Making Your Own Drinking Horn
-
Upload
gilberto-de-miranda -
Category
Documents
-
view
7 -
download
0
description
Transcript of Making Your Own Drinking Horn
Making your own drinking
horn
By: Baron Vladimir of Esztergom
Process perfected by Master Snaeulf Rolfson, and] Mistress Rosetrude the Shrew, Laurel Atlantia
This process assumes that the horn has already been separated from its
bone core.
1. Finding the horn: Try to find a horn that has relatively few
flaws in it. Keep in mind that no horn is perfect. A lot of work
will have to be done to make even the best raw horns
presentable. Choose colors that will complement the pigment
you will be using later.
2. Clean the horn: The inside of the horn must be cleaned and
sanitized before any work can be done. First, you should
sterilize the inside of the horn with a strong mixture of bleach
and water. Let it soak overnight outside or in a well-ventilated
area. Neutralize the bleach with vinegar. After bleaching DO
NOT USE AMMONIA. Then wash the inside of the horn with
soapy water and a scrubbing wire brush. Be sure you reach all
the way down inside the horn. with course grit paper. Be
careful to remove only the blemishes and not to sand to long in
one spot; you want to retain the natural curved surfaces of the
horn. If you do not have a power sander you will have to sand
by hand. If the blemishes are extreme a file or sharp knife can
be used to cut them away. To remove major blemishes you
may go across the grain of the horn. This will speed the
sanding process. Make certain that the following sanding are
done with fine and then ultra fine grit paper. Final sanding
should be done with an ultra fine flap sander or a polishing
cloth. You do not need to sand the entire surface or the horn;
leave the top portion, which you will later cut away.
3. Cutting the top: Cut the top of the horn off with a fine
toothed saw. A hacksaw will probably suffice, but a band saw
will be preferable. Try to cut the top off as level as possible.
Sand the raw edge smooth with ultra fine grit paper then a
polishing cloth.
4. Cutting the design: Trace or draw the desired design onto the
horn. Remember you are transferring a flat image onto a
curved surface and will have to compensate. Carbon paper will
work well for this.
5. Etch the design: Use a stylus, nail, or a strong pin to scratch
the design into the surface of the horn. A dremel tool or
carving knife can be used for deeper images. Be very careful.
A mistake is best remedied by finding some way to
incorporate it into the overall design rather than trying to sand
it out.
6. Pigmenting the design: Use pigmented wax or water based
ink to fill in the design. Use caution with ink that it does not
flow freely into small cracks and crevices in the surface that
you did not notice before. If ink is used, carefully sand off the
ink remaining on the surface.
7. Wax the outside: Warm the horn so that it will take the wax
more readily. Smear the wax across the surface of the horn.
Beeswax works well for a shiny finish. Shoe polish will also
work if spread very thinly, but it will change the color of the
horn slightly. Buff the horn with a rag to even out the coating.
8. Treat the inside: Again, beeswax can be used. Do not use this
method if you intend to drink hot liquids. Salad bowl finish
can be found at unfinished furniture stores and also works very
well. For those with authenticity concerns, no, it is not period.
But it is made from natural mineral oil and spirits. Hot and
cold liquids of varying strength can be drunk from the horn
then. To use the finish, first heat the horn, and then apply
finish liberally to the inside with a brush or rag. Be sure to
coat the entire interior. Dump out the excess. Hang the horn in
a well-ventilated area with a fan blowing up into the horn for
24 hours. The finish will require 72 hours to cure completely;
then it will be safe to drink from
Este processo assume que o corno já foi separado do seu núcleo de osso.
1. Encontrar o chifre: Tente encontrar um chifre que tem falhas relativamente
poucos nele. Tenha em mente que nenhum chifre é perfeito. Muito trabalho terá
de ser feito para que até mesmo os melhores chifres primas apresentável.
Escolher as cores que irão complementar o pigmento que será utilizado mais
tarde.
2. Limpe o chifre: O interior do chifre devem ser limpos e desinfectados antes
de qualquer trabalho pode ser feito. Primeiro, deve esterilizar o interior do corno
com uma mistura forte de lixívia e água. Deixe de molho durante a noite do
lado de fora ou em uma área bem ventilada. Neutralizar a água sanitária com
vinagre. Após o branqueamento NÃO USE amônia. Em seguida, lavar o interior
do corno com água e sabão e uma escova de arame de lavagem. Certifique-se
de chegar a todo o caminho dentro do chifre. com papel grit claro. Seja
cuidadoso para remover apenas as manchas e não a areia a muito tempo em
um lugar, você quer manter as superfícies naturais curvas do chifre. Se você
não tem uma lixadeira de energia você terá para a areia com a mão. Se as
manchas são extremas um arquivo ou uma faca afiada pode ser usada para
cortá-los fora. Para remover manchas grandes, você pode ir em todo o grão do
chifre. Isto irá acelerar o processo de lixamento. Certifique-se de que a lixa
seguinte é feito com papel de grão fino e ultra fino. Lixamento final deve ser
feito com uma lixadeira aba ultra fino ou um pano de polimento. Você não
precisa de areia toda a superfície ou a buzina; deixar a parte superior, que mais
tarde você vai cortar.
