M.sc rc-11
-
Upload
rizwan-khurram -
Category
Documents
-
view
23 -
download
2
Transcript of M.sc rc-11
![Page 1: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/1.jpg)
First Approximate Method Of Design For Compression Failure
Step 3: Calculate eb from the moment equation in terms of Ast.
Pnb × eb = 0.85 fc′bab +
−
22ah ( )df
Adhf
Ay
sty
st ′′+
′−
222
For symmetric sections, h/2 − d′ = d″
Pnb × eb = 0.85 fc′bab + Ast fy (XVI)
−
22ah
′− dh
2
Step 4: Calculate Po in terms of Ast.
Po = φ [0.85 fc′ (Ag − Ast) + Ast fy] (XV)
![Page 2: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/2.jpg)
Step 5: The interaction diagram in the compression region is assumed to be a straight line from the safe purely axial load point (Po) to safe balanced point (Pb).
Pu
Po
Design CurveC
Pb
Pu × ePbeb
Pu e
Pu
A
B
Fig. 14.19. Approximate Design Interaction Curve For Compression Region.
![Page 3: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/3.jpg)
Slope of line = bb
bo
ePPP −
Hence for any point ‘C’, Pu = Po − (Pu e)bb
bo
ePPP −
Pu = (XVI)
bb
o
o
ee
PP
P
−+ 11
The values of Po and Pb may be put in terms of Ast to form a quadratic equation in terms of Ast.
The resulting equation may be solved for the unknown steel area.
However, the solution is still lengthy and difficult to solve for design.
![Page 4: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/4.jpg)
Whitney’s Empirical Equation
Assumptions:
The column has a rectangular cross-section with reinforcement placed in two layers parallel to the axis of bending at equal distances from this axis.
The compression reinforcement has yielded. This is true for small eccentricities.
The area of concrete displaced by the compression steel may be neglected.
![Page 5: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/5.jpg)
A straight line can represent the interaction diagram for compression failures starting from the point corresponding to the pure axial load capacity Pno to the point corresponding to a balanced failure.
The depth of the compression stress block for a balanced failure is ab = β1cb.
From strain compatibility, assuming that fc′ ≤ 28 MPaand fy = 420 MPa, we get,
ab = β1 dyf+600
600
= 0.85 d ≅ 0.50 d420600
600+
![Page 6: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/6.jpg)
Summing the moments about the tension reinforcement at balanced stage gives the following:
Pnb = Cs′ (d − d′ ) + Cc (d − ab/2)
−+
2hdeb
d − h/2 = (d − d′ ) / 2, Cs′ = As′ fy, Cc = 0.85 fc′ b ab
Pnb
= As′ fy (d − d′ ) + 0.85 fc′ b (0.50d)
′−
+2
ddeb
−
250.0 dd
Pnb = + 2
22
2
319.0
dhdde
dhbdf
b
c
×′−
+
×′
5.0+′−
′
dde
fA ys
![Page 7: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/7.jpg)
Pnb = + (XVII)( )22 2
319.0
dhdd
dhe
hbfb
c
′−+
′
5.0+′−
′
dde
fA ys
This equation is basically valid for balanced failure.
To make it valid for smaller eccentricities, the above equation is forced to pass through the value of Pno at e = 0.
Also to make it a general equation, e is used in place of eband Pn is used in place of Pnb.
For e = 0, Eq. XVII gives:
Pno = + 2As′ fy (XVIII)( )22
319.0
dhddhbfc
′−′
![Page 8: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/8.jpg)
Actually, Pno = 0.85fc′ b h + 2As′ fy (XVIV)
Comparing Eqs. XVIII and XVIV,
= 0.85 fc′ b h( )22
319.0
dhddhbfc
′−′
= 0.375 (XVV)( )
22dhdd ′−
From XVII: Pn = + 375.0
319.0
2 +
′
deh
hbfc
dde
fA yst
′−+
21
Pu = φPn for fy = 420 MPa
![Page 9: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/9.jpg)
In general, the formula for all grades of steel becomes:
Pn = +
85.02
αα
+
′
deh
hbfc
dde
fA yst
′−+
21
whereα = 0.408 − 0.00021 fy
Example 14.3: A 375×450 mm tied column is to be reinforced symmetrically by bars placed in two opposite faces of the section. fc′ = 20 MPa, fy = 420 MPa, d′ = 65 mm and d = 450 − 65 = 385 mm. Determine the steel areas required for the column to support the following ultimate loads:
1. 675 kN at e = 450 mm, 2. 1180 kN at e = 200 mm.
