MAKING MODERN LIVING POSSIBLE · 2019-08-15 · 2 FP715SI GB FP715Si Electronic 2-Channel Full...
Transcript of MAKING MODERN LIVING POSSIBLE · 2019-08-15 · 2 FP715SI GB FP715Si Electronic 2-Channel Full...
User GuideDanfoss Heating
MAKING MODERN LIVING POSSIBLE
FP715SiElectronic 2-Channel Full Programmer for
Heating and Hot Water with Service Interval Timer
FP715SI2
GB
FP715SiElectronic 2-Channel Full Programmer for Heating & Hot Water with Service Interval Timer
For a large print version of these instructions please call Marketing on 0845 121 7400.
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other printed material. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
®
Certification Mark
Danfoss Heating 3
GBThank you for buying a Danfoss product GB
FP715SI4
GB
Index
1.0 User Instructions 1.1 Your Programmer ...........................................................................6 1.2 Preset Programmes .......................................................................6 1.3 Before you start ..............................................................................7 1.4 Choice of 24hr or AM/PM display.............................................7 1.5 Setting the Date and Time ..........................................................7 1.6 Accepting the Preset Programmes ..........................................8 1.7 Before you Change the Preset Programmes ........................9 1.7.1 Programming the Heating in 5/2 Day Mode..................... 10 1.7.2 Programming the Heating in 7 Day Mode ......................... 11 1.7.3 Programming the Heating in 24 Hour Mode .................... 12 1.8 Programming your Hot Water ................................................ 13 1.9 Running your Programme ....................................................... 14
2.0 Advanced 2.1 Temporary Override Buttons .................................................. 15 2.2 Holiday Programme ................................................................... 16 2.3 Changing Clocks Forward and Backward .......................... 17 2.4 Service Interval Timer ................................................................ 18 2.5 Making a Full Reset .................................................................... 19 2.6 Fault Check List ............................................................................ 20
DAY/HOL
Central Heating1HR override
Central HeatingMAN override
RESET
Central Heating Mode SELECT
+1HR
MAN
+1HR
MAN
Hot Water1HR override
Hot WaterMAN override
Hot WaterMode SELECT
Danfoss Heating 5
GB
What is a Programmer?
... an explanation for householders.Programmers allow you to set ‘On’ and ‘Off ’ time periods. Some models switch the central heating and domestic hot water on and off at the same time, while others allow the domestic hot water and heating to come on and go off at diff erent times.Set the ‘On’ and ‘Off ’ time periods to suit your own lifestyle. On some programmers you must also set whether you want the heating and hot water to run continuously, run under the chosen ‘On’ and ‘Off ’ heating periods, or be permanently off .The time on the programmer must be correct. Some types have to be adjusted in spring and autumn at the changes between Greenwich Mean Time and British Summer Time.You may be able to temporarily adjust the heating programme, for example, ‘Override’, ‘Advance’ or ‘Boost’. These are explained in the manufacturer’s instructions.The heating will not work if the room thermostat has switched the heating off . And, if you have a hot-water cylinder, the water heating will not work if the cylinder thermostat detects that the hot water has reached the correct temperature.
The text below has been edited and approved by the Plain English Campaign, who has issued a Crystal Mark
to be displayed with it.
FP715SI6
GB
1.0 User Instructions1.1 Your Programmer
The FP715 Si allows you to switch your heating and hot water on and off at times that suit you.
Your programmer has had the date and time set up during manufacture and will automatically change between Greenwich Mean Time and British Summer Time.
You can programme up to 3 ON/OFF times per day for the heating and the hot water and the two systems can be operated independently.
1.2 Preset Programmes
Your FP715 Si comes ready programmed with a set of operating times which often suit most people.
If you want to change any of these settings, you can do so by following the instructions on pages 9-14. First, follow the steps on page 7-8 to set the correct time and date.
