請仔細閱讀並妥善保存此說明書

Instruction and installation manual

Please read and save these instruction

2

Introduction

Read this manual carefully as it offers practical advice to help you get the most from your washing machine. This «Instruction and Installation Manual» contains everything you need to know about the everyday running of your machine. Please refer to this manual for installation and maintenance instructions. The manual also contains information about possible working problems, advice about sorting clothes for washing, an explanation of label symbols and hints about how to remove stubborn stains. 1.- CONTROL PANEL 2.- LID 3.- DRUM 4.- DETERGENT DISPENSER 5.- PLINTH PANEL 6.- FILTER

Table of contents

page

Safety measures 3 Setting up - Installation 5 Preparing the wash. Opening/ closing the drum 7 Detergent load 8 Electronically-controlled variable load- Fuzzy Logic 8 Description of controls 9 Special programmes 13 General recommendations 14 Troubleshooting 16 Washing hints 17

Safety measures

This appliance meets the European Directives 2004/108/EC, 2006/95/EC which have been substituted respectively by 89/336/EEC, 73/23/EEC and subsequent modifications thereof.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

ATTENTION: FOR ALL CLEANING AND MAINTENANCE WORK

• Remove the plug.

• Turn off the water inlet tap after each wash. 3

• The manufacturer fits all the machines with an earth connection.

Ensure that the electrical installation has an earth connection and that it is connected; if not, call a qualified Service Center.

The earth connection is essential for user safety as it elimi-nates the risk of electrical discharge.

• Power sockets should be in easily accessible places so that the washing machine can be unplugged in case of any problems.

• If the electric cable is damaged replace with an original set (cable and plug) supplied by the manufacturer or official after-sales service.

note: In the event that it is necessary to replace the power cable, make sure that you comply with the following colour-code chart during the wiring: blue neutral brown phase Yellow-green earth

The manufacturer accepts no responsibility for any damage to people or things resulting from the failure to comply with the appliance’s installation and safety regulations. • Do not touch the appliance with wet hands or feet.

• Do not use the appliance when bare-footed.

• Use extension cords only with extreme care.

• Do not use adapters or multiple plugs.

• Do not allow the appliance to be used by children or the infirm without due supervision.

• Do not pull on the power cord or the appliance itself to remove the plug from the socket.

• Do not leave the appliance outdoors or exposed to the atmospheric elements (rain, sun, etc.).

• Do not cover the appliance with cloth or plastic while it is working.

• Do not install the appliance in damp places or anywhere where it could be sprayed by the shower.

• Do not install the appliance on a surface which obstructs the space between the floor and the base of the machine.

• Keep all packaging out of the reach of children as it could constitute a health hazard.

ATTENTION: DURING A WASH CYCLE THE WATER CAN REACH TEMPERATURES OF 90ºC.

4

Setting up - Installation

• Unpack the appliance.

• Remove the 4 screws (A) from both clamps and the 4

screws (B).

• Replace the 4 screws (A) and fit the trims provided (D).

If your model offers this function: Position the protection sheet as shown in the diagram. 1.- Washing machine with wheel trolley. 2.- Washing machine without wheel trolley.

ATTENTION: DO NOT TURN THE TAP ON • The washing machine should be connected to the water mains via the new tube supplied with the appliance (inside the drum). Do not use the old tube for this purpose. • Connect one end of the water inlet pipe with the elbow bend to the electrovalve (top rear part of the machine) and the other end to a tap or a plumbed-in 3/4" gas threaded connection. • Place the washing machine close to the wall, ensuring that there are no bends or kinks anywhere in the tube. Hook the outlet pipe to the edge of the sink or preferably to a fixed drainage outlet of a diameter greater than that of the outlet pipe and at a height of min. 50 cm. and a maximum of 75 cm. from the floor. If necessary, use the curved accessory to attach and support the outlet pipe more securely.

5

If your model offers this function: • To move the washing machine easily, turn the trolley lever to the right. Once you have finished moving the machine, return the lever to its original position. • Level the machine by adjusting the front feet. a) Turn the nut clockwise to release the screw on the foot. b) Raise or lower the foot by rotating it until it stands firmly on the floor. c) Lock the foot in position by turning the nut anticlockwise until it comes up against the bottom of the washing machine. Check that the appliance is properly levelled. Check that the washing machine does not rock by trying to move two diagonally opposite top corners at the same time. • If you move the washing machine from one place to another, you must level the feet again afterwards. • Connect the machine.