![Page 10: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/10.jpg)
Solution:
ab = β1 d = 192.5 mmyf+600
600
εs′ (balanced condition) = (0.003)b
b
ada ′− 1β
= 0.00214 > = 0.0021s
y
Ef
∴ Compression steel is yielding at balanced stage,
fs′ = fy
Pnb ≈ 0.85×200×375×192.5 + As′ fy − As fy= 1227.2 kN
![Page 11: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/11.jpg)
Pb = 0.65 Pnb = 797.7 kN
1. Pu = 675 kN, e = 450 mm
Pu < Pb ⇒ tension failure ⇒ fs = fy
φappr. =nb
u
PP
49.0 −
= = 0.762.12274
6759.0×
−
Assuming fs′ = fy, the load equation becomes:
= 0.85 × 20 × 375 a ∴ a = 139.3 mm76.0675000
![Page 12: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/12.jpg)
εs′ = 0.003 = 0.00181 < εyada ′− 1β
∴ Compression steel is not yielding.
Let fs′ = (εs′ Es + Previous fs′ ) / 2= (0.00181 × 200,000 + 420) / 2 = 391 MPa
From the moment equation about the plastic centroid,
= 0.85 (20)(375)(139.3)(225 − 139.3/2)
+ (391)(225 − 65) + (420)(225 − 65)
76.0450675000×
2stA
2stA
Ast = 4034 mm2
![Page 13: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/13.jpg)
2nd Trial
= 0.85 × 20 × 375 a + (391) − (420)76.0
6750002
40342
4034
∴ a = 148.5 mm
εs′ = 0.003 = 0.00188 < εyada ′− 1β
∴ Compression steel is not yielding.
Let fs′ = (εs′ Es + Previous fs′ ) / 2
= (0.00188 × 200,000 + 391) / 2 = 384 MPa
From the moment equation about the plastic centroid,we get:
![Page 14: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/14.jpg)
= 0.85 (20)(375)(148.5)(225 − 148.5/2)
+ (384)(225 − 65) + (420)(225 − 65)
76.0450675000×
2stA
2stA
Ast = 3995 mm2
3rd Trial
= 0.85 × 20 × 375 a + (384) − (420)76.0
6750002
39952
3995
∴ a = 150.6 mm
εs′ = 0.003 = 0.00190 < εyada ′− 1β
∴ Compression steel is not yielding.
![Page 15: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/15.jpg)
Let fs′ = (εs′ Es + Previous fs′ ) / 2
= (0.00190 × 200,000 + 384) / 2 = 382 MPa
From the moment equation about the plastic centroid,
= 0.85 (20)(375)(150.6)(225 − 150.6/2)
+ (382)(225 − 65) + (420)(225 − 65)
76.0450675000×
2stA
2stA
Ast = 3989 mm2
4th Trial
Ast = 3990 mm2
![Page 16: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/16.jpg)
As an alternate, exact solution may be carried out following almost the same procedure as that for the compression failure.
εs = 0.003 = 0.00349aad −1β
φ = = 0.77)(005.0
25.065.0 yty
εεε
−−
+
This value is sufficiently close to the assumed value, and is on the safe side.
