In order to promote public education and public safety, equal justice for all, a better informed citizenry, the rule of law, world trade and world peace, this legal document is hereby made available on a noncommercial basis, as it is the right of all humans to know and speak the laws that govern them.

Federation of Malysia≠ EDICT OF GOVERNMENT ±

MS 1118 (2008) (English): MALAYSIAN COCOA BUTTER- SPECIFICATION (FIRST REVISION)

MALAYSIAN STANDARD

MALAYSIAN COCOA BUTTER -SPECIFICATION (FIRST REVISION)

ICS: 67.140.30

Descriptors : cocoa butter, specification

© Copyright 2008

MS 1118:2008

DEPARTMENT OF STANDARDS MALAYSIA

MALAYSIAN STANDARD

MALAYSIAN COCOA BUTTER -SPECIFICATION (FIRST REVISION)

ICS : 67.140.30

Descriptors : cocoa butter, specification

© Copyright 2008

MS 1118:2008

DEPARTMENT OF STANDARDS MALAYSIA

DEVELOPMENT OF MALAYSIAN STANDARDS

The Department of Standards Malaysia (STANDARDS MALAYSIA) is the national

standards and accreditation body of Malaysia.

The main function of STANDARDS MALAYSIA is to foster and promote standards,

standardisation and accreditation as a means of advancing the national economy,

promoting industrial efficiency and development, benefiting the health and safety of

the public, protecting the consumers, facil itating domestic and international trade and

furthering international cooperation in relation to standards and standardisation.

Malaysian Standards (MS) are developed through consensus by committees which

comprise balanced representation of producers, users, consumers and others with

relevant interests, as may be appropriate to the subject at hand. To the greatest

extent possible, Malaysian Standards are aligned to or are adoption of international

standards. Approva l of a standard as a Malays ian Standard is governed by the

Standards of Malaysia Act 1996 [Act 549]. Malaysian Standards are reviewed

periodically. The use of Malaysian Standards is voluntary except in so far as they are

made mandatory by regulatory authorities by means of regu lations, local by-laws or

any other similar ways.

STANDARDS MALAYSIA has appointed SIRIM Berhad as the agent to develop,

distribute and sell the Malaysian Standards.

For further information on Malaysian Standards, please contact:

Department of Standards Malaysia OR Ministry of Science, Technology and Innovation Level 1 & 2, Block 2300, Century Square Jalan Usahawan 63000 Cyberjaya Selangor Darul Ehsan MALAYSIA

Tel: 603 8318 0002 Fax: 60 3 8319 3131 http://www.standardsmalaysia.gov.my

E-mail : central@standardsmalaysia.gov.my

SIRIM Berhad (Company No. 367474 - V) 1, Persiaran Data' Menteri Section 2 40000 Shah Alam Selangor Darul Ehsan MALAYSIA

Tel: 60355446000 Fax: 60 3 5510 8095 http://www.sirim.my

E-mail : msonline@sirim.my

DEVELOPMENT OF MALAYSIAN STANDARDS

The Department of Standards Malaysia (STANDARDS MALAYSIA) is the national

standards and accreditation body of Malaysia.

The main function of STANDARDS MALAYSIA is to foster and promote standards,

standardisation and accreditation as a means of advancing the national economy,

promoting industrial efficiency and development, benefiting the health and safety of

the public, protecting the consumers, facilitating domestic and international trade and

furthering international cooperation in relation to standards and standardisation .

Malaysian Standards (MS) are developed through consensus by committees which

comprise balanced representation of producers, users, consumers and others with

relevant interests, as may be appropriate to the subject at hand. To the greatest

extent possible , Malaysian Standards are aligned to or are adoption of international

standards. Approval of a standard as a Malaysian Standard is governed by the

Standards of Malaysia Act 1996 [Act 549] . Malaysian Standards are reviewed

periodically. The use of Malaysian Standards is voluntary except in so far as they are

made mandatory by regulatory authorities by means of regulations, locai by-laws or

any other similar ways.

STANDARDS MALAYSIA has appointed SIRIM Berhad as the agent to develop,

distribute and sell the Malaysian Standards.

