MegaPower 48 Installation Manual - American...

MegaPower 48Installation Manual

MegaPower 48

Matrix Switcher / Controller System

Installation Manual

Copyright 2000

All Rights Reserved

No part of this manual may be reproduced in any formwithout written permission from Sensormatic Electronics Corporation

8000-1803-51, Revision B

12/2000

WARNINGDo not install this product in hazardous areas where highly combustible or explosiveproducts are stored or used.

FCC COMPLIANCEThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercialenvironment. The equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance withthe instruction manual, may cause interference to radio communications.

Operation of this equipment in a residential area may cause interference in which case the user will be required to correct theinterference at his own expense.

EQUIPMENT MODIFICATION CAUTIONEquipment changes or modifications not expressly approved by Sensormatic Electronics Corporation, the party responsible for FCCcompliance, could void the user’s authority to operate the equipment, and could create a hazardous condition.

WARRANTY DISCLAIMERSensormatic Electronics Corporation makes no representation or warranty with respect to the contents hereof and specifically disclaimsany implied warranties of merchantability or fitness for any particular purpose. Further, Sensormatic Electronics Corporation reserves theright to revise this publication and make changes from time to time in the content hereof without obligation of Sensormatic ElectronicsCorporation to notify any person of such revision or changes.

Copyright 2000

All Rights Reserved

No part of this manual may be reproduced in any form without written permission from Sensormatic® Electronics Corporation.

MegaPower™, Sensormatic™ and the Sensormatic Logo are registered trademarks of Sensormatic Electronics Corporation.

Product names mentioned herein may be trademarks or registered trademarks of other companies

PN 8000-1803-51, Revision B

Table of Contents iii

Table of Contents

Introduction ..................................................................................................................................................................1MegaPower 48 Assembly ....................................................................................................................................1

MegaPower 48 Installation Kit......................................................................................................................1Recommended Tools (not included) ............................................................................................................1

Mechanical Installation............................................................................................................................................1Start Up Diagnostics..............................................................................................................................................2Drawing 1: Wall Bracket Installation .............................................................................................................3Drawing 2: Patch Panel & Wall Bracket ........................................................................................................4Drawing 3: Cable Management Bracket .......................................................................................................5 Drawing 4: Center-Tapped Transformer......................................................................................................6Drawing 5: Main Electronics Unit .....................................................................................................................7

Patch Panel Overview ..............................................................................................................................................8Video Inputs Section (Camera Icon) ................................................................................................................8Video Outputs Section (Monitor Icon) .............................................................................................................8Relay Section (Switch Icon)..................................................................................................................................8Alarms Section (Bell Icon) ...................................................................................................................................8Diagnostics Section (Wave Form Icon)............................................................................................................8Communications Section (Dome Icon).............................................................................................................8Power Section (Sine Wave Icon)........................................................................................................................8RS232 Section (PC Icon)........................................................................................................................................8Modem Section (Telephone Icon) .....................................................................................................................8Drawing 6: MegaPower 48 Patch Panel ........................................................................................................9System Programming .........................................................................................................................................10System Integration...............................................................................................................................................10AC Power Requirements ....................................................................................................................................10

System Connections .................................................................................................................................................10Video Connections ...............................................................................................................................................10Drawing 7: Video Inputs & Outputs ..............................................................................................................11Cable Networks ....................................................................................................................................................12

System Communications ........................................................................................................................................12Manchester Communications ...........................................................................................................................12

Daisy Chain Connections ...............................................................................................................................12AD2083-02B Code Translator ......................................................................................................................12

Drawing 8: AD1641 Receiver ...........................................................................................................................13Drawing 9: AD2083-02B Code Translator...................................................................................................14Star Connections / AD1691 Code Distributor .............................................................................................15

AD2031/2032/2033 Accessories .................................................................................................................15SensorNet Communications .............................................................................................................................15

SensorNet Daisy Chain Configurations ....................................................................................................15Star Connections / 6-Position J-Boxes ......................................................................................................15Additional SensorNet Documentation ......................................................................................................15

SEC RS-422 Communications............................................................................................................................15RS-422 Daisy Chain Connections ................................................................................................................15Star Connections / 10-Position J-Boxes....................................................................................................15Additional RS-422 Documentation.............................................................................................................15

Drawing 10: AD1691 Code Distributor.........................................................................................................16Drawing 11: AD2031 Switcher Follower ......................................................................................................17Drawing 12: SensorNet 6 Position J-Box.....................................................................................................18Drawing 13: RS-422 10 Position J-Box.........................................................................................................19RS-232 Communications ....................................................................................................................................20

RS-232 Keyboard Connections ....................................................................................................................20

iv Table of Contents

Port Expander....................................................................................................................................................20RS-232 PC Connection.....................................................................................................................................20RS-232 External Modem Connection .........................................................................................................20

Drawing 14: AD2088 Keyboard......................................................................................................................21Drawing 15: ADTTE Keyboard .........................................................................................................................22Drawing 16: AD2081 Port Expander .............................................................................................................23Drawing 17: PC & Modem Connections........................................................................................................24

RS-232 Alarm Interface Unit Connection.................................................................................................25Additional AD2096A Documentation ........................................................................................................25RS-232 Peripheral Interface Port Connection ........................................................................................25Additional PIP Documentation ....................................................................................................................25

Direct Alarm and Relay Connections.............................................................................................................25Relay Outputs ....................................................................................................................................................25Patch Panel Alarms .........................................................................................................................................25System Alarm Handling .................................................................................................................................25

Technical Support.....................................................................................................................................................25Drawing 18: AD2096A........................................................................................................................................26Drawing 19: Video Recorder Control ............................................................................................................27Drawing 20: Alarm & Relay Sections ............................................................................................................28

Troubleshooting Guide ..........................................................................................................................................29Declaration of Conformity .....................................................................................................................................31MegaPower 48 Product Specifications..............................................................................................................32Index .............................................................................................................................................................................36

Mechanical Installation 1

IntroductionMegaPower 48 is a video routing system with a broadrange of functionality.Viewing and control of up to 48 cameras or domes canbe accomplished through SEC-422, AD Manchester,and SensorNet communication protocols.The system provides 16 video outputs. Outputs 1-8provide video and a text overlay with status and alarminformation. Outputs 9-16 provide video without textfor uses such as public monitors..The system panel provides two form C relay outputsand 16 normally open alarm contact terminals. Adiagnostics section provides power and unit operatingstatus, and a push-button system reset switch.Power terminals connect to a 24 VAC transformer foreither 120 VAC or 230 VAC inputs.Eight RS-232 ports enable connection to systemkeyboards, printers, PCs, auxiliaries, alarm interfaceunits, external modems for paging functions, and aninterface for video recorders. When used with theAD2088 keyboard, the system has macro programmingand synchronization capability, and can control up to2048 video recorders.

