Maginon Wk3 Hd Bda Uk description

7/21/2019 Maginon Wk3 Hd Bda Uk description

1/36


2/36


3/36

1

Dear customer,Congratulations on purchasing a high quality MAGINON product.

You have purchased a modern Wildlife Camera with excellent technical features and respective

accessory that is particularly easy to operate. Please study all notices carefully and diligently.

Please study this information in detail observing, in particular, the safety instructions.

The device comes with a 3 year warranty. You will need the enclosed warranty card and your sales

receipt in the event of the camera developing a fault.

Keep these in a safe place together with the Instruction Manual.

Please include the Instruction Manual when passing the camera on to a third party.

1. Contents of box

Carefully unpack camera and check that all of the following components are contained in the box:

1. MAGINON WK 3 HD

2. 4 GB SDHC memory card

3. 8 batteries type AA

4. Wall mount

5. Mounting belt

6. USB and video cable

7. Instruction manual

8. Warranty documents

Note:

Remove the protective foil from the camcorder lens by pulling the protruding tab.

Caution! Keep plastic foil and bags away from babies and small children, as otherwise danger

of suffocation.


4/36

2

1. CONTENTS OF BOX 1

2. CONTENTS 2

3. HAZARD, SAFET Y AND WARNING NOTICES 4

4. INTRODUCTION 7

5. YOUR CAMERA 8

5.1. Front view 8

5.2. Inside views 9

6. PREPARING THE CAMERA 116.1. Opening and closing the camera 11

6.2. Inserting the batteries 11

6.3. Inserting the memory card 12

6.4. External power supply 13

6.5. Assembly with strap 14

6.6. Using the wall mount 14

7. USING THE CAMERA 16

7.1. Mode switch 167.2. Operating buttons 16

7.3. Settings 18

7.4. Night recording 22

7.5. Setting up the live mode 22

7.6. Aligning the camera 23

7.7. File format 24

8. CONNECTING TO COMPUTER AND TV 25

8.1. Connection to computer 25

8.2. Connection to TV 26

9. TECHNICAL SPECIFIC ATION 27

2. Contents


5/36

3

10. SYSTEM INFORMATION, MAINTENANCE AND DISPOSAL 28

10.1. Care 28

10.2. Storage 28

10.3. Disposal 28

11. POTENTIAL LEGAL INFRINGEMENTS 29

12. WARRANTY AND SERVICE 30

13. CONFORMIT Y 30

14. INDEX 31


6/36

4

3. Hazard, safety and warning notices

Incorrect use of the camera and accessories can be dangerous for you and others and can damage ordestroy the camera. We therefore ask you to read and strictly observe the following Hazard, safety

and warning notices.

Intended use

This camera is intended for taking digital photos and video clips. It has been designed for private

use and is not suitable for commercial purposes.

Hazards for children and persons with limited ability to

operate electronic equipment The camera, accessory and packaging are not toys for children. These should therefore always

be kept away from children. Danger of electrocution, poisoning and suffocation.

The camera and accessory may not be used bychildren and persons with limited abilities.The

camera may only be operated by persons physically and mentally able to operate it safely.

Electrical hazard

Switch offthe camera and remove the batteries if a foreign body or liquid has entered the

camera.Let all parts dry thoroughly. Otherwise danger of fire or electrocution

Switch off the camera and remove the batteriesif the camerahas been droppedor the hou-

sing is damaged. Otherwise danger of fire and electrocution.

The camera maynot be dismantled, modified or repaired.Danger of fire and electrocution.

Only use a power adapter (not supplied) withthe mains voltage specified on the rating plate(6V).

Otherwise danger of fire or electrocution. Disconnect the power by pulling the power adapter out

of the socket.

A plugged-in power adapter (not supplied) can continue to use power and therefore represents a

hazard source.

The power supply may not be used during thunderstorms. Otherwise danger of electrocution.

Damage from heat fire hazard

Do not leave the camera in places that are susceptible to considerable increases in tempera-

ture (e.g. a vehicle). The housing and internal parts may be damaged, which in turn could cause a

fire.


7/36

5

Do not wrap up camera or place on textiles.This could produce a build up of heat in the camera

that can cause deformation of the housing and may represent a fire hazard.

Hazards of using batteries

Remove the batteriesfrom the camera if the camera is not used for some time.

Do not remove the battery immediatelyafter the camera has been used for a longer period of

time. The batteries may become hot during use.

