mm Pitch series · 1.27 mm pitch connector For PCB Straight Through hole Configuration of product...
Transcript of mm Pitch series · 1.27 mm pitch connector For PCB Straight Through hole Configuration of product...
Office automation equipment, instrumentation equipment, communications equipment, factory automation, etc.
Rated voltage
Rated current
Insulation resistance
Dielectric withstanding voltage
Contact resistance
250V AC (r.m.s.)
1 A
Over 1000 megohms at 100V DC
750V AC (r.m.s.) for PCS series
500V AC (r.m.s.) for PCS-XE series
35 milliohms or less (not applicable to some products)
PCS series1.27 mm Pitch Connectors
Outline
Features
PrincipalApplications
ElectricalCharacteristics
PCS series provides various 1.27 mm pitch smaller-sized high density interface connectors specifically designed for downsized electronic equipment.
• 20 - 96 contacts for board-to-cable connectors• Results in substantial labor saving; IDC type connection is standard for
cables. (AWG #28 or #30)• Soldering type connectors available• EMI-filtered design to meet FCC and other standards• Backshell has a robust interface structure.• Quick locking with metal latch• Panel-to-cable connectors available• Accessory is available for preventing connector misinsertion.• 34 - 150 contacts for board-to-cable connectors.• Even with many contacts, connectors can be easily inserted or extracted
due to a low insertion force design.• Drainage structure ensures cleaning solution does not remain in the
housing during flux removal. (For molded type male connectors)
mm Pitch1.27
Connectors
Document Disclaimer
When placing orders with us, minimum order quantities are set for every product.
Be sure to contact us before starting preliminary design of PCBs using our connectors.
The specifications and information shown in the catalog are subject to change without notice.
Reflow temperature profile(for reference purposes)
Flow temperature profile(for reference purposes)
The reflow temperature profile shown in this drawing is for reference purposes. This profile depends on requirements such as reflow equipment, soldering paste, and PCB size. Thus, this profile may not meet with your specific situation. Please evaluate your PCB-mounting soldering and set your own reflow temperature profile.
ΩApplicable products
The profile shown in this drawing is applicable only for those products shown above.
The flow temperature profile as shown above is for reference purposes. This profile depends on requirements such as the PCB size. Thus, this profile may not meet with your specific situation. Please evaluate your PCB-mounting soldering and set your own flow temperature profile.
ΩApplicable products
The profile shown in this drawing is applicable only for those products shown above.
PCS-XE( )SLFYTU( )+ PCS series through hole type connector
100~130˚C
260±5˚C
30~60sec
5sec
130~150˚C
250˚C
220˚C
(Peak)
(Full heating period)30sec
(Preheating period)60~120sec
Panel mounting-hole dimensions for reference purposes
Dimensions of connector mounting for reference purposes
A
35 or more
40 or more
45.1 or more
54 or more
65.4 or more
73 or more
83.2 or more
35.5 or more
40.5 or more
46.2 or more
51.2 or more
B C
20
28
36
50
68
80
96
Number of contacts
Number of contacts A
27.4
32.5
37.6
46.5
57.9
65.5
75.69
B
23.7
28.8
33.9
42.8
54.2
61.8
72.0
C
11.3
16.3
20.3
30.3
40.3
50.3
20
28
36
50
68
80
96
10 or more
Pan
el th
ickn
ess:
t=
1.6
mm
MA
X.
In the case of using a mating guide
PCS-( )MD+ PCS-( )FD+
PCS-( )MD+ PCS-( )LFD+
PCS-( )LMD+ PCS-( )FD+
PCS-( )LMD+ PCS-( )LFD+
A
C
B
2.7
14.9
21.3
20.215
22.215
23.1
29.5
27.53
A
B
R1.4
7.5
2.8
A
B
C
R1.4
7.5
15 2.8
(In the case of PCS-E type)
Board-to-board connector dimensions for reference purposes
Board-to-cable connector dimensions for reference purposes (In the case of spring-locked type)
Edge of PCB
Product List
Straight through hole type male connector for PCBPCS-( )MD+
B-10PCSPCS series...8
Straight through hole type female connector for PCBPCS-( )FD+
B-11PCSPCS series...9
Right-angle through hole type male connector for PCBPCS-( )LMD+
B-12PCSPCS series...10
Right-angle through hole type female connector for PCBPCS-( )LFD+
B-13PCSPCS series...11
Right-angle through hole type male connector for PCBPCS-128LMDT-GP+
B-14PCSPCS series...12
Right-angle through hole type female connector for PCBPCS-128LFDT-GP+
B-15PCSPCS series...13
Straight through hole type male connector for PCBPCS-E( )MD+
B-16PCSPCS series...14
Right-angle through hole type male connector for PCBPCS-E( )LMD+
B-17PCSPCS series...15
IDC type female connector for cablePCS-E( )F( )
B-18PCSPCS series...16
Soldering type female connector for cablePCS-E( )FS+
B-19PCSPCS series...17
IDC type male connector for panelPCS-E( )PM( )-( )
B-20PCSPCS series...18
IDC type male connector for cablePCS-D( )( )MA1( )+
B-21PCSPCS series...19
IDC type female connector for cablePCS-D68( )FA1( )+
B-22PCSPCS series...20
Straight through hole type female connector for PCBPCS-XE( )SFD( )( )+
B-23PCSPCS series...21
Straight through hole type female connector for PCBPCS-XE( )SFD( )N( )+
B-24PCSPCS series...22
Right-angle through hole type female connector for PCBPCS-XE( )LFD( )( )+
B-25PCSPCS series...23
Right-angle through hole type female connector for PCBPCS-XE68LFDT( )N( )+
B-26PCSPCS series...24
Right-angle through hole type female connector for PCBPCS-XE100LFD( )-( )+
B-27PCSPCS series...25
Right-angle through hole type female connector for PCBPCS-XE( )SLFD( )( )+
B-28PCSPCS series...26
Right-angle through hole type female connector for PCBPCS-XE( )SLFDT( )( )+
B-29PCSPCS series...27
PCSRight-angle through hole type
female connector for PCBPCS-XE( )SLFD( )N( )+
B-30PCSPCS series...28
Right-angle through hole type female connector for PCBPCS-XE( )SLFDT( )N( )+
B-31PCSPCS series...29
Right-angle SMT type female connector for PCBPCS-XE( )SLFYTU( )+
B-32PCSPCS series...30
Straight Press-in type female connector for PCBPCS-XE50SFP( )( )
B-33PCSPCS series...31
IDC type male connector for cablePCS-XE( )M( )( )+
B-34PCSPCS series...32
Soldering type male connector for cablePCS-XES68MS+
B-35PCSPCS series...33
IDC type female connector for panelPCS-XE( )SPF( )1UN( )
B-36PCSPCS series...34
IDC type female connector for panelPCS-XE( )SPF( )( )( )
B-37PCSPCS series...35
IDC type female connector for panelPCS-XED( )( )FA( )( )+
B-38PCSPCS series...36
IDC type female connector for panelPCS-XED68( )FAUN( )+
B-39PCSPCS series...37
EMI-filtered vertical type die-cast material backshell for standard cablePCS-E( )L( )B-40PCSPCS series...38
Vertical type die-cast material backshell for larger diameter cablePCS-E( )LKB-41PCSPCS series...39
Mating guide structure vertical type die-cast material backshell for standard cablePCS-E( )LG( )B-42PCSPCS series...40
Horizontal type die-cast material backshell for standard cablePCS-E( )WB-43PCSPCS series...41
Vertical type plastic backshell for flat cablePCS-E( )LT+
B-44PCSPCS series...42
Vertical type die-cast material backshell for cable extensionPCS-E( )PML( )B-45PCSPCS series...43
Vertical type die-cast material backshell for standard cable with provision for preventing misinsertionPCS-E( )LP( )-( )+RB-46PCSPCS series...44
Vertical type die-cast material backshell for larger diameter cable with provision for preventing misinsertionPCS-E( )LKP( )-( )+RB-47PCSPCS series...45
Vertical type die-cast material backshell for larger diameter cable with mating guide for preventing misinsertionPCS-E96LKP( )-( )+RB-48PCSPCS series...46
Vertical type die-cast material backshell for larger diameter cable with provision for preventing misinsertionPCS-E96LKP1A-( )+RB-49PCSPCS series...47
PCS Vertical type die-cast material backshell
for standard cable with mating guide for preventing misinsertionPCS-E( )LGP( )-( )+RB-50PCSPCS series...48
Horizontal type die-cast material backshell for standard cable with provision for preventing misinsertionPCS-E( )WSP-( )+RB-51PCSPCS series...49
Horizontal type die-cast material backshell for larger diameter cable with provision for preventing misinsertionPCS-E( )WKP( )-( )+RB-52PCSPCS series...50
Horizontal type die-cast material backshell for larger diameter cable with provision for preventing misinsertionPCS-E96WKP( )-( )+RB-53PCSPCS series...51
Vertical type die-cast material backshell for flat cable with provision for preventing misinsertionPCS-E( )LTP-( )+RB-54PCSPCS series...52
Vertical type die-cast material backshell for larger diameter cablePCS-E68LKAU2NB-55PCSPCS series...53
Vertical type over-molded backshellPCS-XEM( )DL( )( )N
B-56PCSPCS series...54
Vertical type over-molded backshellPCS-XEM100L( )( )
B-57PCSPCS series...55
Vertical type die-cast material backshell for daisy chain connectionPCS-SE68LDAU2NB-58PCSPCS series...56
Dust-proof capPCS-68C
B-59PCSPCS series...57
Dust-proof capPCS-E( )C( )
B-60PCSPCS series...58
Dust-proof capPCS-E( )CP( )
B-61PCSPCS series...59
1.6 mm panel-thickness matingguidePCS-E( )G
B-62PCSPCS series...60
1.0 mm panel-thickness matingguidePCS-E( )G1
B-63PCSPCS series...61
Metallic mating guidePCS-E( )G3( )
B-64PCSPCS series...62
Metallic mating guide with provision for preventing misinsertionPCS-E( )G4-( )B-65PCSPCS series...63
Key rivet for preventing misinsertionPCS-E-PK+R
B-66PCSPCS series...64
Misinsertion prevention guidePCS-E( )PG-( )
B-67PCSPCS series...65
Misinsertion prevention guidePCS-E96PG-( )
B-68PCSPCS series...66
Spacer hardware for maleconnectorPCS-E( )M-SP
B-69PCSPCS series...67
PCSScrew lock
PCS-XE50SJ( )U2
B-70PCSPCS series...68
Plug-in type terminatorPCS-68FTH014X+
B-71PCSPCS series...69
1.27 mm pitch connector
For PCB
Straight Through hole
● Configuration of product Part No.
Mating connectors: PCS series PCB-side through hole type female connector
Accessories: Dust-proof cap, PCS-( )C
Straight through hole type male connector for PCBPCS-( )MD+
● Components
➀
➁
➀
➁
Contacts
Insulator
➀ ➁ ➂
PCS- ( ) MD+
ø0.8-+0.06
4-R1
LAST POS.
LAST POS.
POS.#2POS.#1
LAST POS.
LAST POS.
LAST POS.
Terminal No.
POS.#2
POS.#2POS.#1
POS.#1
B-+0.1
1.27
B
15˚
A
B
C
1.27
1.90
5±0.
05≈
3
9.3
5.7
7.3
2.54
1.27-+0.05
HO
ND
A
96
M
1
1.905≈3
3.4
œ0.4
➀ Series name➁ No. of contacts: 34, 48, 68, 96 or 150➂ Type of connector
MD: Straight through hole type, male
31.63
40.52
53.22
71.0
105.29
20.32
29.21
41.91
59.69
93.98
24.69
33.58
46.28
64.06
98.35
PCS-34MD+
PCS-48MD+
PCS-68MD+
PCS-96MD+
PCS-150MD+
A B C
● Dimensions
Recommended PCB layout(Connector side)
t = 1.6 mm
Form of connectors other than 96-contact connector
For 34-contact connector
For 34-contact connector
Part No.