6

Preparing the wash. Opening/ closing the drum

ATTENTION: IT IS IMPORTANT TO MAKE SURE THAT THE DRUM IS CAREFULLY OPENED AND CLOSED, OTHERWISE THE MACHINE OR LAUNDRY COULD GET DAMAGED. ENSURE THAT THE DOORS FIT TOGETHER PERFECTLY AND ARE PROPERLY CLOSED. Loading 1. Open the washing machine lid.

2. Open the drum by pressing the (A) button with one hand while pressing down on the opposite door with the other.

3. Place clothes in the drum one item at a time, and without squashing. Do not exceed the load limits recommended in the “programme table”. An overloaded washing machine will not wash properly, and will leave clothing wrinkled. 4. To close the drum, place the doors so that the one with the (A) button is below the other and they fit together perfectly.

Detergent load

II I Maximum Main wash washing powder Maximum Main wash washing liquid

Maximum pre-wash washing powder

recommended

Maximum scenting agent

The detergent dispenser is divided into 3 compartments: .- Compartment I is for the pre-wash detergent. .- Compartment II is for the main wash detergent. .- The compartment is for fabric conditioners, scenting agents and special additives such as starch, blueing, etc. The detergent dispenser has two reference marks: .- Recommended (lower reference mark). This indicates the recommended level for the pre-wash and main wash compartments. .- Max. This indicates the maximum level, which should never be exceeded. Important: - Do not use liquid detergent for programs with a prewash cycle and/or timed start. - When the clothes present stains that need treatment with bleaches liquids products, you can proceed to their preliminary cleaning in the washing machine. For that: Introduce the bleach product in the "compartment II", and set the rinse program . Once finished set the programmer to the OFF position, add the rest of the laundry, and proceed with a normal was program.

Electronically- controlled Variable Load – Fuzzy Logic

This machine has electronics that automatically process all stages of the wash to ensure exceptional results and at the same time save you time and money. Once a programme has been selected, the machine optimises the following elements depending on the wash load and type of fabric: - quantity of water and power consumption - wash time - rinse efficiency The washing machine also: - detects suds and increases the amount of rinse water if necessary - adjusts spin speed according to load distribution, thus forestalling any imbalance in the mechanism.

8

Description of controls

V

A PROGRAMME SELECTOR Use this control to select the desired wash programme. Turn the selector (it can be turned in both directions) so that the programme is opposite the reference indicator (p). The temperature selected will depend on the programme. (See the Programme Table).

B1 SPIN/NO SPIN SELECTOR B2 DELAYED START KEY C1 COLD WASH C2 AQUA (SENSITIVE KEY) G DOOR LOCK LAMP H START/PAUSE KEY V “DIGITAL” Display

The display’s indicator system allows you to be constantly informed about the status of the machine

p CONTROL POSITION INDICATOR

9

A

p

C1

H B2 G B1 C2

+

Programme table mod PTL 6105

programme programme for

aprox. time min.

max. temp.

setting ºC

spin

speed rpm/min

max. load Kg.

washing powder load

option keys C

I II Cold +

Aqua

COTTONS

�� � � � � * Fast coloureds 6 � � � � * Fast coloureds 6 � � � � Delicate coloureds 6 � � � �

MIXED

SYNTHETICS

Fast coloureds � � � � Delicate coloureds 3 � � � � Delicate coloureds 3 � � � �

DELICATES Wool � � � Hand wash � � �

SPECIAL

Rinse display � � Spin display Drain display

-

display � � �

Rapid 44 display � � � Rapid 30 display � � �

* Programme as per EN 60456

Technical data mod. PTL 6105

Mains voltage

Wash power rating

Spin Power rating

Pump Motor Power rating

Heating element power rating

Max. Power input

Mains Fuse Amp. rating

Water pressure

Water consumption

*prog. EN60456

Energy consumption

*prog. EN60456

220-230V. 50Hz. 175 W. 340 W. 30 W. 1300 W. 1500 W. 10 A. 0,05-0,8 Mpa 49 L.