MegaPower 48 AssemblyThe MegaPower 48 assembly is designed for verticalsuspension hollow-wall or solid wall mounting. Anoptional rack-mount kit is also available. TheMegaPower 48 assembly and assorted accessories areshipped to the user in two boxes.Box 1 contains the hardware and accessories necessaryfor the first stage of MegaPower 48 installation. Box 2contains the hardware necessary to complete theinstallation, and also contains the system manuals andsoftware disks.Keep Box 2 in a clean, secure location while the firststage of installation is in progress. After the first stage iscomplete and debris is removed, bring Box 2 to the areato complete the installation in a clean workspace.MegaPower 48 Installation KitBox 1: PN 0100-0490-01Description Qty Part NumberMounting Bracket 1 0500-5606-01Patch Panel Assy 1 0300-1642-01Cable Mgt Bracket 1 0500-5656-01Cable Mgt Tie Kit: 1 0351-1345-01 Tie Wrap Clips 12Wall Mount Hardware Kit: 1 0351-1342-01 Toggle Bolts 6 Bolt Anchors 6Installation Template 1 8000-1797-01Accessory Kit: 1 0351-1341-01 Cables with Junction Boxes 3 S3 Cable w/ DB9F Adaptor 1Patch Panel Hardware Kit 1 0351-1343-01 M4x6 Flathead Screws 2 5801-2042-120Mounting Instructions 1 8000-1800-01

Box 2: PN 0100-0491-51 (NTSC) or -52 (PAL)Description Qty Part NumberMain Electronics Unit, NTSC 1 0300-1843-01Main Electronics Unit, PAL 1 0300-1843-02Transformer (USA) 1 0300-1889-01Transformer (International) 1 0300-1889-03AC Line Cord (USA) 1 0351-0547-01AC Line Cord (European Union) 1 0351-0547-02AC Line Cord (UK) 1 0351-0547-03AC Line Cord (Japan) 1 0351-0547-04AC Line Cord (Australia) 1 0351-0547-07Document Kit (English) 1 0351-1338-51

Installation Manual 1 8000-1803-51Programming Manual 1 8000-1804-51

Recommended Tools (not included)● Medium Phillips Head Screwdriver

● Small Slotted Screwdriver

● Level

● Tie Wraps

● BNC Removal Device

● Marking Implement (Pen or Pencil)

● Power Drill with drill bit: 11/16” (17.5mm), hollow wall, 1/2” (12.7mm), solid wall

Mechanical Installation1. Remove the components from Box 1 and arrange

them on a surface near the mounting location.2. Remove and discard the red shipping knobs

attached to the patch panel assembly. The knobsare used only for factory packaging and must beremoved prior to installation.

3. Using a level, position the installation templatewhere the assembly is to be mounted. Provide atleast 14” (36cm) clearance from the bottom edge ofthe mounting bracket (which is the first componentof the assembly to be installed) to accommodate theentire assembly. Temporarily tape the template tothe wall.

4. Using the template, carefully mark the drill pointson the mounting surface. Make sure that the drillpoints are positioned where there are noobstructions behind the wall surface. Remove thetemplate and drill the holes for the suppliedhardware.

5. Depending on the wall type, secure the mountingbracket using the four bolts or screws provided.Secure the mounting bracket using the four bolts orscrews provided. (see Drawing 1, Page 3).

6. Position the patch panel such that the screw holesin the mounting bracket’s two lower mountinghooks are aligned exactly with the twocorresponding holes on the patch panel assembly.Install the two M4x6 flathead screws using aPhillips head screwdriver. (see Drawing 2, Page 4).

7. Insert cable tie-wrap clips into the desired holes onthe cable management bracket. Secure the cablemanagement bracket to a surface near the patch

2 Mechanical Installation

panel assembly. Attach system cables to theappropriate patch panel connectors. Arrange cablesin manageable groupings and secure the groups tothe cable management bracket by means of tiewraps looped through the tie wrap clip slots. (seeDrawing 3, Page 5).

Completion of the assembly requires connection of thetransformer with AC line cord, and attachment of theMain Electronics Unit.8. Remove the hardware from Box 2. Connect the

transformer to the patch panel as shown in Drawing4, Page 6. Depending on the system version, thetransformer cable will connect to either A) the maleconnector of the patch panel power cable (seedetail A in Drawing 4) or B) the male powerconnector on the patch panel (see detail B inDrawing 4). Connect the line cord to thetransformer (if necessary) and the AC outlet. Note:to exercise sound practice, it is recommended thatthe MegaPower 48 system and critical systemcomponents be connected to an uninterruptiblepower supply to insure continuous operation duringlimited power outages. The system so equipped willmeet or exceed the requirements of EN 50130-4.

9. Fit the Main Electronics Unit on the patch panelassembly’s three guide hooks. (see Drawing 5, Page7).

10. Push upwards, with even pressure on the two lowercorners of the Main Electronics Unit, until the Unitmates securely with the patch panel receptacles,and a distinct click is heard when the locking pinsengage. Note: the main electronics unit isdisengaged from the patch panel assembly bypressing the two side triggers and pulling to theside and down simultaneously, alternately movingfrom left to right, in three or four short, gentle,movements.

11. When the Main Electronics Unit is connected, thesystem will start.

Start Up Diagnostics

When the Main Electronics Unit is connected withpower applied, normal operation is indicated by thefollowing:

● The ventilation fan is audible.

● The AC power LED (sine wave icon) in the upperright-hand section of the patch panel illuminates.

● The UOP LED (heartbeat icon) blinks.

If normal operation is indicated, call a monitor with asystem keyboard, and then call a camera to the calledmonitor. Note: the four yellow LEDs beneath the ACpower LED are not operative with this version of thesystem.

If the event of absent or abnormal diagnostic signals,power the system down and re-check systemconnections. If necessary, consult the troubleshootingsection of this manual.

If you need assistance, contact your Sensormaticrepresentative.