Event No.Hot Water and
Heating Mon-Fri Sat-Sun**
1 1st ON 6:30 7:30
2 1st OFF 8:30 10:00
3* 2nd ON* 12:00* 12:00*
4* 2nd OFF* 12:00* 12:00*
5 3rd ON 17:00 17:00
6 3rd OFF 22:30 22:30
* Not applicable if unit set to 2 ON/OFF’s per day by installer**Not applicable if unit set to 24 hour mode by installerSee page 9 for explanations of diff erent settings
Danfoss Heating 7
GB
1.3 Before you start
Open the fl ap on the front of the clock. Press the RESET button using a non-metallic object (e.g. pencil/matchstick) until you hear a click and the 2 red lights on the front of the unit fl ash once.
This will stop and restart the electronics, without losing the factory set time and date settings.
To fully reset the unit see page 19.
1.4 Choice of 24hr or AM/PM display
Press and hold DAY/HOL and NEXT ON/OFF for 1.5 seconds to toggle between 24hr clock and AM/PM display, as required.
1.5 Setting the Date and Time
These settings are made during manufacture and only need to be changed in the unlikely event that the unit has lost the settings.
Setting the DatePress and hold PROG for 5 seconds to display year.
Use the + or - buttons to set the correct year.
DAY/HOL
DAY/HOL
DAY/HOL
DAY/HOL
FP715SI8
GB
Press DAY/HOL to display day and month. Use the + or - buttons to set the correct month (Jan = 1, Feb = 2 etc.).
Press DAY/HOL to display day and month. Use the + or - buttons to set day of month.
Press PROG to display the time.
The words SET TIME will appear at the top of the display and the time will fl ash on and off .
Use the + or - buttons to set the correct time (press and hold to change in 10 min. increments).
Setting the Day The day of the week is set automatically.
1.6 Accepting the preset programmes
If you are happy to use the preset programmes on page 6, you don’t need to do anything else.
Press the PROG button once to return to run mode.
�
Danfoss Heating 9
GB
1.7 Before you change the preset programmes
Your installer will have set your unit to operate in one of the following modes:
• 5/2 day - one set of programmes for weekdays and another for weekends (page 10-11)
• 7 day - diff erent settings for each day of the week. (page 11-12)• 24 hour - one set of programmes for the whole week. (page 12-13)
See INSTALLER SETTING tick box on inside fl ap label to ascertain which mode your unit is set.
Please Note
The unit must be programmed in sequence. ON/OFF times cannot be set out of sequence. If you want to leave a preset time as it is, simply press NEXT to move on to the next setting.
Your installer will have set your unit to programme either 2 or 3 ON/OFFs per day. If your clock has been installed to allow 3 ON/OFFs and you do not wish to use one of the ON/OFF settings, simply programme the ON time to be the same as the OFF time and the setting will not operate.
INSTALLER SETTING24 Hour5+2 Day7 Day
FP715SI10
GB
1. Press PROG once until SET CH ON TIME appears at the top of the display and MOTUWETHFR appears at the bottom of the display.
Use the + or - buttons to set the time you would like your heating to fi rst come on in the morning (Event 1).
2. Press NEXT ON/OFF once only.
Use the + or - buttons to set the time you want your heating to go off (Event 2).
To move to the next setting, i.e. when you would like your heating to come on again (Event 3) press the NEXT ON/OFF button again.
3. Continue programming the central heating ON and OFF times for weekday Events 4, 5 & 6 as in Step 2.
4. Press the DAY/HOL button once and SASU will appear at the bottom of the display.
DAY/HOL
DAY/HOL
DAY/HOL
1.7.1 Programming the heating in 5/2 day mode
DAY/HOL
Danfoss Heating 11
GB
If the same programme is required press the COPY button and the previous days programme will be entered.
If a diff erent programme is required repeat steps 2-4.
5. Press the PROG button once to enter hot water programming or twice to return to run mode.
6. Proceed to page 14.
Please NoteIf this setting is made on a weekend day SASU will show in place of MOTUWETHFR.
DAY/HOL
DAY/HOL
1. Press PROG once until SET CH ON TIME appears at the top of the display. Note the current day is displayed. Press the DAY/HOL button until the required day is displayed.
2. Use the + or - buttons to set the
time you want your heating to fi rst come on in the morning (Event 1).
3. Press NEXT ON/OFF to move to Event 2.
DAY/HOL
DAY/HOL
1.7.2 Programming the heating in 7 day mode
FP715SI12
GB
DAY/HOL
DAY/HOL
4. Continue programming the central heating ON and OFF times in this way by using the + or - buttons to set the time you want and pressing the NEXT ON/OFF button to move to the next setting.
