Manufacturers of Concrete Sawing & Drilling Equipment
Transcript of Manufacturers of Concrete Sawing & Drilling Equipment
Manufacturers of
Concrete Sawing & Drilling Equipment
WALCUT™ HANDICUT™ CORCUT™
HYDRAPAC™ Power Modules
“Cut It Out!”sm
GDM Technologies
1910 South Fremont Drive, Salt Lake City, UT 84104
Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056
email : [email protected] - www.gdmsaws.com
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Wall Saws - HANDICUT
3 New! MODEL 24/30 GT AIR WALCUT SAW
4 Pneumatic Wall Saws - WALCUT
Models 24 and 30
5 Hydraulic Wall Saws - WALCUT
Models 24H & 30H
6 Electric Hi Cycle Wall Saws - WALCUT Models
24E & 30E
7 Hydraulic Wall Saws - WALCUT
Model 24LG “Little Green Machine”
Wall Saw Accessories
8 New “Walcut Wizard” Pneumatic
Depth Control
8 New “Walcut Wizard” Hydraulic Depth Control
8 New RMT 200 Pneumatic Remote
8 New RMT 300 Hydraulic Remote
9 WALCUT Wall Saw Caddy
10 WALCUT Tracks
10 Universal WALCUT Tracking Carriage
11 Blade Guards for WALCUT Wall Saws
11 Silencing/Safety Blade Guards
12 WALCUT Track Tools - Interlock Plates, Plate
Bolts, Alignment Tools, Templates
12 WALCUT Standard & Spaced Blade
Hubs & Caps
12 WALCUT Flushcut Blade Hubs,
Caps, Spacers
13 Custom Blades for WALCUT Saws
Hand Saws - HANDICUT
Hydraulic Models
14 HANDICUT Model 24 HS
15 HANDICUT Model 20HS
16 New! Handicut Model 21 Fixed Base
Hydraulic Handsaw
16 New! Handicut Fixed Base Model 21 Combo Hydraulic Handsaw
17 HANDICUT Model 14HS
GDM Catalog Table of Contents
Hand Saw Accessories
18 Hand Saw Blades for GDM
HANDICUT Saws
18 HANDICUT Blade Hubs & Caps
Drilling Motors & Systems
19 New! TDI BIG CAT 500 Roller Carriage
20 CORCUT 250 & 300 Roller Carriages
20 CORCUT 300 Drilling System
20 CORCUT 250 Drilling System
20 Roller Carriages and Core Drill Stands
21 Vacuum Base Systems
21 Drilling System Posts and Bases
22 2-Speed Milwaukee Electric Motor,
Adaptor & Controls
22 Universal Electric Motors
22 4-Speed Electric Motor, Adaptor & Controls
22 Hi Cycle Motors - 4oo Cycle Motor
23 300-Series Hydraulic CORCUT Drill Head
23 Pneumatic Motors
23 300/2 Series CORCUT Drill Head
23 400-Series CORCUT Drill head
24 CORCUT 200 Drill System
24 CORCUT Accessories - Extensions, Etc
24 Universal WALCUT Track (CORCUT)
24 RMT 250
24 CORCUT 400 Drill System
Power Modules
25 GDM HP350 HYDRAPAC Power Module
25 GDM HP200 HYDRAPAC Power Module 26 New from Ingersoll Rand: Compressor
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 3
Wall Saws
MODEL 24/30 GT AIR WALCUT SAW
THINK GREEN, THINK POWER, THINK GDM.
POWER OF A HYDRAULIC SAW WITH
THE CLEAN EASE OF AN AIR SAW.
CLEAN GREEN AND EARTH FRIENDLY.
Key Features: 1. Dual stage turbine compressor has greater efficiency
2. Only one hose line to the saw
3. Quick Cam easy-off Motor mount for lightweight handling
4. 48 lbs Frame
5. 29 lbs Motor
• Made with strong lightweight aircraft quality components
• Produces up to 25HP (125lbs) Torque
• NO OILER NEEDED - Just CLEAN AIR POWER!
• 50% Quieter than vane Motors
Key Benefits: 1. More Power. More Torque.
2. Air as clean coming out as it is going in - no oiler required
3. Motor self-contained for a cleaner running system
4. Lower air consumption. 40% more efficient at lower rating
5. GDM has the STRAIGHTEST CUT in the industry!
Specifications: 1. RATINGS - 14 HP - continuously rating at 94 PSI 220 CFM 25 HP maximum
rating at 150 PSI 365 CFM
2. SPEEDS - rated load speed 1100 RPM adjustable over range, varied by loading
3. DRIVE - self-propelled with two choices of propelling gearboxes
4. DIMENSIONS - 17.5 long 11.5 wide 26.5 high
5. WEIGHT - Self-propelled saw 48 lbs, motor 29 lbs
6. BLADES - maximum suggested size 48” for 21” cutting depth
Includes:
• WALCUT Model 24GT Long Columns Complete Standard Setup:
• (2) 4’ Interconnecting-Interlocking Tracks
• (1) 2’ Interconnecting-Interlocking Track
• 24” Bladeguard, Anchor Template, Track Alignment Tool, Small Parts and
Manual
• 2 Bolt Conversion Kit: includes: GT Carriage, Motor, Gearbox.
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 4
Wall Saws
WALCUT Models 24 and 30 Pneumatic Wall Saws Years of proven field performance with a track
record of dependability efficiency and precision
give WALCUT 24 and 30 the edge in concrete
cutting equipment.
Units provide continuous tracking.
They can change direction
without removing either the saw
or the track from the surface being cut.
Simple design allows mounting on
flat, curved, rough or
discontinuous surfaces.
Features: 1. WALCUT Models. 24 and 30 use the same frames, tracks and blade guards as the hydraulic and electric wall units.
2. Both Models 24 and 30 offer a covered or an enclosed propelling gearbox either manual or pneumatically self-propelled.
3. Self-propelled in either direction. The travel is controlled by the amount of torque adjusted through air regulator. Saw tends to
slow down when encountering obstructions like steel.
4. All controls are conveniently located for ease of operation. Four adjustments do the job.
5. Operate in any position horizontal, vertical, or upside down on any wall, ceiling or floor.
6. Accurate cutting depth is obtained by single acting positive screw feed on Model 24 (10” carriage movement), and double acting
positive screw feed (13” carriage movement) on Model 30.
7. A proven system designed for straight, square, accurate saw cuts of any length, either Model 24 or 30 coupled with GDM tracks
provides rigid and accurate cutting.
8. Factory alignment will last for many months or years depending on usage. A re-alignment feature is built in for customer
convenience and product longevity.
