Mecal MSEP/F Two-Post Die Pneumatic end feed€¦ · MSEP/F MSEP/S Two-Post Die Pneumatic left...
2
Azienda con Sistema Qualità certificato N° 501001810 Mecal S.r.l. Strada per Felizzano 18 I - 15043 Fubine (AL) ph. +39 0131 792792 fax +39 0131 792733/4 www.mecal.net Specifications MSEP/F Pneumatic end feed Two-Post Die Two-Post Die MSEP/F ID MSEP/F DESCRIPTION Pneumatic end-feed two-post die CRIMPING HEIGHT 190/212 mm (7.48/8.346’’) STROKE 50/40 mm (1.968/1.575’’) TERMINAL PITCH not binding TERMINAL THICKNESS above 1.5 mm (0.059’’) WIRE SECTION up to 75 mm 2 (3/0 AWG) FEEDING SYSTEM air pressure 5/6 bar WEIGHT 17 Kg (37.4 lb) DIMENSION (mm) W 170 x H 210 x D 450 DIMENSION (‘’) W 6.69 x H 8.26 x D 17.7 Two-post crimping die for big terminals linked “ end to end ”, rolled over a reel, with thickness > 1.5mm, wire section up to 75mm 2 . Terminal pitch non binding. Continuous crimping height adjusting system. Pneumatic “ end-feed ” feeding system. All the wearing parts can be repla- ced without removing the applicator from the press. Can be fitted to any crimping press having a crimping height (measured from the die moun- ting plate to the press coupling when at Bottom Dead Center) of 212mm (see Mecal press P104) or 190mm (see Mecal press P150 and P200). It is supplied with a complete technical documentation containing all the information needed to safely use and correctly maintain the equip- ment. Upon request, a capability study (including a picture of a sectioned crimped terminal) can be performed. Cycle counter non available. Produced under a quality Management System certified to ISO 9001 and 14001 (TÜV). Specifications subject to change. Consult Mecal S.r.l. for latest specifications.
Transcript of Mecal MSEP/F Two-Post Die Pneumatic end feed€¦ · MSEP/F MSEP/S Two-Post Die Pneumatic left...
Azienda con Sistema Qualitàcertificato N° 501001810
Mecal S.r.l.Strada per Felizzano 18I - 15043 Fubine (AL)ph. +39 0131 792792fax +39 0131 792733/4www.mecal.net
Specifications
MSEP/FPneumatic end feedTwo-Post Die
Pneumatic end-feed
Two-Post DieMSEP/F
MSEP/STwo-Post Die
Pneumatic left side-feed
IDMSEP/F
DESCRIPTIONPneumatic end-feed two-post die
CRIMPING HEIGHT190/212 mm (7.48/8.346’’)
STROKE50/40 mm (1.968/1.575’’)
TERMINAL PITCHnot binding
TERMINAL THICKNESSabove 1.5 mm (0.059’’)
WIRE SECTIONup to 75 mm2 (3/0 AWG)
FEEDING SYSTEMair pressure 5/6 bar
WEIGHT17 Kg (37.4 lb)
DIMENSION (mm)W 170 x H 210 x D 450
DIMENSION (‘’)W 6.69 x H 8.26 x D 17.7
Two-post crimping die for big terminals linked “ end to end ”, rolled over a reel, with thickness > 1.5mm, wire section up to 75mm2. Terminalpitch non binding. Continuous crimping height adjusting system. Pneumatic “ end-feed ” feeding system. All the wearing parts can be repla-ced without removing the applicator from the press. Can be fitted to any crimping press having a crimping height (measured from the die moun-ting plate to the press coupling when at Bottom Dead Center) of 212mm (see Mecal press P104) or 190mm (see Mecal press P150 and P200).It is supplied with a complete technical documentation containing all the information needed to safely use and correctly maintain the equip-ment. Upon request, a capability study (including a picture of a sectioned crimped terminal) can be performed. Cycle counter non available.
Produced under a quality Management System certified to ISO 9001 and 14001 (TÜV). Specifications subject to change. Consult Mecal S.r.l. for latest specifications.
Azienda con Sistema Qualitàcertificato N° 501001810
Mecal S.r.l.Strada per Felizzano 18I - 15043 Fubine (AL)ph. +39 0131 792792fax +39 0131 792733/4www.mecal.net
SpecificationsIDMSEP/S
DESCRIPTIONPneumatic side feed two-post die
CRIMPING HEIGHT190/212 mm (7.48/8.346’’)
STROKE50/40 mm (1.968/1.575’’)
TERMINAL PITCHnot binding
TERMINAL THICKNESSabove 1.5 mm (0.059’’)
WIRE SECTIONup to 75 mm2 (3/0 AWG)
FEEDING SYSTEMair pressure 5/6 bar
WEIGHT17 Kg (37.4 lb)
DIMENSION (mm)W 450 x H 210 x D 150
DIMENSION (‘’)W 17.7 x H 8.26 x D 5.9
Two-post crimping die for big linked terminals rolled over a reel to be unrolled “ left to right ”, with material thickness > 1.5 mm., wire sec-tion up to 75 mm2. Terminal pitch not binding. Continuous crimping height adjusting system. Pneumatic “ side-feed ” feeding system.All the wearing parts can be replaced without removing the applicator from the press. Can be fitted to any crimping press having a crimpingheight (measured from the die mounting plate to the press coupling when at Bottom Dead Center) of 212mm (see Mecal Press P104) or 190mm(see Mecal press P150 and P200). It is supplied with a complete technical documentation containing all the information needed to safely useand correctly maintain the equipment. Upon request, a capability study (including a picture of a sectioned crimped terminal) can be performed.Cycle counter non available.
Produced under a quality Management System certified to ISO 9001 and 14001 (TÜV).
MSEP/FTwo-Post Die
Pneumatic end-feed
MSEP/STwo-Post Die
Pneumatic left side-feed
Two-Post DieMSEP/S
Pneumatic left side feed
Specifications subject to change. Consult Mecal S.r.l. for latest specifications.
