MODEL:

SERVICE MANUAL

MC-300 CD

CD/CASSETTE/RADIO MIDI SYSTEM

SERVICE MANUAL

CAUTION: Before servicing the chassis, read the "Important Service safety Information"

section on page 2 of this manual.

PORTABLE MW/FM RADIO WITH CASSETTE RECORDER

MW/FM TUNER SECTION

ANTENNA SYSTEM

TUNING RANGE

INTERMEDIATE FREQUENCY

AUDIO SECTION

SPEAKER IMPEDANCE

GENERAL

POWER INPUT

AC POWER CONSUMPTION

MW: FERRITE BAR

FM: TELESCOPIC

MW: 525~1650KHz

FM: 88~108KHz

MW: 465KHz +/-5KHz

FM: 10.7MHz +/-0.1MHZ

8 ohms

AC 230V, 50Hz

14V DC 12V

IMPORTANT SERVICE SAFETY INFORMATION

DISASSEMBLY INSTRUCTIONS

ALIGNMENT PROCEDURES

LOCATION OF CONTROLS

WIRING DIAGRAM

BLOCK DIAGRAM

IC BLOCK DIAGRAM

PRINTED CIRCUIT BOARDS

SCHEMATIC DIAGRAMS

EXPLODED VIEW

EXPLODED PARTS LIST

REPLACEMENT PARTS LIST

SERVICE PUBLICATION

SPECIFICATIONS CONTENTS

2

3

4

5

6

7

8-10

11-16

17-18

19

20

21-27

MODEL

MC-300 CD

SAFETY PRECAUTIONSBefore returning a unit to the customer, always make a safety check ofthe entire unit, including, but not limited to the following items:

a. Be sure that no built-in protective devices are defective and/or have been defeated during servicing.

Protective shields are provided to protect both the technician andthe customer. Correctly replace all missing protective shieldsincluding any removed for servicing convenience.When reinstalling the chassis and/or other assemblies in thecabinet, be sure t put back in place all protective devices, including,but not limited to, nonmetallic control knobs, insulating fishpapers,adjustment and compartment covers/shields and isolation resistor/capacitor networks. Do not operate this unit or permit it to beoperated without all protective devices correctly installed andfunctioning.

Be sure that there are no cabinet openings through which an adult orchild might be able to insert their fingers and contact a hazardousvoltage. such openings include, but are not limited to, excessively widecabinet ventilation slots, and an improperly fitted and/or incorrectlysecured cabinet back cover.

Leakage Current Hot Check - With the unit completely reassembled,plug the AC line cord directly into a 120V AC outlet. (Do not use anisolation transformer during this test.) Use a leakage current tester or ametering system that complies with American National Standardsinstitute (ANSI) C101.1”Leakage current for Appliances” andUnderwriters laboratories (UL) 1410,(50.7). With the unit AC switch firstin the ON position and then in the OFF position, measure from a knownearth ground (metal water pipe, conduit, etc.), especially any exposedmetal parts that offer an electrical return path to the chassis. Anycurrent measured must not exceed 0.5 milliamp. Reverse the unit powercord plug in the outlet and repeat test. ANY MEASUREMENTS NOTWITHIN THE LIMITS SPECIFIED HERENIN INDICATE A POTENTIALSHOCK HAZARD THAT MUST BE ELIMINATED BEFORERETURNING THE UNIT TO THE CUSTOMER.

Insulation Resistance Test Cold CheckUnplug the power supply cord and connect a jumper wire between thetwo prongs of the plug.Turn on the power switch of the unit.Measure the resistance with an ohmmeter between the jumpered ACplug and each exposed metallic cabinet part on the unit, such asscrewheads, antenna, control shafts, handle brackets, etc. When theexposed metallic part has a return path to the chassis, the readingshould be between 1 and 5.2 megohms. When there is no return path tothe chassis, the reading must be “infinite”. If it is not within the limitsspecified, there is the possibility of a shock hazard, and the unit must berepaired and rechecked before it is returned to the customer.

PRODUCT SAFETY NOTICESome electrical and mechanical parts have special safety relatedcharacteristics which are often not evident from visual inspection, norcan the protection they give necessarily be obtained by replacing themwith components rated for higher voltage, wattage, etc. Parts thathave special safety characteristics are identified by a onschematic and parts list. Use of a substitute replacement that does nothave the same safety characterist ics as the recommendedreplacement part might create shock, fire, and/or other hazards.Product safety is under review continuously and new instructions areissued whenever appropriate.SERVICING PRECAUTIONSCAUTION”Before servicing the unit covered by this service manualand its supplements read and follow the SAFETY PRECAUTIONS onthis page. NOTE”If unforeseen circumstances create a conflitbetween the following servicing precautions and any of the safetyprecautions, always follow the safety precautions. Remember: SafetyFirst.General Servicing Precautions.a. Always unplug the unit’s AC power cord from the AC power source before:(1) removing or reinstalling any component, circuit board, module, or any other unit assembly.(2) disconnecting or reconnecting any unit electrical plug or other electrical connection.(3) connecting a test substitute in parallel with an electrolytic capacitor in the unit. Caution: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.b. Do not defeat any plug/socket B+ voltage interlocks with which the unit covered by this service manual might be equipped.c. Do not apply AC power to this unit and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.d. always connect a test unit instrument’s ground lead to the unit’s chassis ground before connecting the test instrument’s positive lead. Always remove the test instrument’s ground lead last.

LASER PRECAUTIONSWARNING!!

When servicing, (in case it is necessary to confirm Laser BeamEmission) be sure not to place your eyes any closer than 1 ft or30cm from the surface of the Objective Lens on the OpticvalPickup Block.

HANDLING THE LASER PICKUPLaser diodes are extremely susceptible to damage from staticelectricity. Even if a static discharge does not ruin the diode, it canshorten its life or cause it to work improperly. When replacing thepickup, use a conductive mat on the floor and desk and wear awrist band connected to ground through a 1M ohm resistor toprotect the laser diode from static damage. If the lens should getdusty, blow off the dust carefully from the object.There are no adjustable parts in the pickup assembly. If it isdefective, replace the whole pickup assembly.

CAUTION:USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OFPROCEDURES HEREIN MAY RESULT IN HAZARDOUSRADIATION EXPOSURE.

DANGER:IF INTERLOCK FAILS OR IS DEFEATED, THE LASER LIGHT ISABLE TO FUNCTION. THE LASER IS INVISIBLE, AVOID DIRECTEXPOSURE TO BEAM.

IMPORTANT SERVICE SAFETY INFORMATION

2

ANTENNATERMINAL

EXPOSEDMETALPART OM

OHMMETER

(READING SHOULDNOT BE ABOVE0.5mA)

LEAKAGECURRENTTESTER

EARTHGROUND

TEST ALLEXPOSED METAL

SURFACES

AC Leakage Test

DEVICEUNDERTEST

2-WIRE CORDALSO TEST WITHPLUG REVERSED(USING AC ADAPTERPLUG AS REQUIRED)

+

1.

(1)

(2)

b.

c.

d.

2.

3.

4.

1.

2.

3.

DISASSEMBLY INSTRUCTIONS

1) ROTATE THE UNIT TO EXPOSE THE BACK SIDE.

2) REMOVE THE 12 SCREWS AS SHOWN IN FIG.1.

FIG.1

3

ALIGNMENT PROCEDURES

AM I.F. ALIGNMENT1. Set the POWER BUTTON to POWER"ON".2. Set the FUNCTION SELECTOR SWITCH to RADIO & AM BAND.3. Connect a SWEEPSCOPE OUTPUT to AM antenna terminal.4. Connect a SWEEPSCOPE INPUT to pin16 or pin17 of IC001 through a 1uf capacitor and ground.STEP SET SIGNAL SET DIAL ADJUST ADJUST FOR

1 465KHz GANG OPEN T101(AM IF)CENTER

& MAXIMUM OUTPUT

AM R.F. ALIGNMENT1. Connect an RF generator to a standard radiating loop.2. Connect a SCOPE and VTVM across the speaker output.