Package Pricing All wall saws may be purchased as complete packages that include tracks, accessories and operating manual. Wall saws may also be
purchased by themselves without accessories or manuals. Prices do not include shipping, handling or taxes.
• WALCUT Model 30 - Complete Package - Standard set-up- self-propelled saw unit. Price includes two (2) 4 ft. interconnecting/ interlocking tracks – one (1) 2 ft. interconnecting/ interlocking track- 30inch blade guard- anchor template- track alignment tool-
small parts- and operation manual. (complete unit ready to go)
• WALCUT Model 30 - Saw Only
• WALCUT Model 24 - Complete Package WALCUT Model 24 pneumatic Wall saw-Complete. Standard set-up- self-propelled
saw unit. Price includes two (2) 4 ft. interconnecting/ interlocking tracks- one (1) 2 ft. interconnecting/ interlocking track- 24inch
blade guard- anchor template- track alignment tool- small parts- and operation manual. (complete unit ready to go)
• WALCUT Model 24 - Saw Only
Specifications: Model 24 1. RATINGS: 9 H.P. continuous-duty rating at 94 psi and
220 cfm or a 15.8 H.P. maximum manufacturer’s rating at
150 psi and 320 cfm.
2. SPEEDS: Rated load speed 1110 RPM adjustable over
range, varied by loading.
3. DRIVE: Manual or self-propelled with two choices of
propelling gearboxes.
4. WEIGHT: Manual: 69 pounds assembled. Self propelled:
76 pounds assembled.
5. DIMENSIONS: 17.5” long x 11.5” wide x 22.5” high.
Medium duty frame.
6. BLADES: Maximum suggested blade size, 42” diameter;
cutting depth of 18”
Specifications: Model 30 1. RATINGS: 9 H.P. continuous-duty rating at 94 psi and
220 cfm or a 15.8 H.P. maximum manufacturer’s users
rating at 150 psi and 320 cfm.
2. SPEEDS: Rated load speed 1110 RPM adjustable over
range, varied by loading
3. DRIVE: Manual or self propelled with two choices of
propelling gearboxes.
4. WEIGHT: Manual 82 pounds assembled. Self-
propelled: 89 pounds assembled.
5. DIMENSIONS: 21” long x 13”wide x 27” high.
Heavy duty frame.
6. BLADES: Maximum suggested blade size: 48”
diameter; cutting depth of 21”
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 5
GDM Electric 400Z Inverter/Controller
In the tradition of GDM quality, dependability and ease of operation, we present GDM’s new E400 Hertz Hicycle Inverter /
Controller. Made in the USA, it is designed to power GDM’s Model 24E and 30E Walcut Saws. GDM’s E400Z produces constant
torque at variable speeds with soft start in forward or reverse direction. Now the saw operator has a broader power range with blade
speed control.
Adding the GDM high torque gearbox to the Walcut
Saw nearly doubles the power, for really large
blades and the most difficult sawing conditions.
Controlled 400 hertz power, variable speeds, and
constant torque rotating in either direction
produces faster sawing with the straight cuts that
no other wall saw can match.
400Z Specifications:
1. Ratings to 40 HP Depending On Power Setting
2. Walcut High Speed Gear Box: Variable 0-1400 RPMs
3. Walcut High Torque Gear Box: Variable 0-800 RPMs
4. HP with Constant Torque at all speeds
5. Forward and Reversing Switch With Soft Start
6. 480 V 3-Phase 60hz to 480 400hz
7. 480V 3 Phase 60hz to 480V 400hz Conversion
8. Overload Current Capacity Up to 180%
9. Strong Aluminum Air Cooled Case- Only 65lbs
10. Operator Friendly Controls
11. 100 FT Electrical Cord with Waterproof Connectors
12. GDM Quality & Dependability
13. Made in The USA
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 6
Wall Saws
WALCUT Models 24H & 30H Hydraulic Wall Saws In the tradition of GDM quality we are Manufacturing these high
powered, hydraulic, track-mounted saws using the same frames,
tracks and blade guards as our widely accepted air-powered units.
Both Models 24H and 30H are provided with the enclosed propelling
gearbox, either manual or hydraulically self propelled.
Quick removable hydraulic motor/manifold for ease of handling.
Units provide continuous tracking. They can change direction without
removing either the saw or the track from the surface being cut. Simple design allows
mounting on flat, curved, rough or discontinuous surfaces
Features: Models 24H & 30H 1. WALCUT Models 24H and 30H use the same frames, tracks and blade guards as the air powered units. For complete track information,
refer to WALCUT Tracks.
2. Both Models 24H and 30H are provided with the enclosed propelling gearbox, either manual or self-propelled.
3. A calibrated flow control valve at the saw allows full continuous blade speed adjustment at constant torque.
4. Special GDM controllable constant-torque, self-propelling drive that can be adjusted by one knob, automatically slowing forward speed
when encountering steel reinforcing or other discontinuities.
5. Compact, easily visible pressure gauge at manifold location for desired blade drive force.
6. Quickly removable hydraulic motor/manifold on two bolt pattern with motor and blade gearbox are independently mounted on saw
carriage, leaving a light-weight frame for handling and mounting on tracks.
7. Motors of different displacement can be quickly interchanged on the saw frame without disturbing blade alignment. Motors of different
displacement allow maximum HP at different speeds (blade sizes).
8. All controls conveniently located on a manifold mounted on the hydraulic saw. Manifold and manifold plumbing can be easily transferred
between motors.
9. An auxiliary hand crank is available to manually position wall saws on the track. Remove the weight of the manifold and motor with
this feature.
Package All wall saws may be purchased as complete packages that include tracks, accessories and operating manual. Wall saws may also be purchased
by themselves without accessories or manuals. See below. Prices do not include shipping, handling or taxes.
• WALCUT Model 30H - Complete Package - Standard set-up- self-propelled saw unit. Price includes two (2) 4 ft. interconnecting/
interlocking tracks- one (1) 2 ft. interconnecting/ interlocking track- 30inch blade guard- anchor template- track alignment tool- small
parts- and operation manual. (complete unit ready to go)
• WALCUT Model 30H- Saw Only
• WALCUT Model 24H - Complete Package WALCUT Model 24 hydraulic Wall saw-Complete. Standard set-up- self-propelled saw unit. Price includes two (2) 4 ft. interconnecting/ interlocking tracks- one (1) 2 ft. interconnecting/ interlocking track- 24inch blade guard-
anchor template- track alignment tool- small parts- and operation manual. (complete unit ready to go)
• WALCUT Model 24H - Saw Only.
Specifications: Model 24H 1. RATINGS: 22-35 H.P depending on motor displacement.
2. SPEEDS: Continuously variable to maximum ratings for five
different interchangeable motor displacements. Ratings vary
from 2100-1000 RPM maximum, depending on motor
displacement.