There is a risk of explosion if the wrong type of batteries are used. Only use Type LR6 (AA) 1.5V

or NiMH batteries with the same specification.

Never expose the battery to excessive heat, such as direct sunlight, fire, etc., as otherwise danger

of fire. Consequently do not store batteries near fires, ovens or other heat sources.

Never store the batteries at temperatures below 10C and over 40C.

Keep the batteries out of reach of children.

Never store or transport a batteryin your pocket/tool box or similar, where it could come into

contact with metal objects.

Do not throw a battery into a fire, short-circuit a battery or take a battery apart.Danger of fire

and explosion.

Never touch leaking batteries without respective protection.In case of contact with skin, wash the

area with plenty of soap and water.

Avoid battery acid coming into contact with your eyes. In case of contact with eyes, rinse eyes with

plenty of water and contact a doctor immediately.

Disposeof batteries in accordance with the Batteries Directive.

Injuries and material damage

Only place the camera on sturdy surfaces.The camera could otherwise fall or topple over, causing

damage or injury.

Do not operate the camera whilst running or driving.You could fall or cause a traffic accident.

Only use a mains adapter (not supplied) for the camera, having the input voltage specified

on the rating plate (6V).We do not accept any liability for damage caused by the use of an

incorrect mains adapter.

The 230V socket used for the mains adapter (not supplied) must not be covered and accessible at

all times so that the mains adaptor can be quickly disconnected from the mains, when required.


8/36

6

Ensure adequate ventilation and do not cover the mains adaptor (not supplied) to avoid overhea-

ting.

Do not place any open ignition sources, such as lit candles onto or close to the device.

Do not subjectthe LCD monitor to impact or pressure.This could damage the glass of the monitor

or the liquid could leak from the inside. In case of contact with eyes or skin, rinse immediately with

clear water. In case of contact with eyes contact a doctor immediately.

Damageto the electronics, the monitor or the lens caused by external influencessuch as impacts,

falls or other are not covered by the warranty and must be paid for.

Do not drop or bump the camera and always handle it carefully. Otherwise the camera can be

damaged.


9/36

7

4. Introduction

The MAGINON WK 3 HD is a wildlife and surveillance camera with a 3 zone infrared sensor. The sensorcan detect sudden changes to the ambient temperature within an evaluation area. The signals of the

highly sensitive infrared sensor (PIR, passive infrared sensor) switch on the camera, activating picture

or video mode.

Features of MAGINON WK 3 HD Wildlife Camera:

5 mega pixels CMOS sensor.

During day, sharp and clear colour images and during night-time clear black and white images.

Extremely low power consumption in standby operation providing extremely long operating times

(in standby mode up to 3 months when using 4 AA batteries and up to 6 month with 8 AA batteries)

The unique sensor design offers a wider angle of detection and improves the response time of the

camera.

Possible use under extreme temperatures of between -20 C to 60 C.

Compact size (approx. 13.5 x 9.3 x 7.2 cm). Ideally suited for covered use.

Impressively quick shutter release time (1.0 seconds).

Spray water protected according to standard IP54.

The easy to operate securing strap allows quick assembly and alignment of camera.

Using the serial number function, locations can be encoded on photos. Where several cameras are

used, this function allows easier identification of locations when viewing photos.

Date, time, temperature and moon phase can be displayed on the images.

Lockable and password protection.

Alarm in case of low battery level.

Areas of application Camera trap for hunting.

Animal or incident observation.

Motion-triggered security camera for domestic, office or public use.

Any internal and external surveillance, where evidence of an infringement has to be provided.


10/36

8

5. Your camera

5.1. Front view

LED infrared

light

Light sensor

Motion indicator,blue and red LEDs

Central

sensor zone

Lens

Microphone

Side sensor zones (Passive

infrared sensors, PIR)

Locking hole

for lock

Locking bracket

Locking bracket


11/36

9

5.2. Inside views

The monitoris only switched on in the Test mode for changing menu settings or viewing existing

photos.

Using the operating buttons, menu settings can be changed in the test mode or existing photos

can be played back.

An SD or SDHC memory card must have been inserted into the memory card slotin order to savephotos and videos.

Using the mini-USB/TV connection(USB 2.0), the camera can be connected to a computer, in order

to download photos and videos or to connect to a TV set.

Using the mode switchthe three operating modes OFF, TEST and ON can be selected.