2. Pu = 1180 kN, e = 200 mm
Pu > Pb ⇒ φ = 0.65
![Page 17: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/17.jpg)
A. EXACT SOLUTION
Assuming the compression to be yielding, the load equation may be written as follows:
= 65.0000,1180 ( )( )( ) ( )420
23752085.0 stA
a + ( ) ( )
−
−a
aAst 38585.06002
Ast (210 − 300 ) = 1,815,385 − 6375 aa
a−25.327
∴ = (I)a
Ast
981755106375385,815,1
−−
aa
From moment equation, we get,
![Page 18: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/18.jpg)
= 0.85(20)(375)(a)(225 − 0.5a)
+ (420)(160) + (600) (160)
65.0200000,1180 ×
2stA
2stA ( )
−
aa38585.0
∴ = (II)aAst
aaa4.14708,15
077,3634.14341875.3 2
−+−
From Eqs. I and II:
F(a) = 0.00163 a3 − 1.1363 a2 + 452.27 a − 64161 = 0F′ (a) = 0.00489 a2 − 2.2726 a + 452.27
Assume ao = h / 2 = 225 mm
![Page 19: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/19.jpg)
a1 = ao −( )( )o
o
aFaF′
= 225 − = 232.2 mm( )
49.1887.1358−
a2 = a1 −( )( )1
1
aFaF′
= 232.2 − = 232.2 mm( )22.18828.1−
εs′ = 0.003 = 0.00229 > εy
(Compression steel is yielding)
ada ′− 1β
From Eq. I: Ast = 3843 mm2
![Page 20: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/20.jpg)
B. FIRST APPROXIMATE METHOD
Try at home. Results like those given below will be obtained:
1180 =
st
st
st
AA
A
05476.075.1282001
7.797273.07.1864
1
273.07.1864
+
−
++
+
− 543.2Ast − 15,218,662 = 02stA
Ast = 4182 mm2 (8.83% greater than actual result)
C. USING WHITNEY’S EQUATION
α = 0.408 − 0.00021 fy= 0.408 − 0.00021 × 420 = 0.32
![Page 21: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/21.jpg)
Pn = + 85.02
αα
+
′
deh
hbfc
dde
fA yst
′−+
21
=65.0000,1180 ( )( )( )( )
( )( )( )
( )( )( )
32020021
420
85.032.0
385450200
4503752032.0
2 ++
+
stA
∴ Ast = 3844 mm2
(can be on unsafe side in some cases)
![Page 22: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/22.jpg)
ANALYSIS OF RECTANGULAR COLUMNSHAVING BARS AT FOUR FACES
For a general bar ‘i’ in the section, from the strain diagram of Fig. 14.20,
εsi = 0.003 ; di < c ⇒ Compressive strains denoted by negative signc
cdi −
di > c ⇒ Tensile strains denoted by positive sign
The stresses can be calculated according to the following three possibilities:
1. If, εsi ≥ , fsi = fy (tensile)s
y
Ef
![Page 23: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/23.jpg)
e
h/2 h/2
Pb
ith bar
di
c
εsi
εc=0.003a
fsi
0.85fc′
P
CcAsi fsi
Strain Diagram
Equivalent Stress Diagram
Force Diagram
Pn
Fig. 14.20. General Analysis of a Short Column.
![Page 24: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/24.jpg)
2. If, εsi ≤ – , fsi = – (fy − 0.85 fc′)(compressive, exact)s
y
Ef
fsi = – fy (compressive, approximate)
3. Otherwise, fsi = εsi Es + 0.85 fc′(compressive, exact)
fsi = εsi Es (compressive, approximate)
Cc = − 0.85 fc′ a b
Load equation Pn = − Cc − ∑=
n
isisi Af
1
![Page 25: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/25.jpg)
Moment equation Pn × e
= − Cc − ( h/2 − di)
−
22ah ∑
=
n
isisi Af
1
= Cc + (di – h/2)
−
22ha ∑
=
n
isisi Af
1
To find out the load carrying capacity of such a column at a known eccentricity, trial method is suitable. The general procedure is summarized below:
1. Select ‘c’ and ‘a’ arbitrarily.2. Find fs in all the steel bars.3. Calculate Pn from the load equation.
![Page 26: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/26.jpg)
4. Calculate Pn from the moment equation knowing the eccentricity.5. Repeat steps 1,2,3 and 4 until the values of Pnin steps 3 and 4 become the same.