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
Straight through hole type female connector for PCBPCS-( )FD+
1.27 mm pitch connector
For PCB
Straight Through hole
● Configuration of product Part No.
Mating connectors: PCS series straight through hole type male connector for PCB (Stacked height: 14.9 mm)
PCS series right-angle through hole type male connector for PCB
➀ ➁ ➂
PCS- ( ) FD+
● Components
➀
➁
Insulator
Contact
31.63
40.52
53.22
71.0
105.29
20.32
29.21
41.91
59.69
93.98
24.49
33.38
46.08
63.86
98.15
PCS-34FD+
PCS-48FD+
PCS-68FD+
PCS-96FD+
PCS-150FD+
A B C
LAST POS.
POS.#1POS.#2
4-R0.9
LAST POS. LAST POS.
POS.#2 POS.#1
LAST POS. LAST POS.
POS.#1
B-+0.1
1.27
B
A
B
C
1.27
5.6
5.0
10.6
RE
F.
5.5
7.3
2.54
1.27-+0.05
0.4≈0.35
1.905≈33.
4
➀ Series name➁ No. of contacts: 34, 48, 68, 96 or 150➂ Type of connector
FD: Straight through hole type, female
● DimensionsPart No.Recommended PCB layout
(Connector side)
t = 1.6 mm
For 34-contact connector
For 34-contact connector
ø0.8-+0.06
POS.#2
1.90
5±0.
05≈
315˚
➀
➁
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
For PCB
Right-angle Through hole
● Configuration of product Part No.
Mating connectors: PCS series straight through hole type female connector for PCB
PCS series right-angle through hole type female connector for PCB
Right-angle through hole type male connector for PCBPCS-( )LMD+
● Components➀
➁
➂
Insulator
Contacts
Bracket
➀ ➁ ➂
➂
PCS- ( ) LMD+
31.63
40.52
53.22
71.0
20.32
29.21
41.91
59.69
24.69
33.58
46.28
64.06
PCS-34LMD+
PCS-48LMD+
PCS-68LMD+
PCS-96LMD+
A B C
● DimensionsPart No.
➀ Series name➁ No. of contacts: 34, 48, 68 or 96➂ Type of connector
LMD: Right-angle through hole type, male
LAST POS.
POS.#2
LAST POS.
POS.#1
POS.#2
LAST POS.
POS.#1
LAST POS.
1.27
B
17.5
(10.
5MA
X)
4-R1
POS. #marking(4 PLCS)
LAST POS.
POS.#2
POS.#1
AB
C
1.27
5.7
7.3
2.54
1.27-+0.05
B-+0.1
1.905≈310.9
3.4
➀
➁15˚ œ0.4
Recommended PCB layout(Connector side)
t = 1.6 mm
For 34-contact connector
For 34-contact connector
ø0.8-+0.06
1.90
5±0.
05≈
3
Board-edge
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Right-angle through hole type female connector for PCBPCS-( )LFD+
1.27 mm pitch connector
For PCB
Right-angle Through hole
● Configuration of product Part No.
Mating connectors: PCS series straight through hole type male connector for PCB
PCS series right-angle through hole type male connector for PCB
➀ ➁ ➂
➀
➁
➂
PCS- ( ) LFD+
➀ Series name➁ No. of contacts: 34, 48, 68 or 96➂ Type of connector
LFD: Right-angle through hole type, female
● Components➀
➁
➂
Insulator
Contacts
Bracket
31.63
40.52
53.22
71.0
20.32
29.21
41.91
59.69
24.49
33.38
46.08
63.86
PCS-34LFD+
PCS-48LFD+
PCS-68LFD+
PCS-96LFD+
POS.#1
LAST POS.
POS.#2
LAST POS.
LAST POS.
POS.#1
POS.#2
LAST POS.
1.27
B
17.0
5.0
(4.8
MA
X.)
1.27-+0.05
B-+0.1
LAST POS.
POS.#1POS.#2
4-R0.9
A
B
C
1.27
5.5
7.3
2.54
5.2
0.35≈4
1.905≈3
3.4
● DimensionsPart No. A B C
Recommended PCB layout(Connector side)
t = 1.6 mm
For 34-contact connector
For 34-contact connector
ø0.8-+0.06
1.90
5±0.
05≈
3
Board-edge
15˚
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
For PCB
Right-angle Through hole
● Configuration of product Part No.
Mating connectors: PCS-128LFDT-GP+
Right-angle through hole type male connector for PCBPCS-128LMDT-GP+
● Components
➀
➁
➂
➃
Insulator
Contacts
Bracket
Lock pin
➀ ➃ ➄➁ ➂
➀➃
➁
➂
PCS- 128 LMD T- GP+
POS.#1POS.#2
3.4 3.65
89.52
82.8613.22.5
84.65
85.75
88.9
92.93
80.01
1.2710
.91.
905≈
3
21.9
RE
F.
17.5
4.4
5.7
7.3
1.1
4
2.54 1.1
3.5
4.5
80.01±0.1
88.9±0.1
(10.4 MAX.)
POS.#1POS.#2
2-ø2.3±0.1
LAST POS.
POS.#2POS.#1
LAST POS.
LAST POS.
➀ Series name➁ No. of contacts: 128➂ Type of connector
LMD: Right-angle through hole type, male➃ Lock pin➄ Mating guide
Recommended PCB layout(Connector side)
t = 1.6 mm
ø0.8-+0.06
1.905±0.05≈3
œ0.
4
1
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Right-angle through hole type female connector for PCBPCS-128LFDT-GP+
1.27 mm pitch connector
For PCB
Right-angle Through hole
● Configuration of product Part No.
Mating connectors: PCS-128LMDT-GP+
➀ ➃ ➄➁ ➂
PCS- 128 LFD T- GP+
● Components
➀
➁
➂
➃
Insulator
Contacts
Bracket
Lock pin
➀ Series name➁ No. of contacts: 128➂ Type of connector
LFD: Right-angle through hole type, female➃ Lock pin➄ Mating guide
80.01±0.1
88.9±0.1
POS.#2
POS.#1
LAST POS.
LAST POS.
POS.#2LAST POS.
POS.#1
POS.#2
3.4 3.65
86.75
84.852.3
88.9
92.93
82.76
80.01
89.92
1.27
5.2
1.90
5≈3
0.35
≈0.
4
17
5
7.3
5.5
13.
7
2.54 1
4.2
4.5
POS.#1
2-ø2.3±0.1
Recommended PCB layout(Connector side)
t = 1.6 mm
ø0.8±0.06
1.905±0.05≈3
➀➃
➁
➂
(4.7 MAX.)
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
For PCB
Straight Through hole
➀ Series name➁ No. of contacts: 20, 28, 36, 50 or 68➂ Type of connector
MD: Straight through hole type, male
● Configuration of product Part No.
Mating connectors: PCS-E series cable-side IDC type female connector
PCS-E series cable-side soldering type female connector
Accessories: Dust-proof cap, PCS-( )C( )
Straight through hole type male connector for PCBPCS-E( )MD+
➀
➀
➁
➁
➂
➂
PCS-E ( ) MD+
33.4
38.5
43.6
52.5
63.9
27.4
32.5
37.6
46.5
57.9
11.43
16.51
21.59
30.48
41.91
15.8
20.88
25.96
34.85
46.28
21.6
26.7
31.8
40.7
52.1
PCS-E20MD+
PCS-E28MD+
PCS-E36MD+
PCS-E50MD+
PCS-E68MD+
A B C D E
● DimensionsPart No.
● Components➀
➁
➂
Contacts
Insulator
Shell
POS.#2POS.#1 2-M2.5≈0.45
1.905≈3
E 0.85
1.27
C
E
0.85
A
B
C
1.27
D
7.0
3.4
2.54
5.7
5.5
4.0
10.5
9.3
POS.#1 POS.#2
LAST POS.
4-R1LAST POS.
2-ø2.8LAST POS.
LAST POS.
LAST POS.
B-+0.1
C-+0.1
1.27-+0.05
POS.#2
Recommended PCB layout(Connector side)
t = 1.6 mm
Except 50-contact connector
Except 50-contact connector
POS.#1
ø0.8-+0.06
1.90
5±0.
05≈
3
œ0.4
15˚
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Right-angle through hole type male connector for PCBPCS-E( )LMD+
1.27 mm pitch connector
For PCB
Right-angle Through hole
● Configuration of product Part No.
Mating connectors: PCS-E series cable-side IDC type female connector
PCS-E series cable-side soldering type female connector
Accessories: Dust-proof cap, PCS-( )C( )
➀ ➁ ➂
PCS-E ( ) LMD+
➀ Series name➁ No. of contacts: 20, 28, 36, 50, 68, 80 or 96➂ Type of connector
LMD: Right-angle through hole type, male
2-M2.5≈0.45
LAST POS.
LAST POS.
POS.#1
E0.85 0.85
1.27CFB
3.6
0.8
4
4.0
5.5
17.0
2.8
5.90
5
8.47
4.37
3.4
2.0POS.#2 2-M2.5≈0.45
ABC
1.27
D
7.0
2.54
5.7
10.5
POS.#1POS.#2
4-R1LAST POS.
2.00.8
LAST POS.
LAST POS.
B-+0.1
C-+0.1
1.27-+0.05
5.70
5
POS.#1
1.905≈3
Board-edge
2-ø2.8POS.#2ø0.8-+0.06
1.90
5±0.
05≈
315˚
œ0.4
33.4
38.5
43.6
52.5
63.9
71.5
81.7
27.4
32.5
37.6
46.5
57.9
65.5
75.69
11.43
16.51
21.59
30.48
41.91
49.53
59.69
15.8
20.88
25.96
34.85
46.28
53.9
64.06
21.6
26.7
31.8
40.7
52.1
59.7
69.9
PCS-E20LMD+
PCS-E28LMD+
PCS-E36LMD+
PCS-E50LMD+
PCS-E68LMD+
PCS-E80LMD+
PCS-E96LMD+
A B C D E
20.23
25.31
30.39
39.28
50.71
58.33
68.49
F
● DimensionsPart No.
● Components
➀
➁
➂
➃
Shell
Insulator
Contacts
Bracket
Recommended PCB layout(Connector side)
t = 1.6 mm
Except 50-contact connector
Except 50-contact connector
➀
➃
➁
➂
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
For cable
IDC (1.2 mm)
● Configuration of product Part No.
Mating connectors: PCS-E series through hole type male connector for PCB
PCS-E series IDC type male connector for panel
Tool: (Refer to page Tool-11)
IDC type female connector for cablePCS-E( )F( )
➀ ➃➁ ➂
➀
➃
➄
➄
➁
➂
PCS-E ( ) F ( )
● Components
➀
➁
➂
➃
➄
Contacts
Spacer
Shell
Insulator
Cable cover
21.65
26.7
31.8
40.7
52.1
59.7
69.9
11.43
16.51
21.59
30.48
41.91
49.53
59.69
15.4
20.48
25.56
34.45
45.88
53.5
63.66
PCS-E20F( )
PCS-E28F( )
PCS-E36F( )
PCS-E50F( )
PCS-E68F( )
PCS-E80F( )
PCS-E96F( )
A B C
● DimensionsPart No.
C
1.27B
A
B
1.27
5.5
2.54 7.3
5
13.2
POS.#1POS.#2
LAST POS.
POS.#1POS.#2
LAST POS.
Cable cover for discrete wire
Cable cover for flat cable
15˚
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
Note 1: This 96-contact connector is not available for flat cable.