3. PRESSURE: Direct-reading pressure gauge for controlled
loading.
4. DRIVE: Manual or self-propelled.
5. WEIGHT-. Manual: 60 pounds assembled. Self-propelled: 66
pounds assembled. Frame (less motor/manifold): 52 pounds.
6. DIMENSIONS: 17.5” long x 11.5” wide x 22.5” high (with
standard GDM column).
7. BLADES: Maximum suggested blade size, 42” diameter;
cutting depth of 18”.
Specifications: Model 30H 1. RATINGS: 30-50 H.P depending on motor displacement.
2. SPEEDS: Continuously variable to maximum ratings for five
different interchangeable motor displacements. Ratings vary
from 2000-800 RPM maximum, depending on motor
displacement.
3. PRESSURE: Direct-reading pressure gauge for controlled
loading.
4. DRIVE: Manual or self-propelled.
5. WEIGHT. Manual: 76 pounds assembled. Self-propelled: 82
pounds assembled. Frame (less motor/manifold) 65 pounds.
6. DIMENSIONS: 21” long x 13” wide x 27” high (with
standard GDM column).
7. BLADES: Maximum suggested blade size, 72” diameter;
cutting depth of 33”.
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 7
Wall Saws
WALCUT Models 24E & 30E Electric Hi Cycle Wall Saws In the tradition of GDM quality we are manufacturing track-mounted saw units for high powered 400 cycle electric motors using the same
frames, tracks and blade guards as our air and hydraulic powered units. Both Models 24E and 30E are provided with the enclosed propelling
gearbox, either manual or pneumatically self-propelled. Quickly removable electric motor on a camlock system. Units provide continuous
tracking. They can change direction without removing either the saw or the track from the surface being cut. Simple design allows mounting on
flat, curved, rough or discontinuous surfaces.
Features: Models 24E & 30E 1. Modular Design complements GDM equipment in the field.
2. WALCUT Models 24E and 30E use the same or similar frames and the same tracks and blade guards as the air and hydraulic powered
units. For complete track information, refer to WALCUT Tracks.
3. Both Models 24E and 30E are provided with enclosed propelling gearbox, either manual or self-propelled pneumatically.
4. Special GDM controllable, constant-torque, air self-propelling drive that can he adjusted by one knob, automatically slowing forward
speed when encountering steel reinforcing or other discontinuities.
5. Quick removable electric motor on a camlock system. The motor and blade gearbox are independently mounted on GDM saw carriage,
leaving a light-weight frame for handling and mounting on tracks.
6. Motors can be quickly interchanged on the saw frame without disturbing blade alignment.
7. Each model comes with two different blade gear box ratios that can be quickly interchanged on the saw frame. This allows for your choice
of blade speeds.
Package Pricing All wall saws may be purchased as complete packages that include tracks, accessories and operating manual. Wall saws may also be purchased
by themselves without
accessories or manuals. See below. Prices do not include shipping, handling or taxes.
• WALCUT Model 30E - WALCUT Model 30E Wall saw-complete. Model 30E Wall Saw to take 400 cycle/second motors* Standard
set-up- air self-propelled Price includes two (2) blade gearboxes - one for 1400 rpm and one for 800 rpm (speeds for 2500 rpm motor)*-
two (2) 4 ft. interconnecting/interlocking tracks- one (1) 2 ft. interconnecting/ interlocking track- 30inch blade guard- anchor template-
track alignment tool- motor adaptor- small parts and operation manual.
• WALCUT Model 30E - Saw Only
• WALCUT Model 24E - Complete Package Model 24e Wall Saw to take 400 cycle/second motors* Standard set-up, air self-propelled
Price includes two (2) blade gearboxes one for 1400 rpm and one for 800 rpm (speeds for 2500 rpm motor) *, two (2) 4 ft.
interconnecting/interlocking tracks, one (1) 2 ft. interconnecting/ interlocking track, 24” blade guard, anchor template, track alignment
tool, motor adaptor, small parts and operation manual.
• WALCUT Model 24E - Saw Only.
Specifications: Model 24E 1. RATINGS: Depends on motor used, 12 H.P to 25 H.P
2. SPEEDS: Depends on motor and gearbox combination, four
increments: 550 and 960 or 800 and 1400.
3. DRIVE: Manual or air self-propelled.
4. WEIGHT: Manual: 47 pounds assembled less motor. * Self-
propelled: 52 pounds assembled less motor. *
5. DIMENSIONS: 17.5” long x 11.5” wide x 22.5” high (with
standard GDM column).
6. BLADES: Maximum suggested blade size, 42” diameter; cutting
depth of 18”. *Less motor weight. The most popular 20 H.P. motor weighs 43 pounds.
Specifications: Model 30E 1. RATINGS: Depends on motor used, 12 H.P to 25 H.P
2. SPEEDS: Depends on motor and gearbox combination, four
increments: 550 and 960 or 800 and 1400.
3. DRIVE: Manual or air self-propelled.
4. WEIGHT: Manual: 60 pounds assembled less motor. * Self-
propelled: 65 pounds assembled less motor. *
5. DIMENSIONS: 21” long x 13” wide x 27” high (with standard
GDM column).
6. BLADES: Maximum suggested blade size, 60” diameter; cutting
depth of 27”. *Less motor weight. The most popular 20 H.P. motor weighs 43 pounds.
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 8
Wall Saws
New WALCUT Model 24 LG “The Little Green Machine”
In the tradition of GDM quality, we are manufacturing this hydraulic, track-mounted saw using the same frame, track and blade
guards as our Model 24H Self-Propelled Wall Saw.
The Model 24LG is provided with an enclosed, manually-propelled gearbox and a simple flow-control manifold.
Features: 1. Light weight, rigid alloy frame
2. Simple, hand-operated controls
3. Enclosed manual-propelling gearbox with hand crank
4. Accepts Model 24H or 30H Blade Guards and Track
5. Motors of different displacements are available
Specifications: 1. RATINGS: 15 to 30 HP depending on motor displacement
2. SPEEDS: Continuously variable to maximum ratings
3. MOTORS: Three different interchangeable motors
4. DRIVE: Manually propelled
5. WEIGHT: 56 lbs assembled
6. DIMENSIONS: 17.5” long x 11.5” wide x 22.5” high
7. BLADES: Maximum blade suggested 42”
WALCUT Model 24LG - Standard setup includes manually-propelled saw unit; two 4-foot interlocking, interconnecting track; 24
inch blade guard, anchor template, track alignment tool; small parts; operation manual. Complete Setup:
WALCUT Model 24LG Saw Only:
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 9
Accessories – Wall Saws
New “Walcut Wizard” Pneumatic Depth Control
This remote self-propelling depth control has added a new dimension to the
GDM Walcut Wall Saw, allowing the operator control at a cleaner, safer
distance from the work being performed. The “Walcut Wizard” enables the
operator to plunge or retract the saw blade at a controlled rate. The remote
control “Walcut Wizard” works in conjunction with the new “RMT 200” multi-
function remote on the GDM Electric and Pneumatic Wall Saws.
