Micro Hi.Fi Component System - c.searspartsdirect.comYou can preset up to 20 FM stations and I0 AM...
Transcript of Micro Hi.Fi Component System - c.searspartsdirect.comYou can preset up to 20 FM stations and I0 AM...
S ON,g;. ,.239_02.,_,>
Micro Hi.FiComponentSystem
Operating Instructions
Owner's Record
The model and serial numbers are Ioealed al the rear. Record the serial number i]_the
space provided below. Ret_:r to them whenever you call upon your Sony dealer
regarding this product.
Model No. Serial No.
OlOffJO.. JUOIO
CMT-CPI01
© 2002 Sony Corporation
To prevent fire or shock hazard, do notexpose the unit to rain or moisture.
To avoid electrical shock, do no) open the cabinet.RefEr servicing to qualified personnel only.
Do not install the appliance in a confined space,such as a bookcase or built-in caNneL
Ct Jura I LallER PRCWJCT
UJOK_ 1 LASfRu_rm
_ I L&8_*_PAT
This appliance is classifiedas a CLASS 1 LASER
product. Tlds label islocated ml the rear exterior.
To prevent fire, do not cover the ventilation of tile
apparatus with news papers, table-cloths, curtains,etc. And don't place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on (he apparatus.
Don't throw away tile battery withgener_l house waste, dispose of it
correctly as chemical waste.
NOTICE FOR THE CUSTOMERS IN THEU*S.A*
r_Fm n_l_a 1o Qa_JRm n_ _t_nCL_E-
This symbol is intended to alert tile
user to the presence of uninsulated"dangerous voltage" within the
product's enclosure that may be ofsufficient magnitude to constitute a
risk of electrlc shock to persons.
This symbol is intended to alert tileuser to the presence of important
operating mid maintenance (servicing)instructions ill the literature
accompanying the appliance.
CAUTION
The use of optical instruments with this product will
increase eye hazard.
Note to CATV system installer:
This reminder is provided to cal! tile CATV systemins)aller's altention to Article 820-40 of the NEC thai
provides guidelines for proper grounding and, ill
particular, specifies thai the cable ground shall beconnected to the grounding system of (he building, as
close to the point of cable entl T as practical.
WARNING
This equipment has been tested and tbund to comply
with (he limits fPr a Class B digital device, pursuantto Part 15 of the ECC Rules. These limits are
designed to provide reasonable protection againstharmful intert_rence in a residential installation. This
equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in
accordance with tile instructions, may cause harmfulinterfi:rence to radio communicaHons. However,
there is no guarmltee tllal interference will not occurin a par ficular installation. I f this equipment doescause harnl|hl interference to radio or television
reception, which can be determined by turning the
equipment off and on, (he user is mlcouraged to try tocorrect the interiErence by one or more of the
following measures:
Reorient or relocate lhe receiving antenna.
Increase the separaHon belween the equipment andreceiver.
Connect the equipment into an outlet on a circuitdifferent from thai to which the receiver is
connected.
Consult the dealer or an experle_lced radio/TVtechnician tPr help.
CAUTION
YOU are cautioned that any changes or modifications
not expressly approved ill this manual could void
your authority to operate this equipment.
NOTICE FOR THE CUSTOMERS IN
CANADA
CAUTION
TO PREVENT ELECTRIC SItOCK, DO NOT USETHIS POLARIZED AC PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHEROUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.
Except for European models
ENERGY STAR * is a U.S.
registered mark.As an ENERGY STAR _¸partner,Sony Corporation has determined
that this product meets theENERGY STAR ®guidelines _r
energy efficiency.
2 GB
Sound Adjustment
Adjusting the sound ............................. 15Main unit ............................................... 4
Remote Control ..................................... 5 Display
Using the display ................................. 16Getting Started
Hooking Lipthe system .......................... 6 Other Features
Inserting two size-AA (R6) batteries into
the remote control ........................... 7
Setting the clock .................................... 7
CD
Falling asleep to music--_ Sleep Timer .............................. 16
Waking up to music.........Daily Timer .............................. 16
Loading the CD ..................................... 8
Playing the CD........NormalPlay/ShufflePlay/RepeatPlay.... 8
Programming the CD tracks........Program Play .............................. 9
Optional Components
Hooking up optional components ........ 18
Listening to audio from a connected
component ..................................... 18
Recording on a connected component ... 18
Tuner
Presetting radio stations ......................... 9
Listening to the radio ........................... 11
Using the Radio Data System (RDS)* .... 11
Troubleshooting
Problems and remedies ........................ 19
Additional Information
Tape Precautions .......................................... 21Specifications ...................................... 22
Loading a tape ..................................... 12Pl_ying a tape ...................................... 12 *Europeanmodelonly
Recording to a tape-- CD Synchro Recording/Recording M3nually/Progl_n Edit ... 13
Timer-recording radio programs ......... 14
3 GB
Illustration numberHOW to use this page
Use lhis page to lind the location of buttons and other PLAY MODE [] (9, 13, 14)
par_s of the system that are mentioned in the text. _ TName of button/part Reference page
I ALPHABETICAL ORDER I
BASS L_] (15)
CD EJECT "_ I_i_(g)
CD SYNC [_[!](13, 14)
CD _" I!_ (8, 9)
CD•[j[_](8 10,18,20)
CD I_1/),,IIH _j[_(8, 9)
CD _141 /I_H_ I][_ (8)
DSG [_] (15)
FUNCT1ON[_](8 10, 12, 13,18)
PHONES jack _
PLAY MODE [{7_(8, 9, 14)
Remote sensor _]
REPEAT [1[_(8)
Tv::TAPE EJECT _ [_] (12)
TAPE • REC [_] (13)
TAPE 41_ _] (1214)
TAPE || _ (1214)
TAPE • [_] (1214, 2O)
TAPE _1/),*_ [_] (!2)
TREBLE I__ (15)
TUNER BAND I_[_ (9, 10, 20)
TUNING MODE L}I_](91 i)
TUNING +/[!_ (9d I)
VOLU ME [_[] ( 17}
BUTTON DESCRIPTIONS ]
|/(_ (power)[[j[] (7, 10, 15, 17,
18)
4 GB
Follow steps [] through [] of the procedure below to hook up your system using tbe supplied cordsand accessories.