For further information on Malaysian Standards, please contact:

Department of Standards Malaysia OR Ministry of Science, Technology and Innovation Level 1 & 2, Block 2300, Century Square Jalan Usahawan 63000 Cyberjaya Selangor Darul Ehsan MALAYSIA

Tel: 60383180002 Fax: 60 3 8319 3131 http://www.standardsmalaysia.gov.my

E-mail: central@standardsmalaysia.gov.my

SIRIM Berhad (Company No. 367474 - V) 1, Persiaran Dato' Menteri Section 2 40000 Shah Alam Selangor Darul Ehsan MALAYSIA

Tel : 60355446000 Fax: 60 3 55108095 http://www.sirim .my

E-mail : msonline@sirim .my

MS 1118:2008

CONTENTS

Committee representation ................................................................................... .

Foreword ....................................... '" ............................................ .

Page

. ii

. ..... iii

o Introduction...... ... ...... ... ......... ... ... ... ... ...... ... ... ... ...... ...... ... .. .....1

Scope .................................. ,. '" .... , ........ , ......... , ... '" .. , ........ ' ....................... 1

2 Normative references ......................................... , ........ , ........ " ... ... .. .1

Definition ........................................................................... .

Categories of Malaysian cocoa butter ......... '" ....... , ........ , ......... , .

Essential compositions and quality requirements ............................ .

Metal tolerance ........................................................................... .

Hygiene ................................................. , ................. , ........ , ......... '

Labelling ................... " ....... , ........ , ......... , ........ , ........ , ......................... .

~m~ .................................................................................. .

Legal requirements ................ , .......................................................... .

Analysis and test report .......... , ....... '" ................. , ................................ .

Sampling ..................................................................................... .

.1

... 2

.2

. .... 3

....... 3

..3

.4

...... 4

.4

. ... 4

3

4

5

6

7

8

9

10

11

12

13 Compliance .............. '" ......... '" ...... '" ....... , ........ , ........ , ......... , ........ , ........ , ..... 4

14 Certification mark .................................................... , ..................................... 4

Tables

Analytical characteristics of Malaysian cocoa butter .................... .

2 Metal tolerance for cocoa butter ................ ,. '" ....................... '

Annex A Guide to storage of cocoa butter ................................ .

© STANDARDS MALAYSIA 2008 - All rights reserved

. ..... .2

..... 3

. ..... 5

MS 1118:2008

CONTENTS

Page

Committee representation .......................................................................... , ............ ,., ............. , .. ii

Foreword ................................................ , ............. , ........................... '" .... . .... , iii

o

2

3

4

5

6

7

8

Introduction , ........ , .. , ................ , ........... , .............. , ................. .

Scope ..................................................................... , ............... .

Normative references ........................................................................... ..

Definition .......................................................................... ..

Categories of Malaysian cocoa butter. .................................................. ..

Essential compositions and quality requirements .................................... ..

Metal tolerance ................................................................................ .

.. 1

.. ... 1

.,2

.2

... 3

Hygiene...... ........................... ................. ... .................................. . .. ,3

Labelling ................................................................................................... 3

9 Storage ..................................... ., .............................................................. .4

10 Legal requirements .................... ... ............... ......... ............................ .4

11 Analysis and test report................... ......... .............. ........ ................. .4

12 Sampling ................................................................... ,........ ......... .......... ,4

13 Compliance ............................................................................................. 4

14 Certification mark .................. '" .. , ... " ......... , .. , .................. , ............................ .4

Tables

Analytical characteristics of Malaysian cocoa butter., .... , .. ,.. . ,. " ... ..,' .... .2

2 Metal tolerance for cocoa butter .............. , ....................... .. ....... "' .... ,.3

Annex A Guide to storage of cocoa butter ............ " .......... . ....... ...... , .......................... 5

© STANDARDS MALAYSIA 2008 All rights reserved

MS 1118:2008

Committee representation

The Industry Standards Committee on Food and Food Products (ISC U) under whose authority this Malaysian Standard was developed, comprises representatives from the following organisations:

Department of Agriculture, Malaysia Department of Standards Malaysia Federal Agricultural Marketing Authority Federation of Malaysian Manufacturers Malaysian Agricultural Research and Development Institute Malaysian Association of Standards Users Malaysian Institute of Food Technology Malaysian Palm Oil Association Malaysian Palm Oil Board Ministry of Agriculture and Agro-based Industry Ministry of Health Malaysia Ministry of Science and Technology (National Biotechnology Division) Universiti Kebangsaan Malaysia Universiti Putra Malaysia

The Technical Committee on Cocoa and Chocolate Products which developed this Malaysian Standard consists of representatives from the following organisations:

