Muestrario de refacciones Heidelberg®equiposgraficos.com/images/Catalogo_refacciones... · 2021....

EFFECTUS GRAPHICUS ORTUS S.A. DE C.V. www.equiposgraficos.com

Salónica 259 Col. Sector Naval. México D.F. 02080 Tel: +52 (55) 5396 6580

Muestrario de refacciones Heidelberg®

IMPORTANTE:

Este es el Muestrario de Refacciones Comunes para Heidelberg® Si usted desea ver un listado completo con todas las refacciones, consulte el

Catálogo de Refacciones para Heidelberg®. Intrucciones

1. Identifique la figura (Drawing #) de la sección de su interés. 2. Identifique el número en la figura (Key #) de la parte que busca . 3. Utilice el número en la figura para identificar el número de parte (Part #) en la/s

página/s siguientes. 4. Ingrese a www.equiposgraficos.com y complete el formulario de cotización

incluyendo el número de parte y descripción. 5. Solicite asistencia a [email protected] o al +52(55) 5396 6580

Gracias por su compra

http://www.egomexico.com/images/Productos/PRP/Catalogo_refacciones_Heidelberg.pdf

http://www.egomexico.com/images/Productos/PRP/Catalogo_refacciones_Heidelberg.pdf

http://www.equiposgraficos.com/

http://128.121.161.225/cotizacion.htm

mailto:[email protected]

PART # PART #

21 Solo una muestra de nuestro catalogo www.equiposgraficos.com

Replacement parts for: HEIDELBERG

PUMP FILTER - Quickmaster 46

P-9470 31.20

SILENCER P-9413 65.00

RIBBED V-BELTS

TOK - Drive motor (610mm) P-3780 16.50TOK - Drive shaft (762mm) P-3783 36.50GTO 46 - Drive motor (1168mm) P-3785 57.00GTO 46 - 4 Color Drive Belt P-3733 69.00GTO 46/52 - Drive motor P-3716 41.00GTO 52 - Drive motor (1321mm) P-3788 98.80GTO 52 Z/P, V/P - Drive motor (1016mm) P-3790 89.90GTO 52 Z/P, V/P - Drive motor (1397mm) P-3791 69.50Windmill 10 X 15 - Main drive (2150 mm) P-3703 352.00Windmill 10 X 15 - Main drive P-3793 199.80Windmill 10 X 15 - Main drive (2362 mm) P-3893 154.90 Windmill 13 X 18 - Main drive P-3722 229.90

TIMING BELTS - TOKSTACK-LOAD MASTER FEED P-3810 19.00MASTER FEED TABLE P-1697 7.50

FEED TAPESPEEDMASTER 72 & 102 P-3918 34.60MO, SORK P-3927 19.00

SHEET SEPARATORS

(A) KORD (45°) HE-KØ114 7.00(B) KORD (45° with pad) HE-KØ420 10.90(C) KORD (90°) HE-KØ117 7.00(D) K-Series HE-KS117 11.90(E) K-Series w/hood HE-KS114 9.90(F) GTO 46 HE-46117 5.60(G) GTO 46 (with hood) HE-46114 6.00(H) GTO 52 HE-52117 9.90(I) GTO 52 (with hood) HE-52118 9.90(J) GTO 52 (45°) HE-52114 3.20(K) M/S Series HE-SØ117 24.90(L) M/S Series HE-SØ114 29.90(M) M/S Series HE-SØ106 33.90(N) SB Series (90°) HE-SB117 9.50(O) SB Series (45°) HE-SB114 9.50(P) WINDMILL HE-WI114 10.00(Q) WINDMILL HE-WI117 9.50(R) Quickmaster 46/46DI HE-46114QM 24.90(S) GTO (Operator side) HE-52106 53.40(T) SM52/74 (Operator side) HE-52106SM 64.90(U) GTO (Non-Operator side) HE-52107 53.40(V) SM52/74 (Non-Operator side) HE-52107SM 64.90(W) M/S/SM102 Brush HE-S0107 29.90

RUBBER HOOD For sheet separators.

HE-46114-R 4.90

SHEET SEPARATOR BARQUICKMASTER 46 & 46DI

HE-46117QM 224.90

PLATE SPRING For Quickmaster

4mm HE-46099QM-4mm 6.406mm HE-46099QM-6mm 11.00

SHEET STEADIER BRUSH - GTO 46 / 52, K-SeriesComplete HE-46403 82.00

Brush only HE-46420 6.00Wing nut P-3399 2.00Shoulder screw P-8176 9.90

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

SHEET SEPARATOR HOLDER

KOR HE-KØR113 34.00

SHEET SEPARATOR HOLDER - L.H. & R.H.••• UNIVERSAL. WORKS ON BOTH SIDES OF FEEDER.

KORA, KORD, KORS HE-KØRD113 28.90

BRUSH WHEELS For feeder section.

K, M, S, SPEEDMASTER (whtie bristle) HE-SR420 21.20K, M, S, SPEEDMASTERfor cardboard stock (black bristle) HE-SR500 24.00

FEED GRIPPER COMPLETE - GTO 46 & 52

COMPLETE HE-46511 899.90(A) Gripper finger HE-46212 12.00(B) Hex head screw P-2088 .60(C) Needle bearing P-3466 19.90(D) Cam roller P-6838 38.90(E) Flat washer P-595 .60(F) E-ring P-2759 .60(G) Stud-for cam roller P-7943 23.00(H) Taper pin P-431 .60(I) Connecting piece P-11923 9.90(J) Torsion spring HE-46212-T 3.00(K) Gripper pad not sold alone -------(L) Spring HE-46212-E 24.90(M) Grooved pin P-3037 .60(N) Torsion Spring (not shown) (see note) -------(O) Backing Plate HE-46212-BP .90

NOTE: Torsion spring “N” is obsolete. Spring “L” & grooved pin “M” are used in place of it.

SPRING For traveling feed gripper.

K-series HE-K0144 6.50

SUCKER FEET

(A) GTO (9/32 ID x 3/4 OD gum rubber - blue) P-5222 .90(A) GTO (9/32 ID x 3/4 OD polyurethane - red) P-7568 1.80(B) GTO (5/16 ID x 11/16 OD for cardboard) P-5244 1.75(C) HEIDELBERG/KLUGE (7/8” O.D.) P-5210 1.60(C) HEIDELBERG (1-1/16” O.D.) P-7556 1.20(D) HEIDELBERG (5/32” I.D. x 1” O.D.) P-5223 .80(D) WINDMILL (5/32” I.D. x 7/8” O.D.) P-7566 .60(D) WINDMILL (1/8” .ID. x 29/32 O.D.) P-5234 .70(E) SOR (1-1/4” O.D.) P-5236 .80(E) MO/SOR (1-3/16” O.D.) P-5240 .80(E) MO/SOR (1-1/2” O.D.) P-5243 1.00(E) Speedmaster 52 (6/16 I.D. x 1-3/16 O.D.) P-7564 .80(F) SORKZ For tissue paper P-5218 7.00(G) TOM/TOK (1-1/4 Long) P-5215 1.20(G) Quickmaster (11/16 Long) P-7558 .80

