P.I.N. _________________________ HOURS ______________

CUSTOMER NAME ____________________________________ ADDRESS ___________________________________________CITY, STATE, ZIP _____________________________________ PHONE _____________________________________________CUSTOMER SIGNATURE _______________________________

CR ROTARY COMBINE INSPECTION

PM-14365Rev 6/08

NEW HOLLAND MAINTENANCE INSPECTION CHECKLISTITEM # COMMENTS

engine78. Coolant level, protection level _________°79. Radiator cap/recovery bottle80. Water pump, bearings, fan condition81. Radiator fan drive bearings condition82. Hoses and connections83. Fuel leaks84. Oil leaks, engine front/rear/head gasket leaks85. Radiator, oil cooler, A/C condenser, rotary air screen-clean86. Air leaks, seal at rotary screen door, radiator, and inner vane87. Fuel tank, fuel cap condition, fuel filter88. Drain fuel system water separator89. High idle/low idle90. Turbo, oil seepage, missing vanes91. Air cleaner, dents, seals, aspirator obstructions92. Air cleaner outer and inner filter element93. Air restriction indicator94. Manifold and muffler leaks/cracks95. Belts – wear/tension/alignment96. Damper pulley condition97. Crankcase breather filter – inspect/ replace

HydrauliC SyStem98. Leaks: fittings, hoses, rod seals, packings99. Valves for proper operation100. Pump drive and hoses101. Pump mounting

HydroStatiC drive102. Propulsion control lever friction

adjustment103. Drive couplings and hoses104. Final drive bolts at axle, loose/

broken105. Final drive axle bearing free play106. Final drive seal condition107. Functional: shifting108. Functional: turn brakes109. Functional: park brake110. Functional: hydrostatic drive111. Functional: rear wheel assist

wHeelS/powered rear axle (pra)112. Rear axle torque hub leaks113. Front/rear tire inflation114. Rear wheel toe-in115. Rear axle pivot wear/cracks116. Wheel bolt torque

eleCtriCal SyStem117. Battery voltage tested ____ volts118. Battery water level (or sealed)119. Battery posts, cables and

clamps/clean

eleCtriCal SyStem (Cont.)120. Charging system tested

____ volts.121. Field and road lights122. All instruments/gauges &

warning indicators123. Neutral start switch & starter

operation124. Heater/air conditioning125. Electric fuel pump126. Error codes127. Header lift/tilt128. Reel lift/fore/aft129. Header tilt function130. Unloader swing and engage131. Feeder reverser132. Shaft speed monitor133. Grain loss monitor134. Wiring harness condition

lubriCation levelS135. Engine oil136. Transmission oil137. Hydraulic138. Brake fluid139. Final drives140. Hydraulic reverser141. PRA gear case142. Engine gearbox143. Rotor gearboxes

miSCellaneouS144. External condition145. Operator’s seat146. Radio147. Operator’s manual148. Fire extinguiser149. Grain flow sensor – clean and inspect150. Grain moisture sensor – clean and inspect151. Other:_____________________152. Other:_____________________

additional maintenanCe153. Engine valve lash adjustment (if required)154. Fuel injectors condition/ pop-off pressure155. Lubricate grease points156. Filters: fuel, hydraulic/hydrostatic, coolant, HVAC157. HVAC system function

fluid analySiS (optional)158. Engine159. Hydraulic oil160. Final drives161. Coolant162. Engine and rotor gearboxes

A B C S A B C S A B C S A B C S

This information is only for the purpose of suggesting possible repair or treatment of equipment. Any remedy will be limited to the amount of the inspection fee. Dealer makes no expressed or implied warranties, and disclaims any incidental or consequential damages.

A CrITICAL – MuST rEPAIr

B OPErATIONAL – SIgNS Of WEAr

C OK

S PASSED INSPECTION - SErvICE PrOvIDED

2 of 2