STEP SET SIGNAL SET DIAL ADJUST ADJUST FOR

1 525KHz GANG CLOSED T001 (AM OSC COIL)

2 1650KHz GANG OPEN CT003 (AM OSC TRIM.) MAXIMUM

3 600KHz 600KHz (AM ANT COIL) OUTPUT

4 1400KHz 1400KHz CT004 (AM ANT TRIM.)

5 REPEAT STEPS 3 AND 4 TO OBTAIN BEST TRACKING.

FM I.F. ALIGNMENT1. Set the POWER SWITCH to POWER "ON".2. Set the FUNCTION SELECTOR to RADIO & FM BAND.3. Connect a SWEEPSCOPE OUTPUT to pin5 of IC001 through a 20pF capacitor and ground.4. Connect a SWEEPSCOPE INPUT to pin16 or pin17 of IC001 through a 1uf capacitor and ground.

STEP SET SIGNAL SET DIAL ADJUST ADJUST FOR

1 10.7MHz GANG OPEN T105 (FM IF T)WITH 10.7MHz AT

ZERO CROSSOVER2

3

FM R.F. ALIGNMENT1. Connect an RF generator to the FM antenna terminal and ground.2. Connect a SCOPE & VTVM across the speaker output.STEP SET SIGNAL SET DIAL ADJUST ADJUST FOR

1 87.5MHz GANG CLOSED L103 (FM OSC COIL)

2 108.5MHz GANG OPEN CT002 (FM OSC TRIM.) MAXIMUM

3 90MHz 90MHz L102 (FM RF COIL) OUTPUT

4 106MHz 106MHz CT001 (FM RF TRIM)

5 REPEAT STEPS 3 AND 4 TO OBTAIN MAXIMUM OUTPUT.

CASSETTE ALIGNMENT1. Set the FUNCTION SELECTOR SWITCH TO TAPE.2. Connect a Scope & VTVM across the speaker output.3. Insert the 8KHz tape in to scassette deck and push play BUTTON.4. ADJUST HEAD for speaker maximum output.

CD ALIGNMENTTracking Balance:1. Play TNO. 1 of YEDS-7 or TCD-782 test cd.2. Connect a Scope across the (TSO) & (Vref).3. Set scope to DC position and ADJ. trace position=0.4. Press FF adjust VR2 the waveform is to become symmetrical with respct to "0" point.Focus Balance:1. Play TNO. 1 of YEDS-7 or TNO.2 of TCD-782.2. Connect a scope across the (RFO) & (Vref).3. adjust VR1 to obtain that the 3T-Level of EYE-pattem is mark.

4

MOTOR SCREWDRIVER

SCREWDRIVER

ADJUSTINGSCREW

ADJUSTMENT LOCATIONS

5

CT

10

0T

10

0

CT

10

3

T1

03

T1

02

L1

01

T1

01

T1

05

L1

03

L1

02

T1

04

L1

00

TRANSFOMER

CN10A

CN

9

CN

13

48-M

S100030-0

0

CN

8A

CN10

BE

ST

CU

T

CA

SS

ET

TE

DE

CK

CD

DE

CK

MO

TO

R

MA

INP

CB

CD

PC

B

48-MS4100005-00

WIRING DIAGRAM

6

TA

2111

N

FM

/AM

IF

AM

'RF

FM

'RF

DE

CK

#T

N-2

1F

PR

E.A

MP

BA

33

08

PO

WE

RA

MP

TA

82

27

SA

SS

BO

OS

T

PO

WE

RS

UP

PLY

TA

PE

TU

NE

R

BLOCK DIAGRAM

CD

ME

CH

SA

MS

UN

G

CM

S-V

75V

G6(U

)

CD

TC

9457F

-010

TA

2092N

TA

2109F

LC

D

DIS

PLA

Y

7

TA2109F

13

14

SBAD

FEO

15k

15k

FEN

50k

36pF

20uA

10k

7.96k

10k

VRO

RFRP 20k50uA

21k 21k

12k

12k

10k

30k

10k

21k 29k

24k 24k

1.74k

15

16

17

7.67k

10k

30

k

20pF

TEO

TEN

2VRO

TEB

SEL

3 STATE

DET.

47K SW1 LDC

10

pF

12

11

10

9

8

7

6

5

4

3

1k LDO

MD1

TN1

TP1

FP1

65

uA

SW2

SW3680

13k 2.12k

180k

20pF

180k

20pF

180k

40pF

20k

20k

I - I

I - I

60k

60k

20k

20k

FN1

Vcc

40

pF

18

0k

2

1

12k

RFGC

AGC1 23.5K

re-130

RFO

GND

RFN

1.53K

3.3

k

3.3

k

RFGO

RFIS

PEAK

BOTTOM

20k 20

k18

19

20

21

22

23

24

IC BLOCK DIAGRAM

8

1

2

3

4

5

6

7

8

9

10

11

12 13

14

15

16

17

18

19

20

21

22

23

24

-

+

-

+

+

-

+

-

PW GND

OUT(-)4

PVCC4

OUT(+)4

V IN4

SVCC4

SGND

V IN3

OUT(+)3

PVCC3

OUT(-)3

PW GND

PW GND

OUT(-)1

CC4PV

OUT(+)1

V IN1

V RI

V CI

VIN2

OUT(+)2

PVCC2

OUT(-)2

PW GND

TA2092AN/N

1 2 3 4 5 6 7 8 9

N

F

1

ALC

ch1

+

_

ch2

+

_

I

N

P

U

T

1

O

U

T

P

U

T

1

G

N

D

A

L

C

V

c

c

O

U

T

P

U

T

2

I

N

P

U

T

2

N

F

2

BA3308

MUTE

24 23 22 21 20 19

3

18

61

13

4

1416

2 5

1517

7

+ -

DET OUT MPX INAFC

FM

AM

AM OSC

VCOSTOP

LPF1LPF2

+

- -

+

AM

ANTENN

AM RF

IN

FM

OUT

RF VCC FM OSC

FM OSC

AM OSC

AM

M I X

FM

M I

FM SOFYMUTE

BPF

FM

ANTENN

FM RF RF

+

-

8 9 10 11 12AM

LOW CUTMIX OUT AGC

+

-

AGC

VCC

AMIF FMIF

A M

O E T

F M

O E T

LEVEL

DET

AF

BUFF

F M

MUTE

AFDECODE

VCO

DIVIDE

ST/MO

FM/AM

TUN

LED

ST

LED

AM IF FM IF GND TUN LED ST LED QUAD

FM

AF

+

-1 12

SW1

VCC2

VCC1

+

-

+ -2

OUT1

3

B.S.1

+

-

30k

ch-1+

-

6

IN1+-IN-1

5

NF1

45+

-

BIAS CIRCUIT

THERMAL SHUT DOWN

PROTECTION CIRCUIT

RIPPLE

9 FIN

PW-

GND

ch-2+

-

7

IN2+IN-1

8

NF2

45+

-

+ -12

OUT2

11

B.S.2

+

-

30k

4Pre-GND

OUT-2

OUT-1

+

-

-

TA2111N

TA8227P

9

PWMD / A

Clock

gene.+ -

Data

slicer

VREF

PLL

TMAX

VCO

+ -

+ -

A / DVREF+

-

Synchronous

guarantee EFM

decorde

CD

X'

talOSC

LP

F

1b

itD

AC

Digital equlaizer

Automatic adjustment

circuit

ROM

RAM

SERVO

Cont r ol

CLV

servo

Sub code decorder

Audi o

outDigital out

16kSRAM

Correction circuit Ad

dre

ss

CDReset

X' t al

OSCMPX Micon interface

CLCK,DATA,SESY.

LRCK,BCK,MBOY,IPF

SBSYCPU

Cl oc

k

Port1 Res

et

OT19- 22

Ti mer

Data.Reg.(16bit)

ROM

(16 X 81925 STEP)

G-Reg. R/W Buf.

RAM

( 4X 512 word) ALU

I nt er r r up

t

Cont . .

