Nirmala Rajbhandari: Dr. Paras Mani Pradhan Presentation Jan 23 2015(1)
Meet The Team Electrical Engineers (EE) Project Manager – Zachary Prisland Battery Specialist and...
-
Upload
juniper-newman -
Category
Documents
-
view
216 -
download
0
Transcript of Meet The Team Electrical Engineers (EE) Project Manager – Zachary Prisland Battery Specialist and...
Team #2 Solar Car Project Senior Design 2010 - 2011
Team #2 Solar Car ProjectSenior Design 2010 - 2011
Meet The TeamElectrical Engineers (EE) Project Manager Zachary PrislandBattery Specialist and Treasurer Shishir RajbhandariPower Technical Lead James Barge
Mechanical Engineers (ME)Mechanical Lead and Team Organizer Keith DalickTest Engineer Adrian CiresKing of Suspense(ion) Emiliano Pantner
Meet The TeamIndustrial Engineers (IE)Industrial Lead Nelson GermanQuality Technician Rajat PradhanLead Manufacturer and Secretary Amanda Roberts
Graduate Advisor Chris Widener
American Solar ChallengeFundamental VisionThe American Solar Challenge (ASC), hosted by the Innovators Education Foundation, seeks to promote and celebrate educational excellence and engineering creativity. Fueled by the spirit of friendly competition and teamwork, the ASC champions the creative integration of technical and scientific expertise across a range of exciting disciplines.Old Design
Fiberglass ExteriorSteel FrameFour wheel designMotor on one of the rearBrakes on other threeLead-Acid Batteries
Progress in Phase 1Revamped electrical systemNew BatteriesCharging SystemReworked DashboardStripped off FiberglassWorked on suspensionRemoved one tire
CapabilitiesRequiredDesiredMoving vehicle powered with stored energy in batteries
Ability to carry a driver and provide control over the vehicleSolar cells that can be used to charge batteries
Shell or covering for the frame of the vehicleVehicle capable of achieving 65 mph for extended periods of time using only battery powerAbility to carry driver comfortably and safelySolar cells able to reduce power drain from batteries while vehicle is in motion Shell that reduces wind resistance while increasing horizontal surface areaFunctional and Non-Functional RequirementsMechanical and ElectricalFunctional Requirements - MEImplement parking brakeIntegrate regenerate braking with mechanical brakeDesign body of the car (shell)Redesign roll cage to meet safety requirements
Functional Requirements MEReduce stress on drive motor
Back rightBack leftFunctional Requirements MEImprove front (below) and rear (below right) suspensions
Non-Functional Requirements MEDriver cockpit equipped with outside air circulationRoll cage must be padded with energy-absorbing materialEnsure steering column meets safety requirements
Non-Functional Requirements MEImprove method of securing batteries to carImprove electronics housing enclosure
Functional Requirements EESelection of solar cellsDesign solar array integration Design a driver interface that allows drive system engagement from the cockpit.Design charging system to interface the solar arrays with the batteriesAllow charging of batteries while in motion
Non-Functional Requirement EEImplement a warning light/safety system showing when power is engaged.Add road safety functions (lights, horn)ConstraintsMechanicalMechanical ConstraintsDimensions for carLength 5.0 mWidth 1.8 mHeight 1.6 mWeight RequirementNo total minimum80 kg DriverBallast for supplement
Mechanical ConstraintsBody ConstraintsHard tow pointMinimum three (3) tiresMaximum of two body parts when stationaryMoving parts must be covered
CockpitMain goalSeat position27 degrees minimumNo more than 15cm from center5 point seat beltRoll cage5 cm from driver helmetFoamEncompass entire driverMechanical ConstraintsVisibility70cm eye level100 degrees from centerWindshield shatter resistantRear viewing systemBrakingBalancedDual systemParking brake Performance testStabilityFigure 8 TestSlalom Test
ConstraintsElectricalElectrical ConstraintsNatural solar radiation received directly by the solar array is the only source of energy that can be used for propulsion.
Vehicle operation must be under the sole control of the driver.
Electrical ConstraintsSolar Arrays cannot exceed a maximum of 6.00 m2.Maximum of 6 different types of panels can be used.Cells must be from approved list or approved by ASC.
Electrical ConstraintsLiFePO4 Batteries are limited to a weight of 30kg.All batteries must have protection circuitry appropriate for the battery technology used.All battery modules, battery protection circuitry, and main fuses must be fully contained in enclosures that are electrically isolated from the car.Electrical ConstraintsBattery enclosures must be equipped with a forced ventilation system.The car must be equipped with a single throw, manually operated, switch to quickly isolate the battery, motor, and array from each other and the electrical system of the vehicle.Electrical ConstraintsMust be equipped with an electrical cutoff switch that can be externally activated in emergency situations.All electrical cables must be properly sized to expected system currents.All lighting must be clearly visible from 30 m.Test PlansMechanicalTest PlansFinite Element Method (FEM)Used to test much of the mechanical requirements
Example of FEM on woven cloth (I Mechanica)Test PlansDriver CockpitVentilation TestSeatMeasurement/Positioning TestImplemented hand brakeRedesigned brake system for automatic regeneration
Test PlansSuspensionRear suspension Reduce stress on drive motorFront Suspension
Roll cage
FEM analysis of vehicle suspension (Penmethsa)Test Plans - MEDesign composite bodyShell over existing chassisDrag Area Test
Flow visualization using FEMTest PlansElectricalTestsBatteries for defects or unsafe operating voltageMotorSolar Arrays for output voltage potentialPower Charger (self-test)Battery Protection SystemControl Interface SystemEnsure protection circuit and fuses are electrically isolated from the car
TestsMain Power Switch and External Power Cut-Off SwitchRoad safety lighting devicesHornRegenerative Braking SystemEnsure electrical shock hazards are protected from inadvertent human contactTest Drive!!!
Questions
Work CitedAmerican Solar Challenge. (2010, September 1). Regulations. Retrieved September 23, 2010, from American Solar Challenge: .I Mechanica. FEM of woven cloth. Retrieved September 27, 2010 from . Penmethsa, Harish. (2009, June 4). Frequency of Time Response Analysis on Shock Absorber. Retrieved September 27, 2010 from .