Monitor

Operating

buttonsSpeaker

Locking hole

for lock

Memory card

compartment Mini-USB /TV connection

Mode switch (OFF/

Test/ON)


12/36

10

Battery compartment: Insert 4 or 8 type LR6 (AA) batteries as shown. When using 4 batteries,

these can either all be inserted in the top or in the bottom part of the compartment. Othercombinations are not possible.

An external power supply can be provided via the DC connection(input 6 V, at least 1.5 A. Mains

adapter is not included.)

Locking hole

for lock

Locking bracket

Tripod thread

Battery compartment

6V DC connection

Locking bracket


13/36

11

6. Preparing the camera

6.1. Opening and closing the camera

Operating buttons, connections and batteries are located inside the wildlife and surveillance camera.

To open the camera undo the two lateral locking brackets as shown in Fig. 1.

To lock the camera again, engage metal hoops of locking brackets into mount and press down plastic

tab of bracket (Fig.2).

A fixing for a padlock is provided between the two locking brackets, allowing the camera to be securelylocked.

6.2. Inserting the batteries

Open the camera as described in section 6.1 to insert the

batteries. The battery compartment is housed in the right,

rear part of the camera. Now open the protective cover of the

battery compartment by pulling the clamping closure at the

top slightly inwards before lifting off the cover.

First remove any existing batteries from the battery compartment. Insert 4 or 8 fully charge batteries as

shown in the below figure. When inserting batteries ensure correct position as marked for each battery

in the battery compartment.

Fig. 1. Fig. 2.


14/36

12

When using 4 batteries, these can either all be inserted in the top or in the bottom part of the

compartment. Other combinations are not possible.

Close the battery compartment again with the protective cover.

6.3. Inserting the memory card

A memory card must have been inserted in order to save photos and videos. Insert a SD-/SDHC memory

card in the memory card compartment before switching on the camera.

Switch off the camera and open as described in section 6.1.

Note:

Instead of type LR6 (AA) batteries, rechargeable batteries with the same specification (with

2000 mAh or higher) may be used. We recommend NiMh batteries with low self discharge

(not supplied).

An alarm is sounded if battery charge is too low.


15/36

13

Prior to inserting the memory card ensure that

the lateral write-protection on the memory

card has not been activated (see figure).

If the camera displays Card protected, remove

the memory card and change the position of

the memory protection.

Insert the memory card as shown in the adja-

cent illustration. Push the memory card into

compartment until it clicks into place.

To remove the memory card push card in againuntil it is partly ejected.

6.4. External power supply

The camera can be operated using power from an

external power supply. A 6 V power supply with at

least 1.5 A is required containing a connector with

a 3.5 mm external and 1.35 mm internal diameter

(internal plus pole, external minus pole).

Rechargeable batteries cannot be recharged in the

camera using an external power supply.

Note:

SD-/SDHC memory cards up to a capacity of 32 GB are supported.

Write Protection Write Protection

lockedunlocked


16/36

14

6.5. Assembly with strap

Use the securing strap supplied to attach the wildlife camera to a tree or another object. Theillustrations below demonstrate how to fasten the securing strap.

Position the wildlife camera as desired and pull the loose end of the securing strap tight until the

camera is firmly secured.

To release the securing strap again, pull at the tab of the securing strap.

6.6. Using the wall mount

Using the supplied wall mount, the camera can be

securely attached to walls or ceilings. Prior to installing

the wall mount ensure that all existing bolts are securely

tightened.

(A) Drilled holes

(B) Tripod bolt

(C) Counter screw

(D) Hinge screwsA

B C

D


17/36

15

First mark the holes to be drilled (A), by holding the base of the wall fixing against the desired place of

installation. When installing on stone or concrete surfaces use a 6 mm masonry drill. After drilling the

holes insert the supplied wall plugs into the holes so that they are flush with the surface. Next secure

the stand using screws from the assembly kit.

Note that prior to installing the wildlife camera on the wall mounting a memory card or batteries

should be inserted or the power supply should be connected. The camera should also be switched to

Standby mode.Next place the wildlife camera onto the tripod bolt (B) and partly secure the camera (approx. 3 turns).

Turn the camera to the desired alignment and secure with the counter screws(C).

In order to move the camera into the final position, release the two hinge screws (D) slightly, align the

camera and fix the position by tightening the two hinge screws (D).

Note:

Prior to drilling check that no supply pipes are concealed in the wall!


18/36

16

7. Using the camera

Prior to setting up the camera for surveillance, it must be set up for the respective purpose. For thispurpose, the so-called test mode is available. In addition to changing settings, photos and videos can

be taken and existing photos can be viewed in this mode.

