MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick...

11
13 October 2011 1 MEMS Vibrational Energy Harvester for Wireless Sensor Power Dr. Mark Boysel, CTO Mary Boysel , President and CEO MCB Clean Room Solutions

Transcript of MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick...

Page 1: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

13 October 2011 1

MEMS Vibrational Energy Harvester for Wireless Sensor Power

Dr. Mark Boysel, CTOMary Boysel , President and CEO

MCB Clean Room Solutions

Page 2: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

Micro-Vibrational Energy Harvester (µVEH)� MCB is developing a MEMS (Micro-Electro-Mechanical Systems) piezoelectric µVEH to power wireless sensors.

• Converts environmental vibrations into electricity• Replaces or recharges batteries• Goal is 3 V, 0.1-1mW in a single piezo element • Package target: < 1cm2 footprint, < 1cm3 volume

� Targeting Building Controls and HVAC• Rich source of 120 Hz vibrations• 3% of Wireless Sensor Market• Largest market for low power energy harvesters

13 October 2011 2

Page 3: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

The Opportunity – Wireless Sensor Networks

13 October 2011 3

� Wireless Sensor Networks (WSN) market estimated to reach $7.8B by 2015

• Sensors for infrastructure, industrial processes, security

• Energy and cost savings by monitoring processes, energy use

� Batteries need to be changed

• Embedded sensors (e.g. HVAC) are difficult to access

• Cost of changing batteries ~ $2/year/battery ($2 B annually)

• Up to 90% of potential wireless apps not attempted because of battery changes

� Wireless sensors need to be self-powered – Energy scavengers

� Market for low power energy harvesters for buildings estimated at $75M in 2009 growing at 74% AAGR to $1.2B in 2014

Page 4: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

Why Vibrational Energy Harvesters?

13 October 2011 4

� Several other energy harvesting technologies available

• Not ideal for Building Controls and HVAC

• Solar - Light may not be available in embedded sensor locations in buildings and HVAC

• Thermal - Requires a temperature gradient that may not be available in an embedded environment

• RF – Requires an external power transmission source

� Vibrational harvesters can use vibrations of electrical equipment and motors in buildings

• Electromagnetic – Coil and magnet tend to be large, expensive

• Piezoelectric – Materials have historically been difficult to work with

Page 5: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

� For widespread use Wireless Sensors (WS) will require small (< 1cm3, 1cm2 footprint), inexpensive (<$10) power sources.

� Macro- Energy Harvesters provide plenty of power but are large and expensive.

� MEMS (Micro-Electro-Mechanical Systems) use volume semiconductor wafer manufacturing processes - Many parts per wafer

• Small, inexpensive – Think $1 accelerometers

Why MEMS?

13 October 2011 5

Transducer only

System

Electromagnetic EH Piezoelectric EH

Wireless Sensor Thermal EH

Page 6: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

The Problem With MEMS

13 October 2011 6

� Because they are small MEMS produce little power and operate at high frequencies.

� Stress in piezoelectric produces voltage between faces

• V = d31 σav / ϵp tp,

• Stress, σ = Y∆y/R, ∆y=distance to neutral axis

• For MEMS thin film processes ∆y is small

• Thin films are on the order of 1-2 µm thick.

� Use multiple cantilevers or multiple chips

� Stress gradient curling

Page 7: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

MCB’s Solution

13 October 2011 7

� MEMS Thick Beam Process (Pat. App. US20110210554)

• Proprietary process to create a cantilever that is thicker than is typical of conventional MEMS surface micromachining processes

• Raises piezoelectric film ~10X further away from neutral axis

• 100 x increase in power

• Eliminates stress curling

Page 8: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

Scale Model Proof of Concept

13 October 2011 8

� Manually constructed spring and mass cantilevers at 25 X scale

• Identical PZT (Lead Zirconate Titanate) sheets (2” x 0.5” x 0.005”)• Silver epoxied to brass shim cantilevers

• Thin monomorph - 0.01” thick• Thick bimorph - 0.05” thick.

� Lead proof masses added to equalize resonant frequencies (75 Hz)� Frequency spectra taken with fixed 220 kHz load instead of optimized load.

� Output voltage ratio of thick bimorph to monomorph was 8V/0.2 V, or a factor of 40.

• Corresponds to a power ratio of 1600 (non-optimized)

Page 9: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

MEMS Design and Power Modeling

13 October 2011 9

� Roundy and Wright developed an expression for the power output of a macro-VEH bimorph.

� Optimize load resistance for ω.

� Calculate P, V, Stress

Piezo thickness = 0.5 um

Cantilever thickness (m) Cantilever thickness (m)

Page 10: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

MEMS Design and Fabrication

13 October 2011 10

� Design splits for model verification

• Frequency arrays

• Designs around process splits

• Adjust proof mass to match spring

• Designs for fixed 120 Hz frequency

� Fabrication at Cornell Nanoscale Science and Technology Facility (CNF)

• Releasing first prototypes

• Packaging and Testing this month

Page 11: MEMS Vibrational Energy Harvester for Wireless Sensor Power · • Thin monomorph - 0.01” thick • Thick bimorph - 0.05” thick. Lead proof masses added to equalize resonant frequencies

13 October 2011 11

AcknowledgementsWe are grateful for support from the National Science Foundation (NSF) and the New York State Energy Research and Development Authority

(NYSERDA)

We also wish to acknowledge assistance from Venture Creations for business and proposal support and to NYSTAR and the Cornell Center

for Materials Research (CCMR) through the JumpStart Program.