Macon-Bibb County Government · Macon-Bibb County Government . ... FREESTANDING, MODEL: AH-425,...

Macon-Bibb County Government Procurement Department

Government Center 700 Poplar Street, Suite 308

Macon, Georgia 31201 (478) 803-0550

Fax (478) 751-7252

Chauncey K. Wilmore Senior Procurement Officer

February 20, 2017

ADDENDUM # 5

To: ALL PROSPECTIVE FIRMS

Re: INVITATION FOR BIDS: 17-014-DS, Freedom Park Renovations

The Invitation for Bids, referenced above, is modified as follows: GENERAL:

1. Due to a flurry of questions after the submittal deadline, the client decided to extend the bid. The Freedom Park bid due date is pushed back from 2/15/ 2017 to 2/23/2017 at Noon.

2. All additional questions must be into the city before 5pm Thursday 2/16/2017 to be considered. All

questions after that date will not be considered.

3. The Land Disturbance Permit (LDP) has been approved by the city. Bryan Simpson of Carter Sloope will be the contact for obtaining the permit. (478) 477-4691

4. A copy of bidders sign-in list may be obtained from the Macon Bibb Website.

Click this link to view the bidder’s list: http://www.maconbibb.us/wp-content/uploads/2017/01/Sign-in-Sheets-Freedom-Park.pdf

5. The BID FORM in the ‘Invitation to Bid’ supersedes the Bid Form included in Volume 1. 6. The project is being bid ‘As-Specified’ with no substitutions or As-Equals in the base bid.

Contractors are encouraged to offer As-Equal alternates for any item or product specified for the project. Alternates shall be submitted on the BID ALTERNATES TO BASE BID FORM. See attached Alternates Form in excel format. Contractor shall list alternates in numerical order on the form and provide the corresponding bid item number from the Construction Bid Items Form. The Alternates form shall be attached to the BID FORM that is taken from the Invitation to Bid. Alternates will not be announced at the bid opening. Explanative data for each alternate shall be included in the Bid Package. Alternates #1 and #2 are explained in Addendum #3. Contractors are not required to submit any alternates if they so desire.

http://www.maconbibb.us/wp-content/uploads/2017/01/Sign-in-Sheets-Freedom-Park.pdf

7. This Addendum will constitute the 5th Addendum issued. The attached Addenda Form should be completed and attached to the BID FORM.

PLANTING:

1. Please use the attached Plant List as revised 6/16/17 and discard the previous two (2 )plant lists issued.

2. Turf grass sod and seed were originally specified in the construction documents as Tift 419 Bermuda. As of this addendum, the Tift 419 Bermuda will remain the correct specification and ‘not’ the TiftGrand as shown on Plant List issued 2/14/17.

3. Bids for all growing medium, topsoil placement and soil preparation of the sod areas shall be included under the line item Q. Soil Preparation on the attached Plant List. 2/16/2017

4. All grass areas Inside the field fences and the concession areas will be bid as Sod under line item S. Sod, as identified on the attached Plant List: Rev. 2/16/2017

5. All grass areas Outside the field fences and concession area shall be bid as ‘Seeded’ and are included as part of the cost for erosion control.

6. All soil preparation and soil placement for the seeded areas shall be included in the costs of the erosions control items.

ELECTRICAL;

1. MUSCO Alternates must be submitted on the Alternates Form as attached. A completed Lighting Fixture Schedule for Item #19 for MUSCO fixtures must be included in the bid package.

2. Panel MDPB in the Splash Pad Building shall be changed from a NEMA 1 enclosure to a NEMA 4X stainless steel enclosure.

3. WaterSplash Inc. has included the stainless steel breaker box in the Splash Pad Manual and is part of their equipment installation quote.

4. Client has included a deductive alternate to remove the Sports Lighting (item #19) and the Scoreboards (item #20) from the project. A description of this deduction is described by the Electrical Consultant and is attached to the addendum.

5. Contractor shall not deduct the necessary conduits and routing to allow for installation of the Sports Lighting and scoreboards back to the concessions building. Such necessary conduit as shown on the electrical plans shall remain as part of the base bid.