AM loop antenna
Q FM antenna
Right speaker Left speaker
[] Connect the speakers.
Connect the right and let'Espeaker cords to_lte SPEAKER terminals as shown below.
Solid ((_)
Stripe (8)
insert this portion
Jack type @Extend the FM wire AM loopantenna hodzontally antenna
[] Connect the FM end AM antennas.
Set the AM loop antenna up before
connecting it.
6 GB
Jack type ®
_._j Extend the FM,_#f_N wire antenna AM loop
horizontally antenna
I J
[] For models with a voltage selector, setVOLTAGE SELECTOR to the local
power line voltage.
110V-120V
220V-240V
VOLTAGE
SELECTOR
[] Connect the power cord to a wall outlet.
Iflhe plug does not fit the wall socket,
detach tl_e supplied plug adaptor (only for
models equipped with an adaptor).
To torn on the system, press I/Q).
1 Turn on the system.
2 Press TIMER SET on the remote.
3 Press I.q141/1_1 on the remote
repeatedly to set the hour.
4 Press ENTER on the remote.
The minute indic3fion flashes.
5 Press 14141/1_1_1on the remote
repeatedly to set the minute.
6 Press ENTER on the remote.
The clock will begin operating.
To adjust the clockI Press TIMER SET on the remote.
2 Press _ or _ on the remole to select
"SET CLOCK", then press ENTER on theremote.
3 Do the same procedures as step 3 to 6above.
a
ma
ao.
Tip
When tile remote no longer operates tile system,replace both batteries with new ones.
Note
If you do ]lot use the remote for a long period of time,_move tile batteries to p_vent possible damage from
battery leakage and corrosion.
7 GB
1 Press CD EJECT _.
The disc tray slides out.
2 Load a CD onto the disc tray.
Load with thelabel side up.When you playa CD single(8 cm CD),load it onto theinner cgcle of
the tray.
3 Press CD EJECT • again to close the
disc tray.
i Normal Play/Shuffle Play/RepeatPlay
This system lets you play CDs in different playmodes.
! r"l r"l
Track number Playing time
1 Press FUNCTION repeatedly until "CD"appears in the display.
2 Press PLAY MODE (or TUNING MODElPLAY MODE on the remote) repeatedlyuntil the mode you want appears in thedisplay.
Select To play
No display The CD in original order.
SHUFFLE The tracks on the CD in randomorder.
PGM The tracks on the CD in any
order that you want (see"Programming the CD tracks" on
page 9).
Press CD I_11 (or CD _ on the remote).
Other Operations
TO DO this
Stop playback Press CD m.
Pause Press CD _1t (or II on the
remote). Press again to
resume playback.
Select a track During playback or pause,
press CD I.I1_/mH_l
repeatedly until you find thedesired track.
Find a point in a track During playback, press andhold down CD _141/I_1_
until you find the desired
point.
Remove the CD Press CD EJECT _.
Play repeatedly
(Repeat Play)
Press REPEAT repeatedly
during playback until"REPEAT" or
"REPEAT I" appears in the
display.
REPEAT: For all the tracks
on the CD.
REPEAT 1 : For only the
currently playing track.
TO cancel playing
repe_ledly, press REPEAT
repe_ledly until "REPEAT"
and "REPEAT 1" disappear
from the display.
8 GB
-- Program Play
You can make a program of up to 24 tracks on
a CD in any order lhat you want.
1 Press FUNCTION repeatedly until "CD"
appears in the display.
2 Press PLAY MODE (or TUNING MODEl
PLAY MODE on the remote) repeatedlyuntil "PGM" appears in the display.
