Anticorit 161/1 MIL PRF 16173E GRADE 1, Class 1

Fuchs Lubricants Co. 17050 Lathrop Avenue Harvey, IL 60426 Telephone: 708-333-8900 E-Mail info@fuchs.com http://www.fuchs.com

PRODUCT information

Product information is based on data obtained by our own research and is considered accurate. However, no warranty is expressed or implied regarding the accuracy of these data, or the results to be obtained from the use thereof. Seller shall not be liable for any loss or damage or liability resulting from the use of the product in the buyers manufacturing processes or in combination with other substances.

Description Anticorit 161/1 is a solvent-cutback, black, cold application which is used as it comes from the container. This product is designed for the protection of metals when exposed to outdoor weather conditions and for general purpose preservation, indoor or outdoor, with or without cover, for domestic and overseas shipment where a dry-to-touch film is required. Anticorit 161/1 is a solvent-dispersed compound which deposits a thin, black, hard but flexible continuous film. The solvent will normally evaporate from smooth surfaces, leaving a dry to handle coating in approximately four hours. The residual protective coating will adhere to metal surfaces without checking or flaking at temperatures as low as 0F. The product will retain its homogeneity after exposure to temperatures as high as 130F and as low as -40F. It will not cause pitting or etching of brass, cadmium, zinc, magnesium, aluminum or steel. Anticorit 161/1 may be applied by spraying, brushing, swabbing or dipping. The material to be coated must be degreased and free of any oils, greases or other foreign material.

Advantages / Benefits

For indoor or outdoor use

Provides protection when exposed to outdoor conditions

Dry-to-touch film

Excellent at high and low

temperatures

Will not pit or etch brass, cadmium, zinc, magnesium, aluminum or steel

Anticorit 161/1 MIL PRF 16173E GRADE 1, Class 1

Fuchs Lubricants Co. 17050 Lathrop Avenue Harvey, IL 60426 Telephone: 708-333-8900 E-Mail info@fuchs.com http://www.fuchs.com

PRODUCT information

Product information is based on data obtained by our own research and is considered accurate. However, no warranty is expressed or implied regarding the accuracy of these data, or the results to be obtained from the use thereof. Seller shall not be liable for any loss or damage or liability resulting from the use of the product in the buyers manufacturing processes or in combination with other substances.

Typical Chemical and Physical Properties

Property Method Data Color Black Viscosity (80F) 600-900 cps Bulk Density (lbs/gal 60F) 7.2 - 7.4 Film Thickness (dip at 77F) 3 mils Pour Point 20F (approximate) Flash Point 100F minimum Voc Max 3.35 lbs/gal Salt Spray (5%) ASTM B117 36 days 100% Relative humidity ASTM D-1748 40 days Weathering F.S. Meth 6151 50 Days Application Anticorit 161/1 is applied by dip, spray, or brush from 40F to 100F. Coverage (77F) 33 sq ft/gallon. Material Safety Data Sheets are available. Before handling, read Product Data Sheet and Material Safety Data Sheet for proper handling and health hazard information.

ANTICORIT 5009 Solvent Based Dry Film Corrosion Preventative

FUCHS LUBRICANTS CANADA LTD. Eastern Division

405 Dobbie Drive, P.O. Box 909, Cambridge, Ontario N1R 5X9 Telephone (519) 622-2040 Product information furnished is based on data obtained by our own research and is considered accurate. However, no warranty is expressed or implied regarding the accuracy of these data, or the results to be obtained from the use thereof. Seller shall not be liable for any loss or damage or liability resulting from the use of the product in the buyer's manufacturing process or in combination with other substances.

Description:

ANTICORIT 5009 is a very low odour solvent based dry film corrosion preventative for ferrous and non-ferrous metals. It passes 90 days in the Humidity Cabinet Rust Test (ASTM D-1748). When properly applied, this coating, is estimated to provide indoor rust free storage for over 1 year. ANTICORIT 5009 contains a highly refined odourless solvent in order to minimize odour. The waxy residual film is readily removed with an alkaline cleaner. Application:

ANTICORIT 5009 should be applied on dry parts. The mode of application may be by dip, spray, or brush. Typical Properties:

Appearance...................................clear light amber Odourlow

Flash Point (TCC) (C))...................54 Specific Gravity @15.6C................0.788

Residual Filmwaxy Barium..not present Storage and Handling:

This product should be stored at room temperatures. Gloves and safety glasses are recommended when handling chemicals. Please refer to the Material Safety Data Sheet for additional information. Rev. 12/06

# !&

'() *+,

-- .*+'/0121)

,++-'131) 44

5+'1) 6.

