Mobil 2004 Brief Product Book

M�bil BriefProductDescriptions2004 Edition

3225 GALLOWS ROAD, FAIRFAX, VIRGINIA 22037-0001For more information, call 1-800-662-4525 or visit us at www.mobil.com©Exxon Mobil Corporation 1975, 1977, 1978, 1979, 1981, 1984, 1986, 1989, 1993, 1994, 1995, 1998, 2001, 2002, 2003Due to continual product research and development, the information contained herein is subject to change without notification.

Mobil Product Book.qxd 6/25/04 4:09 PM chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide

Please Recycle

The pages in thisbook are Recyclable

Mobil Product Book.qxd 6/25/04 4:09 PM chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide

TABLE OF CONTENTS

i

INTRODUCTION .......................................................................................................................... iii

ALPHABETICAL INDEX OF MOBIL PRODUCTS...................................................................... v–vii

APPLICATION INDEX OF MOBIL PRODUCTS ......................................................................... viii–xiii

BRIEF DESCRIPTIONS/TYPICAL CHARACTERISTICS OFMOBIL LUBRICANTS ................................................................................................................. 1–41

HEALTH AND SAFETY PRECAUTIONS.................................................................................... 43–45

MATERIAL SAFETY DATA SHEETS (MSDS) ........................................................................... 46

APPENDICES .............................................................................................................................. 47–57Additives for Premium Lubricating Oils................................................................................... 47SAE Viscosity Grades for Engine Oils .................................................................................... 48SAE J306 Viscosity Grades For Gear Oils ............................................................................. 48ISO Viscosity Classification System ....................................................................................... 49Grease Consistency Classification: NLGI Classification ........................................................ 50Viscosity Conversion Table .................................................................................................... 50Conversion: API to Specific Gravities..................................................................................... 50Commercial Engine Oils Chart ............................................................................................... 51Gasoline Engine Oil Application Chart ................................................................................... 52ANSI-AGMA Industrial Gear Lubricants 9005-D94 ................................................................ 53Natural Gas Engine Oil Recommendations............................................................................ 54Viscosity Classification Equivalents........................................................................................ 55Understanding Oil Analysis .................................................................................................... 56Yardmark Interpretation Key................................................................................................... 57

Mobil Product Book.qxd 6/25/04 4:09 PM Page i chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide

ii

QUESTIONS?CALL THE MOBIL TECHNICAL SUPPORT CENTER

AT

1 (800) 662-4525

OR VISIT OUR WEBSITE ATwww.mobil.com

Mobil Product Book.qxd 6/25/04 4:09 PM Page ii chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide

INTRODUCTION

iii

Mobil branded lubricants are backed by our uncompromising commitment to

Mobil lubricants are developed to typically exceed original equipment manufacturer (OEM) andindustry requirements. Leading edge technology and close OEM involvement enable ExxonMobilscientists to formulate Mobil oils and greases that help achieve peak machine performance.

Mobil products are supported by innovative programs and technical expertise to reduce the totalcost of lubrication. Ask your ExxonMobil field engineer how he or she can help you reduceexpenditures, improve revenues, and/or improve your process and asset management.

The 2004 edition of the MOBIL BRIEF PRODUCT DESCRIPTIONS book describes theextensive line of industrial, commercial vehicle, passenger vehicle and marine and aviationlubricants offered by ExxonMobil. This book consists of four sections:

• Product Indices

- Alphabetical Index of Mobil Products—Product family names are listed alphabeticallywith their respective page numbers. Products registered with the US Patent andTrademark Office are designated by the ® on the shoulder of the mark, for example:Mobil DTE® 20 Series.

DEXRON® and MERCON® are registered trademarks of the General Motors and FordMotor Company, respectively.

- Application Index of Mobil Products—Applications are listed alphabetically with the pagenumber of the respective product family(s).

• Lubricant information

- Brief Descriptions/Typical Characteristics of Mobil Products—Product families are listedalphabetically. The physical properties shown are characteristic of typical productionbatches. They are not manufacturing specifications. All are subject to change.

• Health and Safety Precautions—Many petroleum products pose potential human health,safety, and environmental hazards. We strongly urge you to read these general precautionsthoroughly and obtain the appropriate Material Safety Data Sheets.

• Appendices—These tables and notes contain a variety of useful information such asconversion charts, application charts, a section on Understanding Oil Analysis, YardmarkInterpretation Key, and other recommendations.

For additional information about Mobil products, refer to specific product data sheets. They maybe obtained on the web at www.mobil.com or by calling the Mobil Technical Support Center at1-800-662-4525 or from your local ExxonMobil representative.

For general information, visit our website at www.mobil.com.

If this publication is more than two years old, please contact us to ensure that it is thelatest issue.

■ Performance ■ Innovation ■ Expertise

Mobil Product Book.qxd 6/25/04 4:09 PM Page iii chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guid

iv


AT

1 (800) 662-4525


Mobil Product Book.qxd 6/25/04 4:09 PM Page iv chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide

ALPHABETICAL INDEX OF MOBIL PRODUCTS

v

MOBIL PRODUCT PAGE

Curve Grease 213.............................................................................................................. 1Gargoyle Arctic® Oils .......................................................................................................... 1Gargoyle Arctic SHC® 200 Series ...................................................................................... 1Gear Lube 375 NC Spray Can........................................................................................... 34Mobil 1® Motorcycle Oils..................................................................................................... 2Mobil 1 with SuperSyn™.................................................................................................... 2Mobil 1 Synthetic ATF........................................................................................................ 2Mobil 1 Synthetic Gear Lubricant ....................................................................................... 3Mobil 1 Synthetic Grease................................................................................................... 3Mobil 1 Synthetic Spray Lubricant ..................................................................................... 3Mobil Aero® HF................................................................................................................... 3Mobil Aero HFA.................................................................................................................. 4Mobil Almo® 500 Series...................................................................................................... 4Mobil Arctic Turbine® 150 ................................................................................................... 4Mobil ATF 210.................................................................................................................... 4Mobil Aviation Grease SHC 100 ........................................................................................ 4Mobil Centaur Moly 1 & 2................................................................................................... 5Mobil Cylinder Oils ............................................................................................................. 5Mobil Delvac 1® .................................................................................................................. 5Mobil Delvac® 1300 Super.................................................................................................. 6Mobil Delvac 1600 Series .................................................................................................. 6Mobil Delvac Hydraulic 10W .............................................................................................. 6Mobil Delvac Xtreme Service Grease ............................................................................... 6Mobil Drive Clean Plus....................................................................................................... 7Mobil Drive Clean Oil HD 30 .............................................................................................. 7Mobil Drive Clean Oils™.................................................................................................... 7Mobil DTE® 10M Series...................................................................................................... 8Mobil DTE 20 Series .......................................................................................................... 8Mobil DTE 724 Oil .............................................................................................................. 8Mobil DTE 790 Oil Series .................................................................................................. 8Mobil DTE 800 Series ........................................................................................................ 9Mobil DTE Excel Series ..................................................................................................... 9Mobil DTE FM 32 ............................................................................................................... 9Mobil DTE Oil 105.............................................................................................................. 9Mobil DTE Oil Named Series ............................................................................................. 10Mobil DTE PM Series......................................................................................................... 10Mobil EAL® 224H................................................................................................................ 10Mobil EAL Arctic Series ..................................................................................................... 11Mobil EAL Envirosyn® H Series.......................................................................................... 11Mobil Glygoyle® 22 and 30 ................................................................................................. 11Mobil Glygoyle® HE Series ................................................................................................. 12Mobil Infinitec 152 ............................................................................................................. 12Mobil Hydraulic Oil AW Series ........................................................................................... 12Mobil Jet Oil II .................................................................................................................... 13Mobil® Jet Oil 254 ............................................................................................................... 13Mobil Mist Lube Series....................................................................................................... 13Mobil® Multi-Purpose ATF .................................................................................................. 14Mobil Pegasus 1® ............................................................................................................... 14Mobil Pegasus® 505 (formerly Mobil Pegasus 485) ........................................................... 15

Mobil Product Book.qxd 6/25/04 4:09 PM Page v chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide

ALPHABETICAL INDEX OF MOBIL PRODUCTS(continued)

vi

MOBIL PRODUCT PAGE

Mobil Pegasus 505-SAE 30 (formerly Mobil Pegasus 385) ............................................... 15Mobil Pegasus 605 (formerly Mobil Pegasus 426) ............................................................ 15Mobil Pegasus 610 (formerly Mobil Pegasus 446) ............................................................ 15Mobil Pegasus 701 (formerly Mobil Pegasus 490) ............................................................ 15Mobil Pegasus 701-SAE 30 (formerly Mobil Pegasus 390) ............................................... 15Mobil Pegasus 710 (formerly Mobil Pegasus 89) .............................................................. 16Mobil Pegasus 801 (formerly Mobil Pegasus 100/40) ....................................................... 16Mobil Pegasus 801-SAE 30 (formerly Mobil Pegasus 100/30) .......................................... 16Mobil Pegasus 805 Series ................................................................................................. 16Mobil Pegasus 905 ............................................................................................................ 17Mobil Pegasus Special 15W-40 ......................................................................................... 17Mobil Polyrex EM ............................................................................................................... 17Mobil Polyrex EP2.............................................................................................................. 17Mobil Polyrex® 372 ............................................................................................................. 17Mobil Pyrogard® 53............................................................................................................. 17Mobil Pyrogard D ............................................................................................................... 18Mobil Rarus® 427................................................................................................................ 18Mobil Rarus 800 Series...................................................................................................... 18Mobil Rarus SHC® 1020 Series.......................................................................................... 19Mobil SHC® 500 Series ...................................................................................................... 19Mobil SHC 600 Series........................................................................................................ 19Mobil SHC 800 Series........................................................................................................ 20Mobil SHC PM Series ........................................................................................................ 20Mobil Synthetic Oven Lube 1090 ....................................................................................... 20Mobil Synturion® 6 .............................................................................................................. 20Mobil Vactra® Oil Named Series......................................................................................... 21Mobil Vactra Oil Numbered Series..................................................................................... 21Mobil Vacuoline® 100 Series .............................................................................................. 21Mobil Vacuoline 500 Series ............................................................................................... 22Mobil Vacuoline Oil 1400 Series ........................................................................................ 22Mobil Vacuum® Pump Oil ................................................................................................... 22Mobil Vaprotec® Light ......................................................................................................... 22Mobil Velocite® Oil Series................................................................................................... 23Mobilarma® 200 Series....................................................................................................... 23Mobilarma 500 Series ........................................................................................................ 23Mobilarma 777 and 778 ..................................................................................................... 23Mobilarma 798 ................................................................................................................... 24Mobilfluid® 350.................................................................................................................... 24Mobilfluid 424, LT............................................................................................................... 24Mobilgard® 1 SHC .............................................................................................................. 24Mobilgard M50 ................................................................................................................... 25Mobilgard 300 .................................................................................................................... 25Mobilgard 312, 412, 512 .................................................................................................... 25Mobilgard M30, M40 .......................................................................................................... 25Mobilgard 450 NC .............................................................................................................. 26Mobilgard 570 .................................................................................................................... 26Mobilgard ADL Series ........................................................................................................ 26Mobilgear® 600 Series........................................................................................................ 27Mobilgear SHC® 150, 220, 320, 460, and 680 ................................................................... 27

Mobil Product Book.qxd 6/25/04 4:09 PM Page vi chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide

ALPHABETICAL INDEX OF MOBIL PRODUCTS(continued)

vii

MOBIL PRODUCT PAGE

Mobilgear SHC 1000, 1500, 3200, and 6800..................................................................... 27Mobilgear SHC 22M, 46M.................................................................................................. 27Mobilgear SHC XMP 320................................................................................................... 28Mobilgrease® 28 ................................................................................................................. 28Mobilgrease CM-L, CM-P, CM-S, CM-W ........................................................................... 28Mobilgrease EAL 100 Series ............................................................................................. 29Mobilgrease FM Series ...................................................................................................... 29Mobilgrease HT Series ...................................................................................................... 29Mobilgrease Moly 50, 51, 52, 50 Arctic .............................................................................. 30Mobilgrease XHP 222 and XHP 222 Special ..................................................................... 30Mobilgrease XTC ............................................................................................................... 30Mobilith® AW Series ........................................................................................................... 31Mobilith SHC® 100.............................................................................................................. 31Mobilith SHC 220, 221, 460, 007 and 1500 ....................................................................... 31Mobilith SHC PM Series .................................................................................................... 32Mobilmet® Alpha, Sigma, Gamma, Omega ........................................................................ 32Mobilmet Aqua Rho ........................................................................................................... 32Mobilmet CCF Series......................................................................................................... 32Mobilmet Upsilon, Omicron, Omicron HD, Nu ................................................................... 33Mobilmet 100 Series .......................................................................................................... 33Mobilmet TC 30.................................................................................................................. 33Mobiltac® 325 NC and 375 NC........................................................................................... 34Mobiltac LL, MM, QQ ......................................................................................................... 34Mobiltemp 2 ....................................................................................................................... 34Mobiltemp® 78 .................................................................................................................... 34Mobiltemp SHC® 32............................................................................................................ 34Mobiltherm® 603, 605 ......................................................................................................... 35Mobiltrans AST .................................................................................................................. 35Mobiltrans® HD................................................................................................................... 35Mobiltrans SHC 50............................................................................................................. 36Mobiltrans SHC Arctic ........................................................................................................ 36Mobilube HD 80W-140....................................................................................................... 36Mobilube HD® LS 80W-90 .................................................................................................. 37Mobilube HD Plus .............................................................................................................. 37Mobilube SHC®................................................................................................................... 37Mobilube® XFD................................................................................................................... 38Mobilux EP 023.................................................................................................................. 38Mobilux EP 111.................................................................................................................. 38Mobilux EP Arctic®.............................................................................................................. 39Mobilux® EP Series ............................................................................................................ 39Nyvac® FR 200D Fluid........................................................................................................ 39Quaker Quintolubric® 822 Series........................................................................................ 39Quaker Quintolubric 822-EHC ........................................................................................... 40Socony® Oven Conveyor Lubricant .................................................................................... 40Thermrex® Series Oils ........................................................................................................ 40Vacmul® A6 and 2105 ........................................................................................................ 40Vacmul 280 and 281 .......................................................................................................... 41Vacmul 3 A, 3 D, 03D, 30 A 20 .......................................................................................... 41Vacsul 18F ......................................................................................................................... 41Whiterex® 425..................................................................................................................... 41

Mobil Product Book.qxd 6/25/04 4:09 PM Page vii chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guid

APPLICATION INDEX OF MOBIL PRODUCTS

viii

GREASE APPLICATIONS MOBIL LUBRICANT PAGE

Agriculture Equipment Mobil Delvac Xtreme Service Grease ............................6Mobilgrease CM-L, CM-P, CM-S, CM-W......................28Mobilgrease XHP 222 and XHP 222 Special ...............30

Automotive Mobil 1 Synthetic Grease ...............................................3Mobil Infinitec 152 ........................................................12

Aviation Mobil Aviation Grease SHC 100.....................................5Mobilgrease 28 ............................................................28

Bearings General Purpose Mobil Polyrex EP2 ........................................................17Mobilgrease XHP 222 ..................................................30Mobilith AW Series .......................................................31Mobilith SHC 220, 221, 460, 007 and 1500 .................31Mobilux EP Series ........................................................39

Couplings Mobilgrease XTC..........................................................30Mobilux EP 111 ............................................................38

Electric Motor Bearings Mobil Polyrex EM ........................................................17Mobilith SHC 100 .........................................................31Mobilith AW Series .......................................................31

Environmentally Sensitive Mobilgrease EAL 100 Series........................................29Applications

Food Processing Mobilgrease FM Series ................................................29Machinery

Gears Mobilith SHC 007 .........................................................31Mobilux EP 023 ............................................................38

High Temperature Applications Mobil Polyrex 372.........................................................17Mobil Polyrex EM .........................................................17Mobil Polyrex EP2 ........................................................17Mobilith SHC 220, 221, 460, 007 and 1500 .................31Mobilgrease 28.............................................................28Mobiltemp 78................................................................34Mobiltemp SHC 32 .......................................................34

Low Temperature Applications Mobilgrease Moly 50 Arctic ..........................................30Mobilith SHC 220, 221, 460, 007 and 1500 .................31Mobiltemp SHC 32 .......................................................34Mobilux EP Arctic .........................................................39

Off-Highway Heavy-Duty Centaur Moly 1 & 2.........................................................5Equipment

Mobil Product Book.qxd 6/25/04 4:09 PM Page viii chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Gui

APPLICATION INDEX OF MOBIL PRODUCTS(continued)

ix

GREASE APPLICATIONS MOBIL LUBRICANT PAGE

Off-Highway Heavy-Duty Mobilgrease CM-L, CM-P, CM-S, CM-W......................28Equipment Mobilgrease Moly 50, 51, 52, 50 Arctic ........................30

Mobilgrease XHP 222 and XHP 222 Special ...............30

Paper Machines Mobilith SHC PM Series...............................................32Mobilith AW Series .......................................................31

Railroad Greases Curve Grease 213 ..........................................................1Mobilith SHC 221 .........................................................31

Steel Mills Centaur Moly 1 & 2.........................................................5Mobil Polyrex 372.........................................................17Mobil Polyrex EP2 ........................................................17Mobilgrease HT Series.................................................29

Trucking Centaur Moly 1 & 2.........................................................5Mobil Delvac Xtreme Service Grease ............................6Mobilgrease HT Series.................................................29Mobilgrease XHP 222 and XHP 222 Special ...............30Mobilith SHC 220, 460, 007 .........................................31

OIL APPLICATIONS

Barrier Fluid Mobil Synturion 6..........................................................20

Bearings Mobil Glygoyle 22 and 30.............................................11Mobil SHC 600 Series ..................................................19Mobil DTE Oil Named Series .......................................10Mobil Vactra Oil Named Series ....................................21

Compressors, Centrifugal Mobil SHC 600 Series ..................................................19Mobil DTE Oil Named Series .......................................10Mobil DTE 800 Series ....................................................9Mobil DTE 790 Oil Series ...............................................8Mobil Arctic Turbine 150.................................................4

Compressors, Reciprocating Mobil DTE Oil 105 ..........................................................9Mobil Rarus 427 ...........................................................18Mobil Rarus 800 Series ................................................18Mobil DTE Oil Named Series .......................................10

Compressors, Refrigeration Gargoyle Arctic Oils........................................................1Gargoyle Arctic SHC 200 Series ....................................1Mobil EAL Arctic Series................................................11

Compressors, Rotary Mobil Rarus 800 Series ................................................18Mobil Rarus SHC 1020 Series .....................................19Mobil DTE Oil Named Series .......................................10Mobil SHC 600 Series ..................................................19

Couplings Mobilgear 600 Series ...................................................27Mobilgear SHC 1000, 1500, 3200 and 6800 ................27

Mobil Product Book.qxd 6/25/04 4:09 PM Page ix chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide


x

OIL APPLICATIONS MOBIL LUBRICANT PAGE

Cutting Fluids Active Mobilmet Alpha.............................................................32Mobilmet Beta CCF ......................................................32Mobilmet Delta CCF .....................................................32Mobilmet Gamma .........................................................32Mobilmet Kappa CCF ...................................................32Mobilmet Lambda CCF ................................................32Mobilmet Omega ..........................................................32Mobilmet Sigma............................................................32Mobilmet TC 30 ............................................................33Mobilmet Theta CCF ....................................................32Vacmul A6 ....................................................................40Vacsul 18 F ..................................................................41

Cutting Fluids Non-Staining Mobilmet Nu .................................................................33Mobilmet Omicron ........................................................33Mobilmet Omicron HD ..................................................33Mobilmet Upsilon..........................................................33Vacmul 280 and 281 ....................................................41

Cutting Fluids Water Soluble Mobilmet Aqua Rho......................................................32Mobilmet 100 Series.....................................................33

Drive Train, Commercial Vehicle Mobilube HD 80W-140 .................................................36Mobilube HD LS 80W-90..............................................37Mobilube HD Plus.........................................................37Mobilube SHC ..............................................................37Mobilube XFD...............................................................38

EDM/Grinding/Honing Vacmul A6 and 2105 ....................................................40

Electric Motors Oiled Mobil DTE 790 Oil Series ...............................................8Mobil DTE Oil Named Series .......................................10Mobil SHC 600 Series ..................................................19

Engine Oils, Diesel Mobil Delvac 1................................................................5Mobil Delvac 1600 Series...............................................6Mobil Delvac 1300 Super ...............................................6

Engine Oils, Jet Mobil Jet Oil II...............................................................13Mobil Jet Oil 254...........................................................13

Mobil Product Book.qxd 6/25/04 4:09 PM Page x chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide


xi


Engine Oils, Marine Crosshead Mobilgard 300...............................................................25

Crosshead, Cylinder Mobilgard 570...............................................................26

Trunk Piston Mobilgard 312...............................................................25Mobilgard 412...............................................................25Mobilgard 512...............................................................25Mobilgard 330...............................................................25Mobilgard 430...............................................................25Mobilgard 340...............................................................26Mobilgard 440...............................................................26Mobilgard ADL Series ..................................................26Mobilgard 450 NC ........................................................26Mobilgard M50..............................................................25Mobilgard 1 SHC ..........................................................24

Engine Oils, Motorcycle Mobil 1 Motorcycle Oils ..................................................2

Engine Oils, Passenger Vehicle Mobil 1 with SuperSyn....................................................2Mobil Drive Clean Oils ....................................................7Mobil Drive Clean Oil HD 30 ..........................................7Mobil Drive Clean Plus ...................................................7

Gas Engines Ashless Pegasus 701-SAE 30 ...................................................15Pegasus 701 ................................................................15Pegasus 801-SAE 30 ...................................................16Pegasus 801 ................................................................16Pegasus Special 15W-40 .............................................17

Gas Engines Low Ash Pegasus 1 ....................................................................14Pegasus 505-SAE 30 ...................................................15Pegasus 505 ................................................................15Pegasus 805 ................................................................16Pegasus 805 Super......................................................16Pegasus 905 ................................................................17

Gas Engines Medium Ash Pegasus 710 ................................................................16

Gas Engines Landfill Pegasus 605 ................................................................15Pegasus 610 ................................................................15

Mobil Product Book.qxd 6/25/04 4:09 PM Page xi chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide

APPLICATION INDEX OF MOBIL PRODUCTS (continued)

xii


Gears, Enclosed Mobilgear 600 Series ...................................................27Mobilgear SHC 150, 220, 320, 460, and 680 ...............27Mobilgear SHC XMP 320 .............................................28Mobil Glygoyle HE Series.............................................12Mobil SHC 600 Series ..................................................19Mobil DTE Oil Named Series .......................................10Mobil Cylinder Oils .........................................................5