SBSY

Serial

interface

Port4

Program

Counter

Instruction

DecoderF/F

Stack Reg.

(8Level)

Bias

LCD Driver/Out Put Port Port8

CLCK,DATA,SESY

LRCK,BCK,MBOY,IPF

Power on

Reset

Reset

BUZR

A/D Conv.

Port3

ZV

RE

F

RFI

RFI

TMAX

PDO

SLCO

LPFN

DOUT

LPFO

VCOF

2PVREF

PVREF

SBOK

SBSY

COFS(OT22)

SPDA(OT21)

SPCK(OT20)

/HSD(OT19)

HOLD

TEST4

TEST5

TEST3

TEST2

TEST1

TEST0

RST

MVDD

MVSS

CO

M1(O

T1)

CO

M2(O

T2)

CO

M3(O

T3)

CO

M4(O

T4)

S1

(OT

5)

S11

(CL

OC

K/O

T1

5)

S1

0(O

T1

4)

S2

(OT

6)

S1

2(D

AT

A/O

T1

6)

S1

3(S

FS

Y/O

T1

7)

P8

-0

(BC

K/S

15

)

S1

4(L

RC

K/O

T1

8)

P8

-1

(BC

K/S

16

)

P8

-2

(BC

K/S

17

)

P8

-3

(BC

K/S

18

)

DM

O

FM

O

TE

BC

RF

GC

VR

EF

ZV

RE

F

FO

O

TR

O

TE

I

FE

ZI

SB

AD

FE

I

RF

RP

RF

ZI

RF

CT

AV

DD

AV

SS

SE

L

XVSS

XI

XO

XVDD

DVSR

RO

DVRR

DVDD

LO

DVSL

VDD

MXI

MXO

VSS

P1-3(K3)

P1-0(K0)

INTR

P4- 3

( SCK/ SCL)

P4-2(SO/S11

/SDA)

P4-0(ADIN4

/BUZR)

P4-1(S12)

P3-3(ADIN3)

P3-2(ADIN2)

P3-0(ADIN1)

P3-0

VREF

TC9457F

10

acad

Text Box

18

REF NO. PART NO.Q300,301 11-8050C0002-00 TRANSISTOR 8050CQ205,206,207,208,601,602,603 11-9014C0001-00 TRANSISTOR 9014C>Q209 11-9015C0001-00 TRANSISTOR 9015CZD302 12-136103100-02 ZENER DIODE +-5% (HITACHI) 3.6V 1/2W>ZD303 12-156103100-00 ZENER DIODE +-5% 5.6V 1/2W>ZD301 12-191103100-00 ZENER DIODE +-5% 9.1V 1/2W>D300,301,302,303,304 15-0001N4001-00 RECTIFIER DIODE 1N4001D101,102,201,202,203,601,602,603, 15-0001N4148-00 SWITCHING DIODE 1N4148 (LEAD TYPE)D607,608,609IC300 16-KA7808000-12 IC (SAMSUNG) KA7808IC2 16-TA2111N00-01 IC.RADIO (TOSHIBA) TA2111NIC1 16-TA8227P00-04 IC (TOSHIBA) TA8227P>R633 21-211103000-00 RESISTOR CARBON FILM +-5% 1 OHM 1/6WR105 21-212103000-00 RESISTOR CARBON FILM +-5% 10 OHM 1/6W>R102 21-213563000-00 RESISTOR CARBON FILM +-5% 560 OHM 1/6WR254 21-214223000-00 RESISTOR CARBON FILM +-5% 2.2K OHM 1/6W>R109,111 21-214823000-00 RESISTOR CARBON FILM +-5% 8.2K OHM 1/6WR106,629 21-215223000-00 RESISTOR CARBON FILM +-5% 22K OHM 1/6WR609,610 21-215273000-00 RESISTOR CARBON FILM +-5% 27K OHM 1/6WR256 21-215563000-00 RESISTOR CARBON FILM +-5% 56K OHM 1/6WR220,221,252,253,257,260 21-216103000-00 RESISTOR CARBON FILM +-5% 100K OHM 1/6WR259 21-216473000-00 RESISTOR CARBON FILM +-5% 470K OHM 1/6WR601,602 21-221223000-00 RESISTOR CARBON FILM +-5% 2.2 OHM 1/4WR104,301 21-222103000-00 RESISTOR CARBON FILM +-5% 10 OHM 1/4WR112,603,604 21-222473000-00 RESISTOR CARBON FILM +-5% 47 OHM 1/4WR6119 21-222563000-00 RESISTOR CARBON FILM +-5% 56 OHM 1/4W>R307,306,617 21-223103000-00 RESISTOR CARBON FILM +-5% 100 OHM 1/4W>R302 21-223223000-00 RESISTOR CARBON FILM +-5% 220 OHM 1/4W>R304,107 21-223563000-00 RESISTOR CARBON FILM +-5% 560 OHM 1/4WR620,621 21-224103000-00 RESISTOR CARBON FILM +-5% 1K OHM 1/4W>R303 21-224123000-00 RESISTOR CARBON FILM +-5% 1.2K OHM 1/4W>R300 21-224223000-00 RESISTOR CARBON FILM +-5% 2.2K OHM 1/4W>R108,110 21-224273000-00 RESISTOR CARBON FILM +-5% 2.7K OHM 1/4W>R618,619 21-224823000-00 RESISTOR CARBON FILM +-5% 8.2K OHM 1/4WR500,567,640 21-225103000-00 RESISTOR CARBON FILM +-5% 10K OHM 1/4WR622,623,624,631 21-225223000-00 RESISTOR CARBON FILM +-5% 22K OHM 1/4WR568,569 21-225273000-00 RESISTOR CARBON FILM +-5% 27K OHM 1/4WR630 21-225473000-00 RESISTOR CARBON FILM +-5% 47K OHM 1/4WR611,612,613,614,615,616, 21-225563000-00 RESISTOR CARBON FILM +-5% 56K OHM 1/4WR804,805 21-226123000-00 RESISTOR CARBON FILM +-5% 120K OHM 1/4WC566,567 25-132710300-00 CERAMIC CAP DISC TYPE +-5% 270PF 50VC999 25-133310300-00 CERAMIC CAP DISC TYPE +-5% 330PF 50VC350,613,614 25-141040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.001UF 50VC122,124 25-144740300-00 CERAMIC CAP DISC TYPE +80%-20% 0.0047UF 50VC219 25-152040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.02UF 50VC105,108,131,310,312,315,604,630 25-161040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.1 UF 50VC300,301,302,303,304,307,115C113 25-213010300-00 CERAMIC CAP DISC TYPE (NPO) 3PF 50V +-5%C109 25-221810300-00 CERAMIC CAP DISC TYPE (NPO) 18PF 50V +-5%C998 25-222010300-00 CERAMIC CAP DISC TYPE (NPO) 20PF 50V +-5%C112 25-222510300-00 CERAMIC CAP DISC TYPE (NPO) 25PF 50V +-5%C100,101,102 25-223010300-00 CERAMIC CAP DISC TYPE (NPO) 30PF 50V +-5%C111 25-231510300-00 CERAMIC CAP DISC TYPE (NPO) 150PF 50V +-5%>C118,119 25-351010300-00 MYLAR CAP +-5% 0.01UF 50VC607,608 25-361510300-00 MYLAR CAP +-5% 0.15UF 50V>C116, 26-311030500-00 ELECT CAP (RADIAL) 0.1UF 50V +-20% (NORMAL SIZE)C117 26-312230500-00 ELECT CAP (RADIAL) 0.22UF 50V +-20% (NORMAL SIZE)C103 26-314730500-00 ELECT CAP (RADIAL) 0.47UF 50V +-20% (NORMAL SIZE)>C568,569,610,609,617,618 26-321030500-00 ELECT CAP (RADIAL) 1UF 50V +-20% (NORMAL SIZE)C120,121,123,125,C351 26-3210305A0-02 ELECT CAP (RADIAL) "Hi-Q" (LL) 1UF 50V +-20% I<0.01CVC114,218,222 26-322230500-00 ELECT CAP (RADIAL) 2.2UF 50V +-20% (NORMAL SIZE)C104,800,801,804,805 26-324730500-00 ELECT CAP (RADIAL) 4.7UF 50V +-20% (NORMAL SIZE)>C620,621,106,619,627 26-332230200-00 ELECT CAP (RADIAL) 22UF 16V +-20% (NORMAL SIZE)C308,622 26-334730300-00 ELECT CAP (RADIAL) 47UF 25V +-20% (NORMAL SIZE)C107,305,314,605,611,612,606 26-341030200-00 ELECT CAP (RADIAL) 100UF 16V +-20% (NORMAL SIZE)C309,318 26-342230200-00 ELECT CAP (RADIAL) 220UF 16V +-20% (NORMAL SIZE)C306,311 26-344730200-00 ELECT CAP (RADIAL) 470UF 16V +-20% (NORMAL SIZE)C601,602 26-351030200-00 ELECT CAP (RADIAL) 1000UF 16V +-20% (NORMAL SIZE)