➀ Series name➁ No. of contacts: 20, 28, 36, 50, 68, 80 or 96➂ Type of contact: Female➃ Cable sizes for reference purposes (In case the cable sheath is made of PVC resin)
Blank: AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insulation is 0.8–1.0 mm. For discrete wire.
A : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insuration is 0.5–0.65 mm. For discrete wire.
B : AWG#30(7 / 0.1). Outside diameter of wire is 0.5–0.65 mm. For discrete wire.C : AWG#28(7 / 0.127) For flat cableD : AWG#30(7 / 0.1) For flat cable (See Note #1)
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Soldering type female connector for cablePCS-E( )FS+
1.27 mm pitch connector
For cable
Soldering
● Configuration of product Part No.
Mating connectors: PCS-E series through hole type male connector for PCB
PCS-E series IDC type male connector for panel
➀ ➁ ➂
PCS-E ( ) FS+
➀ Series name➁ No. of contacts: 20, 28, 36, 50 or 68➂ Type of contact: Soldering type, female
Cable sizes for reference purposesFS: AWG#20 MAX.
● Components➀
➁
➂
➃
Contacts
Insulator
Shell
Spacer
A B C
● DimensionsPart No.
21.65
26.7
31.8
40.7
52.1
11.43
16.51
21.59
30.48
41.91
PCS-E20FS+
PCS-E28FS+
PCS-E36FS+
PCS-E50FS+
PCS-E68FS+
15.4
20.48
25.56
34.45
45.88
C
A
B
1.27
5.5
2.547.3
B
1.27
56
13.7
POS.#1POS.#2
LAST POS.
POS.#1POS.#2
LAST POS.
➀➃
➁
➂
15˚
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
For cable
IDC (1.27 mm)
● Configuration of product Part No.
Mating connectors: PCS-E series cable-side soldering type female connector
PCS-E series cable-side IDC type female connector
Accessories: Dust-proof cap, PCS-E( )C( )
IDC type male connector for panelPCS-E( )PM( )-( )
➀ ➃ ➄ ➅➁ ➂
PCS-E ( ) P M ( )- ( )
➀ Series name➁ No. of contacts: 20, 28, 36, 50 or 68➂ For panel➃ Type of contact: Male➄ Cable sizes for reference purposes (In case the cable insulation is made of PVC resin)
Blank: AWG#28(7 / 0.127). AWG#30(1 / 0.245). For flat cablesA : AWG#28(7 / 0.127). AWG#30(1 / 0.245). Outside diameter of insulation is
0.8–1.0 mm. For discrete wire.B : AWG#30(7 / 0.1). For flat cables.C : AWG#28(7 / 0.127) flat cable. AWG#30(1 / 0.245). Outside diameter of
insulation is 0.5–0.65 mm. For discrete wire.D : AWG#30(7 / 0.1). Outside diameter of wire is 0.5–0.65 mm. For discrete wire.
➅ Holes on mounting flangeBlank: M2.5≈0.45H : Diameter of hole: 2.7 mm (The connector is mounted on the Die-cast
material vertical backshell of PCS-E( )PML( ).)
● Components➀
➁
➂
➃
➄
Insulator
Shell
Contacts
Spacer
Cable cover
33.4
38.5
43.6
52.5
63.9
27.4
32.5
37.6
46.5
57.9
PCS-E20PM( )
PCS-E28PM( )
PCS-E36PM( ),-H
PCS-E50PM( )
PCS-E68PM( )
A B15.8
20.88
25.96
34.85
46.28
C11.43
16.51
21.59
30.48
41.91
D21.6
26.7
31.8
40.7
52.1
E21.65
26.7
31.8
40.7
52.1
F
● DimensionsPart No.
A B C
LAST POS.
10.5
5.7
15.6
2.45
3.65.5
4
4-R1
POS.#1
D E D F
1.27
1.27
0.85
0.85
Holes on mounting flange
For discrete wire For flat cable
➀
➃ ➄ ➄
➁
➂
15˚
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
This figure shows 36-contact connector as a typical example.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
or 68
63.9 57.9PCS-E68PM( ) 46.28 41.91 52.1 52.1
Accessories: Dust-proof cap, PCS-E( )C( )
IDC type male connector for cablePCS-D( )( )MA1( )+
1.27 mm pitch connector
For cable
IDC (0.635 mm)
Daisy chain
● Configuration of product Part No.
Mating connectors: PCS series straight through hole type female connector for PCB
PCS-XE series through hole type female connector for PCB
Required tools: MLPT-0003A (68 contacts) and MLPT-0003B (50 contacts) locators
➀ ➃ ➄ ➅➁ ➂
PCS-D ( ) ( ) M A 1 ( )+
● Components➀
➁
➂
➃
➄
Contacts
Insulator
Cable housing A
Cable housing B
Strain relief
➀ Series name➁ No. of contacts: 50 or 68➂ Strain relief
Blank: Not providedR : Provided
➃ Type of contact: Male➄ Cable size
A: AWG#30 (7 / 0.1) For flat cable
➅ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
A B C D EPart No.
40.13
51.56
30.48
41.91
34.85
46.28
PCS-D50( )MA1( )+
PCS-D68( )MA1( )+
36.8
48.23
31.115
42.545
LAST POS.
POS.#1 POS.#2
A
C
1.27
0.635
7.3
5.69
2.54
5.1
8.65
LAST POS. 4-R1.04
POS.#1
POS.#2
B
E
D 2.0
2.5
IDC direction
➀
➃
➄
➁
➂
15˚
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
● Dimensions
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
For cable
IDC (0.635 mm)
Daisy chain
● Configuration of product Part No.
Mating connectors: PCS series through hole type male connector for PCB
Required tools: Locator, MLPT-0006A (only for 68 contacts)
IDC type female connector for cablePCS-D68( )FA1( )+
➀ ➃ ➄➁ ➂ ➅
PCS-D 68 ( ) F A 1 ( )+
● Components➀
➁
➂
➃
➄
Contacts
Insulator
Cable housing A
Cable housing B
Strain relief
51.56
41.91
46.13
42.545
0.635
1.27
7.3
5.54
8.25
5
2.54
POS.#1POS.#2
LAST POS.
LAST POS. 4-R1
POS.#2 POS.#12.
02.
5
➀ Series name➁ No. of contacts: 68➂ Strain relief
Blank: Not providedR : Provided
➃ Type of contact: Female➄ Cable sizes
A: AWG#30 (7 / 0.1) For flat cable
➅ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
➀
➃
➄
➁
➂
IDC direction15˚
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Straight through hole type female connector for PCBPCS-XE( )SFD( )( )+
1.27 mm pitch connector
For PCB
Straight Through hole
SCSI-II
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
➀ ➃ ➄➁ ➂ ➅
PCS-XE ( ) S FD ( ) ( )+
● Dimensions
Part No.
Part No.PCS-XE26SFD( )( )+
PCS-XE50SFD( )( )+
PCS-XE68SFD( )( )+
37.2
52.5
63.9
31.2
46.5
57.9
15.24
30.48
41.91
19.46
34.7
46.13
27.05
42.29
53.72
20.0
35.24
46.67
A B C D E F
PCS-XE( )SFD( )+
PCS-XE( )SFDU( )+
PCS-XE( )SFDU2( )+
M2.5≈0.45
#4-40UNC
#2-56UNC
2.8
3.05
2.5
øGScrews size
● Components➀
➁
➂
➃
Shell A
Shell B
Insulator
Contacts
C
E
AB
C
D
F
LAST POS.
POS.#1
POS.#2 POS.#1
POS.#2
POS.#2 POS.#1
JAPA
N
HO
ND
A
5.4
3.4
1.27 0.35≈0.4
9.3
RE
F. 5.
51.
53.
8
0.85
1.27
8.2
5.54
2.54
4-R1
7
LAST POS.
1.905≈3
B-+0.1
C-+0.1
1.27-+0.05øG-+0.1
LAST POS.
LAST POS.
LAST POS.
Note 1: This 26-contact connector is not available for #4-40UNC and #2-56UNC screws.
Recommended PCB layout(Connector side)
t = 1.6 mm
15˚ Screw size
ø0.8-+0.06
1.90
5±0.
05≈
3
➀
➃
➁
➂
➀ Series name➁ No. of contacts: 26, 50 or 68➂ Type of shell
S: Short shell➃ Type of connector
FD: Straight through hole type, female
➄ Screw sizeBlank: M2.5≈0.45 (standard)U : #4-40UNCU2 : #2-56UNC
➅ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
For 68-contact connector For 68-contact
connector
••
•
•
•
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
➅ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
➅
((( )+
1.27 mm pitch connector
For PCB
Straight Through hole
SCSI-III
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector
Straight through hole type female connector for PCBPCS-XE( )SFD( )N( )+
➀ ➃ ➄➁ ➂ ➆➅
PCS-XE ( ) S FD ( ) N ( )+
52.5
63.9
84.3
46.5
57.9
78.23
30.48
41.91
62.23
34.7
46.13
66.45
35.24
46.67
66.99
42.1
53.5
73.85
PCS-XE50SFD( )N( )+
PCS-XE68SFD( )N( )+
PCS-XE100SFD( )N( )+ PCS-XE( )SFDN( )+
PCS-XE( )SFDUN( )+
PCS-XE( )SFDU2N( )+
● Dimensions
Part No.
Part No. A B C D E F
M2.5≈0.45
#4-40UNC
#2-56UNC
2.8
3.05
2.5
øGScrews size
● Components➀
➁
➂
➃
Shell A
Shell B
Insulator
Contacts
9.2
RE
F.
3.8
5.4
2.54
8.2
5.54
1.27C
D
EC
AB
POS.#2
POS.#2POS.#1
LAST POS.
POS.#1
POS.#2
4-R1
0.35≈0.41.27
5.0
F
LAST POS.
JAPA
N
HO
ND
A
3.4
1.905≈3
LAST POS.
LAST POS.
1.27-+0.05C-+0.1
B-+0.1
LAST POS.
Note 1: This 26-contact connector is not available for #4-40UNC and #2-56UNC screws.
➀ Series name➁ No. of contacts: 50, 68 or 100➂ Type of shell
S: Short shell➃ Type of connector
FD: Straight through hole type, female
➄ Screw sizeBlank: M2.5≈0.45U : #4-40UNC (standard)U2 : #2-56UNC
➅ Lock typeN: Screw lock
➆ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
Recommended PCB layout(Connector side)
t = 1.6 mm
For 68 or 100-contact connectors For 68 or 100-contact
connectors
➀
➃
➁
➂
•
••
•
••
15˚Screw size
POS.#1øG-+0.1
ø0.8-+0.06
1.90
5±0.
05≈
3
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
➆
(((( )+
➆ Contact platiBlank: MinG1 : Min
platingd plating
ating. 0.2 μm Gold . 0.76 μm Gold
Right-angle through hole type female connector for PCBPCS-XE( )LFD( )( )+
1.27 mm pitch connector
For PCB
Right-angle Through hole
SCSI-II
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
➀ ➃ ➄➁ ➂
PCS-XE ( ) LFD ( ) ( )+
Recommended PCB layout(Connector side)
t = 1.6 mm
For 68-contactconnector
For 68-contact connector● Components➀
➁
➂
➃
➄
Bracket
Shell A
Shell B
Insulator
Contacts
➀ Series name➁ No. of contacts: 50 or 68➂ Type of connector
LFD: Right-angle through hole type, female
➃ Screw sizeBlank: M2.5≈0.45 (standard)U : #4-40UNCU2 : #2-56UNC
➄ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
PCS-XE( )LFD( )+
PCS-XE( )LFDU( )+
PCS-XE( )LFDU2( )+
M2.5≈0.45
#4-40UNC
#2-56UNC
2.8
3.05
2.5
Part No. Screws size øG
PCS-XE50( )LFD( )( )+
PCS-XE68( )LFD( )( )+
52.5
63.9
46.5
57.9
Part No. A B30.48
41.91
C34.7
46.13
D42.29
53.72
E39.28
50.71
F
● Dimensions
POS.#1POS.#2
POS.#2LAST POS.
