Nano Station User's Guide
-
Upload
jbc-soldering-tools -
Category
Documents
-
view
238 -
download
4
description
Transcript of Nano Station User's Guide
NANANO STATION
www.jbctools.com
NA
www.jbctools.com
2
NA / NANO STATION
NT105-A
NANO SOLDERING
IRON *
NP105-A
NANO TWEEZERS *
0012755 x2
TOOL HOLDER
0011568
CARTRIDGE SET Nº1 *
0009848
ALLEN KEY 1,5mm
CL6230
METALLIC BRUSH
CL6210
BRASS WOOL
N1738
SLEEVES
0011806 x2
CARTRIDGE EXTRACTOR
MANUAL
POWER CORD
* These accessories are not supplied with NA-2B / NA-1B / NA-9B control units
CONTAINS:
C105101 x1
C105103 x1
C105105 x2
C105107 x1
C105112 x1
C105113 x2
NA-2B / NA-1B / NA-9B
CONTROL UNIT
NANO STATION
These accessories are already assembled in the control unit and nano tweezers
Screwsalreadyassembled
3
INSTALLATION
A1205 TOOLS EXTENSIONCORD (1m.)
P-105 PEDAL
Sold separately
PART NAMESACCESSORIES
Power cordsocket
Main switch
Cable collector
Intelligent process control
Equipotential connector
Cartridge extractorand tip aligner
Brass woolMetallicbrush
Heat Management
NA-2B / NA-1B / NA-9B
CONTROL UNIT
NP105-A
NANO TWEEZERS
NT105-A
NANO SOLDERING IRON
1
2
2
1
4
NANO IRON
NANO
TWEEZERS
TOOL HOLDER ASSEMBLY CABLES ASSEMBLY
FAST CARTRIDGE CHANGE
NA / NANO STATION
5
METALLIC BRUSH REPLACEMENT
TIP ALIGNMENT
CARTRIDGE EXTRACTOR REPLACEMENT
Twork
Work WorkHibernation
Tool in the stand2
sec.
Tamb
Temp
Time
ø 0,5
10,7 3,5 0,32,5
0,2 x 0,1 1 x 0,30,4 x 0,2 1,8 x 0,5
6
JBC stations intelligently manage the tool temperature and it helps to extend the tip life:
Work mode: Lift tool from the stand and the tool tip heats up to the selected temperature.
Hibernation mode: When you place the tool in the stand, the power cuts off and the tool cools down to
room temperature.
*The tips of this station have such a small mass that temperature recovery is almost instantaneous. So
the station goes into hibernation mode automatically when the tool is placed in the stand, without going
into sleep mode.
Heat management increase tip life which reduces cost of ownership.
HEAT MANAGEMENT
C105 CARTRIDGE RANGEAll the cartridges shown are actual size. All dimensions are in milimiters (mm).
Contact JBC if other shapes are needed.
C105-101 C105-103 C105-106 C105-105 C105-110C105-107 C105-109
C105-115
Stainless steel tip
C105-111 C105-112C105-108C105-116 C105-113C105-117 C105-114
NA / NANO STATION
7
Main menu
CountersTool sett ings
Exit1 Reset settings2 Station settings3 Tool settings
1 Plugged hours 02 Working hours 03 Sleep hours 0
1 Fix one temp -----2 Temp levels set OFF3 Sleep delay 0 min
4 Counters5 Program version
4 Hibernation hours 0 5 No tool hours 06 Sleep cycles 0
4 Sleep temp 1800C 5 Hibernation delay 30 min6 Temp adjust O OC
Tool NT105Port 1 Port 1/2
Port 1/2Tool NT105Port 1
BackBack
0cSelected temp. 350 oC
P o w e r 1 0 %
350
Decrease & move down Increase & move up
% Instant power supplied to the tool
ORIGINAL PIN: 0105
Stat ion sett ings
1 Temp unit Celsius2 Maximum temp 4000C3 Minimum temp 2000C4 Help text OFF
5 Beep ON6 Change PIN
Back
Access Menu&
Confirm Selection
CONTROL SCREEN
SETTINGS MENU
Tip temperature
WARRANTY
JBC’s 2 years warranty guarantees this equipment against all manufacturing defects, covering the replacement of defective parts and all necessary labour.
Warranty does not cover product wear due to use or mis-use.
In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased enclosing this fully filled in, sheet.
www.jbctools.com
SERIAL Nº
STAMP OF DEALER
DATE OF PURCHASE
0011
844-
0513
TECHNICAL SPECIFICATIONS
- Temperature selection from 90°C (190°F) to 400°C (752°F) (±5%).- Output Peak Power: 12W.- Safety transformer, mains separator and double isolation.- NA-2B 230V 50/60Hz. Input fuse: 0,2A. Output: 7,5V.- NA-1B 120V 50/60Hz. Input fuse: 0,5A. Output: 7,5V.- NA-9B 100V 50/60Hz. Input fuse: 0,5A. Output: 7,5V.- Total weight of unit: 1,8 kg (4,0 lb).- Complies with CE standards on electrical safety, electromagnetic compatibility and ESD protected housing “skin effect”.- RoHS compliant.- Equipotential connector and the tool tip are connected to station mains ground supply for ESD protection.
This product should not bethrown in the garbage.