MATERIAL SAFETY DATA SHEET · Section 5. Health Hazard Data May be harmful if inhaled. May cause...

AMERICAN INTERNATIONAL INDUSTRIES2220 GASPAR AVENUELOS ANGELES, CA 90040CHEM-TEL: (800) 255-3924

PRODUCT NAME: IBD The Professional Gel Kit - 5 Second Gel Glue DATE: 9/16/2004ITEM: 55403 REV. NEW

CAS # %7085-85-0 85-99%

Boiling Point: 62oC (5mm Hg) Specific Gravity: 1.05Vapor Pressure: 0.13mm Hg @ 20oC (@ 20oC)(mm Hg and Temperature) Melting Point: N/AVapor Density: > 1 Evaporation Rate: < 1(Air = 1) (Butyl Acetate = 1)Solubility in Water: Polymerize Water Reactive: N/AAppearance: Colorless Gel pH: Not AvailableOdor: Irritating Freezing Point: < -20oC

Flash Point and Method Used: 83oC (C.O.C.)Auto-Ignition Temperature: 485oCFlammability Limits in Air % by Volume: LEL: Not Available

UEL: Not AvailableExtinguisher Media:Special Fire Fighting Procedures: Use water to keep fire-exposed containers cool.Unusual Fire and Explosion Hazards: Keep away from heat and flame.

Stability:Conditions to Avoid:Incompatibility (Materials to Avoid):

Water, alcohols, amines, bases, and direct UV.Hazardous Decomposition:

Oxides of carbon.Hazardous Polymerization:

May Occur

Use water spray, dry chemical, foam, or CO2.

Normally stable, but may become unstable at high temperatures or may react with water.

MATERIAL SAFETY DATA SHEET

Section 4. Reactivity Hazard Data

Section 3. Fire and Explosion Hazard Data

Will Not Occur

Section 2. Physical / Chemical Characteristics

Section 1. Material Identification and Information

Hazardous Ingredients:Component TOXICOLOGICAL DATA

Ethyl Cyanoacrylate ACGIH TLV/TWA:1mg/m3

Exposure to heat, flame, and incompatibles.

of 4




Emergency Overview:CAUTION! COMBUSTIBLEMay become unstable at high temperatures or may react with water.Bonds eyelids instantly. Causes eye irritation.Bonds skin instantly. Causes skin irritation.

HMIS Rating: Health: 2 (moderate)Flammability: 2 (moderate)Reactivity: 1 (slight)

Primary Routes of Entry: Inhalation Ingestion

Carcinogen Listed In: NTP OSHA

Health Hazards: Eye Contact: Bonds eyelids instantly. Causes eye irritation.Skin Contact: Bonds skin instantly. Causes skin irritation.Inhalation:

Ingestion: No hazards known to company.Signs and Symptoms of Exposure:

May cause eye irritation.Medical Conditions Generally Aggravated by Exposure:

No adverse effects are known.Emergency First Aid Procedures:

Eye Contact:

Skin Contact:

Inhalation:

Ingestion:

May be harmful if inhaled. Liquid or vapor may cause irritation of nose, throat, and lungs.

If eye irritation occurs, hold eyelid open and rinse thoroughly but gently with only water for 15 minutes and GET MEDICAL ATTENTION. Do not use any solvents to flush the eye and its surroundings. Liquid glue will sting temporarily. Solidified glue may irritate eye like a grain of sand and should be treated by a eye doctor.If skin bonding occurs, soak in acetone based nail polish remover or acetone and carefully peel or roll skin apart (do not pull).If inhaled, remove to fresh air. If not breathing, give artificial respiration, preferably mouth-to-mouth. Call a physician.

Eye Contact Skin Absorption

Not Listed IARC Monograph

Section 5. Health Hazard Data

May be harmful if inhaled. May cause irritation of nose, throat, and lungs.

If accidentally swallowed, dilute by drinking large quantities of water. Immediately contact poison control center or hospital emergency room for any other additional treatment directions.

of 4




Engineering Controls:

Personal Protection:Use goggles if contact is likely. Wear impervious gloves as required to prevent skin contact.

