Model Lenght Power Color Temp. Optics...
Transcript of Model Lenght Power Color Temp. Optics...
Ordering Information1 SN 100 H 24
Model Lenght Power Color Temp. Optics Voltage
SN 100 H 273040RGB
LL 24
*SN- Min order quantity 9pcs
*Max run from single feed 6m (23’)
SNAKE Specification Sheet
Luminairen Radius, min R 314mm
n Uplight effect
n UL STD 1598, wet location, IP67, walk-over rated 500kg (1000 lb)
n Remote power supply
n Tempered glass 2x8mm thick
n Stainless steel 304 construction
n Direct concrete pour ABS installation hous-ing
n Snap in installation with no exposed hard-ware
n Supplied with oil and water resistant 0.18mm (7’) feed cable standard
n IP67 plug and play connector
Size
n 124mm (4.88”), 33.6mm (1.32” ),
90mm H (3.54” )
Powern H - 2.3W 2700K - 4000K, 222 lm
n H - 2.3W RGB
Color Temperaturen 27 - 2700K
n 30 - 3000K
n 40 - 4000K
n RGB
n 2 Step MacAdam
n CRI: > 85
Opticsn LL - line of light
Voltage
n 24 - 24Vdc fixture voltage
Installation housing order code
n SN335
Cable options
Jumper Cable
n 102796 - L= 1m
Lead Cable
n 102233 - L= 1m
34.08mm(1.34”)
h 89.1mm(3.53”)
34.08mm (1.34”)
121.
36
mm
(4
.78
”)
Power SupplyOn/Off
103233 - OT60 24V P
103196 - OT130 24V P
103234 - OT250 24V P
Power Supply integrated controls
102345 - ELDOLED Linear 100S (DXM,DALI+PS)
103502 - OT 210/220-240 /1-4CH - DALI
103507 - OT250/220...240/ 24V DIM P (1-10V)
International: +385 52 255 324 filixlighting.com [email protected]/GmbH: [email protected] MENA: [email protected] North America: filixlighting.com [email protected] Filix reserves the right to make technical changes without notice. 1
Click here for voltage drop and distances.
Applicationn Architectural and landscape lighting
n Curved uplight applications
n Linear marker light
n Gravel, soil or concrete
n UL STD 1598, IP67, Wet location
SNAKE Dimensions
Fixtu
reD
imm
ensio
ns
314mm
(12.36”)
Installatio
n
Min. possible circle
80.00mm (3.15”)
90mm(3.54”)
34.1mm(1.34”)
Housing
Drainage
Concrete
Drainage pipe or drainage layer
146 mm(5.75”)
115 mm(4.53”)
17 mm(0.67”)
80mm(3.15”)
90mm(3.54”)
34.08mm (1.34”)
International: +385 52 255 324 filixlighting.com [email protected]/GmbH: [email protected] MENA: [email protected] North America: filixlighting.com [email protected] Filix reserves the right to make technical changes without notice. 2
Wirin
g d
iagram
s
Qty. Part Number Description CaseNominal Input
Voltage (V)Nominal Input
Current (A)Power Factor
Output Power Range (W)
Location Rating
Range
D2024120 20W 24Vdc 120V 1 120 0.38 0.5 0.9-20 Dry -20°C – +50°C
D7524UNV 75W 24V UNV 2 120 to 277 0.99 0.99 0.9-75 Damp -25°C – +60°C
D9624UNV 96W 24V UNV 2 120 to 2770.970.39
0.9 1-96 Damp -20°C – +40°C
Although it is possible to exceed the remote mounting distance, the installer and/or end user must take precautions to prevent and/or test the effects of EMI (electromagnetic interference).