Barry Callebaut Malaysia Sdn Bhd

Cocoa House Industries Sdn Bhd

Department of Agriculture, Malaysia

Guan Chong Cocoa Manufacturer Sdn Bhd

JB Cocoa Sdn Bhd

Malaysian Agricultural Research and Development Institute

Malaysian Cocoa Board

Malaysian Palm Oil Board

Ministry of Health Malaysia

Universiti Kebangsaan Malaysia

Universiti Putra Malaysia

© STANDARDS MALAYSIA 2008 - All rights reserved

MS 1118:2008

Committee representation

The Industry Standards Committee on Food and Food Products (ISC U) under whose authority this Malaysian Standard was developed, comprises representatives from the following organisations:

Department of Agriculture, Malaysia Department of Standards Malaysia Federal Agricultural Marketing Authority Federation of Malaysian Manufacturers Malaysian Agricultural Research and Development Institute Malaysian Association of Standards Users Malaysian Institute of Food Technology Malaysian Palm Oil Association Malaysian Palm Oil Board Ministry of Agriculture and Agro-based Industry Ministry of Health Malaysia Ministry of Science and Technology (National Biotechnology Division) Universiti Kebangsaan Malaysia Universiti Putra Malaysia

The Technical Committee on Cocoa and Chocolate Products which developed this Malaysian Standard consists of representatives from the following organisations:

Barry Callebaut Malaysia Sdn Bhd

Cocoa House Industries Sdn Bhd

Department of Agriculture, Malaysia

Guan Chong Cocoa Manufacturer Sdn Bhd

JB Cocoa Sdn Bhd

Malaysian Agricultural Research and Development Institute

Malaysian Cocoa Board

Malaysian Palm Oil Board

Ministry of Health Malaysia

Universiti Kebangsaan Malaysia

Universiti Putra Malaysia

© STANDARDS MALAYSIA 2008 - All rights reserved

MS 1118:2008

FOREWORD

This Malaysian Standard was developed by Technical Committee on Cocoa and Chocolate Products under the authority of the Industry Standards Committee on Food and Food Products.

This Malaysian Standard is the first revision of MS 1118, Cocoa butter specification.

Major modifications in this revision are as follows:

a) the definition of cocoa butter has been updated;

b) the previous table 1 (solid fat content of Malaysian cocoa butter) has been removed as requested by industries;

c) the characteristics in previous table 2 ( Analytical characteristics of Malaysia cocoa butter) has omitted the data for categories, refractive index and blue value max as per current quality requirement;

d) the requirement for metal tolerance has been tabulated as table 3 ( Metal tolerance for Cocoa butter) and the requirements as per current regulation;

e) the labeling and hygiene requirements have been revised and amended according to current regulation;

f) exclusion of Appendix A (Definitions and essential composition of cocoa beans, cocoa nib, cocoa mass and cocoa press cake); and

g) Appendix B (Guide to storage of cocoa butter) has been renamed as Annex A (Guide to storage of cocoa butter).

This Malaysian Standard cancels and replaces MS 1118: 1988.

Compliance with a Malaysian Standard does not of itself confer immunity from legal obligations.

© STANDARDS MALAYSIA 2008 All rights reserved iii

MS 1118:2008

FOREWORD

This Malaysian Standard was developed by Technical Committee on Cocoa and Chocolate Products under the authority of the Industry Standards Committee on Food and Food Products.

This Malaysian Standard is the first revision of MS 1118, Cocoa butter specification.

Major modifications in this revision are as follows:

a) the definition of cocoa butter has been updated;

b) the previous table 1 (solid fat content of Malaysian cocoa butter) has been removed as requested by industries;

c) the characteristics in previous table 2 ( Analytical characteristics of Malaysia cocoa butter) has omitted the data for categories, refractive index and blue value max as per current quality requirement;

d) the requirement for metal tolerance has been tabulated as table 3 ( Metal tolerance for Cocoa butter) and the requirements as per current regulation;

e) the labeling and hygiene requirements have been revised and amended according to current regulation;

f) exclusion of Appendix A (Definitions and essential composition of cocoa beans, cocoa nib, cocoa mass and cocoa press cake); and

g) Appendix B (Guide to storage of cocoa butter) has been renamed as Annex A (Guide to storage of cocoa butter).

This Malaysian Standard cancels and replaces MS 1118: 1988.

Compliance with a Malaysian Standard does not of itself confer immunity from legal obligations.