7.1. Mode switch

Open the camera as described in section 6.1. The Mode switch is located at the bottom edge on the left

inside. 3 operating modes can be selected:

OFF:The camera is completely switched off in the OFF mode.

TEST: Select TEST mode to adjust settings and make orplayback photos and videos.

ON: The camera is activated to take photos automatically

(Live mode).

7.2. Operating buttons

Set the mode switch to TEST and the camera and monitor are switched on.

Using the operating buttons different functions can now be activated and settings can be changed. For

this purpose, the following operating buttons are provided on the display panel:


19/36

17

Functions of operating buttons in recording mode

Below, the operating buttons are described in the recording mode with non activated menu. MENU: Open the Settings menu using the MENU button.

REPLAY: Press this button to start the replay mode.

: Change to the manual recording mode for video recordings

: Change to the manual recording mode for taking photos.

SHOT: Manually take a video or photo depending on the set recording mode. Video recordings are

also ended by pressing the SHOTbutton.

OK,,: No function (in recording mode).

Functions of operating buttons in replay mode

Below, the operating buttons are described in the replay mode with non activated menu.

MENU: Select the Replay menu using the MENU button.

REPLAY: Press the button to return to Recording mode.

: View existing pictures backwards.

: View existing pictures forwards.

: Enlarge photos in increments (up to 16 times).

: Decrease enlarged photos in increments

OK: Start and end replay of videos.

SHOT: No function (in Replay mode).

Functions of operating buttons in menu

Below, the operating buttons are described in the replay mode with activated menu. (Recording and

Replay mode).

MENU: Close the Main menu or any sub menu by pressing the MENU button.

: Move up one menu point or increment value by 1.

: Move down one menu point or decrease value by 1.

: Enlarge displayed photos in increments (up to 16x).

: Decrease enlarged photos in increments.


20/36

18

OK: Open selected options or accept selected settings.

Confirm each change to a setting by pressing OK. If the change is not confirmed by pressing the

OKbutton, the new settings are lost when leaving the menu.

SHOT, REPLAY: No function (in Replay mode).

7.3. Settings

Prior to using the MAGINON WK 3 HD, change the settings as required.

Slide the mode switch of the wildlife camera to the TEST positi-

on to start the test mode. In the Photo or Video mode press the

MENU button to call up the menu.

All menu options of the MAGINON WK 3 HD and possible

setting values for theRecording modeare listed below. The

standard setting is always highlighted in bold.

Mode: Photo, Video, photo + video

Select whether photos or videos should be taken when motion is detected. When in the Photo +

Video mode, the camera first takes a set number of photos prior to recording a video.

Image size: 12M (4000 x 3000), 8M (3264 x 2448), 5M(2592 x 1944)

Select the desired resolution for photos. We recommend the resolution 5M.A higher resolution produces a somewhat better photo quality but results in larger files requiring

more space on the memory card. 12M and 8M resolutions are generated by interpolation which can

also affect quality.

Video size: 1080P (1920 x 1080, 15 fps), 720P(1080 x 720, 30 fps), WVGA (848 x 480, 30 fps),

VGA (640 x 480, 30 fps)

Select the required video resolution.

A higher resolution produces higher quality videos but results in larger files requiring more space

on the memory card. Videos are recorded in AVI format which can be played back on mot video

equipment.

Number: 1 photo, 2 photos, 3 photos

Select the number of photos to be taken in succession when the camera is triggered in the Photo

mode. Please also observe the parameter Interval!


21/36

19

Length of video: 10 sec(onds), optional 1 - 60 seconds and 3, 5 and 10 minutes

Specify the duration of a video recording when the camera is triggered automatically. The recording

period for videos is not limited in the Test mode.

Interval: 1 min(ute), optional from 0 seconds to 60 minutes

Select the shortest period for the camera to wait before it reacts to the successive triggering of the

main sensor after an animal has first been detected.. The camera does not record any images or

videos during the selected interval. This prevents the memory card from being filled with

unnecessary shots.

Time stamp: On/Off (only available for photos, not for videos)

Select ON to print the date, time, temperature and moon phase on each photo. Otherwise select

Off.

Timer: Off/On

Set timer to On if camera should only be active within a certain time. Once On has been

confirmed with the OK button, the start and end time can be set.

