Network Master Gigabit Ethernet tester Sales Introduction ... · Network Master Gigabit Ethernet...
Transcript of Network Master Gigabit Ethernet tester Sales Introduction ... · Network Master Gigabit Ethernet...
Slide 1
Network Master Gigabit Ethernet Tester
Network Master Gigabit Ethernet Tester
IntroductionByOle SørensenProduct manager
Slide 2
Network Master Gigabit Ethernet Tester
Important Technology BackgroundThe market for GigE Installation and Maintenance testers is growing 20% annually.
The market drivers are networkmigration from PDH/SDH to IP and high growth of VoIP, IPTV and data servicesNew adoption of mobile network wire line backhaul services is one more driver for rapid growth of Ethernet deployments As Ethernet is becoming a standard transport media the market is now demanding high quantities of low cost dedicated GigE test equipment for basic Ethernet installation and maintenance as supplement to all-in-one-box testers
Slide 3
Network Master Gigabit Ethernet Tester
Why Users Need the NM GigE TesterOut-of-service testing
Installation and commissioning of new Ethernet linesOperators normally verify quality/performance of new lines before they are taken into operationRFC 2544 defines tests describing the performance characteristics of these lines.RFC 2544 is typically used for bringing into service
Easily test the quality of a communication lineLoop back the NM GigE test signal using a cable or special configuration at the far end
Line under testRx
Tx
EthernetNetwork
Slide 4
Network Master Gigabit Ethernet Tester
Line under testRx
Tx
EthernetNetwork
Why Users Need the NM GigE TesterEthernet Multistream testing is important:
By sending several streams of traffic with different priority the user can verify that high priority traffic is transported better (i.e. has lower frame loss ratio) through a congested network than low priority traffic.VoIP traffic is often given a high priority in order to ensure the quality of the service
VLAN tag priority may be used to give high priorityDSCP/TOS byte may be used to give high priorityTCP/UDP port numbers may be used to give high priority
Slide 5
Network Master Gigabit Ethernet Tester
In-service analysis with pass through modeLive system troubleshooting
E.g. transmission errors seen for both sides of the line simultaneouslyBi-directional analysis gives best problem resolution
Monitoring both directions of the line simultaneouslyLive system transmission performance analysis
Bi-directional analysis monitors performance properlyEnsure that traffic runs smoothly both ways
Why Users Need NM GigE Tester
Slide 6
Network Master Gigabit Ethernet Tester
Why Users Need NM GigE TesterFar end loop back is required for for applications like:
Installation and commissioning testing.QoS verification End-to-end testing
Instrument in reflector mode
Line under testRx
TxEthernetNetwork
Tx
Rx
Instrument in reflector mode
Slide 7
Network Master Gigabit Ethernet Tester
Key Features to RememberCompact and handy - Perfect solution for installation and commissioning of Ethernet links
Easy to useLarge color screenTest Automator- makes it very easy for the field technician to make repeated sequences of tests
Electrical cable testPing testThroughput, frame loss, latency and packet jitter verification (RFC2544 option)End-to-end test (RFC2544 option)BER testingTraffic generation and receptionMultiple stream test (option)Document measurements with PDF reports
Slide 8
Network Master Gigabit Ethernet Tester
Key Features to Remember Designed for highly portable field use.Easily held with one hand
Palm-size (190 x 96 x 48 mm)Approximately 2 lbs (800g)
Battery operated2 hours typical, 4 hour recharge
Quick start upStart up in approx. 15 seconds
RuggedSealed design – no vents or fans
Color indoor/outdoor display standard4.3” high resolutionLarge display compared to the size of the instrument
Slide 9
Network Master Gigabit Ethernet Tester
Key Features to RememberCost-effective installation and maintenance tool
Soft case, manual, charger, battery are standardComplete Ethernet tester with attractive price
User configurable (modular) platform3 configurationsOptional SFP modulesSW option: RFC2544 testSW option: Multistream
Complete data managementInternal storage of resultsEasy “drag and drop” transfers to PCReporting in pdf format
Mainframe
Gigabit Ethernet test module
Slide 10
Network Master Gigabit Ethernet Tester
3 Models Concept.
MU909060A1Ports:
1xRJ45,1x SFP
Highlights:- For mixed networks
(Optical and Electrical interfaces)
- Cost effective
MU909060A2Ports:
2xRJ45
Highlights:- Electrical interfaces
only
MU909060A3Ports:
2xSFP
Highlights:- Optical and Electrical
interfaces
Slide 11
Network Master Gigabit Ethernet Tester
Key Features to RememberInterfaces
10/100/1000 Mbps Electrical, 100/1000 Mbps OpticalFDX / HDX (10/100 El.)
ModesEthernet – general Ethernet testerReflector – act as loop-back device for another testerPass Through mode – live traffic analysis
EncapsulationsEtherType II (DIX v.2), IEEE 802.3 with 802.2(LLC1), IEEE 802.3 with SNAP
VLAN taggingConfigurable Ethernet (MAC) and IP source and destination addresses (supports IPv4 and IPv6), UDP/TCP port numbers and DSCP/TOS byte
Slide 12
Network Master Gigabit Ethernet Tester
Product Positioning
The Network Master Gigabit Ethernet tester (MT9090A / MU909060A1/A2/A3) is a small, light and cost-effective Gigabit Ethernet tester for field technicians installing, commissioning,and troubleshooting Ethernet links. With the instruments Test
Automator the technician can quickly and reliably test and verify Ethernet links.