DESCRIPTION

REPLACEMENT PARTS LIST

21

>C313, 26-352230300-00 ELECT CAP (RADIAL) 2200UF 25V +-20% (NORMAL SIZE)>C603 26-354730300-00 ELECT CAP (RADIAL) 4700UF 25V +-20% (NORMAL SIZE)

27-00T1264MM-07 PVC (TOMY) (443DF-1DF 44-Q-3) T126/4MM (FOR A/F 2 BAND)>CF102 31-210705134-01 CERAMIC FILTER (MURATA) SFE10.7MJA10-A (RED)(3PIN)CF101 31-246503000-01 CERAMIC FILTER (MURATA) SFU465Y> 32-211801100-00 FERRITE BAR SIZE:10x80mmL103 38-202510005-00 FM COIL 5 x 2.5T (0.8mm)L102 38-203510015-00 FM COIL 4.5 x 3.5T (0.7mm)L101 38-204510015-00 FM COIL 4.5 x 4.5T (0.7mm)

38-212020003-00 AM COIL M3 AD/10.5mm 120:20T L=70mm x4J46 38-310002000-30 AXIAL INDUCTORS (EC-36 TYPE) 100UH +-10% (Idc max:275 mA)T105 40-000106FP9-18 I.F.T. 10mm (KONI) 106FP (PINK)T102 40-504000102-08 AM OSC COIL 10mm (KONI) #504 (RED)(1-2:16T/2-3:80T)T101 40-505000100-08 AM IFT 10mm 10mm (KONI) #505 (BLK)(3-1:102T/6-4:7T)SW2 41-134340309-13 SLIDE SWITCH (LUP FUNG) SKT-43D03-M9SW3 41-136340109-17 SLIDE SWITCH (LUCKY FIRST) SKT-63D01-M9-NKCN4,5 43-9A2001041-00 WAFER 4 PINS P=2mm 180CCN8 43-9A2001051-00 WAFER 5 PINS P=2mm 180CCN13A 43-9A2001081-00 WAFER 8 PINS P=2mm 180CCN11 43-9A2501021-00 WAFER 2 PINS P=2.5mm 180CCN3 43-9A2501031-00 WAFER 3 PINS P=2.5mm 180CCN14 43-9A2501041-00 WAFER 4 PINS P=2.5mm 180CCN1 43-9A2501051-00 WAFER 5 PINS P=2.5mm 180C

44-102440110-0A BARE WIRE dia 0.5mm L=40mm>FOR MAIN PCB CN6 TO CD PCB CN21 44-512610256-00 6P SHEILD WIRE(#30/26) SINGLE HOUSING(2.0mm) L=100mm

46-220420100-10 GLASS FUSE 5x20mm (BUSSMANN) 2.A/250V(BSI/VDE/SEMKO/IMQ/UR)46-400D05200-00 FUSE HOLDER (PAK HOP) D-052

>J14,11,43 47-301050102-10 UL TUBE I.D. 1x0.5x10mmFOR AM COIL 47-301050202-10 UL TUBE I.D. 1x0.5x20mmFOR AM COIL 47-302050302-10 UL TUBE I.D. 2x0.5x30mmW/48-MS4100020-01 x1 48-MS41000 48-MS4100001-01 MAIN PCB 163x185.5mm #4100 *

56-07000K500-00 BAR HOLDER H=22mm AD:10mm #K5FOR AM COIL 58-09KOPEN00-00CABLE TIE 2.5MMx4" #CV-100L102,103 58-82PR00200-00 SPONGE 10x10x10mm (WHITE)FOR IC TA8227 61-480AE3380-00 HEAT SINK #AE338 (10+25+10)x30x1.0mmFOR 7808 61-48AE33910-00 HEAT SINK #AE339 (2) L/23xW/8.9xH/(14.1+8.8)mmFOR IC7808 66-220300831-00 MACHINE SCREW MS/BH 3x8FOR PVC 66-250260431-00 MACHINE SCREW MS/KH 2.6x4AC1,2,FM ANT 66-760200451-00 EYELET 2x4mmFOR IC7808 SCREW 67-230000200-00 NUT DIA 3mmFOR SWITCH 68-021804042-00 FIBER WASHER 1.8x4x0.4mm

01-410000004-00 LED DISPLAY BOARD ASS'Y (RED) #4100>Q1,2 11-9015C0001-00 TRANSISTOR 9015C>D20,201,22,LED-300,LED-ST 13-1SLB25VR0-20 LED (ROHM) (RED) #SLB-25VR3F (2x5mm)

13-4CD120002-12 LED DISPLAY RED (FUTURE TECH) #FTEC-N0528DWRR-15D 25x19mm>R2 21-224153000-00 RESISTOR CARBON FILM +-5% 1.5K OHM 1/4W>R1,3 21-224393000-00 RESISTOR CARBON FILM +-5% 3.9K OHM 1/4WC2 25-161040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.1 UF 50V>CN17A 43-9B2001081-00 WAFER 8 PINS P=2mm 90C

44-102440110-0A BARE WIRE dia 0.5mm L=40mm>CN14A TO CD PCB CN14 44-512816257-00 7P WIRE (#28 UL1007) SINGLE HOUSING(2mm) L=160mm>CN16 TO CD PCB CN13A 44-512818258-00 8P WIRE (#28 UL1007) SINGLE HOUSING(2mm) L=180mm>CN6 TO MAIN PCB CN4 44-512830254-00 4P WIRE (#28 UL1007) SINGLE HOUSING(2mm) L=300mmW/48-MS4100005-01 x1 48-MS4100004-01 LED DISPLAY PCB 27.5x88mm #4100 *

01-410000005-00 KEY BOARD ASS'Y #4100>D3,9,10,11,12,13, 15-0001N4148-00 SWITCHING DIODE 1N4148 (LEAD TYPE)C-HV 25-151040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.01 UF 50V>SW3-8 41-151100000-0V TACT SWITCH (COMAX) RS-014RB1 (H=5mm F=160+-30gf)FOR C-HV TO SOLDERING LUG 44-302605008-41 STRAND JUMPER WIRE UL1007 AWG26 4+42+4mm (GRAY)FOR C-HV TO MAIN PCB AC1 44-302630200-41 STRAND JUMPER WIRE UL1007 AWG26 4+292+4mm (BLACK)>CN6 TO MAIN PCB CN4 44-512810254-00 4P WIRE (#28 UL1007) SINGLE HOUSING(2mm) L=100mm>CN17 TO DISPLAY CN16 44-512817258-00 8P WIRE (#28 UL1007) SINGLE HOUSING(2mm) L=170mm

48-MS4100005-01 KEY PCB 106x23mm #410061-870003312-00 SOLDERING LUG #331201-410000008-00 SPK OUTPUT JACK BOARD ASS'Y #410043-434180200-37 SPEAKER TERMINAL (WELLLONG) PST-418-020

>SPK PCB CN2A TO MAIN CN14 44-522218254-00 4P WIRE (#22 UL1007) SINGLE HOUSING(2.5mm) L=180mm48-MS4100008-00 SPK OUTPUT PCB #410001-410000009-00 HEADPHONE BOARD ASS'Y #4100