© STANDARDS MALAYSIA 2008 All rights reserved iii

MS 1118:2008

MALAYSIAN COCOA BUTTER - SPECIFICATION (FIRST REVISION)

O. Introduction

This Malaysian Standard is the improvement of the specification in terms of quality of cocoa butter. With the existence of this standard, manufacturers can conform to a uniform standard of quality for cocoa butter use as ingredient in the manufacture of chocolates and chocolate related products.

1. Scope

This Malaysian Standard specifies the requirements for Malaysian cocoa butter.

2. Normative references

The following normative references are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated references, the latest editions of the normative references (including any amendments) apply.

MS 293, Specification for grading cocoa beans

MS 1119, Method of analysis for Malaysian cocoa butter and Malaysian cocoa powder

MS 1263, Method of sampling of Malaysian cocoa powder and Malaysian cocoa butter

MS 1376, Specification for cocoa mass

Malaysian Food Act 1983 and Food Regulations 1985

3. Definition

For the purpose of this Malaysian Standard, the following definitions apply;

Cocoa butter is the fat obtained from the following: Cocoa beans, cocoa nibs, and cocoa mass, (MS 293 and MS 1376) by mechanical or chemical process.

© STANDARDS MALAYSIA 2008 All rights reserved

MS 1118:2008

MALAYSIAN COCOA BUTTER - SPECIFICATION (FIRST REVISION)

O. Introduction

This Malaysian Standard is the improvement of the specification in terms of quality of cocoa butter. With the existence of this standard, manufacturers can conform to a uniform standard of quality for cocoa butter use as ingredient in the manufacture of chocolates and chocolate related products.

1. Scope

This Malaysian Standard specifies the requirements for Malaysian cocoa butter.

2. Normative references

The following normative references are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated references, the latest editions of the normative references (including any amendments) apply.

MS 293, Specification for grading cocoa beans

MS 1119, Method of analysis for Malaysian cocoa butter and Malaysian cocoa powder

MS 1263, Method of sampling of Malaysian cocoa powder and Malaysian cocoa butter

MS 1376, Specification for cocoa mass

Malaysian Food Act 1983 and Food Regulations 1985

3. Definition

For the purpose of this Malaysian Standard, the following definitions apply;

Cocoa butter is the fat obtained from the following: Cocoa beans, cocoa nibs, and cocoa mass, (MS 293 and IVIS 1376) by mechanical or chemical process.

© STANDARDS MALAYSIA 2008 -All rights reserved

MS 1118:2008

4. Categories of Malaysian cocoa butter

4.1 Cocoa butter may be produced and known as follows:

a) untreated;

b) deodorised;

c) degummed and deodorised; and

d) degummed, bleached and deodorised.

4.2 Pure Prime Pressed (PPP) or natural cocoa butter

It is the fat obtain as stated in 4.1 (a).

4.3 Degummed and deodorised PPP Cocoa Butter

It is the fat treated as stated in 4.1 (c).

4.4 Refined PPP Cocoa Butter

It is the fat treated as stated in 4.1 (d).

5. Essential compositions and quality requirements

5.1 The colour, odour and taste of all types of cocoa butter shall be characteristics of the designated product and shall be free from foreign odour and taste.

5.2 The analytical characteristics for Malaysian cocoa butter are shown in Table 1.

Table 1. Analytical characteristics for Malaysian cocoa butter

Melting polnt{Capiliary tube· tempered Free fatty Saponification value, Iodine value Unsaponifiable method) acid; % m/m oleic mg (Wij"s) matter (petroleum

acid, maximum KOHfg fat ether) %

Slip melting point Clear melting point mlm, maximum

31° to 34 "C 32" to 35"C 1.75 188t0198 32 to 38 0.6

2 © STANDARDS MALAYSIA 2008 - All rights reserved

MS 1118:2008

4. Categories of Malaysian cocoa butter

4.1 Cocoa butter may be produced and known as follows:

a) untreated;

b) deodorised;

c) degummed and deodorised; and

d) degummed, bleached and deodorised.

4.2 Pure Prime Pressed (PPP) or natural cocoa butter

It is the fat obtain as stated in 4.1 (a).

4.3 Degummed and deodorised PPP Cocoa Butter

It is the fat treated as stated in 4.1 (c).

4.4 Refined PPP Cocoa Butter

It is the fat treated as stated in 4.1 (d).