SPRING GUIDE (TONGUE) For conveyorK- series HE-KØR420 8.50

RETAINER SPRING For GTO 52 feeder.HE-SØ711 2.40

GRIPPER FINGERHE-46212

B

K I J

GD

FEC

L

MO

A B C D E F G

Solo una muestra de nuestro catalogo www.equiposgraficos.com

PART # PART #

22


HOLDER ASSEMBLY - GTO 46/52, WINDMILL PLATENSComplete HE-WI434 59.80Replacement roll pin P-2839 .60Replacement thumb screw P-2022 3.90

SHEET STEADIER ASSEMBLY - GTO 46 / 52, K-SeriesComplete HE-KØØ27 81.90(A) Sheet steadier HE-KØR090 38.90(B) Holder HE-46049 35.90(C) Thumb screw P-2022 3.90

FRONT GUIDE - For GTO 46/52, K-Series

(A) Guide only HE-KØ383 39.90(B) Adjusting knob P-2932 24.10(C) Retainer spring HE-KØ257 5.50(D) Adjusting screw P-2912 19.90

SHEET STEADIER BRUSH - S-SERIESComplete HE-SR467 159.90(A) Hex head screw P-2077 .60(B) Flat washer P-581 .60(C) Nut P-2603 .60(D) Thumb screw P-2924 24.90(E) Bracket only HE-SR485 54.90(F) Spring washer P-654 .80(G) Sheet steadier brush HE-SR475 69.90

FEEDER BRUSH WHEEL - S-Series, Spdmst. 72/102Complete HE-SR403 89.90(A) Spring P-12319 1.40(B) Thumb screw P-2903 8.90(C) Small bracket HE-SR498 22.00(D) Hex head screw P-2043 .60(E) Large bracket HE-SR473 38.90(F)Thumb screw P-2924 24.90(G) Holder HE-SR492 44.90(H) Pin P-4777 7.00(I) Brush wheel HE-SR420 21.20(J) E-Ring P-2753 .60

SHEET SMOOTHERS

KOR (Complete) HE-KØR434 134.90KORD/KORA (Complete) HE-KØRD434 118.90KORS (Complete) HE-KØRS434 123.90(A) Spring plate (smoother) HE-KØ779 3.00(B) Screw P-2355 .80(C) Bar only (KOR) ** HE-KØR483 61.90(C) Bar only (KORD/KORA) ** HE-KØRD483 61.90(C) Bar only (KORS) ** HE-KØRS483 79.80(D) Block HE-KØR359 33.80(E) Thumb screw P-2924 24.90

SHEET SMOOTHER - GTO 46 (Long)

Complete HE-46434 109.80(A) Bar only HE-46483 59.90(B) Thumb screw P-2924 24.90(C) Block only HE-KØR359 33.80(D) Screw P-2305 .60(E) Nut P-2600 .60(F) Pan head screw P-2355 .80(G) Plate spring HE-46779 2.50(H) Roll pin P-516 .60

A CB

A

BC

D

AB

CE

DFG

J I H

GF

ED

BA

D

E

CB

A

C

B F

G

D&E

HA

SHEET SMOOTHER - GTO 46 (Short)Complete HE-46352 89.80(A)Bar only (Not Sold Alone) --------(B)Thumb screw P-2924 24.90(C)Block only HE-KØR359 33.80(D)Roll pin P-516 .60

Note: ** bars come without holes - you must drill holes to match your existing block.

SHEET SMOOTHER - GTO 52Complete HE-52434 119.90(A) Bar only HE-52483 59.90(B) Thumb screw P-2924 24.90(C) Block only HE-KØR359 33.80(D) Pan head screw P-2355 .80(E) Plate spring HE-46779 2.50(F) Roll pin P-516 .60

Note: ** bars come without holes - you must drill holes to match your existing block.

SHEET SMOOTHER PLATE SPRINGS

SORZ, SORDZ, SORSZ HE-SØ588 19.90

SORKZ, SORMZ HE-SØ924 10.90

SHEET SMOOTHER - S-SeriesComplete (Operators side) HE-SØ562 160.00Complete (Drive side) HE-SØ568 160.00(A) Spring plate HE-SØ779 3.20(B) Screw P-10207 .60(C) Bar only ** HE-SØ483 64.90(D) Block HE-SØ359 38.90(E) Thumb screw P-2923 9.90(F) Spacer piece (oper. side) HE-SØ541 42.90(F) Spacer piece (drive side) HE-SØ573 42.90

SHEET BRAKE - GTO 46 / 52, K-SeriesComplete HE-52467 70.00(A) Strap only HE-52500 9.90(B) Block only HE-52473 29.90(C) Thumb screw P-2924 24.90(D) Stop nut P-2610 .60(E) Screw P-8174 10.40

D

ACB

C

B D

F

AE

E

D C

F

AB

AE

B

DC

PART # PART #



TRANSFER GRIPPER - MOZ, SPEEDMASTER, SORKHE-MT225 38.90

GTO 46 / 52(A) Transfer and Imp. drum (urethane tip) HE-52245 49.90(A) Transfer and Imp. drum (plain metal tip) HE-52237 33.00(B) Imp.—Perfecting drum (urethane tip) HE-MØ237 135.90

Reversing Drum (upper position) HE-521020-RU 79.90Reversing Drum (lower position) HE-521020-RL 59.90

K-SERIES(C) Transfer and Imp. drum (metalized grit tip)HE-KØR225 39.50

M-SERIES(D) Feed drum (urethane tip) HE-72225 38.90(A) Transfer and Imp. drum (urethane tip) HE-52245 49.90(A) Transfer and Imp. drum (plain metal tip) HE-52237 33.00(A) Transfer drum—Coating unit (metal tip) HE-52237 33.00(A) Imp. drum—Coating unit (urethane tip) HE-52245 49.90(A) Imp. drum—Coating unit (plain metal tip) HE-52237 33.00

HE-MO1020 19.90HE-MO1050 6.90

QUICKMASTER 46 / 46DI & TOM / TOK(E) Impression drum (urethane tip) HE-46237QM 30.50

S-SERIES(F) Transfer and Imp. drum (urethane tip) HE-SK237 65.00(F) Transfer and imp. drum (plain metal tip) HE-SK245 39.00(J) Imp. cylinder gripper-SBD (urethane tip) HE-SBD237 189.90

HE-SK1000 87.90

SPEEDMASTER 72 (F) Transfer and Imp. drum (urethane tip) HE-SK237 65.00(F) Transfer and Imp. drum (plain metal tip) HE-SK245 39.00(G) Imp.—Perfecting drum (plain metal tip) HE-72245S 110.90(G) Transfer drum (large)

—Perfecting (plain metal tip) HE-72245S 110.90

SPEEDMASTER 102(H) Feed drum (urethane tip) HE-102237 29.20(H) Feed drum (plain metal tip) HE-102245 36.90(H) Transfer and Imp. drum (urethane tip) HE-102237 29.20(H) Transfer and Imp. drum (plain metal tip) HE-102245 36.90( I ) Imp.—Perfecting drum (plain meta l tip) HE-102225 53.90

GROOVED GRIPPER PADS - Speedmaster 72

Cross groove HE-72422-CG 59.90Parallel groove HE-72422-PG 46.90

GROOVED GRIPPER PADS - Speedmaster 102

Cross groove HE-102422-CG 24.90Parallel groove HE-102422-PG 59.90Diamond groove HE-102422-DG 22.00