Patch PanelDiagnostics Section


Drawing 1: Wall Bracket Installation

��yy

��yy��yy

��yy�y�y��yy

Drawing 1: MegaPower 48 Mechanical InstallationWall Bracket Assembly

WALL BRACKET

HOLLOW WALL SURFACE

BUTTERFLY TOGGLE-BOLTINSTALLATION

SOLID WALL MOUNT OPTIONS


Drawing 2: Patch Panel & Wall Bracket

Drawing 2: MegaPower 48 Mechanical InstallationPatch Panel and Wall Bracket Assembly

PATCH PANEL

WALL BRACKET ASSEMBLY

PATCH PANEL CUT-OUT OVER WALLBRACKET MOUNTING HOOKSECURED BY M4x6 FLAT-HEAD SCREW


Drawing 3: Cable Management Bracket

Drawing 3: MegaPower 48 Mechanical InstallationCable Management Bracket – Tie Wraps & Clips

6" MINIMUM

Cable Mounting BracketOptions

CABLE MANAGEMENT BRACKET

PATCH PANEL ASSEMBLY

SECURING BRACKETWITH TOGGLE BOLT

BRACKET CLIPAND TIE -WRAP

BRACKET MOUNTING OPTIONS

6 “MINIMUM


Drawing 4: Center-Tapped Transformer

Drawing 4: AC Power SectionPatch Panel to Center-Tapped Transformer

TRANSFORMER CABLE TO PATCHPANEL CABLE CONNECTIONA)

24 VAC TERMINALS FOR SYSTEM VERSION A:WITH FACTORY-INSTALLED PATCH PANEL CABLE

24 VAC TERMINALS FOR SYSTEM VERSION B: WITHPOWER CONNECTOR ATTACHED TO PATCH PANELB)


Drawing 5: Main Electronics Unit

Drawing 5: MegaPower Mechanical InstallationAttaching the Main Electronics Unit (MEU)

LockingPin

STEP 1 -ALIGN MEU CUT-OUTS WITHPATCH PANEL GUIDE HOOKS

STEP 2 -PUSH UPWARDS UNTILMEU CLICKS INTO POSITION

DETAIL OF RELEASE TRIGGER(S)AND LOCKING PIN(S)

8 Patch Panel Overview

Patch Panel OverviewThe MegaPower 48 patch panel contains 12 sections forvideo switching, communications, power, alarmhandling, and auxiliary control. The patch panel alsocontains a diagnostics section providing system statussignals. See Drawing 6, Page 9 for an illustration of thepatch panel.

A brief description of each patch panel section follows.

Video Inputs Section (Camera Icon)

The video inputs section provides 48 BNC connectorsfor connection of RG-59U video cables to systemcameras and/or domes. Cable distance should notexceed 1000 feet (330 meters).

Video Outputs Section (Monitor Icon)

The video outputs section provides 16 BNC connectorsfor connection to system video monitors and/orrecorders. Monitors 1-8 display video and a text overlaythat provides information about the displayed video.Monitors 9-16 display video with no text overlay.

Relay Section (Switch Icon)

The relay section provides two three-position screwterminal blocks for connection of Form C relay outputs.Terminal positions are normally open, normally closed,and common.

Alarms Section (Bell Icon)

The alarms section provides two 16-position screwterminal blocks for 16 normally open alarm contactclosure wires and 16 alarm ground wires.

Diagnostics Section (Wave Form Icon)

The diagnostics section provides indicators for thepresence of AC power (sine wave icon), normal systemoperation (heartbeat icon), and a four LEDs to displaystatus signals. This section also provides a push buttonsystem reset switch.

Communications Section (Dome Icon)

SEC-422: Provides three eight-position screw terminalblocks for connection of up to six RS422 devices suchas AD domes and J-Boxes.

AD Manchester: Provides one three-position terminalblock for the connection of a single Manchester devicesuch as the AD1691 Code Distributor or the AD1641MReceiver/Driver.

SensorNet: Provides two six-position screw terminalblocks for the connection of up to six SensorNet devicessuch as AD domes or J-Boxes. An adjacent six positionDIP switch allows for termination of each SensorNetport.

Power Section (Sine Wave Icon)

Depending on the system version, the power sectionprovides either A) a factory-installed power cable witha three circuit male connector, or B) a three circuitmale connector that is factory installed on the patchpanel.

RS232 Section (PC Icon)

The RS232 section provides eight RJ-45 jacks forconnection of RS232 devices such as PCs, AD2088 andADTTE keyboards, Port Expanders, AD2096A AlarmInterface Units, and standard external modems.

Modem Section (Telephone Icon)

The modem section provides a DB9 connector for theconnection of a standard external modem for messagepaging functions. Note: either the DB9 connector or RJ-45 jack number 8 of the RS232 section can be used asan alternative port for an external device (eitherconnector is recognized as Port 8 by the MegaPower48 system, but both connectors cannot be used at thesame time).

Patch Panel Overview 9

Drawing 6: MegaPower 48 Patch Panel

Drawing 6: MegaPower 48 Patch Panel

CAMERA/DOME CONTROL &COMMUNICATIONS(RS-422, MANCHESTER &SENSORNET)

VIDEO INPUTS

VIDEO OUTPUTS RELAYS ALARMS DIAGNOSTICS

RS-232

AC POWER

10 System Connections

System ProgrammingMegaPower 48 can be programmed with a systemkeyboard and monitor using software embedded in thesystem’s Main Electronics Unit, or with a PC interfaceand S3 system setup software.Instructions for programming are provided in theMegaPower 48 System Programming and OperatingManual, part number 8000-1804-51.

System IntegrationThe MegaPower 48 system can also be integrated withother Sensormatic security systems and devices. Amongthe products available for integration are:● C-Cure 800 Security Management System● Intellex Digital Video Management System● Integra Digital Time Lapse Recorder

Additional Integration Documentation● Intellex Digital Video Management System

Installation Instructions – part number 8000-2205-00● Integra Time Lapse Recorder Installation/Operation

Manual – part number 8000-2195-01

AC Power RequirementsPower is supplied to the MegaPower 48 patch panel viaa center-tapped transformer (see Drawing 4, Page 6).● Transformer (USA): 0300-1889-01

Input voltage: 120 V @ 630 mA, 50-60 HzAC leads are black and white. Ground is red.

● Transformer (International): 0300-1889-03Input voltage: 230 V @ 315 mA, 50-60 HzAC leads are brown and blue. Ground is green/yellow.

● Cable required: 3 conductor, unshielded, 18 AWG.

To exercise sound practice, it is recommendedthat the MegaPower 48 system and critical systemcomponents be connected to an uninterruptiblepower supply to insure continuous operationduring limited power outages. The system, soequipped, will meet or exceed the requirements ofEN 50130-4

System ConnectionsConnections are made to and from various systemdevices and the MegaPower 48 patch panel. In somecases, simple, direct connections can be made fromdevice to panel. In other cases, system accessories areutilized to implement appropriate system operation.MegaPower 48 system accessories include thefollowing:● AD2031 Switcher Follower● AD2032 Alarm Responder● AD2033 Auxiliary Follower● AD1641 Series Receivers● AD1981 Port Expander● AD2083-02B Code Translator● AD1691 Code Distributor● AD2096A Alarm Interface Unit● J-Boxes● AD100 Series Recorder Control Interfaces

Video Connections● Video cable required for both inputs and outputs: RG-

59U (Belden 8241 or equivalent).● Maximum cable length: 1000 feet (305m)● Video standards supported: NTSC, PAL● Output termination requirements: 75 ohms at the last

unit in the run.● Video cables should be labeled with an identifier

associated with the appropriate BNC connector on thepatch panel.