5. Press DAY/HOL button once only.
The next day will appear at the bottom of the display. Repeat steps 2-5.
6. Press the PROG button twice to return the unit to RUN mode (time appears and the colon in the display begins to fl ash).
7. Proceed to page 14.
DAY/HOL
1. Press PROG once until SET CH ON TIME appears at the top of the display.
Use the + or - buttons to set the time you want your heating to fi rst come on in the morning (Event 1).
2. Press NEXT ON/OFF to move to Event 2.
Continue programming the central heating ON and OFF times by pressing:
DAY/HOL
DAY/HOL
1.7.3 Programming the heating in 24 hour mode
Danfoss Heating 13
a) NEXT ON/OFF button to move to the next setting,
b) + or - buttons to amend the time.
3. Press the PROG button twice to return the unit to RUN mode (time appears and colon in the display begins to fl ash).
4. Proceed to page 14.
GB
DAY/HOL
DAY/HOL
1.8 Programming your Hot Water
To set the hot water programme press the PROG button twice until SET HW ON TIME appears on the display.
Set the hot water programme in the same way as the heating programme, using:
a) + and - buttons to alter the time,
b) Pressing the NEXT ON/OFF button to move to the next setting,
c) Pressing DAY/HOL to advance through days of the week (7 day mode) or to advance to Saturday and Sunday programming (5/2 day mode) and repeat steps a-c.
DAY/HOL
DAY/HOL
DAY/HOL
DAY/HOL
FP715SI14
GB
Finally press PROG once to return the unit to run mode (time appears and colon in the display begins to fl ash).
DAY/HOL
To run the central heating programme: press the SELECT button next to the radiator symbol until AUTO
is displayed in the LCD.
To run the hot water programme: press the SELECT button next to the tap symbol until AUTO is
displayed in the LCD.
As you press the SELECT button the display will change between ON, OFF, ALLDAY and AUTO.
• AUTO = the heating/hot water will come on and go off at the
programmed times.
• ON = the heating/hot water will remain on constantly.
• OFF = the heating/hot water will not come on.
• ALLDAY = the clock will turn the heating/hot water on at
the fi rst programmed ON and will leave it on until your last
programmed OFF.
Select the option you require depending on your circumstances, time of year, etc.
���
��
������
1.9 Running Your Programme
Danfoss Heating 15
GB
The grey buttons next to the radiator symbol are the Heating override buttons.
The grey buttons next to the tap symbol are the Hot Water override buttons.
+1HR Pressing this button when either system is in AUTO or ALLDAY mode will cause the heating/hot water to remain on for an extra hour. If it is pressed while the programme is OFF the heating/hot water will come on immediately for 1 hour then go off again. +1HR will be shown in the display.
MAN Pressing this button when either system is in AUTO or
ALLDAY mode will cause the heating/hot water to go OFF until the next programmed ON, or vice versa. MAN will be shown in the display.
Sometimes you may need to change the way you use your heating temporarily, i.e. due to unusually cold weather. The FP715 Si has two convenient overrides which can be selected without aff ecting the set programme.
+1HR
MAN
+1HR
MAN
+1HR
MAN
+1HR
MAN
2.0 Advanced Settings2.1 Temporary Override Buttons
FP715SI16
GB
To automatically bring the heating back on when returning from holiday the FP715-Si has a built in holiday feature.
Follow the steps below to set the date that the heating system needs to come back on.
1. Press DAY/HOL
2. Use the + or - buttons to select the year.
3. Press DAY/HOL, then use the + and - buttons to select the month.
4. Press DAY/HOL again, then use the + and - buttons to select the day in month.
5. Press DAY/HOL to turn heating off and enter holiday mode.
To cancel holiday mode press DAY/HOL.
DAY/HOL
DAY/HOL
2.2 Holiday Programme
Danfoss Heating 17
GB
This is handled automatically. Should the installer have turned off Automatic Time Change then follow the instructions below.
Open the fl ap on the front of the unit to reveal the programming buttons.