Gears, Open Mobilgear SHC 1000, 1500, 3200, and 6800 ...............27Mobiltac 325 NC and 375 NC.......................................34Mobiltac LL, MM, QQ ...................................................34Gear Lube 375 NC Spray Can .....................................34

Gear Oils, Passenger Vehicle Mobil 1 Synthetic Gear Lubricant ...................................3Mobilube HD 80W-140 .................................................36Mobilube HD Plus.........................................................37Mobilube SHC ..............................................................37

Heat Transfer Systems Mobiltherm 603 and 605...............................................35

Hydraulic Systems, Aviation Mobil Aero HF ................................................................3Mobil Aero HFA ..............................................................4

Hydraulics, All Season Mobil DTE 10M Series ...................................................8

Hydraulics, Anti-Wear Mobil SHC 500 Series ..................................................19Mobil DTE 20 Series ......................................................8Mobil Hydraulic Oil AW Series .....................................12

Hydraulics, Commercial Vehicle Mobiltrans HD...............................................................35Mobil Delvac Hydraulic 10W ..........................................6Mobil Delvac 1600 Series...............................................6Mobilfluid 424, LT .........................................................24Mobil DTE 10M Series ...................................................8Mobil Hydraulic Oil AW Series .....................................12

Hydraulics, Environmentally Aware Mobil EAL 224 H ..........................................................10Mobil EAL Envirosyn H Series .....................................11

Hydraulics, Fire-resistant Mobil Pyrogard 53 ........................................................17Mobil Pyrogard D..........................................................18Nyvac FR 200D Fluid ...................................................39Quaker Quintolubric 822/888 .......................................39Quaker Quintolubric 822-EHC......................................40

Mobil Product Book.qxd 6/25/04 4:09 PM Page xii chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guid


xiii


Hydraulics, Food Grade Mobil DTE FM 32 ...........................................................9

Hydraulics, Non-Zinc Mobil DTE Excel Series..................................................9

Hydraulics, R&O Mobil DTE Oil Named Series .......................................10Mobil Vactra Oil Named Series ....................................21

Pumps Mobil DTE Oil Named Series .......................................10Mobil SHC 600 Series ..................................................19Mobil SHC 500 Series ..................................................19Mobil DTE 790 Oil Series ...............................................8Mobil DTE 20 Series ......................................................8Mobil Hydraulic Oil AW Series .....................................12Mobil DTE 10M Series ...................................................8Mobil Vacuum Pump Oil ...............................................22

Rust Preventives Mobil Vaprotec Light.....................................................22Mobilarma 200 Series ..................................................23Mobilarma 500 Series ..................................................23Mobilarma 777 and 778................................................23Mobilarma 798..............................................................24

Transmission Fluids, Mobilfluid 424, LT .........................................................24Commercial Vehicle Mobiltrans AST.............................................................35

Mobiltrans HD...............................................................35Mobiltrans SHC 50 .......................................................36Mobiltrans SHC Arctic ..................................................36

Transmission Fluids, Mobil 1 Synthetic ATF ....................................................2Passenger Vehicle Mobil ATF 210 ................................................................4

Mobil Multi-Purpose ATF..............................................14

Turbines, Combine Cycle Mobil DTE 800 Series ....................................................9

Turbines, Gas Mobil DTE 724 Oil ..........................................................8Mobil SHC 800 Series ..................................................20Mobil Arctic Turbine 150.................................................4

Turbines, Steam Mobil DTE 790 Oil Series ...............................................8Mobil DTE Oil Named Series .......................................10

Mobil Product Book.qxd 6/25/04 4:09 PM Page xiii chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Gui

xiv


AT

1 (800) 662-4525


Mobil Product Book.qxd 6/25/04 4:09 PM Page xiv chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guid

1

Curve Grease 213 is a 3% molybdenum disulfide fortified rail curve and wheel flange grease. The ability of this greaseto adhere to wheel flanges is outstanding. It contains special additives which reduce the loss of lubricant that occurswhen high-speed trains pass over the treadles, or when the lubricant is applied on the locomotive wheel flange or railgauge face.

PenetrationNLGI at 77°F Base Oil Viscosity Drop Point %

Product Grade Thickener Structure Color Worked cSt at 40°C °C (°F) Moly

Curve Grease 213 1 Lithium Smooth/Tacky Gray/Black 325 100 177 (350) 3.0

Gargoyle Arctic Oils are naphthenic oils with very low pour points for the lubrication of reciprocating and rotaryrefrigeration compressors. They may be used with all types of refrigerants except HFC-134a and sulfur dioxide. They aresuitable for a wide range of conditions. Gargoyle Arctic Oil 155 has a Freon-12 floc point of -33°F. Gargoyle Arctic Oil300 has a Freon-12 floc point of -24°F. (Use with ammonia in screw compressors could cause sludge under severeoperating conditions.) Gargoyle Arctic Oil C Heavy is recommended as low temperature circulating oil in refrigerationcompressors when intimate mixing with refrigerant is not expected. Gargoyle Arctic Oil C Heavy has a Freon-12 flocpoint of -33°F.

Viscosity Spec. Pour Flash cSt at cSt at ISO

Product Grav. °F °F 40°C 100°C V.I. VG

Gargoyle Arctic Oil 155 0.913 -44 374 30 4.5 20 32Gargoyle Arctic Oil C Heavy 0.907 -44 383 46 5.6 30 46Gargoyle Arctic Oil 300 0.921 -44 392 65 6.7 32 68

Gargoyle Arctic SHC 200 Series are synthetic hydrocarbon fluids for the lubrication of refrigeration compressorsoperating in severe service. Gargoyle Arctic SHC 200 Series oils are suitable for systems using refrigerants such asR12, R114, and ammonia. They may also be used with R22 systems, provided the cooling system is designed for apartially miscible lubricant. Their Freon-12 floc point is -60°F. Gargoyle Arctic SHC 200 Series fluids are recommendedfor reciprocating and rotary compressors. They have USDA H-1 approval for incidental contact with food.



Gargoyle Arctic SHC 224 0.827 -65 425 29 5.7 132 32Gargoyle Arctic SHC 226 0.834 -49 425 68 10.4 148 68Gargoyle Arctic SHC 230 0.846 -38 420 219 25.0 149 220Gargoyle Arctic SHC 234 0.850 -32 510 400 41.0 152 460

Mobil Product Book.qxd 6/25/04 4:09 PM Page 1 chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide

2

Mobil 1 Motorcycle Oils are synthetic fluids and are based on the same technology used in Mobil 1 products but havebeen optimized specifically for the needs of motorcycles. These products provide the highest level of protection formotorcycles. The unique properties of a synthetic fluid provide natural protection against viscosity shear-down and loss.They offer excellent flow characteristics at low temperatures to reduce wear at start-up, and they offer outstandingprotection against high temperature breakdown. Mobil 1 V-Twin 20W-50 is formulated specifically for 4-cycle V twinengines. Mobil 1 MX2T is designed for 2-cycle dirt bikes and Mobil MX4T 10W-40 is recommended for on-road, off-roadcompetition and high performance 4-cycle sport bikes.

Viscosity Grav. Pour Flash Cold Cranking Cold Pumping cSt at cSt at

Product API °C (°F) °C (°F) cP at °C cP at °C 40°C 100°C V.I.

Mobil MX4T 10W-40 30.5 -54 (-65) 253 (487) 2,900 @ -200 11,500 @ -30 86.0 13.8 164Mobil 1 V-Twin 20W-50 29.4 -51 (-60) 270 (518) 2,930 @ -100 8,500 @ -20 130.0 17.7 150Mobil 1 MX2T 29.1 -42 (-44) 88 (190) N/A N/A 90.0 13.7 152

Mobil 1 motor oils are manufactured from 100% synthetic base stocks. Their unique combination of high performancesynthetic fluids and proprietary additive systems enables Mobil 1 motor oils to offer advantages beyond theirconventional counterparts. Mobil 1 Racing 0W-30 is designed to protect engines even in grueling racing applications andhelps deliver maximum horsepower in all engine types and sizes. Mobil 1 motor oils are fully compatible withconventional motor oils. Mobil 1 motor oils are designed for passenger car and light duty truck gasoline or diesel enginesrequiring API Service SL, SJ or CF. Mobil 1 0W-20, 0W-30, 5W-30 and 10W-30 also meet ILSAC GF-3. Mobil 1 0W-40is formulated for newer European cars, especially those with advanced-technology, multivalve engines. Mobil 1 15W-50is suitable for high-performance cars, particularly hot-running or heavily loaded vehicles and high-tech imported cars.Mobil 1 Truck & SUV 5W-40 is formulated for diesel and gasoline engines in hard working trucks and SUVs.


Product API °F °F cP at °C cP at °C 40°C 100°C V.I.

Mobil 1 0W-20 -65 446 4,840 @ -35 13,100 @ -40 47.1 8.8 169Mobil 1 0W-30 34.5 -65 450 3,800 @ -35 15,000 @ -40 55.7 10.3 176Mobil 1 Racing 0W-30 34.7 -65 454 5,000 @ -35 15,000 @ -40 56 10.3 175Mobil 1 0W-40 33.6 -65 450 4,300 @ -35 21,900 @ -40 80.3 14.4 185Mobil 1 5W-30 32.8 -54 455 3,600 @ -30 12,500 @ -35 55.8 10.1 169Mobil 1 10W-30 30.8 -49 455 3,848 @ -25 10,700 @ -30 61.3 9.8 145Mobil 1 15W-50 32.5 -49 491 5,234 @ -20 14,050 @ -25 124.7 17.4 155Mobil 1 Truck & SUV 5W-40 34.2 -49 439 - - 102 14.8 151

Mobil 1 Synthetic ATF is a synthetic transmission fluid which provides exceptional performance over a wide range oftemperatures. Mobil 1 Synthetic ATF provides outstanding low temperature properties for enhanced operability. In manyfront-wheel drive vehicles and manual transmissions, Mobil 1 Synthetic ATF will provide excellent gear shifting andprotection under severe driving modes. Mobil 1 Synthetic ATF is a superior DEXRON III® and MERCON® qualifiedproduct which meets or exceeds the requirements of Allison C-4, Denison HF-0 pump test, Vickers 35VQ25 vane pumptest and Sundstrand piston pump tests. It can also provide good performance in cars originally requiring Ford Type H(M2C166-H) and CJ (M2C138-CJ) fluids. It is not a substitute for Chrysler Type 7176 ATF. Mobil 1 Synthetic ATF iscompatible with mineral oil products and all common seal materials.

Viscosity Grav. Pour Flash cP at cP at cSt at cSt at

Product API °F °F -40°C -20°C 40°C 100°C V.I.

Mobil 1 Synthetic ATF 37.6 -65 428 6,200 850 35 7.6 198


3

Mobil 1 Synthetic Gear Lubricant is a 75W-90 multipurpose, synthetic gear oil. This Indy 500 certified product reduceswear and spalling under the high-speed, high-torque, and high horsepower conditions in competitive racing and high-performance cars. Mobil 1 Synthetic Gear Lubricant offers maximum resistance to oil breakdown from heat and high-speed operation, thereby extending service life. It reduces chatter in limited-slip differentials. It also contributes toimproved fuel economy when used with Mobil 1 Series or Mobil Delvac 1 synthetic engine oils. Mobil 1 Synthetic GearLubricant meets API Service GL-5, MT-1. It can also be used in rear axles where an API service GL-4 lubricant isrecommended. It should not be used in any transmissions requiring an engine oil or ATF or GL-4 performance level.

Viscosity Grav. Pour Flash cSt at cSt at

Product API °F °F 40°C 100°C V.I.

Mobil 1 Synthetic Gear Lubricant 33.8 -55 401 120 15.9 140

Mobil 1 Synthetic Grease is formulated with synthetic base stocks and a lithium complex thickener. The high viscositybase stock and additives give Mobil 1 Synthetic Grease the ability to lubricate over a wide temperature range, -37°C to+232°C (-35°F to +450°F). It resists water intrusion for proper lubrication of disc brake wheel bearings, suspension jointsand steering linkages. This grease provides excellent lubrication protection for components operating under the mostsevere conditions.

Penetration Base Oil ViscosityNLGI at 77°F Drop Point cSt at cSt at Color

Product Grade Thickener Worked Structure °C (°F), min 40°C 100°C Visual

Mobil 1 Synthetic Grease 2 Lithium 280 Smooth/ 288 (550) 220 23.8 RedComplex Slight Tack

Mobil 1 Synthetic Spray Lubricant is a multipurpose spray lubricant that combines the synthetic base stock technologyof Mobil 1 engine oil with additives designed specifically for spray lubricant applications. Mobil 1 Synthetic SprayLubricant lubricates, protects and cleans, displaces moisture, stops squeaks, and penetrates and loosens rusted parts. Itcan be used as an around-the-house, industrial, shop, vehicle or boat, general purpose lubricant for gears, hinges,chains, cables, metal parts, joints or surfaces. It will protect metal surfaces from water, rust or corrosion and clean metalsurfaces of gum, dirt and grease.

Viscosity Spec. Flash cSt at

Product Grav. °C (°F) 40°C

Mobil 1 Synthetic Spray Lubricant 0.815 45 (113) 4.0

Mobil Aero HF is an aviation hydraulic fluid that is U.S. Military Specification MIL-PRF-5606 approved. It is intendedprimarily for military aircraft and is designated as a NATO code H-515 fluid. It also meets the “super clean” requirementsdefined by the low particle count specification.

Flash Viscosity Spec. Pour (PMCC) cSt at cSt at cSt at Color

Product Grav. °F °F -40°C 40°C 100°C Visual V.I.

Mobil Aero HF 0.882 -85 200 460 13.9 5.1 Red 370


4

Mobil Aero HFA fluid is a mineral-base aviation hydraulic fluid of exceptionally high VI and low pour point. It is suitable foruse at temperatures down to -54°C (-65°F). The oil is nongumming, noncorrosive and highly resistant to oxidation. It hasthe approval of leading manufacturers of aircraft hydraulic equipment. It is also used in industrial equipment for extremelow-temperature applications. This product meets the obsolete U.S. Military Specification MIL-H-5606A quality level.

Flash Viscosity Spec. Pour (COC) cSt at cSt at cSt at Color

Product Grav. °F °F -40°C 40°C 100°C Visual V.I.

Mobil Aero HFA 0.882 -85 225 450 13.9 5.1 Red 370

Mobil Almo 500 Series air-driven rock drill oils possess high EP characteristics as well as excellent protection againstrust. The formulation offers an optimum balance of adhesiveness, yet is emulsifiable enough to pick up moisture carriedin the air stream. Mobil Almo 500 Series oils meet all tests and specifications established for heavy-duty rock drill oils.They are also well suited for saw guide operations in the pulp and paper industry because of their good metal-wettingproperties.


Product Grav. °C °C 40°C 100°C V.I. VG

Mobil Almo 525 0.883 -24 188 46 7.3 105 46Mobil Almo 527 0.899 -30 204 113 11.4 91 100Mobil Almo 529 0.893 -24 232 172 16.5 102 150Mobil Almo 532 0.902 -21 232 320 24.9 99 320

Mobil Arctic Turbine 150 is a paraffinic petroleum lubricating oil. This oil has low pour point characteristics and anadditive system designed primarily for service in bearing circulation systems of industrial gas turbines and centrifugalcompressors.

Viscosity Spec. Pour Flash cSt at cSt at

Product Grav. °C °C 40°C 100°C V.I.

Mobil Arctic Turbine 150 0.864 -30 190 32 5.0 95

Mobil Type F ATF is a Type F automatic transmission fluid that is approved against Ford specification M2C33-F. Itprovides optimum performance in transmissions that still require these specific frictional characteristics for smooth,positive shifting with long-term retention of these properties. Mobil Type F ATF has excellent low-temperature, antifoam,antiwear, and antideposit control characteristics.

Viscosity Grav. Pour Flash cSt at cSt at Color

Product API °F °F 40°C 100°C Visual V.I.

Mobil Type F ATF 31.4 -40 320 36 7.2 Red 168

Mobil Aviation Grease SHC 100 is a high performance grease which combines a synthesized hydrocarbon base fluidwith a lithium complex thickener. The unique physical properties of the synthetic base oil, combined with selectedadditives, provide outstanding protection against wear, rust, corrosion, and oxidation. Mobil Aviation Grease SHC 100 isrecommended for aviation applications, which need a lubricant that can function normally in extremely high or lowtemperatures. It has an operating range between -50°F to 180°F. Mobil Aviation Grease SHC 100 is particularly suitablefor use in commercial aircraft wheel bearings. Mobil Aviation Grease SHC 100 is approved for use by all the majoraircraft wheel and brake manufacturers including Honeywell/Allied Signal, Goodrich, Messier-Bugatti, ABS, Dunlop, andCleveland.


Product Grade Thickener Worked Structure °C (°F) 40°C 100°C Visual

Mobil Aviation Grease SHC 100 2 Lithium 280 Smooth/ 260 (500) 100 14.5 RedComplex Slight Tack


5

Mobil Centaur Moly 1 & 2 are high performance greases formulated with advanced calcium sulfonate thickenertechnology. Unlike conventional soap-base thickeners, the calcium sulfonate thickener imparts excellent corrosion andwater-resistance properties to the grease, and has inherent extreme pressure properties that enhance load-carryingability. Fortified with molybdenum disulfide to complement its robust extreme-pressure additive system, Mobil CentaurMoly greases are particularly well suited to meet the demanding lubrication requirements of heavy-duty trucks (king pins,tie rods, u-joints, hinge & bucket pins, and fifth wheels), construction and mining equipment, and heavily loaded industrialbearings. Mobil Centaur Moly greases also provide outstanding resistance against the effects of water washout, waterspray-off and corrosion.

ViscosityNLGI Thickener Penetration Drop Point cSt at ColorProduct Grade Type Worked 60x °C(°F) 40°C Visual

Mobil Centaur Moly 1 1 Calcium Sulfonate 325 288(550) 320 GrayMobil Centaur Moly 2 2 Calcium Sulfonate 265 280(536) 320 Gray

Mobil Cylinder Oils are four premium quality, high viscosity lubricants designed for use in steam cylinders, wormgearboxes, couplings and bearings. These oils are designed to protect against rust and corrosion, and provide good filmstrength, excellent lubricity and resistance to oxidation, foaming, and the washing effect of moisture. Mobil Cylinder Oilsare compounded with lubricity agents.

Viscosity Spec. Pour Flash cSt at cSt at Color ISO

Product Grav. °C °C 40°C 100°C Visual V.I. VG

Mobil 600W Cylinder Oil 0.801 -9 282 375 27.0 Dark Brown 99 320/460Mobil 600W Super Cylinder Oil 0.900 -6 282 465 30.5 Green 95 460Mobil Extra Hecla Super Cylinder Oil 0.905 0 282 675 35.8 Dark Green 85 680Mobil Extra Hecla Super Cylinder Oil Mineral 0.904 3 288 1000 43.0 Dark Green 80 1000

Mobil Delvac 1 5W-40 is a supreme performance, fully synthetic heavy duty diesel engine oil that helps extend enginelife, while providing long drain capability and enhanced fuel economy for diesel engines operating in severe applications.The state-of-the-art technology behind Mobil Delvac 1 delivers exceptional performance in both modern, low-emissionengines, including refrigerated units, and older, well-maintained engines. Mobil Delvac 1 5W-40 is recommended for usein a wide range of heavy-duty applications and operating environments found in the trucking, mining, construction, andagricultural industries. It is also suitable for gasoline service in mixed diesel/gasoline fleets.

Mobil Delvac 1 meets or exceeds the following requirements: API CI-4, CH-4/SL; ACEA E5/E4/E3; Caterpillar ECF-1;Cummins CES 20078/20077/20076; Detroit Diesel DDC 7SE 270 (Four Stroke Cycle); Global DHD-1; JASO DH-1; MackEO-N Premium Plus 03 and EO-M Plus; Mercedes Benz 288.5; Volvo VDS-3/VDS-2. Mobil Delvac 1 is alsorecommended for use in applications requiring Allison C-4 and Renault RVI RXD.

Viscosity Grav. Pour Flash cSt at cSt at % Sulf.

Product API °F °F 40°C 100°C Ash TBN V.I.

Mobil Delvac 1 34.1 -49 439 102 14.8 1.35 12.0 151


6

Mobil Delvac 1300 Super 10W-30 and 15W-40 are extra high performance heavy duty diesel engine oils that help extendengine life in the most sever on- and off-highway applications. The advanced compenetry of these products deliversexceptional performance in both modern, low-emission engines, as well as older engines operating on low or high sulfurfuel. Mobil Delvac 1300 Super 10W-30 and 15W-40 are recommended for use in a wide range of heavy duty applicationsand operating environments found in the trucking, mining, construction, quarrying, and agricultural industries. MobilDelvac 1300 Super 10W-30 and 15W-40 also meet the latest API specifications for gasoline engines and mixed fleets.

Mobil Delvac 1300 Super 15W-40 meets or exceeds the following requirements: API CI-4, CH-4/SL; ACEA E5;Caterpillar ECF-1; Cummins CES 20078/20077/20076; Detroit Diesel DDC 7SE 270 (Four Stroke Cycle); Global DHD-1;JASO DH-1; Mack EO-N Premium Plus 03 and EO-M Plus; Mercedes Benz 228.3; Volvo VDS-3/VDS-2, and is alsorecommended for use in applications requiring Allison C-4. Mobil Delvac 1300 Super 10W-30 meets or exceeds API CI-4, CH-4/SL; Caterpillar ECF-1; Cummins CES 20078/20076; JASO DH-1; Mack EO-M Plus; Volvo VDS-3/VDS-2.



Mobil Delvac 1300 Super 10W-30 31.9 -22 444 74 11.5 1.3 12 145Mobil Delvac 1300 Super 15W-40 29.5 -22 446 123 15.6 1.3 12 133

Mobil Delvac 1630, 1640, and 1650 are high performance monograde diesel engine oils formulated from advancedtechnology components. They are specifically engineered for performance in intercooled, turbocharged engines operatingunder severe on and off-highway conditions. Mobil Delvac 1600 monogrades are used in a wide range of applicationswhere a monograde lubricant is recommended. Mobil Delvac 1630 and 1640 meet or exceed API CF/SF; MTU Type 2;Mercedes Benz 228.2; MAN 270; Mobil Delvac 1630 is suitable for use in applicaitons requiring Allison C-4. Mobil Delvac1650 meets or exceeds API CF/SF.