See Drawing 7, Page 11 for an illustration of typicalvideo inputs and video outputs.

System Connections 11

Drawing 7: Video Inputs & Outputs

Drawing 7: Patch Panel to Video Inputs & Video Outputs

VIDEO INPUTS SECTION48 BNC CONNECTORS

RG-59U VIDEO CABLE

DOME

CAMERA

VIDEO OUTPUTS SECTION16 BNC CONNECTORS

RG-59U VIDEO CABLE

SYSTEM MONITOR -TERMINATE LAST UNIT IN RUNIN 75 OHMS


Cable Networks

Cable networks provide the means through which theMegaPower 48 Main Electronics Unit communicateswith receiver/driver units and domes. Three types ofnetworks can be used with the Manchester, SensorNet,or SEC-422 protocols.

● Daisy Chain – in a daisy chain configuration, aseparate cable connects each device to the next devicein the chain.

● Backbone – in a backbone configuration, a single,continuous cable connects all domes in the networklink.

● Star – in a star configuration, up to four branchesconnect to a central hub location (typically a J-Box orother data distribution unit). Domes can attach withseparate cables (daisy chain style),

or, with a single continuous cable (backbone style).

Note: both ends of a cable run must be terminated.Black device blocks illustrated above indicateterminated devices.

System CommunicationsThe MegaPower 48 CPU communicates with systemdevices through four communications protocols:● RS-232 (PC icon)● SEC RS-422 (dome icon)● SensorNet (dome icon)● Manchester (dome icon)

RS-422, SensorNet, and Manchester protocols are usedin the control of domes and pan/tilt cameras.RS-232 enables communications with systemkeyboards, PCs, auxiliaries, alarm interface units,external modems, port expanders, and video recorderinterface units.

Manchester CommunicationsThere is a single Manchester connector on theMegaPower 48 patch panel. The connector consists ofthree terminals labeled Black (“B”), White (“W”), andShield (“S”). Manchester is a one-way communicationsprotocol.

Cable required: 18 AWG, 2-wire, shielded twisted pair.polarized, Belden 8760 or equivalentFor Plenum applications, Belden 88760or equivalent

Maximum distance: 5000 feet (1.5km)Data rate: 31 kb/sec

Daisy Chain ConnectionsWhen wired directly from the patch panel connector toa receiver/driver or integrated dome in a Manchesternetwork, a maximum of three video sources can beconnected via a daisy chain connection. The last unit inthe daisy chain must be terminated at 120 ohms. SeeDrawing 8, Page 13 for a typical direct connection to anAD1641 Receiver.

AD2083-02B Code TranslatorThe MegaPower 48 CPU can output Manchester codeto control domes utilizing the SEC RS-422communications protocol by using the AD2083-02BCode Translator as an interface between the patch paneland the domes.A single AD2083-02B provides 16 terminals using the4-wire RS-422 protocol. DIP switches on the rear panelof the AD2083-02B enable addressing for specificgroups of cameras. All 48 video inputs for theMegaPower 48 patch panel can be connected through asingle AD2083-02B by wiring each terminal to a three-dome daisy chain group.See Drawing 9, Page 14 for a typical connection fromthe MegaPower 48 Manchester terminals to anAD2083-02B to an integrated dome.


Drawing 8: AD1641 Receiver

Drawing 8: Manchester CommunicationsPatch Panel to AD1641 Receiver to AD1240 Pan/Tilt

PATCH PANELMANCHESTER CODE CONNECTOR

SHIELDED, 18 AWG DATA CABLEMAXIMUM LENGTH = 5000 FEET (1.5 km)

AD1641 RECEIVER

AD1240 PAN/TILT AND CAMERA


Drawing 9: AD2083-02B Code Translator

Drawing 9: Manchester CommunicationsPatch Panel to AD2083-02B Code Translator to Integrated Dome


AD2083-02BMANCHESTER DATAINPUT CONNECTOR

AD2083-02B DATAOUTPUT CONNECTOR

AD2083-02B CODE TRANSLATOR


Star Connections / AD1691 Code DistributorWhen the patch panel’s Manchester black, white, andshield terminals are wired to the input terminals of anAD1691 Code Distributor, up to 64 Manchester outputscan be transmitted to receiver/drivers and integrateddomes. See Drawing 10, Page 16 for a typicalconnection utilizing the AD1691.

AD2031/2032/2033 AccessoriesThe MegaPower 48 CPU can output Manchester codeto control external circuit switching synchronized withthe switching of video inputs to video outputs (via theAD2031 Switcher Follower). It can also synchronizeexternal circuits with the switching of auxiliary contactsassociated with individual video inputs (via the AD2033Auxiliary Follower). Additionally, it can provide relaycontact closures for corresponding video outputs thatare displaying alarm conditions (via the AD2032 AlarmResponder).See Drawing 11, Page 17 for a typical connection of thepatch panel to an AD2031 synchronized with anexternal audio circuit.

SensorNet CommunicationsSensorNet is a two wire, two-way communicationsprotocol. There are 12 screw terminals on theMegaPower 48 patch panel providing six channels forSensorNet communications. Directly below theSensorNet screw terminals is a DIP switch that is usedto terminate each of the six channels.

Cable required: 22 AWG, single twisted pair,unshielded, non-polarized. Belden 8442or equivalent.

Maximum distance: 3300 feet (1km)Data rate: 230 kb/sec

SensorNet Daisy Chain ConfigurationsEach SensorNet patch panel terminal pair can be wireddirectly to eight-dome daisy chain groups toaccommodate all 48 video inputs available toMegaPower 48.

Star Connections / 6-Position J-BoxesEach SensorNet patch panel terminal can be wired to a6-position J-box. The J-Box serves as a hub for starconnections for up to 6 domes. Each J-Box-to-domeconnection can also serve as the starting point for adaisy chain group. See Drawing 12, Page 18 for atypical connection of the patch panel to a 6-position J-box.

Additional SensorNet Documentation● SensorNet 1-Position J-Box Installation Guide –

part number 8000-0971-01.● SensorNet 6-Position J-Box Installation Guide –

part number 8000-0975-01.● SensorNet Network Design Guidelines -

part number 8000-0970-01

SEC RS-422 CommunicationsRS-422 is a four wire, two way communicationsprotocol. There are 24 screw terminals on theMegaPower 48 patch panel providing six four–terminalchannels for RS-422 communications.

