MC-V3MCUS Rev. 6 - mis-implants.com · 12° Micro-rings Micro-rings on the neck of the implant are...
Transcript of MC-V3MCUS Rev. 6 - mis-implants.com · 12° Micro-rings Micro-rings on the neck of the implant are...
®
M A K E I T S I M P L E
Implant System
MC
-V3M
CU
S R
ev. 6
P. 18-19
P.20-21
P. 15-17
P. 14
P. 10-13
P. 8-9
P. 6-7
P. 4-5
MIS Warranty:
MIS exercises great care and effort in maintaining the superior quality of its products. All MIS products are guaranteed to be free from defects in material and workmanship. However, should a customer find fault with any MIS product after using it according to the directions, the defective product will be replaced.
Warning: Products should be used by licensed dentists only.
Introduction
Advantages
Narrow Platform Implants (Ø3.30mm)
Standard Platform Implants (Ø3.90, Ø4.30, Ø5mm)
Gain of Bone Volume
Conical Connection Surgical Kit
Insertion Tools
Package Contents
Table of contents.
© MIS Implants Technologies Ltd. All rights reserved.
The V3 implant system is the outcome of an
exceptionally high-level R&D process that has
resulted in an implant that is simple, easy-
to-use and offers enhanced functionality and
performance. The V3 conical connection implant
features built-in design characteristics which
may provide biological benefits for hard and soft
tissues and promote esthetic results.
6.
V3 conical connection implants
The unique b io logica l and mechanical features of the V3 implant were designed to allow for additional space for bone growth, which may support more stable surrounding soft tissue and more esthetic restorations.
All V3 implants, superstructures and tools are color-coded for easy identification of platform sizes.
Advantages.
Purpleindicates a Standard platform
Blue indicates a Narrow platform
Toll Free 1-(866) 797 1333
12°
Micro-ringsMicro-rings on the neck of the implant are designed to facilitate an increase in bone to implant contact (BIC). This design concept has been reported to be associated with less crestal bone loss when compared with other implant design features.
Conical connectionThe 12° conical connection was engineered to create an ultimate seal and ideal connection between the implant and abutment with built-in platform switching, reducing micro-movements.
Implant neckThe triangular shape at the V3 neck was engineered to provide high immediate crestal stability and potential bone preservation. Anchorage may be achieved at three points without compromising crestal primary stability.
Platform switchingThe V3 implant incorporates the platform-switching design concept. Implants with a platform-switched configuration have been shown to exhibit less bone loss when compared to non-platform-switched implants, which may lead to soft tissue preservation and growth.
Designed for more boneThe compression-free gaps around the coronal area of the V3 were engineered to provide a reservoir for blood pooling and the formation of blood clots. These conditions are both required for optimum implant integration and bone growth.
Flat apexThe flat apex is designed to allow good grip into bone, especially in immediate placement procedures.
Surface treatmentThe surface roughness and micro-morphology is a result of sandblasting and acid etching. This proven MIS surface technology leads to a high level of cleanliness, which leads to effective osseointegration. This is one of the key factors which contribute to long-lasting clinical success.
Engineered for bone stress reduction The gaps around the sides of the implant neck were designed to result in an open, compression-free zone. Crestal bone loss may be minimized by reducing stress in the cortical bone.
Toll Free 1-(866) 797 1333
16mm11.50mm 13mm10mm
V3-10330 V3-13330 V3-16330V3-11330
8.
Ø 4mm Ø 4.8mm
CC1-00277
Ø3.30mm
CN-H0333CN-H0433CN-H0533CN-H0633CN-H0833
Ø 3.3mm
3, 4, 5, 6, 8mm
CN-HS340CN-HS440CN-HS540CN-HS640CN-HS840
Ø 4mm
3, 4, 5, 6, 8mm
CN-HA248CN-HA348CN-HA448CN-HA548CN-HA648CN-HA848
Ø 4.8mm
2, 3, 4, 5, 6, 8mm
Gingival heights:
Gingival heights:
Gingival heights:
Narrow PlatformScrew type implant range
Length
Type
V3 short motor insertion tool, narrow platform
V3 long motor insertion tool, narrow platform
Insertion Tools
V3 short ratchet insertion tool, narrow platform
V3 long ratchet insertion tool, narrow platform
Implant cover screw and healing caps
CT-NSM30 CT-NLM30 CT-NSR30 CT-NLR30
Toll Free 1-(866) 797 1333
800-1000
600-800
Ø1.90 Ø3.30Ø2.40 Ø2.40
200-400
200-400
V3-10330
V3-11330
V3-13330
V3-16330
Ø3.30mm
Ø3.30mm
Ø 3.30mm
Ø 3.30mm
Ø 3.30mm
Ø 3.30mm
Ø2.3
Ø 3.2
Ø 2.50
Ø 3.30
Ø2.75
Catalog No. Dimensions
length 10mm
length 11.50mm
length 16mm
length 13mm
Titanium Alloy Ti 6Al 4V ELISand-Blasted and Acid-Etched
Narrow Platform
Implant Procedure
The drilling sequence is illustrated using 11.50mm implants.