3. Cortando o topo: Corte a parte superior da trompa fora com uma serra de
dentes finos. A serra serão suficientes, mas uma serra de fita será preferível.
Tente cortar o alto fora o mais nivelado possível. Areia à beira-prima lisa com
papel grão ultra fino em seguida, um pano de polimento.
4. Cortar o projeto: Trace ou desenhar o projeto desejado para o chifre.
Lembre-se de que você está transferindo uma imagem plana a uma superfície
curva e terá que compensar. Papel carbono funciona bem para isso.
5. O desenho Etch: Usar uma caneta, unha, ou um pino forte para arranhar o
desenho na superfície da trompa. Uma ferramenta dremel ou faca pode ser
usada para imagens mais profundas. Tenha muito cuidado. Um erro é melhor
remediado por encontrar alguma maneira de incorporá-lo ao projeto global ao
invés de tentar areia para fora.
6. Pigmentação do desenho: Use cera ou tinta pigmentada à base de água
para preencher o desenho. Tenha cuidado com a tinta que não fluir livremente
para pequenas fissuras e fendas na superfície que você não percebeu antes.
Se a tinta é usada, cuidadosamente areia fora a tinta remanescente na
superfície.
7. Encerar o exterior: o chifre do aquecimento para que ele irá tomar a cera
mais facilmente. Esfregaço da cera sobre a superfície do chifre. Cera de abelha
funciona bem para um acabamento brilhante. Sapato polonês também irá
funcionar se espalhar muito mal, mas vai mudar a cor do chifre ligeiramente.
Buff a buzina com um pano, mesmo fora do revestimento.
8. Tratar o interior: Mais uma vez, a cera pode ser utilizada. Não use este
método se você pretende beber líquidos quentes. Acabamento tigela de salada
pode ser encontrado em lojas de móveis inacabados e também funciona muito
bem. Para aqueles com problemas de autenticidade, não, não é período. Mas
ele é feito a partir de óleo mineral natural e de espíritos. Líquidos quentes e
frias de intensidade variável pode ser bebido a partir do chifre de então. Para
usar o acabamento calor, primeiro a buzina, e depois aplicar terminar
liberalmente para o interior com uma escova ou pano. Certifique-se de casaco
todo o interior. Despejar o excesso. Pendure a buzina em uma área bem
ventilada, com um ventilador soprando-se no corno por 24 horas. O
acabamento vai exigir 72 horas para curar completamente, então ele estará
seguro para beber
How to Make a Drinking Horn
Picking and preparation:
When you pick out a horn to use as a drinking horn, there are a couple of things
to look for. First, consider the overall size and shape of the horn. Will you be
hanging it around your neck? Which edge of the rim appears to be shaped
about right for drinking from? And if you do drink from that side, then will the tip
of the horn be pointing up, or down? If it's pointing up, that is better because
your liquid won't tend to "splash" out, but will pour out smoothly. Does the horn
still have a "core" to clean out? This takes a considerable amount of work. How
heavy is it? Will you be holding it in your hand for long periods? How thick is the
actual outer sheath (as opposed to the marrow/core)? If the outer sheath is
thick, then your horn will hold much less liquid than it may appear capable of. In
some horns, the inner "open" area ends not far from the rim, and the whole
middle section to the tip is all solid. If you can... test the horn to see if it will hold
water, without leaking. Leaks can be repaired, but that means more work for
you! You can also get an idea of how much fluid the horn will comfortably hold
this way.
Cleaning:
I like to make my drinking horns, in what I consider the "natural" way. I've read
how some use beeswax, or salad bowl coatings, or some other substance to
coat the inside of the horn, but that seems like a cop-out to me. When I acquire
a horn I usually buy one that is already "cored" and there is no horn-marrow to
clean out. However, if you have a core still in the horn, you may need to boil it
out. Boil the horn, completely submerged in water for at least 6 hours. Gently lift
the horn out, and I like to use a corkscrew to test the rigidity of the core. It
should be very soft and pliable now. Too much boiling, and it should be goop!
You can get large chunks out with the corkscrew, or a pick. If you turn the horn
rim-down, and firmly bang it down onto a table, most of the core should fall out.
If you have a tablespoon you can spare, I'd suggest filing the edges down into a
sharper edge, and use that to pry/scoop out the core. You may need to put the
horn back into the boiling water so that the core further down can be heated,
once you've removed the portion near the rim. If you check your horn every 2
hours you're pretty safe to boil it. The horn will get "mushy" after a while, but as
long as you don't scar the outside with tongs or something, when picking it up,
you can easily re-shape it if it begins to flatten due to all the boiling. Also, I find it
convenient to put something in the very bottom of the pot, so that the horn isn't
directly touching the bottom surface of the pot that you're boiling water in.
