mitsui Parts Reference Manual - Mitsui High-tec€¦ · Jan 2004 Use of Parts Reference Manual 1....
Transcript of mitsui Parts Reference Manual - Mitsui High-tec€¦ · Jan 2004 Use of Parts Reference Manual 1....
Jan 2004
MITSUI PARTS REFERENCE MANUAL
MODELS:MSG-200MH MSG-205MHMSG-250MH
Jan 2004
Table of Contents3. General parts for 200/205/250MH5. Accessories for 200/250MH7. Cross feed for 200/250MH8. Fine cross feed attachment for 200/250MH11. Vertical feed for 200/250MH12. Fine vertical feed for 200/205/250MH14. Spindle head for 200/250MH16. Longitudinal feed parts for 200/205/250MH18. Coolant cover
Pg. 1
Jan 2004
Use of Parts Reference Manual
1. When ordering referenced parts you should now use part numbers to identify parts. Pictures are provided to clearly identify parts or assemblies.
2. Your part orders must include machine model and serial number for correct identification.
3. This manual is intended to be a reference to facilitate identifying and parts for Mitsui grinders. It is limited to the most commonly required parts and units. If you cannot identify a part quickly with this manual please contact your local distributor.
4. All photos are for reference only. Your part may differ from the photos.
5. You can also contact Mitsui High-tec (USA) for technical support (847-593-1634x101 or x110)
2Pg. 2
Jan 2004
GENERAL PARTS FOR 200/205/250MHCOLUMN DUST SHIELDFOR 200 P/N: CDS200 FOR 250 P/N : CDS250
WHEEL GUARD 8” P/N: WG8
CROSSFEED HAND WHEELFOR200M P/N: HWCF FOR 250M P/N : HWVF
HANDLE GRIP P/N: HGRIP
VERT. FEED HAND WHEELP/N: HWVF
LEVELING PLATESP/N : MG2001
GUIDE PLATE FOR DUST SHIELDFOR 200 P/N :MV2010N FOR 250 P/N: MV2510N
TABLE STOPPER P/N :ML2001
SADDLE STOPPER P/N :MC2007
HAND WHEEL L-NUT-ML2003
CROSS FEED V WAY WIPERFOR 200MH P/N:VW200FOR250MH P/N:VW250
TABLE END GUARDFOR 200 P/N :ML2009FOR250 P/N : ML2509
L/F HAND WHEELP/N:HWLF
CONTROL BOXP/N:CBOX220
CBOX440
SPINDLE ON SWITCHP/N : ME2001
SPINDLE OFF SWITCHP/N: ME2002
RUBBER MAT FOR 200 P/N: MG2004FOR 250 P/N : MG2005
WASHER P/N : MG2003
Pg. 3
CAP NUT P/N :MG2002
FOLD DOWN P/N: HGRIPF
SPRING WASHER, L/F – ML2002
Jan 2004
S/N DESCRIPTION200MH 205MH 250MH
1 Guide Plate For Column Dust Shield(New MV2510N2 Column Dust Shield CDS2503 Table End Guard ML25094 Hand Wheel Lock Nut for L/F5 Spring Washer for L/F6 Hand Wheel For Longitudinal Feed7 Hand Wheel For Cross Feed HWVF8 Hand Wheel For Vertical Feed9 Handle Grip
10 Handle Grip - Fold Down11 Cap Nut for Hand Wheel12 Washer for Hand Wheel13 Table Stopper 14 Saddle Stopper15 Rubber Mat for Saddle MG200516 Vee Way Wiper(4 Pcs.Set) VW25017 Control Box Std. 220V18 Control Box Std. 460V19 Spindle ON Switch(New)20 Spindle OFF Switch(New)21 Leveling Plate ( 3 Pcs Set)
Part Number
ML2003ML2002
MV2010NCDS200ML2009
GENERAL PARTS
MG2004VW200
MG2002MG2003ML2001MC2007
HGRIPF
HWLFHWCF
HWVFHGRIP
MG2001
CB220CB460
ME2001ME2002
Pg. 4
Jan 2004
Accessories for 200/250DUST SCOOPP/N - DS