To change from Summer to Winter (clocks back) -
• press and hold - button
To change from Winter to Summer (clocks forward) -
• press and hold + button
! Take care when making this change for the fi rst time. If it is made in the wrong direction the unit will have to be reset
and any user-settings re-entered.
(See pages 7-8 on how to reset the unit and how to set the date, time and day).
2.3 Changing Clocks Forward and Backward
FP715SI18
GB
• If the property is owned by a landlord he may, for gas safety reasons, have instructed the installer to set the service interval timer.
• If set, 28 days prior to the boiler service due date, a momentary visual and audible warning will remind you to have the boiler serviced in the next 28 days. This will be repeated each day at noon.
• If the boiler is not serviced within 28 days the daily audible warning will sound for 1 minute at the beginning of each hour and must be cancelled each day by pressing any button on the unit.
• In addition, all overrides and programming buttons will be disabled and the heating and hot water will operate for a set portion of each programmed hour.
• The installer will cancel or reset the service interval timer as part of the boiler service.
• This is a gas safety feature that can only be accessed by an installer.
• When the service interval timer is set the service due date can be viewed in RUN mode by pressing and holding the COPY button.
2.4 Service Interval Timer
Danfoss Heating 19
GB
If it is necessary to fully reset the unit, excluding the date and time, follow the instructions below.
1. Press and hold the +1HR and MAN buttons on the left hand side of the product.
2. Press the RESET button and hold for 3 seconds.
3. Release the RESET button. The display will change to show the current time.
4. Finally, release both the +1HR and MAN buttons.
The unit is now fully reset and must be re-programmed, see pages 10-14.
+1HR
MAN
+1HR
MAN
Example
2.5 Making a Full Reset
FP715SI20
GB
�� ��� ����
����� ��� � �� ���� � �� � ��� ������� ������� �� ��� ��� ��� ���� ������� �� ���
�� ��� �� ����� � ��� ���� ������ ��! """ �� " ����� #��� �� #���� ���
"""""" $�� " ����� � ����� ��� ������
�� ��� ���� ��� �� � ����� ��� � �# %&'�! "" �� " �� � ���� �� %&'�
"""""" $�� " ����� �����
�� ��� ����� ��! """"" �� " ����� ��� ����� ��� ������
"""""" $�� " (��� ������ �� ��� �� )� �����
*�� ����� ���� �� ��+���� "" �� ����� ��! " �� " ����� ��� ���� ������
"""""" $�� " (��� ������ �� ��� �� )� �����
���� ��� ����� ���� ������ �� " ,�� ����� �����!" ��
"""""" $�� " (��� ������ �� ��� �� -& �����
��������� �� ����� .������ /������
0#�� ��� ���� ��� ���� ������1 ��� � ��� � �� ���� ��� ���� ���� ��� �� ��� �2�� �� ���������
�� ������
����� ��� � �� ���� � �� � ��� ���� ������� �� ��� ��� ��� ������� ������� �� ���
�� ��� �� ����� � ��� ������� ������ ��! "" �� " ����� #��� �� #���� ���
"""""" $�� " ����� ��� ��� ������
�� ����� ����� ��� ����� ���� ��� ����! "" �� " *�� ���� �� 3&'�
"""""" $�� " ����� �����
�� ��� ����� ��! """"" �� " ����� ����� ��� ������ �� ��� �� ��+�
"""""" $�� " 4������ � ������ �� ��� �� )� �����
*�� ����� ���� �� ��+���� �� ����� ��! "" �� " ����� ��� ���� ������
"""""" $�� " 4������ � ������ �� ��� �� )� �����
���� ��� ����� ���� ������ �� " ,�� ����� �����! " ��
"""""" $�� " 4������ � ������ �� ��� �� -& �����
��������� �� ����� .������ /������
0#�� ��� ������� ��� ���� ���� ��1 ��� � ��� � �� ���� ��� ���� ���� ��� �� ��� �2�� �� ���������
2.6 Fault Check List
Danfoss Heating 21
GB
FP715SI22
GB
Danfoss Heating 23
GB
Part No.38158v01s7-06 01/11
Danfoss Ltd.Ampthill RoadBedford MK42 9ER
Tel: 01234 364621Fax: 01234 219705Email: [email protected]: www.heating.danfoss.co.uk