Cable required: 22 AWG, four conductor, doubletwisted pair (polarized).

Maximum distance: 3000 feet (915m)Data rate: 4.8 kb/sec

RS-422 Daisy Chain ConnectionsEach RS-422 patch panel four terminal group can bewired directly to eight-dome daisy chain groups toaccommodate all 48 video inputs available toMegaPower 48.

Star Connections / 10-Position J-BoxesEach RS-422 patch panel terminal group can be wiredto a 10-position J-box. The J-Box serves as a hub forstar connections for up to 10 domes. All 48 video inputscan be accommodated using six 10-position J-boxes,with each J-Box connected to six domes. See Drawing13, Page 19 for a typical connection of the patch panelto a 10-position J-box.

Additional RS-422 Documentation● RS-422 1-Position J-Box Installation Guide –

part number 8000-0588-01.● RS-422 10-Position J-Box Installation Guide –

part number 8000-0320-01.● Communications Protocols and Cable Networks -

part number 8000-2573-19


Drawing 10: AD1691 Code Distributor

Drawing 10: Manchester CommunicationsPatch Panel to AD1691 Code Distributor to Integrated Dome


3-PRONG DATA OUTPUT CONNECTOR

AD1691 CODE DISTRIBUTOR

AD1691 DATA INPUT CONNECTOR


Drawing 11: AD2031 Switcher Follower

Drawing 11: Manchester CommunicationsPatch Panel to AD2031 Switcher Follower to Audio Circuit


RELAY GROUPINPUTS/OUTPUTS

AD2031 DOUBLE POLERELAY INPUT

AD2031 MANCHESTERDATA INPUT

SECURITY STATIONSPEAKER & MICROPHONE

SYSTEMSPEAKER / MICROPHONE UNIT


Drawing 12: SensorNet 6 Position J-Box

Drawing 12: SensorNet CommunicationsPatch Panel to 6-Position J-Box to Integrated Dome

1

5

PATCH PANEL SENSORNET CONNECTOR

6 POSITION J-BOX

DATA CABLE TO PINS 1 & 2OF J-BOX 4-POSITIONCOMPRESSION CONNECTOR

COMPOSITE CABLE TO J-BOX 5-POSITIONCOMPRESSION CONNECTOR


Drawing 13: RS-422 10 Position J-Box

Drawing 13: RS-422 CommunicationsPatch Panel to 10-Position J-Box to Integrated Dome

PATCH PANEL RS-422 CONNECTOR

10 POSITION J-BOX

COMPOSITE CABLE TO J-BOXJONES CONNECTOR

DATA CABLE TO SPRING-LOADEDTERMINAL BLOCK


RS-232 Communications

The RS-232 section (PC icon) of the MegaPower 48patch panel consists of eight RJ-45 receptacles and oneDB-9 receptacle.Cable required: modular eight conductor cable – cable

distance (7 or 14 feet) and plugdependent on application.

Accessories: wall-mount eight pin terminal box. Boxcan be single or dual mount dependent onapplication.

Additional Cable: 18 AWG, three-wire, shielded cable.Maximum cable distance = 1000 feet(305m).

RS-232 Keyboard ConnectionsMegaPower 48 release 1.0 can utilize any of threekeyboards: AD2079, AD2088, and ADTTE TouchTracker.AD2088 provides the user with the largest features set,including video recorder control and macroprogramming and synchronization.Unlike the other two models, the AD2088 uses theENTER key (rather than the ACK key) for data entry inthe Menu programming mode of operation.

The AD2079 and AD2088 are connected to theMegaPower 48 patch panel by a seven foot modularcable with RJ-45 plugs, and a dual 8-pin wall mountterminal box. Power to the keyboard is provided by atransformer connected to the terminal box. Forconnections greater than seven feet, an additional single8-pin terminal box is used with 3-wire, 18 AWGshielded cable. Maximum cable length = 1000 feet(305m). See Drawing 14, Page 21 for a typicalconnection using the AD2088 keyboard.

The ADTTE Touch Tracker keyboard connects to anEIM module via an 8 conductor, 14 foot modular cablewith RJ-45 plugs. MegaPower 48 RS-232 ports connectto the EIM module via an 8 conductor cable with an RJ-45 plug at one end, and a DB9M connector at the otherend. Power is provided to the keyboard via atransformer connected to the EIM module via a 5 pinscrew terminal connector. For connections greater than14 feet, two single 8-pin wall mount terminal boxes areused with the EIM module and 3-wire, 18 AWGshielded cable. Maximum cable length = 1000 feet(305m). See Drawing 15, Page 22 for a typicalconnection using the ADTTE keyboard.

Port ExpanderAn RS-232 port with keyboard device type assignmentcan be connected to up to four keyboards through theuse of the AD2081 Port Expander. The RS-232 port isconnected to an RJ-45 CPU input receptacle on the PortExpander via a seven foot modular cable with RJ-45plugs. The keyboards are then wired from any of thefour Port Expander output ports using theconfigurations discussed in the section on RS-232Keyboard Connections. See Drawing 16, Page 23 for atypical connection using the AD2081 Port Expander.

RS-232 PC ConnectionAn IBM-compatible PC can be connected to anMegaPower 48 RS-232 port for the purpose ofdownloading S3 system setup software parameters tothe system, or uploading system parameters to the PC.A seven foot (2.2 m) modular cable with RJ-45 plugs,and converter with an RJ-45 receptacle and a DB9Fconnector are connected to the DB9M on one of thePC’s COM ports. See Drawing 17, Page 24 for a typicalMegaPower 48 RS-232 port to PC connection.

RS-232 External Modem ConnectionPort 8 of the MegaPower 48 patch panel RS-232 sectionhas two different connectors. A DB9M connector isprovided for connection to an external AT command setmodem. Any other device assigned to port 8 isconnected to the RJ-45 receptacle. Note: only onedevice can be connected to port 8. Both receptaclescannot be connected simultaneously. Connection to amodem is made using a modular seven foot cable withDB9F and DB25M connectors at the cable ends. Themodem can be connected to analog telephone linesonly. See Drawing 17, Page 24 for a typical MegaPower48 RS-232 port to modem connection.