New RMT 200 Pneumatic Remote
Designed for remote control of pneumatic self-propelling
gearboxes, this multi-function unit controls speed and
direction, at a cleaner, safer distance from your Walcut
wall saw. The new GDM hand held remote control
device is easy to operate. This unit is a welcome addition
to the clean and simple use of the GDM electric and
pneumatic Walcut Wall Saws.
New “Walcut Wizard" Hydraulic Depth Control
The Remote Self-propelling depth control has added a new dimension to GDM
Walcut Wall Saws, allowing operator control at a cleaner, safer distance from
the work being performed. The new depth control enables the operator to plunge
or retract the saw blade at a controlled rate. The remote control “Walcut Wiz”
works in conjunction with the new GDM multi-function RMT 300
Hydraulic Remote.
New RMT 300 Hydraulic Remote
Now you can safely operate your sawing and drilling equipment remotely. This
new hydraulic multi-function remote control works in conjunction with GDM
Walcut wall saws, Corcut core drills and wire saws. The unit is designed to
control direction, speed and flow (torque) up to 35 gpm. This remote unit directs
the drive and self-propelling systems allowing the operator ease in maneuvering
the up and down and forward and reverse applications of the equipment.
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 10
Accessories – Wall Saws New Walcut EZ Mount Base
You asked for it and GDM made it. Model 24 Walcut Wall Saws can mount anywhere on the track. The new EZ Mount Base with
movable camfollowers snaps in and out to transform the GDM Model 24 Wall Saw into an easily mounted wall saw. A simple track
adjustment with our new “hold off” leveling screws completes the transformation. The leveling screws aid in track mounting on
uneven surfaces and give the new base the required room to operate. This combines the bulletproof stability of GDM equipment with
the convenience of mounting the wall saw anywhere on the track.
WALCUT Caddy A transporter for your WALCUT Saw.
This is a caddy to carry all your WALCUT components from your truck to your jobsite location.
The caddy carries the following: WALCUT saw, WALCUT track (ten feet), WALCUT Blade Guard,
saw blades, and tools. The caddy has 13 inch heavy-duty pneumatic tires for easy maneuvering.
Heavy tube construction. Rated at 800 lbs.
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 11
Universal WALCUT Tracking Carriage
Thoughtfully engineered and modularly designed
to complement GDM tracks. “The trick is in the
track” takes on new meaning with this tracking
plate. Use this in conjunction with our WALCUT
Tracks, any GDM CORCUT drill, or with a
number of different tools, such as our HANDICUT
Saw for precision movement back and forth. This
carriage gives you the edge in line drilling, cutting
or breaking with reduced set-up time.
Accessories – Wall Saws
WALCUT Tracks
A Stable Continuous Tracking System “The Trick is in the Track”
WALCUT interconnecting tracks insure the stability; accuracy and mobility of the total
WALCUT Sawing System.
• Each track is matched and interchangeable, butted and aligned for continuous cutting.
• Precise pin and dowel connection from one track to the next with matching gear racks.
• Lightweight for easy handling.
• Available in 5, 4, 3, 2 and 1 foot sections, allowing any job to be laid out in one foot increments and handled as one piece when interlocked.
Track Pricing: T3000-5A 5 ft. Track section
T3000-4A 4 ft. Track section
T3000-3A 3 ft. Track section
T3000-2A 2 ft. Track section
T3000-1A 1 ft. Track section
WALCUT Curved Tracks
(T3000C) curved tracks can be made to order
to fit diameters as small as 10 to 12 feet.
Standard track parts are bent (rolled) to the
correct radius before assembly. Only minor
adjustments are needed to have the WALCUT
saw fit each diameter. Although the tracks,
once curved, can only be used for the designed
diameter, the saw can always be readjusted to fit any curve.
Features: 1. Each track section can he butted and aligned for
2. Tracks are optionally interlocking:
a. Interlock plates between tracks are in the open and easily accessible.
b. A bolt in an interlock plate can also function as a safety stop.
c. The hold-down force of a bolt in one track is transferred to the next track
through the interlock plate.
3. Safety stops are gained through the use of vice grips and leveling screw
holes in addition to the interlock plates.
4. Leveling screws are provided for leveling and stiffening the track on uneven
surfaces. Screws are in the open and easily accessible.
6. Anchor bolt slots are long slots for maximum flexibility in positioning. Any
number of bolts can be put in any position. Long slots allow for adding a
bolt in slots after the track is up.
a. Slot also allows for sliding of track on the bolt hold-down has to reposition
the track without removing the saw.
b. Slot is wide enough to easily locate anchor bolts in the area and allows for
some horizontal shift in the track. c. Track can be swiveled on the wall with the saw on the track.
7. Hold-down plate (for anchor), using track alignment tool supplied, allows
for easy alignment of track.
8. Lightweight track designed for easy handling.
Specifications: 1. DIMENSIONS:
a. 1-3/4” high x 8-1/2” wide x 48” long with 6
level screws, anchor slot 1-1/4” wide x 17”
long
b. b. 1-3/4” high x 8-1/2” wide x 24” long with 4
level screws, anchor slot 1-1/4” wide x 17”
long
c. c. 1-3/4” high x 8-1/2” wide x 12” long with 4
level screws, anchor slot 1-1/4” wide x 5” long
2. WEIGHT
a. 48” - 28 pounds
b. 24” - 14 pounds
c. 12” - 7 pounds
3. MATERIALS
a. Base: Magnesium-aluminum alloy
b. Rail: Chrome steel
c. Rack: Carbon steel
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 12
Accessories – Wall Saws
WALCUT Blade Guards Rigid lightweight aluminum WALCUT Guards are available for 18”
through 72” diameter blades. WALCUT Blade guards consist of a
one, two or three piece unit with snap-on removable ends, introduced
by GDM. The blade guard front (or rear) removes to finish a cut up to
obstructions. An enclosed novel water jet system allows coolant water
to be distributed across the entire blade surface. Designed especially
for GDM WALCUT Concrete Cutting Equipment.
Features: 1. Built of lightweight, rigid, brushed aluminum construction. Each
guard has a bend on the bottom surface for rigidity and to restrict the
water from splashing outside. Water flaps are provided on each end to
confine water spray.