R5,6 21-223123000-00 RESISTOR CARBON FILM +-5% 120 OHM 1/4W43-433802005-01 PHONE JACK W/SW (TAI CHUNG) TC38-020-05-01

>FOR HP JACK TO MAIN PCB 44-522638255-00 5P WIRE(#26 UL1007) W/SINGLE HOUSING(2.5mm) L=380mm48-MS4100009-01 HEADPHONE PCB 19x28mm #410001-410000019-00 VOLUME BOARD ASS'Y #4100

22

>R605,606 21-224333000-00 RESISTOR CARBON FILM +-5% 3.3K OHM 1/4W>R607,608 21-224683000-00 RESISTOR CARBON FILM +-5% 6.8K OHM 1/4WVOL1 22-155002166-13 ROTARY VOLUME (POLYSHINE) F-122KGP A50K L=25FCX12>C616,615 25-361010300-00 MYLAR CAP +-5% 0.1UF 50V>POWER-SW;BASS-SW 41-182203L01-0V PUSH SWITCH (COMAX) 7x7mm PS-2203-L NS>FOR VOL PCB CN5 TO MAIN PCB CN8 44-512818255-02 5P WIRE#28UL1007) W/ SINGLE HOUSING(2mm) L=180mm>FOR VOL PCB CN4 TO MAIN PCB CN11 44-522225252-02 2P WIRE (#22 UL1007) SINGLE HOUSING(2.5mm) L=250mm (B/R)W/48-MS4100023-00 x1 48-MS4100019-00 VOLUME PCB 48x80mm #4100 *

01-410000020-00 RECORDER BOARD ASS'Y #4100>Q902,903,900 11-9014C0001-00 TRANSISTOR 9014C>Q901 11-9015C0001-00 TRANSISTOR 9015CD900 15-0001N4148-00 SWITCHING DIODE 1N4148 (LEAD TYPE)>IC3 16-BA3308000-02 IC.PRE.AMP (ROHM) BA3308R390 21-221223000-00 RESISTOR CARBON FILM +-5% 2.2 OHM 1/4W>R911,906, 21-222333000-00 RESISTOR CARBON FILM +-5% 33 OHM 1/4WR924 21-222473000-00 RESISTOR CARBON FILM +-5% 47 OHM 1/4W>R880, 21-223103000-00 RESISTOR CARBON FILM +-5% 100 OHM 1/4WR914 21-223563000-00 RESISTOR CARBON FILM +-5% 560 OHM 1/4W>R908,912,905,910 21-224563000-00 RESISTOR CARBON FILM +-5% 5.6K OHM 1/4WR902,942 21-224823000-00 RESISTOR CARBON FILM +-5% 8.2K OHM 1/4W>R920,919,918,905,914,917 21-225103000-00 RESISTOR CARBON FILM +-5% 10K OHM 1/4W>R903,901, 21-225153000-00 RESISTOR CARBON FILM +-5% 15K OHM 1/4W>R950,951 21-225183000-00 RESISTOR CARBON FILM +-5% 18K OHM 1/4W>R913, 21-225273000-00 RESISTOR CARBON FILM +-5% 27K OHM 1/4W>R909,907, 21-226103000-00 RESISTOR CARBON FILM +-5% 100K OHM 1/4W>R916 21-226223000-00 RESISTOR CARBON FILM +-5% 220K OHM 1/4W>R930 21-227103000-00 RESISTOR CARBON FILM +-5% 1M OHM 1/4W>C930,931 25-125610300-00 CERAMIC CAP DISC TYPE +-5% 56PF 50V>C882 25-161040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.1 UF 50VC915 25-341020300-00 MYLAR CAP +-10% 0.001UF 50V>C908,903,990 25-342220300-00 MYLAR CAP +-10% 0.0022UF 50V>C901,900, 25-342710300-00 MYLAR CAP +-5% 0.0027UF 50V>C914, 25-343320300-00 MYLAR CAP +-10% 0.0033UF 50VC909 25-344720300-00 MYLAR CAP +-10% 0.0047UF 50V>C912,905, 25-352210300-00 MYLAR CAP +-5% 0.022UF 50V>C910,911,916,942,906 26-324730500-00 ELECT CAP (RADIAL) 4.7UF 50V +-20% (NORMAL SIZE)C903,914 26-334730200-00 ELECT CAP (RADIAL) 47UF 16V +-20%>C820 26-341030100-00 ELECT CAP (RADIAL) 100UF 10V +-20% (NORMAL SIZE)>C881,991 26-342230100-00 ELECT CAP (RADIAL) 220UF 10V +-20% (NORMAL SIZE)> 40-621000100-08 I.F.T 10mm (KONI) #621 (BLACK)

41-191100100-03 PUSH SWITCH (LUP FUNG) RSA-102D01N-TS> 43-9A2501041-00 WAFER 4 PINS P=2.5mm 180C>CN10A 43-9B2001021-00 WAFER 2 PINS P=2mm 90CCN13 43-9B2001081-00 WAFER 8 PINS P=2mm 90CR922,923,D900 44-102404010-0A BARE WIRE dia 0.5mm L=40mm>COLOUR:R/W/GND DOUBLE SHEILD #28 44-512819258-00 8P SHEILD WIRE(#28/26) SINGLE HOUSING(2.mm) L=190mm *GND/R/W DOUBLE SHEILD #28R/BLUE WIRE #26 UL1007 =1

> 48-MS4100020-01 RECORDER PCB 55x78mm #4100>M+1,M+ 66-760200451-00 EYELET 2x4mm

01-410000023-00 BEATCUT SWITCH BOARD ASS'Y #410041-012210010-00 SLIDE SWITCH SS-22F10B-G8

CN10 45-052822252-00 2P SHEILD WIRE(#28 UL1533) SINGLE HOUSING(2mm) L=220mm48-MS4100023-00 BEAT CUT SWITCH PCB #410001-410000030-00 CD BOARD ASS'Y #4100

>Q101 11-2SA1317S2-03 TRANSISTOR (SANYO) 2SA1317SQ301,302 11-2SA134602-03 TRANSISTOR (SANYO) 2SA1346Q601 11-2SB764E02-03 TRANSISTOR (SANYO) 2SB764-EQ501,502 11-2SD1936T2-00 TRANSISTOR (SANYO) 2SD1936T>Q3 11-9014C0001-00 TRANSISTOR 9014C>23,22,305 15-0001N4148-00 SWITCHING DIODE 1N4148 (LEAD TYPE)>D301,302 15-GMB010004-11 DIODE (SANYO) GMB01-AT (TAPING)U101 16-LA9251M00-00 IC A.S.P (SANYO) LA9251M>U301 16-LC78602N0-09 IC (SANYO) LC78602NE>U201, 16-MM1469XH0-03IC (MITSUMI) MM1469XHR137 21-212223000-00 RESISTOR CARBON FILM +-5% 22 OHM 1/6W>R528, 21-213103000-00 RESISTOR CARBON FILM +-5% 100 OHM 1/6WR304 21-213223000-00 RESISTOR CARBON FILM +-5% 220 OHM 1/6WR106 21-213333000-00 RESISTOR CARBON FILM +-5% 330 OHM 1/6W>R520,521,522,523,524,525,526,527 21-213563000-00 RESISTOR CARBON FILM +-5% 560 OHM 1/6WR301 21-213683000-00 RESISTOR CARBON FILM +-5% 680 OHM 1/6WR124,126,134,138 21-214103000-00 RESISTOR CARBON FILM +-5% 1K OHM 1/6WR303 21-214123000-00 RESISTOR CARBON FILM +-5% 1.2K OHM 1/6W