INFIELD MIX: 1. Note that the Base Line Drain that runs around the outer edge of the base lines is not a blanket

detail over the entire infield. The profile illustrated in detail 4 – BD-1 only occurs over the top of the base line drain profile. See the layout detail 3 C1.2 for the location of the baseline drains. It is designed to be a French drain to keep the wearing area of the field from holding water after a rain. The profile shows the top of the gravel / filter cloth at 8” below the finished surface of the playing field no matter what that surface may be. Therefore the contractor should place enough soil above the filter cloth to meet the bottom of the Infield profile, or the turf grass profile. Therefore the contractor needs to leave a 3” of space above the top of the fill placed over the filter cloth.

2. Sheets BD.1 (Detail 4) and BD.2 (Detail 1) call for a combination of clay and brick dust for the infield mix.

Specifications Section 329210 - ATHLETIC FIELDS CONSTRUCTION, Paragraph 2.1, D. calls for: Infield Mix for Softball Infields and Skinned Areas: Imported “Molena” Infield Mix, comprised of ±83% sand, ±12% silt and ±5% clay or approved equal. Specified contents of mix shall be within plus or minus 2 percent of the percentage specified. These requirements conflict with one another. Contractor shall furnish and install materials in accordance with the Section 329210 Specification, ‘NOT’ the materials noted on the details.

HARDWARE AND FENCING:

1. Items #21C & #22C refer to the backstop height in the dugout area. The backstop is 20’ tall, therefore the backstop fence in front of the dugout will extend an additional 10’ above the dugout fence. See details 4/BD.3 & 3/BD.4 for additional information.

2. All chain-link fencing shall be black vinyl coated. 3. Bid all post sizes as indicated on the details of the drawings. Contractor may offer VE alternatives

with explanations outside his base bid if he so desires. Use the Alternates Form provided. 4. No bottom rail is needed for fences 4’-6’ height. Use 7 gauge tension wire for the bottom of all 4-6’

high fences. 5. No center rail is needed for fences 4’-6’ height. 6. Dugout Bench, Sheet 4. Items 21h and 22h both show the bench length as 21’. The details for

the dugout show the space for the bench as 22’. 7. Detail “PICNIC TABLE” 4a/SD.3 should read as follows (edits are highlighted):

a. “VICTOR STANLEY, INC. ANTHRO SITES COLLECTION Handicap Accessible, 42” PICNIC TABLE WITH HORIZONTAL STEEL SLATS, 5-BACKLESS SEATS, PERFORATED TABLE TOP - ROUND PATTERN, FREESTANDING, MODEL: AH-425, COLOR: POWDER-COATED BLACK. (2) each

b. “VICTOR STANLEY, INC. ANTHRO SITES COLLECTION, 42” PICNIC TABLE WITH HORIZONTAL STEEL SLATS, 6 BACKLESS SEATS, PERFORATED TABLE TOP - ROUND PATTERN, , FREESTANDING, MODEL: A-426, COLOR: POWDER-COATED BLACK. (8) each

IRRIGATION:

1. In planted areas where no irrigation is shown, the contractor is expected to water and warranty the grass and plant materials until final acceptance by the owner.

2. Booster Pump alternate or substitute: Bid the existing specifications as shown as the base bid. If the contractor desires to submit an alternate or substitute for the booster pump he may do so under the following criteria:

a. Must first bid what is specified as the base bid. b. May offer a substitute or alternate on the Bid Alternate Form. c. Contractor will need to provide very detailed information about the substitute. d. Information to include engineered details, product sheets and data that is project specific. e. Need to submit a detailed list from the manufacturer as to what is different between

specified unit and substitute. f. A simple same gpm/psi substitute is not the only factor required, must submit quality

items/functions for review. g. The pump will have to be a prefabricated unit, not stick built by the contractor.

ARCHITECTURE:

1. Corrected Structural Plans are attached. There was a glitch in the printing that removed some inportant information.

2. Stucco on wall detail 6/SD3 is an error. Disregard stucco. Use detail 12/SD3 for face finish of the site retaining walls.