If the start time is, for instance set to 18:35 hrs and the end time to 8:25 hrs, the camera will be

operational from 6:35 pm of the current day until 8:25 am of the following day. The camera will not

be triggered and will not take any photos or videos outside of this period.

Password: Off/On

After selecting On enter a four-digit password to protect your camera against unauthorised access.

This password must be entered each time the camera is switched on in the Test mode before the

camera can be used.

If you have forgotten your password and are unable to use your wildlife camera, the camera and till

receipt must be returned to our Service department. This is the only way to prevent unauthorised access

to your camera.

Serial no.: Off/On (can only be used for photos not for videos)

Select On to assign a serial number to the camera. As soon as On has been confirmed by pressing

the OKbutton, the individual serial number can be inserted.You can use a combination of 4 digits and letters to document the location on the photos (e.g. YSP1

for Yellow Stone Park). When using several cameras this makes it easier to identify the location

when viewing photos.


22/36

20

Time lapse: Off/On

When On has been selected, the camera automatically takes photos or videos in the selected time

interval, irrespective of whether or not the PIR sensor has detected a motion or not. This is useful for

observing cold blooded animals e.g. snakes or plants opening up, etc.

As soon as the On setting has been confirmed by pressing the OKbutton, you can enter the

interval time after which photos and videos are to be taken.

Side PIR: Off/On

The two side PIR sensor zones provide a wide detection angle and detect more potential triggers.

Sometimes you only wish to observe a certain point.

Too many irrelevant triggers from the side sensor zones outside of this point continuously switch the

camera on and off, considerably affecting battery life. In some situations it may be difficult toremove interfering branches or avoid sun light. In these situations you can switch of the side sensor

zones.

Energy saving mode: Off/On

The Energy saving mode comes into effect when battery power is low. When the mode is activated,

the camera automatically reduces the brightness of the IR lights, in order to extend battery life.

Language: Select the desired menu language.

The following languages are available: English, German, Danish, French, Italian, Dutch, Spanish,

Hungarian, Slovenian, Portuguese, Chinese.

Formatting: No/Yes

All files are deleted by formatting the memory card. Press OKbutton and confirm formatting by

selecting Yes.

We recommend formatting the memory card if it has already been used in other devices or if it is a

new card.

Caution: Ensure that files still required have been backed up prior to formatting!

Setting the time: Set date and time.

Press OKbutton to set date and time. Using theandbuttons to skip between values andchange selected values by pressing theandbuttons. Confirm your setting by pressing the

OKbutton.

Default settings:No/Yes

Press Yes to reset the camera settings to the default values and confirm the selection by pressing

the OKbutton.


23/36

21

Auto switch-off: 3 min/5 min/10 min/Off

With this function you can determine whether the camera should be automatically switched off

when not used for some time in the test mode. Set the time after which the camera should be

switched off in the test mode or deactivate automatic switch-off by selecting Off.

The camera can be switched on again by pressing any operating button.

Recording volume: Low/Normal/High

Select with which volume audio recordings are to be recorded.

Playback volume: Low/Normal/High

Select with which volume audio recordings are to be played back.

System: There are two available options:FW Update: If the memory card contains new Firmware this can be installed by confirming the

option by pressing the OKbutton.

During the update the respective status is shown on the display.

FW Version: Shows the Firmware version installed on the camera.

In Replay modethe option Deleteis available in the menu.

Delete: Select the Delete option to remove individual or all photos from the memory card thus

making storage room for new photos.

Single: Using this option you can delete individual photos. After selection the option by pressing

the OKbutton, the photo to be deleted is shown. You can toggle between photos using the

buttons and . As soon as the deletion of a photo has been confirmed by pressing Yes, the photo

is deleted and the next photo is displayed To end the deletion process, select No and confirm by

pressing OK.

All: Select option All to delete all photos on your memory card. To confirm deletion of all your

photos, select Yes and press the OKbutton. Select No to interrupt the deletion operation.


24/36

22

7.4. Night recording

During night recording the infrared LEDs(IR LEDs) at the front of the wildlife

camera provide the light required for

taking photos.

MAGINON WK 3 HD uses IR LEDs with a

long wavelength, to keep red light to a

minimum. The provided number of IR

LEDs generates a high deflection angle

thus allowing night recording at a distance of 3 m to 20 m, without overexposing the object. Reflectingobjects can, however, also cause overexposure within this range (e.g. road signs).

Please note that night recording using IR LEDs produces black and white images.