3 Press CD PI<I/IHH repeatedly until thedesired track number appears in thedisplay.
JSelected track Total playing timenumber
4 Press PLAY MODE (or TUNING MODElPLAY MODE on the remote).
The selected track is programmed.
The selection number appears in the
display.
5 To program additional tracks, repeatsteps 3 and 4.
6 Press CD _11 (or CD l=_ on the remote).
To Do this
Cancel Program Play Press PLAY MODE (orTUNING MODE/PLAY
MODE m_ the remole)
repeatedly until "PGM"
disappears t_om the display.
Add a track to the end Do steps 3 and 4 with
of the program Program Pl_y stopped.
Erase the entire Press CD • with Program
program Play stopped.
Tips
• The progrmn you made remains after Program Play
finishes. To play fl_e progrmn again, switch thethnction to CD, and then press CD I_ll (or CD
on the remote).
• "--.-J' appears in the display when the total programtime exceeds 100 minutes.
You can preset up to 20 FM stations and I0
AM stations. You can lhen tune in any oflhose
stations simply by selecting the corresponding
preset number.
There are lwo ways to store the station presets.
To Method
Automatically tune Automatic Tuning Presetall of the stations
that can be received
in your area and then
store them manually
Manually tune and s_ore Manual Tuning Preset
the radio tYequency of
your favorite stalions
Setting presets throughautomatic tuning
1 Press FUNCTION repeatedly until"TUNER" appears in the display.
2 Press TUNER BAND to select FM orAM.
3 Press TUNING MODE (or TUNINGMODE/PLAY MODE on the remote)repeatedly until "AUTO" appears in thedisplay,
4 Press TUNING +/- (or _1<1/1_1_on theremote),
The frequency changes as _e system scans
lbr a station. Scanning stops automatically
when a station is tuned in. At that time,
"TUNED" and "STEREO" (for stereo
program only) appear.
If "TUNED" does not appear and thescanning does not stop
Set the frequency of the desired radio
station as described in staps 3 through 7 of
"Setting presets fl_rough manual tuning'.
continued
O
9 GB
Presetting radio stations (continued)
S Press MEMORY on the remote.
A preset number flashes.
,nn _
Preset number Frequency
6 Press I_1_1/l_l on the remote
repeatedly to select the preset number
that you want.
7 Press ENTER on the remote.
The station is stored to the selected preset
number.
8 Repeat steps 2 through 7 to preset
other stations,
Tip
Press TUNING MODE (or TUNING MODE/PLAY
MODE on the remote) when you want to stopscanning.
Setting presets throughmanual tuning
1 Press FUNCTION repeatedly until"TUNER" appears in the display.
2 Press TUNER BAND to select FM orAM.
3 Press TUNING MODE (or TUNING
MODE/PLAY MODE on the remote)repeatedly until "AUTO" and "PRESET"disappear from the display.
4 Press TUNING +/- (or 4_1/1=-I_ on the
remote) repeatedly to tune in thedesired station.
5 Press MEMORY on the remote.
A preset number flashes.
IUI i
Preset number Frequency
6 Press I_P_/1=_-I on the remote
repeatedly to select the preset numberthat you want.
7 Press ENTER on the remote.
The station is stored to tbe selecled presetnumber.
8 Repeat steps 2 through 7 to presetother stations.
Other Operations
TO Do this
Tune in a station Follow tile procedure described in
with a weak "Setting presets through manual
signal tuning".
Stop setting Press TUNING MODE (or
presets TUNING MODE/PLAY MODE
on the remote).
To chm_ge the Start over from step 2.
preset number
To change the AM tuning interval
(Except for the European, Middle
Eastern and Philippine models)
The AM tuning interval is factory-preset to 9 kltz (or
I0 kHz tbr some areas). To change the AM tuninginterval, tune ill any AM slalion first, then turn offthesystem. Press and hold TUNING m_d CD II. When
you change the interval, all the AM preset stations areerased. To reset the interval, tune in any AM slalion
firsl, then turn off fl_e system. Press and holdTUNING andCD a.
Tips
• The preset s_ations are retained tbr _bout a day eveni f you disconnect the mains lead or if a powerPdilure occurs.
• TO improve the reception, adjus_ the suppliedamennas or connect an external antenna.
10 GB
You can listen to a radio station either by selecting a
preset station, or by manually tuning in fl_e station.
Listening to a preset station
-- Preset Tuning
Preset radio stations in the tuner's memory first
(see "Presetting radio stations" on page 9).
1 Press FUNCTION repeatedly until"TUNER" appears in the display.
2 Press TUNER BAND to select FM orAM.
3 Press TUNING MODE (or TUNING
MODE/PLAY MODE on the remote)repeatedly until "PRESET" appears inthe display.
4 Press TUNING +/- (or <t<l/l_l_ on the
remote) repeatedly to select the desiredpreset station.
Listening to non-preset radiostation
-- Manual Tuning
1 Press FUNCTION repeatedly until"TUNER" appears in the display.
2 Press TUNER BAND to select FM orAM.
3 Press TUNING MODE (or TUNINGMODE/PLAY MODE on the remote)repeatedly until "AUTO" and "PRESET"disappear from the display.
