Multi-taskingOKUMA Multus B300W

Multi-taskingMori-Seiki NT

Multi-taskingMazak Integrex Mark IV

Multi-taskingMachine Definition

Multi-taskingAxis combinations

Multi-taskingAxis combinations

Multi-taskingStock Setup

Multi-taskingTool Setup – Define lathe tools in B=0 position.

Multi-taskingTool Setup – Define lathe tools in B=0 position.

Mazak IntegrexOkuma Multus

Mori Seiki NT

Multi-taskingTool Angle – One tool can be defined to work in any possible configuration using

Tool Angle

Tool Angle = BA: Angle (Okuma

Multus)

Tool Orientation on Machine: Indexes a tool to work on Left spindle or Right spindle and for back turning on either

spindle (M602 or M603- Okuma Multus)

Multi-taskingTool Orientation on Machine: Indexes a tool to define Position B

(Okuma Multus - M602 or M603)

N220G97 G95 S=3800 M42 M602 BA=90. TL=011011

Multi-taskingTool Orientation on Machine: Indexes a tool to define Position B

(Mori-Seiki NT D1 or D2)

Defining Lathe tool output

Tool ID Code: MR2

For consistency, the general guidelines below are suggested

Multi-taskingTool Orientation on Machine: Indexes a tool to define Position B

(Integrex Mark IV - Matrix)

(PROGRAM NAME - MULTI-TASKING DEMO_MJR1 DATE=DD-MM-YY - 22-02-09 TIME=HH:MM - 13:47 )

(POST LICENSE - IN-HOUSE SOLUTIONS INC.)(T11 | CNMG 08 OD R | DIA. - 11 | SUFFIX - .02 | INSERT - CNMG 12 04 08)G21 G69 G80 G40 G18 G90 G94M205(UPPER TURRET)G109 L1(T11 | CNMG 08 OD R | DIA. - 11 | SUFFIX - .02 | INSERT - CNMG 12 04 08)(TOOLPATH GROUP - PREP STOCK )G21 G10.9 X1N1 G91 G28 X0.N1 G28 Y0. Z0.M901M202T11.02 T11 M06G91 G28 X0. Z0.G90M108G0 G90 G53 B90.M107G54. . .

Multi-tasking

N220G97 G95 S=3800 M42 M602 BA=90. TL=111111N230 M4

Multi-taskingProgram: Facing / Drilling / ID Boring

Multi-taskingMisc Ops: Stock Flip

Multi-taskingMisc Ops: Stock Flip

Multi-taskingFace / Drill / ID Bore (rough) / ID Bore undercut finish

Multi-taskingID Bore undercut

N220G97 G95 S=2816 M42 M602 BA=-10. TL=330933N230 M4

Multi-taskingOD Rough / Finish / Plunge Cut Parameters

Multi-taskingOD Finish Back turning

N220G97 G95 S=509 M41 M603 BA=90. TL=004004N230 M3

Multi-taskingFinish ID / Thread OD

Multi-taskingMill slot / Transform toolpath

T/Cplane TOP in Mill is C=90. BACK is C=0

. . .N210G94 SB=2000 M241 M63 M9 BA=90. G52 TL=303030N220 M13N230 G138N240 G17N250 M146N260 G0 C90.N270 M147N280 G127 B90.N290 G0 Z155.N300 X37.5 Y0.N310 Z65.. . .

Multi-taskingCircle Mill counterbore / Drill / Tap angled holes

Multi-taskingMisc Ops: Stock Flip back to OP1 position

Geometry exists already. Transfer geometry not required

Multi-taskingStock Flip – Original position

Multi-taskingFace – Stock recognition

Multi-taskingRough / Semi-finish ID

Multi-taskingRough OD / Finish OD

Multi-taskingThread

Multi-taskingFinish corners