Example 14.4: The column shown in Fig. 14.21 is reinforced with 10 # 25 (US Customary) bars. Find Pnand Mn, if the neutral axis is known to be at 500 mm from the right face. fc′ = 25 MPa, fy = 520 MPa, d′ = 67.5 mm and d = 675 − 67.5 = 607.5 mm.
Solution:Using strain diagram of Fig. 14.21, Es = 200,000 MPa, and c = 500 mm:
![Page 27: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/27.jpg)
εsi = 0.003 ; εy = 0.0026;
0.85 fc′ = 21.25 MPa
ccdi −
675
180 180
Pn375
As4
180
As3 As2 As1
Fig. 14.21. Column Cross-Section For Example 14.4.
![Page 28: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/28.jpg)
εs1 = − 0.002595 fs1 = − 519 MPa (compressive)εs2 = − 0.001515 fs2 = − 303 MPa (compressive)εs3 = − 0.000435 fs3 = − 87 MPa (compressive)εs4 = + 0.000645 fs4 = + 129 MPa (tensile)
d1 = 67.5 mm As1 = 1530 mm2
d2 = 247.5 mm As2 = 1020 mm2
d3 = 427.5 mm As3 = 1020 mm2
d4 = 607.5 mm As4 = 1530 mm2
![Page 29: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/29.jpg)
a = β1c = 425 mmCc = 0.85 × (−25) × 375 × 425 / 1000 = − 3386.7 kN Fsi = fsi × AsiFs1 = (1530) × (− 519) / 1000 = − 794.1 kN Fs2 = (1020) × (− 303) / 1000 = − 309.1 kNFs3 = (1020) × (− 87) / 1000 = − 88.7 kNFs4 = (1530) × (+129) / 1000 = + 197.4 kN
Pn = − Cc − ∑=
n
isisi Af
1
= 3386.7 + 794.1 + 309.1 + 88.7 − 197.4≈ 4381 kN
Mn = Pn × e
= Cc + (di – h/2)
−
22ha ∑
=
n
isisi Af
1
![Page 30: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/30.jpg)
Mn = [(−3386.7)(212.5 − 337.5) + (−794.1)(67.5 −337.5) + (−309.1)(247.5 −337.5) + (−88.7)(427.5 −337. 5)+ (197.4)(607.5 −337.5)] / 1000
= 710.9 kN-m
![Page 31: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/31.jpg)
BIAXIAL BENDINGIn practice many columns are subjected to bending about both principal axes simultaneously.
A typical example is the corner columns of a building.
A failure surface for axial load (Pn) plus biaxial bending (Mnx = Pn ey and Mny = Pn ex) is plotted on the three mutually perpendicular axes, exactly analogous to the failure line for axial load plus uniaxial bending.
Any combination of Pu, Mux and Muy falling inside the design surface can be applied safely, but any point falling outside the surface would represent failure.
![Page 32: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/32.jpg)
ex = eccentricity of load from the plastic centroid parallel to the x-axis
and ey = eccentricity of load from the plastic centroid parallel to the y-axis
Three Types of Interaction Surfaces
1. Surface plotted for parameters Pn, ex and ey(Diagram – A of Fig. 14.22).
2. Surface plotted for parameters 1 / Pn, ex and ey(Diagram – B of Fig. 14.22).
3. Surface plotted for parameters Pn, Mnx and Mny(Diagram – C of Fig. 14.22).
![Page 33: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/33.jpg)
Pn
exey
1 / Pn
exey
Pn
MnyMnx λ
Case-ICase-II
Case-III Interaction Diagram - C
Interaction Diagram - A Interaction Diagram - B
Fig. 14.22. Typical Interaction Surfaces For Biaxial Bending of Columns.