IMPORTANT: Do not use liquid detergent for programs with a prewash cycle and/or time delay. PREPARING THE WASH CYCLE 1.- Once the washing is loaded, ensure that the drum doors are properly closed.. 2.- Add detergent and additives, not exceeding the maximum level indicator. .- detergent for pre-wash I .- detergent for wash programme II .- fabric conditioner

Fast coloureds with prewash display 90° 1000 6display 60° 1000display 40° 1000display 30° 1000

1000

620° 800

display 50° 800 3display 40°display 30°

800 800

11

display 30°display 40°

600 600

800

3 40° 800230° 800

0,732 Kw.

-- -

-

--

Eco 20° �

SELECTING THE DESIRED PROGRAMMES AND OPTIONS 3.- Turn the programme selector (A) to the desired programme. 4.- Press the key or keys for any options desired (C1, C2 ). .- It is advisable to select the required options before pressing the Programme Start key (H). .- Remember that if the programme has already passed the stage at which an option is activated, that option will not be implemented. C1 Cold wash key By pressing this button it is possible to transform every programme into a cold washing one, without modify other characteristics (water level, times, rythmes, etc..). Curtains, small carpets, man made delicate fabrics, non coulor fast garments can be safely washed thanks to this new device. C2 Aqua (sensitive key) Thanks to the new SENSOR ACTIVA SYSTEM, by pressing the key it is possible to run a special washing cycle applicable to all programs and types of fabric, caring for their fibres and the delicate skin of the users who use them. Taking on much more water, together with the new combined action of drum rotation cycles and taking on and discharging water allow you to obtain perfectly clean, rinsed clothes. More water is used in the wash to dissolve the detergent completely, ensuring an effective washing action. The water in the rinses has also been increased to eliminate all trace of detergent in the fibres. This function has been specifically studied for people with delicate, sensitive skin, who can suffer irritation or allergy from the slightest detergent residue. It is also advisable to use this function for children's clothes and delicate fabrics in general, especially for washing bathrobes, whose fibres tend to retain detergent. This option is not available for the wool program. 5.- Select spin speed if required (B1) B1 spin speed Once the programme has been selected, the maximum spin speed allowed for that programme appears on the display. Pressing the spin button will reduce the speed by 100 rpm each time the button is pressed. The minimum speed allowed is 400 rpm, or it is possible to omit the spin by pressing the spin button repeatedly. 6.- To start the programme, once options have been chosen, press the key H. The washing machine will begin to operate. If you wish to cancel the option you have selected, press the key again. (The pilot light will go off). B2 Time delay button This button allows you to pre-programme the wash cycle to delay the start of the cycle for up to 24 hours. To delay the start use the following procedure: Set the required programme. Press the button once to activate it (h00 appears on the display) and then press it again to set a 1 hour delay (h01 appears on the display); the pre-set delay increases by 1 hour each time the button is pressed, until h24 appears on the display, at which point pressing the button again will reset the delay start to zero. Confirm by pressing the “START/PAUSE” button (the light on the display starts to flash). The countdown will begin and when it has finished the programme will start automatically. It is possible to cancel the delay start by taking the following action: Press and hold the button for 5 seconds until the display will show the settings for the programme selected. At this stage it is possible to start the programme previously selected by pressing the “START/PAUSE” button or to cancel the process by setting the selector to the OFF position and then selecting another programme. Cycle duration (V) When a programme is selected the display automatically shows the cycle duration, which can vary, depending on the options selected. Once the programme has started you will be kept informed constantly of the time remaining to the end of the wash.

11

Door lock light (G) Once the START/PAUSE button has been pressed the light first flashes then stops flashing and remains on until the end of the wash. 2 minutes after the end of the wash the light goes off to show that the door can now be opened. Cancel-change programs Once you have started a program, and wish to change or cancel it, you should proceed in the following manner, - Put the program selector in the OFF position. At that instant, you have cancelled the program and can if you wish to do so, select a new one. - Select the new program. - Click the key (H) again.

The washing machine will perform the new selected program. Programme pause It is possible to momentarily stop the wash programme so that more washing can be added, and to do so, proceed as follows: - Hold down the (H) key until the option key lamps begin to flash and the time remaining indicator display,

and pilot lamp lights up. - When the Door Lock lamp goes out (after approx. 2 minutes), open the door and add the desired

washing. - Correctly close the doors of the drum and the outer cover. - Press the key H, and the washing machine will continue with the programme. When the programme has been completed, the message "END" will appear in the indicator display, Wait until the Door Lock lamp (G) goes out (after approx. 2 minutes) “To remove the washing, set the programme selector to the OFF position”, before opening the washing-machine lid and the drum doors.