Forwarding Sucker Assembly

Operator Side HE-S0990-0S 769.90

Non-Operator Side HE-S0990-DS 769.90

GROOVED GRIPPER PADS (Cross groove)Speedmaster 72 / 102 (after perfector)Drive side HE-72442-D 336.00Center HE-72442-C 155.00Operators side HE-72442-Ø 420.00

A B C D E

F G H I J

INK DISTRIBUTOR ADJUSTING BLOCKS - K-SeriesDrive side (complete) HE-KØR494K-DS 264.00(consists of (A) thru (J) & (K) HE-KØR494-DS. 120.00Operators side (complete) HE-KØR494K-ØS 264.00(consists of (A) thru (J) & (K) HE-KØR494-ØS. 120.00BEARING LATCH ASSEMBLY (items (A) thru (F).(A) Screw-Cone point P-2132 3.90(B) Spring HE-46896 .80(C) Latch HE-KØR494-L 28.50(D) Stud P-7164 9.80(E) Spring washer P-11826 2.90(F) Taper pin P-431 .60

JOURNAL BOX ASSEMBLY (items (G) thru (J).(G) Journal box HE-KØR494-JB 38.00(H) Retaining ring P-2771 .60(I) Needle bearing P-2117 15.90(J) Adjusting screw P-2913 8.20(K) Block (drive side) HE-KØR494-DS 120.00(K) Block (oper. side) HE-KØR494-ØS 120.00

JOURNAL BOX HOUSING ASSY. (items B, G, H, I, &J)HE-KØR494-JBC 104.00

SPINDLE For blanket cylinder

TOM, TOK P-27744 44.90

SHEET STOP For side laysM-Series, S-series, Speedmaster

HE-102100 38.90

CLAW For blanket clamp HE-46390 8.90

THREADED BUSHING For plate cylinderGTO 46 & 52 HE-46329 30.00

TRIP BLOCK For plate camGTO 52 HE-52391 3.20

ADJUSTING SCREW - For WINDMILL LAY BAR

10 X 15, 13 X 18(32 mm O.A.L.) HE-WI135-32 77.90(39 mm O.A.L.) HE-WI135-39 67.90

CYLINDER BRUSHES

KOR, KORA, KORD-62 P-7659 401.00KORD-64 P-7657 499.90KORS P-7658 349.90

BLANKET BAR ASSEMBLY - M-Series

Complete HE-MØ252 479.90(A) Upper clamp HE-MØ258 312.00(B) Lower clamp HE-MØ256 312.00(C) Screw (7 per assembly) P-2009 .60(D) Spring (6 per assembly) (not shown) P-12319 1.40

HOLDER ASSEMBLY - GTO 46 / 52, K-Series

Complete HE-KØ625 49.90Replacement roll pin P-2839 .60Replacement thumb screw P-2022 3.90

A

B

C


PART # PART #

24


BLANKET BAR ASSEMBLIES

Complete (GTO 46) HE-46252 380.00Complete (GTO 52) HE-52252 323.80Complete (SM 52) HE-52252SM 579.90Complete (KOR) HE-KØR252 799.90Complete (KORD) HE-KØRD252 810.00Complete (KORS) HE-KØRS252 899.90Complete (SM 72) HE-72252 400.00Complete (SM 74) HE-74252 639.90Complete (SM 102) HE-102252 465.00Complete (SORDZ) HE-SØRDZ252 909.80Complete (SORKZ) HE-SØRKZ252 650.00Complete (SORZ) HE-SØRZ252 670.00

PLATE CLAMP ASSEMBLY - TAIL EDGE

GTO 46 Complete HE-46367 591.90GTO 52 Complete HE-52367 639.80

(A) Upper clamp - GTO 46 HE-46359 124.90(A) Upper clamp - GTO 52 (left hand) HE-52359-L 69.90(A) Upper clamp - GTO 52 (right hand) HE-52359-R 69.90(B) Knurled adjusting nut P-2949 26.90(C) Eccentric shaft - GTO 46 HE-46435 58.90(C) Eccentric shaft - GTO 52 HE-52435 64.50(D) Adjusting stud P-7198 21.90(E) Lower clamp - GTO 46 HE-46353 240.00(E) Lower clamp - GTO 52 HE-52353 240.00(F) Threaded stud P-9138 13.00(G) Spring P-12909 2.50(H) Screw P-2418 .90(I) Metal strip - GTO 46 HE-46353-M 40.00(I) Metal strip - GTO 52 HE-52353-M 45.00(J) Set screw (not shown) P-2508 .60(K) Rubber strip - GTO 46 HE-46353-R 15.80(K) Rubber strip - GTO 52 HE-52353-R 15.80

(I,K) Metal & rubber strip assy. - GTO 46 HE-46353-MSR 79.60(I,K) Metal & rubber strip assy. - GTO 52 HE-52353-MSR 79.60

PLATE CLAMP ASSEMBLY - LEAD EDGE

GTO 46 Complete HE-46788 499.90(A) Upper clamp HE-46359 124.90(B) Eccentric shaft HE-46435 58.90(C) Thumb screw P-2917 13.90(D) Spring HE-46896 .80(E) Screw P-2101 .60(F) Washer P-5519 .60(G) Adjusting bracket HE-46755 32.90(H) Lower clamp HE-46353 240.00(I) Spring P-12909 2.50(J) Screw P-2418 .90(K) Metal strip HE-46353-M 40.00(L) Set screw (not shown) P-2508 .60(M) Rubber strip - GTO 46 (not shown) HE-46353-R 15.80(K,M) Metal & rubber strip assy. - GTO 46 HE-46353-MSR 79.60

PLATE CLAMP ASSEMBLY - TAIL EDGE - For BACHER PLATEGTO 46 Complete HE-46367-BC 639.80(A) Upper clamp - (L.H.) HE-46359-L 69.90(B) Upper clamp - (R.H.) HE-46359-R 69.90(C) Knurled adjusting nut P-2949 26.90(D) Flat washer P-10942 1.20(E) Eccentric shaft HE-46435 58.90(F) Adjusting stud P-7198 21.90(G) Lower clamp sub assembly HE-46353-BC-S 240.00(H) Lower clamp only HE-46353-BC 180.00(I) Rubber strip HE-46353-R 15.80(J) Metal strip HE-46353-M 40.00(K) Threaded stud P-9138 13.00(L) Spring P-12909 2.50(M) Screw P-2418 .90(I,J) Metal & rubber strip assembly HE-46353-MSR 79.60

PLATE CLAMP ASSEMBLY - LEAD EDGE - For BACHER PLATEGTO 46 Complete HE-46788-BC 839.80(A) Collar P-6725 55.80(B) Collar scale P-6726 63.00(C) Adjustment holder HE-52351 29.80(D) Washer P-2749 1.00(E) Spacer P-6802 7.90(F) Spring P-12148 3.80(G) Threaded stud P-9137 14.90(H) Spring P-12909 2.50(I) Adjusting block HE-52755 29.90(J) Ring scale P-6724 55.80(K) Adjusting stud P-7199 7.90(L) Lower clamp HE-46353-BC 180.00(M) Metal strip (not shown) HE-46353-M 40.00(N) Eccentric shaft (2 per assm) HE-46435 58.90(O) Upper clamp (1 per assm) HE-46359 124.90(P) Rubber strip (not shown) HE-46353-R 15.80(M,P) Metal & rubber strip assembly HE-46353-MSR 79.60