5. Essential compositions and quality requirements

5.1 The colour, odour and taste of all types of cocoa butter shall be characteristics of the designated product and shall be free from foreign odour and taste,

5.2 The analytical characteristics for Malaysian cocoa butter are shown in Table 1.

Table 1. Analytical characteristics for Malaysian cocoa butter

I Melting polntlCapiliary tube· tempered ' Free fatty Saponification value.! Iodine value U~'PO"'"~ i method) I acid; % mlm oleic mg iWij's) matter (petroleum

acid, maximum KOHlg fat ether)

I Slip melting point I I % I

Clear melting point

I mlm, maximum

J 31" 10 34 "C

i

32" to 35"C 1.75 J 188 to 198 32 to 38 0.6

I

2 © STANDARDS MALAYSIA 2008 All rights reserved

MS 1118:2008

6. Metal tolerance

The requirements for metal tolerances are described in Table 2.

Table 2. Metal tolerance for cocoa butter

Metal Maximum level (ppm) Arsenic (As) 0.5

Lead (Pb) 0.5 Mercury(Hg) 0.05

7. Hygiene

7.1 The hygienic practices shall comply with all the relevant statutory requirements or regulations relative to food processing, packaging, handling and hygiene currently enforced in Malaysia (Malaysian Food Act 1983 and Food Regulations 1985).

7.2 As much as possible in accordance to the good manufacturing practice, the products shall be free from objectionable matter.

7.3 When tested by appropriate methods of sampling and examination, the products shall not contain any substances originating from microorganisms in amount, which may represent hazard to health; and ensure the products are free of pathogenic microorganisms.

8. labelling

8.1 Each container shall be marked legibly and indelibly or a label shall be attached to the container, with the following information:

a) name of the product;

b) name and address of the manufacturer;

c) minimum net weight;

d) code number or marking device indicating month and year of manufacture; and

e) in the case of food produced, prepared or packaged in Malaysia, it shall be in Bahasa Malaysia and may include translation in other languages.

8.2 Net content

The net content shall be declared by weight in the metric or any other system of measurement.

© STANDARDS MALAYSIA 2008 - All rights reserved 3

MS 1118:2008

6. Metal tolerance

The requirements for metal tolerances are described in Table 2.

Table 2. Metal tolerance for cocoa butter

7. Hygiene

7.1 The hygienic practices shall comply with all the relevant statutory requirements or regulations relative to food processing, packaging, handling and hygiene currently enforced in Malaysia (Malaysian Food Act 1983 and Food Regulations 1985).

7.2 As much as possible in accordance to the good manufacturing practice, the products shall be free from objectionable matter.

7.3 When tested by appropriate methods of sampling and examination, the products shall not contain any substances originating from microorganisms in amount, which may represent hazard to health; and ensure the products are free of pathogenic microorganisms.

8. Labelling

8.1 Each container shall be marked legibly and indelibly or a label shall be attached to the container, with the following information:

a) name of the product;

b) name and address of the manufacturer;

c) minimum net weight;

d) code number or marking device indicating month and year of manufacture; and

e) in the case of food produced, prepared or packaged in Malaysia, it shall be in Bahasa Malaysia and may include translation in other languages.

8.2 Net content

The net content shall be declared by weight in the metric or any other system of measurement.

© STANDARDS MALAYSIA 2008 - All rights reserved 3

MS 1118:2008

8.3 Bulk packs

The information required by 8.1 and 8.2 shall either be given on the container or be given in accompanying documents except that the name of the product and the name and address of the manufacturer or packer shall appear on the container. However, the name and address of the manufacturer or packer may be replaced by an identification mark provided that such a mark is clearly identifiable with the accompanying document.

9. Storage

Recommendations relating to storage are given as a guide in Annex A.

10. Legal requirements

The product shall in all other aspects comply with the requirements of the legislations currently enforced in Malaysia.

11. Analysis and test report

This activity shall be carried out in accordance with the procedure laid down in MS 1119.

12. Sampling

Representative samples of the product shall be drawn as prescribed in MS 1263: 1992, 'Method of sampling for Malaysian cocoa powder and Malaysian cocoa butter.

13. Compliance

Upon testing, when each of the samples is found to conform to the requirements specified in the standard, the lot, batch or consignment from which the samples have been drawn shall be deemed to comply with this standard.

14. Certification mark

Each product, may by arrangement with a recognised certification body, be marked with the certification mark of that body, provided the product conforms to the requirements of this Malaysian Standard.