øG±0.1ø0.8±0.06
5.70
5 R
EF
.
1.90
5±0.
05≈
3LAST POS.
C±0.1
B±0.1
1.27±0.05
1.905≈3
4.03.
4
2
3.6
0.8
5.4 2.8
Screws size
Screws size
POS.#1POS.#2
POS.#1
POS.#1
LAST POS.
POS.#2
POS.#1POS.#2
17
1.5
5.5
5.90
5
0.85
D
C
E
C
F
1.27
B
24.
378.
47
A
B
1.27 ¢
∞
£
™
¡
4-R1
7
2.54
5.5
10.5
15˚
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
For PCB
Right-angle Through hole
SCSI-III
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
Right-angle through hole type female connector for PCBPCS-XE68LFDT( )N( )+
➀ ➃ ➄➁ ➂ ➅ ¶
PCS-XE 68 LFD T ( ) N ( )+
➀ Series name➁ No. of contacts: 68 ➂ Type of connector
LFD: Right-angle through hole type, female
➃ Board lock pinBlank: NoneT : Provided
➄ Screw sizeBlank: M2.5≈0.45U : #4-40UNC (standard)U2 : #2-56UNC
➅ Lock typeN: Screw lock
¶ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
● Components➀
➁
➂
➃
➄
➅
Bracket pin
Shell A
Shell B
Insulator
Board lock
Contacts
Recommended PCB layout(Connector side)
t = 1.6 mm
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
PCS-XE68LFDT( )N( )+ 63.9 57.9 41.91 46.13 50.71
Part No. A B C D
● DimensionsE
PCS-XE68LFDTN( )+
PCS-XE68LFDTUN( )+
PCS-XE68LFDTU2N( )+
M2.5≈0.45
#4-40UNC
#2-56UNC
2.8
3.05
2.5
Part No. Screws size øF
3.60.8
C±0.1
D
4.37
3.4
2.0
2.85
4 1.905≈3
1.90
5±0.
05≈
3
0.8§
8.47
øF±0.1
ø0.8±0.06
5.70
5 R
EF
.
Board-edge
B±0.1
LAST POS.
1.27±0.05
¢
∞
Screw size
POS.#1
POS.#2
£
¡
™
1.27
CB
A
10.5
5.5
15˚LAST POS.
2.54
B
E
C
1.27
16.9
5.4
5.90
5
LAST POS.
2.8
4-R1
POS.#2
POS.#1
POS.#1
POS.#2
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Right-angle through hole type female connector for PCBPCS-XE100LFD( )-( )+
1.27 mm pitch connector
For PCB
Right-angle Through hole
Screw lock
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
➀ ➃ ➄➁ ➂
PCS-XE 100 LFD ( )- ( )+
● Components➀
➁
➂
➃
➄
➅
Bracket
Ground plate
Shell
Insulator
Contacts
Lock screws
Part No.#4-40UNC
#2-56UNC
Screws sizePCS-XE100LFD( )-HS+
PCS-XE100LFD( )-HSU2+
POS.#1POS.#2
LAST POS.
2-ø3.051.27-+0.05
1.27≈49=62.23±0.1
78.23-+0.1
6.40
5MA
X.
86.01.27≈49=62.23
1.27 POS.#1POS.#2
POS.#2 POS.#1
8.74
2.54
5.5
16.9
5.4
6.70
5
78.2366.45
LAST POS.
1.27LAST POS.
5.5
3.7
M3≈0.5
6.4 REF.
4.6
4.05
1.905≈34.8
3.17
127≈49=62.2378.23
#4-40UNC
3.9
1.6
ø0.8-+0.06
1.90
5±0.
05≈
3
Recommended PCB layout(Connector side)
t = 1.6 mm
Screw size
Panel (Panel thickness: 1.6 mm)
Pan
el
thic
knes
s
➀
➃➄
➁
➂
➅
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
➀ Series name➁ No. of contacts: 100➂ Type of connector
LFD: Right-angle through hole type, female
➃ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
➄ Screw sizes for lock screwsHS : #4-40UNC (standard)HSU2: #2-56UNC
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
For PCB
Right-angle Through hole
SCSI-II
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
Right-angle through hole type female connector for PCBPCS-XE( )SLFD( )( )+
➀ ➃ ➄➁ ➂ ➅
PCS-XE ( ) S LFD ( ) ( )+
➀ Series name➁ No. of contacts: 26, 50 or 68➂ Type of shell
S: Short shell➃ Type of connector
LFD: Right-angle through hole type, female
➄ Screw sizeBlank: M2.5≈0.45 (standard)U : #4-40UNCU2 : #2-56UNC
➅ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
● Components➀
➁
➂
➃
➄
Bracket
Shell A
Insulator
Shell B
Contacts
37.2
52.5
63.9
31.2
46.5
57.9
15.24
30.48
41.91
19.46
34.7
46.13
27.05
42.29
53.72
PCS-XE26SLFD( )( )+
PCS-XE50SLFD( )( )+
PCS-XE68SLFD( )( )+
PCS-XE( )SLFD( )+
PCS-XE( )SLFDU( )+
PCS-XE( )SLFDU2( )+
● DimensionsPart No.Part No. A B C D E F
M2.5≈0.45
#4-40UNC
#2-56UNC
2.8
3.05
2.5
øGScrews size
24.05
39.28
50.71
POS.#2
1.905≈34.0
0.8
0.5
3.22.
04.
37
8.47
3.4
POS.#1
JAPAN HONDA
1.27-+0.05
C-+0.1
5.70
5 R
EF
.
BFC
7.0
POS.#2
LAST POS.
AB
C1.27
8.2
5.54
2.54
4-R10.4≈0.35
1.27
17.0
1.5
5.90
55.
5
0.85E
D
5.4
2.8
POS.#1
POS.#1
POS.#2
POS.#1
POS.#1
POS.#2LAST POS. LAST POS.
B-+0.1
øG
25
50
1
26
Board-edge
POS.#2 ø0.8-+0.06
1.90
5±0.
05≈
3
Recommended PCB layout(Connector side)
t = 1.6 mm
15˚
Screw size
Screw size
For 68-contactconnector
For 68-contact connector
➀
➃
➄
➁
➂
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
➅
((( )+
➅ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
Right-angle through hole type female connector for PCBPCS-XE( )SLFDT( )( )+
1.27 mm pitch connector
For PCB
Right-angle Through hole
SCSI-II
➀ Series name➁ No. of contacts: 26, 50 or 68➂ Type of shell
S: Short shell➃ Type of connector
LFD: Right-angle through hole type, female
➄ Board lock pin: Provided
➅ Screw sizeBlank: M2.5≈0.45 (standard)U : #4-40UNCU2 : #2-56UNC
➆ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
PCS-XE ( ) S LFD T ( ) ( )+
● Components➀
➁
➂
➃
➄
➅
Bracket
Shell B
Insulator
Shell A
Contacts
Board lock pin
37.2
52.5
63.9
31.2
46.5
57.9
15.24
30.48
41.91
19.46
34.7
46.13
27.05
42.29
53.72
PCS-XE26SLFDT( )( )+
PCS-XE50SLFDT( )( )+
PCS-XE68SLFDT( )( )+
PCS-XE( )SLFDT( )+
PCS-XE( )SLFDTU( )+
PCS-XE( )SLFDTU2( )+
● DimensionsPart No.Part No. A B C D E F
M2.5≈0.45
#4-40UNC
#2-56UNC
2.8
3.05
2.5
øGScrews size24.05
39.28
50.71
0.5
3.4
3.3
0.8
4 1.905≈3
4.37
8.47
BFC
1.27
17.0
1.5
5.90
55.
5
0.85
5.4
2.8
POS.#1
POS.#2
LAST POS.
E
7.0
LAST POS.
AB
C1.27
8.2
2.85
5.54
2.54
4-R10.4≈0.35
D
25
50
1
26
POS.#1
POS.#2
POS.#2
POS.#1
1.27-+0.05
C-+0.1
5.70
5 R
EF
.
POS.#1
POS.#2
POS.#1
LAST POS.
B-+0.1
øG-+0.05
Board-edge
POS.#2 ø0.8-+0.06
1.90
5±0.
05≈
3
Recommended PCB layout(Connector side)
t = 1.6 mm
15˚
Screw size
➀
➃
➄
➁
➂
➅
For 68-contact connector
For 68-contact connector
➀ ➃ ➄ ➆➁ ➂ ➅
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
((( )+➆
➆ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
1.27 mm pitch connector
For PCB
Right-angle Through hole
SCSI-III
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
Right-angle through hole type female connector for PCBPCS-XE( )SLFD( )N( )+
➀ ➃ ➄➁ ➂ ➅ ➆
PCS-XE ( ) S LFD ( ) N ( )+
➀ Series name➁ No. of contacts: 50 or 68 ➂ Type of shell
S: Short shell➃ Type of connector
LFD: Right-angle through hole type, female
➄ Screw sizeBlank: M2.5≈0.45U : #4-40UNC (standard)U2 : #2-56UNC
➅ Lock typeN: Screw lock
➆ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
● Components➀
➁
➂
➃
➄
Bracket
Shell B
Insulator
Shell A
Contacts
PCS-XE( )SLFDN( )+
PCS-XE( )SLFDUN( )+
PCS-XE( )SLFDU2N( )+
● Dimensions
Part No.
Part No. A B C D E
M2.5≈0.45
#4-40UNC
#2-56UNC
2.8
3.05
2.5
øFScrews sizePCS-XE50SLFD( )N( )+
PCS-XE68SLFD( )N( )+
52.5
63.9
46.5
57.9
30.48
41.91
34.7
46.13
39.28
50.71
0.5
3.2
0.8
1.905≈34
2.0
3.4 4.
37
BEC
1.27
0.4≈0.35
16.9
5.90
55.
4 2.8
POS.#1POS.#2LAST POS.
POS.#1
POS.#2
LAST POS.
AB
C1.27
8.2
5.54
2.54
4-R1
D
JAPAN HONDA
1.27-+0.05
C-+0.1
5.70
5 R
EF
.
POS.#1
POS.#2
POS.#2
POS.#1 POS.#1
LAST POS.
B-+0.1
øF
8.47
Board-edge
POS.#2 ø0.8-+0.06
1.90
5±0.
05≈
3
Recommended PCB layout(Connector side)
t = 1.6 mm
15˚
➀
➃
➄
➁
➂
For 68-contact connector
For 68-contact connector
Screw size
Screw size
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
➆
((((( )+
➆ Contact plaBlank: MinG1 : Min
d platingμm Gold plating
atingn. 0.2 μm Gold. 0.76 μm Go
Right-angle through hole type female connector for PCBPCS-XE( )SLFDT( )N( )+
1.27 mm pitch connector
For PCB
Right-angle Through hole
SCSI-III
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
➀ ➃ ➄➁ ➂ ➅ ➆ ➇
PCS-XE ( ) S LFD T ( ) N ( )+
➀ Series name➁ No. of contacts: 50 or 68➂ Type of shell
S: Short shell➃ Type of connector
LFD: Right-angle through hole type, female
➄ Board lock pin: Provided
➅ Screw sizeBlank: M2.5≈0.45U : #4-40UNC (standard)U2 : #2-56UNC
➆ Lock typeN: Screw lock
➇ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
● Components➀
➁
➂
➃
➄
➅
Bracket
Shell B
Insulator
Shell A
Contacts
Board lock pin
PCS-XE( )SLFDTN( )+
PCS-XE( )SLFDTUN( )+
PCS-XE( )SLFDTU2N( )+
● Dimensions
Part No.Part No. A B C D E
M2.5≈0.45
#4-40UNC
#2-56UNC
2.8
3.05
2.5
øFScrews sizePCS-XE50SLFDT( )N( )+
PCS-XE68SLFDT( )N( )+
52.5
63.9
46.5
57.9
30.48
41.91
34.70
46.13
39.28
50.71
0.5
3.2
0.8
1.905≈34
3.4 4.