3. Detail 5 sheet SD2 – (38) is not to be a retaining wall but should be a freestanding seatwall. No need for the gravel and fill behind the wall, see the site plan.

4. Asphalt Roofing Shingles: Use 30lb Felt when roof slope is greater than 3/12. Ice and Water Shield would only be required for the underlayment at the asphalt shingle roofing when slope is less than 3/12

5. The GAF Timberline HD shingle is to be used as the basis of design. 6. The use of nail guns for the installation of the asphalt shingle roofing is acceptable. 7. For gutters and downspouts use Kynar coated metal with minimum thicknesses as specified in

Sheet Metal, Flashing and Trim section 07 2600 paragraph 2.1-A . 8. The TPO roofing shall be ‘fully adhered’ to substrates as described in the specifications. 9. Rigid insulation is not required at the application. The plywood above the corrugated metal

deck at the open canopy serves the same purpose as the 1/4” cover board. The TPO roofing is to be adhered directly to the concrete topping slab over the precast concrete planks at that application.

10. Fire Extinguishers: Provide one fire extinguisher with a wall mounted clip at the following locations:

Concession Building: Kitchen adjacent to door C105 2nd Floor at pier in middle of room Splash Pad Building Staff Office 103 to left of window opening Utility Room S101 to right of double doors

11. Q: Concession Building indicated R-19, FSK Foil Faced Batt Insulation. Is this correct or should it be R-30 and is it Foil-Faced. A: Install as specified.

12. Q: Concession Building indicated R-11 Batt Insulation in the walls. Is this correct? A: Yes, install R11 batt insulation at Concession Building walls.

13. Q: Splash Pad Building does not indicate any insulation is required. Is this correct? A: There is no insulation at the Splash Pad Building. 14. Q. Does the general contractor include the splash pad in his bid:

A. General contractor shall bid the splashpad as designed and specified by WaterSplash in the base bid.

B. Any variations or substitutions to the design or specifications may be included as a contractor’s recommended alternate to the bid.

C. Alternate shall be submitted on the Alternates Form.

Please incorporate this change into the Invitation for Bid and acknowledge receipt of this addendum on your bid form.

Sincerely,

Desmond R. Schneider Desmond R. Schneider Procurement Officer I

FREEDOM PARK GIRLS SOFTBALL FIELDS MACON BIBB PARKS AND RECREATION ADDENDA TO THE CONSTUCTION BID DOCUMENTS: Macon Bibb Purchasing Department has issued the following addendum for the above referenced project. These addendum are posted on the Macon Bibb Website or are available by contacting Desmond Schneider at the Macon Bibb Purchasing Department.

[email protected] (478) 803-0537.

Addendum # 1 ___________ Addendum # 2 ___________ Addendum # 3 ___________ Addendum # 4 ___________ Addendum # 5 ___________ Contractor shall initial each of the above stated Addendum to acknowledge that the addendum have been received and incorporated into the Construction Bid Documents for the Freedom Park Girls Softball Fields and reflected in their Base Bid. Please attach this acknowledgement form to the BID FORM that is included in the ‘Invitation to Bid’ for the above referenced project. February 17, 2017

mailto:[email protected]

Plant List Revised 2017_02_16 Page 1 of 1

Rev. 2/16 /2017

# Description Qty. Size Price TotalA Carpinus caroliniana

American HornbeamB Magnolia macrophylla

Bigleaf MagnoliaC Ulmus parvifolia 'Emer II' Allee

Allee Chinese ElmD Lagerstromia indica x fauriei 'Natchez'

Natchez CrapemyrtleE Quercus myrsinifolia

Chinese Evergreen OakF Fraxinus pennsylvanica 'Marshall's Seedless'

Marshall's Seedless Green AshG Gleditsia triacanthos

Honey LocustH Quercus nutallii

Nuttall OakI Magnolia virginiana

Sweetbay MagnoliaJ Quercus phellos Hightower P.P. #13677

Hightower Willow OakK Japanese Cleyera

Cleyera japonicaL Camellia sasanqua 'ShiShi Gashira'