Procedure recommended by MIS cannot replace the judgment and professional experience of the surgeon.
Drilling Speed (RPM)
Diameter
TorqueMax. 45N·cm
Final drill For bone type 1&2
Final drill For bone type 3&4
Toll Free 1-(866) 797 1333
16mm11.50mm 13mm10mm8mm
Ø3.90mm
Ø4.30mm
Ø5mm
V3-10390
V3-10430
V3-10500
V3-08390
V3-08430
V3-08500
V3-13390
V3-13430
V3-13500
V3-16390
V3-16430
V3-16500
V3-11390
V3-11430
V3-11500
CT-SSM30
CT-SLM30
CT-SSR30
CT-SLR30
10.
CC1-00315 CS-H0339CS-H0439CS-H0539CS-H0639CS-H0839
Ø 3.9mm
3, 4, 5, 6, 8mm
CS-HS248CS-HS348CS-HS448CS-HS548CS-HS648CS-HS848
Ø 4.8mm
2, 3, 4, 5, 6, 8mm
VS-HS358VS-HS458VS-HS558VS-HS658VS-HS858
Ø 5.8mm
3, 4, 5, 6, 8mm
Gingival heights:
Gingival heights:
Gingival heights:
V3 short motor insertion tool, standard platform
V3 long motor insertion tool, standard platform
Insertion Tools
V3 short ratchet insertion tool, standard platform
V3 long ratchet insertion tool, standard platform
Standard PlatformScrew type implant range
Length
Type
Implant cover screw and healing caps
Toll Free 1-(866) 797 1333
800-1000
600-800
450-650
Ø1.90 Ø3.90Ø2.40 Ø3 Ø3Ø2.40
200-400
200-400
V3-08390
V3-10390
V3-11390
V3-13390
V3-16390
Ø3.90mm
Ø3.90mm
Ø 3.90mm
Ø 3.90mm
Ø 3.90mm
Ø 3.90mm
Ø 3.90mm
Ø2.90 Ø 3.30
Ø 3.90
Ø3.15
Ø 3.80
Catalog No. Dimensions
length 8mm
length 10mm
length 13mm
length 16mm
length 11.50mm
Titanium Alloy Ti 6Al 4V ELISand-Blasted and Acid-Etched
Standard Platform
TorqueMax.60N·cm
Drilling Speed (RPM)
Diameter
Implant Procedure
The drilling sequence is illustrated using 11.50mm implants.
Procedure recommended by MIS cannot replace the judgment and professional experience of the surgeon.
Final drill For bone type 1&2
Final drill For bone type 3&4
Toll Free 1-(866) 797 1333
V3-08430
V3-10430
V3-11430
V3-13430
Ø 4.30mm
Ø 4.30mm
Ø 4.30mm
Ø 4.30mm
350-550
800-1000
600-800
450-650
Ø1.90 Ø4.30Ø2.40 Ø3 Ø3.50 Ø3.50Ø2.40
200-400
200-400
Ø4.30mm
12.
V3-16430 Ø 4.30mmØ3.40 Ø 3.70
Ø 4.30
Ø3.15
Ø 4.20
Ø4.30mm
Catalog No. Dimensions
length 8mm
length 10mm
length 13mm
length 11.50mm
Titanium Alloy Ti 6Al 4V ELISand-Blasted and Acid-Etched
Standard Platform
TorqueMax.60N·cm
Drilling Speed (RPM)
Diameter
Implant Procedure
The drilling sequence is illustrated using 11.50mm implants.
Procedure recommended by MIS cannot replace the judgment and professional experience of the surgeon.