Drawing 14: AD2088 Keyboard

Drawing 14: RS-232 CommunicationsPatch Panel to AD2088 Keyboard

ToTransformer

DUAL 8-PIN WALL MOUNTTERMINAL BLOCK

RS-232 SECTION

AD2088 KEYBOARDCONNECTIONS OF 7 FEET OR LESS

3 WIRE 18 AWG SHIELDED CABLE

SINGLE 8-PIN WALL MOUNTTERMINAL BLOCK

AD2088 KEYBOARDCONNECTIONS GREATERTHAN 7 FEET

TRANSFORMER9 VAC OUTPUT


Drawing 15: ADTTE Keyboard

Drawing 15: RS-232 CommunicationsPatch Panel to ADTTE Keyboard

#1#2

#1

#2

52 3

2 3 5

RS-232 SECTION

EIM MODULE

ADTTE KEYBOARDCONNECTIONS OF 14 FEET OR LESS

WIRING FOR TWO SINGLE 8-PIN WALL MOUNTTERMINAL BLOCKS – USING 3-WIRE 18 AWGSHIELDED CABLE

PIN COLOR NAME2 RED Tx3 GREEN Rx5 ORANGE GROUND

RJ-45 TO DB-9 CONNECTIONS

PIN NAME2 24 VAC A3 GROUND4 24 VAC B

TRANSFORMER TO SCREWTERMINAL CONNECTIONS

ADTTE KEYBOARDCONNECTIONS GREATER THAN 14 FEET

TRANSFORMER24 VAC OUTPUT


Drawing 16: AD2081 Port Expander

435

43 5

RS-232KEYBOARD PORT

AD1981 PORT EXPANDERCONNECTS UP TO FOURAD SYSTEM KEYBOARDS

TERMINAL BOX PIN DB9F PIN4 35 47 5

TERMINAL BOX TO DB9FCONNECTIONS

DB9 CONNECTOR TOAD1981 CPU PORT

Drawing 16: RS-232 CommunicationsPatch Panel to AD1981 Port Expander to System Keyboards

AD2088 KEYBOARDS CONNECTEDTO AD1981 KEYBOARD PORTS

8 PIN TERMINAL BOX LINKINGMODULAR CABLE FROM PATCH PANELTO SHIELDED 3-WIRE CABLE TOAD1981 PORT EXPANDER


Drawing 17: PC & Modem Connections

Drawing 17: RS-232 CommunicationsConnections to PC and External Modem

PATCH PANELRJ-45 RECEPTACLE

RJ-45 PLUG TOPC DB-9 CONNECTOR

IBM-COMPATIBLE PC

PATCH PANELPORT 8 DB-9 CONNECTOR

DB-25 CONNECTOR

EXTERNAL AT COMMAND SET MODEM


RS-232 Alarm Interface Unit ConnectionThe AD2096A Alarm Interface Unit (AIU) can beconnected to any one of the eight RS-232 ports on theMegaPower 48 patch panel. The MegaPower 48 port isconnected to the RJ-45 COM OUT receptacle on therear panel of the AD2096A via a seven foot modularcable. For connections greater than seven feet, twosingle, 8-pin terminal boxes are used with 3 wire, 18AWG, shielded cable. Maximum cable length = 1000feet (305m).

The AD2096A rear panel also contains a DIP switch forselection of normally open or normally closed status forthe alarm contact relays, and a DIP switch that selectsthe appropriate alarm contact group (1-64, 65-128, 129-192, etc.). The MegaPower 48 system can accept up to512 RS-232 alarm inputs. Each AD2096A can beconnected to up to 64 alarm contacts. Up to sevenadditional AD2096A units can be cascaded via the RJ-45 COM IN receptacles to accommodate additionalalarm contacts. See Drawing 18, Page 26 for a typicalMegaPower 48 RS-232 port to AD2096A connection.

Additional AD2096A Documentation● AD2096A Alarm Interface Unit Installation and

Operating Instructions –part number 8000-0888-01

RS-232 Peripheral Interface Port ConnectionMegaPower 48 embedded software and S3 system setupsoftware provide the user with a system option to enablea Peripheral Interface Port (PIP). For MegaPower 48release 1.0, a PIP will connect to an AD100 series videorecorder interface for control of up to 1024 videorecorders. Control is implemented with the AD2088keyboard. The MegaPower 48 RS-232 PIP connects toan AD-100XA (or AD100XA-1) Recorder Controllervia a seven foot modular cable with a DB9M connector.The DB9M connects to the RS-232 port on theAD100XA. See Drawing 19, Page 27 for a typicalMegaPower 48 RS-232 port to peripheral interface portconnection.

Additional PIP Documentation● AD100 Series Recorder Controller & IR Interface

Hookup / Software Utility Installation & OperatingInstructions -part number 8000-1796-01

Direct Alarm and Relay Connections

Relay OutputsThe MegaPower 48 patch panel provides a section fordirect connection to two normally open or normallyclosed relay outputs for switching of auxiliary devicessuch as lights, gates, audio alerts, recorders, etc.

Patch Panel AlarmsThe MegaPower 48 patch panel also provides 16 screwterminals and corresponding ground returns for directconnection to normally open alarm contacts. Theseconnections are referred to as “patch panel” alarms.Patch panel alarms are connected with shielded, two-wire cable. Both the shield and ground wires must beconnected to the ground terminals in the patch panelalarm section.

System Alarm HandlingThe total alarm handling capability of MegaPower 48 isprovided by 16 patch panel alarms, 512 RS-232 alarmswired through the AD2096A Alarm Interface Unit, 192dome alarms (up to 48 domes, with four alarm contactsper dome), and up to 48 video loss alarms that aregenerated when a loss of video sync is detected at avideo input. See Drawing 20, Page 28 for typical directalarm and relay connections.

Technical SupportIf you need assistance, please contact your Sensormaticrepresentative.


Drawing 18: AD2096A

Drawing 18: RS-232 CommunicationsPatch Panel to AD2096A Alarm Interface Unit to Alarm Contact

ALARM INPUT ON AD2096A

ALARM CONTACT

PATCH PANELRS-232 PORT

AD2096A ALARMINTERFACE UNIT


Drawing 19: Video Recorder Control

Drawing 19: RS-232 CommunicationsVideo Recorder Control via AD2088 Keyboard

VIDEO RECORDERSAD100 SERIES RECORDERCONTROLLER UNITS

AD2088 KEYBOARD

PATCH PANEL RS-232 PORTS

IR EMITTER CABLE


Drawing 20: Alarm & Relay Sections

Drawing 20: Patch Panel Alarm & Relay Sections

PATCH PANEL ALARMS SECTIONTWO 16-POSITION SCREW TERMINAL BLOCKS

ALARM CONTACT

PATCH PANELRELAY TERMINALS

RELAY INPUT TO VCR

MegaPower 48 System Troubleshooting

Troubleshooting 29

Troubleshooting Guide

TROUBLESHOOTING GUIDEPROBLEM POSSIBLE CAUSE SUGGESTED ACTION

General System Problems

check connection to patch panelcheck fuse on transformer

incorrect voltage to MEU

check voltage at wall outletincorrect MEU installation check that MEU clicks when re-attached.loose connections tighten terminal screws

press reset switch on patch panel

system inoperativesymptoms:● AC power LED off● UOP LED not blinking● system not updating● MEU fan not audible faulty MEU

replace MEUincorrect port configurations change port parameters on system and PCfaulty RS-232 cable swap cable

can’t upload or download systemparameters

faulty PC com port swap PC

Video Problemsfaulty video output channel switch video output cable to another BNC.faulty video input call a known-good camera to monitor.faulty video cable swap cable to monitor

no video on monitor (blank screen)

faulty monitor swap monitor with anothermonitor connected to videooutputs 9-16

connect Monitors to video outputs 1-8 for text

title positioning off screen enter 50 F2 (start title positioning)

no alphanumeric display on monitor

video locked up press system reset button on patch panel.black horizontal lines through video,or video not stable.