Qty. Part Number Description CaseNominal Input
Voltage (V)Nominal Input
Current (A)Power Factor
Output Power Range (W)
Dimming Mode
Dimming Control
Dimming Range
Location Rating
D9624UNVD1 96W 24V UNV DIM 1 120 to 2770.970.39
0.9 1-96 PWM 0-10V DC 10 –100% Damp
D4024120D2K or D4024120D2M
Hi-Lume A Series LED LTE (case k or m)
2/3 120 - - 5-40 PWMForward phase
with neutral1 –100% Dry
D4024UNVD3K or D4024UNVD3M
Hi-Lume A Series LED L3D (case k or m)
2/3 120 to 277 - - 5-40 PWM3-Wire or
Ecosystem® 1 –100% Dry
Although it is possible to exceed the remote mounting distance, the installer and/or end user must take precautions to prevent and/or test the effects of EMI (electromagnetic interference).
Non Dimming Drivers
Dimming Drivers
Case d
imen
sion
s
9.48" (241mm)
8.94" (227mm)
1.17" (30mm)
1.68" (43mm)
YELLOW
24V DC (+)
Return (-)
DIM Return (-)
Black (L)
White (N)VOLTAGE120-277 V AC50/60Hz Pout (max): 96 W
Vout: 24VDCIout: 0.04-4ADC
RED
Gray (-)
Purple (+)
0-10 V DC
InputBLUE
n.c.
2.36"(60.0mm)
2.20"(56mm)
2.20"(56mm)
2.36"(60mm)
24VDC+ –
LoadLoad side: use 30 to 14 AWG wire
Line side: use 20 to 12 AWG wire
Line
N L
1.20"(31mm)
Red(+)
Blue(-)
Black (L)
White (N)
VOLTAGE120-277 VAC50/60Hz
Input
24V DC Output
(+)
(-)
Black (L)
White (N)
VOLTAGE120 VAC50/60Hz
Input
24V DC Output
9.48" (241mm)
8.94" (227mm)
1.17" (30mm)
1.68" (43mm)
YELLOW
24V DC (+)
Return (-)
DIM Return (-)
Black (L)
White (N)VOLTAGE120-277 V AC50/60Hz Pout (max): 96 W
Vout: 24VDCIout: 0.04-4ADC
RED
Gray (-)
Purple (+)
0-10 V DC
InputBLUE
n.c.
2.36"(60.0mm)
2.20"(56mm)
2.20"(56mm)
2.36"(60mm)
24VDC+ –
LoadLoad side: use 30 to 14 AWG wire
Line side: use 20 to 12 AWG wire
Line
N L
1.20"(31mm)
Red(+)
Blue(-)
Black (L)
White (N)
VOLTAGE120-277 VAC50/60Hz
Input
24V DC Output
(+)
(-)
Black (L)
White (N)
VOLTAGE120 VAC50/60Hz
Input
24V DC Output
1. 20W 2. 75W + 96 W
Case d
imen
sion
s4.2"
(106.7mm)
1.0"(25.4mm)
3.0"(76.2mm)
4.9"(124.45mm)
4.6"(116.8mm)
1.18"(29.9mm)
0.98"(24.9mm)
14.13"(358.9mm)
13.78"(350.0mm)
9.48"(240.8mm)
8.94"(227.1mm) 1.17"
(29.7mm)
1.68"(42.7mm)
1. 96W 2. Hi-Lume (case K) 3. Hi-Lume (case M)
9.48"
8.94" 1.17"
1.68"
Black (L)
Power SupplyWhite (N)
2.36"
2.20"
2.20"
2.36"
24VDC+ –
LoadLoad side: use 30 to 14 AWG wire
Line side: use 20 to 12 AWG wire
Line
N L
1.20"
(+)
(-)
Wirin
g d
iagram
s
96W L3D (3-wire)LTE (forward phase with neutral) L3D (Ecosystem®)
20W, 75W, 96 WSuggested wiring size*
Load per driver≤48W ≤72W ≤96W
Wir
e ga
uge
#18AWG 37’ 25’ 18’
#16AWG 59’ 39’ 29’
#14AWG 95’ 63’ 47’
#12AWG 151’ 101’ 75’
#10AWG 241’ 160’ 120’* Voltage drop guide for 24VDC. Actual Voltage drop to be calculated by installer.