BALANCING STAND & ARBORFOR 8” P/N – BSA8FOR12” P/N – BSA12
OVER WHEEL DRESSERFOR 8” P/N - OTW8FOR 12” P/N – OTW12
WHEEL ADAPTER FOR 8”STANDARD - P/N – WA8BALANCIN - P/N – BWA8
ONE SHOT LUBRICATORP/N - MANLUBWHEEL ADEPTOR WRENCH
P/N –MA2001 P/N – MA2002
Pg. 5
Jan 2004
S/N DESCRIPTION Part Number
1 Dust Scoop DS2 Over The Wheel Dresser for 8" Wheel OTW83 Over The Wheel Dresser for12" Wheel OTW124 Balancing Stand & Arbor for 8" Wheel BSA85 Balancing Stand & Arbor for 12" Wheel BSA126 Wheel Adapter Std.for 8" Wheel WA87 Wheel Adapter Bal.for 8" Wheel BWA88 Wheel Adapter Bal.for12" Wheel BWA129 One Shot Lubricator MANLUB
10 Wheel Adapter Wrench(Hook Type) MA200111 Wheel Adapter Wrench(Vee Type) MA2002
Mitsui Accessories
Pg. 6
Jan 2004
Cross Feed For 200/250MHCROSS FEED SCREW & BUSHING
STD FOR 200/205 –P/N –CF200 FINE, 200/205 – P/N – FC20
C/F SCREW COVERFOR 200 P/N : MC2001FOR 250 P/N : MC2501
THRUST BEARING for C/F #7202P/N :MC2004
CAP NUTMG2002
CROSS FEED BALL SCREWSTD. FOR 200 – P/N – CFBS200, FOR 250 – CFBS250FINE FOR 200 – P/N – FCBS200, FOR 250 – FCBS250
NUT STANDFor 200 P/N : MC2002:For 250 P/N : MC2502
CROSS FEED SCREW AND BUSHINGSTD FOR 250MH – P/N ; CF250FINE FOR 250MH – P/N: FC250
DIAL & SUB DIAL FOR C/F – FOR 200 P/N : MC2005FOR 250 P/N : MC2505
THUMBSCREWMG2006
NUT STAND FOR BALL SCREWFor 200 P/N : MC2003, For 250 P/N – MC2503
Pg. 7THRUST BEARING 51104 – P/N : MC2504
Jan 2004
Fine Cross Feed Attachment For 200/250MH
FINE CROSS FEED BALL SCREW(Not pictured)For 200MH P/N: FCBS200For 250MH P/N : FCBS250
FINE CROSS FEED SCREW & BUSHING For 200 P/N : FC200For 250 P/N : FC250
FINE CROSS FEED ATTACHMENT ASSEMBLYFOR 200MH P/N : FCA200FOR 250MH P/N : FCA250
FINE CROSS FEEDDIAL & SUB-DIALFOR 200 P/N : MC2006FOR 250 P/N : MC2506
KNOB FOR FINE FEEDP/N : MC2007
THUMB SCREWP/N :MG2006
Pg. 8
Jan 2004
S/N DESCRIPTION200MH 205MH 250MH
1 Cross Feed Screw & Bushing Std. Cf2502 Cross Feed Screw & Bushing Fine. FC2503 Cross Feed Ball Screw Std. CFBS2504 Cross Feed Ball Screw Fine. FCBS2505 Fine Cross Feed Attachment FCA2506 Screw Cover for C/F MC25017 Nut Stand Std. MC25028 Nut Stand For Ball Screw. MC25039 Thrust Bearing for C/F MC250410 Dial & Sub dial Assly for C/F MC250511 Dial & Sub dial Assly for Fine C/F MC2506
CROSS FEED PARTS
FCA200
MC2005MC2006
MC2003MC2004
Part Number
MC2001MC2002
CF200FC200
CFBS200FCBS200
Pg. 9
Jan 2004
V/F Parts for 200/250MHVERTICAL FEED SCREW & BUSHING STD
FOR200/205 P/N : VF200FOR250 P/N: VF250
VERTICAL FEED HAND WHEELP/N : HWVFDIAL & SUBDIAL FOR V/F
P/N :MV2001
Handle Grip OnlyP/N : HGRIP
Thumb Screw P/N : MG2007Pin for thumb screw P/N; MG2008
V/F SCREW COVER FOR 200/250(Not shown)P/N : MV2009 BELLOW FOR V/F WAY COVER
FOR 200 P/N : MV2011FOR 250 P/N: MV2511
Pg. 10
Jan 2004
Fine V/F for 200/205/250MH
DIAL FOR FINE FEEDP/N : MV2007
FINE VERTICAL FEED UNIT FOR200,205,250MHOptional in Place of Std V/F -- P/N - FV200
DIAL & SUB DIAL FOR V/FP/N : MV2006