![Page 34: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/34.jpg)
λ = eccentricity angle, defined as the angular distance of load from the y-axis.
= = ye
e1tan −
nx
ny
MM1tan −
θ = counter-clockwise angle of the neutral axis with respect to the y-axis.
Analysis and design of column sections having biaxial bending are lengthy compared to uniaxial bending cases because a trial and adjustment procedure is required to find the inclination of the neutral axis, θ, and the depth of neutral axis, c, satisfying the equilibrium equations. There are two unknowns in this analysis, namely, θ and c, as compared to only one unknown in the uniaxial analysis.
![Page 35: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/35.jpg)
ex
Pn
Y
X
Mnx = Pn ey
Case-II
c
Mny = Pn exc
ey
Pn
Y
X
Case-I
Y Xex ey
h/2
h/2 b/2b/2
Plastic centroid
Y
Case-III
Pn
ey
ex
X
θ
90 − θ
λ
N.A.
Pn
![Page 36: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/36.jpg)
The four possible shapes of the equivalent compressive stress block for Case III, are shown in Fig. 14.24.
Case-1 Case-2 Case-3 Case-4
b
hβ1kyhy
x
ky h
kx b
β1kxb Point of Resultant Cc
Fig. 14.24. Various Concrete Stress Blocks For Biaxial Bending of Columns.
![Page 37: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/37.jpg)
For First Stress Block, we have,
Cc = = 2
))()(85.0( 11 bkhkf xyc ββ′bhkkf yxc
21425.0 β′
y= 0.333 β1 kx b : = 0.333 β1 ky hx
The strain, stress and force diagrams for any one of these cases can be drawn perpendicular to the neutral axis, as shown in Fig. 14.25.
![Page 38: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/38.jpg)
y ex
xkyh
Pn
ey
kxb
12
3 4
ty
ty
tx tx
c
εs4
εc = 0.003
εs3
εs2
εs1a
0.85fc′
fs1
fs2fs3
fs4
P
S1
CcS2
S4
S3
StrainDiagram
StressDiagram
ForceDiagram
θ
bkhk
x
y=θcot
Pn
Fig. 14.25. Strain, Stress and Force Diagrams For Biaxial Bending of a Column Section.
![Page 39: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/39.jpg)
The strain, stress and force diagrams for any one of these cases can be drawn perpendicular to the neutral axis, as shown in Fig. 14.25.
From similar diagrams of the strain diagram, considering compressive strains and stresses to be positive, the following is obtained:
= 003.01sε
ccs dimension- along N.A. from of distance 1ε
= ratio of vertical corresponding distancesThe above is true because lines perpendicular to the neutral axis and the vertical lines are both intersecting a set of parallel lines and hence the ratio between the corresponding intercepts must be equal.
![Page 40: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/40.jpg)
kyh12
3 4
tx
θ
bkhk
ttx
yxx =θcot
Fig.14.26.Calculation of Vertical Dimensions.
ty
= 003.0
1sεhk
tthk
y
yxy −− θcot
![Page 41: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/41.jpg)
εs1 = 0.003
−−
hkt
bkt
y
y
x
x1
Let, dxi = horizontal distance of steel from the compression face
dyi = vertical distance of steel from the compression face
= ty for steels 1 and 2= h − ty for steels 3 and 4
Then, εsi = 0.003
−−
hkd
bkd
y
yi
x
xi1
![Page 42: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/42.jpg)
For example,
εs2 = 0.003
−
−−
hkt
bktb
y
y
x
x1
εs3 = 0.003
−−−
hkth
bkt
y
y
x
x1
εs4 = 0.003
−−
−−
hkth
bktb
y
y
x
x1
It is to be noted that the positive strains indicate compression. The stresses in the steel bars are calculated as follows:
![Page 43: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/43.jpg)
If εsi ≥ fy / Es, fsi = fyor if εsi ≤ −fy / Es, fsi = −fyelse fs1 = εsi Es
The forces in steel bars are calculated as follows:
Si = Asi fsi
The equilibrium equations are then written as follows to calculate the load and the moment capacities:
Pn = Cc + Σ Si
Mnx = Pn ey = Cc + Σ Si
− yh
2
− yidh
2
![Page 44: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/44.jpg)
Mny = Pn ex = Cc + Σ Si
− xb
2
− xidb
2
The appropriate signs should always be substituted into the above equations to get the correct answers.