PLATE CLAMP ASSEMBLY - LEAD EDGEGTO 52 Complete HE-52788 699.90(A) Clamp HE-52359 134.90(B) Knurled adjusting nut P-2949 26.90(C) Spacer P-6843 5.80(D) Spring P-12148 3.80(E) Eccentric shaft HE-52435 64.50(F) Spring P-12909 2.50(G) Adjusting stud P-7198 21.90(H) Lower clamp HE-52353 240.00(I) Screw P-2418 .90(J) Set screw P-2508 .60(K) Metal strip HE-52353-M 45.00(L) Rubber strip (not shown) HE-52353-R 15.80(K,L) Metal & rubber strip assembly HE-52353-MSR 79.60

PART # PART #



PLATE CLAMP ASSEMBLY - LEAD EDGE - For BACHER PLATE

GTO 52 Complete HE-52788-BC 639.90(A) Collar P-6725 55.80(B) Collar scale P-6726 63.00(C) Adjustment holder HE-52351 29.80(D) Spacer cam P-6843 5.80(E) Spring P-12148 3.80(F) Threaded stud P-9137 14.90(G) Adjusting stud P-7199 7.90(H) Adjusting block HE-52755 29.90(I) Lower clamp HE-52353 240.00(J) Metal strip HE-52353-M 45.00(K) Spring P-12909 2.50(L) Hex head screw P-2089 20.40(M) Ring scale P-6724 55.80(N) Nut P-2634 6.50(O) Eccentric shaft HE-52435 64.50(P) Clamp HE-52359 134.90(Q) Rubber strip HE-52353-R 15.80(J,Q) Metal & rubber strip assembly HE-52353-MSR 79.60

PLATE CLAMP ASSEMBLY - KORD 64

Complete HE-KØRD367 1,049.80(A) Screw (4 per assm) P-2008 .60(B) Upper clamp HE-KØRD359 300.00(C) Flat washer P-10942 1.20(D) Spring (4 per assm) P-12319 1.40(E) Lower clamp HE-KØRD353 569.90(F) Screw (2 per assm) P-2105 .70(G) Washer (2 per assm) (not shown) P-5519 .60(H) Block HE-KØR755 128.90(I) Nut (3 per assm) P-2604 .60(J) Set screw (3 per assm) P-2510 1.20

INK UNIT OVER-RUNNING CLUTCH ASSEMBLYCOMPLETE (K-Series) HE-KØ370 829.90COMPLETE (SM 72/102) HE-72370-CON

(A) Retaining ring P-2778 1.30(B) Flat washer P-2715 4.90(C) Ring washer P-2716 4.90(D) Bearing cage P-3452 43.00(E) One-way clutch bearing P-3447 279.90(F) Bearing cage P-3448 149.90(G) Housing Not Sold Alone - - - - -(H) Sleeve HE-KØ370-S 159.90

ADJUSTING GEAR For distributor roller.

KORD 64 HE-KØRD516 179.90

B D C I H F J A

E

GB

A

C

D E

F

H

• STANDARD CYLINDER JACKETSWINDMILL 10 X 15 .....10 x 14-1/4 ......................... P-30850 75.00WINDMILL 13 X 18....... 12-7/8 x 17-3/4 ................... P-30858 102.50GTO 46 ........................ 15-1/2 x 18 ......................... P-30851 50.00GTO 52 ........................ 16 x 20-3/8 ......................... P-30852 74.00M-Series....................... 21-1/2 x 26 ......................... P-30853 149.90KORD 62 ..................... 19-1/4 x 24-7/16 ................. P-30854 119.80KORD 64 ..................... 19-1/2 x 25-1/2 ................... P-30855 129.00KOR ............................. 16-3/4 x 22-1/2 ................... P-30859 199.90KORA .......................... 17 x 22-1/2 ......................... P-30857 110.90KORS .......................... 22-1/2 x 28-1/2 ................... P-30856 151.80Speedmaster 52 ........... 15-1/4 x 20-7/8 ................... P-30867 249.90

• REFINED CYLINDER JACKETSGTO 46 ........................ 15-1/2 x 18 ......................... P-30860 599.90GTO 52 ........................ 16 x 20-3/8 ......................... P-30861 998.00MO ............................... 21-3/4 x 26.......................... P-30862 1,699.00Speedmaster 72 .......... 21-1/16 x 29-1/4 ................. P-30863 1,455.00Speedmaster 74 ........... ........................................... P-30872 1,867.00Speedmaster 102 ........ 27-15/16 x 40-3/4................ P-30864 1,998.00

• DIE CUTTINGKSBAZ ........................ 21-1/2 x 28-1/2 ................... P-30865 290.00SBB, SBBS, SBBZ ....... 21-1/4 x 32-1/4 ................... P-30866 299.90KSBA .......................... 18-5/8 x 22-1/2 ................... P-30869 193.05S-Series ...................... 22-1/4 x 28-3/8 ................... P-30887 184.00SBG ............................. 24 x 30-1/4 ......................... P-30890 320.00

INK DISTRIBUTOR RUNNERWINDMILL 10x15 HE-WI466 17.70

DOG AND WORM - Quickmaster 46 / 46DI

Dog & Worm set HE-46464QM-K 153.90

Worm - Ink / Water HE-46464QM 128.90Dog - Water HE-46428QM 74.90

INK FOUNTAIN END PLATESSold as a set of 1 Left hand & 1 Right hand.Quickmaster 46 HE-46566QM 79.90Quickmaster 46DI HE-46566QMDI 110.00GTO 52 HE-52566 159.00GTO 52 CPC/CPT HE-52566CP 218.00GTO 46/52 Numbering Unit HE-46566-N 99.90Speedmaster 52 HE-52566SM 133.40Speedmaster 72 HE-72566 165.60Speedmaster 74 HE-74566 107.00Speedmaster 102 HE-102566 165.60MO HE-MØ566 120.00Spring plate for all (O.S.) HE-72261 7.00Spring plate for all (N.O.S.) HE-72082 7.00Hickey picker for all P-31108 .60


PART # PART #

26


HICKEY REMOVERS

(A) SORS, SORD, SORM, MOP-29981 79.90

(B) Speedmaster 52 P-29983 79.90

(C) Speedmaster 74 P-29982 79.90

(D) Speedmaster 102 P-29980 79.90

RUBBER REPLACEMENT (not shown)for P-29980 only. P-31336 4.00

ADJUSTING SCREW ASSEMBLYComplete HE-46427 66.00(A) Screw P-6530 44.90(B) Brass stud P-7174 31.50(C) Nut P-2601 .60(D) Lockwasher P-11830 .60

INK BLADE ADJUSTING SCREWS

(A) K-Series P-2929 22.90(B) GTO 46/52, M/S Series, Spdmstr 72

P-2928 26.90(C) TOK P-2021 5.20

INK ROLLER ASSEMBLY - Windmill 10x x15 (With bearings and runners.)Complete P-31999 148.90