Hygienic Work Practices:Good Manufacturing Practices.

Steps to be Taken if Material is Spilled or Released:

Waste Disposal Methods:

Precautions to be taken in Handling and Storing:

Inhalation: Avoid breathing vapor. Use with adequate ventilation.Skin: Avoid contact with skin and clothing.Eyes: Avoid contact with eyes.

Other Precautions and/or Special Hazards:None

Recover free liquid. Absorb residue and dispose of according to local, state/provincial, and federal requirements. Empty container: May contain explosive vapors. DO NOT cut, puncture or weld on or nearby.

Handle in accordance with good industrial hygiene and safety practices. These practices include avoiding unnecessary exposure and removal of the material from eyes, skin, and clothing. Wash thoroughly after handling. Always use appropriate Personal Protective Equipment (PPE).

Keep away from amines. Store in cool, dry area away from sun and heat. Keep containers tightly closed. Exposure to small amounts of moisture, even moisture in air, causes polymerization and renders the product unusable. Keep away from heat, sparks, flame, and other ignition sources.

The following exposure control techniques may be used to effectively minimize employee exposure: local ventilation, enclosed system design, process isolation and remote control in combination with appropriate use of personal protective equipment and prudent work practices. These techniques may not necessarily address all issues pertaining to your operations. Therefore, it is recommended that you consult with experts of your choice to determine whether or not your programs are adequate. If airborne contaminants are generated when the material is heated or handled, sufficient ventilation in volume and air flow patterns should be provided to keep air contaminant concentration levels below acceptable criteria.

Eliminate all ignition sources. Soak up with absorbent material and remove to a chemical disposal area. Prevent entry into natural bodies of water.

Section 6. Control and Protective Measures

Section 7. Precautions for Safe Handling and Use / Leak Procedures

of 4




See Section 5 for Hazardous Identification information.LD50: more than 5,000mg/kg (oral rat); Ethyl Cyanoacrylate

Not determined.

U.S. Department of Transportation (DOT):

U.S. Federal Regulations:●OSHA Hazard Communication Standard 29 CFR 1910-1200:

●SARA Title III: Section 311/312:Fire Hazard.Immediate Health Hazard●SARA Title III: Section 313 and 40 CFR Part 372:

●TSCA Section 8(b) Inventory:All reportable chemical substances are listed on the TSCA Inventory.

The data provided in this section is for information only and may not be specific to your package size. You will need to apply the appropriate regulations to properly classify your shipment for transportation. Combustible. (Containers less than 110 gallons non-regulated)

Section 11. Regulatory Information

This material is a "heath hazard" and/or a "physical hazard" as determined when reviewed according to the requirements of the Occupational Safety and Health Administration 29 CFR Part 1910.1200 "Hazard Communication" Standard.

This product contains the following toxic chemical(s) subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986, and Subpart C-Supplier Notification Requirement of 40 CFR Part 372. None required per SARA TITLE III SECTION 313.

Section 8. Toxicological Information

Section 9. Ecological Information

Section 10. Transport Information

of 4


PRODUCT NAME: IBD The Professional Gel Kit 5 Second Ultra Fast Nail Glue DATE: 9/14/2004ITEM: 51102 REV. NEW

CAS # %7085-85-0 > 99%

Boiling Point: 62oC (5mm Hg) Specific Gravity: 1.05Vapor Pressure: 0.13 @ 20oC (@ 20oC)(mm Hg and Temperature) Melting Point: N/AVapor Density: > 1 Evaporation Rate: < 1(Air = 1) (Butyl Acetate = 1)Solubility in Water: Polymerize Water Reactive: N/AAppearance: Colorless Liquid Freezing Point: < -20oCOdor: Irritating pH: Not Available

Flash Point and Method Used: 83oC (C.O.C.)Auto-Ignition Temperature: 485oCFlammability Limits in Air % by Volume: LEL: Not Available

UEL: Not AvailableExtinguisher Media:

Special Fire Fighting Procedures: NoneUnusual Fire and Explosion Hazards: None

Stability:Conditions to Avoid:Incompatibility (Materials to Avoid):

Water, alcohols, amines, bases, and direct UV.Hazardous Decomposition:

Oxides of carbon.Hazardous Polymerization:

May Occur

ACGIH PEL/TWA:1mg/m3

Exposure to heat, flame, and incompatibilities.