Mobil Delvac 1630 27.7 -22 482 90 11.5 1.4 12.0 117Mobil Delvac 1640 27.1 -6 493 132 14.7 1.4 12.0 112Mobil Delvac 1650 26.4 0 554 202 19.5 1.4 12.0 110

Mobil Delvac Hydraulic 10W is a hydraulic oil intended for use in mobile and stationary heavy-duty applications. Theproduct is formulated with high quality base stocks and a unique additive system that has been optimized for hydraulicapplications. Mobil Delvac Hydraulic 10W offers effective resistance to wear, oxidation and foaming, and meets Vickers35VQ25 requirements. This product has excellent low temperature properties and a high viscosity index offering excellentperformance in a broad range of operating temperatures.

Viscosity Grav. Pour Flash cP at cSt at cSt at

Product API °F °F -30°C 40°C 100°C V.I.

Mobil Delvac Hydraulic 10W 29.7 -22 450 19,000 37.7 6.1 107

Mobil Delvac Xtreme Service Grease is a high performance, heavy-duty truck and heavy equipment grease withexcellent extreme-pressure and antiwear properties. It contains a high viscosity base oil and a lithium complex thickener toprovide heavy-duty, extended service and water spray-off resistance. The lithium soap, combined with an advancedadditive system, deliver outstanding high-temperature performance properties. It is recommended for the lubrication ofheavy-duty and extended service automotive and off-highway mobile equipment. It is also an excellent fifth wheel lubricant.



Mobil Delvac Xtreme Service Grease 2 Lithium 280 Smooth/ 260 (500) 320 25 OrangeComplex Very Tacky


7

Mobil Drive Clean Plus passenger vehicle engine oils offer synthetic blend formulas tailored to the needs of both newervehicles and high mileage vehicles. These products are a special combination of premium base oils, high-performancesynthetic fluid and 23% more performance additives than Mobil's conventional motor oil. Compared to conventional motoroil, regular use of Mobil Drive Clean Plus Newer Vehicle Formula Synthetic Blend 5W-30 helps: protect critical engineparts; prevent deposit formation in your engine; keep your engine running cleaner longer; and provide longer-lastingprotection for hard-working cars and light-duty trucks. Regular use of Mobil Drive Clean Plus High Mileage FormulaSynthetic Blend 10W-30 (and 10W-40) helps: clean deposits, build-up and sludge; condition seals to prevent leaks (note:No motor oil can repair damaged seals.); reduce oil consumption; protect critical engine parts; and restore engineperformance.



Mobil Drive Clean Plus 5W-30 33.0 -42 218 5,860 @ -30 20,800 @ -35 65.0 10.9 159Mobil Drive Clean Plus 10W-30 30.8 -36 228 6,290 @ -25 21,800 @ -30 75.0 11.4 145Mobil Drive Clean Plus 10W-40 30.9 -30 230 6,520 @ -25 24,400 @ -30 97.4 14.3 151

Mobil Drive Clean Oil HD 30 is a mono-grade passenger vehicle engine oil formulated from quality base stockscombined with modern detergents, dispersants, antioxidants, and antiwear additives. It is designed to help keep enginesclean and protect against sludge, deposit formation, rust and corrosion under normal engine operating conditions. MobilDrive Clean Oil HD 30 meets the latest requirements of API SL. It is recommended for use in vehicles or otherapplications that require a mono-grade SAE 30 engine oil.



Mobil Drive Clean Oil HD 30 22.7 0 428 99 11.8 107

Mobil Drive Clean Oils are passenger vehicle engine oils formulated from quality base stocks combined with moderndetergents, dispersants, antioxidants, and antiwear additives. These oils are designed to help keep engines clean andprotect against sludge, deposit formation, rust and corrosion under normal engine operating conditions. Mobil DriveClean 5W-20 is specifically designed for late Model Ford and Honda vehicles that recommend a 5W-20 product. MobilDrive Clean 5W-20 meets Ford specification ESE-M2C-153H. It is recommended for gasoline powered cars and lighttrucks that manufacturers’ require this viscosity grade such as 2001 and newer Ford and newer Honda automobiles. It isnot recommended for use in other vehicles unless a 5W-20 is recommended. Mobil Drive Clean 5W20, 5W-30 and 10W-30 meet the latest requirements of API SL and ILSAC GF-3 and are recommended for gasoline powered cars and lighttrucks. For older vehicles or vehicles that require a higher viscosity grade, Mobil Drive Clean 10W-40 and 20W-50 arerecommended. These products meet API SL.



Mobil Drive Clean 5W-20 33.5 -33 392 2,200 @ -25 13,200 @ -35 47 8.3 153Mobil Drive Clean Oil 5W-30 33.0 -38 392 5,500 @ -30 17,000 @ -35 62 10.5 159Mobil Drive Clean Oil 10W-30 30.0 -33 392 6,200 @ -25 20,000 @ -30 70 10.4 134Mobil Drive Clean Oil 10W-40 29.3 -27 392 6,100 @ -25 35,000 @ -30 97 14.0 147Mobil Drive Clean Oil 20W-50 27.4 -17 392 8,200 @ -15 24,000 @ -20 162 18.1 124


8

Mobil DTE 10M Series oils are super premium, wide-temperature, antiwear hydraulic oils with additives for maximizedprotection. They provide keep-clean performance and are super-stabilized to provide improved filterability, demulsibility,and multimetal compatibility in the presence of water. The Mobil DTE 10M Series oils provide outstanding antiwearprotection in all standard industry tests, and are ExxonMobil’s primary recommendation for hydraulic applications wherelow ambient temperatures or rapid changes from low to high temperatures are encountered.



Mobil DTE 11M 0.871 -48 390 15 3.9 140 15Mobil DTE 12M 0.871 -48 390 22 4.9 149 22Mobil DTE 13M 0.877 -45 410 33 3.7 141 32Mobil DTE 15M 0.875 -42 420 32 6.1 141 46Mobil DTE 16M 0.879 -45 427 46 7.9 131 68Mobil DTE 18M 0.887 -37 442 100 12.8 124 100Mobil DTE 19M 0.892 -36 514 150 16.6 118 150

Mobil DTE 20 Series oils are super premium antiwear industrial hydraulic oils developed to meet the requirements of allconventional and high-output hydraulic systems. Mobil DTE 21, 24, 25, and 26 contain an excellent balance of selectedhigh-quality base stocks, antiwear agents, and stabilizers for maximized keep-clean and antiwear protection. These premiumhydraulic oils are ExxonMobil’s primary recommendation for most hydraulic applications in industrial, marine, and mobileservice, including high-pressure systems, systems with servo valves, and all robotics in industrial service. Mobil DTE 21 isspecifically formulated to meet the exacting requirements for spindle oils set by machine tool manufacturers. In addition,these products are approved in Vickers, Denison HF-0 pump tests.



Mobil DTE 21 0.850 -22 345 10 2.7 98 10Mobil DTE 24 0.871 -17 428 32 5.3 98 32Mobil DTE 25 0.876 -17 450 46 6.7 98 46Mobil DTE 26 0.881 -6 457 68 8.5 98 68

Mobil DTE 724 Oil is a gas turbine oil that was developed for higher-output gas turbines such as the General Electric Heavy-Duty Gas Turbine Frame 7000. These turbines demand a lubricant having a higher level of thermal and oxidative stability thanconventional steam turbine oils. Mobil DTE 724 Oil meets General Electric specification GEK-32588C & -32588F.

Viscosity Spec. Pour Flash cSt at cSt at TOST, ISO

Product Grav. °C °C 40°C 100°C Hours V.I. VG

Mobil DTE 724 Oil 0.866 -12 221 32.0 5.4 7000 107 32

Mobil DTE 790 Oil Series are premium steam turbine oils made from specially refined, high pressure hydrotreated baseoils combined with additives that provide exceptional chemical stability, outstanding resistance to oxidation, superiordemulsibility, and excellent protection against rust, and deposits. The additives in the DTE 790 Oil Series form atenacious wear-resistant film on exposed metal surfaces that greatly minimizes wear during the starting and stopping ofthe turbines. Mobil DTE 790 Oil Series are recommended for use in the circulation systems of direct-connected steamturbines and ring-oiled bearings of geared or direct-connected turbines.

Viscosity Spec. Pour Flash cSt at cSt at TOST ISO


Mobil DTE 797 Oil 0.85 -7 221 30 5.2 6,500 110 32Mobil DTE 798 Oil 0.862 -6 232 44 6.5 5,500 1106 46Mobil DTE 799 Oil 0.862 -6 232 65 8.6 4,500 97 68


9

Mobil DTE 800 Series oils are super premium turbine oils made from specially refined hydrotreated base oils combinedwith a customized additive package. They have been developed for high-output gas and steam turbines. They are idealfor combined cycle applications or for the power generator with both steam and gas turbines. Mobil DTE 832 meets thefollowing specifications.

Viscosity Spec. Pour Flash cSt at cSt at TOST ISO


Mobil DTE 832 0.860 -30 224 29.6 5.4 10,000+ 110 32Mobil DTE 846 0.873 -30 244 42.4 6.1 10,000+ 106 46

Mobil DTE Excel Series are super premium, non-zinc, antiwear hydraulic oils that meet the requirements for high-speed,high-pressure piston, vane and gear pumps. These oils are balanced to provide excellent thermal and hydrolytic stability,very good compatibility with metal working coolants and exceptional corrosion protection for copper-based alloys used inaxial piston pumps. These products meet or exceed the requirements of Denison HF-0, Vickers and Cincinnati MilacronP-68, P-70 and P-69.



Mobil DTE Excel 32 0.870 -27 432 33 5.4 97 32Mobil DTE Excel 46 0.880 -27 438 46 6.7 97 46Mobil DTE Excel 68 0.880 -27 457 68 8.5 97 68

Mobil DTE FM 32 offers good antiwear hydraulic pump protection, excellent oxidation stability, and protection againstrust in multiservice applications in the lubrication of food machinery. It is formulated with non-toxic USDA food-gradeadditives and base oils, qualifying it as a Category H-1 oil under Title 21 CFR 178.3570 for lubricants having incidentalcontact with food.*



Mobil DTE FM 32 0.861 10 413 31.9 5.5 106 32

*Listed with NSF.


10

Mobil DTE Oil Named Series are premium-quality, rust and oxidation inhibited oils designed for use in multifunctionalreuse applications such as steam or gas turbines, hydraulic systems, and other industrial applications where long oil lifeis required. They are manufactured from highly refined turbine oil stocks blended with proper additives to produce a trulyservice-balanced oil.



Mobil DTE Oil Light 0.867 -36 218 30 5.1 102 32Mobil DTE Oil Medium 0.873 -27 221 44 6.5 98 46Mobil DTE Oil Heavy Medium 0.877 -27 223 65 8.4 95 68Mobil DTE Oil Heavy 0.881 -24 237 95 10.9 92 100Mobil DTE Oil Extra Heavy 0.887 -21 272 146 14.7 96 150Mobil DTE Oil BB 0.890 -18 284 218 18.8 96 220Mobil DTE Oil AA 0.897 -12 286 325 24.7 96 320Mobil DTE Oil HH 0.900 -15 288 436 29.4 95 460

Mobil DTE PM Series oils are super premium paper machine circulation system oils. Mobil DTE PM oils are formulatedfrom stable, high quality base stocks and additives to provide superior protection against rust and corrosion, excellentresistance to oxidation and thermal degradation, and a high level of antiwear performance. Mobil DTE PM oils have gooddemulsibility, which permits water and other contaminants to separate readily from the oil in the system reservoir, andgood air release properties to prevent noisy and erratic operation.



Mobil DTE PM 100 0.885 -6 240 100 11.4 95 100Mobil DTE PM 150 0.891 -6 250 150 14.8 95 150Mobil DTE PM 220 0.893 -6 260 220 19.1 95 220Mobil DTE PM 320 0.895 -6 250 320 25.4 95 320Mobil DTE PM Ashless 150 0.890 -9 274 150 14.6 97 150Mobil DTE PM Ashless 220 0.894 -6 282 220 18.7 97 220

Mobil EAL 224H is an antiwear hydraulic oil for most hydraulic systems requiring readily biodegradable, nontoxic fluids. Itcan be used in industrial, marine, and mobile service, including high-pressure systems, systems with servo valves, and allrobotics. It is formulated from select, high-quality, high-VI vegetable oils and additives which provide the propertiesrequired in hydraulic fluids while satisfying the stringent criteria for biodegradability and toxicity. Mobil EAL 224Hprovides the excellent antiwear and film-strength characteristics necessary for hydraulic systems operating undermoderate conditions. Its 12-stage rating in the FZG Gear Test demonstrates a high level of protection against wear andscuffing. It is approved in the Vickers V-104C and 35VQ25 and various piston pump tests, and meets the requirements ofDenison HF-0 and the TP30283A vane pump tests.



Mobil EAL 224H 0.922 -18 428 37 8.4 213 32-46


11

Mobil EAL Arctic Series synthetic refrigeration compressor lubricants are formulated from selected polyol esterbasestocks and unique additives which provide outstanding lubricity, wear protection, chemical and thermal stability, andproper miscibility. The products, part of the Mobil EAL (Environmental Awareness Lubricants) family, are specificallydeveloped to lubricate compressors and system components where HFC refrigerants are used. HFCs are ozone-friendly,chlorine-free refrigerants which are replacing CFCs in the world market. The performance of Mobil EAL Arctic Serieslubricants has been well documented with HFCs in a wide range of refrigeration and air conditioning systems. Mobil EALArctic Series products are available in ISO viscosity grades 22 through 68. Mobil EAL Arctic 22 CC is a special gradeof the Mobil EAL Arctic Series that is formulated for use specifically in Copeland refrigeration compressors. The othergrades are suitable for use in domestic, commercial and industrial refrigeration and air conditioning systems where HFCrefrigerants are used. The products meet the performance requirements of many major compressor and system buildersaround the world.



Mobil EAL Arctic 22 1.002 -70 453 22 4.6 114 22Mobil EAL Arctic 22 CC 0.991 -65 428 23.5 4.91 130 22Mobil EAL Arctic 32 0.986 -54 446 32 5.5 109 32Mobil EAL Arctic 46 0.975 -44 455 46 6.9 104 46Mobil EAL Arctic 68 0.969 -33 464 65 8.3 101 68

Mobil EAL Envirosyn H Series are synthetic antiwear hydraulic oils for most hydraulic systems requiring very highperformance hydraulic and circulating oils which are readily biodegradable and virtually non-toxic. They meet or surpassMannesmann Rexroth, Sauer Sundstrand, Denison and Vickers specifications. Mobil EAL Envirosyn H oils areformulated from high viscosity index synthetic ester basestocks and an advanced additive package which providesexcellent oxidation stability, antifoam performance and controlled low-temperature flow properties. They can be used inindustrial, marine, and mobile service, including high pressure systems, systems with servo valves and all robotics.



Mobil EAL Envirosyn 32H 0.870 -38 514 33 6.4 147 32Mobil EAL Envirosyn 46H 0.874 -49 500 44 7.9 145 46Mobil EAL Envirosyn 68H 0.884 -38 511 69 10.1 138 68Mobil EAL Envirosyn 100H 0.914 -44 534 99 13.5 136 100

Mobil Glygoyle 22 and 30 severe-duty polyglycol lubricants are a family of fully synthetic industrial lubricants developedspecifically for use under operating conditions that are beyond the capabilities of mineral oils in plain and antifrictionbearings, enclosed industrial gears, and compressors. These lubricants provide superior wear protection, good protectionagainst corrosion in both the liquid and vapor phases, excellent lubricity to decrease friction and bulk oil temperatures,and outstanding thermal and oxidation stability. They are compatible with most seals and gaskets, but do not mix withmineral oils. They are recommended for air compression in either reciprocating or rotary compressors.



Mobil Glygoyle 22 1.007 -41 229 177 25.1 173 -Mobil Glygoyle 30 1.006 -41 221 224 30.9 181 220


12

The Mobil Glygoyle HE Series lubricants are synthetic highly efficient worm gear lubricants made with polyglycol base fluids.They must be kept dry because they do not separate from water and are hygroscopic. They provide a low traction coefficient,therefore, the sliding contacts common to worm gear lubrication generate very low levels of heat, minimizing energy consumption.


Product Grav. °C °C 40°C 100°C V.I.

Mobil Glygoyle HE 460 1.05 -30 268 460 77 240Mobil Glygoyle HE 680 1.05 -20 265 680 114 257

Mobil Infinitec 152 is the brand name of an outstanding grease for automotive wheel bearing and chassis applications. It isdesigned to meet the high-temperature/high-load demands of four-wheel drive truck and sport-utility vehicle wheel bearings. It isrecommended for sealed-for-life industrial bearing applications, as well as multi-purpose applications where water resistenceand extreme-presure properties are important. Its low oil-bleed properties allow it to be used where minimal leakage is critical.Mobil Infinitec 152 is formulated with a patented lithium-complex thickener system. This unique technology gives the greaseup to five times the high-temperature lubrication life over conventional multi-purpose greases.* In additon to high-temperaturestability, its 60-lb Timken OK Load and 315-kg-four-ball weld testify to its excellenct extreme presure performance. It contains apolymer that resists the effects of water washout and spray-off. Mobil Infinitec 152 has exceptionally good resistance to shear.Mobil Infinitec 152 exceeds ASTM GC-LB requirements for automotive wheel bearing and chassis applications.

NLGI Thickener Penetration Drop Point ViscositycSt atProduct Grade Tupe Worked 60X Structure °C(°F) 100°C Color

Mobil Infinitec 152 2 Lithium Complex** 285 Smooth and Homogeneous 280(536) 148 Blue

* As measued by typical ASTM D 3336 Results, ** Modified with proprietary lubrication life enhancing components.

Mobil Hydraulic Oil AW Series oils are premium antiwear hydraulic oils developed to meet the requirements of allconventional and high-output industrial hydraulic systems. Mobil Hydraulic Oil AW Series consist of five viscosity grades.These antiwear oils meet major hydraulic pump and component manufacturers’ specifications, including the Denison HF-0,and Vickers I-286-S and M-2950-S, (AW 32, 46 & 68). The five AW grades are recommended for use in most hydraulicsystems with gear, vane, radial piston and axial piston pumps where pressures and speeds require an antiwear product.



Mobil Hydraulic Oil AW 32 0.873 -11 374 32 5.4 95 32Mobil Hydraulic Oil AW 46 0.876 -11 388 46 6.7 95 46Mobil Hydraulic Oil AW 68 0.882 0 399 68 8.5 95 68Mobil Hydraulic Oil AW 100 0.885 5 399 100 11.1 95 100Mobil Hydraulic Oil AW 150 0.881 0 420 150 14.6 95 150


13

Mobil Jet Oil II, a second-generation synthetic lubricant, meets all the lubrication requirements of high-performanceaircraft gas turbine engines of the turbo-jet, turbo-fan, turbo-prop, and turbo-shaft (helicopter) types in commercial andmilitary service. It also is recommended for aircraft-type gas turbines in industrial and marine applications. Benefits fromits use include reduced oil consumption, extended periods between oil drains, extended intervals between engineoverhauls, and reduced unscheduled downtime because of lubrication related problems. Mobil Jet Oil II is approvedagainst U.S. Military Specification MIL-PRF-23699. In addition, it is approved by Pratt & Whitney Aircraft Group, UnitedTechnologies Corp.; RR/Allison Engine Co.; SNECMA; IAE; and General Electric Co. for their commercial turbineengines. It also is approved by numerous accessory manufacturers, and other turbine engine builders.

Viscosity Spec. Pour Flash cSt at cSt at cSt at

Product Grav. °F °F -40°C 40°C 100°C

Mobil Jet Oil II 1.0035 -74 518 11,000* 27.6 5.1

* Percent change at -40°C after 72 hours = 0.15%

Mobil Jet Oil 254 is a third-generation synthetic lubricant designed for advanced aircraft gas turbine engines of the turbo-jet, turbo-fan,turbo-prop, and turbo-shaft (helicopter) types in commercial and military service. It also is suitable for aircraft-type turbine engines inindustrial or marine service. Mobil Jet Oil 254 provides important performance advantages over Type II engine oils. Benefits from its useinclude bulk oil oxidation reduced by up to 50 percent, deposit control, reduced sludge and carbon deposit formation, longer seal andbearing life, and reduced oil consumption. Mobil Jet Oil 254 is approved against U.S. Military Specification MIL-PRF-23699, highthermal stability (HTS) classification. In addition, it is approved by Pratt & Whitney Aircraft Group, United Technologies Corp.; RR/AllisonEngine Co.; SNECMA; IAE; and General Electric Co. for their commercial turbine engines. It also is approved by numerous accessorymanufacturers, and other turbine engine builders.

Viscosity Spec. Pour Flash cSt at cSt at cSt at

Product Grav. °F °F -40°C 40°C 100°C

Mobil Jet Oil 254 1.0044 -80 489 11,500* 26.4 5.3

* Percent change at -40°C after 72 hours = 2.2%

Mobil Mist Lube Series oils comprise a family of oils which meet the lubrication requirements of machine componentssupplied by oil-fog or oil-mist methods. These oils are easily misted through proper devices and can be readilyreclassified to large drops on bearing surfaces. They provide excellent wear protection against heavy loads and havegood surface-wetting characteristics. The objectionable oil-mist migration common to other oils is almost completelyabsent when these products are used in properly designed and adjusted systems. Further, they have a good EP ratingand oxidation stability. These products have proven to be outstanding mist lubricants for bearings, gears, screws, andmetallic ways. Mobil Mist Lube 32 and 34 oils, which are needed for heavily loaded bearings, usually require thermalmisting devices.



Mobil Mist Lube 24 0.88 -12 210 32 6 110 32Mobil Mist Lube 27 0.89 -12 234 98 11 95 100Mobil Mist Lube 32 0.90 -9 230 320 25 100 320Mobil Mist Lube 34 0.90 -6 238 460 32 100 460


14

Mobil Mercon V Synthetic Blend ATF is a premium synthetic blend lubricant for automatic transmissions and otherapplications that require a fluid satisfying Ford’s Mercon® V specification or General Motor’s Dexron® -III or Dexron IIspecifications. It is also approved for applications where a Ford Mercon type fluid is recommended. Additionally, MobilMercon V Synthetic Blend ATF is suitable for use in both newer and older Chrysler automatic transmission applicationswhere ATF+3 or ATF+4 is recommended.

Viscosity Grav. Pour Flash cSt at cP at SUS at

Product API °C(°F) °C(°F) 100°C -40°C(-40°F) 100°C

Mobil Synthetic Blend ATF 34.1 -55(-67) 206(403) 7.5 10,500 -Mercon V

Mobil Multi-Purpose ATF is a premium automatic transmission fluid meeting many major U.S. and import carmanufacturers’ performance requirements. Mobil Multi-Purpose ATF is qualified by General Motors Corporation as aDEXRON® III fluid. It is qualified by Ford for its MERCON® requirement and may be used in cars requiring Ford Type CJand H fluids. It can also be used in off-highway transmissions, power steering, and other hydraulic systems requiring aAllison C-4 fluid. It is recommended for the exacting industrial hydraulic oils demands of Denison HF-0, Vickers vane, andSundstrand piston pumps.