WATER BACK UP / FEED COLLAR ASSY - K-Series

COMPLETE HE-KØ538 243.80(A) Collar - w / “B & D” HE-KØ355 237.80(B) Bearing P-3460 6.00(C) Spring P-362130 1.80(D) Roll pin P-10452 .60(E) Cam roller P-6838 38.90(F) Stud P-7169 21.00

BEARING SUPPORTS

GTO 46 D.S. - RED / O.S. - YELLOW, GTO 52 D.S. - RED -COMPLETE (w/o latch) HE-46558 340.00GTO 52 O.S. - YELLOW -COMPLETE (with latch) HE-52558 470.00GTO 46 & 52 D.S. - YELLOW / O.S. - RED -COMPLETE (w/o latch) HE-46614 339.90(A) Set screw Not Sold Alone ---------(B) Set screw P-2538 1.40(C) Shoulder screw P-8171 9.90(D) Handle P-7214 24.90(E) Spring (inside handle “D”) Not Sold Alone ---------(F) Trunnion stud P-7173 25.90(G) Set screw (to hold “H”) P-2501 .60(H) Eccentric stud P-7163 47.90(I) Dowel pin with o-ring P-4780 10.50(J) O-ring (comes with P-4780) P-5330 .60(K) Spring (underneath “B”) P-152422 3.90

A

B

CLOWER DAMPENING BEARING SUPPORT

GTO 46 & 52 D.S. GREEN - Complete HE-46415 574.00GTO 46 & 52 O.S. GREEN - Complete HE-46400 574.00(A) Spring (inside handle “B”) HE-46896 .80(B) Handle P-7214 24.90(C) Shoulder screw P-8171 9.90(D) Dowel pin P-3132 6.90(E) Trunnion stud P-7173 25.90(F) Set screw (to hold “G”) P-2501 .60(G) Eccentric stud P-7163 47.90(H) Grooved pin P-2899 4.50(I) Grooved pin with o-ring P-4780 10.50(J) O-ring (comes with P-4780) P-5330 .60(K) Brass stud P-7174 31.50(L) Nut P-2601 .60(M) Screw (for brass stud) P-6530 44.90

UPPER DAMPENING BEARING SUPPORT

GTO 46 & 52 D.S.Complete HE-46344 349.90GTO 46 & 52 O.S.Complete HE-46346 339.90(A) Support only HE-46350 149.90(B) Handle P-7214 24.90(C) Shoulder screw P-8171 9.90(D) Spring (inside handle “B”) HE-46896 .80(E) Trunnion stud P-7173 25.90(F) Set screw (to hold “G”) P-2501 .60(G) Eccentric stud P-7163 47.90(H) Dowel pin with o-ring P-4780 10.50(I) O-ring (comes with P-4780) P-5330 .60

INK FOUNTAIN BLADES

WINDMILL 10x15 .............. (37.6 cm x 10.1 cm) ....HE-WI095-15 299.90WINDMILL 13x18 .............. (48.0 cm x 10.1 cm) ....HE-WI095-18 447.90GTO 46 ............................. (45.3 cm x 8.4 cm) ......HE-46095 450.00GTO 46 (Numbering Unit) ... ...................................HE-46095-N 899.90GTO 52 ............................. (51.3 cm x 9.4 cm) ......HE-52095 399.90GTO 52 (Segmented) ......... ...................................HE-52095-S 1290.00GTO 52 (Numbering Unit) ... ...................................HE-52095-N 899.90KOR .................................. (58 cm x 10.1 cm) .......HE-KØR095 369.90KORD 64 .......................... (67.1 cm x 10.1 cm) ....HE-KØRD095 350.00KORS ................................ (74.2 cm x 10.1 cm) ....HE-KØRS095 328.50M Series ............................ (66.2 cm x 12.9 cm) ....HE-MØØ95 479.90SORDZ .............................. (90.1 cm x 11.7 cm) ....HE-SØRDZ095 600.00SORM ............................... (73.0 cm x 11.7 cm) ....HE-SØRM095 979.90SORMZ ............................. (73.1 cm x 17.5 cm) ....HE-SØRMZ095 750.00SORZ ................................ (83.1 cm x 11.8 cm) ....HE-SØRZ095 599.90SORKZ ............................. (66.0 cm x 11.8 cm) ....HE-SØRKZ095 593.00SORSZ ............................. (103.1 cm x 17.5 cm) ..HE-SØRSZ095 974.90TOK, TOM (27.6 cm x 7.1 cm) ......HE-T0095 280.00QUICKMASTER 46 ........... (33.6 cm x 7.1 cm) ......HE-46079QM 240.00

PART # PART #


Replacement parts for: HEIDELBERG.................................Continued thru page 31.

DAMPENING ROLLER ADJUSTMENT BLOCK

Complete HE-KØR416 140.00(A) Gear shaft HE-KØR304 73.90(B) Spring HE-KØR328 2.00(C) Bracket HE-KØR418 89.80(D) Knurled nut P-2946 9.50(E) E-ring P-2754 .60(F) Decal washer P-7464 4.90(G) Decal washer P-7465 4.90(H) Nut P-2603 .60

WATER TROUGH END SUPPORT

KOR HE-KØR10102 13.70

PLASTIC WATER FOUNTAIN ROLLER BEARING

KOR HE-KØR10104 2.20

WATER FOUNTAIN HOSE CLAMP

K-Series HE-KØR347 38.90

Spring for M-Series Delivery Gripper

Operator Side HE-M01081 6.70Non-Operator Side HE-M01080 2.40

WATER FOUNTAIN TRAYS

(A) TOM, TOK HE-TØ316 262.00(B) GTO 46 Old style (ser # 650058-654211) HE-46316-ØS 184.00(C) GTO 46 New style (ser # 656798-698328) HE-46316-NS 184.00

BUFFER SPRING - Windmill 10x15, 13x18

For roller carriageHE-WI444 32.90

WATER CLUTCH ASSEMBLY - GTO 46 & 52

HE-46418 90.00

OVER RUNNING CLUTCH LEVER ASSEMBLY - GTO 46 & 52

Complete - Ink unit HE-46259 599.90(A) Lever & knob assembly P-320416 32.00(B) Collar - without pins P-6785 64.80(C) Bearing race HE-46261 51.80(D) One way clutch bearing P-3454 389.90(E) Collar - with pins P-6784 64.80(F) Washer - bearing retainer P-2720 .60(G) Belleville washer P-11833 6.90

A B C

OVER RUNNING CLUTCH ASSEMBLY - GTO 46 & 52

Complete (INK) HE-52226 362.90Complete (WATER) HE-52370 440.00

(A) Sleeve HE-52226-S 82.90(B) One way clutch bearing P-3458 109.90(C) Housing only (Not Sold Alone) - - - - - (D) Pin P-4792 1.80(E) Washer P-2720 .60(F) Retaining ring P-10752 1.10

TEFLON SEALS SETS For Quickmaster 46 (set includes 1 ea. left / right hand)

(A) 95mm From end to end P-31161 48.80(B) 102 mm From end to end P-31181 49.80

TEFLON SEAL PACKS(A) Pack of 5 sets P-31161-5 236.00(A) Pack of 10 sets P-31161-10 462.00

(B) Pack of 5 sets P-31181-5 236.00(B) Pack of 10 sets P-31181-10 462.00

TEFLON SEALS - GTO 46 / 52 - For use on Varn units.1 Pack only (2 pcs.) P-30712 19.90Set of 5 packs P-31168 97.50Set of 10 packs P-31169 188.90

TEFLON SEALS - TOK / TOM - For use on Heidelberg dampening units1 Pack only (2 pcs.) P-30713 18.90Set of 5 packs P-30833 89.50Set of 10 packs P-30834 174.90

**1 pack consists of: (1) Right hand seal and (1) Left hand seal.

DAMPENING FELTS

QUICKMASTER P-11739 4.70QUICKMASTER DI P-11740 9.50

ANGLE - Paper stripper.GTO 46 & 52 HE-462301 229.90

HOLD DOWN STRAPS For HE-462301 shown at top left column, this page.

