MICHELLE - CSS · MICHELLE - CSS Disc LED Luminaire Direct/ Indirect and Direct CSS - Cable...
Transcript of MICHELLE - CSS · MICHELLE - CSS Disc LED Luminaire Direct/ Indirect and Direct CSS - Cable...
Birchwood Lighting • 3340 E. La Palma Avenue • Anaheim, CA 92806 714.550.7118 fax 714.550.7151
Due to a program of continuous improvement instructions are subject to change without notice.
© 2018 Birchwood Lighting, Inc. All rights reserved.29
Note: To be installed by a qualified electrician per N.E.C. and all local codes.
INSTRUCTION SHEET
J-BOX(By others)
J-BOXBRACKET BAR8-32 BRACKETBAR SCREWS
CANOPY
CANOPY
MOUNTINGCOUPLER
AIRCRAFT CABLE
3-O or 4-0 MUD RING(By others)
CABLE GRIPPER/CANOPY
MOUNTING STUD
NC - NO CANOPY
STND - 5” CANOPY
CABLELENGTH
1/4-20 STUD BY OTHERS
SIDE EXIT CABLE
GRIPPER
POWER CORD
STRAIN RELIEF
MICHELLE - CSS Disc LED LuminaireDirect/ Indirect and Direct
CSS - Cable Suspended
1. See below for J-Box mounting centers(Jbox by others) Assure that all j-boxes are properly mounted to structure and grounded.2. Secure bracket bar to mud ring for cable next to power drop. All other cable should be attached ¼-20 stud to structure and install cable gripper. NC (No Canopy) option is available for none power cables.3. Raise fixture up and insert cables into cable grippers and adjust to desired length. 4. Insert AWM cord through canopy and secure with provided strain relief.5. Trim off excess cable, be careful not to fray.6. Complete wire make-up in J-box7. Install canopy with canopy mounting coupler.
Servicing is while fixture is suspended1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.2. Slide spring latch to hinge down each liner half. 3. You will have access to all drivers behind liner.4. Reassemble by following 1 and 2 steps in reverse.
Adjusting lens drop1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. 2.Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.3. Select slot, raise and twist to lock into place.
MOUNTING CENTERS
4’ NOMINAL DIAMETER
2’ NOMINALDIAMETER
3’ NOMINALDIAMETER
28.00” B.C.
19.80”
15.58”
Ø18.00” B.C.
8.660
Ø10.0 B.C.
POWER FEED
1”
Power Feed
Power Feed
Power Feed
MOUNTING CENTERS
MOUNTING CENTERS
820-00150 V-0419
Birchwood Lighting • 3340 E. La Palma Avenue • Anaheim, CA 92806 714.550.7118 fax 714.550.7151
Due to a program of continuous improvement instructions are subject to change without notice.
© 2018 Birchwood Lighting, Inc. All rights reserved.27
Note: To be installed by a qualified electrician per N.E.C. and all local codes.
INSTRUCTION SHEET
Michelle - SM Circular LED LuminaireDirect or Dr/ In
SM - Surface Mount
1. See appropriate Stand Alone drawing for mounting locations. 1/2” lags and washer should be attached to framing.2. Remove Lens and unlatch LED liners and hinge down to acess mounting holes and drivers. 3. J-box and 4S mud ring (By others) should be centered over fixture to line up with power hole, 1” off center.4. Support Fixture near ceiling, bring wires through power hole into fixture. 4. Complete wire make-up in fixture. 5. Use 1/2” lag screws with appropriate washer to attach fixture to structure through mounting holes specified on drawing.6. Reinstall led liners.7. Install lens by grasping the fixture with one hand and rotating the lens clockwise with the other hand until it “clicks”. Once this occurs lens will float slightly but cannot fall out.
Servicing is while fixture is suspended1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.2. Slide spring latch to hinge down each liner half. 3. You will have access to all drivers behind liner.4. Reassemble by following 1 and 2 steps in reverse.
Adjusting lens drop1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. 2.Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.
STUD SPACING*see appropriate drawing
Insert lagsand twist
820-00151V-0419
Liner Release
Drop Lens Flush Lens
Counter Clockwise - RemoveClockwise - Install
Birchwood Lighting • 3340 E. La Palma Avenue • Anaheim, CA 92806 • 714.550.7118 fax 714.550.7151
28
Note: To be installed by a qualified electrician per N.E.C. and all local codes.