4 © STANDARDS MALAYSIA 2008 - All rights reserved

MS 1118:2008

8.3 Bulk packs

The information required by 8.1 and 8.2 shall either be given on the container or be given in accompanying documents except that the name of the product and the name and address of the manufacturer or packer shall appear on the container. However, the name and address of the manufacturer or packer may be replaced by an identification mark provided that such a mark is clearly identifiable with the accompanying document

9. Storage

Recommendations relating to storage are given as a guide in Annex A.

10. Legal requirements

The product shall in all other aspects comply with the requirements of the legislations currently enforced in Malaysia.

11. Analysis and test report

This activity shall be carried out in accordance with the procedure laid down in MS 1119.

12. Sampling

Representative samples of the product shall be drawn as prescribed in MS 1263: 1992, 'Method of sampling for Malaysian cocoa powder and Malaysian cocoa butter.

13. Compliance

Upon testing, when each of the samples is found to conform to the requirements specified in the standard, the lot, batch or consignment from which the samples have been drawn shall be deemed to comply with this standard.

14. Certification mark

Each product, may by arrangement with a recognised certification body, be marked with the certification mark of that body, provided the product conforms to the requirements of this Malaysian Standard.

4 © STANDARDS MALAYSIA 2008 -All rights reserved

Annex A (informative)

Guide to storage of cocoa butter

A 1. The optimal conditions for storage are as follows;

a) a low relative humidity of the surrounding air, if possible under 65 %;

MS 1118:2008

b) a temperature not exceeding 25°C, fluctuations in temperature should be avoided;

c) clean, well lit rooms, free of insects, rodents and other vermin;

d) absence of strong smelling foreign odours; and

e) stack at an adequate distance from both walls and floor.

© STANDARDS MALAYSIA 2008 - All rights reserveti 5

Annex A (informative)

Guide to storage of cocoa butter

A 1. The optimal conditions for storage are as follows;

a) a low relative humidity of the surrounding air, if possible under 65 %;

MS 1118:2008

b) a temperature not exceeding 25°C, fluctuations in temperature should be avoided;

c) clean, well lit rooms, free of insects, rodents and other vermin;

d) absence of strong smelling foreign odours; and

e) stack at an adequate distance from both walls and floor.

© STANDARDS MALAYSIA 2008 All rights reservetl 5

Acknowledgements

Members of Technical Committee on Cocoa and Chocolate Products

Mr Jumali Suratman (Chairman) Ms Irma Munirah Alias (Secretary) Ms Agnes Chen Ms Chang Pik Yeen Mr Mohamad Idrus Ab. Hamid Mr Pow Chun Chung Ms Saw Poh Chin Ms Sharifah Samsiah Mohamad

Mr Omar Tompang/ Dr Sabariah Samsudin Ms Salmi Yati Shamsudin Ms Shazlina Mohd Zaini Dr Nazaruddin Ramli Prof Dr Jinap Selamat

Malaysian Cocoa Board SIRIM Berhad Barry Callebaut Malaysia Sdn Bhd CocoaHouse Industries Sdn Bhd Department of Agriculture, Malaysia Guan Chong Cocoa Manufacturer Sdn Bhd JB Cocoa Sdn Bhd Malaysian Agricultural Research and Development Institute Malaysian Cocoa Board

Malaysian Palm Oil Board Ministry of Health Malaysia Universiti Kebangsaan Malaysia Universiti Putra Malaysia

© STANDARDS MALAYSIA 2008 - All rights reserved

Acknowledgements

Members of Technical Committee on Cocoa and Chocolate Products

Mr Jumali Suratman (Chairman) Ms Irma Munirah Alias (Secretary) Ms Agnes Chen Ms Chang Pik Yeen Mr Mohamad Idrus Ab. Hamid Mr Pow Chun Chung Ms Saw Poh Chin Ms Sharifah Samsiah Mohamad

Mr Omar Tompangl Dr Sabariah Samsudin Ms Salmi Yati Shamsudin Ms Shazlina Mohd Zaini Dr Nazaruddin Ramli Prof Dr Jinap Selamat

Malaysian Cocoa Board SIRIM Berhad Barry Callebaut Malaysia Sdn Bhd CocoaHouse Industries Sdn Bhd Department of Agriculture, Malaysia Guan Chong Cocoa Manufacturer Sdn Bhd JB Cocoa Sdn Bhd Malaysian Agricultural Research and Development Institute Malaysian Cocoa Board

Malaysian Palm Oil Board Ministry of Health Malaysia Universiti Kebangsaan Malaysia Universiti Putra Malaysia

© STANDARDS MALAYSIA 2008 All rights reserved