Will Not Occur



Hazardous Ingredients:Component

Ethyl CyanoacrylateTOXICOLOGICAL DATA

In case of fire, use water spray, dry chemical, foam, or CO2. Use water to keep fire-exposed containers cool.

Normally stable, but may become unstable at high temperatures or may react with water.




Page 1 of 4






Health Hazards: Eye Contact: Bonds eyelids instantly. Causes irritation.Skin Contact: Bonds skin instantly. Causes irritation.Inhalation:

Ingestion: No hazards known.Emergency First Aid Procedures:

Eye Contact:

Skin Contact:

Inhalation:

Ingestion:

Engineering Controls:

Protective Gloves: Wear impervious gloves as required to prevent skin contact.Eye Protection: Other Protective Clothing and Equipment:

Always use appropriate Personal Protective Equipment (PPE).Hygienic Work Practices:

Good Manufacturing Practices.

If accidentally swallowed, dilute by drinking large quantities of water. Immediately contact poison control center or hospital emergency room for any other additional treatment directions.

If skin bonding occurs, soak in acetone based nail polish remover or acetone and carefully peel or roll skin apart (do not pull).If inhaled, remove to fresh air. If not breathing, give artificial respiration, preferably mouth-to-mouth. Call a physician.


Use goggles if contact is likely.

May be harmful if inhaled. Liquid or vapor may cause irritation of nose, throat, and lungs.

If eye contact occurs, hold eyelid open and rinse thoroughly but gently with only water for 15 minutes and GET MEDICAL ATTENTION. Do not use any solvents to flush the eye and its surroundings. Liquid glue will sting eye temporarily. Solidified glue may irritate eye like a grain of sand and should be treated by an eye doctor.

The following exposure control techniques may be used to effectively minimize employee exposure: local exhaust ventilation, enclosed system design, process isolation and remote control in combination with appropriate use of personal protective equipment and prudent work practices. These techniques may not necessarily address all issues pertaining to your operations. We, therefore, recommend that you consult with experts of your choice to determine whether or not your programs are adequate. If airborne contaminants are generated when the material is heated or handled, sufficient ventilation in volume and air flow patterns should be provided to keep air contaminant concentration levels below acceptable criteria.




Page 2 of 4







Inhalation: Avoid breathing vapor. Use with adequate ventilation.Skin: Avoid contact with bonding skin and clothing.Eyes: Avoid contact with eyes.


LD50: more than 5,000mg/kg (oral rat); Ethyl 2-Cyanoacrylate

U.S. Department of Transportation (DOT):

Section 8. Toxicological Information

Section 9. Transport Information

The data provided in this section is for information only and may not be specific to your package size. You will need to apply the appropriate regulations to properly classify your shipment for transportation. Combustible. (Containers less than 110 gallons non-regulated)

Recover free liquid. Absorb residue and dispose of according to local, state/provincial, and federal requirements. Empty container. May contain explosive vapors. DO NOT cut, puncture, or weld on or nearby.

Handle in accordance wit good industrial hygiene and safety practices. These practices include avoiding unnecessary exposure and removal of the material from eyes, skin, and clothing. Wash thoroughly after handling. Always use appropriate Personal Protective Equipment (PPE).

Keep away from amines. Store in cool, dry area away from sun and heat. Keep containers tightly closed. Exposure to small amounts of moisture, even moisture in air, causes polymerization and renders the product unstable. Keep away from heat, sparks, flame, and other ignition sources.

Eliminate all ignition sources. Soak up with absorbent material and remove to a chemical disposal area. Prevent entry into natural bodies of water.