faulty camera sync or videooutput

swap camera with another

monitor 16 will not display video video loss detection enabled disable video loss detection through softwareor call monitors 1-15 for display of video.

camera not terminated properly check termination of cameravideo too bright, to dark, or poorcolor quality camera iris not adjusted

properlyadjust camera iris using calibrated monitor

Keyboard Communication Problemsincorrect interface wiring check wiring at terminal box.incorrect port/keyboard settings match RS-232 port and keyboard parametersfaulty keyboard cable swap cable

check voltages at terminal box.

check transformer voltage

incorrect voltage to keyboard

check voltage at wall outlet (site dependent)

keyboard can’t switch video

faulty keyboard swap keyboardkeyboard responds to some, but notall keys.

keyswitch setting may beinappropriate.

verify appropriate keyswitch settings for eachset of operations.

cannot access menu programming menu access disabled forkeyboard

enable menu access for keyboard throughpriority level programming.

pan/tilt cameras move and/or. cursorscrolls continuously in menu mode.

faulty joystick run keyboard diagnostic test to verify joystickoperation.

MegaPower 48 System Troubleshooting

30 Troubleshooting

TROUBLESHOOTING GUIDEPROBLEM POSSIBLE CAUSE SUGGESTED ACTION

Dome Communication Problemsincorrect wiring check Manchester or RS-422 wiring pathsincorrect SensorNet termination Check SensorNet network documentation for

appropriate termination points..check group addressing switches on codetranslator.

incorrect addressing

check dome addresses.faulty composite cable swap cable with anotherfaulty code distributor ortranslator

swap device with another

loose connections tighten terminal screws

dome not responding to keyboardcommands

faulty dome swap dome with another

System Alarm Problemsfaulty wiring check contact to patch panel wiring pathincorrect alarm programming 1. associate alarm with camera

2. associate alarm with monitor3. arm the monitor

alarm signal missing during alarmevent

incorrect port setting on alarminterface unit.

correct port setting through systemprogramming.

constant alarm contact shorted repair or replace contact.alarm too long or too short incorrect alarm programming check dwell time selected

Paging Problemsdual use of port 8 remove any device connected to the port 8 RJ-

45 receptacleincorrect port parameters program port per Appendix G of Programming

& Operating manual.inappropriate phone system connect to analog telephone line

paging function inoperative

incorrect paging programming Perform menu programming per Appendix G ofProgramming & Operating manual

Declaration of Conformity 31

Declaration of Conformity

Manufacturer:

Sensormatic Video Systems Division Sensormatic Video Systems Division1 Blue Hill Plaza 6795 Flanders DrivePearl River, NY 10965 USA San Diego, CA 92121

Sensormatic Electronics CorporationState Rd. 110 Km 5.8Poblado, San AntonioAguadilla, P.R. 00690

Declares, that the product(s) listed below:

Equipment Type: Matrix Switcher/Controller System

Product Name: MegaPower 48

Model Number: VR48*

* Depending on system configuration the model numberindicated above will be modified by additional coding.

complies with the standards:EN55022 (Class B) Emissions

EN50130-4 Immunity

EN60950 Safety

Additional information:

These products herein, comply with the requirements of the EMC Directive 89/336/EEC, and with the Low VoltageDirective (LVD) 73/23/EEC. The equipment was tested in a typical configuration.

Pearl River, NY, USA 15 December, 2000

Harold D. Johnson, Ph. D.Director of Engineering

European Contact: Sensormatic France S.A.

7, rue Alexis de Tocqueville

Parc de Haute Technologie,

92183 ANTONY CEDEX

32 Product Specifications

MegaPower 48 Product Specifications

System Specification

Video Subsystem

Video Inputs: ................................................ 48 inputsSwitched Outputs:......................................... 16 outputsVideo Text Overlays:.................................... Standard on 8 Video OutputsVideo Bandwidth: ......................................... + 10 Mhz (1 input to 1 output)

+ 8 Mhz (1 input to 16 outputs)Frequency Response: .................................... ±1.0dB, 0 to 6 MhzSignal to Noise Ratio: .................................. -60 dB (Vpp vs Vrms)Composite Output Voltage: .......................... ≤ 0.5 dBAverage Output Voltage: .............................. ± 250 mVCross Talk:.................................................... Adjacent Channel: -55 dB typical at 3.58 to 4.43 Mhz

Input to Input: - 70 dB typical at 3.58 to 4.43 MhzDifferential Phase: ........................................ ≤ 2.0 %Differential Gain: .......................................... ≤ 2.0 %

Using Pulse & Bar GeneratorField Tilt:........................................................≤ 2.0 %

Using Pulse & Bar GeneratorLine Tilt: ....................................................... ≤ 2.0 %

Using Pulse & Bar GeneratorGain: ............................................................. Unity ± 1 dBReturn Loss (input/output):........................... > 40 dBSwitching: ..................................................... Full Cross Point MatrixSwitching Time:............................................ < 20 milliseconds

Video Input Matrix

Cross Points: ................................................. 48 inputs by 16 outputsInput Impedance: .......................................... 75 ohms terminated

Video Output Overlay

Alpha-Numeric Modes:Video Standard Text Area Pixels per CharacterNTSC 18 lines of 32 characters 12 High by 8 WidePAL 22 lines of 32 characters 12 High by 8 Wide

TV Standards: ............................................... NTSC and PALCharacter Attributes:..................................... Character Intensity, 8 levels

Text Background: transparentCharacter Sets: .............................................. English (standard)

Display Area Positioning: ............................. X direction – 10 µsec after the end of the horizontal sync pulseY direction – 29 lines from the end of vertical sync pulse

