Made in Germany EBA - · PDF fileEBA 430 E • EBA 430 EP-3-EBA 430 E • EBA 430...

download Made in Germany EBA - · PDF fileEBA 430 E • EBA 430 EP-3-EBA 430 E • EBA 430 EP-2-Dear customer, Thank you for choosing a paper cutting machine from EBA. With the purchase of

If you can't read please download the document

  • date post

    04-Jul-2018
  • Category

    Documents

  • view

    227
  • download

    3

Embed Size (px)

Transcript of Made in Germany EBA - · PDF fileEBA 430 E • EBA 430 EP-3-EBA 430 E • EBA 430...

  • EBA 430 EEBA 430 EP

    EBA Made in Germany

    EBA Krug & Priester 72336 Balingen Germany www.eba.de

    Document Shredders

    Trimmers and Guillotines

    Operating Instructions

    Prin

    ted

    in G

    erm

    any

    E

    BA

    04/

    2002

    D

    Prin

    ted

    in G

    erm

    any

    E

    BA

    04/

    2002

    D

  • EBA 430 E EBA 430 EP

    -3-

    EBA 430 E EBA 430 EP

    -2-

    Dear customer,Thank you for choosing a paper cutting machine from EBA. With the purchase of thisquality product you can be sure you have made a good choice.

    Please read these operating instructions before putting the machine into operationand observe the safety regulations.

    Read through the operating instructionscarefully

    Table of contents

    PagesSafety precautions 4 11Installation 12 13Operation 14 25Blade replacement 26 34Maintenance and cleaning 35 36Possible malfunctions 37 42Accessories 43Manufacturers Declaration 45

  • EBA 430 E EBA 430 EP

    -3-

    EBA 430 E EBA 430 EP

    -2-

    Dear customer,Thank you for choosing a paper cutting machine from EBA. With the purchase of thisquality product you can be sure you have made a good choice.

    Please read these operating instructions before putting the machine into operationand observe the safety regulations.

    Read through the operating instructionscarefully

    Table of contents

    PagesSafety precautions 4 11Installation 12 13Operation 14 25Blade replacement 26 34Maintenance and cleaning 35 36Possible malfunctions 37 42Accessories 43Manufacturers Declaration 45

  • EBA 430 E EBA 430 EP

    -5--4-

    Children must not operate the machine!

    Do not cut hard materials or materials whichmay splinter!

    The machine must not be located outside!

    The machine must be installed on a sturdy, dryand level floor!

    Do not use in the vicinity of inflammableliquids or gases!

    Paper clips or hard material will damage thecutting blade!

  • EBA 430 E EBA 430 EP

    -5--4-

    Children must not operate the machine!

    Do not cut hard materials or materials whichmay splinter!

    The machine must not be located outside!

    The machine must be installed on a sturdy, dryand level floor!

    Do not use in the vicinity of inflammableliquids or gases!

    Paper clips or hard material will damage thecutting blade!

  • EBA 430 E EBA 430 EP

    -7--6-

    Never leave the blade unattended. Do notdismount or transport the blade withoutprotection!Risk of injury!

    The machine may only be used for cutting paper or similar materials!

    This machine is only constructed for "one-manoperation"!

    Disconnect from the mains before starting anyservice work or before removing the panels!

    Replacement of blade and cutting stick mayonly be performed when the main switch isswitched off!

  • EBA 430 E EBA 430 EP

    -7--6-

    Never leave the blade unattended. Do notdismount or transport the blade withoutprotection!Risk of injury!

    The machine may only be used for cutting paper or similar materials!

    This machine is only constructed for "one-manoperation"!

    Disconnect from the mains before starting anyservice work or before removing the panels!

    Replacement of blade and cutting stick mayonly be performed when the main switch isswitched off!

  • EBA 430 E EBA 430 EP

    BA

    BC

    A

    15mm0.59inch

    -9--8-

    A

    AA

    B

    A CC

    Operating the machine without safety device(front safety guard (A), rear screwed safetyguard (B) and panel (C) is forbidden!

    The dangerous cutting movement issafeguarded by a movable guard (A) and asafety two-handed control system! (B)

    Before working with the machine and afterevery blade replacement the automatic cut-offfunction of safety guard (A),(correct if distancebetween cover and table is < 15 mm) mainswitch (B) and control panel (C) must bechecked.

    All components which may endanger theoperator are covered by a guard!

  • EBA 430 E EBA 430 EP

    BA

    BC

    A

    15mm0.59inch

    -9--8-

    A

    AA

    B

    A CC

    Operating the machine without safety device(front safety guard (A), rear screwed safetyguard (B) and panel (C) is forbidden!

    The dangerous cutting movement issafeguarded by a movable guard (A) and asafety two-handed control system! (B)

    Before working with the machine and afterevery blade replacement the automatic cut-offfunction of safety guard (A),(correct if distancebetween cover and table is < 15 mm) mainswitch (B) and control panel (C) must bechecked.