Page 3 of 4




U.S. Federal Regulations:●OSHA Hazard Communication Standard 29CFR1910.1200:

●SARA Title III: Section 311/312:Fire hazardImmediate health hazard●SARA Title III Section 313 and 40 CFR Part 372:

●TSCA Section 8(b) Inventory:All reportable chemical substances are listed on the TSCA Inventory.

HMIS Rating: Health: 2 (moderate)Flammability: 2 (moderate)Reactivity: 1 (slight)

Section 11. Other Information

Section 10. Regulatory Information

This material is a "health hazard" and/or a "physical hazard" as determined when reviewed according to the requirements of the Occupational Safety and Health Administration 29 CFR Part 1910.1200 Hazard Communication Standard.

This product contains the following toxic chemical(s) subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986, and Subpart C-Supplier Notification Requirement of 40 CFR Part 372. None required per SARA TITLE III SECTION 313.

Page 4 of 4


PRODUCT NAME: IBD The Professional Gel Kit - Bonder DATE: 9/14/2004ITEM: 60805 REV. NEW

CAS # %27813-02-1 ~30%84170-74-1 ~5%

Boiling Point: Will polymerize before boiling. Specific Gravity: ~ 1.05Vapor Pressure: < 1mmHg @ 70oF / 21oC (H2O = 1)(mm Hg and Temperature) Melting Point: N/AVapor Density: Not Available Evaporation Rate: N/A(Air = 1) Water Reactive: NoSolubility in Water: Parially Appearance: Colorless Liquid Odor: Slightly Sweet Odor

Flash Point and Method Used: 228oF / 109oC (PMCC)Auto-Ignition Temperature: N/AFlammability Limits in Air % by Volume: LEL: N/A

UEL: N/AExtinguisher Media:Special Fire Fighting Procedures:

Unusual Fire and Explosion Hazards:

Stability: StableConditions to Avoid:

Water spray, carbon dioxide, and dry chemic

Unstable

Cool exposed containers with water spray. Use self-contained breathing apparatus in confied areas.Product may polymerize at high temperatures. Polymerize may produce sufficient heat to cause thermal decomposition and/or rupture of containers. Thermal decomposition can lead to the evolution of irritant vapors or gases and/or fires.

Heat, organic or inorganic free radical producing initiators, exposure to sunlight, unltraviolet light or ionizing radiation, trace metals, alkaline substances. Direct heat, chemical combination, sunlight, ultraviolet light or ionizing radiation. Do not exceed 60 oC for limited periods if warming is required.




Hydroxypropyl MethacrylateTOXICOLOGICAL DATA

Neopentylglycol Propocylate Diacrylate

None EstablishedNone Established




Page 1 of 3




Incompatibility (Materials to Avoid):Primary and secondary amines, acids, alkalies, free radical producing initiators.

Hazardous Decomposition:Carbon Dioxide, Carbon Monoxide

Hazardous Polymerization: May Occur



Health Hazards: Acute:

Chronic: May cause sensitization on repeated skin contact.Signs and Symptoms of Exposure:

Irritated skin and eyes. Reddening or swelling of affected area.Medical Conditions Generally Aggravated by Exposure:

None known.Emergency First Aid Procedures:

Eye Contact:

Skin Contact:

Inhalation: Remove to fresh air and consult physician.Ingestion: Do not induce vomiting. Immediately consult a physician.

Respiratory Protections (Specific Type):NIOSH / MSHA approved respirator in cases of high vapor concentration.

Protective Gloves: Impervious (butyl rubber, neoprene)Eye Protection: Ventilation to be Used:

Other (Specify)Other Protective Clothing and Equipment:

When handling larger quantities, apron and rubber boots.Hygienic Work Practices:

Flsuh with large amounts of water for at least 15 mintues holding lids apart. In case of irritation, consult a physician.Wash thoroughly with soap and water. Remove contaminated clothing and footwear. Get medical attention if irritation should develop.

Avoid contact with eyes, skin, and mucous membranes. Otherwise follow the standards of good industrial hygiene practice.


Chemical splash goggles.