37
BEC
1.27
16.9
5.90
55.
4
2.8
POS.#1POS.#2LAST POS.
POS.#1
POS.#2
LAST POS.
AB
C1.27
8.2
2.85
5.54
2.54
4-R10.4≈0.35
D
JAPAN HONDA
1.27-+0.05
C-+0.1
5.70
5 R
EF
.
POS.#1
POS.#2
POS.#2
POS.#1
POS.#1
LAST POS.
B-+0.1
øF-+0.1
8.47
Board-edge
POS.#2 ø0.8-+0.06
1.90
5±0.
05≈
3
Recommended PCB layout(Connector side)
t = 1.6 mm
15˚
Screw size
For 68-contact connector
For 68-contact connector
➀
➃
§➄
➁
➂
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
➇
((( )+
➇ Contact platBlank: Min. 0G1 : Min. 0
ld platingold plating
ing0.2 μm Gol0.76 μm Go
1.27 mm pitch connector
For PCB
Right-angle SMT
SCSI-II
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
Right-angle SMT type female connector for PCBPCS-XE( )SLFYTU( )+
➀ ➃ ➄ ➆➁ ➂ ➅
PCS-XE ( ) S LFY T U ( )+
➀ Series name➁ No. of contacts: 26 or 50 ➂ Type of shell
S: Short shell➃ Type of connector
LFY: Right-angle SMT type, female➄ Board lock pin: Provided➅ Screw size
U: #4-40UNC
➆ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
● Components➀
➁
➂
➃
➄
➅
➆
Contacts
Bracket
Shell A
Shell B
Insulator
Snap lock
Snap pin
● DimensionsPart No.
42.0
57.24
31.2
46.5
15.24
30.48
19.46
34.7
20.93
36.17
27.05
42.29
7.62
15.24
15.875
31.115
PCS-XE26SLFYTU( )+
PCS-XE50SLFYTU( )+
A B C D E F G H
3.2
0.85 0.85F
1.5
5.5
18.6
LAST POS. 0.635G
HB
POS.#1POS. #2
POS.#(contacts/2+1)
4.25
5.4
5.90
5
ø1.5
7
0.8
4.37
11.9
20.
53.
1
1.27
CBA
13
26
1
14
5.54
8.57
4-R1
LAST POS.DE
POS.#2
POS.#1
6.7-+
0.05
5.70
54.
05
4-+0.
05
E±0.1
B±0.1
0.635-+0.05
G-+0.05
2
H±0.1
2-ø4.5-+0.05
2-ø1.7-+0.1
0.6 REF.
Board-edge
Recommended PCB layout
15˚
➀
➃➄
➁
➂
➆
➅
Screw size
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Straight Press-in type female connector for PCBPCS-XE50SFP( )( )
1.27 mm pitch connector
For PCB
Straight Press-in
SCSI-II
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
➀ ➃ ➄➁ ➂
PCS-XE 50 SFP ( ) ( )
➀ Series name➁ No. of contacts: 50 ➂ Type of connector
SFP: Straight Press-in type, female➃ Screw size
Blank: M2.5≈0.45 (standard)U : #4-40UNCU2 : #2-56UNC
➄ Contact platingG1: Min. 0.76 μm Gold plating
POS.#1POS.#2
LAST POS.
46.5-+0.1
1.27-+0.05
30.48-+0.1
ø0.71+0.05-0.076
øF
1.905≈3
POS.#2
POS.#14-R1
1.2730.48
46.5
52.5
LAST POS.
7
34.7
10 5.54
2.54
13.4
RE
F.
4.8
8.3
5.1 1.5
POS.#1
POS.#2
LAST POS.
42.29
0.85
1.2730.48
5
1.90
5±0.
05≈
3
15˚
Recommended PCB layout(Connector side)
t = 2.4+0.2 mm
➀
➃
➄
➁
➂
➆
➅
● Components➀
➁
➂
➃
➄
➅
➆
Small flat head
Insulator A screw
Shell A
Shell B
Insulator B
Contacts
Hex. nuts
PCS-XE50SFP( )
PCS-XE50SFPU( )
PCS-XE50SFPU2( )
Part No.
M2.5≈0.45
#4-40UNC
#2-56UNC
2.8
3.05
2.5
øFScrews size
● Dimensions
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
For cable
IDC (1.27 mm)
SCSI-II, SCSI-III
● Configuration of product Part No.
Mating connectors: PCS-XE series straight or right-angle through hole type female connector for PCB.
PCS-XE series SMT type female connector.
For use with housings: SCSI-II: PCS-E( )L( ). SCSI-III: PCS-XEM( )DL( )( )N
Required tools: Discrete wire tool: PCS-K1 or FHAT-918B and FHPT-918A. Flat cable tool: PCS-K4
IDC type male connector for cablePCS-XE( )M( )( )+
➀ ➃ ➄➁ ➂
PCS-XE ( ) M ( ) ( )+
● Components➀
➁
➂
➃
➄
Contacts
Shell
Insulator
Spacer
Cable cover
● DimensionsPart No. A B C D
25.46
40.7
52.13
72.45
15.24
30.48
41.91
62.23
19.61
34.85
46.28
66.6
25.46
40.7
52.1
72.4
PCS-XE26M( )( )+
PCS-XE50M( )( )+
PCS-XE68M( )( )+
PCS-XE100M( )( )+
➀ Series name➁ No. of contacts: 26, 50, 68 or 100 ➂ Type of contact: Male➃ Cable sizes for reference purposes (In case the cable insulation is made of PVC resin)
Blank : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insulation is 0.8-1.0 mm. For discrete wire. (See Note #1)
A : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insulation is 0.5-0.65 mm. For discrete wire.
B : AWG#30(7 / 0.1). Outside diameter of insulation is 0.5-0.65 mm. For discrete wire.C : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). For flat cable, t = 1.0 mm MAX.
(See Note #2)E : AWG#30(7 / 0.1). For flat cable, t = 1.0 mm MAX. (See Note #2)J : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insulation is
0.65-0.8 mm. For discrete wire.K : AWG#30(7 / 0.1). Outside diameter of insulation is 0.65-0.8 mm. For discrete wire.Q : AWG#30(7 / 0.1). Outside diameter of insulation is 0.8-1.0 mm. For discrete wire.
➄ Contact platingBlank : Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
D
4-R1.04
1.27B
A
LAST POS.
7.3
5.7
2.54
POS.#1
LAST POS.
C
13.2
5
1.27B
POS.#1POS.#2
POS.#2
15˚
➀
➃
➄
➁
➂
Cable cover for discrete wire
Cable cover for flat cable
For 68 or 100-contact connector
Note 1: P/N PCS-XE100M+ is not available.Note 2: This 100-contact connector is not available
for flat cable. (C, E)
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Soldering type male connector for cablePCS-XES68MS+
1.27 mm pitch connector
For cable
Soldering
SCSI-III
● Configuration of product Part No.
Mating connectors: PCS-XE series straight or right-angle through hole type female connector for PCB,
PCS-XE series SMT type female connector for PCB, PCS-XE series of IDC type female connectors for cable panel
For use with housings: PCS-SE68LDAU2N
➀ ➁ ➂
PCS-XES 68 MS+
➀ Series name➁ No. of contacts: 68➂ Type of connector
MS: Soldering type, male
● Components➀
➁
➂
Shell
Insulator
Contacts
2.54
5.7
9.8
POS.#1 POS.#2
1.27
49.88
46.28
1.27≈(34-1)=41.91
LAST POS.4-R1.04
1.271.27≈(34-1)=41.91
5
11.5
17.6
RE
F.
3.05
3.05
POS.#2POS.#1
LAST POS.
➀
➁
➂
15˚
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
IDC type female connector for panelPCS-XE( )SPF( )( )( )
1.27 mm pitch connector
For cable
IDC (1.27 mm)
SCSI-II
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
➀ ➃ ➄➁ ➂ ➅ ➆ ➇
PCS-XE ( ) S P F ( ) ( ) ( )
● Components➀
➁
➂
➃
➄
➅
Insulator
Shell
Bracket
Spacer
Contacts
Cable cover
➀ Series name➁ No. of contacts: 26, 50 or 68 ➂ Type of shell
S: Short shell➃ Panel
P: Panel mounting➄ Type of contact
F: IDC type, female➅ Cable sizes for reference purposes
(In case the cable insulation is made of PVC resin)Blank : AWG#28(7 / 0.127) or AWG#30(1 /
0.254). Outside diameter of insulation is 0.8-1.0 mm. For discrete wire.
A : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). Outside diameter of insulation is 0.5-0.65 mm. For discrete wire.
B : AWG#30(7 / 0.1). Outside diameter of insulation is 0.5-0.65mm. For discrete wire.
C : AWG#28(7 / 0.127) or AWG#30(1 / 0.254). For flat cable,t = 1.0 mm.
E : AWG#30(1 / 0.1). For flat cable, t = 1.0 mm.
➆ Screw sizeBlank : M2.5≈0.54 (standard)U : #4-40UNCU2 : #2-56UNC
➇ Contact platingBlank : Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
Screw size
● DimensionsPart No.
37.2
52.5
63.9
31.2
46.5
57.9
15.24
30.48
41.91
19.46
34.7
46.13
27.05
42.29
53.72
PCS-XE26SPF( )( )( )
PCS-XE50SPF( )( )( )
PCS-XE68SPF( )( )( )
A B C D E25.46
40.7
52.1
F
13.2
4.4
5.5
2.54
1.5
10.5
5.54
1.27
C
D
C
A
B
POS.#2
POS.#2POS.#1
LAST POS.
POS.#1
1.27
LAST POS.
4-R1
F
75.
4
0.85
E
Cable cover for discrete wire
Cable cover for flat cable
Note 1: This 26-contact connector is not available for screw size, #4-40UNC or #2-56UNC.
For 68-contactconnector
➀
➃
➄
➁➂ ➅
15˚
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
For cable
IDC (0.635 mm)
SCSI-II
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
Required tools: Locator tool, MLPT-0004A for 68 contacts or MLPT-0004B for 50 contacts
IDC type female connector for panelPCS-XED( )( )FA( )( )+
➀ ➃ ➄ ➆➁ ➂ ➅
PCS-XED ( ) ( ) F A ( ) ( )+
➀ Series name➁ No. of contacts: 50 or 68 ➂ Strain relief
Blank: Not providedR : Provided
➃ Type of contactF: Female
➄ Cable sizeA: AWG#30(7 / 0.1) For flat cable
➅ Screw sizeBlank: M2.5≈0.54 (standard)U : #4-40UNCU2 : #2-56UNC
➆ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
● Components➀
➁
➂
➃
➄
➅
➆
Contacts
Insulator
Shell A
Shell B
Cable housing A
Cable housing B
Strain relief
● DimmensionsPart No.
52.5
63.9
46.5
57.9
30.48
41.91
34.7
46.13
42.29
53.72
PCS-XED50( )FA( )( )
PCS-XED68( )FA( )( )
A B C D E31.115
42.545
F42.1
53.47
G37.79
49.22
H39.49
50.92
J
Part No.M2.5≈0.45
#4-40UNC
#2-56UNC
Screws size
1
26
2
27
24
49
25
50
1
2
3
4
47
48
49
50
PCS-XED( )( )FA( )+
PCS-XED( )( )FAU( )+
PCS-XED( )( )FAU2( )+
A
B
C1.27
D
4-R1
POS.#1POS.#2
LAST POS.
7.0
2.54
5.548.2
F
G
E
0.85
0.635
5.4
5.5
1.5
4.99
7.85
H
J
2.0
2.5
➀
➃
➄
➁
➂
➆
➅
15˚
IDC direction
Conductor No.Terminal No.