12

Eco 20°This innovative programme,allows you to wash different fabrics and coloursEco 20°:

together,such as cottons,synthetics and mixed fabrics at only 20 and provides anºC excellent cleaning performance.Consumption on this program is about 40% of a

conventional 40 cottons wash.ºC

General recommendations

CLEANING AND MAINTENANCE OF THE MACHINE Do not use abrasives, spirits or solvents when cleaning the exterior of the washing machine. It is sufficient to use a damp cloth. The washing machine requires very little maintenance. • Drying the rubber seal of the drum. • Cleaning the dispenser and its compartments. • Cleaning the filter. • Cleaning prior to removals or when the machine is to stand idle for long periods. To help conserve the washing machine, dry the rubber seal and leave the door open when the cycle ends. CLEANING THE FILTER The washing machine comes with a special filter, located behind the machine’s front plinth panel, that collects larger objects (coins, buttons, etc.) which could even block the pump. It is advisable to clean the filter whenever the machine fails to rinse the clothes as well as it should or when it fails to drain properly.

When it is necessary to clean the filter, proceed as follows:

• Use a basin to collect the water coming out. • Remove the filter and clean it. • Once the filter is clean, replace it by following the above- mentioned pro in reverse.

14

CLEANING THE DETERGENT DISPENSER AND ITS COMPARTMENTS

A

II I

S

B

C

.- It is advisable to clean the three compartments of the detergent dispenser (pre-wash, wash, and fabric conditioner) from time to time. To do this, remove the detergent dispenser and after cleaning it, fit it back in place. To remove and fit the detergent dispenser, follow the steps indicated in the images. removing .- Press button A .-Hold down the button and pull the detergent dispenser outwards .- Remove the dispenser and clean it .- In the case of the pre-wash (I) and wash (II) compartments, it is advisable to remove any dried-in remains of detergent which obstruct the flow of the detergent to the drum. .- In the fabric conditioner compartment, the trap (S) located at the rear part of the dispenser should be removed by pulling them out. Remove any solid residue which could block the holes in the compartments. fitting .- Fit in the tabs as shown .- Push the detergent dispenser towards the housing (C) in the door until the tab clicks into place.

15

Troubleshooting

FAULT CAUSE SOLUTION 1.- No programme works • The appliance is not plugged

in. • The general switch is discon- nected. • There is no electricity. • The fuses in the electric insta- llation are damaged. • The door is open.

• Plug it in. • Activate the general switch. • Check. • Check. • Close the door.

2.- The appliance does not load water

• See causes for 1. • The tap is turned off.

• Check. • Turn on the tap.

3.- The water does not drain • The filter is clogged. • The outlet pipe is bent.

• Check the filter. • Straighten the outlet pipe.

4.- The spin function does not work

• The washing machine has not yet drained the water. • The “Spin Exclusion” option is activated.

• Wait a few minutes for the was- hing machine to drain. • Enable the spin option.

5.- Strong vibrations during spin cycle

• The washing machine is not correctly levelled. • The anchoring device for trans- port has not been removed. • The wash load is not evenly distributed.

• Adjust the feet. • Remove the transport support. • Distribute it evenly.

6.- The high-speed spin does not work

• The wash load is not evenly distributed within the drum.

• Distribute the wash load evenly in the drum.

7.- Display will show error nº 0,1,5,6,7,8,9,12,13,15,16

• Contact technical service.

8.- Display will show error nº 2

• Machine does not fill with water • Check that water inlet tap is open. 9.- Display will show error nº 3

• Water does not empty from machine

• Check that outlet is not clogged • Check for kinks in outlet tube.

10.-Display will show error nº 4

• Too much water in machine. • Shut off water tap. • Contact technical service

If the problem or malfunctioning persists, disconnect the machine, turn off the tap and do not try to repair. For all repairs contact an Official Technical Assistance centre (consult the European guarantee sheet) and always insist on the use of original parts. Failure to do so may compromise the safety of your machine. When contacting a Technical Assistance Centre always refer to the model (see also control panel) and the registration and serial numbers indicated on the plate at the bottom front of the machine behind the plinth panel or on the guarantee certificate. That is to say, everything that appears in the box. Providing this information will ensure a faster and more efficient service.