Local Exhaust

May cause skin irritation on prolonged contact. Eye irritant. Ingestion may cause irritation to the mucous membranes of mouth, throat, and digestive tract.




Will Not Occur

Page 2 of 3







Other Precautions and/or Special Hazards:After expiration of storage time spontaneous polymerization may occur.

Dispose in an approved chemical waste landfill or incinerate in accordance with applicable Federal, State, and Local regulations.

Store below 85oF in well ventilated area away from direct sunlight, initiators, oxidizing and/or reducing agents. Do not fill containers completely.

Stop leaks. Clean up large spills with vacuum truck. Soak up small spills with absorbent material. Wear adequate personal protective clothing and equipment.


Page 3 of 3


PRODUCT NAME: IBD Professional Gel Kit - Builder Gel - Clear DATE: 9/15/2004FORMULA: 30-8142 REV. NEW

Hazardous Ingredients: CAS # %

N/A 50-100%

Boiling Point: N/A Specific Gravity: Not AvailableVapor Pressure: Not Available (@ 25oC)(mm Hg and Temperature) Melting Point: N/AVapor Density: Not Available Evaporation Rate: Negligible(Air = 1) Water Reactive: NoSolubility in Water: Insoluble Viscosity: 85,000cpsAppearance: Clear Colorless Viscous Gel (@ 25oC) Odor: Characteristic

Flash Point: N/AAuto-Ignition Temperature: N/AFlammability Limits in Air % by Volume: LEL: N/A



Stability: StableConditions to Avoid:Incompatibility (Materials to Avoid):

Direct heat, sunlight, primary and secondary amines, acids and alkalies.Hazardous Polymerization:

May Occur

Polymerization may occur at high temperatures.

Carbon dioxide, dry chemical, or foam.

Unstable

Cool exposed containers with water spray. Use self-contained breathing apparatus in confined areas.Product may polymerize at high temperatures. Polymerization is an exothermic reaction and may produce sufficient heat to cause decomposition and/or rupture containers.



ComponentAcrylated Oligomer

TOXICOLOGICAL DATANone Established




Will Not Occur

Page 1 of 3







Chronic: May cause dermal sensitization in certain individuals.Signs and Symptoms of Exposure:

Redness, itching or swelling of skin. May cause eye irritation.Medical Conditions Generally Aggravated by Exposure:


Eye Contact: Thoroughly flush eyes with water. Contact a physician.Skin Contact:

Inhalation: Not applicable.Ingestion: Do not induce vomiting. Seek medical attention.

Respiratory Protections (Specific Type):Not required with normal use.

Protective Gloves: Recommended for sensitive skin.Eye Protection: Ventilation to be Used:


NoneHygienic Work Practices:



Waste Disposal Methods:Use landfill or incinerate in accordance with applicable local, state, and federal regulations.

Soak up with inert absorbent material (sand, vermiculite). Flush area immediately with water. Prevent water from entering waterways.



Safety goggles.

Local Exhaust

May cause skin irritation in certain individuals. Eye Contact: May be irritating.

Remove contaminated clothing, wash with soap and water. Contact a physician.




Page 2 of 3




Precautions to be taken in Handling and Storing:Store in a cool, shaded, well ventilated, dry area away from direct heat and sunlight.


Page 3 of 3


PRODUCT NAME: IBD The Professional Gel Kit - Builder Gel - Pink DATE: 9/14/2004ITEM: 60412 REV. NEW


N/A 50-100%27813-02-1 10-20%

Boiling Point: N/A Specific Gravity: Approx. 1Vapor Pressure: Not Available (@ 25oC)(mm Hg and Temperature) Melting Point: N/AVapor Density: Not Available Evaporation Rate: Negligible(Air = 1) Water Reactive: NoSolubility in Water: Insoluble Appearance: Thick Viscous Liquid Odor: Faint

Flash Point: > 150oCAuto-Ignition Temperature: N/AFlammability Limits in Air % by Volume: LEL: N/A





May Occur



Unstable






Hydroxypropyl Methacrylate None Established




Will Not Occur

Page 1 of 3






















Safety goggles.