Viscosity Grav. Pour Flash cP at cSt at cSt at Color

Product API °F °F -40°C 40°C 100°C Visual V.I.

Mobil Multi-Purpose ATF 31.3 -45 370 17,400 36 7.5 Red 184

Mobil Pegasus Products — Table of Name Changes

Mobil Pegasus 1 is a high-performance synthetic low ash natural gas engine oil ideal for most gas engines andoperating conditions. The product can provide optimum performance in Caterpillar, Superior, Waukesha, and otherturbocharged and naturally aspirated medium-to-high-speed gas engines requiring a low-to-medium ash level product.Mobil Pegasus 1 will also provide outstanding service in four-cycle gas engines starting and operating under very lowambient conditions and in remote control gathering field applications, or applications at very high operating temperatures.Mobil Pegasus 1, with its naturally higher viscosity index, provides a superior protective film at temperatures up to 38°C(100°F) above the limit for conventional mineral oils. It flows at -54°C (-65°F) without VI improvers. Also, Mobil Pegasus1 is ideally suited for co-generation and ebullient-cooled applications because of its wide temperature range and long oiland engine life protection.

Viscosity SAE Grav. Pour Flash cSt at cSt at % Sulf.

Product Grade API °C °C 40°C 100°C V.I. TBN Ash

Mobil Pegasus 1 15W-40 34.1 -48 238 94 13.0 136 6.5 0.51

Formerly Changed To

Mobil Pegasus 89 Mobil Pegasus 710

Mobil Pegasus 100/30 Mobil Pegasus 801-SAE 30

Mobil Pegasus 100/40 Mobil Pegasus 801

Mobil Pegasus 385 Mobil Pegasus 505-SAE 30


Mobil Pegasus 390 Mobil Pegasus 701-SAE 30





15

Mobil Pegasus 505-SAE 30 and Mobil Pegasus 505 (formerly Mobil Pegasus 385 and 485) are low ash natural gasengine oils that are SAE 30- and 40-grade oils respectively. They are premium quality gas engine oils formulated with lowash dispersants and additives that provide high-temperature antiscuff and antiscoring capabilities. They meet the specialrequirements of the most modern high-specific-output or ambient-rated turbocharged engines operating continuously at,or in excess of, rated capacity at high temperatures and high output. They also meet the requirements of slow-speed,two-cycle and four-cycle engines operating under normal service conditions. Mobil Pegasus oils are field proven andapproved by many builders of natural gas engines. Dresser-Rand, for example, approves Mobil Pegasus 505-SAE 30for naturally aspirated models (Category I), for low-level, turbocharged engines (Category II), and for high-levelturbocharged units (Category III).



Mobil Pegasus 505-SAE 30 30 29.0 -15 236 85 10 97 2.7 0.46Mobil Pegasus 505 40 28.0 -15 238 126 13 97 2.7 0.46

Mobil Pegasus 605 (formerly Mobil Pegasus 426) and Mobil Pegasus 610 (formerly Mobil Pegasus 446) are SAE 40-grade natural gas engine oils designed for engines running on landfill gas or sour gas. These require enough TBNreserve and alkalinity retention to neutralize acidic components such as Total Organic Halide as Chloride (TOHCI) and/orH2S at moderate levels. The products provide outstanding protection for turbocharged and naturally aspirated, medium-and high-speed, four-cycle Caterpillar, Superior, and Waukesha gas engines requiring a product of low to medium ashlevel. Mobil Pegasus 605 and 610 do not contain zinc or phosphorus, so can be used in both three-way and selectivecatalytic systems. They are highly dispersant oils with a special detergent additive system that protects against corrosion.Its lower ash level helps control combustion chamber ash build-up.



Mobil Pegasus 605 40 27.5 -15 262 124 14 100 4.9 0.52Mobil Pegasus 610 40 27.5 -18 264 130 14 102 8.6 0.98

Mobil Pegasus 701-SAE 30 and Mobil Pegasus 701 (formerly Mobil Pegasus 390 and 490) ashless natural gas engineoils are SAE 30- and 40-grade oils, respectively. They are premium-quality gas engine oils formulated with ashlessdispersants, effective oxidation and corrosion inhibitors, and antiwear agents. They provide excellent dispersancy, andgood high-temperature detergency and stability. Carbon and ash deposits are negligible. Mobil Pegasus 701-SAE 30and 701 are recommended for all high-speed gas engines. They are also suitable for modern two- and four-cycle, slow-speed gas engines except where severity of application requires special heavy-duty, load-carrying performance. MobilPegasus oils are field-proven and approved by many builders of natural gas engines. Dresser-Rand, for example,approves Mobil Pegasus 701-SAE 30 for naturally aspirated models (Category I) and for low-level turbocharged engines(Category II).



Mobil Pegasus 701-SAE 30 30 29.0 -15 238 85 10 97 2.2 0.07Mobil Pegasus 701 40 28.2 -15 249 132 13 97 2.2 0.07


16

Mobil Pegasus 710 (formerly Mobil Pegasus 89) is designed to provide the highest level performance and protection inSuperior, Waukesha, and other turbocharged and naturally aspirated, medium- to high-speed, four-cycle natural gasengines requiring a product of medium-ash level. It minimizes ash deposits in cooler-combustion, lean-burn engines andin stoichiometric engines showing lower levels of oil consumption. With its low levels of zinc and phosphorus, MobilPegasus 710 can be used in engines equipped with catalytic converters that require oils of medium ash content. It alsocan be used in gas engines when alternative sources for fuel gas contain low levels of chlorine and sulfur compounds.Mobil Pegasus 710 gas engine oil provides excellent oxidation, nitration, and thermal stability, reduced levels of carbonand sludge formation, and longer oil and filter life. It has superior resistance to foaming, exhibits good demulsibility, andprovides protection against corrosion.



Mobil Pegasus 710 40 28.0 -15 249 121 13 98 6.5 0.94

Mobil Pegasus 801-SAE 30 and Mobil Pegasus 801 (formerly Mobil Pegasus 100/30 and 100/40) oils are a newgeneration of ashless dispersant and antiscuff natural gas engine oils in SAE 30 and 40 viscosity grades. They areintended to provide superior cleanliness and optimum wear protection in the most severe engines and applications,without the disadvantage of ash deposits. Mobil Pegasus 801-SAE 30 and 801 gas engine oils have demonstratedsuperior performance over an exceptionally wide range of engines and operating conditions. These oils are the primaryrecommendation for mixed engine operations. Mobil Pegasus 801-SAE 30 is approved for all service levels of DresserRand (categories I, II and III).



Mobil Pegasus 801-SAE 30 30 28.9 -15 238 83 10 97 2.8 0.13Mobil Pegasus 801 40 28.2 -15 249 132 13.2 97 2.8 0.13

Mobil Pegasus 805 Series are SAE 40 and 15W-40 grade natural gas engine oils designed to provide excellentoxidation and nitration resistance, thermal stability and extended oil life in Caterpillar, Superior, Waukesha, and otherturbocharged, naturally aspirated, medium- to high-speed, four cycle gas engines requiring a low ash level product. Theyminimize ash deposits in lean-burn engines and in stoichiometric engines. Mobil Pegasus 805 and 805 Super can beused in engines equipped with catalytic converters and in engines utilizing alternate fuel sources that contain low levels ofchlorine and sulfur compounds. Mobil Pegasus 805 Super exhibits high-ash performance characteristics and offersoutstanding valve face and seat protection, optimized engine cleanliness, and control of deposit formation.



Mobil Pegasus 805 40 27.3 -12 262 130 13.5 99 6.2 .54Mobil Pegasus 805 Super 15W-40 29.5 -30 224 115 14.5 128 6.4 .52

Mobil Pegasus 905 is our latest technology SAE 40 natural gas engine oil designed to provide superior oxidation andthermal stability creating the opportunity to extend oil drain intervals and decrease oil consumption. Mobil Pegasus 905is made from the highest quality base oils and advanced additive technology to provide outstanding wear protection andhelp control deposit formation. Mobil Pegasus 905 is designed for use in Caterpillar, Jenbacker, Waukesha, and otherturbocharged, naturally aspirated, medium to high speed, four-cycle gas engines requiring a low-ash level product.



Mobil Pegasus 905 40 29.3 -21 247 125 13 97 6.2 .54


17

Mobil Pegasus Special 15W-40 is a high quality multigrade SAE 15W-40 ashless detergent natural gas engine oil. It isformulated with effective oxidation and corrosion inhibitors, antiwear agents and shear-stable VI improvers for multigradeperformance. The oil provides excellent dispersancy, good high-temperature detergency and stability, and effectiveprotection against corrosion. Low temperature starting capability when using Mobil Pegasus Special 15W-40 makes itparticularly suitable for two- and four-cycle engines in remote locations and for mainline stations that are shut down forlong periods in the winter, then started on short notice without warming the lube and coolant system.

Viscosity SAE Grav. Pour Flash cP at cSt at cSt at % Sulf.

Product Grade API °C °C 25°F 40°C 100°C V.I. TBN Ash

Mobil Pegasus Special 15W-40 15W-40 30.2 -36 236 24,700 104 13.5 132 2.5 0.07

Mobil Polyrex EM grease contains advanced polyurea thickener that has low noise characteristics, excellent mechanicalshear stability, water resistance, and long life. Mobil Polyrex EM performs well in the EMCOR rust test, even with 10%synthetic seawater, typically exhibiting no rust. Mobil Polyrex EM is used as a factory-fill grease by several electric motorbearing manufacturers because it maintains its consistency under high shear conditions. It has outstanding hightemperature stability as shown in the ASTM D 3336 High Temperature Grease Life test. High temperature stability leadsto long-life characteristics, highly recommended for sealed-for-life applications, like electric motors, and also for ball orlightly loaded roller bearings operating at high temperatures where low oil separation is important.

Viscosity NLGI Thickener Worked Drop Point cSt at cSt at

Product Grade Type 60X Structure °C (°F) 40°C 100°C Color

Polyrex EM 2 Polyurea 280 Smooth and Homogeneous 288 (550) 115 12.2 Blue

Mobil Polyrex EP2 contains proprietary EP additives that protect against wear and provide extreme-pressure protectionup to 350°F. Its 4-Ball Weld and High Temperature Grease Life test results are significantly better than most multi-purpose greases. Combined with its exceptional water resistance, these properties make Mobil Polyrex EP2 anexcellent choice for general industrial applications as well as equipment that is subjected to high temperatures, highloads, or is exposed to large amounts of water.

Viscosity NLGI Thickener Worked Drop Point cSt at cSt at

Product Grade Type 60X Structure °C (°F) 40°C 100°C Color

Polyrex EP2 2 Polyurea 280 Smooth and Homogenous 265 ( 509) 235 18.4 Green

Mobil Polyrex 372 is a heavy-duty, multipurpose, extreme pressure NLGI No. 2 ployurea grease with exceptional hightemperature, water resistance, and shear stable properties. Mobil Polyrex 372 contains a high viscosity base oil incombination with EP additives to provide exceptional performance in demanding slow-speed, heavily-loaded conditions.Mobil Polyrex 372 meets the demanding conditions of current industrial and off-highway equipment. The grease will notsupport combustion when impacted by sparks or slag that are common in hot rolling operations.

Base Oil ViscosityNLGI Penetration at Drop Point cST at Color

Product Grade Thickener 77°F Worked °C (°F) 40°C Visual

Mobil Polyrex 372 2 Polyurea 285 280 (536) 370 Green

Mobil Pyrogard 53 is a synthetic phosphate ester fire-resistant hydraulic fluid. Mobil Pyrogard 53 has excellentresistance to oxidation, foaming, and hydrolysis, and separates readily from water. Factory Mutual (FM) has approvedMobil Pyrogard 53 as a less-hazardous hydraulic fluid. Butyl, Viton, EPR or equivalent elastomers are compatible withMobil Pyrogard 53. Mobil Pyrogard 53 is not compatible with Buna-N, Neoprene, SBR or natural rubber.

Viscosity Spec. Pour Flash Fire cSt at cSt at Color

Product Grav. °F °F °F 40°C 100°C Visual V.I. TAN

Mobil Pyrogard 53 1.150 0 475 690 42 5.1 Blue 8 0.1


18

Mobil Pyrogard D is a premium-quality water-in-oil emulsion fire-resistant hydraulic fluid that fills the need for aneconomical fire-resistant hydraulic fluid in general industry, coal mines, and rolling mills. Mobil Pyrogard D has factoryMutual (FM) approval. Mobil Pyrogard D can withstand moderate exposure to temperatures below freezing withoutharm, but it is not recommended for continual low-temperature service. The water content of Mobil Pyrogard D must be38 percent or more to maintain fire-resistant properties.

Viscosity Spec. Pour Flash cSt at cSt at Color

Product Grav. °F °F 40°C 100°C Visual

Mobil Pyrogard D 0.925 -22 — 115 — White

Water content, wt. % 44

Mobil Rarus 427 oil was developed to handle the higher speeds and temperatures of modern single- and multistagereciprocating air compressors. It is formulated from a high-grade stock of narrow distillation range and contains speciallyselected additives to enhance lubricity, antiwear properties, and rust protection in cylinder and crankcase lubrication. Thislubricant is particularly recommended for units with a history of excess oil degradation deposits. Mobil Rarus 427 canhelp minimize valve carbon and crankcase sludge deposits, which should allow service and drain intervals to beextended. It can also be used as a dual-purpose crankcase and cylinder lubricant. It is recommended for compressorswith discharge temperatures up to 300°F. Mobil Rarus 427 can also be used in rotary screw compressors where an ISOVG 100 compressor oil is recommended.



Mobil Rarus 427 0.883 -12 264 105 11.6 104 100

Mobil Rarus 800 Series are synthetic diester air compressor lubricants. Mobil Rarus 824 and 826 were developed forrotary screw compressors. These oils provide extended oil, filter, and separator life well beyond conventional compressorlubricants because of their extraordinary resistance to oxidation. The higher-viscosity-grades Mobil Rarus 827 and 829are recommended for reciprocating compressors with high discharge temperatures. They help minimize depositformation, thereby extending ring, cylinder, and valve life. Large multistage units operating under severe conditions mayrequire special engineering considerations. These products have a broad application temperature range from -20°Fambient start-up to +400°F discharge air.



Mobil Rarus 824 0.906 -54 244 30 5.5 127 32Mobil Rarus 826 0.941 -43 246 66 7.5 63 68Mobil Rarus 827 0.957 -36 270 107 10.1 66 100Mobil Rarus 829 0.969 -40 270 158 13.2 70 150


19

Mobil Rarus SHC 1020 Series are rotary air compressor lubricants that combine synthesized hydrocarbon fluids withhighly effective additives which provide exceptional thermal and oxidation stability over a wide range of temperatures, andimproved water tolerance and protection against corrosion. Recommended for all rotary screw and vane air compressors.They are particularly effective in screw-type compressors having oil injection cooling with high final compressiontemperatures, or in compressors that tend to form varnish and system deposits. They are an excellent choice whenextended drain intervals are desired. Mobil Rarus SHC 1024 meets DIN 51506 VDL 32 standards; Mobil Rarus SHC1026 meets DIN 51506 VDL 68 standards.



Mobil Rarus SHC 1024 0.846 -39 245 32 5.7 127 32Mobil Rarus SHC 1025 0.849 -39 245 44 7.2 131 46Mobil Rarus SHC 1026 0.858 -39 246 67 10.1 136 68

Mobil SHC 500 Series are synthetic, super-stabilized, antiwear hydraulic fluids that are recommended for systems usinggear, piston or vane pumps operating at either high or low pressures or temperatures. Their naturally high VI and wax-free synthesized hydrocarbon base fluid provide the widest operating temperature range of any industrial hydraulic fluid.Available in three viscosity grades, Mobil SHC 524, 525 and 526 are particularly recommended for use in severe serviceand sealed-for-life systems where exceptional fluid performance is desired. They are approved in the Denison HF-0,Vickers V-104C and 35VQ25, and Sundstrand pump tests. Their 11-stage rating in the FZG Gear Test demonstrates ahigh level of protection against wear and scuffing.



Mobil SHC 524 0.850 -55 453 32 6.4 144 32Mobil SHC 525 0.850 -55 460 46 8.5 154 46Mobil SHC 526 0.852 -55 420 68 11.5 158 68

Mobil SHC 600 Series are synthetic gear and bearing lubricants. They are designed for use under severe conditionssuch as extremely high or low temperatures. Mobil SHC 600 Series combine synthesized hydrocarbon fluids withadditives that enhance their oxidation stability, corrosion protection, and protection against wear. They are recommendedfor use in industrial enclosed gear sets and in heavily loaded plain or rolling element bearings.



Mobil SHC 624 0.849 -54 240 32 6.3 148 32Mobil SHC 625 0.853 -48 252 48 7.9 135 46Mobil SHC 626 0.858 -48 236 20 10.9 146 68Mobil SHC 627 0.861 -42 248 99 13.9 143 100Mobil SHC 629 0.866 -45 228 143 18.3 144 150Mobil SHC 630 0.866 -39 235 216 25.2 152 220Mobil SHC 632 0.867 -39 450 326 38.6 169 320Mobil SHC 634 0.867 -42 462 430 48.5 173 460Mobil SHC 636 0.867 -42 436 664 62.8 165 680Mobil SHC 639 0.869 -15 470 933 79.5 164 1,000


20

Mobil SHC 800 Series gas turbine lubricants are made from synthesized hydrocarbon base oils and a combination ofadditives to provide superior rust protection, low-temperature fluidity, and high-temperature oxidation stability. They arerecommended as circulating oils for the lubrication of land-based gas turbines, particularly units under 3000 hp used asstandby power units, and in some types of total energy systems. Mobil SHC 824 is approved by Solar Turbines. MobilSHC 825 is approved for Cooper-Bessemer gas turbines.



Mobil SHC 824 0.833 <-54 248 32 5.9 135 32Mobil SHC 825 0.833 -45 248 44 7.9 145 46

Mobil SHC PM Series are synthetic paper machine oils for calender press and other circulating systems. Available inthree viscosity grades (220, 320, and 460), they are formulated to provide superior lubrication and “keep-clean”performance under operating temperatures beyond the capability of conventional paper machine oils.



Mobil SHC PM 220 0.864 -36 220 225 25.6 133 220Mobil SHC PM 320 0.866 -33 220 325 34.7 135 320Mobil SHC PM 460 0.868 -27 220 465 44.8 137 460

Mobil Synthetic Oven Lube 1090 is suitable for the lubrication of hot conveyor chains in drying ovens and tenter frames,at chain temperatures up to 260°C (500°F). Such equipment is used in the manufacture of fiber glass insulation,particleboard, plastic film, and textiles. Mobil Synthetic Oven Lube 1090 can be fed to the chain automatically or byhand. Compared to mineral oil and conventional chain lubricants, Mobil Synthetic Oven Lube 1090 reduces carbonbuildup and extends cleaning intervals. It does not contain silicone.

Viscosity Spec. Flash cSt at cSt at

Product Grav °C 40°C 100°C V.I.

Mobil Synthetic Oven Lube 1090 0.913 240 210 22 126

Mobil Synturion 6 is a synthetic barrier fluid specially formulated to meet the demanding lubrication and coolingrequirements of mechanical seals to maximize seal life. Mobil Synturion 6 has excellent thermal and oxidative stability,low viscosity to aid in reducing internal friction and efficient heat transfer properties. Mobil Synturion 6 meets USDArequirements for incidental food contact.

Viscosity . Pour Flash cSt at cSt at

Product Number Grav. °C °C 40°C 100°C V.I.

Mobil Synturion 6 0.799 -63 168 5.2 1.89 135


21

Mobil Vactra Oil Named Series oils are high-quality, general-purpose oils used for the lubrication of intermittently oiledbearings. This requires an oil that will adhere strongly to metallic surfaces and maintain effective lubrication even thoughonly an extremely thin film of oil is present. These oils also are used in low pressure hydraulic and circulation systems. Inaddition to film-strength additives, these oils contain an effective rust inhibitor.



Mobil Vactra Oil Light 0.870 -27 212 32 5.0 97 32Mobil Vactra Oil Medium 0.876 -24 242 46 6.7 97 46Mobil Vactra Oil Heavy Medium 0.881 -15 266 68 8.7 98 68Mobil Vactra Oil Heavy 0.887 -15 246 100 11.2 98 100Mobil Vactra Oil Extra Heavy 0.890 -9 280 150 14.6 96 150Mobil Vactra Oil BB 0.893 -6 288 220 18.8 95 220Mobil Vactra Oil AA 0.891 -9 286 320 23.9 95 320Mobil Vactra Oil HH 0.900 (21˚F) (564˚F) 460 30.1 95 460

Mobil Vactra Oil Numbered Series are lubricants for machine tool ways and slides. They provide good stick-slip frictioncharacteristics, adhesiveness, foam resistance, rust protection, metal wetting, and superior lubricity. Special chemistryprovides superior coolant separability and excellent protection against corrosion in the presence of aqueous-coolants.The adhesive, friction modifier, and lubricity additives help eliminate stick-slip and chatter under thin-film, boundarylubrication conditions. This allows smooth, uniform motion, even at low table speeds. The four lubricants in the series arerecommended for all combinations of cast iron, steel, and non-metallic way materials. Mobil Vactra Oil No. 1 is a dual-purpose hydraulic and way oil; Mobil Vactra Oil No. 2 is suitable for ways on small-to medium-size machine tools and forflood application in large machines; dual-purpose gear and way lubrication systems usually require Mobil Vactra Oil No. 3 and No. 4, with the latter recommended for large machines where way pressures are high or extreme precision is required.



Mobil Vactra Oil No. 1 0.870 -21 406 32 5.3 96 32Mobil Vactra Oil No. 2 0.880 -27 424 68 8.6 96 68Mobil Vactra Oil No. 3 0.890 16 446 150 15.0 96 150Mobil Vactra Oil No. 4 0.890 21 468 215 18.6 96 220

Mobil Vacuoline 100 Series oils are a family of high-quality, high-viscosity-index mineral oils designed to exceedMorgan Construction Company’s Morgoil Bearings Specification. In addition to their natural oxidation stability, they haveexcellent demulsibility and rust-resistant properties. These oils readily separate from solid contaminants for easy cleaningby settling, filtration, and centrifuging.