CAP NUTP/N; MG2002
WASHERP/N :MG2003
KNOB FOR FINE FEEDP/N: MV2008
Pg. 11
Jan 2004
S/N DESCRIPTION200MH 205MH 250MH
1 Vertical Feed Screw & Bushing2 Dial & Sub dial for Vertical Feed3 Hand Wheel for Vertical Feed4 Thumb Screw5 Pin for Thumb Screw6 Vertical Feed Screw Cover7 Pinion and Spiral Gear set8 Pinion Shaft9 Lock Washer for V/F # 82
10 Lock Nut for V/F # 6511 Fine Vertical Feed Unit12 Dial & Sub dial for Fine Vertical13 Dial For fine Feed14 Knob for fine Feed15 Bellow for Vertical Way Cover MV2510MV2010
Part Number
HWVF
VF200MV2001
MG2007MG2008MV2009
VPS
VERTICAL FEED PARTS
MV2006MV2007MV2008
MV2003MV2004MV2005FV200
Pg. 12
Jan 2004
Spindle Head for 200/250SPINDLE STANDARD (New) – SP200SPINDLE STANDARD(Rebuilt) – SPRE OR SPRI(Rebuilt on exchange basis)
COUPLING ASSEMBLY STANDARD. – MS2006
SPINDLE MOTORMTR1K2P220P/N : MS2015
VERTICAL FEED SCREW & BUSHINGFor 200 – VF200For 250 – VF250
SPINDLE BOLTP/N - SPBOLT
RUBBER SPIDER(OLD)- P/N:MS2007(NEW) P/N ;MS2007A
SPINDLE NUTP/N – SPNUT
Pg. 13
Jan 2004
S/N DESCRIPTION200MH 205MH 250MH
1 Spindle Standard (New)2 Spindle Standard External(Rebuilt)3 Spindle Standard Internal (Rebuilt)4 Spindle Bolt5 Spindle Nut6 Coupling Assembly7 Rubber Spider (New) -8 Prong8 Rubber Spider (Old) - 2 Pcs set9 Spindle Motor Std-1kw2P220.10 Spindle Motor - 1kw2P46011 Spindle Motor -1.5kw2P22012 Spindle Motor -1.5kw2P46013 Spindle Motor -1.5kw4P22014 Spindle Motor -1.5kw4P460
MS2017MS2018MS2019MS2020
MS2007MS2007AMS2015MS2016
SPRISPBOLTSPNUTMS2006
Part Number
SP200SPRE
SPINDLE HEAD
Pg. 14
Jan 2004
L/F Parts for 200/205/250MHLINEAR BALL BEARINGSFor 200 – P/N : LB200For 205/250 – P/N : LB250
HARDENED STEEL WAYSNew For 200 – P/N – HS200New For205/250 – P/N – HS250Rebuilt For 200 – P/N – HS200RRebuilt For 205/250 – P/N – HS250R
LONGITUDINAL HAND WHEEL For 200/205/250 P/N: HWLF
TABLE LOCK ASSEMBLY200- P/N:2016250-P/N:2516
CABLEFor 200MH – CABLE200For 205MH – CABLE205For 250MH – CABLE250
RUBBER MAT For 200– P/N:MG2004For 250 – P/N: MG2005
Pg. 15
Jan 2004
S/N DESCRIPTION200MH 205MH 250MH
1 Hardened Steel Ways HS200 HS250 HS2502 Hardened Steel Ways( Rebuilt ) HS200R HS250R HS250R3 Linear Ball Bearing LB200 LB250 LB2504 Cable for Drum CABLE200 CABLE250 CABLE2505 Table Drum Lock Assly ML25166 Hand Wheel for L/F7 Hand Wheel Lock Nut for L/F8 Spring Washer for L/F9 Table Stopper Assly
10 Table End Guard ML2509
LONGITUDINAL FEED PARTS
ML2009ML2001
Part Number
ML2003ML2002
HWLGML2016
Pg. 16
Jan 2004
Coolant coverSPECIAL WHEEL GUARD
for 8” P/N : SPWG8COOLANT COVERCOMPLETELess Tank RUBBER SPLASH GUARD
P/N : FOR200 – ML2010FOR205 – ML2110FOR250 – ML2510
SPLASH GUARD FRONT(Metal)FOR 200 –ML2011FOR 205 – ML2110FOR250 – ML2510
TABLE DUST COVER
200MH 205MH 250MH
Coolant Cover Complete less Tank CC200 CC205 CC250Splash Guard (Rubber) ML2010 ML2110 ML2510
Splash Guard (Metal) ML2011 ML2111 ML2511
Table Dust Cover ( L & R) ML2012 ML2012 ML2512
COOLANT COVER PART NOS
Pg. 17