7.5. Setting up the live mode

The standard application of the MAGINON WK 3 HD is the so-called Live mode. When in this mode,

photos are either triggered by movement sensors or at intervals according to the respective setting.

To set up the Live mode, switch mode switch to ON position.

The red status LED flashes for approx. 5 seconds after which thecamera operates automatically and enters the Standby mode.

As soon as wild animals or other objects directly enter the

detection area of the central sensor zone, the camera starts to

record photos and videos.

Where wild animals enter the detection range of the side

sensors, the sensors detect the movement and activate the camera. As soon as the wild animals move

further into the detection range of the central sensor zone, the camera starts to take photos/videos.

Where after movement has been detected by the side sensors no further movement is detected for fiveminutes, the camera returns to its Standby mode.


25/36

23

Advantages of PIR sensors (Passive Infrared Sensors)

In order to save on battery power, an infrared camera is normally in Standby mode in which only themain sensor is active. As soon as the central sensor zone detects wild animals, the camera is switched

on and starts taking photos. The time between the activation and the start of shooting is referred to as

triggering time.

Where wild animals do, however, move past the camera swiftly, it is possible that the photo only shows

the rear part of the body or possibly nothing at all. The MAGINON WK 3 HD solves this problem due to

the unique design of the lateral PIR sensor zone. The combination of the two lateral sensor zones and

central sensor zone produces a 100-120 induction angle, by far exceeding the angle of an individual

sensor.

Where wild animals first pass through the detection range of the side PIR sensor zone, the camera is

activated and is ready to start shooting after 1.0 seconds. Where the wild animal then slowly enters the

detection range of the central sensor, the camera starts shooting and thus records the entire body of

the animal. This process takes approx. 0.2 seconds.

Where the wild animal remains only within the detection range of the side sensor zones, the system is

designed as follows to prevent the permanent supply of power to the camera:

Where the wild animal does not enter the detection range of the central sensor zone and thus does not

trigger the sensor, the camera returns to the Standby mode after 5 minutes. Where triggering incidentsoccur twice in succession only within the detection range of the side sensor zone, the camera is not

activated by the side sensor zone but only by the central sensor zone. At a later stage when the wild

animal finally enters the detection range of the central sensor zone and does not move rapidly, the

photo based on the standard reaction time of one second will probably capture the entire body of

the animal.

7.6. Aligning the camera

The Test mode is advantageous for determining the best possible detection angle and range of the

movement sensor. For this purpose attach the camera at approx. 1-2 m height to a tree and align thecamera with a desired direction.

Move slowly from one side of the observed area to the other. Move parallel to the camera Try out

different angles and distances.

The blue LED on the front of the camera indicates that you were detected by a side sensor zone.

The red LED on the front of the camera indicates that you were detected by a central sensor zone.


26/36

24

In this way you can determine the best position for aligning the camera.The LED only lights up in the Test mode as soon as one of the sensors has detected movement. The LEDs

do not light up when in Live mode.

In order to prevent incorrect signals and unnecessary photos, we recommend not using the camera at

sunny points and check that no branches are in the active area of the sensor. Optimum alignment is

in North or South direction. The detection range of the sensors is approx. 100 to 120, the detection

range of the lens is approx. 40.

Also check that the camera is set to the correct height in line with the point to be observed. Where

necessary, point the camera down for optimum alignment.

7.7. File format

The wildlife camera stores photos and videos on the memory card in the folder \DCIM\100MEDIA.Photos are given a file name with extension JPG (Example: SUNP0001.JPG), videos are given the

extension .AVI (Example: SUNP0002.AVI).

When in TEST and OFF mode use the enclosed USB cable to transfer files onto the computer.

Alternatively you can insert the memory card in a card reader on the computer.

The video files can be played with most standard programs, such as Windows Media Player, QuickTime

etc.

Note:

MAGINON WK 3 HD corresponds to protection class IP 54. The camera is protected against

dust and spray water and can thus be used in any weather condition.

Blue LED

Red LED


27/36

25

8. Connecting to computer and TV

The wildlife camera can be connected to a computer or your TV using the supplied USB and video cablesto view existing photos/videos.

8.1. Connection to computer

System requirements

Windows Macintosh

Pentium III or higher

Windows XP/Vista/7/8

512 MB RAM

1GB available hard disk space

Screen resolution 1.024 x 768 or higher

Available USB connection

PowerPC G3/G4/G5

OS 10.3.9 or newer system

512 MB RAM

1GB available hard disk space

Screen resolution 1.024 x 768 or higher

Available USB connection

1. Connect the camera to your computer using the USB cable.

2. The camera switches on automatically in the USBmode, irrespective of the selection on the Mode

switch.