Mobil Vacuoline 133 0.892 16 550 220 18.8 95 220Mobil Vacuoline 137 0.898 16 547 320 23.9 95 320Mobil Vacuoline 146 0.902 20 565 460 30.0 95 460Mobil Vacuoline 148 0.908 20 604 680 36.7 95 680


22

Mobil Vacuoline 500 Series roll bearing oils are designed specifically for the lubrication of Morgan No-Twist Rod Mills.The Mobil Vacuoline 500 Series are also suitable for other primary mill and mini-mill bearing application systems. Inaddition to the qualities of the Mobil Vacuoline 100 Series, they have exceptional antirust demulsibility and antiscuffproperties. They have high-level builder support from Morgan Construction Company.



Mobil Vacuoline 525 0.887 -6 507 89 10.7 95 —Mobil Vacuoline 528 0.887 -6 521 150 14.6 95 150Mobil Vacuoline 533 0.898 0 543 220 19.2 95 220Mobil Vacuoline 537 0.898 10 550 325 24.0 95 320Mobil Vacuoline 546 0.898 5 546 460 30.0 95 460

Mobil Vacuoline Oil 1400 Series oils are used where machine tool ways are lubricated by bleeding oil from the hydraulicsystem. They possess the lubricity necessary to help eliminate chatter and stick-slip of tables under moderate loadconditions, while having sufficient chemical stability for service as a hydraulic fluid in noncritical systems.



Mobil Vacuoline Oil 1405 0.880 10 410 32 5.3 96 32Mobil Vacuoline Oil 1409 0.890 10 424 68 8.6 96 68Mobil Vacuoline Oil 1419 0.900 10 419 222 19.0 96 220

Mobil Vacuum Pump Oil is a high-quality, straight mineral oil with a narrow boiling range and a low vapor pressure. It isrecommended for use in most vacuum pumps where high vacuums, not possible to obtain with regular oils, are required.Because this is a dehydrated oil, containers should be kept well sealed to prevent contamination by moisture from anysource.



Mobil Vacuum Pump Oil* 0.881 -12 232 66 8.3 92 68

*Max Pressure (Welch Pump)—0.08 Microns of Mercury

Mobil Vaprotec Light is a three-phase rust-inhibiting circulation oil. It contains a thin-film rust inhibitor, a liquid-phaserust inhibitor, and a vapor-phase inhibitor in addition to an antioxidant and a defoamant. It can be used for short termapplications where a turbine-quality oil in the ISO 32 viscosity range is recommended during test, run-in and storage.



Mobil Vaprotec Light 0.875 -7 193 30 5.3 95 32


23

Mobil Velocite Oil Series are light-bodied, light-colored oils designed for the lubrication of very-high-speed spindles inmachine tools and textile machinery. They are specially compounded to give excellent resistance to wear, depositformation, and rust formation.



Mobil Velocite Oil No. 3 0.810 -27 183 2 — — 2Mobil Velocite Oil No. 4 0.822 5 216 4.8 1.5 — 5Mobil Velocite Oil No. 6 0.844 32 356 10 2.6 95 10Mobil Velocite Oil No. 8 0.858 27 381 15 3.0 85 15Mobil Velocite Oil No. 10 0.865 27 413 20 4.0 95 22

Mobilarma 200 Series rust preventives are light-bodied petroleum solvents with polar rust preventive, waterdisplacement and fingerprint neutralizing additives. Mobilarma 245 is suited for the protection of finely finished partsbetween machining operations, including operations where water-soluble cutting or grinding fluids have been used. It isalso suitable for use just before parts are packaged for storage or shipment, or to “dry” parts as a temporary protectionuntil a heavier duty rust preventive can be applied. Mobilarma 247 is the heavier and will give the longest rust protectionof any of the Mobilarma 200 Series solvent-based products.

ViscositySpec. Flash SUS at Color

Product Grav. °F 100°F Visual

Mobilarma 245 0.810 100 35Mobilarma 247 0.846 160 38 Brown

Mobilarma 500 Series rust preventive/lubricants combine excellent lubricating value with effective rust preventiveproperties. They meet the rust protection requirements for internal surfaces of all types of equipment including engines,compressors, circulation and hydraulic systems and splash-lubricated parts. They are particularly effective in protectingmachines while in transit or in temporary storage.


Product Grav. °F °F 40°C 100°C V.I.

Mobilarma 522 0.876 -10 360 27.0 4.8 95Mobilarma 524 0.884 0 425 88.0 10.2 95

Mobilarma 777 and 778 rust preventives were developed for cold-rolled sheet and coiled steel and will protect againstrust under extreme atmospheric conditions. They are nonsticky, oil base products that will not cause stains due tooxidation deposits.

ViscositySpec. Pour Flash SUS at cSt at

Product Grav. °F °F 100°F 40°C

Mobilarma 777 0.868 21 273 75 13.4Mobilarma 778 0.873 27 298 100 18.8


24

Mobilarma 798 is a film-forming rust preventive formulated to provide excellent protection against rust and corrosion onwire rope. Mobilarma 798 has an NLGI Grade 1 consistency and protects against the corrosive effects of both salt waterand fresh water over a wide temperature range. It resists throw-off in high speed service and adheres without being tackyor stringy.

Viscosity NLGI Drop Point SUS at cSt at Color

Product Grade °F, min 210°F 100°C Visual

Mobilarma 798 1 145 120 23.0 Amber; Semi-solid

Mobilfluid 350 is a premium-quality power transmission fluid designed for machine tool and industrial hydrostatic drivesand other industrial equipment drives using wet clutches. It has an extremely high viscosity index (VI), low pour point, andexcellent low-temperature viscosity characteristics. It resists the loss of viscosity and VI under severe mechanical shearand is highly resistant to foaming and air entrainment. Antiwear additives in Mobilfluid 350 are nonreactive and do notaffect the sintered bronze or other materials used as the facings of wet clutches in machine tool drives.


Product Grav. °F °F 40°C 100°C V.I.

Mobilfluid 350 0.887 -39 370 39.9 7.6 154

Mobilfluid 424 and Mobilfluid LT are high-performance, multipurpose tractor transmission and hydraulic fluids. Theyuse advanced technology for optimum performance in farm, contractor, and industrial tractors. Mobilfluid 424 isapproved against John Deere J20C, and recommended for agricultural applications requiring Allison C-4 and CaterpillarTO-2 fluids. Mobilfluid LT is approved against John Deere J20D and meets Caterpillar TO-2 requirements. They areapproved against Ford New Holland M2C134D, Massey Ferguson M1135 and M1141, White New Idea, Kubota, DenisonHF-0, HF-1 and HF-2 (424), and Sauer Sundstrand specifications. They are also recommended for use in CaseInternational, Deutz-Allis, Komatsu, Vickers, and Cincinnati Milacron equipment. Mobilfluid 424 and Mobilfluid LT arerecommended for top-up and refill of transmissions, final drives, hydraulics, power steering, wet brakes, PTOs, andhydrostatic drives. Mobilfluid LT is designed for use in equipment needing cold weather start up and operation qualities.Mobilfluid 424 and Mobilfluid LT are not to be used in passenger car automatic transmissions.

Viscosity Grav. Pour Flash cP at cP at cSt at cSt at

Product API °F °F -40°C -35°C 40°C 100°C V.I.

Mobilfluid 424 29.0 -42 442 — 55,000 55 9.3 152Mobilfluid LT 30.0 -54 381 18,000 — 34 7.2 180

Mobilgard 1 SHC is an SAE 40 (also meets SAE 20W-40 grade), high-performance, 15 TBN, fully synthetic lubricant formedium- and high-speed marine and industrial diesel engines. This oil provides excellent low-temperature fluidity,increased thermal and oxidative stability, and low volatility. Waste oil disposal costs can be minimized because this oilcontains no zinc and the low chlorine level is well below the most stringent regulations in effect today. Mobilgard 1 SHCmeets API CD, CF and CF-2 standards.

Viscosity Spec. Pour Flash cSt at cSt at % Sulf.

Product Grav. °C °C 40°C 100°C V.I. SAE TBN Ash

Mobilgard 1 SHC 0.872 -54 250 109 14.5 136 40 15 1.60


25

Mobilgard® M50 is a 50 TBN SAE 40 engine oil designed for use in all marine medium-speed diesel applications usingresidual fuel, especially the most severe low lube consumption engines used in marine propulsion, power generation andland based power generation applications. It provides excellent TBN retention, high temperature oxidation and thermalstability, low volatility, load carrying properties, and corrosion protection. This product is specifically designed to maintaina high level of engine cleanliness even at very high levels of residual fuel contamination in the lube oil. Mobilgard M50 isespecially recommended for use in the latest medium speed engines designed with “flame ring” cylinder liners operatingon high sulfur fuels.


Product Grav. °C °C 40°C 100°C SAE TBN Ash

Mobilgard M50 0.922 -6 228 142 14.0 40 50 6.5

Mobilgard 300 lubricant was developed specifically to satisfy the system oil requirements of current designs of high-output crosshead engines. It provides exceptional resistance to the formation of piston cooling space deposits while atthe same time supplying additional load-carrying ability, detergency for cleanliness, and alkalinity to neutralize corrosiveacids. Oil life is maximized by the exceptionally high stability and excellent water separating ability of this product.



Mobilgard 300 0.889 -12 226 111 12 97 30 5.0 0.73

Mobilgard 312, 412 and 512 moderately alkaline diesel oils were developed for industrial, marine, and railroad trunkpiston diesel engines using normal or economy fuels of less than 1.5 percent sulfur. The solvent-treated base stockshave been enhanced by alkaline detergent-dispersant additives and effective oxidation inhibitors. Their acid neutralizingability is indicated by their TBN of over 10. In the recommended range of service, these oils effectively combat piston andport deposits and help minimize piston ring and liner wear. Mobilgard 312, 412, and 512 meets the API CF testspecifications.



Mobilgard 312 0.896 -9 226 108 12.0 100 30 15 2.1Mobilgard 412 0.899 -9 272 142 14.5 100 40 15 2.1Mobilgard 512 0.894 -9 282 219 19.4 100 50 15 2.1

Mobilgard M30 and M40 Series are premium 30 TBN and 40 TBN engine oils designed for use in the most severeresidual-fueled medium-speed diesel applications. These diesel engine oils have been specially formulated to provideoutstanding residual fuel compatibility characteristics for excellent engine cleanliness, especially in crankcase, camshaftareas, ring belt, and piston under-crown. They provide excellent high temperature oxidation and thermal stability, lowvolatility, high load carrying properties, and corrosion protection.


Product Grav. °C °C 40°C 100°C SAE TBN Ash

Mobilgard M330 0.907 -6 244 112 12.0 30 30 3.8Mobilgard M430 0.907 -6 250 143 14.0 40 30 3.8Mobilgard M340 0.915 -6 240 113 12.0 30 40 5.0Mobilgard M440 0.915 -6 242 143 14.0 40 40 5.0


26

Mobilgard 450 NC zinc-free, chlorine-free marine diesel engine oil is formulated to lubricate high-output, turbocharged,medium-speed trunk diesels under severe conditions. This includes high idle conditions and fuel sulfur contents less than1.5 percent. This oil provides easier waste oil disposal and good environmental awareness due to its zinc and chlorinefree formulation. Mobilgard 450 NC is an LMOA Generation 4 diesel engine oil which exceeds API CD and CF-2qualification performance and has EMD’s approval.



Mobilgard 450 NC 0.897 -6 260 139 14.1 98 40 13 1.60

Mobilgard 570 has been developed for marine crosshead engines with increased power and fuel efficiency. It employsnew additives with substantially greater thermal stability and an optimum viscosity of 21 cSt at 100°C for best lubricantdistribution and film retention. Through new refining technology, this higher viscosity is attained with little or no brightstock. Unique technology at the 70 TBN alkalinity level in new generation Mobilgard 570 has demonstrated superior ringand liner protection and cleanliness under sustained operation with fuel sulfur levels from less than 0.5% up to 5.0%.Mobilgard 570 has a wide fuel sulfur level capability and provides an extended period between piston overhauls.


Product Grav. °C °C 40°C 100°C V.I. SAE TBN

Mobilgard 570 0.937 -9 256 229 21 104 50 70

Mobilgard ADL Series is a family of increased-dispersancy engine oils for high BMEP medium- and high-speed dieselengines operating on distillate and MDO fuels. These advanced diesel lubricants are available in both SAE 30 and 40grades to suit most marine engine viscosity requirements. A special balance of detergent and dispersant propertiesincreases the oils’ resistance to the formation of lacquer in severe service and assists in removing sludge and deposits.Using Mobilgard ADL Series oils helps avoid high oil consumption associated with cylinder liner lacquering, improveoverall engine cleanliness, and significantly reduce the number of engine overhauls. Superior load-carrying propertiesminimize piston ring and liner wear and make Mobilgard ADL Series lubricants suitable for marine gear applications.



Mobilgard ADL 30 0.900 -12 246 108 11.6 100 30 15 2.3Mobilgard ADL 40 0.901 -9 244 142 14.5 101 40 15 2.3


27

Mobilgear 600 Series oils are premium-quality, heavy-duty industrial gear oils for the lubrication of enclosed gear setsoperating under heavy or shock loads. They are formulated to provide rust and corrosion protection, enhanced oxidationstability and resistance to foaming. The sulfur-phosphorus extreme-pressure additives provide antiwear and friction-reducing characteristics and help minimize the temperature rise in heavily loaded gear sets. They satisfy the currentAmerican Gear Manufacturers Association (AGMA) specifications and performance requirements.

Viscosity Spec. Pour Flash cSt at cSt at AGMA ISO

Product Grav. °C °C 40°C 100°C V.I. No. VG

Mobilgear 626 0.887 -27 225 68 9.2 98 2 EP 68Mobilgear 627 0.892 -27 235 100 12.0 98 3 EP 100Mobilgear 629 0.892 -27 245 150 15.8 98 4 EP 150Mobilgear 630 0.895 -24 255 220 19.5 98 5 EP 220Mobilgear 632 0.897 -18 265 320 24.5 97 6 EP 320Mobilgear 634 0.910 -12 275 460 29.9 96 7 EP 460Mobilgear 636 0.919 -9 285 680 39.2 90 680

Mobilgear SHC 150, 220, 320, 460, and 680 oils are synthetic, heavy-duty industrial gear oils for the lubrication ofenclosed gear sets operating under severe temperature ranges and load. Depending on viscosity, five grades ofMobilgear SHC 150, 220, 320, 460, and 680 lubricants are recommended for all steel-on-steel enclosed gear drives inthe temperature range between -34°C (-30°F) minimum ambient temperature and 121°C (250°F) maximum operatingtemperature.



Mobilgear SHC 150 0.868 -45 222 150 19.5 150 150Mobilgear SHC 220 0.874 -36 232 220 26.0 150 220Mobilgear SHC 320 0.876 -33 238 320 35.0 155 320Mobilgear SHC 460 0.868 -27 245 460 46.0 155 460Mobilgear SHC 680 0.890 -27 256 680 62.0 160 680

Mobilgear SHC 1000, 1500, 3200, and 6800 oils are synthetic extra-heavy-duty industrial gear oils for the lubrication ofall kinds of enclosed gearing as well as plain and rolling element bearings. Generally, these oils are ideal for heavilyloaded, low-speed gears and bearings where boundary lubrication conditions may prevail. Mobilgear SHC 1000, 1500,3200, and 6800 extra-heavy-duty lubricants also can be used for certain open gear applications, but special engineeringconsideration may be required to select the most effective method of application. Mobilgear SHC 6800 is exclusivelyendorsed by EMD for use in DC traction motor drives and General Electric has given it exclusive approval against GEspec D50E25B. Mobilgear SHC 3200 is approved against GE spec D50E25C.



Mobilgear SHC 1000 0.871 -24 240 1,000 81 160 1,000Mobilgear SHC 1500 0.883 -18 240 1,500 106 160 1,500Mobilgear SHC 3200 0.888 -9 240 3,023 171 160 3,200Mobilgear SHC 6800 0.897 -6 240 8,100 350 170 6,800

Mobilgear SHC 22M and 46M oils are extra-heavy-duty synthetic gear oils for the lubrication of heavily loaded, low-speed gears where boundary lubrication conditions prevail and for open gear applications where asphaltic, diluent-containing lubricants have historically been used.



Mobilgear SHC 22M 0.890 6 240 22,000 700 180 22,000Mobilgear SHC 46M 0.924 15 240 46,000 1,375 180 46,000


28

Mobilgear SHC XMP 320 is synthetic gear oil that combines a synthetic hydrocarbon fluid with an advanced andbalanced additive package designed to provide protection against scuffing and an improved level of protection againstmicro pitting fatigue even under extreme conditions. It also provides outstanding rust and corrosion protection versusconventional gear oils and excellent compatibility with non-ferrous metals at elevated temperatures.



Mobilgear SHC XMP 320 0.860 -38 242 335 38.3 164 320

Mobilgrease 28 is a clay-thickened, synthetic hydrocarbon-base-fluid grease designed primarily for aviation applications.However, it has certain properties and performance characteristics that make it a desirable lubricant for special industrialapplications as well. Mobilgrease 28 is designed for plain and rolling bearings, splines, screws, worm gears and othermechanisms. It meets the requirements of U.S. Military Specification MIL-G-81322E Grease, General-Purpose, Aircraftand meets the requirements of U.S. Military Specification DOD-G-24508A (Navy) for shipboard auxiliary machinery. It isdesignated as U.S. military symbol WTR and NATO code G-395.


Product Grade Thickener Worked Structure °F 40°C 100°C Visual

Mobilgrease 28 1 1/2 Clay 295 Smooth/ 305 30 5.8 DarkButtery Red

Mobilgrease CM-L, CM-P, CM-S and CM-W are heavy-duty, unleaded contractor/mining greases. They have excellentwater resistance and extreme pressure (EP) capabilities. These greases have excellent adherence to all surfaces,ensuring outstanding lubrication. Mobilgrease CM-L and CM-P greases have a high-temperature, lithium complexthickener system and contain molybdenum disulfide (3%). Mobilgrease CM-S and CM-W have a lithium complexthickener system. All of the greases contain oils at the optimum viscosity to perform tough lubricating jobs found in thecontractor/mining industries. Mobilgrease CM-P and CM-S greases are recommended for highly loaded plain andantifriction bearings working in severe operating and weather conditions. Mobilgrease CM-P has an operatingtemperature range of -5°F to +350°F. They are especially suitable for hinge and bucket pins. Mobilgrease CM-L andCM-W are winter-grade products recommended for low-temperature applications that require improved pumpability.Mobilgrease CM-L has an operating temperature range of -20°F to +350°F.

Penetration Base Oil ViscosityNLGI at 77°F Drop Point cSt at cSt at Color %

Product Grade Thickener Worked Structure °C (°F), min 40°C 100°C Visual Moly

Mobilgrease CM-L 1 Lithium 325 Smooth/ 260 (500) 150 16 Gray 3Complex Tacky

Mobilgrease CM-P 2 Lithium 280 Smooth/ 260 (500) 320 22 Gray 3Complex Tacky

Mobilgrease CM-W 1 Lithium 325 Smooth/ 260 (500) 150 16 Orange —Complex Tacky

Mobilgrease CM-S 2 Lithium 280 Smooth/ 260 (500) 320 22 Orange —Complex Tacky


29

Mobilgrease EAL 100 Series greases are formulated with synthetic vegetable base oil for environmentally sensitiveapplications. The proprietary biodegradable base fluid provides excellent lubrication while exceeding U.S. andinternational standards for biodegradability and aquatic toxicity. The two greases in the series, Mobilgrease EAL 101and Mobilgrease EAL 102, are multipurpose products recommended for the lubrication of plain and rolling elementbearings in normal through heavy-duty industrial applications. They are particularly recommended where loads are highor shock loads are present, or where severe vibration is a problem. The Mobilgrease EAL series greases performsimiarly to AGMA CG-1 greases, and will provide suitable lubrication for most AGMA-Type CG-1 flexible couplings. Thegreases are acceptable for use at operating temperatures between -30°C (-22°F) and 120°C (248°F), consistent withstandard relubrication intervals. They have good water resistance characteristics, antirust and corrosion preventionproperties.

Penetration Base Oil ViscosityNLGI at 77°F Drop Point cSt at Color

Product Grade Thickener Worked Structure °C (°F) 40°C Visual

Mobilgrease EAL 101 1 Li 12-OH 325 Smooth 180 (356) 100 BrownMobilgrease EAL 102 2 Li 12-OH 280 Smooth 180 (356) 100 Brown

Mobilgrease FM Series are translucent, tan aluminum-complex-thickened food machine greases. They are formulated toreplace many conventional lithium and synthetic greases in moderate- and high-temperature applications in food plantsand sanitary equipment. They meet USDA H-1 standards and Title 21 CFR 178.3570 requirements for incidental contactwith food, and are registered with NSF.* The two grades are suitable for regular duty up to 250°F, will withstand routinewater immersion, and offer good low-temperature pumpability, superior antiwear protection, and good protection againstcorrosion.

Penetration NLGI at 77°F Drop Point Mineral Base Oil Color

Product Grade Thickener Worked Structure °C (°F), min ISO VG Visual

Mobilgrease FM 101 1 Al Complex 325 Smooth/Tacky 216 (420) 100 Clear AmberMobilgrease FM 102 2 Al Complex 280 Smooth/Tacky 216 (420) 100 Clear Amber

*Listed with NSF.

Mobilgrease HT Series are unleaded, lithium complex thickened high temperature steel mill greases. They contain high-viscosity base oils and additives to provide the outstanding water spray-off, wet churn, and wet roll performance andexcellent extreme pressure antiwear properties required in steel mill service. They shed mill water, continue to lubricate,and aid in forming a strong seal to resist water intrusion. When free water does enter a bearing, the greases maintainconsistency. These greases have outstanding high-temperature performance properties. They can also be used in centralgrease systems at moderate temperatures. Mobilgrease HTF provides fire retardancy for castor and hot strip milloperations.



Mobilgrease HTR 1/2 Lithium Complex 340 Tacky 260 (500) 320 16 BlackMobilgrease HTM 1 1/2 Lithium Complex 295 Tacky 260 (500) 460 18 BlackMobilgrease HTS 2 Lithium Complex 280 Tacky 260 (500) 680 25 BlackMobilgrease HTF 2 Lithium Complex 280 Tacky 190 (375) 680 25 Black


30

Mobilgrease Moly 50, 51, 52 and Moly 50 Arctic are 5% moly greases intended for the lubrication of off-highwayequipment. They are unleaded, lithium complex soap greases with superior extreme pressure and antiwear properties.These greases have excellent “staying power” under extreme operating conditions and have especially good water washout and spray off capabilities. Mobilgrease Moly 50 is recommended for use in central lubrication systems found onCaterpillar and other manufacturers’ off-highway equipment. Mobilgrease Moly 50 Arctic is recommended for use in off-highway equipment operating in temperatures down to -30˚C. The excellent low temperature mobility of this productmakes it well suited for central dispensing systems. Mobilgrease Moly 51 is recommended for chassis lubricationwherever better low temperature pumpability is required. Mobilgrease Moly 52 is recommended for all general purposechassis lubrication including plain bearings. Mobilgrease Moly greases are not recommended for the lubrication of highspeed U-joints.