23

R117 21-214153000-00 RESISTOR CARBON FILM +-5% 1.5K OHM 1/6WR103,513,515,516,518 21-214223000-00 RESISTOR CARBON FILM +-5% 2.2K OHM 1/6WR208 21-214273000-00 RESISTOR CARBON FILM +-5% 2.7K OHM 1/6W>R40,139,529 21-214473000-00 RESISTOR CARBON FILM +-5% 4.7K OHM 1/6WR125 21-214563000-00 RESISTOR CARBON FILM +-5% 5.6K OHM 1/6WR135,207,307,133,118 21-215103000-00 RESISTOR CARBON FILM +-5% 10K OHM 1/6WR201 21-215123000-00 RESISTOR CARBON FILM +-5% 12K OHM 1/6W>R108,113,131, 21-215153000-00 RESISTOR CARBON FILM +-5% 15K OHM 1/6W>R204,132,141, 21-215183000-00 RESISTOR CARBON FILM +-5% 18K OHM 1/6W>R111,R112,13,4,307,102 21-215223000-00 RESISTOR CARBON FILM +-5% 22K OHM 1/6WR107 21-215273000-00 RESISTOR CARBON FILM +-5% 27K OHM 1/6WR120 21-215333000-00 RESISTOR CARBON FILM +-5% 33K OHM 1/6WR109,121,123,302 21-215563000-00 RESISTOR CARBON FILM +-5% 56K OHM 1/6WR116 21-215683000-00 RESISTOR CARBON FILM +-5% 68K OHM 1/6W>R110,305,530,531 21-216103000-00 RESISTOR CARBON FILM +-5% 100K OHM 1/6WR101 21-216153000-00 RESISTOR CARBON FILM +-5% 150K OHM 1/6WR309,310 21-216223000-00 RESISTOR CARBON FILM +-5% 220K OHM 1/6WR140 21-216393000-00 RESISTOR CARBON FILM +-5% 390K OHM 1/6WR142 21-216683000-00 RESISTOR CARBON FILM +-5% 680K OHM 1/6WC124 25-121510300-00 CERAMIC CAP DISC TYPE +-5% 15PF 50VC117,318 25-131010300-00 CERAMIC CAP DISC TYPE +-5% 100PF 50VC105 25-133310300-00 CERAMIC CAP DISC TYPE +-5% 330PF 50VC313 25-136810300-00 CERAMIC CAP DISC TYPE +-5% 680PF 50V>C133,509,512 25-141040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.001UF 50V>C123 25-142240300-00 CERAMIC CAP DISC TYPE +80 -20% 2200PF 50V>C142, 25-143040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.003UF 50VC127,137,152,307 25-151040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.01 UF 50VC604 25-152040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.02UF 50VC104 25-153340300-00 CERAMIC CAP DISC TYPE +80%-20% 0.033UF 50VC301,302,140,601 25-161040300-00 CERAMIC CAP DISC TYPE +80%-20% 0.1 UF 50VC108,116,121 25-343310300-00 MYLAR CAP +-5% 0.0033UF 50VC130 25-346810300-00 MYLAR CAP +-5% 0.0068UF 50VC114 25-351510300-00 MYLAR CAP +-5% 0.015UF 50VC115 25-351810300-00 MYLAR CAP +-5% 0.018UF 50VC303,309,316,606 25-352210300-00 MYLAR CAP +-5% 0.022UF 50VC125 25-353310300-00 MYLAR CAP +-5% 0.033UF 50VC106,131 25-354710300-00 MYLAR CAP +-5% 0.047 UF 50VC101,109,113,144 25-361010300-00 MYLAR CAP +-5% 0.1UF 50VC107,3 26-311030500-00 ELECT CAP (RADIAL) 0.1UF 50V +-20% (NORMAL SIZE)C118 26-312230500-00 ELECT CAP (RADIAL) 0.22UF 50V +-20% (NORMAL SIZE)C132 26-313330500-00 ELECT CAP (RADIAL) 0.33UF 50V +-20% (NORMAL SIZE)C119 26-314730500-00 ELECT CAP (RADIAL) 0.47UF 50V +-20% (NORMAL SIZE)>C143,204, 26-322230500-00 ELECT CAP (RADIAL) 2.2UF 50V +-20% (NORMAL SIZE)C507,510 26-323330500-00 ELECT CAP (RADIAL) 3.3UF 50V +-20% (NORMAL SIZE)C126 26-331030500-00 ELECT CAP (RADIAL) 10UF 50V +-20% (NORMAL SIZE)C501 26-332230200-00 ELECT CAP (RADIAL) 22UF 16V +-20% (NORMAL SIZE)C134 26-334730300-00 ELECT CAP (RADIAL) 47UF 25V +-20% (NORMAL SIZE)C120,128,129,139,304,308,605 26-341030100-00 ELECT CAP (RADIAL) 100UF 10V +-20% (NORMAL SIZE)C135,138 26-342230100-00 ELECT CAP (RADIAL) 220UF 10V +-20% (NORMAL SIZE)>C202,602,305 26-344730100-00 ELECT CAP (RADIAL) 470UF 10V +-20% (NORMAL SIZE)>C603 26-351030100-00 ELECT CAP (RADIAL) 1000UF 10V +-20% (NORMAL SIZE)

31-316935001-01 CERAMIC RESONATOR 3P (MURATA) 16.934MHz (CSTLS16.M9X55-B0)CN2 43-9A1002151-00 WAFER (F.F.C) (LEADER WISE) 15P P=1.0mm 180CCN22 43-9A2001021-00 WAFER 2 PINS P=2mm 180C>CN6A,CN-M0T 43-9A2001061-00 WAFER 6 PINS P=2mm 180C>CN14, 43-9B2001071-00 WAFER 7 PINS P=2mm 90C>CN13A 43-9B2001081-00 WAFER 8 PINS P=2mm 90C

44-102440110-0A BARE WIRE dia 0.5mm L=40mm>FOR C501"+" TO MAIN PCB D201"+" 44-302615202-41 STRAND JUMPER WIRE UL1007 AWG26 4+142+4mm (RED)FOR C109 47-301050102-10 UL TUBE I.D. 1x0.5x10mm>. 48-MS4100030-01 CD PCB 111x120mm #4100> 58-090835000-00 CABLE TIE 5" (CHAIN) #08350

02-410000011-00 SPEAKER BOX ASS'Y "SCHNEIDER" #4100 (SIL.+CLOTH:BLUE)(76608)19-810530108-06 SPEAKER (C&T #CSYS072B1) 4"3W 8 OHM19-821050108-06 TWEETER (C&T #CSYS075B1) 3" 8 OHM 5-7W M/32mm26-622230500-00 NP ELECT CAP (RADIAL) 2.2UF 50V +-20% (NORMAL SIZE)

>FOR SPEAKER "+" 44-302606002-41 STRAND JUMPER WIRE UL1007 AWG26 4+52+4mm (RED)>FOR SPEAKER "-" 44-302607000-41 STRAND JUMPER WIRE UL1007 AWG26 4+62+4mm (BLACK)

45-183030024-A2 SPEAKER CORD UL2468 AWG-24 10+2980+10mm RED/BLACK#4100 (SIL.) 56-0441001A1-20 FRONT CAB-SPK BOX (HIPS)#4100 (SIL.) 56-0541001A1-20 REAR CAB-SPK BOX (HIPS)#4100 (CHROME) 56-2241001G1-10 TWEETER COVER(1) (ABS)#4100 (CHROME) 56-2241002G1-10 TWEETER COVER(2) (ABS)#1500 (BY BUYER) 56-5815000A9-11 LOGO BADGE (ABS) "S"

24

56-694100560-10 SPK PANEL PLATE(L) (ABS) #4100 (BLUE)56-694100660-10 SPK PANEL PLATE(R) (ABS) #4100 (BLUE)56-6941007A1-10 SHEET PLATE (1)-SPK BOX (ABS) #4100 (SIL.)56-80F168000-BA SPEAKER PANEL STUD (ABS) BLK #SG-F1680 (D/11.2xL/10.5mm)56-864100080-20 SPEAKER NET (HIPS) #4100 (GREY)57-080033910-07 PVC PLATE (BLACK) #AE339 (20x20x0.3mm)58-261030010-00 RUBBER FOOT (HARD) DIA 10mm; T=3.0mm(TRANSPARENT)58-65F168000-22 SILVER CAP DIA 22mm58-764100000-00 SPEAKER CLOTH (BLUE ST-003-33) #MS-4100 160x220mm