The procedure to plot the strength interaction curve for a particular value of the eccentricity angle, λ, is as follows:
1. Neutral axis distance from the most heavily compressed corner is selected.
2. Some value of angle θ is selected.
3. The concrete stress resultant and its point of application are determined by using Eqs. I to III.
![Page 45: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/45.jpg)
4. Strains are calculated in all the steel bars by employing Eq. IV.
5. Stresses are determined for the conditions of Eq. V.
6. The values of Pn, Mnx and Mny are evaluated.
7. The value of λ for this trial is determined as tan-1(Mny /Mnx).
8. Steps 2 to 7 are repeated until λ = λt, with some pre-defined tolerance, which gives one point on the curve.
Calculate Mnλ = and plot the point Pn, Mnλ.22nynx MM +
![Page 46: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/46.jpg)
9. The φ-factor is calculated for the maximum tensile strain in any steel bar. If no steel bar is in tension, the value of 0.65 is used.10. A new value of the neutral axis depth is selected and steps 2 to 9 are repeated until full curve is plotted.
APPROXIMATE MEHTODS OF ANALYSIS AND DESIGN FOR BIAXIAL BENDING
Method Of SuperpositionIn this method, the reinforcement required for the two uniaxial bending cases, (Pu, Mux) and (Pu, Muy), is calculated separately and is then added to get the design for the biaxial bending.
![Page 47: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/47.jpg)
Equivalent Uniaxial Eccentricity Method
The biaxial eccentricities, ex and ey, are replaced by an equivalent uniaxial eccentricity, eox, and the column is designed for the uniaxial bending case, (Pn, Pn×eox).
If ex / b ≥ ey / h, eox = ex + α bhey
For 4.0≤′ gc
u
AfP 6.0
720300
5.0 ≥+
′+= y
gc
u fAf
Pα
For 4.0>′ gc
u
AfP 5.0
720300
3.1 ≥+
′−= y
gc
u fAf
Pα
![Page 48: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/48.jpg)
This method has certain restrictions.
Firstly, it is applicable only for columns symmetrical about both the axes and the ratio of their sides (b / h) lying between 0.5 and 2.0.
Secondly, the resulting reinforcement is to be placed in all the four faces of the column.
For the cases when the condition ex / b ≥ ey / h is not satisfied, either the axes may be interchanged (ex becomesey and vice versa) or the equation may be written for eoy.
![Page 49: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/49.jpg)
Bresler Reciprocal Load Method
It is derived from a plane segment inside the interaction surface defined by 1/Pn, ex and ey.
If Pni is the approximate value of the ultimate load in biaxial bending case having eccentricities ex and ey, Pnxis the nominal load strength when only ex is present (ey = 0), Pny is the nominal load strength when only ey is present (ex = 0) and Po is the nominal load strength for concentrically loaded column, the following expression is used to find the strength corresponding to biaxial bending:
![Page 50: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/50.jpg)
onynxni PPPP1111
−+=
The same equation may be modified for the interaction curve with φ-factor as follow:
onynxni PPPP φφφφ1111
−+=
The value of φPn obtained in this way should not exceed0.80φPno for tied columns and 0.85φPno for spirally reinforced columns. In the design problems, the trial size and reinforcement of the column is selected which is then checked to see if Pu ≤ φPn.
![Page 51: M.sc rc-11](https://reader038.fdocuments.net/reader038/viewer/2022103118/55c46298bb61eb514e8b474c/html5/thumbnails/51.jpg)