2. The water jet system is completely enclosed in the guard and
mounted so that it directs water near the blade hub to be carried by
centrifugal force over the entire blade. This method fully cools and
flushes any blade diameter that will fit in the guard.
3. The 18” diameter guard: is a single piece construction and adapts to
both WALCUT Model 24/24H/24E and 30/30H/30E saws.
4. The 24” diameter guard: comes with front end removable (single-
ended) to complete a cut. The removable ends are locked into
position with screw knobs. Adapts to both WALCUT 24/24H/24E
and 30/30H/30E saws.
5. The 24” to 60” diameter guards: come either single-ended or with
both ends removable (double-ended). This allows the saw unit to
finish a cut up to obstructions with the removal of the appropriate
guard end. Example: ceiling to floor or wall to wall. These guards are
made adaptable to WALCUT Model 30, but can be made
interchangeable with the WALCUT Model 24.
6. The 36” to 72” diameter guards: are reinforced with embossed
indentation channel for additional rigidity, and an extra snap lock is
provided between the main body and the removable ends to reduce
vibration. A handle extension is provided to fit over the saw depth
screw to allow the depth screw crank handle to clear the guard in the
up position.
Silencing/Safety Blade Guard: Designed to reduce noise levels and provide additional safety
precautions while cutting. This stationary bladeguard completely
encloses the blade during operation. The blade is never exposed at
any cutting depth. The two-piece aluminum construction is rigid
and light-weight. The front panel is removable for
convenience. We feature our enclosed GDM Water
Jet System which allows coolant water to be
distributed across the entire blade surface.
Available in a variety of sizes.
“A Guard for All Reasons”
Specifications: • 18” GUARD: Fits 18” diameter blade or smaller. Once piece
construction. 22” long x 11” high x 2-1/4” wide - 6 lbs.
• 24” GUARD: Fits 24” diameter blade or smaller. Single or
double ended construction. 28” long x 14” high x 2-1/4” wide
- 8 lbs.
• 30” GUARD: Fits 30” diameter blade or smaller. Single or
double ended construction. 34” long x 17” high x 2-1/4” wide
- 12 lbs.
• 36” GUARD: Fits 36” diameter blade or smaller. Single
or double ended construction with embossed indentation
and lock clips. 40” long x 20” high x 2-1/4” wide - 16
lbs.
• 42” GUARD Fits 42” diameter blade or smaller. Single or
double ended construction with reinforcing embossed
indentation and lock clips. 46” long x 23” high x 2-1/4” wide
- 20 lbs.
• 48” GUARD Fits 48” diameter blade or smaller. Single or
double ended construction with reinforcing embossed
indentation and lock clips. 52” long x 26” high x 2-1/4” wide
- 24 lbs.
• 60” GUARD Fits 60” diameter blade or smaller. Single or double ended construction with six reinforcing embossed indentation and
lock clips. 60” long x 30” high x 3” wide - 30 lbs.
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 13
Accessories – Wall Saws
WALCUT Tools & Accessories
A. (3000A) Saw Alignment Tool. Tool bolts to the WALCUT blade hub, and when rotated or
swung back & forth between track rail edges, dial gauge reads saw (blade) alignment to track.
B. (3000B) Eccentric Wrench. Special GDM tool to fit eccentric bushing for aligning the blade
with the track, as well as adjusting the fit of the camfollowers to track rails. Tips on fluted
front end slot into bushings and 1/4” hex on back end fits any 1/4” socket tool.
C. (RUC3) In-line-Oiler for use with pneumatic powered saws. All pneumatic vane motors
require a light oil film to reduce friction and overheating.
D. (30222-7AH) Hydraulic Hand Crank. For use with WALCUT Models 24H & 30H. When
con- nected to self-propelling gearbox, serves as a manual means of moving the saw into
position or off and on the track. Functions with the motor/manifold assembly off or on the
saw frame. With the motor/manifold off the frame, saw weight and bulk is reduced for ease of
handling in difficult setups.
WALCUT Standard & Spaced Blade Hubs & Caps
GDM’s blade hubs unique design holds the blade on the hub
arbor instead of the blade spindle, quick interchange can be made
to new standard or special application hubs.
E. (30085) Standard GDM Blade Hub with 1-3/8” arbor
3/8” long to take one to three standard blades or spacers.
F. (30086) Standard GDM Blade Cap has counterbore to
adjust to one to three standard blades or spacers.
G. (30085L) Special GDM Blade Hub with 1-3/8” arbor &
with lengths up to 3” for multiple blades and spacers.
Normally 7/8” long hubs (the longest that will allow
spacing to a standard width blade guard) are a stock item.
Other lengths made to order. H. (30085- 1” ) Special GDM blade hub with 1” arbor,
3/8”long to take one or three blades and spacers.
I. (30086-1”) Special GDM blade cap with 1” counter bore to adjust to one to three blades
or spacers.
J. (300851-1”) Special GDM blade hub with 1” arbor and with lengths up to 3” for multiple blade
and spacers. Normally 7/8” long hubs are in stock Other lengths made to order.
K. Aluminum blade spacers. Normally an assortment are in stock.
WALCUT Track Tools L. (T3013) Interlock plates. Locks tracks together making firmer position to cutting surface and
quicker repositioning.
M. (T3014,15) Interlock Plate screws and washers.
N. (T3016) Hold-down plate. Case hardened steel plate used with wide slot tracks, thus eliminating
close tolerance problems when drilling anchors. Counterbore takes standard socket. Available for
use with either 3/8” or 1/2” bolt..
O. (T3017) Hold-Down Plate Bolt. Grade 5 hardened bolts, standard 1-1/4” long. Special grade 8
alloy steel long bolts available for safety swivel bolts.
P. (T3023) Track Alignment Tool. Use to align track in exact position without harmful use of a
hammer. A pin fits in special holes in the hold down plates, the camfollower fits against the track
slot, and a 6/1 leverage ratio allows the track to be moved to align saw exactly on cut line.
Q. (T3024) Track Anchor Layout Template. Simplifies locating position of anchors to mount
WALCUT tracks. Complete layouts can be made ahead of time without measurements or lifting
of track.
WALCUT Flushcut Hub
R. (30085FL) Special
flushcut blade hub. Uses
a very short hub length of
a normal blade width and
three threaded holes to fit
a countersunk hole
pattern in the mated
blade. Special
Bladeguards with special
water jets to fit are
available.
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 14
Accessories – Wall Saws
Custom Blades for WALCUT Saws Professional Grade Wall Saw Blades Custom designed for GDM Walcut Saws
All blades supplied with 1-3/8 inch center hole in GDM flush cut pattern.