16

Washing hints

Hints on the most economical, most environmentally friendly way to use your washing machine. HINTS ON USING YOUR WASHING MACHINE Wait until you have a full load before using the machine: this will avoid the use of more water and power than necessary. We recommend using the full load capacity: this could save you up to 50% in power consumption. Wash a single full load rather than two light loads. WHEN IS PRE-WASHING NECESSARY? Only when washing heavily soiled clothes. With clothes that are not especially dirty, you can save between 5 and 15% by not using this option. WHAT WASH TEMPERATURE SHOULD I USE? Applying a stain remover before placing clothes in the machine will eliminate the need for wash temperatures of more than 60 ºC.

When loading a wash into the drum, we recommend that you: • For specially delicate garments we recommend the use of a protective net. • Empty all pockets and ensure that they do not contain metal objects (paperclips, safety pins, pins, coins,etc.). • Fasten pillow slips, close all zips and fastenings, and tie any loose ribbons or belts from dresses. • Remove all runners (metal and plastic) from curtains and net curtains. We recommend that the ribbon be gathered into a ball and tied with its own cord. • Unfold all items to be washed. • Be careful not to exceed the recommended load for each programme. • When washing rugs, bedspreads and other highly absorbent items, cancel the spin option. • In order to be able to wash woollens in the washing machine they must carry the “Pure New Wool” symbol as well as the information “does not become matted” or “machine washable”. • If possible, do not wash only towels. Mix them with your regular washing. • Ensure that no item becomes trapped between the drum doors.

LABEL SYMBOLS

Labels are usually sown into the collar or side seams. The symbols which appear on them indicate the following: • Maximum WASH temperature. • Appropriate and inappropriate washing methods. • Appropriate and inappropriate washing products.

The symbols are as follows:

WASH

Washing instructions always appear as a basin with different indications: • Do not wash. • Can be washed both by hand or in the washing machine. The figures in the basin indicate the

maximum wash temperature. • Hand wash only.

When the hand is half submerged in the water, this means that the item should be tumbled only gently during washing. If it is fully submerged in the water, this means that the garment should only be washed by hand.

• The line under the basin means that the item should be washed on a gentle cycle. • Do not spin.

BLEACH Bleach is widely used to whiten fabrics, although in some cases it can cause irreparable damage. There are various symbols which refer to its use.

• Bleach can be used. • Do not use bleach.

17

Please record the following information:

� Model

� Serial No.

� Name of distributor

� Date of purchase

The manufacturer reserves the right to make any technical modifications due to product improvement. No prior notice will be given.If you have any enquiry,please contact our after-sales department and forgive for any inconvenient. All information is subjected to English version.

/F, Shing Dao Industrial Building, 232 Aberdeen Main Road,Hong Kong

: 8210 8210 Service Hotline : 8210 8210

18

�

�

�

�

232 /F, Shing Dao Industrial Building, 232 Aberdeen Main Road,Hong Kong

: 8210 8210 Service Hotline : 8210 8210

19

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). ���������������� ����������������������������������������������������������������properly all pollutants, and recover and recycle all materials. Individuals can play an important role in ensuring that WEEE does not become an environmental issue; it is essential to follow some basic rules:- WEEE should not be treated as household waste;- WEEE should be handed over to the relevant collection points managed by the municipality or by registered companies. In many countries, for large WEEE, home collection could be present. In many countries, when you buy a new appliance, the old one may be returned to the retailer who has to collect it free of charge on a one-to-one basis, as long as the equipment is of equiva-lent type and has the same functions as the supplied equipment.