Shishi Gashira CamelliaM Azalea indica 'Formosa'

Formosa AzaleaN Osmanthus fragrans

Tea OliveO Gardenia jaminoides ' Radicans'

Dwarf GardeniaP Liriope muscari 'Big Blue'

Big Blue LiriopeQ Soil preparation 1 job $0.00 $0.00R Mulch 3" deep ( aged hardwood ) 1 job $0.00 $0.00

SSod -Tiftway 419 (fields, concessions area, areas indicated on erosion plans)

301,500 SF $0.00 $0.00

T Seeded areas ( included in erosion contol costs X X XTOTAL Transfer to item #28 on the Construction Bid Items Schedule $0.00

Revised 2/14 / 2017

16

1

3

21

11

43

430

16

9

6

7

3

18

2-1/2"

2-1/2"

10

18

12 7 Gal.

2-1/2"

4"

2-1/2"

1"/ea.

2-1/2"

1 Gal.

4" Pot

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

2-1/2"

1"/ea.

4"

5 Gal.

5 Gal.

3 Gal.

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

THIS SPREADSHEET IS AVAILABLE IN ELECTRONIC (EXCEL) FORMAT BY CONTACTING BRYON MACCAULEY AT [email protected]

# 28 Plant List

Freedom Park Girls Softball Fields

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

$0.00

3.2' TYP 3'-0" TYP

3.2' TYP 3'-0" TYP

4317 Park Drive, Suite 400

Norcross, Georgia 30093

(770) 416-7511

www.mackcain.com

This drawing is the property of Mack Cain

Design Studio and Travis Pruitt &

Associates, Inc. It is only to be used for the

project and location identified herein. No part

of this drawing may be reproduced, stored, or

transmitted in any form by means electronic,

mechanical photocopying, or otherwise without

prior written consent.

DESIGNED BY:

DRAWN BY:

CHECKED BY:

APPROVED BY:

PROJECT NO.

SHEET

SCALE:

DATE:

RE

LE

AS

ED

F

OR

C

ON

ST

RU

CT

IO

N

150536

No. Date

Mack Cain Design Studio

@Travis Pruitt & Associates

3301 R

OF

F A

VE

NU

E

MA

CO

N, G

A 31204

09/30/16

HJ

BCR

HJ

HJ

07/18/16 PROGRESS SET

4317 Park Drive, Suite 400Norcross, Georgia 30093

Phone: (770)416-7511Fax: (770)416-6759

www.travispruitt.com

Travis PruittAssociates, Inc.

Description

DRAWINGS SCHEDULE

Foresite Group, Inc.5185 Peachtree PkwySuite 240Norcross, GA 30092

o | 770.368.1399f | 770.368.1944

w | www.fg-inc.net

NOT TO

SCALE

S0.1

GENERAL NOTES

GENERAL

1. NO PROVISION OF ANY REFERENCED STANDARD SPECIFICATION, MANUAL OR CODE (WHETHER OR

NOT SPECIFICALLY INCORPORATED BY REFERENCE IN THE CONTRACT DOCUMENTS) SHALL BE

EFFECTIVE TO CHANGE THE DUTIES AND RESPONSIBILITIES OF OWNER, CONTRACTOR, DESIGN

PROFESSIONAL, SUPPLIER, OR ANY OF THEIR CONSULTANTS, AGENTS, OR EMPLOYEES FROM THOSE

SET FORTH IN THE CONTRACT DOCUMENTS. NOR SHALL IT BE EFFECTIVE TO ASSIGN TO THE DESIGN

PROFESSIONAL OF RECORD OR ANY OF THE DESIGN PROFESSIONAL OF RECORD'S CONSULTANTS,

AGENTS, OR EMPLOYEES ANY DUTY OR AUTHORITY TO SUPERVISE OR DIRECT THE FURNISHING OR

PERFORMANCE OF THE WORK OR ANY DUTY OR AUTHORITY TO UNDERTAKE RESPONSIBILITIES

CONTRARY TO THE PROVISIONS OF THE CONTRACT DOCUMENTS.