One inch arbor available on request
Blade Size
18 X 187 X 1-3/8 18 X 220 X 1-3/8
24 X 187 X 1-3/8 24 X 220 X 1-3/8
26 X 187 X 1-3/8 26 X 220 X 1-3/8
30 X 187 X 1-3/8 30 X 220 X 1-3/8
32 X 187 X 1-3/8 32 X 220 X 1-3/8
36 X 187 X 1-3/8 36 X 220 X 1-3/8
42 X 187 X 1-3/8 42 X 220 X 1-3/8
48 X 187 X 1-3/8 48 X 220 X 1-3/8
020 Split Pro S for Air Powered Saws
060 Split Pro S for Low hp Hydraulic or Hicycle
110 Split Pro S for higher hp Hydraulic or Hicycle
140 Split Pro S for High hp Hydraulic Abrasive Concrete
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 15
Hand Saws
HANDICUT Model 24 HS Hydraulic Hand Saw New from GDM Technologies The HANDICUT hydraulic hand saw is a power-packed
portable unit. Designed for those hard to get to jobs, this
hand-held unit can cut in any position. The power and durability
are ideal for cutting up to 10” concrete or block walls
from one side. A versatile tool for multiple applications,
the HANDICUT allows the operator a more efficient way to
obtain control and precision while cutting. One of the most
dependable lightweight saws on the market, the unit’s
stability and accuracy is unmatched.
Features:
1. 24” blade capacity
2. Adjustable depth control
3. Weighs only 33 lbs.
4. Cuts up to 10.5” from one side
5. Water cooled handle for operator comfort
6. Wide base for straight cuts and operator safety
7. Very stable operator friendly sawing system
8. Light weight aircraft aluminum
9. Also available as a flush cut saw
1. HANDICUT Model 24 HS is a multi-purpose portable unit
which can be operated freehand without saw guides or as a
mini wall saw with guides.
2. The guides are a simple, versatile, inter-connecting
design consisting of two 4’ lengths of angle with spaced
locations for tie downs to the surface being cut. The guides
can be used as:
a. Spaced units confining the HANDICUT base firmly
to the wall being cut.
b. With only one side of the guide acting as a support.
3. The Model 24 HS features a dual-purpose base plate. It
incorporates excellent stability in hand operation and for
alignment in the guide system. The embossed under
surface of the base gives extra rigidity and reduces friction
between the base and the cutting surface.
4. Operates in any position - horizontal, vertical, upside
down. Cuts extremely close to perpendicular on any wall,
ceiling or floor.
5. Accurate cutting depth is controlled by changing lock
position of rear slotted arm on saw.
6. The additional movable slotted guard gives added safety
protection to the operator when making the initial cut and
prevents exposure to the blade.
Specifications: 1. RATING: 10 H.P. Continuous-duty rating @ 2100 psi and 9 gpm.
2. SPEEDS: Continuous variable to maximum ratings.
3. WEIGHT: 32 lbs. (without blade)
4. DIMENSIONS: 28” x 7.5” x 16.5”. Base dimensions: 27” x 7.5” x .5”
5. BLADES: Maximum suggested blade size 24” diameter (cutting depth just over 10”)
Safety Blade Cover
Depth Control
Stable Base
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 16
Hand Saws
HANDICUT Model 20HS Hydraulic Hand Saw
The 20HS HANDICUT hydraulic hand saw is a power-packed portable unit. Designed for those hard to get to jobs, it cuts in any
position. Ideal for cutting up to 8” concrete or block walls from one side.
Using GDM Guide units, the operator can obtain control, accuracy and cutting depth. The HANDICUT hand saw is a versatile tool for
multiple applications.
Features:
1. HANDICUT Model 20HS is a power packed multi-purpose portable unit
which operates freehand without saw guides or operates as a mini wall
saw with guides.
2. Operates in any position - horizontal, vertical, upside down. Cuts close to
perpendicular structures on any wall, ceiling or floor.
3. Quick opening hinge on the base plate allows the tool guard to be opened
90 degrees for blade access and easy installation of large diameter blades
on or off the saw guides.
4. The guides are a simple, versatile, inter-connecting design consisting of
two 4’ lengths of angle with spaced locations for tie downs to the surface
being cut. The guides can be used as:
a. Spaced units confining the HANDICUT base firmly to the wall
being cut.
b. With only one side of the guide acting as a support.
5. Accurate trigger action control. Adjustable stop screw for variable
maximum speeds.
6. Accurate cutting depth is controlled by changing lock position of rear
slotted arm of saw.
7. The Model 20HS HANDICUT features a dual-purpose base plate. It
incorporates excellent stability in hand operation, and for alignment in the
guide sys- tem. The embossed under surface of the base gives extra rigidity
and reduces friction between the base and the cutting surface.
8. Different displacement motors available for different speeds and torques.
Specifications: 1. RATING: 7.2 H.P. Continuous-duty rating @ 2100
psi and 7 gpm.
2. SPEEDS: Continuous variable to maximum ratings.
3. WEIGHT: 27 lbs. (without blade)
4. DIMENSIONS: 23.5” x 7” x 13.5”.
Base dimensions: 22” x 7” x 1”
5. BLADES: Maximum suggested blade size 21”
diameter (cutting depth just under 8”)
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 17
9. Ideal for cutting up to 8” from one side, reinforced concrete walls and
floors as well as brick and block.
Hand Saws
HANDICUT Model 21 Fixed Base Hydraulic Handsaw
This new lightweight handsaw from GDM incorporates the dependability of the popular Handicut handsaw line while simplifying the
frame. The replaceable fixed base eliminates multiple moving parts, decreasing the weight of the saw to 26 lbs. Available with
different motor displacements, ranging in size from 6 GPM to 15 GPM, allowing the saw to adapt to most power units. The Handicut
Model 21 Fixed Base Handsaw is available as a flush cut or combo saw. This versatile lightweight saw offers GDM Handicut
dependability at a competitive price.
HANDICUT Fixed Base Model 21 Combo Hydraulic Handsaw The NEW Model 21 Handicut Handsaw is our most versatile portable unit. Designed for hard to get locations. Combo design allows for flush cut or
standard unit. Use free hand or with guides as a mini wall saw.
Features: 1. Lightweight fixed base eliminates multiple moving parts –
decreases unit weight to 26 lbs.
2. Operates in any position – horizontal, vertical and inverted.
3. Available motor displacements from 7gpm to 15gpm, making it compatible with most power units.
4. Accurate trigger control and adjustable stop screw for variable speeds.
5. The NEW “Cool Hand” handle with dual handgrips for better control.
6. Replaceable fixed base plate assures stability in hand operation.
Specifications: 1. Weight (w/o blade) 26 lbs.