Local Exhaust






Page 2 of 3






Page 3 of 3


PRODUCT NAME: IBD The Professional Gel Kit - Builder Gel - Ultra White DATE: 9/14/2004ITEM: 604003 REV. NEW


N/A 50-100%27813-02-1 10-20%

Boiling Point: N/A Specific Gravity: Approx. 1Vapor Pressure: Not Available (@ 25oC)(mm Hg and Temperature) Melting Point: N/AVapor Density: Not Available Evaporation Rate: Negligible(Air = 1) Water Reactive: NoSolubility in Water: Insoluble Appearance: Thick Viscous Liquid Odor: Faint

Flash Point: > 150oCAuto-Ignition Temperature: N/AFlammability Limits in Air % by Volume: LEL: N/A





May Occur



Unstable










Will Not Occur

Page 1 of 3






















Safety goggles.

Local Exhaust






Page 2 of 3






Page 3 of 3


PRODUCT NAME: IBD Professional Gel Kit - Cleanser Plus DATE: 9/15/2004FORMULA: 30-8280 REV. NEW

CAS # %67-63-0 ~90%

141-78-6 ~5%

67-64-1 ~5%

Boiling Point: N/A Specific Gravity: 0.79Vapor Pressure: Not Determined (@ 25oC)(mm Hg and Temperature) Melting Point: N/AVapor Density: Not Determined Evaporation Rate: N/A(Air = 1) Water Reactive: N/ASolubility in Water: Miscible Appearance: Clear Colorless Liquid Odor: Characteristic

Flash Point and Method Used: 69oF (ASTM)Auto-Ignition Temperature: N/AFlammability Limits in Air % by Volume: LEL: N/A

UEL: N/AExtinguisher Media:Special Fire Fighting Procedures: In case of fire: keep drums, etc., cool by spraying with water. Unusual Fire and Explosion Hazards:





Isopropyl AlcoholTOXICOLOGICAL DATA

ACGIH TLV/TWA: 400 ppm

OSHA PEL/TWA: 400 ppm

Ethyl Acetate ACGIH TLV/TWA: 400 ppm


Acetone ACGIH TLV/TWA: 750 ppm


All standard fire fighting media.

Dangerous fire / negligible explosion hazard when exposed to heat or flame. Vapor-air mixtures is explosive above flash point.


Page 1 of 3





Strong acids, oxidizing agents, strong alkalis, and aliphatic amines.Hazardous Decomposition:





Chronic: Skin-slight irritation to dermatitis. Eyes-irritation to conjunctivitis.Signs and Symptoms of Exposure:

Headache, dizziness, nausea, confusion, narcosis.Emergency First Aid Procedures:

Eye Contact: Wash thoroughly with water while lifting upper and lower lids.Skin Contact:

Inhalation:

Ingestion:

Respiratory Protections (Specific Type):Air purifying respirator.

Protective Gloves: Rubber glovesEye Protection: Ventilation to be Used:

Other Protective Clothing and Equipment:None




Will Not Occur

IARC Monograph

Keep away from heat, sparks and flame. Avoid any source of ignition.


Safety goggles.

Local Exhaust

Remove contaminated clothes, wash affected area with soap and large amounts of water.Remove from exposure area. If breathing has stopped, perform artificial respiration.Give activated charcoal. Give oxygen if respiration is depressed. Seek professional help immediately.

Other (Specify) Special - Explosion Proof

Unstable

Aluminum: dissolution is exothermic. Thermal decomposition: products may include toxic oxides of carbon.

Ingestion-decreased blood pressure and pulse rate, nausea, and hallucinations.

Not Listed

Page 2 of 3




Hygienic Work Practices:Good Manufacturing Practices.


Waste Disposal Methods:Dispose of in accordance with your local, state, and federal regulations.

Precautions to be taken in Handling and Storing:Store away from heat or flame.

Other Precautions and/or Special Hazards:No smoking, flames, or flares in hazard area.

For small spills, cover with sand and place into tight containers for later disposal. For large spills, dike far ahead of spill, cover with sand and place into tight containers for later disposal.