3. The camera installs itself on the Computer as an

additional drive under the name Removable storage

device.

4. Double click on the device to detect the folder DCIM.

5. The photos and videos are located in the sub-folders of the DCIM folder.

6. You can copy or move photo and video files on the computer.

Alternatively you can insert the memory card in a card reader on the computer.

Note:

Mac computers show an Unknown drive on the desktop. When clicking on this drive, the

program iPhoto is automatically started.


28/36

26

8.2. Connection to TV

1. Switch on the wildlife camera in Test mode.2. Connect the video cable to the camera.

3. Plug the other end of the video cable into the TV.

Connect the yellow connector to the video input and the white connector to one of the audio inputs

of the TV.

4. Set the video input source of the TV to the video input used.

V R L

S HO T

OK

MENU

R E P L A Y

Audio(white)

Video(yellow)

AV Mode

Note:

When the camera is connected to the TV, the LCD screen of the camera is switched off

automatically. The screen controls of the TV are then used.


29/36

27

9. Technical specification

Note:

Design und Technical specification are subject to change.

Element Description

Image sensor 5.0 mega pixels, 1/2.5 CMOS sensor

Photo resolution12M: 4000 x 3000 (interpolated); 8M: 3264 x 2448 (interpolated);

5M: 2592 x 1944

Screen 6.1 cm (2.4") colour TFT-LCD; 480 x 234 pixels

Recording medium Supports SD/SDHC-memory cards up to 32 GB (optional)

Video resolutions1920 x 1080 (15 fps), 1280 x 720 (30 fps),

848 x 480 (30 fps), 640 x 480 (30 fps)

Lens F= 7.45; F/NO = 3.0; FOV=55; Auto IR filter

Effectiveness Daytime: 1 m infinitive; Night time: 3 m 20 m

Triggering distance up to 20 metres

Triggering time 1.0 seconds

Range of IR flash 20 m

Detection angle of sensors Central sensor zone: 35 - 40; Side sensor zone: each 30

Spray-water protected Yes (IP protection class54)

Storage formats Photo: JPEG; Video: AVI Motion JPEG

Connections Mini USB 2.0 (USB and TV Out)

Power supply

4x or 8x batteries type LR6 (AA);

4 x or 8x NiMH batteries type LR6 (AA) with low self-discharge;

external 6V power supply, at least 1.5 A (not supplied)

Standby time approx. 6 months (with 8 batteries)

Dimensions approx. 135 (H) x 93 (B) x 72 (T) mm


30/36

28

10. System information, Maintenance and Disposal

Trademark information

Microsoft and Windows are trademarks of Microsoft Corporation registered in the US.

Pentium is a registered trademark of Intel Corporation.

Macintosh is a trademark of Apple Computer Inc.

SD is a trademark.

Other names and products can be trademarks or registered trademarks of the respective owners.

10.1. CareDo not use any corrosive cleaners, such as methylated spirits, thinners, etc. to clean the camera housing

and supplied accessory. When required, the clean system components with a soft dry cloth.

10.2. Storage

Always remove the battery from the housing if the camera is not being used for some time and store

the battery separately. On a day-to-day basis and over longer periods the batteries can be kept at a dry

location out of the reach of children.

10.3. Disposal

For disposal, separate packaging into different types and dispose of in line with

environmental regulations in supplied collection containers. Batteries and storage

batteries may not be disposed of in domestic waste. Consumers are obliged by law

to return used batteries to communal collection points or dealers selling batteries.

Storage batteries and batteries do therefore contain the adjacent symbol.

Correct disposal of product:

The adjacent symbol indicates that electrical and electronicequipment may not be disposed of in domestic waste in the EU.

Please use the returns and collection points of your local council or

contact your dealer you purchased the product from. This prevents

potentially harmful effects on the environment and health as a

result of incorrect disposal. For further information contact the

respective department of your local council.

www.recyclenow.com

Visit www.recyclenow.com to see

which items are collected in your area.

BOX &INNER BOX

CARDwidely

recycled

BAGSFILM &

PLASTICnot currently

recycled


31/36

29

11. Potential legal infringements

Using the Wildlife Camera you should note the following:

Copyright

Generally every person owns his/her own image. According to the copyright law, images may only be

published without the consent of the respective person if the person appears only as a person

embellishment to a landscape image, or a location as a public place. The answer to the question of

whether a person is embellished depends on the individual circumstances. For reasons of legal

certainty the presence of the wildlife camera should be pointed out in all situations in which persons

could be identified from photos (see also section Duty of notification).