2. Maximum Blade Size 21” diameter
3. Cutting Depth (max): 8.5”
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 18
Hand Saws
HANDICUT Model 14HS Hydraulic Hand Saw
The HANDICUT 14HS Hydraulic Hand Saw is a power-packed portable unit. Designed for those hard to get to jobs, it cuts in any
position and is lightweight for easy operation. Using GDM Guide units, the operator can obtain control, accuracy and cutting depth.
The HANDICUT hand saw is a versatile tool for the small jobs.
Features: 1. HANDICUT Model 14HS is a power packed multi-purpose portable
unit which operates freehand without saw guides or operates as a mini
wall saw with guides.
2. Operates in any position - horizontal, vertical, upside down. Cuts
close to perpendicular structures on any wall, ceiling or floor.
3. Quick opening hinge on the base plate allows the tool guard to be
opened 90 degrees for blade access and easy installation of large
diameter blades on or off the saw guides.
4. The guides are a simple, versatile, inter-connecting design consisting
of two 4’ lengths of angle with spaced locations for tie downs to the
surface being cut. The guides can be used as:
a) Spaced units confining the HANDICUT base firmly to the wall
being cut.
a. With only one side of the guide acting as a support.
5. Accurate trigger action control. Adjustable stop screw for variable
maximum speeds.
6. Accurate cutting depth is controlled by changing lock position of rear
slotted arm of saw.
7. The Model 14HS HANDICUT features a dual-purpose base plate. It
incorporates excellent stability in hand operation, and for alignment
in the guide system. The embossed under surface of the base gives
extra rigidity and reduces friction between the base and the cutting
surface.
8. Different displacement motors available for different speeds and
torques.
Specifications: 6. RATING: 7.2 H.P. Continuous-duty rating @ 2100
psi and 7 gpm.
7. SPEEDS: Continuous variable to maximum ratings.
8. WEIGHT: 21.5 lbs. (without blade)
9. DIMENSIONS: 19.5” x 7” x 10.5”.
Base dimensions: 16” x 7” x .5”
10. BLADES: Maximum suggested blade size 15”
diameter (cutting depth just over 5”)
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 19
9. Ideal for cutting reinforced concrete walls and floors as well as brick
and block.
Accessories - Hand Saws
Professional Grade Hand Saw Blades Custom designed for GDM HANDICUT Saws
Blade Name Size
Model 14H Hand Saw blade with 1 inch arbor 14 X 125 X 1
Model 20H Hand Saw blade with 1 inch arbor 20 X 125 X 1
Model 20H Hand Saw blade with 1 inch arbor 21 X 125 X 1
Model 24H Hand Saw blade with 1 inch arbor 24 X 125 X 1
Custom blades available. Contact GDM for pricing and availability.
HANDICUT Blade Hubs & Caps A. (1408) HANDICUT standard blade hub with 1” arbor 3/8” long to take one to three
B. blades or spacers.
C. (1455) HANDICUT standard blade cap with counter bore to adjust to one to three
D. blades or spacers.
E. (1458A) HANDICUT Special hub with spacer & cap for 1/2” wide cuts.
F. (1459A) HANDICUT Special blade hub extension with spacers & cap for 1” wide
G. cuts. Blade shroud and base MUST be modified to fit. Special water jet is required.
H. (2460) HANDICUT special flush cut Hub. Uses 1-3/8” 3-bolt GDM pattern (requires
I. modified hand saw base, special waterjet and sawblade with 1-3/8” 3-bolt pattern).
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 20
Drilling Motors & Systems
Modular Designed Drilling System Roller Carriages and Coredrill Stands New from GDM Technologies CORCUT Drilling Systems:
TDI BIG CAT 500 Roller Carriage
The system designed for really BIG HOLES Key Features:
• 2 to 1 Gear Reduction Pinion
• Strong Stainless Steel Handles
• 20 Greaseless, Strong Graphite Rollers
• Stronger 4” x 6” Carriage Frame
• Heavy 3” x 5” x 0.250 Precision Ground Column
• Stable 14” x 19” Large Cast Base
Key Benefits: • Bigger Bits Better Control
• Deeper Holes
• Two times stronger than our 300 Carriages.
• Four times stronger than Cast Carriages.
Specifications: • Carriage Frame 4” x 6”
• Cast Aluminum Base 14” x 19”
• Precision Ground Posts 3” x 5” x 0.25”
• Up to 10’ Long
• 20 Easy Rolling Graphite Rollers
• 2 to 1 Gear Pinion Reduction
• 4 Bolt and Key Mount Drill Pad
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 21
Graphite Rollers
Removable 4-Spoke
Stainless Steel
Handle
Fits all Standard 2-1/2 or 3 inch posts
Drilling Motors & Systems
Modular Designed Drilling System Roller Carriages and Coredrill Stands NEW FROM GDM TECHNOLOGIES
CORCUT 250 & 300 Roller Carriages
Roller Carriage Features: • Hard anodized aluminum body
• Stainless Steel shafts and screws
• Greaseless Graphite rollers
• 50% Stronger than cast carriages
• Billet Machined Components
• Adjustable Rollers
• 30% lighter than cast carriages
• Left or right side handle • • Fits 2-1/2” or 3” posts
•
CORECUT 300
Drilling System As pictured:
• 300 small Base
• 3” x 42” Post
• 300 Stealth Roller Carriage
• 2-speed 400-cycle core drill head
• 2-1/2” carriage spacer block
(enabling up to 16” diameter
core bits)
CORECUT 250
Drilling System As pictured:
• 250 small base with
vacuum hold-down
system
• 2-1/2” x 42” Post
• 250 Stealth Roller Carriage
• Milwaukee 2-speed core drill head
• Ampmeter switch box
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 22
Drilling Motors & Systems
Modular Designed Drilling System GDM has a wide variety of posts and bases GDM posts are ground and hard-chromed. Specifications: • Bolt on gear rack
• 1-1/4” 7 threaded for a jack screw
GDM makes anchor bases in three sizes 1. Cast aluminum 7” x 10” for CORCUT 200 and 250 series posts
2. Cast aluminum 7” x 12” for CORCUT 300 series posts
3. Large cast aluminum 14” x 19” for all CORCUT series posts
GDM uniquely engineered hold-down system firmly holds anchor base drilling system to hard surface.
Pictured:
• CORCUT 200 Small anchor base, 36” post
• CORCUT 250 Small anchor base, 42” post
• CORCUT 300 Small anchor base, 48” post
• CORCUT 400 Large anchor base, 72” post
Features: 1. 12 x 18” vacuum plate
2. 1/3 hp Gast vacuum pump
3. Diamond plate pump bracket
4. Suction jar with quick release valve
5. Anchoring bolt and washers
6. 10 inch pneumatic wheels
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 23
Drilling Motors & Systems
Modular Designed Drilling System
Interchangeability of frames and drill heads, carriages and frames, posts and bases is the foundation of this thoughtfully engineered
equipment. The GDM drilling system includes three roller carriages and a hinged motor carriage for a fast and efficient methods of
mounting and demounting drillheads. Choose from our several different drillheads with hydraulic, pneumatic or electric motors.