● Terminal-to-conductor connection (In case of the 50-contact connector)
Screw size
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
POS.# Marking(4 PLCS)
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
IDC type female connector for panelPCS-XED68( )FAUN( )+
1.27 mm pitch connector
For cable
IDC (0.635 mm)
SCSI-III
● Configuration of product Part No.
Mating connectors: PCS-XE series IDC type male connector for cable
Required tools: Locator tool, MLPT-0004A for 68 contacts or MLPT-0004B for 50 contacts
➀ ➃ ➅➄ ➆ ➇➁ ➂
PCS-XED 68 ( ) F A U N ( )+
➀ Series name➁ No. of contacts: 68 ➂ Strain relief
Blank: Not providedR : Provided
➃ Type of contactF: Female
➄ Cable sizeA: AWG#30(7 / 0.1) For flat cable
➅ Screw sizeU: #4-40UNC
➆ Lock typeN: Screw lock
➇ Contact platingBlank: Min. 0.2 μm Gold platingG1 : Min. 0.76 μm Gold plating
● Components➀
➁
➂
➃
➄
➅
➆
Contacts
Insulator
Shell B
Shell A
Cable housing A
Cable housing B
Strain relief
0.635≈(68-1)=42.545
53.47
0.635
5.4
4.99
7.85
HO
ND
A
JAP
AN
63.9
57.9
1.27≈(34-1)=41.911.27
46.13
4-R1POS.#1POS.#2
LAST POS.
2.54
5.548.2
134
356849.22
50.92
2.0
2.5
1
35
2
36
33
67
34
68
1
2
3
4
65
66
67
68
Conductor No.Terminal No.
● Terminal-to-conductor connection
➀
➃
➄
➁
➂
➆
➅
15˚
IDC directionScrew size
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
Backshell
Vertical
EMI-filtered
● Configuration of product Part No.
EMI-filtered vertical type die-cast material backshell for standard cablePCS-E( )L( )
➀ ➃➁ ➂
PCS-E ( ) L ( )
➀ Series name➁ No. of contacts: 20, 28, 36, 50 or 68➂ Type of backshell
L: Vertical type backshell for standard cable➃ Identification mark (A, B or C) of cable-end-outlet dimension.
Cable diameters for reference purposes are shown in the Dimension table as below.
For use with connector: PCS-E series IDC type or soldering type female connector for cable
PCS-XE series IDC type male connector for cable
● Components➀
➁
➂
➃
➄
➅
Cover A
Cover B
Latch
†Small-sized Phillips flat head screw
Cable clamp
†Small-sized Phillips head screw
● DimensionsPart No.
30.0
35.0
40.2
48.9
60.3
20.3
25.3
30.5
39.2
50.6
ø5.5
ø7.5
ø4.3 ≠ ø8.7
ø5.5, ø5.9
ø9
ø8.4, ø9
ø7.3, ø8
ø8.1
6≈5
8≈7
10.3≈8.5
6.5≈5
9.5≈8.5
9.5≈8
8.5≈7
8.5≈7.5
PCS-E20LA
PCS-E20LB
PCS-E20LC
PCS-E28LA
PCS-E28LB
PCS-E36LA
PCS-E50LA
PCS-E68LA
A B C Outside diameter of cable for reference purposes
3210
A
C
B ➀
➃
➄
➁
➂
➅
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
1.27 mm pitch connector
Backshell
Vertical
EMI-filtered
● Configuration of product Part No.
Mating guide structure vertical type die-cast material backshell for standard cablePCS-E( )LG( )
➀ ➃➁ ➂
PCS-E ( ) LG ( )
➀ Series name➁ No. of contacts: 28, 36 or 50➂ Type of backshell
LG: Mating guide structure vertical type backshell for standard cable➃ Identification mark (A or B) of cable-end-outlet dimension.
Cable diameters for reference purposes are shown in the Dimension table below.
For use with connector: PCS-E series IDC type or soldering type female connector for cable
PCS-XE series IDC type male connector for cable
● Components➀
➁
➂
➃
➄
➅
Cover A
Cover B
Latch
Cable clamp
†Small-sized Phillips head screw
†Small-sized Phillips flat head screw
● DimensionsPart No. Outside diameter of cable
for reference purposes
35.0
40.2
48.9
PCS-E28LGB
PCS-E36LGA
PCS-E50LGA
A B C D E
25.3
30.5
39.2
30
34
42
16
31
39
ø9
ø7.5
ø8
8.5≈9.5
7≈7.5
7≈8.5
B
32
A
E
C
D
10
1.5
➀
➃➄
➁
➂
➅
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Horizontal type die-cast material backshell for standard cablePCS-E( )W
1.27 mm pitch connector
Backshell
Horizontal
EMI-filtered
● Configuration of product Part No.
For use with connector: PCS-E series IDC type or soldering type female connector for cable
PCS-XE series IDC type male connector for cable
➀ ➁ ➂
PCS-E ( ) W
● DimensionsPart No. Outside diameter of cable
for reference purposes
30.0
35.0
40.2
48.9
PCS-E20W
PCS-E28W
PCS-E36W
PCS-E50W
A
ø5.6
ø6
ø8.2
ø7.8
● Components➀
➁
➂
➃
➄
➅
Cover A
Cover B
Latch
†Small-sized Phillips flat head screw
Cable clamp
†Small-sized Phillips head screw
➀ Series name➁ No. of contacts: 20, 28, 36 or 50➂ Type of backshell
W: Horizontal type backshell for standard cable
25
32
A 1.5
10
➀
➃
➄
➁
➂
➅
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
Backshell
Vertical
● Configuration of product Part No.
Vertical type plastic backshell for flat cablePCS-E( )LT+
➀ ➂➁
PCS-E ( ) LT+
➀ Series name➁ No. of contacts: 28, 36 or 50➂ Type of backshell LT: Vertical type backshell for flat cable
For use with connector: PCS-E series IDC type female connector for cable
PCS-XE series IDC type male connector for cable
● Components➀
➁
➂
➃
➄
Cover B
Cover A
Latch
†Small-sized Phillips head screw
Hex nuts
● DimensionsPart No.
18.3
23.4
32.2
37.0
42.2
50.9
35.0
40.2
48.9
PCS-E28LT+
PCS-E36LT+
PCS-E50LT+
A B C
A
B
C
2010
➀➃➄ ➁➂
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Vertical type die-cast material backshell for cable extensionPCS-E( )PML( )
1.27 mm pitch connector
Backshell
Vertical
EMI-filtered
● Configuration of product Part No.
For use with connector: PCS-E( )PM( )-H
➀ ➁ ➂ ➃
PCS-E ( ) PML ( )
● Components➀
➁
➂
➃
➄
Cover A
Cover B
Cable clamp
†Small-sized Phillips head screw
†Small-sized Phillips flat head
➀➃
➄
➁
➂
D
A
C
B
2.5
27.5
3
10
2-M2.5
● DimensionsPart No. Outside diameter of cable
for reference purposes
37.6 27.3 8≈9.5 ø943.3PCS-E36PMLA
A
36
B C DNo. of contacts
➀ Series name➁ No. of contacts: 36➂ Type of backshell
PML: Vertical type backshell for PCS-E( )PM( )-H➃ Outside diameter of cable for reference purpose
A: 9 mm diameter
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
Backshell
Vertical
EMI-filtered
● Configuration of product Part No.
Vertical type die-cast material backshell for standard cable with provision for preventing misinsertionPCS-E( )LP( )-( )+R
➀ ➃ ➄➁ ➂
PCS-E ( ) LP ( )- ( )+R
For use with connector: PCS-E series IDC type or soldering type female connector for cable
PCS-XE series IDC type male connector for cable
Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R
● Components➀
➁
➂
➃
➄
➅
➆
Cover A
Cover B
Latch
Cable clamp
†Small-sized Phillips
head screw
†Small-sized Phillips
flat head screw
Key rivet
● DimensionsPart No. A B C Outside diameter of cable
for reference purposes
1B, 1C, 2A, 3A
1D, 2C, 3B, 4A
1E, 2D, 4B, 5A
30.0
35.0
40.2
48.9
60.3
20.3
25.3
30.5
39.2
50.6
ø5.5
ø7.5
ø5.5, ø5.9
ø9
ø10
ø8.4, ø9
ø7.3
ø8.1
ø6.5
6≈5
8≈7
6.5≈5
10≈8
11≈8
10≈8
10≈8
10≈8
7.5≈6
PCS-E20LPA-( )+R
PCS-E20LPB-( )+R
PCS-E28LPA-( )+R
PCS-E28LPB-( )+R
PCS-E28LPC-( )+R
PCS-E36LPA-( )+R
PCS-E50LPA-( )+R
PCS-E68LPA-( )+R
PCS-E68LPB-( )+R
Key-riveted position No.
CBA
321
DCBA
4321
DCBA
4321
32
A
C
B 10
1234BA
BA DC
21 43
DCBA
EDBA
54
C
321
EDBA
54
C
321
For 68-contactbackshell
For 50-contactbackshell
For 20-contactbackshell
For 28-contactbackshell
For 36-contactbackshell
Key-riveted position No.
➀➃
➄
➁
➂
➆
➅
➀ Series name➁ No. of contacts: 20, 28, 36, 50 or 68➂ Type of backshell
LP: Vertical type backshell for standard cables with provision for preventing misinsertion
➃ Identification mark (A, B or C) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below.
➄ Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Vertical type die-cast material backshell for larger diameter cable with provision for preventing misinsertionPCS-E( )LKP( )-( )+R
1.27 mm pitch connector
Backshell
Vertical
EMI-filtered
● Configuration of product Part No.
For use with connector: PCS-E series IDC type or soldering type female connector for cable
PCS-XE series IDC type male connector for cable
Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R
➀ ➁ ➂ ➃ ➄
PCS-E ( ) LKP ( )- ( )+R
➀ Series name➁ No. of contacts: 36, 50, 68 or 80➂ Type of backshell
LKP: Vertical type backshell for larger diameter cables with provision for preventing misinsertion
➃ Identification mark (A, B or C) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below.
➄ Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion.
B
32
A
10D
C
B CA
BA D EC
21 4 53
4 3 2 15
● Components➀
➁
➂
➃
➄
➅
➆
Cable clamp
†Small-sized Phillips head screw
Latch
Cover B
Cover A
†Small-sized Phillips flat head screw
Key rivet
Key-riveted position No.
➀
➃ ➄
➁
➂
➆
➅
● DimensionsPart No. Outside diameter of cable
for reference purposesKey-riveted position No.
10≈11
10≈12
10≈13
10≈10
15≈13.6
30.5
39.2
50.6
58.2
1D, 2C, 3B, 4A
1E, 2D, 4B, 5A
ø8
ø10.5
ø10
ø11.5
ø12
ø10
ø9.5
ø13
40.2
48.9
60.3
67.9
11.6
15.0
PCS-E36LKPA-( )+R
PCS-E36LKPB-( )+R
PCS-E50LKPA-( )+R
PCS-E50LKPC-( )+R
PCS-E68LKPA-( )+R
PCS-E68LKPB-( )+R
PCS-E80LKPA-( )+R
PCS-E80LKPB-( )+R
A B C D
EDBA
54
C
321
For 50,68 and 80-contactbackshell
DCBA
4321
For 36-contactbackshell
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
Backshell
Vertical
EMI-filtered
● Configuration of product Part No.
Vertical type die-cast material backshell for larger diameter cable with mating guide for preventing misinsertionPCS-E96LKP( )-( )+R
➀ ➃ ➄➁ ➂
PCS-E 96 LKP ( )- ( )+R
For use with connector: PCS-E series IDC type female connector for cable
PCS-XE series IDC type male connector for cable
Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R
➀ Series name➁ No. of contacts: 96➂ Type of backshell
LKP: Vertical type backshell for larger diameter cables with provision for preventing misinsertion
➃ Identification mark (A or B) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below.