SQ100 Deco Power Supplies
410 381 1497 inter-lux.com [email protected] reserves the right to make technical changes without notice. # 930-3007 (ref 0) 3
Wiring Diagram for 3-Wire Control Wiring Diagram for EcoSystem® Digital Control
Dimmed Hot (Orange)
Switched Hot (Black)
Neutral (White)
Ground (Green) Ground
+V
-V
To 3
-wire
Dim
min
g C
ontr
ol
Hi-lume®A-Series
Switched Hot (Black)
Neutral (White)
Ground (Green)
E1 (Purple)
E2 (Purple)
LED lightengine
To E
coSy
stem
®D
igita
l Lin
kTo
Lin
eVo
ltag
e
Note: Colors shown correspond to terminal blocks on driver.
Ground
+V
-V
Hi-lume®A-Series
LED lightengine
Wiring Diagram for Forward Phase Control
Note: Colors shown correspond to terminal blocks on driver.
Dimmed Hot (Black)
Neutral (White)
Ground (Green)
To F
orw
ard
Phas
e C
ontr
ol
Ground
+V
-V
Hi-lume®A-Series
LED lightengine
Black (L)
Power Supply
White (N)
Purple (+)
Gray (-)
(+)
(-)
RGB Control Interface Details
Qty. Part Number DescriptionNominal Input
Voltage (V)Maximum Outputper channel (W)
Output Power Range (W)
Controls (By Others)
CORGBSEQ OT RGB Sequencer 24 48 96 (1-3) 0-10V dimmer(s)
CORGBDMX OT DMX RGB 24 48 96 DMX controller
Although it is possible to exceed the remote mounting distance, the installer and/or end user must take precautions to prevent and/or test the effects of EMI (electromagnetic interference).
0.79"(20.0mm)
1.65" (41.9mm)
0.14"(3.6mm)
6.77"(172.0mm)
6.77"(172.0mm)
OT RGB SEQUENCER
LED Modules
24VDC
RGB
+++
+
+ Speed+ Dim+ Prog.
1-10V;
<0.6mA
(1-3) 0-10V DIMMERS (by others)
OT DMX RGB
LED Modules
10 - 24VDC
RGB
+
+
+
DMX Controller (by others)
GRD Data Data+
+
DMX-Control Address
1
2
3
RGB Control Interface case dimensions (Sequencer and DMX) Maximum wiring distance*
Load per color
≤48W
Wir
e ga
uge
#18AWG 37’
#16AWG 59’
#14AWG 95’
#12AWG 151’
#10AWG 241’* Voltage drop guide for 24VDC. Actual Voltage drop to be calculated by installer.
OT RGB Sequencer
RGB Fixture 1
DMX Controller (by others)
Power Supply
(+)
R
G
B
RGB Fixture 2
RGB Fixture 1
(+)
R
G
B
RGB Fixture 2
OT DMX RGB
Power Supply
OT RGB Sequencer
RGB Fixture 1
DMX Controller (by others)
Power Supply
(+)
R
G
B
RGB Fixture 2
RGB Fixture 1
(+)
R
G
B
RGB Fixture 2
OT DMX RGB
Power Supply
OT RGB Sequencer
RGB color changing and dimming interface controlled by (3) 0-10v dimmers.First dimmer controls speed of color change.Second dimmer dims the 3 outputs (RGB) together.
Third dimmer selects one of the 8 pre-programmed color sequences.All 3 dimmers are required for full functionality or 1 or 2Can be used for specific functionality
See installation / driver instructions for details. Must order power supply separately
OT DMX RGB
DMX-controllable addressable interface. Address is assigned with 3 rotary channel selectors. Selection is made only for the first of the three channels desired.
The assigned address will control a set of three consecutive addresses. For example, if address #1 is selected, #1 controls the red leds output, #2 controls the blue leds output and #3 controls the green leds output.
See installation / driver instructions for details. Must order power supply separately
SQ100 Deco RGB Interface
410 381 1497 inter-lux.com [email protected] reserves the right to make technical changes without notice. # 930-3007 (ref 0) 4