4 Press TUNING +/- (or <t<l/l_l_ on theremote) repeatedly to tune in thedesired station.
Tips
• To improve bmadcas_ reception, adjust the supplied
aerials, or connect a commercially awitableexcen_al aerial.
• When an FM stereo program has stalic noise, pressFM MODE repealedly until "MONO" appears.
There will be no stereo effect, but the reception willimprove.
• Press TUNING MODE (or TUNING MODE/PLAY
MODE m_ the remote) repeatedly until "AUTO"
appears in step 3 above, then press TUNING + /(or _/_ on the remote). The frequency
indicalion changes m_d scanning slops when €hesystem tunes in a station (Automalic Tuning).
(European model only)
What is the Radio Data
System?
Radio Data System (RDS) is a broadcastingservice that allows radio stations to send
additional intbm_adon along with the regular
program signal. RDS is available only on FMstadons.*
Note
RDS moy not work properly if the slolion you are
tuned in is not transmitting the RDS signal properlyor if the signal is weak.
* Not al! FM statim_s provide RDS service, nor dothey provide €he stone types of services. If you are
not t:amiliar with the RDS system, check with yourlocal radio stations for details on RDS services in
your area.
Receiving RDS broadcasts
Simply select a station from the FM band.
When you tune in a station lhat provides RDS
services, the station name appears in the
display.
To check the RDS information
Each time you press DISPLAY on the remote,
the display changes cyclically as follows:
Station name* -_ Frequency -4. Clock display
* If the RDS bm_dcasl is not properly received, thestation name m_y nol appear in the display.
€
ml
11 GB
1 Press TAPE EJECT _--.
2 Load a recorded/recordable tape intothe cassette holder.
With the side you want to play/record on facing towards you
@ o 0
Other Operations
TO DO this
Stop playback Press TAPE II.
Pause Press TAPE II (or II on the
remote). Press again to
resume playback,
Fast-_rward or With the tape stopped, pressrewind TAPE _</IH_.
Remove the tape P_ss TAPE EJECT --,_.
You can use Type I (normal) tape.
1 Load a recorded tape into the cassetteholder.
2 Press FUNCTION repeatedly until"TAPE" appears in the display.
3 Press DIR MODE on the remote
repeatedly to select "_' to play oneside of the tape, "_.._)" to play bothsides, or "C_-._)"* to play both sidesrepeatedly.
* The t_pe automatically stops after playing backfive times.
4 Press TAPE <1_.
Press TAPE <lit- again to play the reverse
side. The tape starts playing back.
12G_
-- CD Synchro Recording/Recording Manually/Program Edit
You can record fi'om a CD (or connected components) or radio. You can use Type I (normal) tape.
Recording from a CD3teps (CD Synchro Recording) Recording manually
1 Load a recordable tape into the cassette holder.
2 Load a CD onto the disc tray. Press FUNCTION repeatedly to selectthe source you want to record from.
Press FUNCTION repeatedly until "CD" Load a CD (or other music source), or3 appears in the display, tune in the desired station.
4 Press CD SYNC. Press TAPE • REC.
The tape stands by for recording.
"m" and "1_" (or "<') appear.
TO start recording on the side facing away from you, press TAPE <11_until "_Jal_"changes to "4BE."
Press DIR MODE on the remote repeatedly to select "3' to record on one side of5 the tape, or "_.._)" or "¢_.._)" to record on both sides.
6 Press TAPE II. Press TAPE II, and then start playingthe desired source.
To stop recording
Press TAPE II.
Tip
For recording manually:To pause recording, press TAPE II.
continued
13 GB
Recording to a tape (continued)
Recording CD tracks in yourfavorite order-- Program Edit
1 Load a recordable tape into thecassette holder.
2 Load a CD onto the disc tray.
3 Press FUNCTION repeatedly until "CD"appears in the display.
4 Press PLAY MODE (or TUNING MODE/PLAY MODE on the remote) repeatedlyuntil "PGM" appears in the display.
S Press CD Pq_I/bdH repeatedly until the
desired track number appears in thedisplay.
6 Press PLAY MODE (or TUNING MODE/PLAY MODE on the remote).
The selected track is programmed.
The selection number appears in the
display.
To program additional tracks, repeat steps 5and 6.
7 Press CD SYNC.
The tape stands by lbr recording and d_e CD
stands by fbr playback.
"m" and "l_" (or "'<") appear, and _l_e
CD SYNC indicator lights up.
To start recording on the side lhcing away
from you, press TAPE 41_ until "m_"
changes to "41ma."
8 Press DIN MODE on the remote
repeatedly to select "_' to record onone side of the tape, or "__._}" or "C_-._}"to record on both sides.
9 Press TAPE II.
TO Do this
Stop recording Press TAPE l.
Cancel Program Press PLAY MODE (orEdit TUNING MODE/PLAY
MODE on the remote)
repeatedly until "PGM"
disappears from tl_e display.
