MINI HD CAMERA USER MANUAL
20
MINI HD CAMERA USER MANUAL
Transcript of MINI HD CAMERA USER MANUAL
MINI HD CAMERA USER MANUAL
Introduction
1
Power Button
Light Sensor
Camera Lens
Invisible Infrared LEDs
Force Shutdown Button
USB Charger Plug
System Reset Button
QR Code
Indicated Lights
SD Card Slot
Tech Spec.
2
Resolution
Video format
View angle
Motion detection distance
Infrared LED
Night vision distance
Min. illumination
Battery capacity
Battery life
Battery charging time
Audio recording range
Memory card
Power source
Operating temperature
Operating humidity
Computer software
Computer platform
Web browser
150°
6 meters / 20 feet
6
2 meters / 7 feet
1 Lux
500mA
50 - 120 minutes (Depending on use environment and camera configuration)
1 Hour
6 square meters / 20 square feet
Micro-SD card with up to 128GB (FAT32 format)
100-240V AC Power
-10 to 45 °C / -14 to 113 °F
15 - 85% RH
VLC Player / SM Player
Windows XP/Vista/7/8/10 and Mac OS X
IE7 and above, Chrome, Firefox, Safari, etc
AVI (H.264 Compression)
1080P@15fps, 720P@30fps, 640P@30fps, 480P@30fps
Button Operation
3
1 . Sometimes you may be unable to shut down camera by pressingthe Power button, you can try to use Forced Power Off button, Seedetails in next page “Force shutdown camera”.
2 . If camera doesn’t detect SD card, camera will not record. The blue or red light will only flash 1 time when you operate the Power button.
Turn on camera
Turn off camera 1
Quick-press the power button, the camera will turn on. Camera will be available to operate after 1 minute. Cam will be automatically turned on when the USB charger is plugged.
Unplug your USB charger from the camera, press Power button for 8 seconds at least, the cam is turned off. (When the camera is plugged in, long press the power button means all indicator lights are turned off, camera will shutdown once the USB charger is unplugged.)
Start recordingQuick-press power button when camera is running (Ensure the cam has an SD card in it), the red indicator light will flash 3 times, camera starts recording.
Stop recordingQuick-press power button when camera is running (Ensure the cam has an SD card in it), the blue indicator light will flash 3 times, camera stops recording.
2
2
Button Operation
4
Force shutdown camera
Press the button in the pinhole with a pin tool to force shutdown the camera when the Power button doesn't work.
Reset camera / Retore to defaultIf the cam is plugged with USB charger, please replug the USB plug 1 time.Ensure the cam is on, press the sys_reset button more than 5 seconds with a pin tool (During this process, all indicator lights will be turned off ). Camera will reset itself and restore default settings.
After reset success, the camera will be in Setupmode, the indicator lights will has red light is ON only.
APP: HdMiniCamName: CamPassword: 8888UID:HLXXXXXXXXXXXXXXXXXXXXX
NOTE: This function will not work when the USB charger is plugged, to use this function, please takeout the USB charger plug first.
1
1 . The indicator lights may be set to OFF if you disable it on app,or you had have long-pressed the Power button when the USB charger was plugged. For this case, in order to reset camera, please ignore the status of indicator lights, just press and hole the sys_reset button more than 10 seconds and then release it.
Indicator Lights Status
5
In order to get the cam working propetly,please read following status carefully.
General Status:
The camera contains 3 indicator lights.
All lights OFF
NOTE: Camera can’t be poweredoff when charging.
USB charger is NOT plugged
Yellow OFF: The camera is full charged.
Blue and Red ON: The camera is startup.
Blue ON and Red OFF: The camera is normally workingand the WiFi connection setup successfully.
Blue Blinking: The camera loses WiFi connection. You need to resetthe camera by referring to Page 4 and set up it again.
represents random status.
Blue OFF and Red ON: The camera is in Setup Mode.In this status, camera is unable to operate and requires for setup.
Yellow ON: The camera is charging.
All lights OFF:1. The camera is powered off.2. The indicator lights have been disabled on HDMINICAM app.
All lights OFF:1. The indicator lights have been disabled on HDMINICAM app.2. Long press Power button when USBcharger is plugged, all indicators willbe turned off. Cam will shut down oncethe USB plug is taken out.
USB charger is plugged
When the camera running, operate the Power button will be able to control camera to start or stop recording onto SD card, See what lightstatus you will get when you operate the Power button:
Indicator Lights Status
6
When the camera detects an SD card:
Recoding Status:
Blue light is flashing 3 times: The camera stops recording when quick-pressing Power button.
Red light is flashing 3 times: The camera starts recording when quick-pressing Power button.
Not detects SD card:
Blue light is flashing 1 time: No SD card detected or the SD card is not FAT32 format
Red light is flashing 1 time: No SD card detected or the SD card is not FAT32 format
To get the camera properly recorded video to SD card, please format the SD cardto FAT32 format, see FAQ E.
