MSP WEBPRO INSTRUCTION MANUAL Rev 2.0 18-Feb … - Instruction … · · 2011-02-18MSP WEBPRO...

MSP WEBPRO INSTRUCTION MANUAL

Copyright © 2008 Monitoring Solution Providers Pte Ltd All rights reserved of 11

MSP WEBPRO INSTRUCTION MANUAL Rev 2.0 18-Feb-2011 Monitoring Solution Providers Pte Ltd Monitoring Solution Providers 33 Ubi Avenue 3 #05-31 Vertex Singapore 408868 Tel: (65) 6747 9766 Fax: (65) 6458 0824 [email protected] [email protected] DISCLAIMER This document is Copyright © 2011 by the Monitoring Solution Providers Pte Ltd. MSP retains full copyright ownership, rights and protection in all material contained in this document. You may use this document for your own purposes. You may distribute this document to other persons provided that you attribute the document as having been generated by MSP and that the document is available free of charge on the MSP WebPro website. Though MSP believes reasonable efforts have been made to ensure the accuracy of the information contained in this document, it may include inaccuracies or typographical errors and may be changed or updated without notice. It is intended for discussion and educational purposes only and is provided "AS IS" WITHOUT WARRANTY OF ANY KIND AND RELIANCE ON ANY INFORMATION PRESENTED IS AT YOUR OWN RISK. In no event shall MSP be liable for any direct, indirect, punitive, incidental, special, or consequential damages or damages for loss of profits, revenue, data, down time, or use, arising out of or in any way connected with the use of this document or performance of any services, whether based on contract, tort, negligence, strict liability or otherwise. If you are dissatisfied with any portion of this document, or with any of these terms of use, your sole and exclusive remedy is to discontinue using this document.

mailto:[email protected]




TABLE OF CONTENTS

I. How to Get There 3

II. How to Sign Up 3

III. How to Log In 4

IV. How to View a Cycle 5

V. How to Explore the Site Layout 6

VI. How to Download the Report 7

VII. How to Open the Section View 8

VIII. How to Open the Prism Graph View 9

IX. How to Know If There are Any Alarms 10

X. How to Log Out 11



I. HOW TO GET THERE Enter http://www.mspsystem.com/mspviewer on your internet browser’s address bar to go directly to the MSP WebPro website.

II. HOW TO SIGN UP

If you don’t have your log in information yet, you must first sign up by clicking the “sign up” button to download the User Access Request Form (document is in pdf format so you must have an Adobe Acrobat Reader installed on your computer to open the file).

Fill up the required information on the document and send it back via fax (6458 0824) or email ([email protected]) to MSP.

http://www.mspsystem.com/mspviewer




III. HOW TO LOG IN To log in to the MSP WebPro website, key in your user name and password into the two input fields on the MSP WebPro log in page and click the “log in” button.

NOTE: MSP WebPro requires an SVG Viewer to be installed on your computer for the site layout and monitoring data to be displayed on your internet browser. To download the SVG viewer click on the button icon at the bottom of the log in page and run the installation on your computer. MSP WebPro will prompt you to install SVG viewer upon



logging in if you haven’t installed it yet. This is only a one time process and will not be required again on your next log in.

IV. HOW TO VIEW A CYCLE

By default, the project’s latest cycle (most current) will be displayed on the MSP WebPro. To view the monitoring data on a particular cycle, first select the project on the first dropdown list, and then select the cycle – date on the next dropdown list. Wait for the web page to reload and the site layout will be updated to display the selected cycle’s monitoring data.



V. HOW TO EXPLORE THE SITE LAYOUT

At the bottom right hand corner of the site layout map, you will find the controls for exploring the site layout.

To zoom in, click the plus sign (+) icon. To zoom out, click the minus sign (-) icon. To reload the site map to its initial state, click the refresh icon. To move the panning box (red rectangular lens) to the center of the map, click

the bull’s eye icon. To scroll around the map, drag the panning box with your mouse pointer or

click the arrow icons at the corners and sides of the control panel.

NOTE: You may perform a real-time zooming on the map by clicking and holding the mouse pointer (keep the button pressed) on the zoom in or zoom out icon. The label on the top right corner of the control panel displays the current magnification of the site map (e.g. 10x for tenfold magnification).



VI. HOW TO DOWNLOAD THE REPORT

If you wish to download the report of the monitoring data for the selected project, simply select the prism position index on the third dropdown list (next to the cycle-date) and click either the “history” or “profile” button. If “ALL” is available on the prism position list, you may select this to download all the monitoring data of all the prisms of the selected project. The history and profile reports normally include a two-week period of monitoring data depending on the duration which is viewable to the user.

NOTE: The report documents are in Microsoft Excel format so you will need this software installed on your computer to open the downloaded file. The history and profile reports list the monitoring data within the “viewable” period and plot the corresponding charts to verify the trend on the prism displacements.



VII. HOW TO OPEN THE SECTION VIEW

Prisms on each chainage may be viewed on the tunnel’s section view. To open the section view, select the chainage on the dropdown list next to report download buttons and click the “section” button.

NOTE: To print or save the section view image on your computer, right-click on the section view window and select the picture options from the context (popup) menu.



VIII. HOW TO OPEN THE PRISM GRAPH VIEW

You may view the trend of monitoring data for each prism by opening the prism history chart or graph view. To do this, select the prism name from the rightmost dropdown list and click on the “graph” button next to it. This will open a window with the selected prism’s data plotted on a history chart for the entire viewable (normally two-week) period.

NOTE: To print or save the prism history chart image on your computer, right-click on the graph view window and select the picture options from the context (popup) menu.



IX. HOW TO KNOW IF THERE ARE ANY ALARMS

There are three levels of alarm triggers, each of which corresponds to a specific color. The first (and lowest) alarm level is green, second alarm level is yellow, and the third (and highest) alarm level is red. Any of the prisms on the site map will be displayed as a blinking prism with its color corresponding to the alarm level it reached.

The maximum reading on the bottom right corner next to the alarm level triggers will also have a background color corresponding to the alarm level it triggered. If the maximum reading’s background color is blue, no prism for that particular cycle has reached an alarm level.



X. HOW TO LOG OUT

To end your session, click the button icon at the bottom of the web page and you will be logged out of MSP WebPro.

MSP WEBPRO INSTRUCTION MANUAL Rev 2.0 18-Feb … - Instruction … · · 2011-02-18MSP WEBPRO...

Documents

Transcript of MSP WEBPRO INSTRUCTION MANUAL Rev 2.0 18-Feb … - Instruction … · · 2011-02-18MSP WEBPRO...