>FOR SPEAKER 61-900006040-00 SPEAKER CLIP #604>FOR FRONT CAB 61-9141000A1-00 SPEAKER GRILL (SMALL) #4100 (SILVER)>FOR SPEAKER 66-421301031-00 SELF-TAPPING SCREW TA/BH 3x10FOR FRONT CAB TO REAR CAB 66-421301831-00 SELF-TAPPING SCREW TA/BH 3x18FOR SPK WIRE 66-422300621-00 SELF-TAPPING SCREW TB/BH 3x6>FOR FIT PLATE TO FRONT CAB 66-481301031-00 SELF-TAPPING SCREW TA/WH 3x10FOR SPK WIRE 68-023214102-00 FIBRE WASHER 3.2x14x1mmWARNING 76-520308003-01 POLYBAG 02PEHD 3"x8"x0.03mm W/REC.& WARNING(E) *PLASTIC BAGS ARE NOT A TOY......AFOR SPK. BOXWARNING 76-521418003-00 POLYBAG 02PEHD 14.5"x18.5"x.03 W/WARN(E),REC.MARK & 6 HOLEPLASTIC BAGS CAN BE.......BABIES>FOR SPK BOX

77-314100101-00 RATING LABEL-SPK BOX "SCHNEIDER ML8LS"(76608)02-410000115-00 CASING ASS'Y 230V VDE CORD #410018-248541000-12 TRANSFORMER EI-48 (TENPAO) TG44094F2 230V 12V/1A 125C

TO MOTOR 26-342230200-00 ELECT CAP (RADIAL) 220UF 16V +-20% (NORMAL SIZE)>FOR HP JACK 5P WIRE 32-414051000-00 FERRITE CORE 14x8x5mm>FOR TRANS. 32-425131000-00 FERRITE CORE 25x15x13mm

32-516300502-03 MAGNET (DAWA) 16x30x5mm (380-400mt 6S)>FOR CD 41-061100000-QL LEAF SWITCH (WELTRONICS) MIC-MSW-2526GMVE

43-7400000U2-00 NUT WIRE CONNECTOR #U2 A/17.2mm B/10mm C/7.6mm>FOR SW. TO REC.PCB M+;FOR REC.PC 44-302608002-41 STRAND JUMPER WIRE UL1007 AWG26 4+72+4mm (RED)

44-302619300-41 JUMPER WIRE AWG-26 (UL1007) 4+1896mm (BLACK)FOR LEAF SWITCH TO CD PCB 44-512818252-04 2P WIRE(#28UL1571) W/SINGLE HOUSING(2mm) L=180mm>FOR CD DECK MOTOR TO DRIVF AMP C 44-513025256-00 6P WIRE (#30 UL1007) BOTH HOUSING(2.0mm) L=250mm>BLACK=250mm; RED/ORANGE=300mm 44-522630253-00 3P WIRE(UL1007#26) W/SINGLE HOUSING(2.5) L=250/300mm *>FOR MAIN PCB CN3 TO MOTOR AND SWFOR CD PCB TO CD DECK 44-8E0008065-00 15P FLEX FLAT CABLE 1mm S4+4 (0.035x0.7mm) L=80mm (D.SAME)>FOR CASS DECK 45-073020254-00 4P 3 CORE SHIELD WIRE(#30) SINGLE HOUSING(2.5) L=200mmPLUG :AP-21 (SUN FAIR) 45-112030118-02 AC CORD VDE APP.2M (BLK) (S.F) AP-21+H03VVH2-F/2Cx0.75mm2*FOR LED x5 47-301050102-10 UL TUBE I.D. 1x0.5x10mmFOR AC CORD 50-2000004K4-00 AC CORD BUSHING #4K4FOR REAR CAB. 57-080033600-07 COVER PLATE (PVC BLACK) #AE-336 (26.4x26.4x0.3mm)FOR 110/220V HOLE 57-0815310B1-07 PVC PLATE(BLK) 15.6x31.6x0.3mmFOR REAR CAB 57-0823230B1-07 PVC PLATE(BLK) 23.6x23.6x0.3mm>FOR REAR CAB 57-082613000-07 PVC PLATE (BLACK) 26.5x13.8mm

57-084100100-07 CASS KEY FUNCTION PLATE #4100 "REC/PLAY/....../EJECT.57-084100200-07 PVC PLATE(BLK) "FM ANT" #4100 31.6x15.6x0.3mm58-09KOPEN00-00CABLE TIE 2.5MMx4" #CV-10058-140033801-00 DIAL CORD DIA 0.4x750mm

FOR CD PCB TO TOP CAB 58-260274700-00 HARD RUBBER 10x15x7mm (W/TAPE 10x15mm)58-261030010-00 RUBBER FOOT (HARD) DIA 10mm; T=3.0mm(TRANSPARENT)58-4200B0800-00 MIC CUSHION #B08 dia 8.5x13x9mm (BLACK)58-61AC21000-00 SHOCK ABSORBER (RED) (SOFT TYPE 30C AC210)58-61AC22000-00 SHOCK ABSORBER (GREEN) (HARD TYPE 40C AC220)

FOR CD DECK BKT.x6 58-634100010-00 FIBRE PLATE #4100>KEY BRACKET x1 ; KEY KNOB ADAPTO 61-110033010-00 CASS. KNOB BRACKET ASS'Y 6 KEY (W/SCREW x2;SHAFT x1& *

61-11SCD6600-00 REC PCB BRACKET (1.0 THK) #SCD-66 (53.0x21.0x1.0mm)61-220033900-00 MOUNTING CLIP #AE339 (KING TALENT)61-25SCD6600-00 CONTACT PLATE (THK 1.2mm) #SCD-66 (11x11x8mm)61-76SCD6600-00 RECORDING PLATE #SCD-66

FOR MIC 61-900006040-00 SPEAKER CLIP #60461-944100010-00 LOCK SPRING #410061-950026600-09 SPRING DIAL dia 4x8x0.5mm

FOR CD DOOR 61-970003392-00 CD DOOR SPRING #AE-33961-97SCD6610-00 CASS DOOR SPRING (DIA 0.8) #SCD-66

FOR DIAL DRUM x1 66-220260531-00 MACHINE SCREW MS/BH 2.6x5FOR REC.PCB TO BKTx1 66-230300631-00 MACHINE SCREW MS/PH 3x6PCB BKT TO MAIN PCBx4FOR CD BKT.TO FRONT 66-250301231-00 MACHINE SCREW MS/KH 3x12

66-421260631-00 SELF-TAPPING SCREW TA/BH 2.6x6FRO VOLUME PCBx4 66-421261031-00 SELF-TAPPING SCREW TA/BH 2.6x10FOR LEAF SWITCH 66-421261231-00 SELF-TAPPING SCREW TA/BH 2.6x12FOR CASS DECK x4 66-421301031-00 SELF-TAPPING SCREW TA/BH 3x10

25

CD GEAR x2MIC x1CD HOLDER x3CD PCB x2FOR FRONT CAB. TO REAR x6 66-421302031-00 SELF-TAPPING SCREW TA/BH 3x20FOR TRANS. x2FOR GEAR TO FRONT CAB 66-422300831-00 SELF-TAPPING SCREW TB/BH 3x8FOR CD KEY PCB 66-431261031-00 SELF-TAPPING SCREW TA/PH 2.6x10FOR REAR CAB TO SPK JACK x2 66-431301011-00 SELF-TAPPING SCREW TA/PH 3x10 (BLACK)FOR REC. PCB x1 66-431301031-00 SELF-TAPPING SCREW TA/PH 3x10DISPLAY PCB x3DIAL BKT x7CD PCB x2FOR FIT PLATE TO FRONT CAB. x4 66-481301031-00 SELF-TAPPING SCREW TA/WH 3x10FOR RECx1 66-520200331-00 TAP TITE SCREW TT/BH 2x3FOR LASER COVER x2 66-520200610-00 TAP TITE SCREW TT/BH 2x6 (BLACK)FOR BKT TO DECK 66-530200331-00 TAP TITE SCREW TT/PH 2x3FOR CD DECK x4 66-922260821-00 SCREW TWP/BO 2.6x8.0MCFOR TRANS. x2 68-013216107-00 METAL WASHER 3.2x16x1.0mmFOR CASS DOOR 68-024008042-00 FIBRE WASHER 4x8x0.4mm