Otherwise, the tip of the horn will heat faster than the rest, and this may cause it
to bend, crack or flatten. Be patient getting the core out.. Sometimes, taking the
horn out, and letting it cool down and dry off will reveal that the core can now be
pried out with your spoon/scraper. After the core is out.. you get to start
cleaning the horn! I fill it with boiling water, and wait to see if any leaks develop.
Make a note of the leaks, and we'll repair them later. I get a series of bottle-
brushes and gently, but firmly scrub the inside of the horn, while pouring boiling,
soapy water through between times, to rinse it. The bristle brush is critical... You
have to find a brush that has bristles on the side, and extending out to the top
as well. Otherwise, when you try to shove the brush into the horn, the metal tip
of the brush will possibly scrape furrows on the heat-softened inner wall of the
horn. After go through this process many, many times. I get a horn that is
perfectly clean on the inside!
The Test:
The test of this, is to put pure, bottled drinking water into the horn, and when
your palette is perfectly neutral, sip some of the water, and swish it as if you
were tasting wine. swallow. pour out about half the water, and cover the
opening of the horn, and swish the remaining water around. sip and swish
again. If you have no "horny" taste after this, then you've got a clean horn!
Repair:
If your horn has any leaks, or tears you can use non-toxic finger nail repair glue
(this is a substance used to repair and fortify fingernails, and con be found at
most major stores) to fill in the hole, or rebuild a small portion of missing horn.
Also, if you have "bubbles" or "flakes" of horn material coming loose on the
outside of the horn, these can be repaired in a similiar fashion. For these
problems, it is usually easiest to reboil the horn, until it is very pliable, then
firmly press the bubbles or flakes down until they are as flat against the horn as
they will go. Now if it is a flake, and has an open crack in it, pour the fingernail
repair glue into the crack, and keep forcing it in until the entire crevice is full.
For bubbles, you need to cut away the "bubbled up" portion of the horn skin,
then apply the fingernail repair glue all around the edges of the bubble where
you cut away the raised portion. File down any excess fingernail repair glue,
and using fine grain steel wool, create a sheen close to that of the regular horn
skin. Finish as usual with a jeweler's rouge cloth and your repair spot should be
very close to undetectable. A final trick to completing the repair: Use the
repaired area to paint or carve on so that your design or painting covers the
repair even more!
The Shining:
Start with rough steel wool, or a piece of glass to scrape off the "rough" on the
outside of the horn. When you have basically a smooth horn, that just needs
extensive refinement, or polishing, then switch to a very fine grade steel wool.
use lots of elbow grease. Scrub the outside of the horn until you get a smooth,
sanded-like surface. You'll want to use finer and finer grades of steel wool to
further smooth your surface. You'll still feel the scratches of the steel wool, esp.
if your fingertips are sensitive. You'll also see lots of extremely tiny scratches.
Eventually, the horn will feel glassy smooth to your fingers. If your horn is very
dry to start with, it doesn't hurt to moisten it during the sanding process. You
can use water, but that dries quickly and has to be constantly reapplied. You
can also use honing oil. Honing oil is often used on whetstones used to
sharpen knives, so you should be able to pick some up in a sporting department
of a big store, or in any place that specializes in selling knives. Now, use the
inside "suede" edge of a piece of leather -the "rougher" the better. Again, lots of
elbow grease. Finally, finish with a jeweler's cloth. You'll eventually create a
mirror-like sheen on the outside surface of the horn! Some people like to coat
the outside of a horn with a varnish in order to keep the outside glossy and
smooth. That's fine, if you want to do that. It probably DOES extend the life of
the horn. If you are going to paint or carve on your horn though, you should
wait to varnish it until you've completed all your decorating.
The Curing:
I don't know how necessary this is.... But to "cure" my horns, I use Guiness
extra stout. It is heavy, and dark, and has a very strong taste, so I imagine that
it "soaks" into the fiber of the horn better than a weaker ale would... Anyway, I
stand the horn so that the rim is absolutely level, and fill it all the way up with
Guiness. Every 4 hours or so, you should check it and refill it to the top of the
rim. After 24 hours, you can pour the Guiness out, and rinse the horn
thoroughly. You're done! This horn should last you forever, you use no wax, so
you'll never get wax in your drink, or melted all over your car seat on long trips...
You use no plastic to coat the inside, so you never have to worry about whether
or not you're drinking a possibly toxic plastic in with your mead! The only care
the horn will require is washing out after being used. In my experience, you
don't want to let a beverage with foam sit in your horn for more than a few
hours, otherwise a "stain" from the foam begins to form on the sides of the horn,
a stain which takes ALOT of elbow grease to remove!