Base OilPenetration Viscosity

NLGI at 77°F Drop Point cSt at Color %Product Grade Thickener Worked Structure °C (°F), min 40°C Visual Moly

Mobilgrease Moly 50 0 Lithium 370 Smooth/ 240 (464) 320 Gray 5.0Complex Tacky



Mobilgrease Moly 50 Arctic 0 Lithium 370 Smooth/ 230 (446) 100 Gray 5.0Complex Tacky

Mobilgrease XHP 222 and XHP 222 Special are a premium lithium complex, extreme pressure multiservice greasesused in a wide range of applications. They are formulated to provide excellent high temperature performance withexcellent adhesion, structural stability and resistance to water wash out. The greases offer excellent protection againstrust, corrosion and wear especially on axles, rings and bearings. Mobilgrease XHP 222 does not contain lead, chlorineor nitrite. Mobilgrease XHP 222 Special contains 0.75% molybdenum disulfide and is intended for those lube points withsliding and pivoting movements.

Base OilViscosity

NLGI Drop Point cSt at Color %Product Grade Thickener Structure °C (°F), min 40°C Visual Moly

Mobilgrease XHP 222 2 Lithium Smooth/ >260 (500) 220 Blue —complex adhesive

Mobilgrease XHP 222 Special 2 Lithium Smooth/ >260 (500) 220 Gray .75complex adhesive

Mobilgrease XTC is an extreme-pressure, unleaded, high temperature, lithium soap/polymer thickened flexible couplinggrease. It is made with very viscous oil to provide low bleed properties critical to modern AGMA type CG-2 high speedcouplings. Mobilgrease XTC is recommended for temperatures from -30°C to 120°C.

Penetration Base Oil ViscosityNLGI at 77°F Drop Point cSt at Color AGMA

Product Grade Thickener Worked Structure °C (°F) 40°C Visual CG1/CG2

Mobilgrease XTC 1 Lithium Complex/ 325 Tacky 215 (419) 680 Dark MeetsPolymer Brown


31

Mobilith AW Series are lithium-complex thickened multiservice greases. They are formulated with antiwear agents toprovide excellent service under severe operating conditions and in the presence of water. Mobilith AW 1, 2, and 3greases are recommended for the lubrication of bearings operating with heavy or shock loads, and at temperatures up to130°C (266°F). They are suitable for lubricating cams, ways, and other sliding elements. Other applications includevehicles and grease components in paper mills, where both water and high temperatures are encountered. Mobilith AW0 and 00 are softer, high-temperature greases recommended for grease application systems, gear lubrication, and whereextreme-cold-temperature pumpability is important.

Penetration Base Oil Viscosityat 77°F Drop Point cSt at Color

Product Grade Thickener Worked Structure °C (°F), min 40°C Visual

Mobilith AW 00 00 Lithium Complex 415 Smooth/Tacky — 110 GreenMobilith AW 0 0 Lithium Complex 370 Smooth/Tacky — 150 GreenMobilith AW 1 1 Lithium Complex 325 Smooth/Tacky 260 (500) 150 GreenMobilith AW 2 2 Lithium Complex 280 Smooth/Tacky 260 (500) 150 GreenMobilith AW 3 3 Lithium Complex 235 Smooth/Tacky 260 (500) 150 Green

Mobilith SHC 100 is a high-performance electric motor bearing grease which combines a synthetic base fluid with alithium complex thickener. The synthetic base oil allows for low-temperature pumpability and very low start/run torquevalues. Mobilith SHC 100 is not an extreme-pressure grease. Mobilith SHC 100, an NLGI Grade 2 grease, is formulatedwith an ISO 100 viscosity grade base oil. It satisfies the long service life and performance requirements of grease-lubricated rolling element bearings for most electric-motor manufacturers.



Mobilith SHC 100 2 Lithium Complex 280 Smooth 260 (500) 100 14.5 Red

Mobilith SHC 220, 221, 460, 007 and 1500 are high-performance, extreme-pressure, multiservice greases whichcombine a synthetic base fluid with a lithium complex thickener. Mobilith SHC 220, suited for long life performance, isrecommended for automotive and industrial applications which need a lubricant that can perform well at extremeoperational temperatures. Mobilith SHC 221 is similar to Mobilith SHC 220, but is an NLGI grade 1. Mobilith SHC 460,an NLGI Grade 1 1/2 grease, is recommended for industrial and automotive applications in both high and lowtemperatures. It will provide outstanding bearing protection under heavy loads at low to moderately high speeds, andwhere water is a factor. Mobilith SHC 460 has performed extremely well in steel mill and paper mill applications. It alsohas proven to be an exceptional severe-service automotive chassis grease. Mobilith SHC 007 is used for leakygearboxes subjected to high temperatures and also for on-highway trailer wheel-end bearings. Mobilith SHC 1500 is anNLGI Grade 1 grease with an exceptionally high viscosity synthetic base oil. It is intended for plain and rolling elementbearings operating at slow speeds, heavy loads and high temperatures.



Mobilith SHC 220 2 Lithium Complex 280 Smooth/Slight Tack260 (500) 220 23.8 RedMobilith SHC 221 1 Lithium Complex 325 Smooth/Slight Tack260 (500) 220 23.8 Lt. TanMobilith SHC 460 1 1/2 Lithium Complex 305 Smooth/Slight Tack260 (500) 460 46.5 RedMobilith SHC 007 00 Lithium Complex 415 Smooth/Tacky Semi-fluid 460 46.5 RedMobilith SHC 1500 1 Lithium Complex 325 Smooth/Tacky 260 (500) 1,500 110 Red


32

Mobilith SHC PM and Mobilith SHC PM 220 are high performance paper machine greases which combine a syntheticbase fluid with a lithium-complex/polymer thickener. The resistance to a change in consistency when contaminated withwater and superior protection against rust and corrosion make ideal greases for the wet end of the paper machine. Theyare ideal greases for the highly loaded, low- to moderate-speed press section roll bearings because of the high viscosityof its base oil and the effective antiwear/extreme-pressure protection these provide. The low evaporation rate andexcellent high-temperature oxidation stability of the synthetic base oil of Mobilith SHC PM and Mobilith SHC PM 220help maximize application intervals and bearing life in high-temperature felt roll and calender stack bearings. Thesegreases have a wide operating temperature range of -40°C to +177°C (-40°F to +350°F).

Penetration Base Oil Viscosity NLGI at 77°F Drop Point cSt at cSt at Color


Mobilith SHC PM 1 1/2 Lithium Complex/ 305 Smooth/Slight Tack 260 (500) 460 46.5 Light TanPolymer

Mobilith SHC PM 220 1 1/2 Lithium Complex/ 305 Smooth/Slight Tack 260 (500) 220 23.8 Light TanPolymer

Mobilmet Alpha, Sigma, Gamma and Omega are mineral oil-type active cutting oils that incorporate synthesizedadditive technology to control the build-up edge for improved surface finish and tool life. These oils are blended with abalanced selection of additives designed to provide a synergistic effect that helps maximize performance. TheseMobilmet oils are recommended for use with metals varying from tough and draggy alloys to hard and brittle ones. Theymay stain most nonferrous metals. Mobilmet Sigma and Gamma contain an antimist agent.

Viscosity Spec. Pour Flash SUS at cSt at Color Phos. Sulfur Sulfur Lubricity Cl

Product Grav. °F °F 100°F 40°C ASTM % Total % Act.,% Fat % %

Mobilmet Alpha 0.865 30 320 100 18 7.0 Nil 1.2 0.40 5.0 NilMobilmet Sigma 0.874 30 350 150 30 7.0 Nil 1.1 0.60 3.0 NilMobilmet Gamma 0.876 30 350 167 33 7.0 Nil 1.2 0.60 4.0 0.40Mobilmet Omega 0.896 30 350 220 43 7.0 Nil 2.6 0.90 12.0 1.60

Mobilmet Aqua Rho is a bio-resistant emulsifiable metal working fluid. Mobilmet Aqua Rho, when mixed with waterforms an effective metal working coolant for a wide range of ferrous and non-ferrous alloys. Mobilmet Aqua Rho’scomponents are inherently bio-resistant and does not require the use of toxic biocides and/or fungicides. Mobilmet AquaRho does not contain biocides, chlorine, sulfur or phenols.

Viscosity Spec. Pour Flash cSt at cSt at Emulsion

Product Grav. °C (°F) °C (°F) 100°C 40°C ph (6% corrosion)

Mobilmet Aqua Rho 0.934 -29 (-20) 114 (237) 13 131 8.5

The Mobilmet CCF Series metal removal fluids are clear, non-chlorinated mineral oil based active cutting oils. Theycontain an innovative and particularly effective additive combination to meet the highest demands of machiningoperations, cutting conditions and tool and workpiece metallurgy. The antimist agent reduces oil consumption andworkplace mist. The fluids are clear allowing for better visibility of the workpiece.

Viscosity Spec. Pour Flash SUS at cSt at Color Sulfur Sulfur Friction Cl

Product Grav. °F °F 100°F 40°C ASTM Total % Act.,% Modifier % Antimist

Mobilmet Delta CCF 0.863 5 350 66 12.0 2.0 2.5 2.0 2.0 Nil NoMobilmet Lambda CCF 0.887 -22 378 97 19.9 2.0 2.5 2.0 2.0 Nil YesMobilmet Beta CCF 0.887 -5 350 141 30.0 2.0 2.5 2.0 2.0 Nil YesMobilmet Theta CCF 0.887 -5 350 159 34.0 2.0 2.5 2.0 2.0 Nil YesMobilmet Kappa CCF 0.887 -5 350 195 42.0 2.0 2.5 2.0 2.0 Nil Yes


33

Mobilmet Upsilon, Omicron, Omicron HD and Nu are mineral-oil-type, nonstaining cutting oils. They contain abalanced selection of additives that maximize performance. They meet the antiweld and lubricity requirements of themost severe machining operations on the most difficult-to-machine metals such as copper and its alloys. The nonstainingnature of these oils permit their use where complementary oils are required for the splash, hydraulic or spindle lubricationsystems of metalworking machines. Mobilmet Omicron, Omicron HD, and Nu contain an antimist agent.

Viscosity Spec. Pour Flash SUS at cSt at Color Phos. Sulfur Sulfur Lubricity Cl

Product Grav. °F °F 100°F 40°C ASTM % Total % Act.,% Fat % %

Mobilmet Upsilon 0.850 25 325 60 10 4.5 Nil 0.35 Nil 2.0 NilMobilmet Omicron 0.850 30 365 135 26 5.0 Nil 0.50 Nil 2.0 NilMobilmet Omicron HD 0.866 30 365 160 31 5.5 Nil 0.5 Nil 2.0 NilMobilmet Nu 0.884 10 360 195 37 8.0 Nil 1.1 Nil 8.0 0.8

Mobilmet 100 Series are general purpose, water soluble cutting oils. They will not stain and are suitable for both ferrousand nonferrous metals. Mobilmet S-122 is used in areas of normal (300 ppm) water hardness, while MobilmetS-126 offers good stability where water hardness exceeds 500 ppm. These oils are recommended for use in cutting andgrinding operations, particularly where enhanced cooling is needed.

ViscosityDensity Pour Flash cSt at Color Emulsion Freeze

Product Lbs/Gal °C (°F) °C (°F) 40°C ASTM Test Test

Mobilmet S-122 7.83 -18 (0) 177 (350) 49.0 8.0 Pass PassMobilmet S-126 7.40 -23 (-10) 122 (250) 54.0 4.5 Pass Pass

Mobilmet TC 30 is a mineral oil type cutting fluid specially formulated for thread cutting operations. Mobilmet TC 30balanced additive package provides enough lubricity and extreme pressure protection for even difficult to machine alloys.

ViscosityPour Flash cSt at Sulfur Sulfur Cl Lubricity

Product Density °C (°F) °C (°F) 40°C Active Total % % Fat %

Mobilmet TC 30 7.3 -3 (27) 160 (320) 28 1.0 2.7 .3 12

Mobiltac 325 NC and 375 NC lubricants are unleaded, diluent-type, heavy bodied lubricants designed to lubricate opengears on contractor, mining and industrial equipment. They contain a nonchlorinated, volatile solvent that ensures fluidityduring application, even at temperatures as low as -34°C (-30°F). Once applied, the diluent evaporates and the lubricantstake on a flexible, adhesive, high-strength consistency which is maintained throughout their service life. These new-generation lubricants are applied easily by hand or with automatic dispensers. Mobiltac 375 NC is also available as GearLube 375 NC Spray Can. This convenient package is for easy application in hard to reach areas.

Viscosity Spec. Flash cSt at cSt at Color

Product Grav. °C 40°C 100°C Visual

Mobiltac 325 NC 0.960 110 1,600* 1,000 BlackMobiltac 375 NC 0.960 135 5,000* 1,260 BlackGear Lube 375 NC Spray Can 0.960 — 5,000* 1,100

*Contains Diluent


34

Mobiltac LL, MM and QQ are nondiluent, high-viscosity open gear lubricants. They are formulated with toxicologicallysafe base stocks and additives. Mobiltac QQ meets the former AGMA 13 EP gear lubricants specification.


Product Grav. °C °C 40°C 100°C Visual

Mobiltac LL 0.916 -9 182 1,209 58 BlackMobiltac MM 0.934 3 182 3,900 126 BlackMobiltac QQ 0.940 6 190 9,526 217 Black

Mobiltemp 2 is a clay-thickened grease for sleeve and antifriction bearings operating at low speed and hightemperatures. It utilizes a high quality, high viscosity mineral oil and is specially formulated to provide low volatility andexcellent resistance to oxidation at high temperatures, resistance to water or steam contamination and good anti-wearperformance. Mobiltemp 2 is particularly suited for high temperature applications, resisting changes in consistency underboth high temperature and cyclic conditions of heating and cooling. The grease will not soften and leak under hightemperature conditions or harden excessively on cooling. The recommened operating temperature range is -29°C to+177°C (-20°F to +350°F), with even higher temperatures for short periods, with appropriate relubrication intervals. It isrecommeneded for use in oven conveyor chain bearings, kiln car wheel bearings, and glass manufacture conveer beltroller bearings.



Mobiltemp 2 22 Nonsoap 280 Smooth 300 (570) 460 31 Amber

Mobiltemp 78 is a clay-thickened grease for sleeve and antifriction bearings subjected to high temperatures and heavyloads. This grease has an operating temperature range of -29°C to +177°C (-20°F to +350°F). Mobiltemp 78 containsmolybdenum disulfide (1%) which imparts “staying power” in those situations where the grease itself has been depleted inuse and where only the molybdenum disulfide remains to prevent wear until more grease is applied. This grease hasshown outstanding ability to lubricate such components as conveyor bearings on high-temperature ceramic and paint-baking ovens and antifriction bearings on preconditioning drums of paper corrugators.

Penetration Base Oil Viscosity NLGI at 77°F Drop Point cSt at cSt at Color %

Product Grade Thickener Worked Structure °C (°F) 40°C 100°C Visual Moly

Mobiltemp 78 1 Nonsoap 325 Smooth 260 (500) 460 31 Gray 1.0

Mobiltemp SHC 32 is a clay-thickened, synthetic, multiservice grease. The synthetic hydrocarbon base fluid providesextremely low cold-temperature breakaway and running torque values, and maintains consistency over a wide operatingrange. In addition, it provides long service life due to superior resistance to oxidation. Mobiltemp SHC 32 exhibitsextreme-pressure characteristics. It is recommended for the lubrication of plain and rolling element bearings, splines,screws, and some enclosed gearing with temperature ranges from -54°C to 177°C (-65°F to 350°F).



Mobiltemp SHC 32 1 1/2 Nonsoap 310 Smooth 232 (450) 32 5.2 Dark Red


35

Mobiltherm 603 and 605 are mineral-type heat transfer oils intended for use in closed cold-oil-sealed systems.Mobiltherm 603 is a high-VI paraffinic oil that is safe to use up to 288°C (550°F) and where minimum shutdowntemperatures are not below -4°C (25°F). With its high specific heat and thermal conductivity at all temperaturesMobiltherm 603 provides rapid heating and greater flexibility in a system. It is particularly applicable where high heat-transfer rates or high flow rates at reasonably low temperatures are desired. Mobiltherm 605, using select petroleumcomponents, is intended for use in heat transfer systems where bulk temperatures can approach and equal 315°C(600°F).


Product Grav. °C (°F) °C (°F) 40°C 100°C

Mobiltherm 603 0.860 -4 (25) 171 (340) 20.4 4.0Mobiltherm 605 0.872 -12 (10) 198 (388) 30.0 5.0

Mobiltrans AST is an all-season, semi-synthetic, multigrade viscosity off-highway transmission fluid that is formulated toprovide optimum low temperature performance in cold-climate conditions while maintaining superior lubrication and filmthickness during high temperature operation. This high level of performance is achieved through the use of syntheticcomponents and a balanced additive package. Mobiltrans AST provides outstanding oxidation resistance, shearstability, clutch-plate friction, elastomer compatibility, and antiwear protection in transmissions operating under both highand low temperature conditions. It meets the Caterpillar TO-4 and TO-4M specifications and can be recommended inapplications requiring an Allison C-4 fluid. Mobiltrans AST is designed for use in off-highway transmissions. This productis recommended for use in Caterpillar, Case, Komatsu and other contractor, logging, mining, and farm equipmentapplications.

Viscosity Grav. Pour Flash cP at cP at cSt at


Mobiltrans AST 29.2 -38 432 9,400 107 14.2 134

Mobiltrans HD oils are latest-technology products designed to optimize performance of off-highway transmissions, drivetrains, and hydraulic systems without the compromises inherent in the mixed-fleet engine oils previously used in theseapplications. The new lubricants contain a balanced additive package which provides outstanding oxidation stability,clutch-plate friction, elastomer compatibility, and antiwear protection in gearboxes. The three grades, SAE 10W, 30, and50, are designed to optimize shear stability and provide excellent high-temperature/high-shear viscosity. Mobiltrans HDlubricants meet the Caterpillar TO-4 specification which cannot be fully satisfied by modern engine oils. They provideoptimum balance between static and dynamic friction in six clutch materials used in powershift transmissions, drive-trainclutches, steering clutches, and wet brakes. They also minimize chatter in oil-cooled disc brakes, and optimize durabilityfor extended service. Mobiltrans HD lubricants also provide excellent antiwear performance in powershift transmissions,gearboxes, and final drives. They provide outstanding FZG gear wear control, Vickers 35VQ25 pump protection inhydraulic systems, Allison C-4 performance, and API GL-3 EP gear score control. They are recommended for Caterpillar,Case, Komatsu, and other contractor, logging, mining, and farm equipment.


Product API °F °F 40°C 100°C TBN V.I.

Mobiltrans HD 10W 27.9 -27 396 42 6.3 7.9 96Mobiltrans HD 30 27.0 0 435 100 11.2 7.9 97Mobiltrans HD 50 24.7 5 464 195 18.0 7.9 101


36

Mobiltrans SHC 50 is a heavy-duty SAE 50 synthetic transmission oil. It is recommended for year-round lubrication ofautomotive manual transmissions in light-duty to extremely heavy-duty on- and off-highway equipment. This includessubzero conditions in arctic climates and operations requiring lubricants with relatively high viscosity and good load-carrying ability. Mobiltrans SHC 50 meets API Service GL-4, GL-3, MT-1. Mobiltrans SHC 50 meets and has beenapproved against the following equipment builders’ standards: Eaton Roadranger E500 (PS-164), Mack TO-A Plus,Meritor Extended Drain (O-81), and Volvo STD 97305. It is approved for use at 500,000-mile drain intervals by Eaton,Mack Trucks and Meritor providing 750,000-mile warranty protection. It is NOT suitable for hypoid gears or otherapplications where API GL-5 or MIL-PRF-2105E multipurpose lubricants are specified. Mobiltrans SHC 50 has the sameviscosity as most SAE 50 engine oils and SAE 90 gear lubricants at the high end of the temperature-viscosity scale.However, because of its inherently higher viscosity index, it provides a better protective film at higher temperatures thanconventional oils, without the addition of VI improvers. Hence, the product is shear-stable under all operating conditionsand it offers an extremely low pour point. It remains fluid without channeling at subzero temperatures. Mobiltrans SHC50 gives excellent FZG gear protection in stages 1 through 11. It also provides outstanding CRC L-60 gear oxidation andthermal breakdown deposit protection. (At the time of this printing Mobiltrans SHC 50 was well positioned to be approvedagainst Eaton’s new HD500K specification. Please refer to the current product data sheet.)



Mobiltrans SHC 50 30.0 -54 464 140 17.6 138

Mobiltrans SHC Arctic is an all temperature, fully synthetic transmission oil designed especially for extreme cold climateapplications. It provides outstanding clutch and brake compatibility along with high and low temperature performance onlypossible with synthetics. Mobiltrans SHC Arctic meets the Caterpillar TO-4 specification and is also recommended forapplications requiring an Allison C-4 fluid. This product is very shear stable and contains no viscosity modifier.Mobiltrans SHC Arctic provides excellent clutch and transmission life, and can be recommended for use in Caterpillar,Case, Komatsu, and other off-highway equipment where Caterpillar TO-4 or Allison C-4 fluids are required.

Viscosity Grav. Pour Flash Brookfield cP at cSt at cSt at


Mobiltrans SHC Arctic 33.9 -60 401 42,000 81.3 12.2 146

Mobilube HD 80W-140 is an extreme-pressure gear lubricant made with specially processed base oils. It is specificallyformulated with a wide-range viscosity grade for good high and low temperature performance and protection. MobilubeHD 80W-140 meets API Service GL-5. This product can be used for initial fill, topping-off and refill of enclosed automotivegears for manual transmissions, gear cases of semi-automatic transmissions where gear lubes are recommended, driveaxles and final drives of passenger cars, trucks, taxicabs, and contractor and farm equipment. It should not be used inapplications where automatic transmission fluid or engine oil is recommended.

Viscosity Grav. Pour Flash Brookfield cSt at cSt at

Product API °F °F cP at -40°C 40°C 100°C V.I.