Page 3 of 3


PRODUCT NAME: IBD The Professional Gel Kit - Gel Polish - Techno Ruby DATE: 11/8/2004ITEM: 60613 REV. NEW

CAS # %N/A 50-100%

27813-02-1 10-20%

Boiling Point: N/A Specific Gravity: Approximately 1.00Vapor Pressure: Not Available (@ 25oC)(mm Hg and Temperature) Melting Point: N/AVapor Density: Not Available Evaporation Rate: Negligible(Air = 1) Water Reactive: NoSolubility in Water: Insoluble Appearance: Thick Viscous Liquid Odor: Faint Odor

Flash Point and Method Used: 188oF (Tag Closed Cup)Auto-Ignition Temperature: N/AFlammability Limits in Air % by Volume: LEL: N/A




Direct heat, sunlight, primary and secondary amines, acids, and alkalies.Hazardous Polymerization:

May Occur


CO2, dry chemical, or foam.

Unstable


Hydroxypropyl Methacrylate


None Established

Hazardous Ingredients:Component TOXICOLOGICAL DATA

Acrylated Oligomer None Established



Will Not Occur



Page 1 of 3














Local Exhaust Special Other Protective Clothing and Equipment:








Safety goggles.

Other (Specify)

May cause skin irritation in certain individuals. Eye contact: may be irritating.


Mechanical (General)




Page 2 of 3






Page 3 of 3


PRODUCT NAME: IBD Professional Gel Kit - Nail Prep DATE: 9/24/2004FORMULA: 30-8126 REV. NEW

CAS # %67-63-0 50-90%

67-64-1 1-10%

Boiling Point: N/A Specific Gravity: 0.79Vapor Pressure: Not Determined (@ 25oC)(mm Hg and Temperature) Melting Point: N/AVapor Density: Not Determined Evaporation Rate: N/A(Air = 1) Water Reactive: N/ASolubility in Water: Miscible Appearance: Clear Colorless Liquid Odor: Characteristic

Flash Point and Method Used: 45oF (ASTM 93)Auto-Ignition Temperature: N/AFlammability Limits in Air % by Volume: LEL: N/A



Stability: StableConditions to Avoid:

For massive fire, use unmanned hose holder or monitor nozzles, or else withdraw from area and let burn.

ACGIH TLV/TWA: 400 ppm








Acetone

TOXICOLOGICAL DATAIsopropyl Alcohol ACGIH TLV/TWA:

750 ppmOSHA PEL/TWA:

1000 ppm

Unstable

Dry chemical, carbon dioxide, water spray, or alcohol foam.

Dangerous fire/negligible explosion hazard when exposed to heat or flame. Vapor-air mixture is explosive above flash point.

Excessive heat or flame.

Page 1 of 3




Incompatibility (Materials to Avoid):Strong acids, oxidizing agents, strong alkalis, & amines aliphatic.

Hazardous Decomposition:





Chronic: Skin-slight irritation to dermatitis. Eye-irritation to conjunctivitis.Signs and Symptoms of Exposure:

Headaches, dizziness, nausea, confusion, and narcosis.Medical Conditions Generally Aggravated by Exposure:

No adverse effects are known.Emergency First Aid Procedures:

Eye Contact: Wash thoroughly with water while lifting upper and lower lids.Skin Contact:

Inhalation:

Ingestion:

Respiratory Protections (Specific Type):Air-purifying respirator.

Protective Gloves: Rubber GlovesEye Protection: Ventilation to be Used:

Local ExhaustOther Protective Clothing and Equipment:

When handling large quantities, apron and rubber boots.Hygienic Work Practices:

Good Manufacturing Practices. Avoid contact with skin and eyes, work in well ventilated area.

Aluminum: Dissolution is exothermic. Thermal decomposition of products may include toxic oxides of carbon.

Indigestion-decreased blood pressure and pulse rate, nausea, and hallucinations.