To place a specific number of tracks
on each side of the tape during CD
Synehro Recording
1 Program the tracks for the first side by
doing sleps 1 1o 6.
2 Press II on d_e remote.
3 Program the tracks tbr the od;er side by
doing staps 5 and 6.
4 Do sleps 7 to 9 (see Note below).
When the II command is detected during
CD Synchro Recording, d_e CD will pause,
the first side of the tape will continue
running till it ends, the tape will reverse
direction, the CD will play and recording of
the remaining tracks will resume on the
other side of the tape.
Note
To enable two-slded recording, you musl select"_-._3" or "C-_3" in step 8 on the ]ef_.
To timer_record, make sure 1hat you have set
the system clock correctly (see "Setting the
clock" on page 7) and preset the radio stafion
(see "Presetting radio stations" on page 9).
1 Tune in the desired preset radio station(see "Listening to the radio" on page11).
2 Load a recordable tape.
3 Press TIMER SET on the remote.
4 Press o. the remote
repeatedly until "SET REC" appears inthe display.
"SET RE(.'" scrolls and "@ REC" appears
in the display.
S Press ENTER on the remote.
"ON TIME" appears, then the hourindication flashes.
14 GB
6 Set the starting time.
Press I<1'</ b,'l_l on lhe remote repeatedly to
set the hour, lhen press ENTER on lheremote.
The minute indication begins flashing next.
Press I<1<1/ b,'l_l on the remote repeatedly to
set the minute, then press ENTER on the
remote.
"OFF TIME" appears, then the hour
indication flashes again.
7 Set the stopping time by repeating step6.
The start time, lhe slopping time,
"TUNER", and lhe preset station appear in
turn, then the original display returns.
8 Press I/(_ to turn off the system.
When the recording starts, the volume level
is aulomatically set to lhe minimum.
To DO this
Cheek the settings Press TIMER SELECT on the
remote repealedly until
"@ REC" appears in tile
display. The preset items
appear in turn.
Turn offthe timer Press TIMER SELECT on the
remote repealedly until
"@ REC" disappears fkom the
display.
Tip
Once you sel tile timer, tile time settings will remainin the system's memory until you change them, even
when you turn the system or the timer oft'. Thesettings that were lasl used wil! be in effect when you
turn the timer on again.
Notes
• The system will turin on 15 seconds betbrc the
specified slar ring time.
• Ifd_e system is turned on ot the specified starting
time, recording will no_ occur.
• When you have sel the Sleep Timer, the timerrecording will not operate until the Sleep TimerFunction is turned off.
• You cannot operate the Daily Timer and the timer
recording at the same time.
Generating a more dynamic sound
(Dynamic Sound Generator)
Press DSG.
To cancel the DSG, press DSG again.
Adjusting the bass
Turn BASS.
You can adiust the bass.
Adjusting the treble
Turn TREBLE.
You can adiust the treble.
oSf;l,
&
:l
to,l,
15 GB
Checking the remaining time(CD)
Press DISPLAY on the remote during play.
Each time you press tl_e button, tl;e display
changes cyclically as tbllows:
Current track number and elapsed playing timeof the track -_ Current track number and
remaining playing time of the lrack*
Remaining playing time oftl;e entire CD -_.
Clock display
* " " appears when you check the remainingpl_ying time ofa CD track whose number is 25 orover.
Checking the total playingtime (CD)
Press DISPLAY on the remote in stopmode.
Each time you press tl_e button, tl_e display
changes cyclically as fbllows:
Total playing time --* Clock display
Current source display
i Sleep Timer
The Sleep Timer Function lets you specific a
sleep time, al_er which the system stops playing
and turns offautomatically. You can thus fMlasleep to music.
Press SLEEP on the remote repeatedly.
The sleep time changes as tbllows:
AUTO* -_ 90MIN _ 80MIN --* 70MIN
... --+ 10MIN --* OFF --* AUTO* -_ ...
* The system turns off aider the current CD or t_pefinishes playing (up to 10fi minutes). The systemalso turns off when you manually stop the CD ortape.
TO Press
Check the remaining SLEEP on the remote once.
sleep time**
Change the sleep time SLEEP on the remote
repealedly until the time
you want appears.
Cancel the Sleep SLEEP on the remote
Timer Function repealedly until "OFF"
appears.
** You cannot check the remaining time if you select"AUTO".
i Daily Timer
By setting the Daily Timer, you can make thesystem amomatically turn on and offat
specified times. To use tllis function, make
sure that you have set tl_e system clock
correctly (see "Setting the clock" on page 7).
16 G_
1 Prepare the music source you want tolisten to when the system turns on.
• CD: Load a CD. To start playing from a
specific track, make a program (see
"Programming lhe CD tracks" on page 9).
• Tape: Load a tape with the side you want
to play facing towards you.
• Radio: Tune in the preset radio station
that you want (see "Listening to the radio"
on page 11 ).