2. CONTRACT DOCUMENTS INCLUDE, BUT ARE NOT LIMITED TO, THE STRUCTURAL DOCUMENTS

(DRAWINGS AND SPECIFICATIONS), BUT DO NOT INCLUDE SHOP DRAWINGS, VENDOR DRAWINGS, OR

MATERIAL PREPARED AND SUBMITTED BY THE CONTRACTOR.

3. REFERENCE TO STANDARD SPECIFICATIONS OF ANY TECHNICAL SOCIETY, ORGANIZATION, OR

ASSOCIATION OR TO CODES OF LOCAL OR STATE AUTHORITIES, SHALL MEAN THE LATEST STANDARD,

CODE, SPECIFICATION OR TENTATIVE SPECIFICATION ADOPTED AT THE DATE OF TAKING BIDS, UNLESS

SPECIFICALLY STATED OTHERWISE.

4. CONTRACT DOCUMENTS SHALL GOVERN IN THE EVENT OF A CONFLICT WITH THE CODE OF PRACTICE

OR SPECIFICATIONS OF ACI, PCI, AISC, SJI OR OTHER STANDARDS. WHERE A CONFLICT OCCURS

WITHIN THE CONTRACT DOCUMENTS, THE STRICTEST REQUIREMENT SHALL GOVERN.

5. MATERIAL, WORKMANSHIP, AND DESIGN SHALL CONFORM TO THE REFERENCED BUILDING CODE.

6. CONTRACTOR SHALL COORDINATE THE STRUCTURAL DOCUMENTS WITH THE ARCHITECTURAL,

MECHANICAL, ELECTRICAL, PLUMBING AND CIVIL DOCUMENTS. DESIGN PROFESSIONAL SHALL BE

NOTIFIED OF ANY DISCREPANCY OR OMISSION. FOR DIMENSIONS NOT SHOWN ON THE STRUCTURAL

DRAWINGS SEE THE ARCHITECTURAL DRAWINGS.

7. CONTRACTOR SHALL VERIFY EXISTING DIMENSIONS, ELEVATIONS, AND SITE CONDITIONS BEFORE

STARTING WORK. DESIGN PROFESSIONAL SHALL BE NOTIFIED OF ANY DISCREPANCY.

8. CONTRACTOR SHALL VERIFY THAT MISCELLANEOUS FRAMING SHOWN ON THE STRUCTURAL

DRAWINGS FOR MECHANICAL EQUIPMENT, OWNER-FURNISHED ITEMS, PARTITIONS, ETC. IS

CONSISTENT WITH THE REQUIREMENTS OF SUCH ITEMS.

9. CONTRACTOR HAS SOLE RESPONSIBILITY FOR MEANS, METHODS, TECHNIQUES, SEQUENCES, AND

PROCEDURES OF CONSTRUCTION.

10. THE STRUCTURE IS STABLE ONLY IN ITS COMPLETED FORM. TEMPORARY SUPPORTS REQUIRED FOR

STABILITY DURING ALL INTERMEDIATE STAGES OF CONSTRUCTION SHALL BE DESIGNED, FURNISHED,

AND INSTALLED BY THE CONTRACTOR.

11. CONTRACTOR HAS SOLE RESPONSIBILITY TO COMPLY WITH ALL OSHA REGULATIONS.

12. ELECTRONIC DRAWING FILES WILL NOT BE PROVIDED TO THE CONTRACTOR. REPRODUCTION OF

STRUCTURAL DRAWINGS FOR SHOP DRAWINGS IS NOT PERMITTED.