Final drill For bone type 1&2
Final drill For bone type 3&4
length 16mm
Toll Free 1-(866) 797 1333
V3-08500
V3-10500
V3-11500
V3-13500
Ø5mm
Ø 5mm
Ø 5mm
Ø 5mm
Ø 5mm
350-550
800-1000
600-800
450-650
Ø1.90 Ø5Ø2.40 Ø3 Ø3.50 Ø4 Ø4Ø2.40
200-400
200-400
Ø5mm
300-500
Ø3.90 Ø 4.50
Ø 5
V3-16500 Ø 5mm
Ø 4.90
Ø3.15
length 8mm
length 10mm
length 13mm
length 11.50mm
Titanium Alloy Ti 6Al 4V ELISand-Blasted and Acid-Etched
Standard Platform
length 16mm
Catalog No. Dimensions
TorqueMax.60N·cm
Drilling Speed (RPM)
Diameter
Implant Procedure
Final drill For bone type 1&2
Final drill For bone type 3&4
The drilling sequence is illustrated using 11.50mm implants.
Procedure recommended by MIS cannot replace the judgment and professional experience of the surgeon.
Toll Free 1-(866) 797 1333
14.
Designed for Additional Room for Bone Growth.
The unique triangular-shape of the V3 implant’s coronal portion was designed to allow additional space for bone growth and created to support highly stable surrounding soft tissues and result in more esthetic restorations. This triangular design was created to provide solid anchorage at three points in the crestal area while forming gaps between the remaining sides of the implant neck and the osteotomy, which may result in a compression-free zone, where a stable blood clot may more easily be achieved. The ingenious combination of compression-free gaps with a firm anchorage may encourage the establishment of a stable blood clot; the first step towards a successful osseointegration process: Hemostasis Phase > Proliferative Phase > Remodeling Phase.
Toll Free 1-(866) 797 1333
MK-T051
Conical Connection Surgical Kit.
The innovative Conical Connection Surgical Kit, is designed for simple and safe implant placement procedures. The kit presents a novel ergonomic design that follows the surgical drilling sequence. In addition, the kit includes a set of length-based pilot drills and color-coded visual cues of both implant diameter and restorative platforms and is suitable for both C1 and V3 implants.
MT-SMD10
MT-PDM24
MT-PD440
MK-T051
CT-BTC24
CT-P2416
CT-BTC30
CT-P2413
CT-BTC35CT-P2411
CT-BTC40
CT-P2410
CT-P2408
CT-TDC40
CT-TDC35
3
1 4
5
6
7
8
CT-TDC30
2 10
11
12
9 13
14
15
16
17
18
3
1
2
4
5
6
7
8
9
9
9
10 11
13 14
16 17 18
39 40
44
45
MT-GDN33
MT-CSN33
MT-GDN50
16.
MARKING DRILLS PILOT DRILLS BODY TRY-INS STEP DRILLS
Step drill, external irrigation, Ø3.5/3mmPilot drill with built-in stopper for 10mm length implants, Ø2.4/2mm
Position drill mill, Ø2.4mm
Position drill, Ø4mm
Spade marking drill Pilot drill with built-in stopper for 8mm length implants, Ø2.4/2mm
Pilot drill with built-in stopper for 11.5mm length implants, Ø2.4/2mm
Pilot drill with built-in stopper for 13mm length implants, Ø2.4/2mm
Pilot drill for 16mm length implants, Ø2.4/2mm
Step drill, external irrigation, Ø3/2.4mm
Step drill, external irrigation, Ø4/3.5mm
Body try-in, Ø3mm
Body try-in, Ø3.5mm
Body try-in, Ø4mm
Body try-in, Ø2.4mm
Conical Connection
Surgical Kit.