Remove contaminated clothes, wash affected area with soap and large amounts of water.Remove from exposure area. If breathing has stopped, perform artificial respiration.Give activated charcoal. Give oxygen if respiration is depressed. Seek professional help immediately.

Mechanical (General)



Will Not Occur

Safety Goggles

Special: Explosion Proof



Page 2 of 3





Waste Disposal Methods:Dispose of in accordance with your local, state, and federal regulations.


Other Precautions and/or Special Hazards:No smoking, flames, or flares in hazardous area. Store away from heat or flame.

Large Spill-Dike far ahead of spill, cover with sand and place into tight containers for later disposal.

Store away from acids, amines, oxidizing materials. Should be stored in containers which meet the bonding and grounding guidelines specified in NFPA88-1983.

Small Spill-Cover with sand and place into tight containers for later disposal.


Page 3 of 3


PRODUCT NAME: IBD The Professional Gel Kit - Ultra Seal - Clear DATE: 9/14/2004ITEM: 60504 REV. NEW

Hazardous Ingredients:CAS # %

N/A 50-100%

27813-02-1 0-10%97-63-2 0-10%

Boiling Point: Not Available Specific Gravity: Approx. 1Vapor Pressure: Not Available (@ 25oC)(mm Hg and Temperature) Melting Point: N/AVapor Density: Above 1 Evaporation Rate: Negligible(Air = 1) Water Reactive: NoSolubility in Water: Insoluble Appearance: Odor: Slight Acrylic Odor

Flash Point: > 180oF (PMCC)Auto-Ignition Temperature: N/AFlammability Limits in Air % by Volume: LEL: N/A




None

Product may polymerize at high temperatures. Polymerization is an exothermic reaction and may produce sufficient heat to cause thermal decomposition and/or rupture of containers.


Elevated temperatures, ultraviolet light, free radical initiators, amines.


Clear, Colorless, Viscous Liquid


Ethyl Methacrylate None Established

28961-43-5 10-20%None Established

Ethoxylated Trimethylolpropane Triacrylate Ester

None Established


Foam, dry chemical, or carbon dioxide.Cool exposed containers with water spray. In case of fire, wear self-contained breathing apparatus and protective clothing.


Unstable



TOXICOLOGICAL DATA

Page 1 of 3







Health Hazards: Acute:Chronic: Skin contact - may cause sensitization.

Signs and Symptoms of Exposure:

Medical Conditions Generally Aggravated by Exposure:None known.

Emergency First Aid Procedures:Eye Contact:

Skin Contact:

Inhalation: Not applicable.Ingestion: Immediately consult a physician.

Respiratory Protections (Specific Type):In case of high vapor concentrations, wear self-contained breathing apparatus.

Protective Gloves: Rubber gloves.Eye Protection: Ventilation to be Used:

Other Protective Clothing and Equipment:When handling large quantities: apron and rubber goggles.

Hygienic Work Practices:Avoid contact with eyes, skin, and mucous membranes.



Absorb with inert material (i.e. sawdust, sand), collect in closed containers and dispose of as recommended. Avoid skin contact.

Chemical goggles.

Local Exhaust Mechanical (general) Special

Irritated skin and eyes, reddening or swelling, may cause sensitization with repeated exposure.

Flush eyes with water with eyelids retracted for at least 15 minutes: consult a physician.Immediately was with soap and water; remove contaminated clothing; if reddening or swelling occurs, consult a physician.



Skin Absorption Eye Contact

Skin contact - slightly irritating; Eye contact - may be irritating

Will Not Occur


Page 2 of 3




Waste Disposal Methods:Incineration or landfill according to federal, state, and local regulations.


Other Precautions and/or Special Hazards:After expiration of storage time, spontaneous polymerization may occur.

Store below 30oC in a well ventilated area, away from direct sunlight, oxidizing or reducing agents.

Page 3 of 3

MATERIAL SAFETY DATA SHEET · Section 5. Health Hazard Data May be harmful if inhaled. May cause...

Documents

Transcript of MATERIAL SAFETY DATA SHEET · Section 5. Health Hazard Data May be harmful if inhaled. May cause...