➄ Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion.
● Components➀
➁
➂
➃
➄
➅
➆
Cover A
Cover B
Cable clamp
†Small-sized Phillips head screw
Latch
†Small-sized Phillips flat head screw
Key rivet
Part No. Outside diameter of cable for reference purposes Key-riveted position No.A
ø10
13≈7.5
ø10
ø7.5≈2
PCS-E96LKPA-( )+R
PCS-E96LKPB-( )+R
A
CBA52
52
5.2
58
36
78.1
C D EBA
3 4 521
11.6
10
CB EDA
Cable (The dimensions are shown below.)
➀
➃
➄
➁
➂
➆
➅
● Dimensions
1E, 2D, 4B, 5A
Key-riveted position No.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Vertical type die-cast material backshell for larger diameter cable with provision for preventing misinsertionPCS-E96LKP1A-( )+R
1.27 mm pitch connector
Backshell
Vertical
EMI-filtered
● Configuration of product Part No.
For use with connector: PCS-E series IDC type female connector for cable
PCS-XE series IDC type male connector for cable
Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R
➀ ➁ ➂ ➃ ➄
PCS-E 96 LKP1 A- ( )+R
A
CBA52
36
78.1
C D EBA
3 4 521
11.6
10
CB EDA
Key-riveted position No.
➀
➃
➄
➁
➂
➆
➅
➀ Series name➁ No. of contacts: 96➂ Type of backshell
LKP1: Vertical type backshell for larger diameter cables with provision for preventing misinsertion
➃ Identification mark (A) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below.
➄ Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion.
● Components➀
➁
➂
➃
➄
➅
➆
Cover A
Cover B
Cable clamp
†Small-sized Phillips head screw
Latch
†Small-sized Phillips flat head screw
Key rivet
● DimensionsPart No. Outside diameter of cable
for reference purposesA10≈9 ø10PCS-E96LKP1A-( )+R
Key-riveted position No.
1E, 2D, 4B, 5A
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
1.27 mm pitch connector
Backshell
Vertical
EMI-filtered
● Configuration of product Part No.
Vertical type die-cast material backshell for standard cable with mating guide for preventing misinsertionPCS-E( )LGP( )-( )+R
➀ ➃ ➄➁ ➂
PCS-E ( ) LGP ( )- ( )+R
For use with connector: PCS-E series IDC type or soldering type female connector for cable
PCS-XE series IDC type male connector for cable
Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R
➀ Series name➁ No. of contacts: 26 or 36➂ Type of backshell
LGP: Vertical type backshell for standard cables with mating guide for preventing misinsertion
➃ Identification mark (A) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below.
➄ Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion.
Part No. Outside diameter of cable for reference purposes
Key-riveted position No.
1D, 2C, 3B, 4A35.0
40.2
25.3
30.5
30
34
16
31
ø5.5, ø5.9
ø8.4, ø9
5≈6.5
8≈9.5
PCS-E28LGPA-( )+R
PCS-E36LGPA-( )+R
A B C D E
Key-riveted position No.
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
E
C
D
10
32
A
B1234BA
1.5
CA DB
31 42
DCBA
● Components➀
➁
➂
➃
➄
➅
➆
Cover A
Cover B
Latch
Cable clamp
†Small-sized Phillips head screw
†Small-sized Phillips flat head screw
Key rivet
Guide position of the 28-contact backshell
➀
➃➄
➁
➂
➆
➅
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
1.27 mm pitch connector
Backshell
Horizontal
EMI-filtered
● Configuration of product Part No.
Horizontal type die-cast material backshell for standard cable with provision for preventing misinsertionPCS-E( )WSP-( )+R
➀ ➃➁ ➂
PCS-E ( ) WSP- ( )+R
For use with connector: PCS-E series IDC type or soldering type female connector for cable
PCR series IDC type or soldering type female connector for cable
PCS-XE series IDC type male connectors for cable
Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R
➀ Series name➁ No. of contacts: 20, 28, 36 or 50➂ Type of backshell
WSP: Horizontal type backshell for standard cables with mating guide for preventing misinsertion
➃ Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion.
● DimensionsPart No. A B Outside diameter of cable
for reference purposes
1B, 1C, 2A, 3A
1D, 2C, 3B, 4A
1E, 2D, 4B, 5A
30.0
35.0
40.2
48.9
ø6
ø7.6
ø5
ø5.5
ø6
ø6.5
PCS-E20WSP-( )+R
PCS-E28WSP-( )+R
PCS-E36WSP-( )+R
PCS-E50WSP-( )+R
Key-riveted position No.
● Components➀
➁
➂
➃
➄
➅
Cover A
Cover B
Cable clamp
Latch A
Latch B
†Small-sized Phillips flat head screw
A B C D E
A B C D
A B C
10 A
22
A B C D
CA DB
31 42
31 42
Key-riveted position No. The form of the 50-contact backshell
The form of the 28-contact backshell
The form of the 20-contact backshell
➀
➃
➄
➁
➂
➅ 10
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
Horizontal type die-cast material backshell for larger diameter cable with provision for preventing misinsertionPCS-E( )WKP( )-( )+R
1.27 mm pitch connector
Backshell
Horizontal
EMI-filtered
● Configuration of product Part No.
For use with connector: PCS-E series IDC type or soldering type female connector for cable
PCS-XE series IDC type male connector for cable
Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R
➀ ➁ ➂ ➃ ➄
PCS-E ( ) WKP ( )- ( )+R
● DimensionsPart No. A B Outside diameter of cable
for reference purposes
1D, 2C, 3B, 4A
1E, 2D, 4B, 5A
40.2
48.9
60.3
67.9
10.5≈9.5
12≈10
11≈10
10.5≈9.5
ø9.5
ø11.5
ø10.5
ø9.5
PCS-E36WKPA-( )+R
PCS-E50WKPB-( )+R
PCS-E68WKPA-( )+R
PCS-E80WKPA-( )+R
Key-riveted position No.
➀ Series name➁ No. of contacts: 36, 50, 68, 80➂ Type of backshell
WKP: Horizontal type backshell for larger diameter cables withmating guide for preventing misinsertion
➃ Identification mark (A or B) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below.
➄ Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion.
● Components➀
➁
➂
➃
➄
➅
➆
Cable clamp
†Small-sized Phillips head screw
Latch
Cover B
Cover A
†Small-sized Phillips flat head screw
Key rivet
B11.6
10.0
12345
ABCDE
12345
A1.5
37.0
35.5
EDCB
Key-riveted position No.
➀
➃
➄
➁
➂
➆
➅
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
1.27 mm pitch connector
Backshell
Horizontal
EMI-filtered
● Configuration of product Part No.
Horizontal type die-cast material backshell for larger diameter cable with provision for preventing misinsertionPCS-E96WKP( )-( )+R
➀ ➃ ➄➁ ➂
PCS-E 96 WKP ( )- ( )+R
For use with connector: PCS-E series IDC type or soldering type female connector for cable
PCR series IDC type or soldering type female connector for cable
PCS-XE series IDC type male connector for cable
Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R
➀ Series name➁ No. of contacts: 96➂ Type of backshell
WKP: Horizontal type backshell for larger diameter cables with mating guide for preventing misinsertion
➃ Identification mark (B) of cable-end-outlet dimension. Cable diameters for reference purposes are shown in the Dimension table as shown below.
➄ Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion.
● DimensionsPart No. A B Outside diameter of cable
for reference purposesKey-riveted position No.
1096 15 ø10 1E, 2D, 4B, 5APCS-E96WKPB-( )+R
No. of contacts
5 4 3 2 1
10.0
B
12345
78.1
43.2
1.5
E D C B A
11.6A
A B C D E
● Components➀
➁
➂
➃
➄
➅
➆
Cable clamp
†Small-sized Phillips head screw
Latch
Cover B
Cover A
†Small-sized Phillips flat head screw
Key rivet
Key rivet(Option)
Key-riveted position No.
➀
➃
➄
➁
➂
➆
➅
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
Vertical type die-cast material backshell for flat cable with provision for preventing misinsertionPCS-E( )LTP-( )+R
1.27 mm pitch connector
Backshell
Vertical
● Configuration of product Part No.
For use with connector: PCS-E series IDC type female connector for cable
PCS-XE series IDC type male connector for cable
Accessories: Key-rivets for preventing misinsertion, PCS-E-PK+R
➀ ➁ ➂ ➃
PCS-E ( ) LTP- ( )+R
➀ Series name➁ No. of contacts: 50 or 68➂ Type of backshell
LTP: Vertical type backshell for flat cables with mating guide for preventing misinsertion
➃ Key-riveted position (Refer to the Dimension table as shown below) for preventing misinsertion.
● DimensionsPart No. A B C Key-riveted
position No.
50.9
62.3
48.9
60.31E, 2D, 4B, 5A
PCS-E50LTP-( )+R
PCS-E68LTP-( )+R
32.2
43.5
● Components➀
➁
➂
➃
➄
➅
➆
Cover B
Cover A
Latch
Cable clamp
†Small-sized Phillips head screw
Hex nuts
Key rivet
EDCBA
20
B
C
10
A
EDCBA
EDCBA
54321
Key-riveted position No.
➀➃➄ ➁➂
➅
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
1.27 mm pitch connector
Backshell
Vertical
SCSI-III
● Configuration of product Part No.
Vertical type die-cast material backshell for larger diameter cablePCS-E68LKAU2N
➀ ➃ ➅➄➁ ➂
PCS-E 68 LK A U2 N
For use with connector: PCS-E series IDC type female connector
PCS-XE series IDC type male connector for cable
➀ Series name➁ No. of contacts: 68➂ Type of backshell: Vertical type backshell for lager diameter housing➃ Identification mark (A) of cable-end-outlet dimension. Cable diameters for
reference purposes are shown below.➄ Screw size
U2: #2-56UNC➅ Lock type
N: Screw lock
Screw sizePart No.#2-56UNCPCS-E68LKAU2N
● Components➀
➁
➂
➃
➄
➅
Cable clamp
†Small-sized Phillips head screw
Thumb screw
Cover A
Cover B
†Small-sized Phillips flat head screw
ø12.5
ø12.2
57.9
63.8
JAPANLKA
JAPANLKA
17.5
32
382.
8513
.9
10.0
7.3
Screw size
Cable diameters for reference purposes
Assembly DiagramConnector
➀
➃
➄
➁
➂
➅
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
Vertical type over-molded backshellPCS-XEM( )DL( )( )N
1.27 mm pitch connector
Backshell
Vertical
SCSI-III
● Configuration of product Part No.
For use with connector: PCS-E series IDC type female connector
PCS-XE series IDC type male connector for cable
➀ ➁ ➂ ➃ ➄ ➅
PCS-XEM ( ) DL ( ) ( ) N
➀ Series name➁ No. of contacts: 50 or 68➂ Type of backshell
DL: Vertical type backshell➃ Color of hood
Blank: Black1 : Beige2 : Green3 : Grey
➄ Screw sizeBlank: M2.5≈0.45U : #4-40UNCU2 : #2-56UNC (standard)
➅ Lock typeN: Screw lock
● Components➀
➁
➂
➃
➄
➅
➆
Cable clamp
†Small-sized
Phillips head screw
Caps
Seal A
Seal B
Screw lock
Hood
Screw size
● DimensionsPart No.
Part No.
Outside diameter of cable for reference purposesA B C D E
17.6
19.3
ø10.5
ø12.2
PCS-XEM50DL( )( )N
PCS-XEM68DL( )( )N
ø11
ø12.7
54.0
65.43
46.5
57.9
14.0
15.7 M2.5≈0.45
#4-40UNC
#2-56UNC
PCS-XEM( )DL( )N
PCS-XEM( )DL( )UN
PCS-XEM( )DL( )U2N
D
C
A
B
11.2
2.85
23.0
46.0
14.0
E
Screw size
➀
➃
➄
➁
➂
➆
➅
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
1.27 mm pitch connector
Backshell
Vertical
Screw locks
● Configuration of product Part No.
