~X~L~’ ~L~\~NDALGALlON MANUFACTURING COMPANY, Gallon, OhIo 44833, U.S.A.a Jeffrey Gallon inc. Company

CONVERTER OUTPUT SHAFT GOVERNOR

The instructions in this section basically apply to all governorsused on Galion Grade-O-Matic graders and Roll—O-Matic rollers

Adjustment of governor to engine fuel systemthe unit operator’s manual.

procedure is found in

Lubricating instructions for governors not having pressure lubesupply are found in the unit operator’s manual.

CONTENTS

Disassembly 1—7

Assembly 7 - 13

ROLfE~[

3/74~

PAGE

‘U

fF

• FILE: t.SECTION: .i_

1 Disassembly

Remove adjusting screw eye lock nut (1),adjusting screw eye (2), and governor spring (3).

2

Remove speed change shaft snapring and washer.

3

Remove speed change lever and shaft andspeed change spring lever as an assembly.

N’

1

1338

1339

1340

MANUAL aaC

3

2

FILE: ~SECTION: .L. SHOP I, MANUAL

4

Remove speed change bracket.

CE

5

Remove throttle lever roll pin.

Remove throttle lever from rocker shaft.

6

Remove spring lever roll pin.

1341

134Z

Remove lever from rocker shaft.

2

-c~

I ,7....W.*%

1

Remove four body-to-base attaching screws.

Remove body and gasket (1) from base.

8

I

o

~ a.ç

J4I1344

Remove capscrews from rocker yoke (1).

Remove yoke from body.

9 1.345

Remove oil seal.

B~y seal consists of two parts--a metalbackup washer and a neoprene seal.

•:j :l~

1346

FILE: 1-...SECTION: L SHOP

7

e MANUAL

1

I

3

Remove bumper screw from body.

4

1349 C7--

SECTION: ± SHOP MANUALC

1347

10

Remove snapring from rocker shaft.

11

Move shaft through bearing and body.

Bearing, seal, and snapring at oppositeend of shaft will remain on shaft.

12

Oo~

1348

~iI A XTYT A IItlAfl U IlL Ia

13

Examine body bushing for wear.

Do not remov& bushing unless replacementis needed.

14

Remove thrust sleeve and bearing from spiderand shaft assembly.

15

Remove thrust bearing from thrust sleeve.

135(

1351

1352

FILE: t...SECTION: ± SHOP

I

5

:J. FILE:_L.SECTION: t

16

SHOP MANUAL —a

Remove weight pin clips (1) from weightpins (2).

NOTE: Weight pins are knurled at one end onlyand clips should be removed from end oppositethe knurling.

17

Remove pins and weights from spider andshaft assembly.

18

U;;a ill

1353

1354

C:

Remove drive shaft snapring.

Use Waldes-Truarc pliers #2 or equal.

135C

a

6

FILE: _i.SECTION: L SHOP e MANUAL

19

Remove spider and shaft assembly from baseand bearing.

20

Remove base bearing snap ring (1).

Press bearing (2) from base.

21

Press base bearing (2) into base.

Install snapring (1).

it ~1/5

2

2

1356

1357

1357

1

1

7

FILE: ..i_.SECTION: £ SHOP MANUAL

Install spiderand base.

22

and shaft assembly bearing

231356

Install drive shaft snap ring.

Use Waldes-Truarc pliers #2 or equal manufactured by Waldes Kohinoor, Inc., LongIsland City, New York.

241355

Install weights, pins, and pinspider and shaft assembly.

NOTE: Install pins from rightwith knurled endat right (2).

clips on

to left

Installed in this manner, centrifugalforce can not throw pins from spider andfree weights.

8

7

SECTION:

Install thrust bearing on thrust sleeve.

26

Install thrust sleeve and bearing on spiderand shaft assembly.

If needed, installof body.

new body bushing in top

1350

B

6 SHOP ~IL~

25

MANUAL ‘a’

1352

27 1351

9

FILE: BSECTION: ..j SHOP MANUAL

A~

28

Install bumper screw in body.

29

Install bearing, snapring, and seal on oneend of rocker shaft,

Install shaft in body and at other end, install bearing, snapring, and seal.

30

Install rocker yoke in body..

Attach to rocker shaft with two capscrews.

C

1349

-s

I

1348

(.10

FILE: ..L_SECTION: ± SHOP MANUAL

Sn

31

Install gasket (1) on base.

Attach body to base with four screws andlockwashers.

32

Install spring lever on rocker shaft.

I

Secure in place with roll pin.

33

1a.

—

I

N

Install throttle lever on rocker shaft.

Secure in place with roll pin.

11

Sr4.-’’;

1342

-j

1

I‘La

* SECTION __ SHOP34

Install speed change bracket

35

itkA XTU ~IYIAIN AL

C-

1341

/

Install speed change spring lever and speedchange shaft

36

Ins tall speed change s≤aftring.

washer and snap-

12

I

1~ I4

38

Ins tall governor on output shaft.

Hook uprods (2)

lubricating line (1) and control

39

If stop screws (1) are in governor, removeand discard.

For correct adjustment, follow procedureoutlined in operator’s manual.

1338

FILE: ~SECTION: ~ SHOP

37

Install governor spring and screw eye andlock nut.

MANUAL

C

3

2

1

13

--

C:

F~.. (