    All components which may endanger theoperator are covered by a guard!

  • EBA 430 E EBA 430 EP

    -11--10-

    230 V / 10A min115 V / 15A min

    Protect mains cable against heat, oil andsharp edges!

    Connect the power cord to a single phasesocket

    Ensure free access to mains

    When not in use for a longer period switch off.(Main switch to "0").

  • EBA 430 E EBA 430 EP

    -11--10-

    230 V / 10A min115 V / 15A min

    Protect mains cable against heat, oil andsharp edges!

    Connect the power cord to a single phasesocket

    Ensure free access to mains

    When not in use for a longer period switch off.(Main switch to "0").

  • EBA 430 E EBA 430 EP

    -13-

    C

    A

    B

    -12-

    1.

    2.

    3.

    Unpack the cabinet (A), (accessories) or stand(B), (accessories) and assemble accordingto the enclosed separate instructions.

    2 strong people are required to lift themachine onto the cabinet or stand. Beware offingers! Risk of injury!

    Only on EBA 430 EScrew on the backgauge crank (A) andoperating handle (B) (found together withtools in the tool set).

    Plug into socket.

    B

    A

  • EBA 430 E EBA 430 EP

    -13-

    C

    A

    B

    -12-

    1.

    2.

    3.

    Unpack the cabinet (A), (accessories) or stand(B), (accessories) and assemble accordingto the enclosed separate instructions.

    2 strong people are required to lift themachine onto the cabinet or stand. Beware offingers! Risk of injury!

    Only on EBA 430 EScrew on the backgauge crank (A) andoperating handle (B) (found together withtools in the tool set).

    Plug into socket.

    B

    A

  • EBA 430 E EBA 430 EP

    -15-

    B

    AC

    D

    A

    AA

    BB

    C

    D

    -14-

    It is not allowed to operate the machine if theoperating and safety instructions have notbeen understood. Please check the safetydevices upon their function and completenessbefore working with. All covers have to be mounted (A). The release for cutting is allowed only if

    the cover is closed and the two-handsafety device is operated at the same time (B)

    The front cover should not close by itself(otherwise please adjust the hexagonalscrew at the right and left(C). (Remove thecover) (D).

    We recommend to keep a test resultbooklet.

    Position the main switch to "I" (A). Insert thekey for the control system and move it to theright (B). Open the safety guard (C). Themachine is now ready for use.

    Only EBA 430 EPPress S button (D).(Reference point is driven to).

  • EBA 430 E EBA 430 EP

    -15-

    B

    AC

    D

    A

    AA

    BB

    C

    D

    -14-

    It is not allowed to operate the machine if theoperating and safety instructions have notbeen understood. Please check the safetydevices upon their function and completenessbefore working with. All covers have to be mounted (A). The release for cutting is allowed only if

    the cover is closed and the two-handsafety device is operated at the same time (B)

    The front cover should not close by itself(otherwise please adjust the hexagonalscrew at the right and left(C). (Remove thecover) (D).

    We recommend to keep a test resultbooklet.

    Position the main switch to "I" (A). Insert thekey for the control system and move it to theright (B). Open the safety guard (C). Themachine is now ready for use.

    Only EBA 430 EPPress S button (D).(Reference point is driven to).

  • EBA 430 E EBA 430 EP

    B

    C

    A

    EBA 430 E

    EBA 430 EP

    -17--16-

    A

    B

    DE

    EBA 430 E

    EBA 430 EP

    C

    EBA 430 EThe backgauge has to be adjusted by thehandle with calibration ring (A). Measurementhas to be adjusted from the rear.

    EBA 430 EMeasurement is indicated on the back side-lay(A). The fine adjustment is achieved by usingthe calibration ring (B). The scale is divided inmm (One complete turn corresponds 10 mm =1 cm).

    EBA 430 EPThe graduation is done manually via thehandle with calibration ring (B) or byprogramming (C) the cutting measurements.(If Display shows "C" the pressure lever (D)has to be moved to the right, so thebackgauge (E) is moving).

    EBA 430 EPMeasurement is shown in the display of thecontrol device in inches or cm (C).

  • EBA 430 E EBA 430 EP

    B

    C

    A

    EBA 430 E

    EBA 430 EP

    -17--16-

    A

    B

    DE

    EBA 430 E

    EBA 430 EP

    C

    EBA 430 EThe backgauge has to be adjusted by thehandle with calibration ring (A). Measurementhas to be adjusted from the rear.

    EBA 430 EMeasurement is indicated on the back side-lay(A). The fine adjustment is achieved by usingthe calibration ring (B). The scale is divided inmm (One complete turn corresponds 10 mm =1 cm).

    EBA 430 EPThe graduation is done manually via thehandle with calibration ring (B) or byprogramming (C) the cutting measurements.(If Display shows "C" the pressure lever (D)has to be moved to the rig