Micro-Mark #82871 Dremel Table Saw Belt#82871 BELT FOR DREMEL TABLE SAW INSTRUCTIONS FOR...
1
#82871 BELT FOR DREMEL TABLE SAW INSTRUCTIONS FOR INSTALLATION AND ADJUSTMENT BELT REMOVAL/INSTALLATION Unplug the saw from electrical outlet and remove any attachments from the table top. Lower blade fully. Turn saw upside down, resting it on its top. “Walk off” worn belt from the non-flanged arbor pulley while rotating the assembly. Place the new belt onto the flanged motor pulley first and then proceed to “walk on” the new belt. BELT ADJUSTMENT If the new belt is too loose or too tight when installed, adjust the motor position for optimum belt tension as follows: Locate the two 1/8” Allen screws which mount the motor, and loosen just enough to allow the motor to be moved. Position motor so that belt can rotate freely around the pulleys without slipping, then tighten the screws. Note: When moving the motor, it is essential that the motor remains aligned with the arbor assembly so that the belt will track straight and not rub against the flanges of the motor pulley, or run off of the arbor pulley. Belt deflection under moderate finger pressure should be approx. 3/8” between the pulleys. MM051508 THE SMALL TOOL SPECIALISTS 340 Snyder Avenue, Berkeley Heights, NJ 07922 Tech Support: 908-464-1094, weekdays, 1pm to 5pm ET www.micromark.com [email protected]
Transcript of Micro-Mark #82871 Dremel Table Saw Belt#82871 BELT FOR DREMEL TABLE SAW INSTRUCTIONS FOR...
#82871 BELT FOR DREMEL TABLE SAWINSTRUCTIONS FOR INSTALLATION
AND ADJUSTMENT
BELT REMOVAL/INSTALLATION
Unplug the saw from electrical outlet and removeany attachments from the table top. Lower bladefully. Turn saw upside down, resting it on its top.“Walk off” worn belt from the non-flanged arborpulley while rotating the assembly. Place the newbelt onto the flanged motor pulley first and thenproceed to “walk on” the new belt.
BELT ADJUSTMENT
If the new belt is too loose or too tight wheninstalled, adjust the motor position for optimum belttension as follows: Locate the two 1/8” Allen screwswhich mount the motor, and loosen just enough toallow the motor to be moved. Position motor so thatbelt can rotate freely around the pulleys withoutslipping, then tighten the screws.
Note: When moving the motor, it is essential that themotor remains aligned with the arbor assembly sothat the belt will track straight and not rub against theflanges of the motor pulley, or run off of the arborpulley. Belt deflection under moderate fingerpressure should be approx. 3/8” between the pulleys.
MM051508
T H E S M A L L T O O L S P E C I A L I S T S340 Snyder Avenue, Berkeley Heights, NJ 07922
Tech Support: 908-464-1094, weekdays, 1pm to 5pm ETwww.micromark.com [email protected]
#82871 BELT FOR DREMEL TABLE SAWINSTRUCTIONS FOR INSTALLATION
AND ADJUSTMENT
BELT REMOVAL/INSTALLATION
Unplug the saw from electrical outlet and removeany attachments from the table top. Lower bladefully. Turn saw upside down, resting it on its top.“Walk off” worn belt from the non-flanged arborpulley while rotating the assembly. Place the newbelt onto the flanged motor pulley first and thenproceed to “walk on” the new belt.
BELT ADJUSTMENT
If the new belt is too loose or too tight wheninstalled, adjust the motor position for optimum belttension as follows: Locate the two 1/8” Allen screwswhich mount the motor, and loosen just enough toallow the motor to be moved. Position motor so thatbelt can rotate freely around the pulleys withoutslipping, then tighten the screws.
Note: When moving the motor, it is essential that themotor remains aligned with the arbor assembly sothat the belt will track straight and not rub against theflanges of the motor pulley, or run off of the arborpulley. Belt deflection under moderate fingerpressure should be approx. 3/8” between the pulleys.
MM051508
T H E S M A L L T O O L S P E C I A L I S T S340 Snyder Avenue, Berkeley Heights, NJ 07922
Tech Support: 908-464-1094, weekdays, 1pm to 5pm ETwww.micromark.com [email protected]
#82871 BELT FOR DREMEL TABLE SAWINSTRUCTIONS FOR INSTALLATION
AND ADJUSTMENT
BELT REMOVAL/INSTALLATION
Unplug the saw from electrical outlet and removeany attachments from the table top. Lower bladefully. Turn saw upside down, resting it on its top.“Walk off” worn belt from the non-flanged arborpulley while rotating the assembly. Place the newbelt onto the flanged motor pulley first and thenproceed to “walk on” the new belt.
BELT ADJUSTMENT
If the new belt is too loose or too tight wheninstalled, adjust the motor position for optimum belttension as follows: Locate the two 1/8” Allen screwswhich mount the motor, and loosen just enough toallow the motor to be moved. Position motor so thatbelt can rotate freely around the pulleys withoutslipping, then tighten the screws.
Note: When moving the motor, it is essential that themotor remains aligned with the arbor assembly sothat the belt will track straight and not rub against theflanges of the motor pulley, or run off of the arborpulley. Belt deflection under moderate fingerpressure should be approx. 3/8” between the pulleys.
MM051508
T H E S M A L L T O O L S P E C I A L I S T S340 Snyder Avenue, Berkeley Heights, NJ 07922
Tech Support: 908-464-1094, weekdays, 1pm to 5pm ETwww.micromark.com [email protected]