Decorating:
Your horn can be decorated a number of ways. You can draw on the skin of the
horn with a pencil, and then erase any mistakes innumerable times. Finally,
when your drawing is adequate, you can fill in the lines with the paint of your
choice. A good acrylic paint works fine, especially if you "seal" it in with a coat
of laquer or varnish when you're done. You can carve runes or pictures into the
skin of the horn with a dremel tool or with a good sharp knife. Either way, it
takes a steady hand to carve out the detail, but when you're finished with your
horn, you'll have something to be proud of at every gathering you attend, and
the knowledge that you made it yourself will fill you with a very satisfied sense
of accomplishment.
Troubles:
I just can't get the damned thing clean!
. Okay, Fill half full with boiling water, pour in some soap, cover rim with
something other than your hand! Shake well, fill the rest of the way up with
boiling water, let sit until water is totally cool. Repeat, however this time begin
scrubbing with a bristle bottle cleaner when water is cool enough to tolerate.
Additionally, you may want to pour a solution of water and bleach (use very little
bleach in your mixture) into the horn, esp. if there are areas far down, that you
don't feel you could clean with the brush. Let this sit, then rinse repeatedly. The
"curing" process will cover up the smell of the bleach. Another good trick is to
use Polident! Yes, fill the horn full of hot water, then start dropping Polident
tablets into the water. Be sure to use plenty of Polident in the water, if you have
a large horn, it may require lots of Polident. I used this trick with a horn that
held 2 quarts of water, and I had to use 7 Polident tablets to achieve the right
effect! Depending on the color of the Polident tablets, your water will begin to
foam and bubble, then turn the color of the tablets (usually green, in my
experience). Let the water sit for a while (at least 30 minutes) then pour out the
top fourth, and begin to scrub with your bottle brush. The Polident should have
loosened up any debris inside the horn, making it easier for you to scrub it out.
I wish it would stand up!
. No problem. Have you ever seen those candle holders are the craft stores that
have three metal legs, connected by a circle of metal? These, or something
based on their design work wonders holding up horn. Buy or make one taller
and wider than you need. Then wrap leather cord, or animal skin around the
central metal circle, so that your horn fits tightly when sitting in the circle. Your
horn should stop sliding through about 1/3 of the way from the rim, or several
inches from the rim, anyway. Now you have a stand for your horn that you can
use on your Harrow or on the ground. Also, you can acquire "Doll Stands" at
most craft-hobby stores.. These work passably well at holding up the longer
horns that hold a smaller volume of liquid. The ones I've tried to use are a bit to
fragile to trust if your horn holds more than 12 ounces.
My bottle brush isn't long enough to reach all the way down!
. We'll make a tool for you to use. First, decide on an old washcloth or old sock
that you can sacrifice to the project. Take a wire coat hanger and straighten it
out. Now, put a tight loop on one end of the wire hanger, such that the wires
loops back onto itself. Make sure that there is at least an inch of hanger left
over, past where the end loops back onto itself. Now, punch a hole near one
edge of the sock or cloth. Insert the hanger end through the cloth, then twist
that extra inch of hanger around the main "long" part of the hanger. You may
need to use pliers to do this. It's very important that your hanger does not have
any sharp end sticking out, or you will gouge the soft inside of the horn!
Finally, wrap the cloth around the hanger and secure it with a bread tie. Again,
make sure the bread tie has no sharp ends sticking out! Additionally, you
should make note of which direction you twisted the cloth, and when you scrub
the horn with it, make sure you do not twist your hanger in the opposite direction
as this will have the unfortunate effect of unraveling your cloth from your
hanger. To complete your tool, you can bend the "handle" end of the hanger
into a comfortable grip for your hand, and bend the body of the hanger into a
curve that will allow the end to reach the bottom of the horn. Done correctly
this tool should allow you to reach the depths of even the longest horn!
What is the traditional/ritual reason/basis for use of a drinking horn?
The drinking horn is one of the utensils most commonly associated with Vikings,
though it was coming into disuse in the viking period as the Northern peoples
attempted to acquire the more Roman glasses and steins. Even though the
Roman ways were being adopted, to some extent, still the drinking horn
continued to hold a certain authority and mystique for our ancestors, and does
even down to this day. The mightiest chieftains entertained the fellows and
their warriors in long halls wherein stout ale or mead was served in drinking
horns, and this was the height of power and propriety. The horn of the aurochs
bull was prized above all others. This fierce wild bull/ox was the paradigm of
strength and the warriors who could claim its horns were held to be the bravest
of all! Natural horns are especially important to us today, as they are a living
symbol of our link to the earth and the past. When we drink from a horn which
was once a part of an animal, we are reminded how we are all Earth's children,
and how we and the animals of this planet are interdependent and forever
linked to one another. We are reminded, too of our noble ancestors, and their
great deeds of boldness and daring, and how they too are a part of us. It is
easy not to remember these things when lifting a modern glass to one's lips, or
just drinking from a bottle or a can. Those things are not bad, in and of
themselves, but they do not symbolize the kinds of things that we wish to be
reminded of during holy blessings. Two of Denmark's most prized possessions
(recently stolen and melted) were the Gallehus drinking horns - several pounds
of solid gold, decorated with religious symbols and images of people and beasts
which may have represented scenes from cultic drama. Though these were not
"natural" horns, they obviously were created to serve a very high purpose as a
symbol of might, power, wealth, and the past.