13. REVIEW OF SUBMITTALS OR SHOP DRAWINGS BY THE DESIGN PROFESSIONAL DOES NOT RELIEVE THE

CONTRACTOR OF THE SOLE RESPONSIBILITY TO REVIEW AND CHECK ALL SUBMITTALS AND SHOP

DRAWINGS BEFORE SUBMITTING TO THE DESIGN PROFESSIONAL. CONTRACTOR REMAINS SOLELY

RESPONSIBLE FOR ERRORS AND OMISSIONS ASSOCIATED WITH THE PREPARATION OF SHOP

DRAWINGS AS THEY PERTAIN TO MEMBER SIZES, DETAILS, AND DIMENSIONS SPECIFIED IN THE

CONTRACT DOCUMENTS.

14. DETAILS LABELED "TYPICAL" ON THE STRUCTURAL DRAWINGS APPLY TO ALL SITUATIONS OCCURRING

ON THE PROJECT THAT ARE THE SAME OR SIMILAR TO THE TYPICAL DETAILS UNLESS THOSE

LOCATIONS ARE SPECIFICALLY DETAILED OTHERWISE.

15. STRUCTURAL DESIGN PROFESSIONAL IS NOT RESPONSIBLE FOR THE DESIGN OF STEEL STAIRS,

HANDRAILS, CURTAIN WALL/WINDOW WALL SYSTEMS, COLD-FORMED METAL FRAMING, OR OTHER

SYSTEMS NOT SHOWN IN THE STRUCTURAL DOCUMENTS. SUCH SYSTEMS SHALL BE DESIGNED,

FURNISHED, AND INSTALLED AS REQUIRED BY OTHER PORTIONS OF THE CONTRACT DOCUMENTS.

CODE/DESIGN CRITERIA

1. STRUCTURE IS DESIGNED IN ACCORDANCE WITH THE FOLLOWING:

IBC BUILDING CODE, 2012 EDITION WITH GEORGIA AMENDMENTS.

2. GRAVITY LOADS

2.1 UNIFORM FLOOR LIVE LOADS (REDUCED AS ALLOWED BY THE BUILDING CODE):

FRAMED FLOOR 50 PSF

PARTITIONS 15 PSF

STAIRS 100 PSF

2.2 UNIFORM ROOF LIVE LOADS (REDUCED AS ALLOWED BY THE BUILDING CODE):

ROOF 20 PSF

PONDING AND DRIFT EFFECTS HAVE BEEN INCLUDED IN THE DESIGN.

2.3 CONCENTRATED FLOOR LOADS: DISTRIBUTED OVER AN AREA OF 2-1/2 SQUARE FEET, UNLESS

NOTED OTHERWISE:

OFFICE 2000 LB

2.4 DEAD LOADS (IN ADDITION TO STRUCTURE SELF-WEIGHT):

FLOOR:

MISCELLANEOUS 3.0 PSF

CEILING/MEP 2.0 PSF

ROOF:

ROOFING 4.5 PSF

INSULATION 1.5 PSF

MISCELLANEOUS 3.0 PSF

CEILING/MEP 2.0 PSF

3. WIND LOADS:

115 MPH BASIC WIND SPEED

IMPORTANCE FACTOR = 1.00

EXPOSURE B

INTERNAL PRESSURE COEFFICIENT = ±0.18

RISK CATEGORY II

SEE COMPONENT AND CLADDING DESIGN WIND PRESSURE DIAGRAM

4. EARTHQUAKE LOADS:

RISK CATEGORY: II

SEISMIC IMPORTANCE FACTOR: I = 1.00

SHORT PERIOD MAPPED SPECTRAL RESPONSE COEFFICIENT, SS = 0.160

1 SECOND PERIOD MAPPED SPECTRAL RESPONSE COEFFICIENT, S1 = 0.081

SITE CLASS D

SHORT PERIOD DESIGN SPECTRAL RESPONSE COEFFICIENT, SDS = 0.171

1 SECOND PERIOD DESIGN SPECTRAL RESPONSE COEFFICIENT, SD1 = 0.130

SEISMIC DESIGN CATEGORY: B

BASIC SEISMIC-FORCE RESISTING SYSTEM: ORDINARY REINFORCED MASONRY SHEAR WALLS

AND LIGHT-FRAMED WALLS SHEATHED WITH WOOD STRUCTURAL PANELS RATED FOR SHEAR

RESISTANCE OR STEEL SHEETS

DESIGN BASE SHEAR: 26.0 KIPS

SEISMIC RESPONSE COEFFICIENT

CS = 0.086, FOR MASONRY SHEAR WALLS

CS = 0.026, FOR LIGHT-FRAMED SHEAR WALLS

RESPONSE MODIFICATION FACTOR

R = 2, FOR MASONRY SHEAR WALLS

R = 6.5, FOR LIGHT-FRAMED SHEAR WALLS

ANALYSIS PROCEDURE: EQUIVALENT LATERAL FORCE PROCEDURE

5. UNLESS NOTED OTHERWISE CALCULATED INDIVIDUAL MEMBER DEFLECTIONS (IN INCHES) DO NOT

EXCEED THE FOLLOWING:

DEAD LOAD LIVE LOAD DEAD + LIVE LOAD

ROOF MEMBERS: L/360 L/360 L/240

FLOOR MEMBERS: L/360 L/360 L/240

WHERE, L = SPAN LENGTH (IN INCHES) BETWEEN SUPPORTS. (FOR CANTILEVERS, L IS TWICE

THE LENGTH OF THE CANTILEVER.) NOTE THAT THE TOTAL MAXIMUM CALCULATED FLOOR

SYSTEM DEFECTION WILL BE THE SUM OF THE DEFLECTIONS OF THE SUPPORTED ELEMENTS IN

A BAY.

THE CALCULATED DEFLECTION FOR INDIVIDUAL MEMBERS SUPPORTING MASONRY DO NOT

EXCEED L/600 FOR DESIGN LOADS APPLIED AFTER THE INSTALLATION OF THE MASONRY.

6. SPECIAL INSPECTIONS:

6.1 THE STRUCTURAL TESTING/INSPECTION AGENCY, SEE SPECIFICATION SECTION 014525, WILL

PERFORM SPECIAL INSPECTIONS AS REQUIRED BY CHAPTER 17 OF THE BUILDING CODE.

MATERIALS AND WORK TO BE INSPECTED INCLUDE SOILS, CONCRETE, MASONRY, AND STEEL

CONSTRUCTION. SEE SPECIFICATION SECTION 014525 FOR A COMPLETE LIST OF WORK

REQUIRING SPECIAL INSPECTIONS.

6.2 SPECIAL INSPECTION AS REQUIRED BY CHAPTER 17 OF THE BUILDING CODE ARE REQUIRED FOR

STRUCTURAL COMPONENTS AND ASSEMBLIES WHICH ARE NOT FABRICATED AT THE

CONSTRUCTION JOB SITE INCLUDING BUT NOT LIMITED TO FLOOR AND ROOF TRUSSES,

STRUCTURAL STEEL FRAMING, AND PRECAST CONCRETE, JOISTS, BEAMS, COLUMNS, SLABS,

WALLS AND CLADDING.

6.3 SPECIAL INSPECTION AS REQUIRED BY CHAPTER 17 OF THE BUILDING CODE MAY BE WAIVED FOR

ITEMS WHICH ARE PRODUCED ON THE PREMISES OF A FABRICATOR REGISTERED AND APPROVED

TO PERFORM SUCH WORK WITHOUT SPECIAL INSPECTION. APPROVAL SHALL BE BASED UPON

REVIEW OF THE FABRICATOR'S WRITTEN PROCEDURAL AND QUALITY CONTROL MANUALS AND BY

PERIODIC AUDITING OF FABRICATION PRACTICES BY AN APPROVED SPECIAL INSPECTION AGENCY.

THE APPROVED FABRICATOR SHALL SUBMIT A CERTIFICATE OF COMPLIANCE TO THE CHIEF

COMMERCIAL BUILDING INSPECTOR OR HIS DESIGNEE WHICH STATES THAT THE FABRICATION

WORK WAS PERFORMED IN ACCORDANCE WITH THE APPROVED CONSTRUCTION DOCUMENTS.