Product Specifications 33

System Communications

External Device CommunicationsS-Net 485 Ports (6): ...................................... RS-485, transformer isolated, 230.4 Kb/s, surge protectedRS-422 Ports (6): .......................................... RS-422, SEC protocol, full-duplex, asynchronous, 4800 Baud surge protectedManchester Port (1): ..................................... AD protocol, transformer isolated, surge protectedRS-232 Ports (8): .......................................... 9600 Baud Rate (selectable, 1200, 2400, 4800 and 9600) surge protectedEthernet Port: .................. ............................. 10 Mb/s, surge protected

Optional External Communication Code DistributorsAD1691 ............................. .......................... Manchester Code DistributorsAD1691F-1....................... ........................... Manchester Code DistributorsAD2083-02B .................. ............................. RS-422 SEC Code DistributorsAD2083-02B-1 ................ ............................ RS-422 SEC Code Distributors

Central ProcessorProcessor: ..................................................... High speed Motorola MPC860T @ 25 MhzMemory: ....................................................... 1M x 32 RAM

512K x 16 non-volatile RAM768K x 32 ROM

Communication Ports: .................................. RS-232 RJ-45 connector, DB9 connectorEthernet, RJ-45 connector

Operating System:......................................... .pSOS

Electrical Specifications

Power Supply InputPower Source:............................................... ...24 VAC External TransformerPower Source Input:..........................................90-132 VAC, 47 – 63 Hz 195-253 VAC; 47 – 63 HzPower Consumption:..................................... ...20 WattsPower-on in-rush current: ............................. ...10 A (120 VAC); 5 A (230 VAC)

Mechanical Specifications

DimensionsDepth: ...................... .... ................................ 8.43cm (3.50”)Width: ...................... .... ................................ 43.69cm (17.25”)Height: ..................... .... ................................ 50.85cm (20”)

WeightShipping Weight: ..... ....... ............................. 36.3 kg. (16.5 lb.) max.

34 Product Specifications

Environmental Specifications

Operating Temperature ................................. 0°C to + 50°C (32°F to 122°F)Humidity: ................. ... ................................. 5 to 95% non-condensingStorage Temperature:.................................... -40°C to 70°C (-40°F to 155°F)

Standard Product Features

Color Video Text Overlay ............................ Standard on eight of the sixteen video outputsSwitching: ................ .................................... Vertical interval switchingData Communication Ports: .......................... 8 x RS-232

1 x 10 Mb Ethernet port6 x SensorNet port6 x RS-422 port1 x Manchester port

Alarm Inputs:.................................................16 x Normally Open ContactsRelay Outputs:...............................................2 x Form C RelaysAC Power Interface: .................................... IEC style connector; Multi-national line cord options

User InterfaceKeyboard Compatibility: .............................. AD2088, AD2079, and ADTTE seriesProgramming Environment........................... Operator accessible on-screen menus for all functionsAdministrative & Configuration: .................. Via on-screen menus

Service Related Features● Easy to install using suspended vertical wall-mount technique, optional rack mount kit● Easy to service by non-technical personnel● Built-in diagnostics● Software updates down-loaded through a PC● Surge protection on all Alarm, Relay, Ethernet, RS-232, SensorNet, RS-422 and Manchester lines● External transformer with IEC line cord● Unit Operating Properly (UOP) LED (Viewable on patch panel)● Power LED (viewable on patch panel)● Four Diagnostic LEDs (viewable on patch panel)● +/- Voltage LEDs viewable on patch panel● Peripheral control of SensorNet, SEC RS-422, RS-232, and AD Manchester devices without the use of any external

interface units

Product Codes

Sensormatic Product Codes VR48NC: ......................... 48 x 16 Matrix Switch with no Controller VR48KB: ......................... 48 x 16 Matrix Switch with AD2088 VR48TT:.......................... 48 x 16 Matrix Switch with ADTTE

Product Specifications 35

Compatible Product Listing

Non-CE Approved

CodeDrivers

Keyboards AlarmInput

RelayOutput

RDUs Domes GUIs P & T

AD2083 AD2079 AD2096A AD2031 AD1641M Series Cobra Series Excalibur

AD5568

AD1240

Series

AD1691 AD2088 AD2032 AD1646M

Series

Tracker 2Series

AD1241

Series

ADTTE AD2033 AD1684B SpeedDomeSeries

AD1242

Series

AD1686B

AD1689B-8

CE Approved

CodeDrivers

Keyboards AlarmInput

RelayOutput

RDUs Domes GUIs P & T

AD2083-02B-1 AD2088-1 AD2096-1 AD2031-1 AD1641MSeries

Tracker 2 Series ExcaliburAD5568

AD1240Series

AD1691F-1 AD2079-1 AD2032-1 SpeedDome Series AD1241Series

ADTTE AD2033-1 AD1242Series

Approvals

Safety ApprovalsUL.............. .................................... UL1950CUL or CSA................................... CSA 22.2, No. 950-95TUV........... .... ................................ IEC 950, EN60950CE.............. ..... ............................... IEC 950, EN60950

EMI StandardsConducted Emissions ..................... EN55022Radiated Emissions..........................EN55022Immunity ... ..... ............................... EN50130-4

36 Index

Index

A

AD1691 Code Distributor ∙ 6AD2083-02B Code Translator ∙ 6AD2096A Alarm Interface Unit ∙ 9alarm and relay connections ∙ 9alarms section ∙ 3

B

backbone configuration ∙ 5

C

cable management bracket ∙ 2cable networks ∙ 5communications section ∙ 4

D

daisy chain configuration ∙ 5declaration of conformity ∙ 33diagnostics section ∙ 4disengaging the patch panel ∙ 2

F

features ∙ 1

I

installation kit ∙ 1installation template ∙ 1installation, box 1 ∙ 1installation, box 2 ∙ 1

M

manchester communications ∙ 6mechanical installation ∙ 1modem ∙ 8modem section ∙ 4

P

patch panel ∙ 1port expander ∙ 8power requirements ∙ 5power section ∙ 4product specifications ∙ 34

R

recommended tools ∙ 1red shipping knobs ∙ 1relay section ∙ 3RS-232 communications ∙ 8RS232 section ∙ 4RS-422 communications ∙ 6

S

sensornet communications ∙ 6star configuration, ∙ 5startup diagnostics ∙ 2system accessories ∙ 4system integration ∙ 5system programming ∙ 4

T

technical support telephone numbers ∙ 9terminations ∙ 5transformer ∙ 2troubleshooting guide ∙ 31

V

video connections ∙ 5video inputs section ∙ 3video outputs section ∙ 3

W

wall bracket ∙ 1

Sensormatic Video Systems Division1 Blue Hill Plaza

Pearl River, New York, 10965

PN 8000-1803-51, Revision B

MegaPower 48 Installation Manual - American...

Documents

Transcript of MegaPower 48 Installation Manual - American...