Mobilube HD 80W-140 27.5 -33 352 143,000 259 26.6 133


37

Mobilube HD LS 80W-90 is a multipurpose, heavy-duty, extreme pressure lubricant designed specifically for limited-slipdifferentials. It is made with specially processed base oils that provide good stability at high temperatures and goodprotection at low temperatures. Mobilube HD LS 80W-90 meets API Service GL-5, and can be used for topping-off andrefill of limited-slip, final drives of passenger cars, trucks, taxicabs, and contractor and farm equipment. It should not beused in applications where engine oil or automatic transmission fluid is recommended.


Product API °F °F cP at -26°C 40°C 100°C V.I.

Mobilube HD LS 80W-90 26.5 -22 446 130,000 141 14.8 105

Mobilube HD Plus multipurpose, heavy-duty, extreme-pressure gear lubricants are recommended for enclosed gearcases on passenger cars, trucks, taxicabs and contractor and farm equipment. They are available in two multiviscositygrades: SAE 80W-90 and SAE 85W-140. Mobilube HD Plus 80W-90 and Mobilube HD Plus 85W-140 meet APIService GL-5, MT-1 and are approved against the Mack GO-J specification. Mobilube HD Plus gear lubricants areintended for initial fill, top-off and refill of hypoid and other drive axles, power dividers and final drives. These gearlubricants are ideal for equipment operated under high-speed shock-load, high speed low-torque, and low-speed high-torque conditions. An enhanced additive system improves their thermal stability at high temperatures, reduces carbondeposits, and provides better seal protection. Mobilube HD Plus gear lubricants have excellent antiwear properties, asshown by their performance in the full-scale L-37 and L-42 axle tests. They guard against rust and corrosion resultingfrom water contamination or storage in a humid atmosphere as demonstrated by passing the L-33 rust test.


Product API °F °F cP at °C 40°C 100°C V.I.

Mobilube HD Plus 80W-90 26.4 -17 403 110,000 @ -26 141 14.5 102Mobilube HD Plus 85W-140 24.8 5 446 46,000 @ -12 345 25.7 98

Mobilube SHC multipurpose synthetic gear lubricants are recommended for the year-round lubrication of enclosedautomotive gear drives, including subzero conditions and where operations require lubricants with relatively high viscosityand excellent load-carrying ability. They are available in two multiviscosity grades: Mobilube SHC 75W-90 (SAE 75W-90)and Mobilube SHC 80W-140 (SAE 80W-140). Mobilube SHC products meet API Service GL-5, MT-1. Mobilube SHCproducts meet the following equipment builders’ standards: Eaton Roadranger E500 SHAES-256 (formerly PS-163);Mack GO-J Plus (75W-90 only), GO-J; Meritor O-76N (75W-90 only), O-80. Mobilube SHC gear lubricants aremanufactured from synthesized hydrocarbon base oils and a stable sulfur-phosphorous additive package which improvestheir thermal stability at high temperatures, reduces carbon deposits, and provides better seal protection. They providethe viscosity-temperature characteristics necessary for products having wide temperature applications, without theaddition of VI improvers. These completely shear-stable lubricants are suitable for topping-off or refilling hypoid and otherdrive axles, final drives, manual transmissions, power dividers, transfer cases, and other heavy-duty gear applications. Inmost on-highway applications, Mobilube SHC can provide a fuel economy advantage of up to three percent overcomparable conventional mineral gear lubricants.



Mobilube SHC 75W-90 33.8 -55 401 120 15.9 140Mobilube SHC 80W-140 31.2 -44 450 310 31.2 139


38

Mobilube XFD (extreme final drive oil) has been specifically formulated to provide optimum component life for final drivesand differentials operating under heavy loads and/or in high ambient temperatures. These products provide outstandingbearing and gear protection, beyond that of TO-4 fluids, to help prevent premature failure due to fatigue. Mobilube XFDis available in SAE 50 (maximum operating ambient temperature of 90°F) and SAE 60 (maximum operating ambienttemperature of 122°F). These products are not recommended for engines, transmissions, hydraulic systems or in finaldrives and axles containing friction materials and/or wet brakes.

Viscosity Grav. Pour Flash Brookfield, cP cSt at cSt at

Product API °F °F at °C 40°C 100°C V.I.

Mobilube XFD 50 26.2 -11 482 75,000 @ -15 206 18.4 98Mobilube XFD 60 25.9 5 491 75,000 @ -10 334 25.2 97

Mobilux EP 023 is a semifluid, extreme pressure, lithium thickened grease for the lubrication of gears in leakygearboxes. The grease contains antiwear additives and rust and corrosion inhibitors. Specific applications also includegearboxes, cutter heads, trams, oscillating arms, pots or gathering head drives, pump cases, and chain cases. It isrecommended for use from -15°C to 120°C.

Base Oil ViscosityNLGI Drop Point cSt at cSt at Color

Product Grade Thickener Structure °C (°F) 40°C 100°C Visual

Mobilux EP 023 000 Li 12-OH Semifluid — 320 25 Medium Brown

Mobilux EP 111 is extreme pressure, lithium thickened, molybdenum (oil-soluble) fortified, high viscosity flexible couplinggrease. Mobilux EP 111 resists centrifugal separation of oil from the soap at high rotating speeds. This grease isparticularly well-suited for the lubrication of heavily loaded gear couplings up to 2000 rpm and between -7°C and 121°C(20°F and 250°F).

Penetration Base Oil ViscosityNLGI at 77°F Drop Point cSt at cSt at Color AGMA

Product Grade Thickener Worked Structure °C (°F) 40°C 100°C Visual CG1/CG3

Mobilux EP 111 1 Li 12-OH 325 Smooth/Tacky 180 (356) 800 45 Black Meets


39

Mobilux EP Series are extreme pressure, lithium thickened, multipurpose greases to lubricate both rolling element andplain bearings, under wet and dry conditions. Their smooth texture and excellent low-temperature pumping characteristicsmake the Mobilux EP 0 and Mobilux EP 1 products ideal for central dispensing systems and general use from -29°C to121°C (-20°F to 250°F). Their superior resistance to oxidation is combined with the ability to protect against corrosion ofcopper alloys and the rusting of steel, even in the presence of alkaline water. Mobilux EP 2 is useful from -20°C to130°C.



Mobilux EP 0 0 Li 12-OH 370 Smooth 190 (374) 150 14 AmberMobilux EP 1 1 Li 12-OH 325 Smooth 190 (374) 150 14 AmberMobilux EP 2 2 Li 12-OH 280 Smooth 190 (374) 150 14 Amber

Nyvac FR 200D Fluid is a water glycol fire-resistant hydraulic fluid. It provides excellent protection against rust in both theliquid and vapor phases. Its foam-resistance, low-temperature flow characteristics, and storage stability are also excellent.It contains diethylene glycol. Nyvac FR 200D Fluid has no deteriorating effect on synthetic or natural rubber packing orseal materials and is fully compatible with competitive water glycol fluids. It is approved by Factory Mutual (FM).

Viscosity Spec. Pour cSt at cSt at Color

Product Grav. °F 40°C 100°C Visual V.I.

Nyvac FR 200D Fluid 1.080 -22 42 8.4 Red 175

Water content, wt. % 43

Quaker Quintolubric 822/888 is a family of synthetic fire-resistant hydraulic fluids that contain no water, petroleum oils,chlorinated hydrocarbons or phosphate esters. These products should be used in those hydraulic applications wheretrouble-free fluids with a high degree of lubricity and fire resistance are required.

Flash Viscosity Spec. Pour COC Fire Point cSt at cSt at ISO Color

Product Grav. at 77°F °C (°F) °C (°F) °C (°F) 40°C 100°C V.I. VG Visual

Quaker Quintolubric 888-46 0.900 <-20 (<-4) 275 (527) 325 (617) 46 10 220 46 Light Amber Quaker Quintolubric 888-68 0.910 <-20 (<-4) 275 (527) 326 (617) 68 14 215 68 Light AmberQuaker Quintolubric 822/450 0.922 <-26 (-15) >260 (500) >288 (550) 100 14.2 145 100 Light Amber


40

Quaker Quintolubric 822-EHC is 100% active, synthetic polyol ester fire resistant hydraulic fluid. This product isdesigned to replace phosphate ester based fluids used in electrohydraulic control systems.

Flash Viscosity Spec. Grav. Pour COC Fire Point cSt at cSt at

Product at 60°F °C (°F) °C (°F) °C (°F) 40°C 100°C V.I.

Quaker Quintolubric 822-EHC 0.910 <-26 (-15) >260 (500) >288 (550) 47 8.9 >140

Socony Oven Conveyor Lubricant was developed for the lubrication of oven conveyor chains up to 204°C (400°F). Itconsists of a light oil that carries colloidal graphite between moving parts. The carrier oil is sufficiently volatile toevaporate at the temperatures involved without leaving residues that might cause sticking.


Product Grav. °C °C 40°C 100°C Visual

Socony Oven Conveyor Lubricant 0.854 -1 129 13 3.7 Black

Thermrex Series are mineral quenching oils for the heat treatment of al loy steels. ThermrexR-21 is a mineral oil blend carefully selected to approximate ISO VG 22 and yield consistent Relative Cooling Indices(RCI) from 95 to 160. Thermrex F-43 is a fast quench oil augmenting selected base stocks with additive technology toyield an RCI of 195.

ViscositySpec. Pour Flash cSt at Quench Cooling Rate

Product Grav. °F °F 40°C RCI % Time,Sec.ASTM D 6200, F/Sec.

Thermrex R-21 0.867 35 342 25.7 120/130 23 112Thermrex V-32 0.856 25 349 16.0 148/162 19 116Thermrex F-43 0.864 20 324 20.0 185/200 15 160

Vacmul A6 and 2105 are flute grinding cutting oils. These transparent oils reduce abrasive tool wear and provideimproved surface finish. They effectively remove heat generated by cutting or grinding. Vacmul A6 is a light-duty cuttingoil designed for applications such as flute grinding. Vacmul 2105 is recommended as a drill flute grinding oil and for allarduous form grinding operations. It helps prevent overheating, distortion and dimensional inaccuracies when grinding atfast rates.

ViscositySpec. Flash cSt at Color Phos. Lubricity, Sulfur, Cl

Product Grav. °C 40°C ASTM % Fat % Total % %

Vacmul A6 0.876 202 25 6 0.1 3.0 0.3 0.2Vacmul 2105 0.872 204 29 2 0.1 5.0 — 0.5


41

Vacmul 280 and 281 are economical medium-duty, non-staining cutting oils for screw machine applications. Vacmul 281contains an antimist additive. Both products can be used on the lube side and the cutting side of the equipment.

Viscosity Density Pour Flash cSt at Color Lubricity, Sulfur, Cl Anti-

Product Lbs/Gal °C (°F) °C (°F) 40°C ASTM Fat % Total % % mist

Vacmul 280 7.31 -6 (21) 196 (385) 28.5 4 1.5 0.3 1.4 NoVacmul 281 7.31 -6 (21) 196 (385) 34 5 1.5 0.3 1.4 Yes

Vacmul 3 A is a low-viscosity mineral oil intended for use as an EDM fluid or as a light-to-moderate-duty honing oil.Vacmul 3 D is a medium-duty, mineral-oil-based honing and grinding fluid. Vacmul 0 3 D is a medium-to-heavy-dutymineral oil based honing and grinding fluid. Vacmul 30 A 20 is a drawing oil for use as a wire drawing oil for non-ferrousmetals such as aluminum and copper. It possesses a high degree of lubricity. It is designed for operations where moredifficult-to-machine metals are used. It performs well on both ferrous and nonferrous metals. Vacmul 3 A, 3 D, 0 3 D and30 A 20 are non-staining.

Viscosity Spec. Pour Flash cSt at Color Dielectric Lubricity, Sulfur Cl

Product Grav. °C (°F) °C (°F) 40°C ASTM Strength Fat % Total % %

Vacmul 3 A 0.835 -1 (+30) 127 (260) 4.3 1.5 28 Nil Nil NilVacmul 3 D 0.840 0 (32) 118 (245) 6.2 8.0 — 5.5 0.7 0.7Vacmul 0 3 D 0.847 126 6 6.2 — 8.0 1.01 NilVacmul 30 A 20 0.902 (25) (450) 23.2 — 17.0 Nil Nil

Vacsul 18 F is a heavy-duty cutting oil for difficult machining operations such as broaching.

ViscositySpec. Flash cSt at Color

Product Grav. °C 40°C ASTM

Vacsul 18 F 0.898 194 33

Whiterex 425 is a highly refined mineral white oil. It has been specially treated so that color bodies have been removedso that it will not stain or discolor material with which it comes in contact. Whiterex 425 is qualified under USDARegulation H-1 as suitable for use where there is a likelihood of incidental food contact. It may be used, therefore, in foodprocessing plants or other applications where such contact with food is possible.

Viscosity Spec. Pour Flash cSt at cSt at Color ISO

Product Grav. °F °F 40°C 100°C Visual V.I. VG

Whiterex 425 0.877 -5 400 53 7.0 White 60 68


42


AT

1 (800) 662-4525



HEALTH AND SAFETY PRECAUTIONS

43

The health and safety of people who handle and use Mobil products are of vital interest andconcern to us. Most Mobil products are regarded as generally safe. As with all petroleumproducts, however, excessive and prolonged contact or improper handling may result in adverseeffects. Below are general health and safety precautions for handling petroleum products. Formore details and product-specific information, we urge you to obtain and read carefully theMaterial Safety Data Sheet (MSDS) for each Mobil product handled to ensure that employeesand users fully understand appropriate precautionary information relating to safe use. (See thediscussion of Material Safety Data Sheets on page 46.) Material Safety Data Sheets for Mobilproducts are available on the web at http://emmsds.ihspsl.com, by calling Fax-on-Demand at1-613-228-1467, by calling the MSDS Order Desk at 1-856-224-4644, or by contacting your localMobil representative.

ExxonMobil 24-Hour Emergency Line (Call Collect): 1-609-737-4411 in the U.S.

FIRE HAZARDS

Many petroleum products are highly volatile and flammable and must be handled with extremecaution to prevent fire or explosion. These include a few extra light viscosity lubricants and manysolvents. The federal Occupational Safety and Health Administration (OSHA) has classifiedproducts with flash points below 37.8°C (100°F) as “flammable,” and products with flash points ator above 37.8°C and below 93.3°C (200°F) “combustible.” Products with flash points above93.3°C (200°F), when used for their intended purposes, are not classified as fire hazards inaccordance with OSHA (29 CFR 1910.1200).

Petroleum products should not be stored or handled near sources of ignition, such as heat,sparks, open flame, sources of static electricity, or near strong oxidants such as chlorine(including swimming pool chemicals) and concentrated oxygen.

WARNING: “Empty” containers retain residue (liquid and/or vapor) and can be dangerous. Donot pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame,sparks, static electricity, or other sources of ignition which may cause them to explode. Do notattempt to clean since residue is difficult to remove, and even a trace of remaining materialconstitutes an explosive hazard. “Empty” drums should be completely drained, properly bunged,and promptly returned to a drum reconditioner. All other containers should be disposed of in anenvironmentally safe manner and in accordance with governmental regulations.


HEALTH AND SAFETY PRECAUTIONS(continued)

44

HEALTH HAZARDS

Health studies have shown that many petroleum hydrocarbons pose potential human health risksthat may vary from person to person. As a precaution, exposure to liquids, vapors, and mists ofpetroleum products should be minimized.

Inhalation—Health specialists have established maximum concentration levels for hydrocarbonvapors in air to which nearly all workers may be safely exposed. Where applicable, the levelsestablished for Mobil products are indicated in Material Safety Data Sheets. Prolonged breathingof hydrocarbon vapor concentrations in excess of prescribed l imits may result inlight-headedness, dizziness, and nausea. Inhalation of higher vapor concentrations may producedizziness, headache, respiratory tract irritation, and unconsciousness.

If a person is overcome by vapor, remove the individual from exposure at once and call aphysician. If breathing is irregular or has stopped, start resuscitation and administer oxygen, ifavailable.

To avoid inhalation of excessive concentrations of hydrocarbons, store and handle highly volatilepetroleum products such as solvents and solvent-cutback products only in open, well-ventilatedareas. In special cases of indoor handling, e.g., laboratories, products always should be handledunder vented hoods powered with explosion-proof motors.

Under certain circumstances, sulfur compounds in hot asphalt may form the toxic gas hydrogensulfide (H2S). Prolonged breathing of 50 to 100 ppm of H2S will produce eye and respiratory tractirritation, headache, nervousness, and nausea. At higher concentrations of H2S (700 to 1000ppm) only a few breaths of the gas may lead to unconsciousness and could be fatal. To avoidbreathing excessive concentrations of H2S, personnel should stand upwind of tank and bulktransport compartments containing asphalt, keep their faces at least two feet from compartmentopenings, and avoid breathing vapors when opening hatches and dome covers. Use respiratoryequipment where necessary.

Ingestion—As a general precaution, if petroleum products are ingested, keep the person calm.DO NOT induce vomiting. Call a physician immediately, identifying the product and approximateamount swallowed. While petroleum products are generally not highly toxic, solvents and lightoils with viscosities below 20.5 centistokes (100 SUS) at 37.8°C (100°F) pose a distinct hazard ofbeing aspirated into the lungs and causing chemical pneumonitis. This is a delayed effect, whichmay not occur for days. Because of the risk of accidental swallowing, petroleum products shouldnever be siphoned by mouth.

Skin Contact—Prolonged or repeated contact of petroleum oils, greases, or solvents with theskin can cause skin irritation and dermatitis. In case of skin contact, wash skin thoroughly withsoap and warm water. A waterless hand cleaner and a soft skin brush can be used to helpremove oils and greases. For certain products, dry-wiping is advised before using waterless handcleaner. Refer to the product MSDS for specific instructions and precautions. Promptly removepetroleum-soaked clothing and launder before re-use. If a petroleum product contacts the eyes,flush the eyes with fresh water until the irritation subsides; if irritation persists, call a physician. Ifprolonged contact with petroleum products is unavoidable, wear chemical-resistant gloves,apron, splash goggles, and other protective clothing.


HEALTH AND SAFETY PRECAUTIONS(continued)

45

High-pressure injection of grease through the skin (a grease gun injury) can cause seriousdelayed damage to soft tissues. Hydraulic oil under high pressure can cause similar injury.Regardless of the size or appearance of the wound, a physician should be contactedimmediately, as treatment may require surgical intervention.

Chronic Health Effects—Although not the case with many highly or well refined petroleum oils,studies with laboratory animals have shown that prolonged exposure to certain petroleumproducts can cause cancer and other chronic health effects. Some petroleum oils and distillateshave caused skin cancer in mice following skin painting tests over the animals’ lifetime. In similartests, used motor oil also has caused skin cancer. Carefully check the product MSDS for suchwarning information. Inhalation of the vapors of most non-aromatic solvents has been shown tocause kidney damage in male rats. The normal hexane (n-hexane) component of hexane solventis known to cause a form of motor nerve damage called peripheral polyneuropathy in humans.

ADDITIONAL HEALTH AND SAFETY RECOMMENDATIONS

You can protect yourself from petroleum-related hazards by exercising care and common sensein the handling of petroleum products. Appropriate engineering controls, work practices, andpersonal protection should be used to minimize skin contact and to keep exposure by inhalationas far below the recommended occupational exposure limit as is reasonably practical.

Additional important health and safety information on any Mobil product is provided in the MobilMaterial Safety Data Sheet, available on the web at http://emmsds.ihspsl.com, by calling Fax-on-Demand at 1-613-228-1467, by calling the MSDS Order Desk at 1-856-224-4644, or bycontacting your local Mobil representative.


MATERIAL SAFETY DATA SHEETS (MSDSs)

46

Why Is a Material Safety Data Sheet Important to You?

Many petroleum products carry inherent health, environmental, and safety hazards. Carefulattention to the precautions and emergency procedures outlined in the appropriate MaterialSafety Data Sheet (MSDS) can protect you and your co-workers from these risks.

What Is an MSDS?

An MSDS is a publication designed to provide the user of a Mobil petroleum product withdetailed, comprehensive, and up-to-date health and safety information relating to that product.There is an individual MSDS for each Mobil product. The MSDS information is based onrequirements of Occupational Safety and Health Administration (OSHA) Regulation 29 CFR1910.1200, and the data presented are consistent with OSHA guidelines for informationalcontent. These data are derived from various sources, including Mobil testing laboratories,independent research organizations, and raw material suppliers.

What Kind of Information Does an MSDS Provide?

An MSDS typically contains the following types of information:

• Physical data on the product (e.g., boiling range, vapor pressure)

• The nature and degree of health, environmental, and safety hazards associated with theproduct

• Precautionary guidelines for proper and safe handling of the product in order to avoid fire,explosion, and acute and chronic health hazards

• Emergency procedures in the event of fire, spill, or excessive exposure to the product by skincontact, ingestion, or inhalation

How to Obtain an MSDS

We urge every user of Mobil products to obtain the appropriate MSDS. To obtain a sheet on anyMobil product

• visit us on the web at http://emmsds.ihspsl.com or www.mobil.com,

• call Fax-on-Demand at 1-613-228-1467 for a copy faxed immediately,

• call the MSDS Order Desk at 1-856-224-4644, or

• contact your Mobil representative.

ExxonMobil 24-Hour Emergency Line (Call Collect): 1-609-737-4411 in the U.S.


NOTES & TABLESADDITIVES FOR PREMIUM LUBRICATING OILS

47

AP

PE

ND

ICE

S

Many kinds of chemical additive agents are used in the manufacture of high-quality oils. They are either single-purposematerials or multipurpose materials. Listed below are descriptions of some commonly used additive types.

Adhesive AgentThe tacky, stringy materials which help form and retain uniform films on metal surfaces.

Antiwear AgentSuch materials adsorb or concentrate on metal surfaces to form films which minimize the direct metal-to-metal contact.The name applies to materials which enhance the antiwear characteristics of petroleum oils to permit loadings of doubleor triple that which can be handled by straight petroleum oils. These materials are nonstaining and noncorrosive.

DefoamantWhen added to fluids, defoamants will promote rapid breakup of foam bubbles by weakening the oil films between thefoam bubbles.

DemulsifierAssists the natural ability of the oil to separate rapidly from water; helps inhibit rust..

DetergentWhen added to oils, these neutral-to-overbased (high alkalinity), metallic detergents which carry extra neutralization andcleanliness power, can reduce the level of acidic materials generated when burning high-sulfur fuel, and help keep theengine clean.

DispersantSuspends organic deterioration products in the lubricant to minimize their precipitation as harmful deposits.

Extreme Pressure AgentThese materials are more active than antiwear agents. They react with metal surfaces to form relatively oil insolublesurface films which reduce friction, control wear and prevent surface damage which could result from heavy loads and/orhigh temperatures. Such materials are used, for example, in the Mobilgear 600 Series oils. Automotive hypoid gearsrequire lubricants which contain very active extreme pressure agents.

