MFB-2 Template Plans
Transcript of MFB-2 Template Plans
to.
the fuselage. Doing so can cause EXTREME BODILY HARM if any hand or body part comes into contact with the fast spinning propeller. ·All minors should fly under the supervision of an adult or guardian.
Wingspan: 41.5 Inches Motor: 2212/6 or Higher Brusless Outrunner ESC: 30 AMP or Higher Brushless ESC
Prop: APC 6x4Battery: 2100mAH 3S (30C or Higher Lipo)
Servos:
Core Fan Fold Foam to build this plane too.Board. It should be possible to use Depron Foam or Blue plane was originally designed to be built from Foam materials, motor, battery and electronics used. This
: Weight and top speed may vary depending on Note
: 65mph to 90+ (Depending on Power System)
(Contact MESA rcFoamFighters at: [email protected])information or instructions.be Sold, or Altered to remove theMESA rcFoamFighters contact at local copy houses for personal use only. This plan may not MESA rcFoamFighters grants permission for this plan to be copied
Top Speed: 8.5 Inches from Nose of of plane.Center of Gravity
: 24 OuncesWeight: 19.5 InchesLength
(2.4ghz preferred) Any 4-channel or better Radio and Reciever:
2 Metal Gear
Disclaimer (Please Read)·This is a design template for a high performance, high speed RC aircraft. This plane should only be built and flown by experienced pilots with adequate skill to fly fast, maneuverable planes. ·DO NOT fly this plane where it can endanger people, livestock or property. ·ANY PERSONS DECIDING TO BUILD AND FLY THIS PLANE DOES SO AT HIS/HER OWN RISK AND LIABILITY. RCFOAMFIGHTERS ASSUMES NO RESPONSIBILITY FOR THE PERFORMANCE OF THIS PLANE. ·This plane should only be launched via the side launch method. Do not attempt to launch from the top or bottom of
Motor mount without brackets, you can alter this to fit your power systemif need
SolidWorks Student LicenseAcademic Use Only
PRINT ALL TEMPLATE SHEETS. CUT AND ASSEMBLE AS SHOWN INSTRUCTIONS:
BELOW. USE SCOTCH TAPE TO SECURE SHEETS TOGETHER.
(RC Model Airplane Construction Plans)MESA rcFoamFighters Team
MFB-2 Basic PlanTemplate(Design by Ken Tanpinco Revisions by Cody Lightbody)
(CAD Drawing by Jake Marshall)(Template Rev 1.0 - Copyright MESA rcFoam Fighters)
SolidWorks Student LicenseAcademic Use Only
(Template Rev 1.0 - Copyright MESA rcFoam Fighters)(CAD Drawing by Jake Marshall)
(Design by Ken Tanpinco Revisions by Cody Lightbody)
(RC Model Airplane Construction Plans)MESA rcFoamFighters Team
MFB-2 KFM4 and Parts Placement
NOTE: KFM4 Airfoil Placement is 50% of Main Wing, Include Elevrons.
Center of Gravity 8 1/2 inches
This Includes the KFM4From Nose of Plane
SolidWorks Student LicenseAcademic Use Only
(Contact MESArcFF at: [email protected])(All proceeds go to the students of MESA rcFoam Fighters)
CENTER STABILIZER
LEFT STABILIZER
RIGHT STABILIZER
MESA rcFoam FightersMFB-2 Basic Template(Design by Ken Tanpinco - 2010 )(Revised by Cody Lightbody - November 2011 Rev 1.0 )(CAD Drawing by Jake Marshall and Cody Lightbody - November11)(Basic Template release 1.0 - Copyright MESA rcFoam Fighters)
Copyright MESA rcFoam Fighters(MFB-2)
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only
CENTER SUPPORT BOTTOM PIECE
SolidWorks Student LicenseAcademic Use Only
MOTOR BRACKET
MOTOR BRACKET
Motor Bracket
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only
Cut Seen Here in the(Isometric View )
Double 45DEG Bevel Then Fold on ...
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only
NOTE: Drag Spacer Placement Seen HereNOTE: Drag Spacer Placement Seen Here
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only
Cut Notches For Right Stabilizers On This Side
SolidWorks Student LicenseAcademic Use Only
centerline, fold over main wing piece.
NOTE: Make a cut down the center of the airfoil, bevel both sides along
SolidWorks Student LicenseAcademic Use Only
centerline, fold over main wing piece.
NOTE: Make a cut down the center of the airfoil, bevel both sides along
SolidWorks Student LicenseAcademic Use Only
Battery Cut Out
SPEED.
ANGLE.
PIECES. THESE ARE
RECOMMENDED
NOTE: DRAG SUPPORT
SET AT THE
NOTE: INCREASING ANGLE = DECREASE IN SPEED. DECREASING IN ANGLE = INCREASE IN
Battery Cut Out
SolidWorks Student LicenseAcademic Use Only
Prop Cut Out
Battery Cut Out
Battery Cut Out
Prop Cut Out
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only
SETUP ELEMENTS.
NOTE: THERE IS NO EXACT PLACEMENT OF AIRDUCTS. POSITION THEM TO FIT POWER
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only
Cut Notches For Right Stabilizers On This Side
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only
CENTER SUPPORT TOP PIECE
Cut Notches For Motor Bracket On This SIde
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only
FUSELAGE TOP PIECE
FUSELAGE TOP PIECE
FUSELAGE TOP PIECE
FUSELAGE TOP PIECE
NOTE: Make small cuts into paper of foam board to achieve desired curve
of fuselage.
SolidWorks Student LicenseAcademic Use Only
SolidWorks Student LicenseAcademic Use Only