The horn is associated with Odin more so than many other Norse gods.
Bjørnsterne Bjørnson/Edvard Grieg said, "Now lift high the horn, Host-Father
Óðinn's horn...Holy hof-fires, Ake-Thórr's Hammer-Sign, holy hof-fires hallowed
it here" in the operatic fragment Olav Trygvason. One of the stories in Asatru is
that Odin sends his Valkyries to greet the fallen heroes as they enter his hall
with a draught from a drinking horn which heals them and restores their vigor.
If that were not enough of a connection, Odin is said to not eat, but to only drink
mead. The horn has come to symbolize for modern Asatru Heathens the very
essence of our religion. Natural, and with roots in the past, it sets up the
attitude and atmosphere that we strive for, and our primary form of communing
with our gods is by offering them a drink (blót) from our ceremonial drinking
horns, and by raising our horns to them in ritual, we give them honor and
rememberance.
Colheita e preparação:
Quando você escolher uma buzina para usar como um chifre, há um par de
coisas para procurar. Primeiro, considerar o tamanho total e forma da buzina.
Vai ser pendurado em seu pescoço? Qual borda do aro parece ser moldado
sobre a direita para beber a partir de? E se você beber esse lado, então a
ponta do chifre estar apontando para cima, ou para baixo? Se ele está
apontando para cima, que é melhor, porque o líquido não tenderá a "splash",
mas derramará sem problemas. Será que o chifre ainda tem um "núcleo" para
limpar? Isso leva uma quantidade considerável de trabalho. Quão pesado é?
Você vai estar segurando-o na mão por longos períodos? Qual é a espessura
da bainha exterior efectivo (em oposição à medula / núcleo)? Se o revestimento
externo é grosso, então o seu chifre vai realizar muito menos líquido do que
pode parecer capaz. Em alguns chifres, a área interior "aberto" termina perto
do aro, e toda a parte do meio para a ponta é toda sólido. Se você pode ...
testar a buzina para ver se ele vai reter a água, sem vazamento. Vazamentos
podem ser reparados, mas isso significa mais trabalho para você! Você
também pode ter uma idéia de quanto fluido o chifre vai segurar
confortavelmente desta forma.
Limpeza:
Eu gosto de fazer meus chifres de beber, no que eu considero o caminho
"natural". Eu li como alguns cera de abelha, uso ou revestimentos saladeira, ou
alguma outra substância para revestir o interior do chifre, mas que parece ser
um policial-out para mim. Quando eu adquirir um chifre eu costumo comprar
uma que já é "cored" e não há chifre medula para limpar. No entanto, se você
tem um núcleo ainda na trompa, pode ser necessário fervê-la para fora. Ferve-
se a buzina, completamente submerso na água durante pelo menos 6 horas.
Levante cuidadosamente a buzina, e eu gosto de usar um saca-rolhas para
testar a rigidez do núcleo. Deve ser muito macio e flexível agora. Demasiada
de ebulição, e que deve ser goop! Você pode obter grandes pedaços com o
saca-rolhas, ou uma picareta. Se você ligar a buzina borda para baixo, firme e
bater-lo sobre uma mesa, a maioria do núcleo deve cair. Se você tem uma
colher de sopa que você pode poupar, eu sugiro limar as arestas para baixo em
uma nítida vantagem, e usar isso para erguer / retire o núcleo. Você precisa
colocar o chifre de volta para a água fervente para que o núcleo mais abaixo
pode ser aquecido, uma vez que você tenha removido a parte perto da borda.
Se você verificar a sua buzina a cada 2 horas você está muito seguro para
ferver. A buzina vai ficar "mole" depois de um tempo, mas enquanto você não
cicatriz de fora com uma pinça ou algo assim, quando pegá-la, você pode
facilmente voltar a moldá-lo se ele começa a achatar devido a toda a ebulição.
