【Material】- For Mommy Pearl white/button/4-5mm ( item no. 4799101 ) 145 pcs

Wooden beads ( item no. 4717101 ) 36 pcs

Coral red/chips ( item no. 10414-LE-718 ) 42 pcs

Shell blue/round ( item no. 10653-LE-183 ) 19 pcs

Toggle clasp set 2 pcs

Jump ring 4mm 2 pcs

Finding w/3 loops ( item no. 25788-93 ) 2 pcs

Stringing wire 0.38mm ( item no. JW14T-0 ) 80cm 1 pcs

Stringing wire 0.38mm ( item no. JW14T-0 ) 30cm 3 pcs

Crimp 8 pcs

Wooden beads ( item no. 4717101 ) 60 pcs

Coral red/chips ( item no. 10414-LE-718 ) 6 pcs

Coral white/chips ( item no. 11068-LE-005 ) 34 pcs

Shell blue (wooden)/round ( item no. 10653-LE-183 ) 2 pcs

Shell blue/round ( item no. 10653-LE-183 ) 2 pcs

Cat-eye white/round ( item no. 1825310 ) 29 pcs

Jump ring 4mm 2 pcs

Crimp 2 pcs

Stringing wire 0.38mm ( item no. JW14T-0 ) 50cm 1 pcs

Clasp spring ring silver set 1 pcs

Double cup connector ( item no. 1921-42 )-bead tip 2 pcs

Supplemax clear cord 0.3mm 30cm 2 pcs

【Tools】 Cutter Pliers, Long and Round Nose Pliers

【Material】- For Me (Necklace + Ring)

Free DIY LessonE a s y T o M a k e & P r o u d T o W e a r

Me & Mommy Necklaces, Bracelet, Ring

【Instruction】Mommy--Necklace / Bracelet

Pearl

Wo

oden beads 36pcs

Shell Blue/round 19pcs

Coral Red 42pcs

Jump ring Finding w/3 loops

Toggle Clasp Step Take one end of stringing wire (80cm) and thread through crimp, then through the toggle clasp and back through the crimp (leave about 1.5~2cm). Then use long nose pliers to close the crimp (make sure it’s tight).

Step Thread the 145pcs pearls onto the stringing wire. finish by threading a crimp and the other half of the clasp just like you did in step 1.

Step Similar to steps 1 and 2, thread the 3 strands of beads as shown. then combine the findings with jump rings at both ends.

Stringing wire

Crimp

Mommy -- Necklace / BraceletApproximate Crafting Time: 1 hourMe -- Necklace + RingApproximate Crafting Time: 1 hour

Designed by Jennifer Howe, www.ecstaticjewelry.com

Skill

Level 1

【Instruction】Me--Necklace + Ring

Cat-eye white/4mm

Tip--How to make the knot and hide it

-Start

-end with knots

Make two knots nice and tight atthe same place.

Thread one end back to the

bead then pull until the knot is inside of the bead.

Shell blue (wooden)

Wooden

bead

s 30

pcs

Shell Blue

Coral White x 17pcs

From Step 1

Coral Red x 3pcs

Cat-eye white

Step - Necklace

Thread the beads as shown, and at the end thread double cup connector (bead tip). Squeeze the long nose pliers firmly to flatten the crimp bead. then hide it in the double cup connector (bead tip) and close the bead tip with long nose pliers. Finish by addingthe clasp set with jump rings.

Step - Necklace Squeeze the long nose pliers firmly to flatten the crimp bead. then hide it in the double cup connector (bead tip)and close the bead tip with long nose pliers.

Step - Necklace Take one 30cm supplemax clear cord and start at , follow the graphic as shown. Make the knot at and hide it in the closest bead.

Step - Ring Take one 30cm supplemax clear cord and start at , follow the graphic as shown. Make the knot at and hide it in the closest bead.

v

v

v

v

(Note: the graphic shows the single thread with two colors, this is just to illustrate which portion goes through which bead.)

double cup connector (bead tip)

Crimp

Stringing wire

v

v

Shell blue (wooden) Cat-eye white/4mm

1

2

3

9

10

(Note: The ring size depends on your finger size, add more beads to make it bigger)

** I would like to thank Beverly's for the sample beads. Since 1968, Beverly's has continued to be an indus-try leader in Crafts, Fabrics, home decor and much more. For further information please visit www.beverlys.com.