GTO 46 / 52 HE-462281 26.90

SPRING CLIP For HE-462281 shown above.

GTO 46 / 52 HE-462321 .90

GRIPPER FINGER - GTO 46/52, K-Seriesw/o Urethane HE-521050 1.50with Urethane HE-521020 9.90


PART # PART #

28


GRIPPER BAR ASSEMBLIES - GTO 46/52, K-Series

Complete (GTO 46) HE-460990 949.90Complete (GTO 52) HE-520990 999.90Complete (KOR, KORA, KORD 62) HE-KØR0990 1,200.00Complete (KORD 64) HE-KØRD0990 1,330.00Complete (KORS) HE-KØRS0990 1,750.00

(A) Anvil (GTO 46) HE-461090 459.90Anvil (GTO 52) HE-521090 483.90Anvil (KOR, KORA, KORD 62) HE-KØR1090 560.00Anvil (KORD 64) HE-KØRD1090 554.90Anvil (KORS) HE-KØRS1090 664.90

(B) Shaft (GTO 46) HE-461060 65.80Shaft (GTO 52) HE-521060 63.90Shaft (KOR, KORA, KORD 62) HE-KØR1060 108.90Shaft (KORD 64) HE-KØRD1060 109.80Shaft (KORS) HE-KØRS1060 109.80

(C) *Holder assembly HE-521000 47.00(D) **Holder HE-521061 26.90(E) **Finger with urethane HE-521020 9.90(F) **Backing plate HE-521062 3.00(G) **Holding screw P-2003 .60(H) **Belleville washer P-651 1.00(I) **Shoulder screw P-8161 5.50(J) *Arm assembly (GTO 46 & 52) HE-521040 189.90

*Arm assembly (KOR, KORA, KORD62) HE-KØR1040 120.00*Arm assembly (KORS, KORD 64) HE-KØRD1040 107.80

(K) **Arm only (GTO 46 & 52) HE-521041 119.00**Arm only (KOR, KORA, KORD62) HE-KØR1041 76.90**Arm only (KORS, KORD 64) HE-KØRD1041 76.90

(L) **Cam roller stud (GTO 46&52) P-7159 16.90**Cam roller stud (K series) P-7169 21.00

(M) **Cam roller (GTO 46 & 52) P-11179 38.90**Cam roller (K series) P-6840 32.90

(N) **Pin (GTO 46 & 52) P-373 .60**Pin (K series) P-1894 .60

(O) Collar P-6739 12.00(P) Spring (GTO 46 & 52) HE-521080 4.90(Q) Spring (GTO 52) HE-521085 4.50(R) Pin P-2834 .60(R) Screw (K series) P-2101 .60

*indicates a sub-assembly. **indicates components of a sub-assembly.Note: Item (B) Shaft must be taper reamed for pins in field.

GRIPPER PADS - SPEEDMASTER 72 & 102

(A) For ultraviolet & infrared dryersHE-721061-U 14.90

(B) For standard HE-721061 24.90

GRIPPER PAD RAIL For S-Series gripper bars.

HE-SK1061 19.90

WATER OSCILLATING HOUSING ASSEMBLY

K-SeriesOperators side HE-KØ429 349.80Drive side (shown) HE-KØ431 429.90

GEAR FOR METERING ROLL - QM46

(A) Overall Length: 13.5 mmHE-46555QM 10.00

(B) Overall Length: 22 mmHE-46555QM-UG 72.70

A

B

A

B

GRIPPER BAR ASSEMBLY - TOKComplete HE-T00990 699.90(A) Anvil HE-T01090 520.00(B) Set screw P-2506 .60(C) Collar P-6728 4.00(D) Shaft HE-T01060 49.90(E) Gripper finger HE-T01020 14.90(F) Cap screw P-2112 .60(G) Gripper pad P-11904 3.50(H) Gripper spring HE-T01085 3.50(I) Tension collar P-6734 19.90(J) Set screw P-2512 .60(K) Gripper spring HE-T01080 2.30(L) Taper pin P-2810 .60(M) Stop nut P-2610 .60(N) Gripper operating lever HE-T01041 32.50(O) Washer P-580 .60(P) Ball bearing P-11113 8.00(Q) Screw P-2103 .60(R) Bushing P-3239 3.00

GRIPPER BAR ASSEMBLY - QUICKMASTER 46 & 46DI

COMPLETE (46) HE-460990QM 519.90COMPLETE (46DI) HE-460990QMDI 549.90(A) Anvil (comes with P-11904 (Angled Pad) HE-461090QM 339.80(A) Anvil (comes with P-5631 (Flat Pad) HE-461090QMDI 369.90(B) Set screw P-2506 .60(C) Adjusting collar P-6858 38.90(D) Gripper spring HE-461080QM 9.90(E) Delivery gripper for 46 HE-461020QM 23.90(E) Delivery gripper for 46DI HE-461020QMDI 23.90(F) Screw P-2112 .60(G) Gripper shaft HE-461060QM 68.90(H) Taper pin P-2810 .60

GRIPPER LEVER ASSEMBLY HE-461040QM 49.90(Consists of I thru M - also included with complete assembly)

• (I) Screw P-2103 .60• (J) Washer P-5569 .60• (K) Ball bearing P-11113 8.00• (L) Gripper lever only HE-461041QM 37.90

(M) Stop nut P-2610 .60(N) Rubber pad (Flat) P-11904 3.50(N) Rubber pad (Angled) P-5631 5.00

GRIPPER BAR ASSEMBLY - WINDMILL

Complete 10 X 15 HE-WI0990-15 540.00Complete 13 X 18 HE-WI0990-18 599.90

SCREW - For gripper bar operating arm HE-T1307 5.90

PART # PART #



GRIPPER BAR ASSEMBLYCOMPLETE (Speedmaster 72) ........................... HE-720990 3,999.00COMPLETE (Speedmaster 102) ......................... HE-1020990-U 3,999.00(A) Chain link - 4 ea. ......................................... P-8715 39.90(B-1) Carrier link assembly - operators side ........ HE-720991 320.00(B-1) Carrier link assembly - operators side ........ HE-1020991 289.70(B-2) Carrier link assembly - non-oper. side ........ HE-720992 320.00(B-2) Carrier link assembly - non-oper. side ........ HE-1020992 289.70