2 Adjust the volume.
3 Press TIMER SET on the remote.
4 Press I<t<I/IHH on the remote
repeatedly until "SET DAILY" appearsin the display."SET DAILY" scrolls and "@ DAILY"
appears in the display.
5 Press ENTER on the remote.
"ON TIME" appears, lhen the hourindication flashes.
6 Set the starting time.
Press _/1_1 on lhe remote repeatedly to
set the hour, lhen press ENTER on lhe
remote.
The minute indication begins flashing next.
Press _/1_1 on the remote repeatedly to
set the minute, then press ENTER on lherenlote.
"OFF TIME" appears, 1hen the hour
indication flashes again.
7 Set the stopping time by repeating step6.
8 Press I<I<I/IHH on the remote
repeatedly until the music source youwant appears.
The display changes as lbllows:
9 Press ENTER on the remote.
The starting time, 1he stopping time, and the
music source appear in turn, lhen the
original display returns.
10PressI1_ to turn off the system.
To DOthis
Cheek the settings Press TIMER SELECT on the
remote repeatedly untl]
"@ DAILY" appears in thedisplay. The preset itemsappear in turn. N
Turn offthe timer Press TIMER SELECT on the
remote repeatedly untl]
"@ DALLY" disappears from @
the display. 'tl
€
Tip
Once you sel tile timer, tile tinle settings will remainin the system's memory unt!l you change them, even
when you turn the system or the timer off. Thesettings that were lasl used wil! be in ettkct when you
turn the timer on again.
Notes• The system will tunq on 15 seconds betbre the
specified sla_ing time.• When you have sel the Sleep Timer, the Daily
Timer will not operate until the Sleep TimerFunction is tllrned off.
• You canlm_operate the Daily Timer and the timerrecording at the same time.
17 GB
To enhance your system, you can connect optional components. Refer to the operating instructions
provided with each component.
MD deck / VCR MD deck
/
From the audio output ,_
E
To the digital input jack ofan MD deck
[] AUDIO IN (MDNIDEO)jacks
Use audio cords (not supplied) to connect an
MD deck or VCR m (hese jacks. You can (hen
listen m analog audio fi_om the MD deck or
VCR through this system.
[] OPTICAL DIGITAL OUT (CO)jack
Use a digital optical cable (square, not
supplied) to connect an MD deck to lhis jack.
You can lhen output the digital audio to (he
MD deck fi_om INs system. If the jack is
covered with a cap, remove it before use.
1 Connect the audio cords.
2 Press FUNCTION repeatedly until "MD"or "VIDEO" appears.
Start playing the connected component.
Tip
If you cannot select "VIDEO" by pressingFUNCTION repe_ledly, turn off)he syslem and then
press CD • and FUNCTION at the same time. Thefunction will chm_ge f?om "MD" to "VIDEO", and"VIDEO" will appear in the display. To change back
to "MD", repeal this procedure.
18 GB
1 Connect the digital optical cable.
2 Start recording.
Re_r to the operating instructions provided
wilh connected component.
Shouldyouencounteraproblemwithyoursystem,dothetbllowing:1Makesurethepowercordandspeakercords
arecorrectlyandfirmlyconnected.2Findyourprobleminthetroubleshooting
checklistbelowandtakelheindicaledcorrectiveaction.
Iflheproblempersistsafterdoingalloflheabove,consultyournearestSonydealer.
General
There is no sound from the speakers.
• Adjust the volume.
• The headphones are connected.
• Check the speaker connections.
There is severe hum or noise.
• A TV or VCR is placed too close to the unit.
Move the unit away from the TV or VCR.
"O:00" (or "AM 12:00") flashes in the display.
• A power inteiTuptlon has occurred, get _]le clock
(see page 7) and timer settings (see pages 14 and
16) again.
The timer does not function.
• Make sure the clock is correctly set (see page 7).
"@ DALLY" and "@ REC" do not appear when
you press TIMER SELECT on the remote.
• Make sure each timer is con'ecfly set (see pages
14 and 16).
• Make sure the clock is correctly set (see page 7).
The color on the TV screen is irregular.
• Move the speakers Parther away from the TV set.
The remote does not work.
• There is an obstacle between the remo_e and the
unit
• You are not pointing _he remote in the direction
of the syslem's sensor.
• The batteries in the remo_e have run down.
Replace the batteries.
• Make sure that the batteries are inserted
corrccdy.
Speakers
Sound comes from only one channel, or the left
and right volumes are unbalanced.
• Check the speaker connections and placement.
CD Player
The CD will not play.
• The CD is dirty.
• The surt:ace of the CD is scratched. Replace the
CD.
• The CD is loaded with the label side down.
• Condensation has buih up in the system.
Remove the CD and leave the system turned on
for about an hour until the moisture evaporates.
Play does not start from the first track
• The player is in Program or Shuffle Play. Press O
PLAY MODE (or TUNING MODE/PLAY "o
MODE on the remote) repeatedly until "PGM" _'
and "SHUFFLE" disappear
O
STape Deck
Recording cannot be done.
