MUlTiFUNCTIONAl SURFACE TREATMENTS - .STEEL MUlTiFUNCTIONAl SURFACE TREATMENTS ARCOR" treatments

download MUlTiFUNCTIONAl SURFACE TREATMENTS - .STEEL MUlTiFUNCTIONAl SURFACE TREATMENTS ARCOR" treatments

of 4

  • date post

    24-Sep-2018
  • Category

    Documents

  • view

    216
  • download

    0

Embed Size (px)

Transcript of MUlTiFUNCTIONAl SURFACE TREATMENTS - .STEEL MUlTiFUNCTIONAl SURFACE TREATMENTS ARCOR" treatments

  • STEEL

    MUlTiFUNCTIONAl SURFACE TREATMENTS

    ARCOR" treatments have been developed to

    provide multifunctional surface properties. They

    simultaneously enhance the wear, seizure, surface

    fatigue resistance and corrosion resistance (can

    now exceed 800 hours as per neutral salt spray

    testing), These treatments comply with the increa-

    singly severe operating conditions required on steel

    or cast-iron based mechanica I components.

    ARCOR

    CHROME 10IJm

    The ARCOR'" series is based on oxynitrocarburizing

    followed by various post-treatrnents, and offers an

    efficient, economical solution, complying with the

    environment proteetion regulations.

    UNTREATED

    State-of-the-Art solutions via the CLlN"" technology

    (Controlled Liquid lonic Nitriding), developed by

    HEF"" Groupe, ensure a real optimization of the

    treatment parameters.

    COMPARISON OF CORROSION RESISTANCE OF 41/40 STEELWITH ARCOR TREATMENT, WITH HARD CHROME COATING,AND WITHOUT TREATMENT

    (

    )/

  • l=~~J!?-.--_.-jr:treated components exhibit :.r-High mechanical properties : Surface fatigue resistance ;I

    ARCOR TREATED COMPONENTS

    MUL TIP lEP ROP (R TIE S

    Brinelling resistance ;

    Adhesive and abrasive wear resistance ;~~.

    Pitting resistance.

    Good frictional properties :

    Anti-seizure behaviour ;

    Running-in improvement ;

    Surface conformability ;

    Oil film load bearing capacity ;

    Low friction coefficient.

    High corrosion resistance :

    Can reach more than 800 hours tested

    as per ASTM B117.

    iJ Surface roughness functionalities : bearing curve adjustments for lubrication

    optimization ;

    Low Ra, Rt, Rz for no leakage on hydraulic

    components ;

    Deep black highly durable cosmetic aspect.

    AReOR treatments provide :

    No hydrogen embrittlement ;

    Low cycle time processes ,

    High reproducibility and consistency ;

    Evenness of treatment on complex shape com-

    ponents ;

    Adapted for small, medium and large series.

  • CLIN: AN ADVANCED TECHNOLOGY

    The CliN technology is based on the most recent

    developments in the field of liquid oxycarbonitriding

    of HEF R&D, research center of HEF Groupe.

    ... ] ~O lJM.. '..- ~

    Components are processed in an ion ic liquid

    medium. The liquid state during the treatment

    provides homogeneous surface properties whatever

    the shape of the components. It also contributes to

    the absence of part deformation and thermal shock

    effects.CROSS SECTION OF A LAYER OF A

    QUENCHED AND TEMPERED AISI1045 STEEL, ARCOR" TREATED.E IRON NITRIDE LAYER ASPECT

    This CliN technology allows accurate control of

    both nitrogen and oxygen concentrations at the

    surface of the components. This technology results

    in a series of multifunctional treatments where

    frictional properties, surface fatigue resistance and

    corrosion resistance can be adjusted to fit a parti-

    cular application.

    Post treatments like polymer impregnation, high

    quality surface polishing have been developed to

    further increase the corrosion resistance of treated

    components (more than 800 hours as per ASTM

    B117 test), or to adjust the surface roughness for

    low friction against polymerie sealing components.

    This technology can comply with the most stringent

    environment protection regulations with a zero

    liquid and gaseous waste. concept, an solid waste

    recycling.

    1. GAS COLLECTION AND TREATMENT SYSTEM2. WATER RECYCLING SYSTEM

  • ~'M~ 11' lI i :lVitlilout

    tneatrnent ARCOR C ARCOR N ARCOR V~ ~I 11 11

    OF ARCOR TREATMENTS

    CORROSION RESISTANCE

    SUPERFICIAL MECHANICALRESISTANCE

    PROCESS TEMPERATUREi" 630C

    (II.490C

    COMPARISON OF VARIOUS ARCOR~ PROPERT~ES AND FEATURES

    ~.

    f'~;

    The ARCOR" series offers the widest range of

    surface treatments for components that require

    either single or combined frictional properties, anti-

    seizure behaviour, corrosion and surface fatigue

    reststances. The surface properties of all types of

    ferrous materials could be improved with the

    ARCOR" treatments (steel, cast iron, sintered

    ferrous alloys...).

    Via the ClIWM technology the ARCOR" treatments

    allow one to adjust the nitrogen and oxygen concen-

    tration at the surface of the parts. In combination

    with the, adjustme~f of process parameters' like time

    and temperature (frorn 490C to 630C), and 'pre

    or post heat treatments, specific properties can

    be achieved (corrosion resistance, anti-seizure

    behaviour, brinelling resistance). The ARCOR"

    series can also be combined with heat treatments

    like carburizing, induction hardenlng. Components

    processed with these combined treatments exhibit

    high volumic and sub-surface mechanical properties

    together with friction and corrosion resistance

    properties.

    Today recognised as a standard surface treatment in

    automotive industry with its C vers ion, the ARCOR

    series is completed with the new N and V types,

    providing respectively extreme corrosion resistance

    and outstanding superficial mechanical properties.