- Link only - for (B-1) ................................... HE-720991-L 196.00- Link only - for (B-1) ................................... HE-1020991-L 212.80- Link only - for (B-2) ................................... HE-720992-L 196.00- Link only - for (B-2) ................................... HE-1020992-L 212.80- Inner chain link - 2 for each assembly ....... P-8715 39.90- Needle bearing ......................................... P-3461 11.00- Dowel pin for P-8715 - 2 for each assy...... P-2898 2.80- Grease fitting ............................................ P-3672 1.30

(C) Washer ....................................................... P-2738 11.40(D) Screw.......................................................... P-2103 .60(E) Clamping piece ........................................... HE-721066 34.00(F) Finger ......................................................... HE-721020 139.90(G) Gripper supporting shaft.............................. HE-721060 329.90(G) Gripper supporting shaft.............................. HE-1021060 489.90(H) Center pivot bearing.................................... HE-721092 124.00( I ) Gripper operating lever ............................... HE-721040 189.90(J) Taper pin - 3 per complete assembly ........... P-2865 1.40(K) Cam roller ................................................... P-6871 66.20(L) Set screw .................................................... P-10017 .60(M) Spring guide................................................ P-2970 37.90(N) Pin .............................................................. P-4768 19.80(O) E-Ring......................................................... P-2759 .60(P) Clamp ......................................................... HE-721067 40.00(Q) Clamping piece ........................................... HE-721065 31.00

- Screw ....................................................... P-2103 .60- Nut............................................................ P-2603 .60- Lockwasher .............................................. P-10836 .60

(R) Screw.......................................................... P-2143 .60(S) Gripper pad ................................................. HE-721061-U 14.90(T) Clamp (also in S-Series) ............................. HE-721064 34.00(U) Shaft ........................................................... HE-721090 399.90(U) Shaft ........................................................... HE-1021090 450.00

CARRIER LINKS - K/M/GTO Series(A) M-Series - wide attachment P-8739 44.90(B) M-Series - short attachment P-8740 44.90(C) K-Series - operators side P-8732 44.90(C) K-Series - non-operators side P-8742 44.90(D) Star rod carrier link (K/S) P-8734 44.90(E) GTO 46/52 HE-521100-A

GRIPPER CHAIN CONNECTING LINKS(A) KOR, KORD, KORS / M-Series P-8761 9.50(B) KOR, KORD, KORS (offset link) P-8762 13.90(C) Connecting plate P-8712-P 8.50

AB1 C D E F G H I

B2

KL

MNO

PQRS

T

U

J

A B C

GRIPPER CHAINS

TOK (set) HE-T01100 115.00GTO 46 / 52 (set) HE-521100 219.00KOR (set) HE-KØR1100 2,200.00KORD (set) HE-KØRD1100 2,200.00KORS (set) HE-KØRS1100 1,199.00MO (set) HE-M01100 691.90SPEEDMASTER 72/102 HE-721100 207.00SORD HE-SØRD1100 219.90QUICKMASTER 46 (set) HE-461100QM 249.90QUICKMASTER 46DI (set) HE-461100DI

GRIPPER BAR ASSEMBLY CARRIER LINKSSPEEDMASTER 72 & 102

Complete (oper. side) HE-720991 320.00Complete (non-oper. side) HE-720992 320.00

(A) Link only (oper. side) HE-720991-L 196.00(A) Link only (non-oper. side) HE-720992-L 196.00(B) Inner chain link P-8715 39.90(C) Needle bearing P-3461 11.00(D) Dowel pin P-2898 2.80(E) Grease fitting P-3672 1.30

SHEET STOPS

1) KORD 62 ........................................................ HE-KØRD2281-62 34.00(for ser. #335790 & below, otherwise use HE-KØRD2282-64.)

2) KORD 62 & 64 ................................................ HE-KØRD2282-62 34.00(for ser. #335791 & above, otherwise use HE-KØRD2282-62.)

3) KORD 64 ........................................................ HE-KØRD2281-64 34.90

4) KORD 64 ........................................................ HE-KØRD2282-64 34.00for ser. #335791 and above, otherwise use HE-KØRD2282-62.)

5) KORA, KORD-64, KORS (front - side)............. HE-KØRD2284 49.90

6) KORA, KORD-62 (front - center) ..................... HE-KØRD2283-62 42.00

7) KORD-64, KORS (front - center) ..................... HE-KØRD2283-64 49.90

STRIPPER FINGER ............................................ HE-KS15112 2.90

STAR ROD BRUSH ASSY.

Complete P-30842 12.90Brush only P-30842-B 8.50Collar only P-30842-C 4.50Rubber O-ring P-553 .60

STAR ROD ASSEMBLIES

GTO 52 HE-523170 21.90KOR, KORA, KORD 62 HE-KØRD3170-62 77.90KORD 64 HE-KØRD3170-64 94.00M (series) HE-MØ3170 64.90SORDZ HE-SD3170 82.90SORZ HE-SR3170 87.90SORKZ HE-SK3170 87.90SORMZ / SPEEDMASTER 72 HE-SM3170 87.90SORSZ / SPEEDMASTER 102 HE-SS3170 92.50

NOTE: THESE DO NOT COME WITH BRUSHES OR WHEELS

D

EA

B

C

1 2 3

6 7

Stripper Finger

4 5


PART # PART #

30


POWDER TUBE ASSEMBLY

Complete (short tube)......................................... HE-KØR6030 524.90Complete (long tube) .......................................... HE-KØR6040 524.90

Powder tube sub assy. (A - I) ............................ HE-KØR6046 419.80(A) Manifold ...................................................... HE-KØR6050 119.90(B) Screw.......................................................... P-2044 .50(C) Washer ...................................................... P-592 .60(D) Gasket ........................................................ P-6422 1.00(E) Rubber washer............................................ P-11036 5.00(F) Lock nut ...................................................... P-2616 1.10(G) Powder tube guide ...................................... HE-KØR6051 49.90(H) Stop screw .................................................. P-2351 .60(I) Screw.......................................................... P-2082 .60

Spray nozzle sub assy. (J - M) .......................... HE-KØR6047 147.80(J) Nozzle......................................................... HE-KØR6056 42.00(K) Screw.......................................................... P-2921 6.90(L) Spring ......................................................... P-15601 3.90(M) Nozzle tube................................................. HE-KØR6055 119.90

Powder tube sub assy. - short (N - R) ............... HE-KØR6035 99.90

Powder tube sub assy. - long (N - R) ................ HE-KØR6045 120.00(N) Short tube (for HE-KØR6030) ..................... HE-KØR6052 65.80(N) Long tube (for HE-KØR6040) ..................... HE-KØR6053 68.00(O) Nut .............................................................. P-2681 .60(P) Compression nut with gasket ...................... P-2941 27.90(Q) Guide collar................................................. HE-KØR6054 65.80(R) Set screw .................................................... P-2499 .60

GUIDE WHEEL KIT - GTO 52

Complete HE-521327 25.80 Wheel only HE-521328 15.00 O-Ring P-11778 2.10 Set screw P-2580 .60

8 Watt FLOURESCENT BULB - GTO 46 / 52, TOM / TOK P-9743 9.00

14 Watt FLOURESCENT BULB - KORD 64 P-9726 22.00

BRASS FILTER SCREENS

Windmill Platens (24mm collar) P-9410 25.90GTO 46 & 52 (28 mm collar) P-9411 25.90GTO 46/52, Windmill (38 mm collar) P-9412 29.90