Vertical type over-molded backshellPCS-XEM100L( )( )
➀ ➃ ➄➁ ➂
PCS-XEM 100 L ( ) ( )
For use with connector: PCS-XE series IDC type male connector for cable
➀ Series name➁ No. of contacts: 100➂ Type of backshell
L: Vertical type backshell➃ Color of hood
Blank: Black1 : Beige
➄ Screw sizeBlank: #4-40UNCU2 : #2-56UNC
● Components➀
➁
➂
➃
➄
➅
Cable clamp
†Small-sized Phillips head screw
Hood
Fastening screw
Shield B
Shield A
Screw size
● DimensionsPart No. Outside diameter of cable
for reference purposes
#4-40UNC
#2-56UNC
#4-40UNC
#2-56UNC
ø13.2
PCS-XEM100L
PCS-XEM100LU2
PCS-XEM100L1
PCS-XEM100L1U2
Black
Beige
Color of housing
4020
ø13.4
72
85.1
78.23
3.5
2.8
12.5
10
1437
10.8
16
51 R
EF.
➀
➃
➄
➁
➂
➅
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
Vertical type die-cast material backshell for daisy chain connectionPCS-SE68LDAU2N
1.27 mm pitch connector
Backshell
Vertical
SCSI-III
● Configuration of product Part No.
For use with connector: PCS-XES series soldering type male connector for cable
Mating connector: P/N: PCS-XES68MS
➀ ➁ ➂ ➃ ➄ ➅
PCS-SE 68 LD A U2 N
16.4 ø11.5
57.963.8
#2-56UNC
ø11
5545
25
2.85
13.2
5
11.4
➀
➁
➂
➃
➄
➅
➀ Series name➁ No. of contacts: 68➂ Type of backshell
LD: Vertical type backshell➃ Identification mark (A) of cable-end-outlet dimension.➄ Screw size
U2: #2-56UNC➅ Lock type
N: Screw lock
● Components➀
➁
➂
➃
➄
➅
Cable clamp
†Small-sized Phillips head screw
Thumb screw
Case B
Case A
†Small-sized Phillips head screw
Cable diameters for reference purposes
Assembly DiagramConnector
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
1.6 mm panel-thickness mating guidePCS-E( )G
1.27 mm pitch connector
Accessories
Mating guide
● Configuration of product Part No.
For use with connector: PCS-E series vertical type or horizontal type housing
➀ ➁ ➂
PCS-E ( ) G
● DimensionsPart No.
37.3
42.3
47.6
56.3
A B C D E F30.7
35.7
40.9
49.6
11
16
20
30
27.4
32.5
37.6
46.5
23.7
28.8
33.9
42.8
11.3
16.3
20.3
30.3
PCS-E20G
PCS-E28G
PCS-E36G
PCS-E50G
7.2
10.8
16.5
B
A
11.0
15.0
C
14.5
RE
F.
122.
5
t=1.6
1.5
EF
D
2.8
R1.4
7.5
15+
0.15
0
Recommended panel cut-out dimensions
For panel
➀ Series name➁ No. of contacts: 20, 28, 36 or 50➂ 1.6 mm panel-thickness mating guide
(Color: Silver metallic)
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
1.27 mm pitch connector
Accessories
Mating guide
● Configuration of product Part No.
1.0 mm panel-thickness mating guidePCS-E( )G1
➀ ➁ ➂
PCS-E ( ) G1
For use with connector: PCS-E series vertical type housing for standard cable or heavy wire cable with mating guide
➀ Series name➁ No. of contacts: 20, 28, 36, 50 or 68➂ 1.0 mm panel-thickness mating guide
● DimensionsPart No.
37.3
42.3
47.6
56.3
67.7
A B C D E F G30.7
35.7
40.9
49.6
61.0
11
16
20
30
40
33.0
38.1
43.2
52.1
63.5
27.4
32.5
37.6
46.5
57.9
23.7
28.8
33.9
42.8
54.1
11.3
16.3
20.3
30.3
40.3
H25
30
34
42
52
J8
16
31
39
49
PCS-E20G1
PCS-E28G1
PCS-E36G1
PCS-E50G1
PCS-E68G1
GF
E
2.8
R1.4
7.5
15+
0.15
0
B
H
A
11.0
12.2
15.0
J
C 1.7
12.5
10.4
121.
9
13.9
RE
F.
1.6
t=1.0
9.9
10.5
16.5
0.94
D
Recommended panel cut-out dimensions
For panel
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
Metallic mating guidePCS-E( )G3( )
1.27 mm pitch connector
Accessories
Mating guide
● Configuration of product Part No.
For use with connector: PCS-E series vertical type housing for standard cable or heavy wire cable
PCS-E series of horizontal type housing for standard cable or heavy wire cable
➀ ➁ ➂ ➃
PCS-E ( ) G3 ( )
➀ Series name➁ No. of contacts: 20, 28, 36, 50 or 68➂ Metallic mating guide➃ Guide plating
Blank: No platingN : Nickel plating
● DimensionsPart No.
33
38
43.1
52
63.4
PCS-E20G3( )
PCS-E28G3( )
PCS-E36G3( )
PCS-E50G3( )
PCS-E68G3( )
A B C D E F31
36.1
41.2
50.1
61.5
30.5
35.6
40.7
49.6
61.0
27.4
32.5
37.6
46.5
57.9
22.6
27.7
32.8
41.7
53.1
23.7
28.8
33.9
42.8
54.2
one side4
one side5
one side6
one side8
No. of dimples
7.2
E
D
C
B
A
F
R1.5
(R1.75)2.
8
7.5
10.7
11.2
MA
X.
(R2.75)
ø2.6
10
Note 1: Panel thickness: 1-1.6 mm
Dimples
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
Key rivet for preventing misinsertionPCS-E-PK+R
1.27 mm pitch connector
Accessories
Key rivet
● Configuration of product Part No.
For use with backshell: PCS-E series vertical type backshell or horizontal type backshell with provision for preventing misinsertion
➀ ➁
PCS-E- PK+R
0.7
1.65
ø1.
95
ø3
Caulk rivet(Use specialized tool.)
➀ Series name➁ Key rivet for preventing misinsertion
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
1.27 mm pitch connector
Accessories
Misinsertion prevention guide
● Configuration of product Part No.
Misinsertion prevention guidePCS-E( )PG-( )
➀ ➁ ➂ ➃
PCS-E ( ) PG- ( )
For use with connector: PCS-E series right-angle through hole type male connector for PCB
PCR-E series right-angle through hole type male connector for PCB
Mating backshell: PCS-E series of backshell with provision for preventing misinsertion
➀ Series name➁ No. of contacts: 20, 28, 36, 50, 68 or 80➂ Misinsertion prevention guide➃ Locations being cut off the key forms for preventing misinsertion
● DimensionsPart No. Standard locations being cut off the key
forms for preventing misinsertion
32.6
37.7
42.8
51.7
63.1
70.7
PCS-E20PG-( )
PCS-E28PG-( )
PCS-E36PG-( )
PCS-E50PG-( )
PCS-E68PG-( )
PCS-E80PG-( )
A B C30.3
35.3
40.5
49.2
60.6
68.2
27.4
32.5
37.6
46.5
57.9
65.5
1B, 1C, 2A, 3A
1D, 2C, 3B, 4A
1E, 2D, 4B, 5A
C
A
4-R1
7.5
10.1
1.5
1.1
RE
F.
2-R2.1
2-R1.3
1.1
1.5
3.7
B
6
M2.
5
0.8
ø4
1.7
0.2
MA
X.
1234
ABCD
1234
ABCD
12345
12345
ABCDE
ABCDE
12345
ABCDE
1234
ABCD
123
ABC
1234
ABCD
For 20-contacts
For 28-contacts
For 36-contacts
For 50-contacts
For 68-contacts
For 80-contacts
Note 2: Designate the location No. in parentheses (¢) for "Configuration of product part numbers." (Standard locations being cut off the key forms for preventing misinsertion are shown in the Dimension table.)
Example: PCS-E36G4-1D
Key No.
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
Note 1: When a panel is not used, use the spacer hardware, PCS-E( )M-SP.
Directional form
Attached small screw
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
Misinsertion prevention guidePCS-E96PG-( )
1.27 mm pitch connector
Accessories
Misinsertion prevention guide
● Configuration of product Part No.
For use with backshell: PCS-E series backshell with provision for preventing misinsertion. PCS-E96LKP( )-( )
➀ ➁ ➂ ➃
PCS-E 96 PG- ( )
ABCDE
12345
8 8 8 85
1.7
4.7 7.
6
2.5
2.1
10.1
7.5
1.5
3-R1
78.4
80.9
75.69
52
58
2-R1.3
2-R2.112345
ABCDE
60.8
ø4
M2.
5
Key No.
Directional form
Note1: Designate one of location numbers below in parentheses (¢) for "Configuration of product part numbers." (Standard locations being cut off the key forms for preventing misinsertion are shown below.)
Location No.: 1E, 2D, 4B or 5AExample: PCS-E96PG-1E
Attached small screw
➀ Series name➁ No. of contacts: 96➂ Misinsertion prevention guide➃ Locations being cut off the key forms for preventing misinsertion
Because some combinations of “Configurations of Product Part No.”, are under consideration for development, please contact us for availability details.
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole
1.27 mm pitch connector
Accessories
Spacer hardware
● Configuration of product Part No.
Spacer hardware for male connectorPCS-E( )M-SP
➀ ➁ ➂
PCS-E ( ) M-SP
For use with connector: PCS-E series right-angle through hole type male connector for PCB
PCR-E series right-angle through hole type male connector for PCB
➀ Series name➁ No. of contacts: 20, 28, 36, 50, 68 or 96➂ Spacer hardware for male connectors
C
B
A
7.5
10 2.6
2-R1.3
● Dimensions
Part No.32.8
37.9
43.0
51.9
63.3
81.1
27.4
32.5
37.6
46.5
57.9
75.69
22.8
27.9
33.0
41.9
53.3
71.1
PCS-E20M-SP
PCS-E28M-SP
PCS-E36M-SP
PCS-E50M-SP
PCS-E68M-SP
PCS-E96M-SP
A B CUse this spacer hardware for male connectors, when a panel is not used.
Plate thickness: 1.0 mm.
Others Wirewrapping Crimping Soldering IDC Press-in SMT Through
hole
Screw lockPCS-XE50SJ( )U2
1.27 mm pitch connector
Accessories
Screw locks
SCSI-III
● Configuration of product Part No.
For use with backshell: PCS-E series Backshells with provision for preventing misinsertion
➀ ➁ ➂
PCS-XE 50 SJ( ) U2
Part No.
8.9
5.5
3.9
4.5
2.7
4.1
3.5
–
1.1
PCS-XE50SJ1U2
PCS-XE50SJ5U2
PCS-XE50SJ6U2
A B C D E F G
3
2.9
3
–
0.8
#2-56UNC
4.75
5.48
RE
F. F
G
E
D
B C
A
#4-4
0UN
C
Note 1: SJ1 and SJ5 types are not slotted.
● Dimensions
➀ Series name➁ Kinds of screw locks
SJ1: The type not mounted on panel (Male screw size, #4-40UNC)SJ5: The type mounted on 1.6 mm panel (Male screw size, #4-40UNC)SJ6: The type mounted on 1.0 mm panel (Male screw size, #4-40UNC)
➂ Female screw sizeU2: #2-56UNC
OthersWirewrappingCrimpingSolderingIDCPress-inSMTThrough
hole