Countersink for standard platform implant system
Countersink for narrow platform implant system
Countersink for wide platform implant system
Toll Free 1-(866) 797 1333
41
MT-DE001
39
MT-RE160
40
MT-RE172
MT-RDL30
42
MT-RDS30
43
45
MT-BTI20
44
25
CT-SSM30
19
CT-NLM30
23
CT-SLM30
24
CT-SLR30
26
CT-SSR30
20
CT-NLR30
22
CT-NSR30
21
CT-NSM30
CT-NSR10
28
29
30
CT-NLR10
34
CT-SSR10
27
CT-NLI10
CT-NSI10
33
CT-SSI10
CT-WSI10
3731
CT-SLI10
35
CT-WLI10
CT-WSR10
3832
CT-SLR10
36
CT-WLR10
12
15
18
19 27
23 31
35
21 29
25 33
37
20 28
24 32
36
22 30
26 34
3841 42 43
MT-RT070
C1 INSERTION TOOLS
V3 INSERTION TOOLS
V3 short motor insertion tool, standard platform
V3 long motor insertion tool, narrow platform
V3 long motor insertion tool, standard platform
V3 long ratchet insertion tool, standard platform
V3 short ratchet insertion tool, standard platform
V3 long ratchet insertion tool, narrow platform
V3 short ratchet insertion tool, narrow platform
V3 short motor insertion tool, narrow platform
SURGICAL TOOLS
Drill extender
Int. connection abutment extractor, narrow platform
Int. connection abutment extractor
Long driver for 0.05 inch hex.
Short driver for 0.05 inch hex.
Implant site depth probe
Short ratchet insertion tool, conical connection, narrow platform
Long ratchet insertion tool, conical connection, narrow platform
Short ratchet insertion tool, conical connection, standard platform
Long insertion tool, conical connection, narrow platform
Short insertion tool, conical connection, narrow platform
Short insertion tool, conical connection, standard platform
Short insertion tool, conical connection, wide platform
Long insertion tool, conical connection, standard platform
Long insertion tool, conical connection, wide platform
Short ratchet insertion tool, conical connection, wide platform
Long ratchet insertion tool, conical connection, standard platform
Long ratchet insertion tool, conical connection, wide platform
Toll Free 1-(866) 797 1333
Surgical torque ratchet
CT-SSM30 CT-SLM30 CT-SSR30 CT-SLR30
18.
3mm
6mm
V3 s
hort
ratc
het i
nser
tion
tool
V3 lo
ng ra
tche
t ins
ertio
n to
ol
V3 s
hort
mot
or in
sert
ion
tool
V3 lo
ng m
otor
inse
rtio
n to
ol
The advanced insertion tool system allows secure implant placement without the use of a mount.
Insertion Tools.
Standard platform tools shown
Toll Free 1-(866) 797 1333
B
C
A
A
Areas A and B indicate the position of the flat surface of the insertion tool to be aligned with the flat surface of the implant C.
This allows the dentist to easily identify the flat side of the implant for desired placement.
Toll Free 1-(866) 797 1333
The insertion tool allows the delivery of a cover screw or a healing cap onto the implant after insertion.
20.
Each V3 implant comes with a sterile cover screw and single-use final drill, suitable for all drilling protocols.
The sterile inner tube is fitted with a special titanium sleeve that has an anti-rotation grip, to ensure easy engagement between the insertion tool and the implant.
Cov
er S
crew
Fina
l Dril
l
Inne
r Tub
e
Out
er T
ube
Impl
ant
Package Contents.
Toll Free 1-(866) 797 1333
NARROW
Easy pull tab
Implant identification markings
Logical storage
The convenient pull tab facilitates quick and easy opening during surgery.
Packages fit perfectly into clinic drawers for space-saving storage and easy identification.
Quick identification of implant size and length. Sticker on the box lid, specifies implant diameter, length and platform size
Providing a simple, immediate identification of implant type, length and diameter, the V3 package is well-designed for ease-of-use during surgical procedures.
A double packing system ensures sterilization and safety. Packages are designed for convenience during surgery and for use with surgical gloves.
Implant diameter & platform indicationThe outer tube is color-coded indicating the implant platform. The numeric indication specifies the implant diameter and length.
Prosthetic platform indicationProsthetic components are marked by specific colors, representing platform sizes.
Packaging.
Toll Free 1-(866) 797 1333
® All rights reserved. No part of this publication may be reproduced, transcribed, stored in an electronic retrieval system, translated into any language or computer language, or be transmitted in any form whatsoever, without the prior written consent of the publisher.
www.V3-implant.com
© MIS Implants Technologies Ltd. All rights reserved.
MC
-V3M
CU
S R
ev. 6
The MIS Quality System complies with the
following international quality standards: ISO
13485:2003 - Quality Management System
for Medical Devices, ISO 9001: 2008 – Quality
Management System and Medical Device
Directive 93/42/EEC. Please note that not all
products are registered or available in every
country or region.