Além disso, acho que é conveniente para colocar algo no fundo da panela, para
que o chifre não está diretamente tocar a superfície do fundo do pote que você
está dentro de água fervente Caso contrário, a ponta do chifre vai aquecer mais
rápido que os demais, e isso pode causar-lhe a dobrar, quebrar ou achatar. Ser
paciente tirar o núcleo .. Às vezes, levando o chifre para fora, e deixá-lo esfriar
e secar irá revelar que o núcleo pode agora ser erguida com a sua colher /
raspador. Depois de o núcleo está fora .. você tem que começar a limpeza do
chifre! Eu preenchê-lo com água fervente, e esperar para ver se algum
vazamento desenvolver. Tome nota dos vazamentos, e nós repará-los mais
tarde. Eu recebo uma série de garrafa-escovas e suavemente, mas com
firmeza, esfregue o interior do chifre, ao derramar a água, fervendo e sabão
através de intervalos, para enxaguá-lo. A escova de cerdas é fundamental ...
Você tem que encontrar uma escova de cerdas que tem ao lado, e estendendo-
se até o topo também. Caso contrário, quando você tenta empurrar o pincel na
buzina, a ponta de metal da escova possivelmente irá raspar sulcos na parede
calor amolecida interior da trompa. Depois de passar por este processo muitas
e muitas vezes. Eu recebo um chifre que é perfeitamente limpo por dentro!
O teste:
A prova disso, é colocar puro, água potável engarrafada no chifre, e quando
sua paleta é perfeitamente neutra, saborear um pouco da água, e açoitar-lo
como se fosse prova de vinhos. engolir. derramar sobre metade da água, e
cobrir a abertura do chifre, e agite a água restante ao redor. gole e swish
novamente. Se você não tem gosto "tesão", após isso, então você tem um
chifre limpo!
Reparação:
Se o seu chifre tem algum vazamento, ou lágrimas que você pode usar não-
tóxico dedo cola de reparação de unhas (esta é uma substância usada para
reparar e fortalecer as unhas, e con ser encontrado na maioria das lojas
grandes) para preencher o buraco, ou reconstruir um pequeno parte do chifre
falta.
Além disso, se tiver "bolhas" ou "flocos" de corno de material se solte do lado
de fora da buzina, estes podem ser reparadas de uma maneira semelhante.
Para estes problemas, é normalmente mais fácil referver a buzina, até que seja
muito flexível, em seguida, pressionar firmemente as bolhas ou flocos para
baixo até que eles são tão plana contra o corno como eles vão. Ora, se se trata
de um floco, e tem uma fenda aberta na mesma, derramar a cola reparação
unha na fenda, e manter forçando-a até que a fenda inteiro está cheio. Para
bolhas, você precisa cortar o "borbulhava" parte da pele chifre, em seguida,
aplicar a cola de reparação unha em todas as bordas da bolha onde você
cortar a parte elevada. Arquivo para baixo qualquer cola reparação excesso
unha, e usando lã de aço de grão fino, criar um brilho próximo ao da pele chifre
regular. Terminar como de costume, com um pano joalheiro rouge e seu ponto
de reparo deve ser muito próximo a níveis indetectáveis. Um truque final para a
conclusão do reparo: Use a área reparada para pintar ou esculpir na forma que
o seu desenho ou pintura cobre a reparação ainda mais!
O Iluminado:
Comece com lã de aço grosseira, ou uma peça de vidro para retirar o "bruto"
do lado de fora da trompa. Quando você tem basicamente o chifre de um
suave, que só precisa de refinamento extensa, ou polimento, em seguida,
mudar para uma lã muito fina grade de aço. utilização de lotes de graxa de
cotovelo. Esfregue a parte externa do chifre até obter uma superfície lisa,
lixada-like. Você vai querer usar notas cada vez mais finas de lã de aço para
suavizar ainda mais a sua superfície. Você ainda vai sentir os arranhões da lã
de aço, esp. se os seus dedos são sensíveis. Você também vai ver um monte
de riscos extremamente pequenas. Eventualmente, a buzina vai se sentir
suave vítrea para os dedos. Se o seu chifre é muito seco, para começar, não
faz mal para umedecê-la durante o processo de lixamento. Você pode usar
água, mas que seca rapidamente e tem de ser constantemente reaplicados.
Você também pode usar o óleo de afiar. Óleo de afiar é usado frequentemente
em amolar usados para afiar facas, assim que você deve ser capaz de escolher
alguns para cima em um departamento esportivo de uma grande loja, ou em
qualquer lugar que é especializado na venda de facas. Agora, use o bordo
interior "camurça" de uma peça de couro, o "grosseiro", melhor. Mais uma vez,
muita graxa de cotovelo. Por fim, termine com um pano de um joalheiro. Você
eventualmente criar um brilho espelhado na superfície exterior do chifre!
Algumas pessoas gostam de revestimento do lado de fora de uma trompa com
um verniz de modo a manter o exterior lustroso e liso. Isso é bom, se você
quiser fazer isso. É muito provável que se estende a vida do chifre. Se você
estiver indo para pintar ou esculpir na sua buzina, porém, você deve esperar
para verniz até que tenha concluído todos os seus decoração.