68-136000001-00 RING "E" TYPE 0.5T (SCRET60UN----)ERASE HEAD :PH-K380-MS1-6A 71-06MS41010-03 F/CASS DECK (TANASHIN) #TK20FX-S870-001(10 CLOCK)*R/P HEAD :AP-4211S(S3)MOTOR:M9T12U24-1

71-70DA11N00-02 CD MECHANISM (SANYO) DA11N (13930420)77-401500000-01 THERMAL FUSE FITTED D125.C" R1 LABEL 32x9mm (PRINT RED)03-410000115-10 PACKING ASS'Y A/F 230V-GERMANY "SCHNEIDER ML8"

WARNING:(EMERSON FORMAT) 76-521016003-01 POLYBAG 02PEHD 10"x16"x0.03mm W/REC.WARN(E/F) & 4HOLES *Keep this bag....THIS IS NOT A TOFOR I/B>FOR UNIT 76-521721003-00 POLYBAG PE02HD 17"x21"x0.03mm W/WARN(E) & REC. MARK 8 HOLEWARNING:TO AVOID DANGERS OF SUFFO 76-524524003-00 POLYBAG 04PELD 4.5"x24"x0.03mm W/WARN & RECYCLE MARK (4 HOLE)AWAY FROM BABIES AND CHILDREN.DOCRIBS,BEDS,PRAMS OR PLAY PETHIS BAG IS NOT A TOY.FOR AC CORD

76-644100011-00 POLYFOAM TOP-1 #410076-644100012-00 POLYFOAM TOP-2 #410076-644100013-00 POLYFOAM TOP-3 #410076-644100014-00 POLYFOAM TOP-4 #410076-654100011-00 POLYFOAM BOTTOM-1 #410076-654100012-00 POLYFOAM BOTTOM-2 #410076-654100013-00 POLYFOAM BOTTOM-3 #410076-654100014-00 POLYFOAM BOTTOM-4 #4100

>556x252x315mm 77-014100000-00 GIFT BOX (4004423766105) "SCHNEIDER ML8"(76610)77-060000001-00 Q A PASSED LABEL77-070000001-00 Q C PASSED LABEL

FOR UNIT x1 77-093510000-00 SERIAL NO LABEL 35x10mmCARD x1GIFT x2FOR UNIT INNER 77-094035000-00 SERIAL NO LABEL 1 SETS (35x10mm x3PCS)

77-144100000-00 IDENTIFICATION CARD #4100 "SCHNEIDER ML8"(76610)77-1X0000032-00 CD TRAY CARD (E.) DIA:123mm77-204100001-00 INSTRUCTION MANUAL #4100 "ML8"

PRINT:BLACK WORDS 77-290000001-00 CAUTION LABEL (E/DE/FI/SW) 47x30mm GROUND:YELLOW *77-314100002-00 RATING LABEL-UNIT "SCHNEIDER ML8"(76609)77-48M660010-00 CLASS 1 LASER LABEL 25x45mm #M66 (4 LANGUAGE)

FOR UNIT 77-58M660020-00 AC INPUT LABEL 35x5mm #M66 "AC230V 50Hz"(BLK P:WHITE77-810000001-00 LASER BEAM LABEL (TRIGONAL) PRINT:YELLOW/BLACK06-410000115-00 PLASTIC ASS'Y A/F #4100 (SIL.877C)56-0241000A2-10 TOP CD BASE (ABS) #4100 (SIL.877C)56-0441000A2-20 FRONT CAB-UNIT (HIPS) #4100 (SIL.877C)56-0541000A2-20 REAR CAB-UNIT (HIPS) #4100 (SIL.877C)56-070CD2300-BA CD MAGNET HOLDER (ABS) #CD-23 (BLACK)56-074100180-10 CASS DOOR BKT (ABS) #410056-074100280-10 DIAL BKT (ABS) #410056-1341000A2-10 CASS DOOR (ABS) #4100 (SIL.877C)56-1441000A2-10 CD DOOR (ABS) #4100 (SIL.877C)56-1610600B0-10 MAGNET CAP TOP (ABS) (BLACK) #CT-106 (DIA42mm) (SANYO CD)

>W/"T" MARK (R2:THICK CHANGE) 56-1610601B0-12 MAGNET CAP BOTTOM(ABS)(BLACK) #CT-106 (DIA60mm)(SANYO CD) R256-220338C00-BA LASER COVER (ABS) #AE-338C (SANYO CD)56-244100180-10 DAMPER -CD DOOR (ABS) #410056-244100280-10 DAMPER HOLDER-CD DOOR (ABS) #410056-244100380-10 DAMPER -CASS DOOR (ABS) #4100

26

56-244100480-10 DAMPER HOLDER-CASS DOOR (ABS) #410056-250089000-BA DIAL DRUM (ABS) #SX-890 (BLACK)56-5441001A2-10 KNOB -BASS (ABS) #4100 (SIL.877C)56-5441002A2-10 KNOB -BAND (ABS) #4100 (SIL.877C)56-5441003A2-10 KNOB -TUNING (ABS) #4100 (SIL.877C)56-5441004A2-10 KNOB -POWER (ABS) #4100 (SIL.877C)56-5441005A2-10 KNOB -FUNCTION (ABS) #4100 (SIL.877C)56-5441006G1-10 KNOB -CD (ABS) #4100 (CHROME)56-5441007A2-10 KNOB -PROGRAM (ABS) #4100 (SIL.877C)56-5441008A2-10 KNOB -VOLUME (ABS) #4100 (SIL.877C)56-5441009A2-10 KNOB -CD DOOR OPEN (ABS) #4100 (SIL.877C)56-5541000A2-10 KNOB -CASSETTE 6KEY (ABS) #4100 (SIL.877C)56-574100100-60 LENS -DAIL (ACRYLIC) #410056-574100200-60 LENS -CD DOOR (ACRYLIC) #410056-574100300-60 LENS -CASSETTE(ACRYLIC) #410056-644100080-10 HOOK -CD DOOR OPEN (ABS) #410056-694100160-10 FIT PLATE"L"-FRONT CAB (ABS) #4100 (BLUE)56-694100260-10 FIT PLATE"R"-FRONT CAB (ABS) #4100 (BLUE)56-6941003G0-10 FIT PLATE(1) -FRONT CAB (ABS) #4100 (CHROME)56-754100080-10 POINTER (ABS) #4100 (GREY)56-760981100-AA PULLEY #981156-794100080-10 TUNING SHAFT (ABS) #4100 (GREY)07-410000100-00 INDIRECT MATERIAL #4100 (PCB)79-290306330-00 HIGH TEMPERATURE MASKING TAPE W=1/4" (S/N:A52)79-290312730-00 HIGH TEMPERATURE MASKING TAPE W=1/2" (S/N:A53)79-460101030-00 SOLDER WIRE 50% DIA 1.0mm (S/N:B7)79-480105020-00 SOLDER BAR 50% (S/N:B1)79-480206320-00 SOLDER BAR 63% (S/N:B2)79-510105030-00 HEATSINK GREASE (S/N:B22)79-620204830-00 WAX LOW TEMPERATURE #BAOYE (S/N:B11)79-680203530-00 GLUE (YELLOW) #BY-883A (S/N:B26)79-680901030-00 GLUE (YELLOW) #1603(UL) (S/N:B23)79-730201540-00 THINNER #680 (S/N:B50)79-730502040-00 SOLVENTS #880B (S/N:B48)79-730601540-00 FLUX (S/N:B45)

27