• There is no tape in the cassette holder.
• The record protect tab has been removed t¥omthe cassel_e (see page 21 ). II
17• The tape has come to the end. _'
The tape does not record or play, or there is a o="
decrease in sound level. 6.
• The heads are dirty. Clean them (see page 21).€I1
• The record/playback heads are magnetized.
Demagnetize them (see page 21 ).
The tape does not erase completely.
• The record/playback heads are magnetized.
Demagnetize them (see page 21 ).
There is excessive wow or flutter, or the sound
drops out.
• The capstans or pinch rollers are dirty. Clean
them (see page 21).
Noise increases or the high frequencies are
missing.
• The record/playback heads are magnetized.
Demagnetize them (see page 21 ).
continued
19 GB
Problems and remedies (continued)
Tuner
There is a severe hum or noise ("TUNED" or
"STEREO" flashes).
• Adjust the antenna.
• The signal strength is too weak. Connect aneXt _ITIal an{enna.
• Make sure that tile antenna is connecled
properly.
• Do not bend or roll up the antenna.
• The two wires comprising the FM amenna have
been pulled thrther apart since the syslem was
first purchased. Repair or replace with a new
One.
• The AM antenna wire is detached from the sland.
• Keep the antennas as Par away t¥om the speaker
cords as possible.
A stereo FM program cannot be received instereo.
• Press FM MODE on tile remote until "STEREO"
appears in the display.
Resetting the system
With the system turned on, press TAPE I,CD • and TUNER BAND at the same time.
The system is reset lo the tgctory settings. All
previous selrings are cleared and must be set
again.
Messages
One of the fbllowing messages may appear or
flash in the display during operations.
NO DISC
• There is no CD on tile disc tray.
PGM FULL
• You try to program 25 tracks or more.
PROTECT
• Consult your nearest Sony dealer.
20 GB
On operating voltage
Before operating tile system, check that the operatingvoltage of your system is identical with the voltage of
your local power supply.
On safety• The u]lit is not disconnected from the At-' power
source (mains) as long as it is connected to the walloutlet, even if the unit itself has been turned ot'_]
• Unplug the system from the wall outlet (mains) if itwill not be used tbr an extended period of time. Todisconnect the power cord (mains lead), pull it out
by the plug. Never pull file cord itsel£
• Should any solid ol_ject or liquid t:all into the
system, unplug the system and have it checked byqualified personnel before operating it any thrther.
• AC power cord must be changed only al thequalified service shop.
On placement
• Do not place the system in an inclined position.
• Do not place the system in locations where it is:
Extremely hot or cold
Dusly or dirty
Very humid
Subject to vibrations
Subject to direct sunlight
• Use caution when placing the unit or speakers on
surfaces that have been specially trealed (wgh wax,oil, polish, e_c.) as s_aining or discoloraion of the
surface may result.
On heat buildup
• Altllough _he unit heats up during operation, this isnot a malfmlction.
• Place the system in a location wgh adequale
ventilation to prevent heal build-up in the system.
If you continuously use this system at a large volume,
the cabinet temperature of the top, side and bottomrises considerably. To avoid burning yourself; do noltouch the cabinet.
To prevent a malfunction, do not cover the ventilation
hole for the cooling fan.
On operation
• If tile system is brought directly t?om a cold placeto a warm place, or is placed in a very damp morn,
moisture may condense on _he lens inside the CD
player. Should this occur, _he system will notoperate properly. Remove the CD and leave the
system turned oil for about an hour until themoislure evaporates.
• When moving the unit, remove any disc tllal may beon the disc tray.
If you ]lave any quesfimls or problems concerningyour system, please consult your nearest Sony dealer.
Notes on CDs
• Before playing a CD, clean the CD sur£ace with a
cleaning cloth. Wipe the CD fkom _he center out.
• Do not play a CD with tape, stickers, or adhesiveson any of its surfaces as this may dumage the
system.• Do not use solvents.
• Do not expose the CDs to direct sunlight or healsources.
• Disc with non-standard shapes (e.g., heart, square,
slat') cannot be played on this system. Attempting
to do so may damage tbe syslem. Do nol use suchdiscs.
Cleaning the cabinet
Clean tile cannel, panel and conirols with a soft c]otllslightly moislened with mild delergent solution. Do
not use any type of abrasive pad, scouring powder orsolvent such as thinner, benzene or alcohoh
To save a tape permanently
TO prevent a t_pe from being accidentally recordedover, break offtbe cassette tabs f?om side A or side Bas illustrated.
_, Break off the
cassette tab _ t_'
- e:.,i
Before placing a cassette in the tape
deck
Take up any slack in the t_pe. Otherwise the tapemay get entangled in the tape deck's playing
mechanism and become damaged.
If you later want to reuse the tape _be recording, cover
the broken tab with adhesive tape. ._
O.,i
When using a tape longer than 90
minutes
Tile tape is very elastic. Do not change the tapeoperations such as play, stop, and _hst-winding etc.
too f?equently. The tape may get entangled in thetape deck's playing mechanism.