When camera starts recording, it records a 3-minute video clip by default when sensing motion. You can alter the recording duration time on app.
represents random status.
Connect Camera to Phone
7
1. Download HDMINICAM app
2. Make sure the camera is in Setup Mode
3. Go to phone WiFi settings
The HdMiniCam app is available on Apple app store and Google play store. Directly search “HDMINICAM” to download.
In Setup Mode, the camera’s lights will be (Blue OFF, Red constant ON). If the status is incorrect, please replug the USB plug andthen RESET the camera by refering Page 4.
In Setup Mode, camera willbroadcast a WiFi SSID, find outit in your phone WiFi settings.
Select it and get your phone connected to this WiFi SSID.
Please note that the WiFi SSID is the camera UID number.
Connect Camera to Phone
8
4. Go to HDMINICAM app
In general, the camera will be automatically added to HDMINICAMapp. If not, please tap “+” icon -> Add new online Camera.
5. Setup WiFi for camera
Tap icon and select Device Settings (Advance Config).
NOTE: If you don’t have a need to view feeds on phone, and justwant camera only work as video recorder and save video clips onto SD card, just stop here.
Connect Camera to Phone
9
6. Enter your WiFi password
Tap WiFi Config and then select your WiFi SSID from the WiFi lists.
Enter your WiFi password, please note the password is case sensitive.
NOTE: The camera only supports 2.4GHz WiFi, please do NOTchoose 5GHz WiFi SSID to connect.
10
Connect Camera to Phone
7. Complete setup and view live feed now
Learn about the buttons on live view:
After save the WiFi setting, the camera status will reboot itself, The status will be changed from Device Reboot to Online within 1 minute. Then you can view camera wherever you are!
Switch the resolution of live view.
Turn on/off the indicator lights.
Manually turn on/off the night vision.
Adjust the image contrast ratio.
Adjust the image brightness.
Turn ON/OFF the speaker of app.
Turn ON/OFF the microphone.
Snapshot current picture.
Start/Stop recording onto app.
Screen flips horizontal.
Screen flips vertical.
NOTE: Remotely accessing camera must require your home router is Internet access.
12
3
45
6
7
8
9
10
11
11
Download the PC tools from Titathink support website:https://support.titathink.com/downloads/software/pctools.zip
View Camera on Computer
1. Download and install PC software
After you install it successfully, find the IPCMultiViewon desktop and click on it.
Enter username and password to go ahead.
2. Login this software
NOTE: The default password for this software is empty,so please leave it blank.
NOTE: This ZIP file contains Windows version software andApple OS version software.
admin
12
View Camera on Computer
Click on to add the camera.
Click the “+” icon to add New IP Camera.
3-1. Add camera to software
NOTE: In order to add camera to PC software successfully, the camera must be in same local area network as the computer. Or the camera is connected to an Internet WiFi.
Change the video saved path
Add a New IP camera
13
Highlight the “New IP camera”, you need to enter the camera’sUID and Password. Next, click OK to save.
Click the Connect all cameras button to build the connection.
You will be able to view camera on your computer.
The camera UID and Password can be found at the rear side of camera body. The paddword is 8888 by default, if it’s changed onphone app, please use yours.
View Camera on Computer
3-2. Add camera to software
4. Build connection between camera and software
14
Before reading FAQ, please note that most of problems can be solved afterthe camera is fully charged and perform a reset operation.Please learn how to reset the camera by referring to page 3.
FAQ:
When the camera is being weird or it is always dropped, please fully chargeit and do a reset operation.
A. The night vision image is poor quality.
B. The camera can not be found when adding camera to app.
Limited by size, the camera is low power consumption design. So in order to makecamera works long time with battery in night and prevent the camera to be overheated, the infrared lights will work on low power mode. So the night visiononly can cover 2 meters / 7 feet range. The image will be poor quality if the camera is placed in complete dark environment. So if the night vision is necessary for you, you can leave a light around the camera or place an external infrared illiminator. Besides, you can adjust app->Device Settings->IR-LED Config->Set to Bright 99.This way may improve the image quality a little.
First of all, please power the camera with power adapter. And then check if the REDindicated light is lighted constantly, if not, please do a reset operation.Next, please ensure your phone has connected to the WiFi SSID which broadcastedby camera, and then try again.
C. You can not get the camera connected to WiFi.
First of all, please make sure the WiFi password you entered is correct. Please note that the password is case sensitive.Next, please ensure your WiFi is NOT working on 5GHz WiFi band. Becausethe camera is only compatible with 2.4GHz WiFi band. In generals, most of routerscan broadcast both 2.4GHz WiFi band and 5GHz WiFi band. You can access yourrouter to check if the 2.4GHz WiFi SSID is enabled or not.