A Cura:
Eu não sei como isso é necessário .... Mas, para "curar" os meus chifres, eu
uso stout Guinness extra. É pesado e escuro, e tem um sabor muito forte,
então eu imagino que "absorve" na fibra do chifre melhor do que uma cerveja
mais fraca iria ... De qualquer forma, estou a buzina para que o aro é
absolutamente nível, e preenchê-lo todo o caminho até com Guiness. A cada 4
horas ou assim, você deve verificá-la e recarregá-lo ao topo do aro. Após 24
horas, você pode derramar o Guiness para fora, e lavar o chifre
completamente. Está pronto! Este chifre deve durar para sempre, você não
usar cera, para que você nunca vai conseguir cera em sua bebida, ou derretido
todo o seu assento de carro em viagens longas ... Você não usar plástico para
revestir o interior, assim você nunca tem que se preocupar se você está ou não
beber um plástico, possivelmente tóxicos com seu hidromel! O único cuidado a
buzina vai exigir é lavagem após o uso. Na minha experiência, você não quer
deixar a bebida com sit espuma em seu chifre por mais de algumas horas, caso
contrário, uma "mancha" da espuma começa a se formar sobre os lados do
chifre, uma mancha que tem um monte de cotovelo graxa para remover!
Decoração:
Seu corno pode ser decorado de uma série de maneiras. Você pode desenhar
sobre a pele do chifre com um lápis e, em seguida, apagar as inúmeras vezes
erros. Finalmente, quando seu desenho é adequado, você pode preencher as
linhas com a tinta de sua escolha. A tinta acrílica boa funciona bem,
especialmente se você "selo" em com uma camada de verniz ou verniz quando
você está feito. Pode esculpir runas ou imagens na pele do corno com uma
ferramenta dremel ou com uma faca bem afiada. De qualquer maneira, é
preciso uma mão firme para esculpir o detalhe, mas quando você está acabado
com a sua buzina, você terá algo de que se orgulhar em todas as reuniões que
participar, e os conhecimentos que você fez isso a si mesmo vai enchê-lo com
um sentido muito satisfeito de realização.
Problemas:
Eu simplesmente não pode obter a maldita coisa limpa!
. Ok, Preencha meio cheio com água a ferver, despeje um pouco de sabão,
cobrir borda com outra coisa que não a sua mão! Agite bem, preencher o resto
do caminho com água fervente, deixe descansar até que a água é totalmente
legal. Repetir, no entanto, este tempo começou esfregar com um limpador de
garrafa de cerdas quando a água é fria o suficiente para tolerar. Além disso,
você pode querer derramar uma solução de água e água sanitária (alvejante
usar muito pouco em sua mistura) na buzina, esp. se existem áreas muito
baixo, que você não sente que você pode limpar com a escova. Deixe que este
sente-se, em seguida, lavar repetidamente. O processo de "cura" vai encobrir o
cheiro da água sanitária. Outro bom truque é usar Polident! Sim, preencher o
chifre cheio de água quente, em seguida, começar a cair comprimidos Polident
na água. Certifique-se de usar de muita Polident na água, se você tem um
grande chifre, pode exigir muita Polident. Eu usei esse truque com um chifre
que realizou 2 litros de água, e eu tive que usar 7 comprimidos Polident para
conseguir o efeito certo! Dependendo da cor dos comprimidos Polident, a água
começará a espuma e bolhas, vire a cor dos comprimidos (geralmente verde,
na minha experiência). Deixe a água descansar por um tempo (pelo menos 30
minutos) em seguida, despeje o quarto superior, e começa a esfregar com sua
escova de garrafa. O Polident deveria ter se soltou todos os restos no interior
do chifre, o que torna mais fácil para você esfrega-lo para fora.
Gostaria que fique de pé!
. Sem problemas. Você já viu os castiçais são as lojas de artesanato que têm
três pernas de metal, conectados por um círculo de metal? Estes, ou algo com
base em seu trabalho de design pergunta segurando corneta. Comprar ou fazer
um alto e mais largo do que você precisa. Em seguida, enrole cordão de couro
ou pele animal em todo o círculo de metal central, de modo que seu chifre se
encaixa bem ao sentar-se no círculo. Seu chifre deve parar de correr por cerca
de 1/3 do caminho da borda, ou vários centímetros da borda, de qualquer
maneira. Agora você tem um suporte para o seu chifre que você pode usar em
seu Harrow ou no chão. Além disso, você pode adquirir "Boneca Stands" na
maioria das lojas de artesanato passatempo-.. Estes funcionam razoavelmente
bem em segurar os chifres mais longos que possuem um menor volume de
líquido. Os que eu tentei usar são um pouco a frágil a confiança se seu chifre
tem mais de 12 onças.