INSTRUCTION SHEET
48" MICHELLE
28.00” B.C.
19.80”
Ø1.000
.5621.250
REQUIRES 1/2” LAG BOLTS / WASHERS
4 5/16”
POWER FEED
1”
15.58”
Ø18.00” B.C.
36" MICHELLE
POWER FEED
1”
Ø1.000
.5621.250
REQUIRES 1/2” LAG BOLTS / WASHERS
8.660
Ø10.0 B.C.
POWER FEED
1”
Ø1.000
.5621.250
REQUIRES 1/2” LAG BOLTS / WASHERS
24" MICHELLE J-BOX(By others)
J-BOXBRACKET BAR8-32 BRACKETBAR SCREWS
CANOPY
CANOPY
MOUNTINGCOUPLER
AIRCRAFT CABLE
3-O or 4-0 MUD RING(By others)
CABLE GRIPPER/CANOPY
MOUNTING STUD
NC - NO CANOPY
STND - 5” CANOPY
CABLELENGTH
1/4-20 STUD BY OTHERS
SIDE EXIT CABLE
GRIPPER
POWER CORD
STRAIN RELIEF
MICHELLE - SM Circular LED LuminaireDirect or Dr/ In
SM - Surface Mounting Centers
Birchwood Lighting • 3340 E. La Palma Avenue • Anaheim, CA 92806 714.550.7118 fax 714.550.7151
Due to a program of continuous improvement instructions are subject to change without notice.
© 2018 Birchwood Lighting, Inc. All rights reserved.31
Note: To be installed by a qualified electrician per N.E.C. and all local codes.
INSTRUCTION SHEET
Adjustable Aircraft Cable
Mono Bracket Bar
Aircraft Cable
8/32 Bracket Bar Screws
J-Box w/ 3-0 or 4-0Mud ring(By Others)
Mono Point Coupler
CanopyAircraft Cable
Side Blocking
MICHELLE - CSS MONODisc LED LuminaireDirect/ Indirect and Direct
Mono CSS - Cable Suspended
1. Install Jbox (by others) Assure that all j-boxes are properly grounded. 2. Support the J-box with side blocking3. Screw to side blocking structure(By others)4. Secure bracket bar to mud ring.5. Run 3 cables through the Mono Point Coupler 6. Screw threaded rod into Mono Point Coupler.7. Screw 2 provided chrome couplers on thread rod8. Slide canopy over thread rod and coupler9. Screw theaded rod into bracket bar10. Raise fixture and feed 3 cables coming out of mono coupler into each adjustable cable gripper sticking out of the top lens of of fixture.11. Adjust fixture to desired height and level out with cable grippers. Trim excess cable.12. Insert AWM cord up through the hole in the canopy, into J-box. 13. Complete wire make-up14. Install canopy with magnets to bracket bar.15. Secure power cord with provided strain reliefs.
Servicing is while fixture is suspended” 1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.2. To release the liner, slide spring latch to hinge down each liner half. (24” uses thumb screws)3. You will have access to all drivers behind liner and keyholes for surface mounting.4. Re-assemble by following 1 - 3 steps in reverse.
Adjusting lens drop1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. 2.Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.3. Select either flush or drop lens slot, raise and twist to lock into place.*See next page for illustrations
820-00152V-0419
Birchwood Lighting • 3340 E. La Palma Avenue • Anaheim, CA 92806 • 714.550.7118 fax 714.550.7151
30
Note: To be installed by a qualified electrician per N.E.C. and all local codes.
INSTRUCTION SHEET
Liner Release
Drop Lens Flush Lens
Counter Clockwise - RemoveClockwise - Install
MICHELLE Disc LED LuminaireDirect/ Indirect and Direct
Fixture access for installation/service
Servicing/ Installing Fixture1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.2. To release the liner, slide spring latch to hinge down each liner half. (24” uses thumb screws)3. You will have access to all drivers behind liner and keyholes for surface mounting.4. Re-assemble by following 1 - 3 steps in reverse.
Adjusting lens drop1. Two people are required to remove bottom lens, one on each side of the fixture, performing the same task at the same time. 2.Grasp the fixture with one hand and rotate the lens counterclockwise with the other hand until it “clicks”. The Lens will drop free.3. Select either flush or drop lens slot, raise and twist to lock into place.