簡介

請仔細閱讀本手冊，因為它提供了實用

建議，幫助你認識你的洗衣機。

這《操作指南與安裝手冊》已包括洗衣

機的日常運行操作。

請參閱本手冊的安裝和保養說明。該手

冊還包含有關可能的工作問題，建議對

清理衣服洗滌，解釋和提示符號的標籤

如何去除頑固污漬。

1 .- 控制板面

2 .- 機蓋

3 .- 滾桶

4 .- 洗衣劑抽屜

5 .- 底板

5 .- 過濾網

安全的措施

設置 - 安裝

準備清洗衣物。打開 / 關閉滾桶

放入洗衣劑

電子裝置 - 控制不同洗衣量 - 快思邏輯

面板詳述

特別程式

一般建議

排除疑難

清洗貼士

2

4

6

7

7

8

12

13

15

16

安全措施

內容

2

3

‧製造商所有的機器符合與地線連接。

確保用電的安裝有連接地線 ; 如不是，請召喚一個合規格

的服務中心。

連接地線對使用者安全是有需要的 , 因為此可減少漏電的

風險。

‧電插座應設置在洗衣機容易 接的地方，萬一有任何問

題可即時拔除。

‧如果電線損壞更換要由製造商或官方售後服務所提供原

本的一套（電線和插頭）。

備註 :

當發生事故需要更換電線期間，請確保遵從以下顏色代碼

圖連接 :

藍色 中線

啡色 火線

黃綠色 地線

製造商概不負責未能遵守該設備的安裝和安全規則所造

成人或事物的任何損害。

‧濕手或腳請不要觸摸電器。

‧請不要赤腳使用洗衣機。

‧請小心使用延長線。

‧不要使用連接器或多個插頭。

‧不要讓兒童或體弱者在缺乏應有的監督下使用。

‧不要拉扯電源線或洗衣機本身，以從插座移除插頭。

‧不要遺棄洗衣機在戶外或暴露於大氣成分（雨，太陽，

等等）。

‧當洗衣機正在運行中，不要用布或塑膠覆蓋著。

‧不要安裝本產品在潮濕的地方或任何可能淋浴噴灑到

的地方。

‧不要安裝洗衣機在表面上會妨礙地面之間的空間及機

器的底部。

‧保留所有包裝遠離兒童觸摸到的地方，因為它可能構

成危害健康。

警告 : 在清洗程式中 , 水溫可達 90℃

設置 - 安裝

重要 : 在這時不要開啟水龍頭。

‧洗衣機應用機器 ( 內桶 ) 所提供新的膠管接駁到水

源。不要使用舊膠管接駁。

‧使用肘部曲頭，連接水管一端至電磁閥（洗衣機頂

部後方），另一端連接水龍頭或直徑 3 / 4“螺紋連接

頭。

‧把洗衣機安裝在牆邊。掛起去水管至浴盆邊，小心

不要屈曲或擠壓水管。最好接駁排水管至直徑比排水

管大的固定出水口，而高度離地面至少 50 厘米，最

高 75 厘米。

如果需要，使用弧形附加配件更穩固地支撐去水管。

如果你的型號提供了此功能：

放置保護片於圖中所示。

1 .- 洗衣機有滑輪手推車。

2 .- 洗衣機沒有滑輪手推車。

‧除去包裝 ‧由螺絲夾移除 4 個螺絲

(A) 及 4 個螺絲 (B)。

‧更換 4 個螺絲 (A) 和安

放所提供的裝飾 (D)。

4

如你的型號提供此功能；

‧要移動洗衣機很容易，打開手推車槓桿到右面。一

旦你完成了移動的，把槓桿推回到原來的位置。

‧使用洗衣機的前機腳調較水平。

a) 順時針轉動螺絲帽鬆開機腳螺絲。

b) 旋轉機腳升高或降低，直至它平穩安放在地面上。

c) 逆時針方向轉動螺絲帽鎖定機腳位置，直到它碰上

了洗衣機的底部。

檢查洗衣機是否平穩。

試圖同一時間移動洗衣機頂部斜對面角落，檢查洗衣

機是否移動。

‧如果您將洗衣機從一個地方移到另一個地方，你必

須再次調校機腳。

‧連接洗衣機

5

準備洗衣 - 打開 / 關閉滾桶

注意 :

確保小心地打開和關閉滾桶，否則會損壞洗衣機或洗

衣物。

確保機門完全關閉好。

˙ 放入衣物

6

放入洗衣劑

電子裝置 - 控制不同衣量 - 快思邏輯

7

最高量主要洗衣粉

最高量主要洗衣液

最高量預洗洗衣粉

最高量香味劑

建議用量

洗衣劑的儲存格層分為三格：

- 格層 I - 預洗器皿 ( 粉沫 )

- 格層 II - 清洗器皿 ( 粉沫或液體 )