*Drill Heads Include: motor, standard core drill spindle, water swivel, plumbing, controls and a mounting adaptor to fit drill carriages.
Universal Electric Motors
a. The motors are fitted with an adaptor so each motor can be mounted or dismounted
quickly and easily to the carriage with four bolts. Allows for convenient
interchangeability of different motors at the work site.
b. Several universal motors at different speeds and ratings can be obtained with either 120 or 240 volts.
General Purpose Drilling – Small to Medium Size 2-Speed Milwaukee Electric Motor, Adaptor & Controls 1. HORSE POWER: 3-1/4 H.P
2. SPEEDS: Different Ratios from 300 to 1200 RPM
3. MAXIMUM BIT SIZE: 12” Diameter
4. WEIGHT: 28 lbs.
5. DIMENSIONS: 20” long x 7” wide x 7” deep
6. CONTROLS: Mounted on Carriage
4-Speed Electric Motor, Adaptor & Controls
1. HORSE POWER: 3.5 H.P
2. SPEEDS: 150/450/650/1400 RPM
3. MAXIMUM BIT SIZE: 12” Diameter
4. WEIGHT: 34 lbs.
5. DIMENSIONS: 22” long x 7” wide x 8” deep
6. CONTROLS: Mounted on Carriage
Hi Cycle Motors
2-Speed 400-Cycle Electric Motor & Adaptor
Specifications:
1. HORSE POWER: 7.5 H.P
2. SPEEDS: DIFFERENT RATIOS FROM 150 TO
1200 RPM
3. MAXIMUM BIT SIZE: 18”
4. WEIGHT: 30 lbs.
5. DIMENSIONS: 19” long x 7” wide x 7” deep
6. CONTROLS: Mounted on Switchbox
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 24
Drilling Motors & Systems
Modular Designed Drilling System
300-Series Hydraulic
CORCUT Drillhead
General Purpose/Production Drilling Small to Medium Large Size Bits
1. HORSE POWER 5 H.P to 40 H.P
2. SPEEDS: Variable from 350 to 3000 RPM
3. MAXIMUM BIT SIZE: 36” Diameter
4. WEIGHT- 48 lbs.
5. DIMENSIONS: 16” long x 10” wide x 9” deep
300/2 Series
CORCUT Drillhead
Two motors in one. This double displacement hydraulic motor is designed to
operate with high torque/low speed range, or high speed/low torque range
depending on the bit diameters. The GDM flow control can adjust speed in
either range. With this drill head you can use a wider range of bit diameters with
the maximum use of power available without the use of a gearbox. Seven
different displacement drill heads are available. Shown is our new GDM 300-
Series.
Pneumatic Motors
Air Motors:
• Safe and clean with good performance characteristics for
core drilling.
Deep Holes/Production Drilling
Small to Medium Size Bits
9-Series:
1. HORSE POWER: 9 H.P
2. SPEEDS: 1100 RPM Load Speed
3. MAXIMUM BIT SIZE: 8” Diameter
4. WEIGHT: 40 lbs.
5. DIMENSIONS: 16” long x 10” wide x 12” deep
400-Series CORCUT Drillhead
Heavy Drilling Very Large Size Bits
1. HORSE POWER: 30 H.P to 40 H.P
2. SPEEDS: Variable from 50 to 500 RPM
3. MAXIMUM BIT SIZE: 60” Diameter
4. WEIGHT: 71 lbs.
5. DIMENSIONS:
20” long x 12” wide x 7” deep
Manufacturers of Concrete Sawing & Drilling Equipment GDM Technologies 1910 South Fremont Drive, Salt Lake City, UT 84104 -Toll Free 866-4GDMSAW (866-443-6729) Fax (801) 977-0056 [email protected]
As of 3/01/17 prices and specifications subject to change without notice - Revision 2017.03.01
Page - 25
Drilling Motors & Systems
Modular Designed Drilling System
CORCUT 200
Features: 1. Modular Components:
a. Total interchangeability of drill heads, motors,
carriages, columns, and bases.
b. Gives a greater versatility of the product with a lower
investment in complete drill units.
2. Hinged Carriage:
a. Allows the motor and carriage to be
mounted at any convenient height on
the post.
b. The base and column can be mounted to
the wall or floor independent of the
carriage thereby avoiding handling a heavier, more
cumbersome unit.
c. Permits easier set-up in confined spaces.
d. One piece drive gear spindle with hex on both ends.
3. Designed to operate from left or right hand sides or both
sides alternating to drive in drill bit. Operates with the
GDM four bar handle or standard 5/8” socket & ratchet.
4. Adjustable Wear Plates:
a. The carriage-to-column wear plates can be adjusted
with standard shim stock to fit the needs of the driller
or compensate for wear.
b. The wear plates are captive on the carriage with
screws and can he replaced as needed.
5. Large Base with Removable A-Frame:
a. The A-Frame adds to the strength and rigidity of the
2” column, yet can he quickly removed in one piece
by removing only one bolt. Standard column height is
36”. 42” columns are also available. Sturdy base with
two wheels is attached to rear of plate for mobility.
b. Two-piece compact unit for confined areas. Easily
mounted on walls.
c. Sturdy base with 2” column. Standard column height
is 36”. Other lengths are available.
UNIVERSAL WALCUT TRACK
(CORCUT)
Thoughtfully engineered and modularly designed
to complement GDM tracks. “The trick is in the
track” takes on new meaning with this tracking
plate. Use this in conjunction with our
WALCUT Tracks, any GDMCORCUT drill, or
with a number of different tools, such as our
HANDICUT Saw for precision movement back
and forth. This carriage gives you the edge in
line drilling, cutting or breaking with reduced
set-up time.
New! RMT 250
Thoughtfully engineered and modularly designed to complement
GDM tracks. “The trick is in the track” takes on new meaning
with this tracking plate. Use this in conjunction with our
WALCUT Tracks, any GDM CORCUT drill, or with a number
of different tools, such as our HANDICUT Saw for precision
movement back and forth. This carriage gives you the edge in
line drilling, cutting or breaking with reduced set-up time.
CORCUT Accessories
GDM has a full line of coredrilling accessories:
• Pictured: Heavy-duty box pin adaptor, 1-1/4”-7 and 5/8”-11
extensions, Shaft adaptors, Speed nuts, anti-sieze washers,
etc.