Minha escova de garrafa não é tempo suficiente para chegar até o fim!
. Nós vamos fazer uma ferramenta para você usar. Primeiro, decidir sobre uma
toalha velha ou meia velha que você pode sacrificar para o projeto. Pegue um
cabide de arame e endireitar. Agora, colocar um laço apertado sobre uma
extremidade do gancho de arame, de tal forma que os fios de laços de volta
sobre si mesma. Certifique-se de que há pelo menos uma polegada de cabide
de sobra, passado, onde o fim loops de volta para si mesmo. Agora, perfurar
um furo próximo de uma extremidade da meia ou pano. Insira o fim cabide
através do pano, torça essa polegada extra de gancho em torno da principal
parte "longa" do cabide. Você pode precisar usar um alicate para fazer isso. É
muito importante que o seu cabide não tem qualquer ponta afiada de fora, ou
você vai arrancar o interior macio do chifre! Finalmente, enrole o pano em torno
do cabide e prenda-o com um laço pão. Mais uma vez, certifique-se o empate
pão não tem pontas afiadas saindo! Além disso, você deve tomar nota de qual
direção você torceu o pano, e quando você esfrega a buzina com isso,
certifique-se que você não torcer o gancho na direção oposta, pois isso terá o
efeito infeliz de desvendar o seu pano de seu cabide. Para completar a sua
ferramenta, você pode dobrar o "cabo" fim do cabide em um aperto confortável
para sua mão, e dobrar o corpo do cabide em uma curva que permita que o
final para chegar ao fundo do chifre. Feito corretamente essa ferramenta deve
permitir que você alcance as profundezas do mesmo chifre a mais longa!
O que é o ritual tradicional / razão / base para o uso de um chifre de beber?
O chifre é um dos utensílios mais comumente associados com os Vikings,
apesar de que estava chegando em desuso no período viking como os povos
do Norte tentou adquirir os óculos mais romanas e steins. Mesmo que os
caminhos romanos foram sendo adotadas, em alguma medida, ainda o chifre
continuou a manter uma certa autoridade e mística para nossos ancestrais, e
faz mesmo até este dia. Os chefes mais poderosos entreter os companheiros e
seus guerreiros em longos corredores onde cerveja stout ou hidromel foi
servido em beber chifres, e esta era a altura de poder e propriedade. O chifre
do touro auroque foi valorizada acima de todos os outros. Este touro feroz
selvagem / boi era o paradigma da força e os guerreiros que poderia reivindicar
seus chifres foram considerados os mais corajosos de todos! Chifres naturais
são especialmente importantes para nós, hoje, como eles são um símbolo vivo
da nossa ligação à terra e ao passado. Quando bebemos de um chifre que era
uma vez uma parte de um animal, somos lembrados de como somos todos
filhos da Terra, e como nós e os animais deste planeta são interdependentes e
para sempre ligados um ao outro. Somos lembrados também de nossos
antepassados nobres, e seus grandes feitos de coragem e ousadia, e como
eles também são uma parte de nós. É fácil não se lembrar dessas coisas
quando levantar um copo moderno para os lábios, ou apenas beber de uma
garrafa ou uma lata. Essas coisas não são ruins, em si mesmos, mas eles não
simbolizam os tipos de coisas que queremos ser lembrados durante as
bênçãos sagradas. Dois dos bens mais valiosos da Dinamarca (recentemente
roubado e derretido) foram os chifres bebendo Gallehus - vários quilos de ouro
maciço, decorado com símbolos religiosos e imagens de pessoas e animais
que podem ter representadas cenas do drama de culto. Embora estes não
eram "naturais" chifres, que, obviamente, foram criadas para servir a um
propósito muito alto como um símbolo de poder poder, riqueza, e do passado.
O chifre é associada com Odin mais do que muitos outros deuses nórdicos.
Bjørnsterne Bjørnson / Edvard Grieg disse: "Agora levante alto a buzina, Host-
Pai Óðinn chifre ... Santo hof-incêndios, Ake-Thórr Hammer-Sinal, santo hof-
dispara santificou aqui" na ópera fragmento Olav Trygvason. Uma das histórias
em Asatru é que Odin envia seus Valquírias para saudar os heróis caídos que
entra seu salão com um projecto de um chifre que os cura e restaura seu vigor.
Se isso não fosse o suficiente de uma conexão, Odin é dito para não comer,
mas apenas para beber hidromel. A buzina passou a simbolizar para os
modernos Asatru ateus a própria essência de nossa religião. Natural, e com
raízes no passado, ele define a atitude ea atmosfera que nós nos esforçamos
para, e nossa primeira forma de comunhão com os nossos deuses é oferecer-
lhes uma bebida (blot) de nossos chifres bebendo cerimoniais, e aumentando
os nossos chifres para eles no ritual, damos-lhes honra e recordação.