SLIP RING BRUSHES

K-Series (shown) P-9428 10.90S-Series P-9438 10.70S-Series P-9439 5.60Paired Collector Brush P-9429 61.90

PUMP VANE P-9444 59.90

CARBON BRUSHES

Carbon Brush P-9431 69.80Carbon Brush P-9432 4.00S-Series P-9769 38.90Speedmaster P-9433 69.90Speedmaster 102Z P-9434 69.90Speedmaster 102 P-9435 39.90Speedmaster 102V P-9436 29.90102D+L 102V (Main motor) P-9437 24.90TOK/TOM (Motor) P-9440 20.00

ROLLER SNAP SWITCH - All S-SeriesLocated on operators side outer delivery frame

P-9805 42.90

LIMIT SWITCHES

(A) GTO 46/52, M/S Series, Speedmaster 72/102 P-9836 124.90

(B) GTO 46/52, M/S Series, Speedmaster 72/102 P-9837 99.80

(C) GTO 52, M-Series, Spdmst 102 (snap action) P-9838 119.90(C) M-Series (slow action) P-9839 69.75

(D) GTO 46 / 52 - Located behind blower tubes P-4074 49.90

VARIABLE SPEED PULLEY For K-Series

P-4291 1,598.00

COMPRESSION SPRING - WINDMILL 10 x 15For variable speed control.

HE-WI046 85.70

BOWDEN CABLE

WINDMILL HE-WI3101 119.90

DELIVERY TABLE CABLE

K-Series HE-KØ971 55.00SB-Series HE-S1539 43.90

Lay Gauge Pin Kit

Set of 5 P-31133

Starwheel

(A) Star/Pointed Surface P-30842-0(for K/S/M series)

(B) Knurled/Dimpled Surface P-30842-GT0(GT0 46/52)

(B) Knurled/Dimpled Surface P-30842-K(for K/S/M series)

(C) Smooth/Plain Surface P-30842-S(for K/S/M series)

A B C D

A

B

C

PART # PART #



PNEUMATIC SPRING For Speedmaster 102

Safety guard (11-7/8” end to end) P-29990 101.20Delivery (16-5/8” end to end) P-29991 136.30

BLOW DOWN FAN For Speedmaster 102 delivery

Terminal connection P-4204 225.90Wire connection P-4205 225.90

EMERGENCY KITS

TOK/TOM P-31143 239.80Consists of: 6 Impression gripper fingers /1 Wash-up blade / 12 Sucker feet / 1 Set of teflon seals.

QUICKMASTER 46 P-31144 289.80 Consists of: 8 Impression gripper fingers / 1 Wash-up blade / 12 Sucker feet / 1 Dampening felt / 1 Tape track

QUICKMASTER DI46 P-31145 279.80Consists of: 8 Impression gripper fingers / 1 Wash-up blade / 12 Sucker feet / 1 Dampening felt

HARDWARE EMERGENCY KITS

HAS YOUR PRESS EVER BEEN DOWN DUE TO A SIMPLE PIN OR SPRING? YOU CAN ELIMINATE COSTLY DOWN TIME IN MINUTES WITH YOUR OWN EMERGENCY KIT DESIGNED TO CONVENIENTLY FIT IN YOUR DESK DRAWER. EACH KIT COMES IN IT’S OWN MULTI-COMPARTMENT RECLOSABLE BOX FOR QUICK, EASY SELECTION AND STORAGE. PART NUMBERS FOR THE INDIVIDUAL ITEMS ARE ALSO INCLUDED INSIDE.

MASTER KIT All kits below P-30397 219.90NUT KIT 43 pcs. P-30392 21.50WASHER KIT 60 pcs. P-30396 40.00SCREW KIT 168 pcs. P-30393 96.00RING KIT 47 pcs. P-30395 28.90PIN KIT 100 pcs. P-30394 37.50

CAM FOLLOWERS

GTO 46 (A) Transfer & imp. cylinder / gripper shaft. ....... P-3441 109.90(B) Side lay shaft. ............................................. P-4368 39.00

GTO 52(A) Transfer & impression cylinder & storage drum

/ gripper shaft.............................................. P-3441 109.90

K-SERIES(C) Imp. cyl.shaft

/ sucker bar mechanism Outer lever. ........... P-6870 109.90

M-SERIES(D) Transfer & impression cylinder & storage drum

/ gripper shaft.............................................. P-3416 197.90(E) Reversing drum........................................... P-3443 163.00(F) Register feed drum / gripper shaft. .............. P-3444 110.00

SORZ / SORDZ / SORKZ / SORMZ / SORSZ(G) Register feed drum / gripper shaft

..(cam facing cylinder O.S. & D.S.) .............. P-3442 119.00(H) Register feed drum / gripper shaft

..(cam facing side frames O.S & D.S.) ......... P-3445 155.00(F) Imp. cyl. & storage drum / gripper shaft. ...... P-3444 110.00

SPEEDMASTER 72 / 102(G) Register feed drum/ gripper shaft

..(cam facing cylinder O.S. & D.S.) .............. P-3442 119.00(H) Register feed drum / gripper shaft

..(cam facing side frames O.S. & D.S.) ........ P-3445 155.00(F) Transfer & imp. cylinder / gripper shaft. ....... P-3444 110.00(H) Transfer gripper........................................... P-3445 155.00

SPEEDMASTER 74(I) Delivery table. ............................................. P-3439 69.90

SPEEDMASTER 102(J) Gripper opening lever on del. gripper bars. . P-6871 66.20(G) On lever (OEM #71-010-110) / inking unit. .. P-3442 119.00

QUICKMASTER(A) Impression cylinder / gripper shaft. ............. P-3441 109.90

GTO 46INK ROLLER KIT P-30457 741.85Consists of:(6) Blue Distributor / Ductor P-46H10B 86.25(1) Red Form P-46H10R 89.65(1) White Form P-46H10W 86.25(1) Yellow Form P-46H10Y 87.50

KORD 62INK ROLLER KIT P-31656 1,597.05Consists of:(2) Blue Form / Distributor P-30916 203.90(3) Red Form / Distributor / Ductor P-30918 181.90(2) White Form / Distributor / Ductor P-30917 181.90(2) Brown Form / Distributor / Ductor P-30919 181.90

QUICKAMSTER 46 (1ST. UNIT)INK ROLLER KIT P-31735 755.25Consists of:(1) Yellow 1st. Ink Form P-34H10 128.00(1) Blue 2nd. Ink Form P-34H11 106.00(1) Black 3rd. Ink Form P-34H13 222.00(1) Black Ink Transfer Roll #1 P-34H20 86.00(1) Black Ink Transfer Roll #2 P-34H21 86.00(1) Black Ink Transfer Roll #3 P-34H22 81.00(1) Black Ductor P-34H30 86.00

A B C D E F G

H I J

Muestrario de refacciones Heidelberg®equiposgraficos.com/images/Catalogo_refacciones... · 2021....

Documents

Transcript of Muestrario de refacciones Heidelberg®equiposgraficos.com/images/Catalogo_refacciones... · 2021....