- 格層 - 是織物柔順劑，香味劑和特殊添加劑，如澱粉，藍色漂白劑等。

清洗劑的儲存有兩個參考標記：

- 建議用量（下參考標記）。表示預洗和主清洗的洗衣液建議用量。

- 最高量 這表示了最高水平，絕不應超越。

重要事項：

- 不要使用洗衣液用於一個預洗整個過程和 / 或定時啟動的程式。

- 　　當衣服污漬是目前需用漂白劑液體產品處理，您可以用開洗衣機進行初步的清洗。為

此：介紹了漂白產品中的“格層Ⅱ”　，並設置清洗程式。當完成後程式設置到關閉位置，

加上其餘的洗衣物，並可進行正常程序的清洗。

8

面板詳述面板詳述

A

B1B2C1C2GHV

P

V A

p

C1

H B2 G B1 C2

PTL 610 E

Amp. rating *

EN60456 *

EN60456 220-230V.

50Hz. 175 W. 400 W. 30 W. 1950 W. 2150 W. 10 A. 0,05-0,8 Mpa 49 L.

9

340 1300 1500

程式

棉質

混合合成纖維

纖柔

特別

程式適用於程式適用於

大約最高時間分鐘

最高溫度設定℃

最多洗衣量洗衣量千克

使用衣粉使用衣粉 選項鍵 C選項鍵 C

旋速rpm/ 分鐘rpm/ 分鐘 冷凍

不褪色衣物設洗

* 不褪色衣物 *不褪色衣物

不褪色衣物

纖柔顏色衣物 纖柔顏色衣物

不褪色衣物

纖柔顏色衣物 纖柔顏色衣物

纖柔顏色衣物 纖柔顏色衣物

羊毛 羊毛

手洗 手洗

顯示

顯示

顯示

顯示

顯示

顯示

顯示

顯示

顯示

顯示

顯示

顯示

顯示

顯示

顯示

過水

旋乾

排水

快速 44

快速 30

800800800

1000100010001000

600600

8001000

800800800

0

6 6 6 6

3 3 3

6 3 2

1 1

90°60°40°

40°

40°

40°

30°

30°

30°

30°

50°

20°

0,732 Kw.

10

11

一般建議

清潔過濾網

洗衣機設有特別過濾網隔阻大物件，它位於機器背後的前面板底座，它們會阻塞排水管，如

錢幣，衣鈕等。這樣可容易隔除。

提議最好清潔過濾網當洗衣機未能適當沖洗衣服及它不能正常排出污水。

有需要清潔過濾網時， 過程如下；

用底部作托盤收集過濾網流出的水。

移除和清潔過濾網。

清潔後，重置過濾網以反次序重覆以上步驟。

13

清潔洗衣劑抽屜和格層

I II

S

C

14

15

排除疑難

故障

1. 程式不能開始

2. 不能注水

3. 不能排水

4. 洗衣機周圍有水

5. 旋轉中有強烈震動

6. 沒有旋轉脫水

7. 顯示屏出現錯誤 n?

0,1,5,6,7,8,9,12,13,16

8. 顯示屏出現錯誤 n? 2

9. 顯示屏出現錯誤 n? 3

10. 顯示屏出現錯誤 n? 4

原因● 電源插頭沒有插進插座● 主要電掣沒有開動● 沒有電源● 電路保險絲斷毀● 打開了機門● 參考故障 1● 注水水龍頭關掉● 排水管淤塞了● 排水管屈曲● 洗衣機還沒有排水● “旋轉排斥”選項生效

● 洗衣機沒完全平放● 沒有拆除搬運托架● 衣物分佈不平均● 衣物在滾桶內分佈不平均

● 洗衣機沒有注水● 洗衣機內的水沒有排出

● 洗衣機內太多水

處理● 插回插頭● 開動主要電掣● 檢查● 檢查● 關好機門● 檢查● 開啟注水水龍頭● 檢查過濾網● 伸直排水管 ● 等待數分鐘直至洗衣機排水● 讓旋轉選項生效

● 調較機腳● 拆除搬運托架● 平均分佈衣物● 在滾桶內平均分佈衣物

● 聯絡技術中心

● 檢查入水水龍頭是開著的● 檢查出水處有沒有堵塞● 檢查扭結在出水管● 關掉水龍頭● 聯絡技術中心

清洗貼士

16

30.10.2015/M-43011248