Cleaning the tape heads
Clean tile t_pe heads after every 10 hours of use.Make sure to clean the tape heads before making a]_
important recording or after playing an old tape. Usea commercially available dry-type or wet4ype
clea]ling cassette. For delails, retkr to the instructionsof the cleaning cassette.
Demagnetizing the tape heads
Demagnelize the tape ]leads and the metal parts thathave contact wgh the tape after every 20 _o 30 hours
of use with a commercially available demagnetizingcassette. For details, reIkr to the inslructions of the
demagnetiTing cassette. 21GB
Amplifier section
For the U.S. model
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 6-ohm loads, both channels driven, from
70 - 20,000 tlz; rated 18 watls per channel
minimum RMS power, wilh no more 1hart 0.9%total harmonic distortion from 250 milliwalts to
raled output.
North American model:
Continuous RMS power output (reference):35+35W
(6 ohms at 1 kllz, 10%THD)
Total harmonic distortion less than 0.07% (6 ohms atI kllz, 18W)
European model:DIN power output (rated): 30 + 30 W
(6 ohms at 1 kHz, D1N)Continuous RMS power output (reference):
35+35W
(6 ohms at 1 kltz, 10%TIID)
Music power output (rethrence):85+85W
Other models:
The/bl!owing measured st 230 V AC, 60 Hz
DIN power omput (rated): 27 + 27 W(6 ohms at 1 kHz, D1N)
Continuous RMS power output (reference):32+32W(6 ohms at 1 kHz, 10%THD)
The/bl!owing measured st 220 V AC, 60 ItzDIN power oulput (rated): 23 + 23 W
(6 ohms at 1 kHz, DIN)Continuous RMS power output (reference):
26+26W
(6 ohms at 1 k]lz, 10%TItD)
InputsAUDIO IN MD (VIDEO) (phone jacks):
Sensitivily 500/250 mV,impedance 47 kilohms
OutputsOPTICAL DIGITAL OUT (CD):
OpticalPHONES: Accepts headphm_es with
an impedance of 8 ohmsor more
SPEAKER: 6 ohms
CD player section
System Compact disc and digitalaudio system
Laser Semiconductor laser
(_. 780 nm)Emissionduration: continuous
Wavelength 780 - 790 nmFrequency response 2 Hz - 20 kHz 00.5 dB)
Tape player section
Recording system 4-track 2-channel stereoFrequency response 50 - 13,000 ltz 03 dB),
using a Sm_y TYPE Icassette
Wow and flutter :J0.15% W. Peak (IEC)
0.1% W. RMS (NAB):_0.2% W. Peak (DIN)
Tuner section
FM stereo, FM/AM supefl_etero@_e tuner
FM tuner section
Tuning _ngeNorth American model:
Olher models:
87.5 - !08.0 MHz
(1 fl0-kltz step)87.5 - 108.0 MHz
(5fl-kHz step)FM wire m_tenna75 ohms unbalanced
10.7 MHz
Antenna
Antenna terminals
Inlennediale f?equency
AM tuner section
Tuning rangePan-American model: 530- 1,710 kHz
(with the tuning intervalset at 10 kHz)531 - 1,710kHz(with the tuning intervalset at 9 kHz)
European model: 531 - 1,602 kHz(with the tuning intervalset at 9 kHz)
Middle Eastern and Philippine models:531 - 1,602 kHz(with the tuning intervalset st 9 kHz)
Olher models: 530- 1,710 kHz(with the tuning intervalset _t 10 kilT)531 - 1,602 kHz(with the tuning intervalset at 9 kltz)
Antenna AM loop antenna, externalantenna terl_lilla]
Inlennediale fkequency 450 kHz
22GB
Speakers
Speaker system
Speaker units
R_led impedanceDimensions (w/h/d)
Mass
Two-way, bass reflex
systemI I cm dia., cone lypewoofer
2.5 cm dla., semi-dome-
type tweeter6 ohms
Approx. 154 x 252 x230 mm
Approx. 2.5 kg net perspeaker
General
Power requirementsNorth Americm_ model:
European model:Australian model:Mexican model:Other models:
120 V AC, 60 ltz230 V AC, 50/60 Hz230 V AC, 50/60 Hz120 V AC, 60 HzII0+ 120 V or220-240 V AC, 50/60 Hz
Adjustable with voltageselector
Power consumption
European model:
Othermodels:
See _he nameplate0.5 W (in the slandbylllode)
See the nameplate
Dimensions (w/h/d) Approx. 190 x 252 x340 mm incl. projectingparts and controls
Mass Approx. 5.6 kg
Supplied accessories Remote commm_der (l)
AM loop antenna ( 1)FM wire anlenna (1)B_tteries (2)
Design and speci flcalions are subject to changewithout no+ice.
O,,i
wl
3t0
O,,i
23 GB
Sony Corporation Printed in Korea http:/hwvw.sony.net]