(SG 2S1O* 6IZ

!

"

#

$

$

%

Anticorit SV 7X Firm Film Outdoor Corrosion preventive for Long Term Protection

=

Technical Data (typical properties)

Appearance Dark amber liquid

Weight (lb./gal.) 7.01

Flash, F., TCC 140

Viscosity at 100 F (SUS) 43

Viscosity at 40 C (cSt) 3.1

Barium none Protection time years (Indoor) 3

Doc. No.: MkF 1901: Rev. 01/04

Anticorit SV 7X Firm Film Outdoor Corrosion preventive for Long Term Protection

=

Anticorit SV 7X is a firm film outdoor corrosion preventive for both ferrous and non-ferrous metals. It is intended to protect finished parts, machinery and other equipment during storage or shipment. Anticorit SV 7X is a solvent carried product that dries rapidly to a dark amber film. The film is resistant to condensed humidity, salt atmospheres, low temperature storage, general handling and light abrasion.

Features Tough impervious film Resistant to humidity and salt

atmospheres Fast drying

Benefits Resists damage from handling

and mild abrasion Excellent for protecting overseas

shipments Film sets up quickly

How to Use Anticorit SV 7X is applied as received without dilution by spray brush or dip. The film should be undisturbed while drying. The product should be applied in a well-ventilated area. Metal surfaces should be cleaned and dry before applying. A single coating is recommended. How to Clean Anticorit SV 7X films can be removed by solvent cleaning with petroleum distillates.

CPD 7056 Gun Drilling Fluid

FUCHS LUBRICANTS CANADA LTD.

Eastern Division 405 Dobbie Drive, P.O. Box 909, Cambridge, Ontario N1R 5X9 Telephone (519) 622-2040

Product information furnished is based on data obtained by our own research and is considered accurate. However, no warranty is expressed or implied regarding the accuracy of these data, or the results to be obtained from the use thereof. Seller shall not be liable for any loss or damage or liability resulting from the use of the product in the buyer's manufacturing process or in combination with other substances.

Description:

CPD 7056 is a heavy duty moderate viscosity fluid designed for gun drilling operations

on steel. CPD 7056 contains extreme pressure additives for extending tool life and to

facilitate part machinability.

Application:

CPD 7056 is recommended for deep hole drilling and other machining operations.

Typical Properties:

Appearance:..clear amber

Specific Gravity @ 15.6C:...................................0.960

Viscosity @ 40C (cSt):.........................................21

Flash Point (C):....................................................180

Storage and Handling:

Store at room temperature. Gloves and safety glasses are recommended when handling

chemicals. Please refer to the MSDS for additional information.

Rev. 03/12

EcoDraw HVE 1 Medium Viscosity Synthetic

Fuchs Lubricants Canada 405 Dobbie Drive Cambridge, ON Telephone: 519-622-2040 http://www.fuchs.ca

Product Information

Product information is based on data obtained by our own research and is considered accurate. However, no warranty is expressed or implied regarding the accuracy of these data, or the results to be obtained from the use thereof. Seller shall not be liable for any loss or damage or liability resulting from the use of the product in the buyers manufacturing processes or in combination with other substances.

How to Use Eco Draw HVE 1 is diluted with water to form clear solutions. Concentration: Severe 1:1 to 1:5 Medium 1:5 to 1:10 Light: 1:10 to 1:15 How to Clean Eco Draw HVE 1 films and light residues are readily cleaned from processed parts using mild alkaline cleaner solutions Typical Chemical and Physical Properties

Property Data Appearance Golden Yellow liquid Solids 63% Odor Characteristic Chlorine None Refractometer Factor 1.7 Material Safety Data Sheets are available. Before handling, read Product Data Sheet and Material Safety Data Sheet for proper handling and health hazard information.

EcoDraw HVE 1 Medium Viscosity Synthetic

Fuchs Lubricants Canada 405 Dobbie Drive Cambridge, ON Telephone: 519-622-2040 http://www.fuchs.ca

Pr