If the camera has a successful WiFi connection, its blue indicated light will be lightedconstantly.
15
NOTE: If you set Record option to Record When Alarms. You need to set onapp->Device Settings->Alarm Config->Turn on Motion Detection Sensitivity.
FAQ:D. The camera on app says Device Request or Device Offline.
Firstly, see what they means:Device Request: The app is trying to communicate with camera, if success, it will switch to Online. Otherwise, it will switch to Device Offline.Device Offline: The app lost communication with the camera. Device Offline indicates the connection between camera and app is lost. You cancheck following points:1. Make sure your phone is in same network as camera’s. Or make sure phonenetwork is Internet access.2. Make sure the WiFi password you entered to camera is correct. The passwordis case sensitive.3. Make sure the WiFi network used by camera is 2.4GHz WiFi. Please read FAQ-C.4. If you meet this problem outside, please make sure your home router is Internetaccess, or you can reboot the router once time.5. Make sure the camera battery life is enough, plug in power adapter and try again.
E. The SD card can not save video recordings.
1. Make sure the SD card is FAT32 format. If you’re not sure, please use a computerto format the SD card. Or directly format it on the app->Device Settings->SD Card Record Config->Format.2. Please check on the app->Device Settings->SD Card Record Config->Make surethe Record option is not set to Record Off.
F. You can not receive any app pushing notification.
1. Please check on the app->Device Settings->Alarm Config->Make surethe Motion Detection Sensitivity and Push Notifications options are enabled.2. Check your phone settings: For Android: System Settings->Application->HDMINICAM->Notification-> Allow Notification. For iOS: Settings->Notification->HDMINICAM->Allows notification.
16
FAQ:G. How to change the resolution of recordings.
Please go to app->Device Settings->SD Card Record Config->Resolution.
H. The time stamp on video clips is not correct.
Please go to app->Device Settings->Time Setting->Sync With App Time.
I. The recordings on SD card has no sound.
Please go to app->Device Settings->SD Card Record Config->Turn on theSound Record option.
J. How to know whether the camera battery is full charged or not?
When the yellow indicated light is turned off automatically, that means the camerahas a fully charged.
K. The camera can not be powered off or restarted by pressing the Power button.
First of all, the correct operation of powering off camera is press and hold the Powerbutton for 3 seconds at least until you see all indicated lights are off. If this is not working, that means the camera’s program is crashed. Please use the pin tool to press the Force Shutdown button. See the details in page 4.
L. The live feed is dark and red, how to fix it?
This indicates the camera’s battery life is going to be dead. Please shut down the camera and plug in the power adapter to charge. Besides, please do a resetoperation before using it again. See page 4 to learn about how to reset the camera.
M. I can access camera in local network, but I can not access it from outside.
You need to check the router is Internet access firstly, sometime, the router mayblock the camera to access Internet, you can check if the camera is in the whitelistof router or take a try to restart the router. Next, you need to ensure your phoneis Internet access no matter your phone using cellular network or other WiFi network.
17
FAQ:N. How to disable the indicator lights?
Please go to app->Device Settings(Advance Config)->Misc Settings->Set the Work LED to OFF.
O. How to set camera record in schedule time?
Please go to app->Device Settings(Advance Config)->SD Card Record Config->Set Record option to Timing Record, then you will have two options to configurethe StartTime and EndTime.
P. The cam is still online after I press the Power button, the cam plugs with USB Charger.
The camera can’t be powered off when the USB charger is plugged. When the USBcharger is plugged, long-press the Power button will only turn off all indicator lights,the camera won’t shut down. Unless you take out the USB plug or use a pin tool topress Force Shutdown Button.
Q. When I plug in the SD card, the SD card won’t lock.
Please ensure the logo side of SD card faces down, push it in until it locks in place. If you already tried both side, please contact us.
R. Can you place the mini camera in area where has moisture?
The mini camera is non-waterproof, please don’t place it nearby water or any placehas moisture.
S. Where can you purchase the magnetic bracket?
You can browse our official website: www.titathink.com to buy.
FAQ:T. What is the default password of camera.
The default camera password is 8888. It can be found in the label on mini camera.
U. What is an eligible camera password for security privacy.
An eligible camera password must contain 8 characters at least. It should containcapital, lowercase letter, number and special characters like !@#$%^&*. Don’t usesimple password like ‘admin’, ‘123456’ or something contains repetitive letters.
18
www.titathink.com
support.titathink.com
Download the newest quick guide on support site:https://support.titathink.com/knowledgebase/download-pdf/
Support mail: [email protected]
Phone: +86 0775-8602-0195
Skype ID: titathink
Chat us: https://app.purechat.com/w/titathink-support
Address: 2/f., Co-talent Park
Liuxian Road, Ban’an District
ShenZhen
CN
Ver 2