Protection of privacy

Shown images may not infringe the privacy of others. Do not point camera onto the garden or entrance

door of your neighbour, even if these locations are visible from your known home or public locations.

This does not entitle you to publish respective photos or videos.

Personal determinability

Personal determinability exists, where it can be determined that a certain person was at a certain place

at a certain time. The person can also be identified by a personal identifier such as a vehicle registrationplate. Personal determinability of persons must be absolutely avoided.

Surveillance cameras at the place of work

Employers should not use surveillance cameras at the place of work unless potential legal infringe-

ments can be fully excluded.

Traffic surveillance cameras

When using surveillance cameras facing traffic, it is recommended to configure the location and view

of the camera in such a way that road users are identifiable from any images through a vehicle

registration plate. Road users could also be determined from lettering on vehicles.


32/36

30

Duty of notification

Where a personal identification of persons cannot be excluded, a clearly visible notice concerningthe surveillance camera must be erected at all accesses to the monitored area. Passers-by must also

be informed that by entering the monitored area they give their permission to pictures/videos being

taken so that if they do not wish to give their consent they can avoid the picture/video being taken by

not accessing the area. The voluntary nature of the declaration must be observed. If the camera trap is

located at a point persons have to pass to reach their destination (e.g. entrance of a sight), no consent is

deemed to have been given as no voluntary nature applies.

12. Warranty and Service

Our service outlets will be happy to assist you in case of problems with the operation of the device or

with any queries and problems. The device comes with a 3-year manufacturers warranty. Please see

the enclosed Warranty Card for details.

Please contact our hotline prior to returning a defective device.

13. Conformity

The Manufacturer hereby declares that the CE marking was applied to the product in accordance with

the basic requirements and other relevant provisions of the following European

Directives:

2011/65/EC RoHs Directive

2004/108/EC EMC Directive

The EC Declaration of Conformity can be requested from the address specified on the Warranty card.

Service address:

Sertronics LTD

MAGINON Service

45 Regal Drive, Walsall Enterprise ParkWalsall, WS2 9HQ

United Kingdom

Phone: 00 800 - 78 77 23 68

Manufacturer's address:

supra

Foto-Elektronik-Vertriebs-GmbH

Denisstr. 28A67663 Kaiserslautern

Germany


33/36

31

14. Index

AAccessories 1

Aligning the camera 23

Areas of application 7

Automatic switch-off 21

B

Batteries

Insert 11

BatteryType 12

Battery compartment 10

C

Care 28

Closing 11

Conformity 30

Connection

Computer 25

TV 26

Contents of box 1

D

Date 20

DC connection 10

Default settings: 20

Delete 21

Disposal 28

F

Features 7

File format 24

Files 24

FirmwareUpdate 21

Version 21

Front view 8

H

Hazard information 4

I

Image size 18, 27

Inside view 9

Interval 19

L

Language 20

Legal infringements 29

Lens 27

Live mode 16, 22

Locking 11M

Memory card

Format 20

Insert 12

Protect 13

Memory card compartment 9

Memory cards 27

Mini USB port 9Mode 18

Mode switch 9, 16

Monitor 9

Motion display 23


34/36

32

N

Night recording 22Number of photos 18

O

Opening the camera 11

Operating buttons 9, 16, 17

P

Password 19

Periodic recording 20

PIR sensors 23

Power-saving mode 20

Power supply 13, 27

External 13

Protective cover 11

R

Recording mode 18

Replay mode 21

S

Safety information 4

Securing strap 14

Serial number 19

Service 30

Side PIR 20

Spray water protection 24, 27

Storage 28System requirements 25

T

Test mode 16, 18

Time 20

Timer 19

Time setting 20

Time stamp 19

Trademarks 28

Tripod thread 9

TV connection 9

U

USB cable 25

V

Video cable 26

Video length 19

Video size 18, 27Volume 21

W

Wall fixing 14

Warning notices 4

Warranty 30


35/36


36/36

supra

Foto-Elektronik-Vertriebs-GmbH

Denisstr. 28A

67663 Kaiserslautern

Germany

91631

06/2014

2001 6104

Maginon Wk3 Hd Bda Uk description

Documents

Transcript of Maginon Wk3 Hd Bda Uk description