Friction ModifierA general category of materials that are used to alter the frictional characteristics of a lubricant. They may be used toincrease the lubricity or slipperiness where coefficient of friction may be important and to improve fuel economy/energyconservation. They may be used to reduce stick-slip or chatter in wet clutch applications.

Oxidation Inhibitor

• Peroxide decomposers destroy the precursor of radical sources by converting the peroxides into harmlesscompounds.

• Chain stoppers interrupt the chain reaction between oxygen and hydrocarbon radicals to prevent or slow theformation of acidic materials, propagated materials, and sludges.

• Metal deactivators retard the oxidation-promoting catalytic effect of metals in a lubricating system. The metalsurfaces or particles are covered by the agent which acts as a barrier to prevent the catalytic effect. The mostcatalytically active metal is copper; the second is lead, and the third is iron.

Some additive agents function as chain stoppers, peroxide decomposers, and/or metal deactivators.

Pour Point DepressantImproves the low-temperature fluidity of mineral oils and reduces wax formation at low temperatures.

Rust InhibitorThe primary guide to rust inhibition is the ASTM D 665 Rust Test, which is a pass/fail test. Most lubricating oils containrust inhibitors to enhance their ability to minimize rusting.

SpectographyA lab test method that measures the concentration of metallic particles smaller than ten microns.

Viscosity Index ImproverWhen added to oils, these high-molecular-weight polymers improve the viscosity index by coiling and uncoiling inresponse to temperature. They do not affect the pour point at low temperature while providing sufficient viscosity at hightemperature.


NOTES & TABLES

48

AP

PE

ND

ICE

S

SAE VISCOSITY GRADES FOR ENGINE OILS

Low-Temperature (C°) Low-Shear-Rate Low-Shear-RateLow-Temperature (C°) Pumping Kinematic Kinematic High-Shear-Rate

SAE Cranking Viscosity(4) (cP) Viscosity(5) (cSt) Viscosity(5) (cSt) Viscosity(6) (cP)Viscosity Viscosity(3) (cP) Max with at 100°C at 100°C at 150°C

Grade Max No Yield Stress(4) Min Max Min0W 6,200 at -35 60,000 at -40 3.8 — —5W 6,600 at -30 60,000 at -35 3.8 — —10W 7,000 at -25 60,000 at -30 4.1 — —15W 7,000 at -20 60,000 at -25 5.6 — —20W 9,500 at -15 60,000 at -20 5.6 — —25W 13,000 at -10 60,000 at -15 9.3 — —20 — — 5.6 < 9.3 2.630 — — 9.3 < 12.5 2.940 — — 12.5 < 16.3 2.9(7)

40 — — 12.5 < 16.3 3.7(8)

50 — — 16.3 < 21.9 3.760 — — 21.9 < 26.1 3.7

(1) Note: 1cP = 1mPa*s: 1cSt = 1mm2/s(2) All values are critical specifications as defined by ASTM D 3244(3) ASTM D 5393(4) ASTM D 4684; note that the presence of any yield stress detectable by this method constitutes a failure regardless of viscosity(5) ASTM D 445(6) ASTM D 4683, CEC L-36-A-90 (ASTM D 4741), or ASTM D 5481(7) 0W-40, 5W-40, and 10W-40(8) 15W-40, 20W-40, 25W-40, and 40

SAE J306 VISCOSITY GRADES FOR GEAR OILS

SAE Maximum TemperatureViscosity for BF Viscosity Kin ViscosIty, 100°C

Grade 150,000 cP min.(1) max.70W -55 C 4.1 —75W -40 C 4.1 —80W -26 C 7.0 —85W -12 C 11.0 —80 — 7.0 <11.085 — 11.0 <13.590 — 13.5 <24.0140 — 24.0 <41.0250 — 41.0 —

(1)Limits must also be met after testing in CEC L-45-T-93 Method C (20 hours)


NOTES & TABLES

49

AP

PE

ND

ICE

S

ISO VISCOSITY CLASSIFICATION SYSTEM

ISO Mid-Point Viscosity RangesViscosity cSt @ cSt @ 40°C Grades 40°C Minimum Maximum

2 2.2 1.98 2.423 3.2 2.88 3.525 4.6 4.14 5.067 6.8 6.12 7.4810 10 9.00 11.015 15 13.5 16.522 22 19.8 24.232 32 28.8 35.246 46 41.4 50.668 68 61.2 74.8100 100 90.0 110150 150 135 165220 220 198 242320 320 288 352460 460 414 506680 680 612 7481000 1000 900 11001500 1500 1350 1650


NOTES & TABLES

50

AP

PE

ND

ICE

S

GREASE CONSISTENCY CLASSIFICATION: NATIONAL LUBRICATING GREASE INSTITUTE (NLGI)AMERICAN STANDARD LUBRICATING GREASE CLASSIFICATION

60-STROKE WORKEDGRADE PENETRATION AT 77°F (25°C)

NLGI No. 000 445-475NLGI No. 00 400-430NLGI No. 0 355-385NLGI No. 1 310-340NLGI No. 2 265-295NLGI No. 3 220-250NLGI No. 4 175-205NLGI No. 5 130-160NLGI No. 6 85-115

The grades are defined as ranges of the values of the 60-stroke worked penetration, in tenths of millimeters, as determined by the ASTMDesignation D 217, “Cone Penetration of Lubricating Grease.”

VISCOSITY CONVERSION TABLERedwood Redwood Redwood

Kinematic SUS Engler No. 1 Sec. Kinematic SUS Engler No. 1 Sec. Kinematic SUS Engler No. 1 Sec.

2 32.6 1.14 30.8 46 214 6.15 190 240 1112 32 9903 36.0 1.22 33.2 50 233 6.65 207 250 1159 33 10304 39.1 1.31 35.8 55 256 7.25 228 260 1205 34 10705 42.5 1.40 38.4 60 279 7.9 248 270 1251 36 11106 45.7 1.48 41.0 65 302 8.6 268 280 1297 37 11507 49.0 1.56 43.7 70 325 9.25 286 290 1344 38 11908 52.0 1.65 46.5 75 349 9.85 307 300 1390 40 12309 55.7 1.74 49.2 80 372 10.5 329 315 1460 41 130010 59.0 1.83 52.1 85 395 11.2 349 330 1529 43 135011 62.5 1.92 55.2 90 418 11.8 370 350 1622 46 144012 66.2 2.02 58.4 95 442 12.5 390 370 1715 49 152013 70.0 2.12 61.6 100 465 13.2 410 390 1807 51 160015 77.5 2.32 68.2 110 511 14.5 450 410 1900 54 169017 85.5 2.55 75.2 120 558 15.8 490 430 1990 57 177019 94 2.77 82.8 130 605 17.1 530 450 2090 59 185021 100 3.00 90.4 140 649 18.4 570 470 2180 62 193023 111 3.23 98 150 695 19.7 620 490 2270 64 201025 120 3.46 106 160 742 21.0 660 500 2320 66 205028 133 3.83 117 170 788 22.5 700 550 2540 72 226030 142 4.09 125 180 834 24.0 740 600 2780 79 246033 155 4.46 137 190 881 25.0 780 650 3010 86 267035 164 4.71 145 200 927 26.0 820 700 3240 92 288038 178 5.10 157 210 973 28.0 860 750 3470 99 308040 187 5.35 166 220 1020 29.0 900 800 3700 105 328043 200 5.75 178 230 1066 30.0 940

DEGREES API CORRESPONDING TO SPECIFIC GRAVITIES AT 60/60°F AND POUNDS PER GALLONDegrees Specific Pounds Degrees Specific Pounds Degrees Specific Pounds

API Gravity (S.G.) Gallons API Gravity (S.G.) Gallons API Gravity (S.G.) Gallons

1.36 1.065 8.870 14.4 0.970 8.078 30.2 0.875 7.2861.99 1.060 8.829 15.5 0.965 8.036 31.1 0.870 7.2442.62 1.055 8.787 15.9 0.960 7.995 32.1 0.865 7.2033.26 1.050 8.745 16.7 0.955 7.953 33.0 0.860 7.1613.91 1.045 8.704 17.5 0.950 7.911 34.0 0.855 7.1194.56 1.040 8.662 18.2 0.945 7.870 35.0 0.850 7.0785.21 1.035 8.620 19.0 0.940 7.828 36.0 0.845 7.0365.88 1.030 8.578 19.8 0.935 7.786 36.9 0.840 6.9946.55 1.025 8.537 20.6 0.930 7.745 38.0 0.835 6.9527.23 1.020 8.495 21.5 0.925 7.703 39.0 0.830 6.9117.91 1.015 8.453 22.3 0.920 7.661 40.0 0.825 6.8698.60 1.010 8.412 23.1 0.915 7.620 41.0 0.820 6.8279.30 1.005 8.370 24.0 0.910 7.578 42.1 0.815 6.786

10.00 1.000 8.328 24.8 0.905 7.536 43.2 0.810 6.74410.70 0.995 8.287 25.7 0.900 7.494 44.3 0.805 6.70211.4 0.990 8.245 26.6 0.895 7.453 45.4 0.800 6.66112.2 0.985 8.203 27.5 0.890 7.41112.9 0.980 8.162 28.4 0.885 7.36913.6 0.975 8.120 29.3 0.880 7.328


NOTES & TABLES

51

AP

PE

ND

ICE

S

M = MEETSA = APPROVEDS = SUITABLE FOR USE

THE ABOVE IS NOT INTENDED TO REPLACE THE PRODUCTDATA SHEET WHICH CONTAINS THE MOST CURRENT INFORMATION

COMMERCIAL ENGINE OILS

SPECIFICATIONS COMMERCIAL ENGINE OILSMOBIL DELVAC

PRODUCT NAME DELVAC 1 1300 SUPER 1300 SUPER 1600VISCOSITY GRADE 5W-40 15W-40 10W-30 30, 40, 50API GASOLINE

SE (1972–1979) S SSF (1972–1979) S S SSG (1989–1993) S SSH (1994–1996) S SSJ (1997–2000) M M M

SL (2001– ) M M MAPI DIESEL

OFF HWY CF (1994– ) M M M M4-CYCLE CF-4 (1990– ) M M M

CG-4 (1995– ) M M MCH-4 (1999– ) M M MCI-4 (2002– ) M M M

ACEA DIESELE2 S ME3 ME4 ME5 M M

JASODH-1 M M M

ENGINE BUILDERSCATERPILLAR

ECF-1 M M MCUMMINS

CES 20071 S SCES 20076 A A ACES 20077 A ACES 20078 A A A

DETROIT DIESEL7SE 270 M M

MACKEO-M Plus A A A

EO-N Premium Plus 03 A AVOLVO

VDS S SVDS-2 S S SVDS-3 A A A

MERCEDES BENZSheet 228.3 A ASheet 228.5 A

ALLISONC-4 S S S (30 only)


SYNTHETIC DRIVE CONVENTIONALPRODUCT NAME MOBIL1 WITH SUPERSYN CLEAN PLUS DRIVE CLEANVISCOSITY GRADE 0W-20 0W-30 5W-30 10W-30 0W-40 15W-50 5W-30 10W-30 10W-40 5W-20 5W-30 10W-30 10W-40 20W-50 HD-30API SPECIFICATION

SL (2001- S S S S S S X X X X X X X X XILSAC GF-3 S S S S S X X X X

SH (1994-1996) S S S S S X X X X X X X XSJ (1997-2000) S S S S S S X X X X X X X X

ILSAC GF-2 S S S S S X X XACEA A1/B1, A5/B5 X X X X

(A1/B1ONLY)

ACEA A3/B3/B4 X XCF (1994- X X X X X X X X X

ENGINE BUILDERSGM

4718-M (Corvette) M X MFORD

M2C153-G X X X X XM2C153-H R X

CHRYSLERMS-9215 (Viper) X

MERCEDES BENZMB229.5 X

VW502/503.01/505 X

BMWLONGLIFE 01 X

NOTES & TABLES

52

AP

PE

ND

ICE

S

GASOLINE ENGINE OIL APPLICATION CHART

M=MEETSS=SURPASSESX=APPROVEDR=RECOMMENDED


R&O inhibited gearoil AGMA Lubricant Viscosity range cSt Extreme pressure gear oil Synthetic gear oil

No. at 40°C AGMA Lubricant No AGMA Lubricant No.0 28.8 to 35.2 None 0 S1 41.4 to 50.6 None 1 S2 61.2 to 74.8 2 EP 2 S3 90 to 110 3 EP 3 S4 135 to 165 4 EP 4 S5 198 to 242 5 EP 5 S6 288 to 352 6 EP 6 S

7, 7 Comp* 414 to 506 7 EP 7 S8, 8 Comp* 612 to 748 8 EP 8 S8A Comp* 900 to 1100 8A EP None

9 1350 to 1650 9 EP 9 S10 2880 to 3520 10 EP 10 S11 4140 to 5060 11 EP 11 S12 6120 to 7480 12 EP 12 S13 190-220 at 100°C*** 13 EP 13 S

14R** 428.5 to 857.0 at 100°C*** None None15R** 857.0 to 1714.0 at 100°C*** None None

AGMA Lubricant No. ISO Viscosity Grade Mobil Product Mobil Synthetic Product0 32 Mobil DTE Oil Light Mobil SHC 6241 46 Mobil DTE Oil Medium Mobil SHC 6252 68 Mobil DTE Oil Heavy Medium Mobil SHC 6263 100 Mobil DTE Oil Heavy Mobil SHC 6274 150 Mobil DTE Oil Extra Heavy Mobil SHC 6295 220 Mobil DTE Oil BB Mobil SHC 6306 320 Mobil DTE Oil AA Mobil SHC 6327 460 None Mobil SHC 634

AGMA Compounded Mobil Product7 Comp* 460 Mobil 600W Super Cylinder Oil8 Comp* 680 Mobil Extra Hecla Super Cylinder Oil

8A Comp* 1000 Mobil Extra Hecla Super Cylinder Oil Mineral

AGMA Lubricant No. ISO Viscosity Grade Mobil Product Mobil Synthetic Product2 EP 68 Mobilgear 626 None3 EP 100 Mobilgear 627 None4 EP 150 Mobilgear 629 Mobilgear SHC 1505 EP 220 Mobilgear 630 Mobilgear SHC 2206 EP 320 Mobilgear 632 Mobilgear SHC 3207 EP 460 Mobilgear 634 Mobilgear SHC 4608 EP 680 None Mobilgear SHC 680

8A EP 1000 None Mobilgear SHC 10009 EP 1500 None Mobilgear SHC 150010 EP None Mobilgear SHC 320011 EP None None12 EP None None13 EP Mobiltac QQ None14R** None None15R** Mobiltac 325 NC, 375 NC None

* Oils marked “Comp” are compounded with 3% to 10% fatty or synthetic fatty oils.** Residual compounds-diluent type, commonly known as solvent cutbacks, are heavy oils containing a volatile, non-flammable diluent for east of application.

The diluent evaporates leaving a thick film of lubricant on the gear teeth. Viscosities listed are for the base compound without diluent.*** Viscosities of AGMA Lubricant Number 13 and above are specified at 100°C (210°F) as measurement of viscosities of these heavy lubricants at 40°C

(100°F) would not be practical.

ANSI-AGMA INDUSTRIAL GEAR LUBRICANTS 9005-D94

NOTES & TABLES

53

AP

PE

ND

ICE

SMobil Product Book.qxd 6/25/04 4:09 PM Page 53 chris Share 3:2004:G010702 Hahn Product Guides:Mobil Product Guide

ENGINE MANUFACTURER FUEL MODELS RECOMMENDATION

Ajax (Cooper Cameron) CG 2-Cycle Mobil Pegasus Special

Caterpillar CG 6.25" Bore Mobil Pegasus 805, 905CG 3400, 3500, 3600 Mobil Pegasus 805, 905LFG All Mobil Pegasus 805, 905, 605

Cooper Bessemer CG 2-Cycle Mobil Pegasus 701, 801CG 4-Cycle Mobil Pegasus 505, 805

Dresser Rand - Ingersoll Rand CG Category I Mobil Pegasus 701/30, 801/30, 505/30CG Category II Mobil Pegasus 701/30, 801/30, 505/30CG Category III Mobil Pegasus 505/30, 801/30

Clark CG 2-Cycle Mobil Pegasus 701, 801Enterprise CG All Mobil Pegasus 505, 805Fairbanks-Morse (MEP) CG 2-Cycle Mobil Pegasus 505/30, 505, 805Nordberg (Hatch and Kirk) CG All Mobil Pegasus 505

LFG All Mobil Pegasus 610Superior (Cooper Cameron) CG G, GT, GST, GTLA, GTLB Mobil Pegasus 710White (Cooper Cameron) CG 1700, 2400 Mobil Pegasus 805

LFG G, GT, GST Mobil Pegasus 610LFG 1700, 2400 Mobil Pegasus 605

Waukesha CG VHP - F2895, F3521, L5796, Mobil Pegasus 805, 905, 710L7047, P9390

G, GSI, GLCG VHP - F3524, L5794, L7044 GSI Mobil Pegasus 805, 905

- L5774, L5794 LT Mobil Pegasus 805, 905VSG - F11G, GSI, GSID Mobil Pegasus 805, 905

CG VGF - F18, H24, L36, P48 Mobil Pegasus 805, 905G, GL, GLD, GSID

CG AT 25/27, 8L, 12V, 16V, GL Mobil Pegasus 805, 905LFG VHP, AT Mobil Pegasus 605, 610BMG VHP, AT Mobil Pegasus 605DG All Mobil Pegasus 810

Worthington (Dresser Rand) CG 2-Cycle Mobil Pegasus 701, 801CG 2-Cycle TC Mobil Pegasus 801, 505CG 4-Cycle Mobil Pegasus 801, 505

NOTES & TABLES

54

AP

PE

ND

ICE

S

NATURAL GAS ENGINE OIL RECOMMENDATIONS

NOTES:1 - THE MOBIL PEGASUS 605 IS A PREFERRED ALTERNATIVE FOR CATERPILLAR LANDFILL GAS APPLICATIONS.

FUELS:CG - CLEAN GAS - NATURAL GAS 90–95% METHANE WITH <10 PPM H2S AND <5% LIQUID HYDROCARBON

LFG - LANDFILL GAS - 40–60% METHANE, 20–40% CO2, 500–1500 ppm H2S, 50–150 ppm CHLORINATED COMPOUNDS ANDQUANTITIES OF SILICON COMPOUNDS

DG - DIGESTER GAS - SEWER GAS - 50–70% METHANE, 20–30% CO2 CAN CONTAIN LARGE AMOUNTS OF CORROSIVECOMPOUNDS (H2S)

BMG - BIO - MASS GAS - SEE DIGESTER GAS

* YOU SHOULD ALWAYS CHECK WITH THE MANUFACTURER FOR LUBRICANT RECOMMENDATIONS


VISCOSITY CLASSIFICATION EQUIVALENTS

ISO VISCOSITY CLASSIFICATION SYSTEM

Many petroleum products are graded according to the ISO Viscosity Classification System,approved by the International Standards Organization (ISO). Each ISO viscosity grade numbercorresponds to the mid-point of a viscosity range expressed in centistokes (cSt) at 40°C. Forexample, a lubricant with an ISO grade of 32 has a viscosity within the range of 28.8–35.2, themidpoint of which is 32.

Rule-of-Thumb: The comparable ISO grade of a given product whose viscosity in SUS at 100°Fis known can be determined by using the following conversion formula:

SUS @ 100°F ÷ 5 =̃cSt @ 40°C

NOTES & TABLES

55

AP

PE

ND

ICE


NOTES & TABLES

56

AP

PE

ND

ICE

S

UNDERSTANDING OIL ANALYSIS

VISCOSITYProbably the most important single property of a lubricating oil. It is a major factor in the development of the load carryingability of an oil. It is defined as resistance to flow at 40 degrees Centigrade and typically reported in Centistokes (cSt).

WEAR METALSThe presence of these metals can indicate a wear problem on a microscopic level before the problem can be detected byconventional means. The existence of a wear problem is determined not only by absolute values of metals, but moreimportantly by a relative increase or trend in one or more of these metals.

METAL SOURCESIron Cylinders, Gears, Rings, Crankshafts, Liners, Bearings, RustChromium Rings, Bearing and Liner PlatingLead Bearing OverlaysCopper Hydraulic Pumps, Bearing Cages, Bushings, Bronze ComponentsTin Bearing Plating, CompressorsAluminum Pistons, Bearing and Pump, Blower and Compressor ImpellersNickel ValvesSilver Bearing and Bushing PlatingManganese Trace Element in Gas Turbine Components

CONTAMINANTSThese elements can be an indicator of contamination. The combination of contaminant and wear metals can indicate aharmful machine operating condition.

CONTAMINANT SOURCESSilicon Abrasive Dirt, Sealant, DefoamantBoron Anti-freeze, Oil AdditiveSodium Anti-freeze, Oil AdditivePotassium Anti-freeze, Oil AdditiveAcid Oil Degradation (TAN)Oxidation Thermal Degradation of OilWater Anti-freeze, Process Water, CondensationGlycol Anti-freezeFuel Fuel SystemSoot Incomplete Combustion, Blow-byChlorine Land Fill Gas, Sea Water

ADDITIVESA chemical substance added to oil to impart or improve certain properties.

ADDITIVE FUNCTIONSMagnesium Dispersant/Detergent (TBN)Calcium Dispersant/Detergent (TBN)Barium Dispersant/DetergentPhosphorus AntiwearZinc AntiwearMolybdenum Antiwear

For further information contact your Mobil representative or go to www.Mobil.com.


Date of Manufacture code interpretation

Sample manufacturing date: PA1L2

First letters indicate which plant manufactured the product.Example PA1L2 = Port Allen

The next two digits indicate theday of the month the product was made.Example PA1L2 = 1st day of the month

The next letter indicates the month of manufacture.Example PA1L2 = L indicates November as the month of manufacture

The last number indicates the year of manufacture.Example PA1L2 = 2002

PA1L2 means this product was made on November 1, 2002 at Port Allen.

Code Plant Code Plant

X Beaumont PA Port AllenP Paulsboro BY Bayonne

1WC Cicero OL OlatheYD Kansas City

NOTES & TABLES

57

AP

PE

ND

ICE

S

YARDMARK INTERPRETATION KEY — EXAMPLE OF DRUM LABEL

Code Month Code Month Code Month

A Jan E May J SeptB Feb F June K OctC Mar G July L NovD Apr H Aug M Dec

Mobil Almo 529Rock Drill Oil


NOTES

58

AP

PE

ND

ICE


NOTES

59

AP

PE

ND

ICE


NOTES

60

AP

PE

ND

ICE


Mobil 2004 Brief Product Book

Documents

Transcript of Mobil 2004 Brief Product Book