6.4 THE PROJECT OWNER WILL EMPLOY ONE OR MORE SPECIAL INSPECTORS TO PERFORM

INSPECTIONS AS REQUIRED BY CHAPTER 17 OF THE BUILDING CODE DURING CONSTRUCTION OF

THE PROJECT. DOCUMENTATION THAT SUMMARIZES THE QUALIFICATION AND CREDENTIALS OF

EACH SPECIAL INSPECTOR AND DEMONSTRATES COMPETENCE FOR INSPECTION OF EACH

PARTICULAR TYPE OF CONSTRUCTION REQUIRING SPECIAL INSPECTION SHALL BE SUBMITTED TO

THE CHIEF COMMERCIAL BUILDING INSPECTOR OR HIS DESIGNEE FOR REVIEW AND APPROVAL

PRIOR TO CONSTRUCTION.

6.5 APPROVED SPECIAL INSPECTORS SHALL FURNISH INSPECTION REPORTS TO THE CHIEF

COMMERCIAL BUILDING INSPECTOR OR HIS DESIGNEE AND TO THE DESIGN PROFESSIONAL WHICH

INDICATE THAT THE WORK INSPECTED WAS DONE IN CONFORMANCE WITH THE APPROVED

CONSTRUCTION DOCUMENTS. A FINAL REPORT WHICH DOCUMENTS THE RESULTS OF THE

SPECIAL INSPECTIONS PERFORMED INCLUDING CORRECTION OF ANY DISCREPANCIES IDENTIFIED

DURING INSPECTION SHALL BE SUBMITTED PERIODICALLY AT A FREQUENCY APPROVED BY CHIEF

COMMERCIAL BUILDING INSPECTOR PRIOR TO CONSTRUCTION.

7. NO PROVISIONS HAVE BEEN MADE FOR FUTURE HORIZONTAL OR VERTICAL EXPANSION.

FOUNDATION

1. FOUNDATION DESIGN IS BASED ON THE RECOMMENDATIONS IN THE GEOTECHNICAL REPORT

PREPARED BY GEOTECHNICAL & ENVIRONMENTAL CONSULTANTS, INC., REPORT NUMBER 160471.210

DATED JULY 11, 2016. DESIGN PROFESSIONAL IS NOT RESPONSIBLE FOR SUBSURFACE CONDITIONS

ENCOUNTERED IN THE FIELD DIFFERENT TO THOSE ASSUMED FOR DESIGN.

2. STRUCTURAL TESTING/INSPECTION AGENCY SHALL CERTIFY THE BEARING MEDIUM.

3. INDIVIDUAL SPREAD FOOTINGS AND CONTINUOUS FOOTINGS SHALL BEAR ON SOIL CAPABLE OF

SUPPORTING 2,500 PSF.

3.1 NO FOOTINGS SHALL BEAR ON ROCK. UNDERCUT ROCK A MINIMUM OF 2 FEET BELOW BOTTOM OF

FOOTING AND REPLACE WITH STRUCTURAL FILL.

4. PROOF ROLL BUILDING AREAS WITH TWO COMPLETE COVERAGES OF A LOADED DUMP-TRUCK OR

SCRAPER. REPLACE SOFT AREAS WITH COMPACTED STRUCTURAL FILL AS REQUIRED BY THE

SPECIFICATIONS.

5. STRUCTURAL FILL SHALL CONTAIN NO ORGANIC MATERIAL AND BE APPROVED BY A GEOTECHNICAL

ENGINEER PRIOR TO PLACEMENT. STRUCTURAL FILL UNDER SLABS AND WITHIN 10'-0" OF THE

BUILDING FOOTPRINT SHALL BE PLACED IN LIFTS OF THICKNESS DETERMINED BY THE INDEPENDENT

TESTING AGENCY AND COMPACTED TO AT LEAST 95% OF ITS STANDARD PROCTOR MAXIMUM DRY

DENSITY IN ACCORDANCE WITH ASTM D698. THE TOP 12" SUB-BASE UNDER SLABS ON GRADE SHALL

BE COMPACTED TO AT LEAST 98% OF ITS STANDARD PROCTOR MAXIMUM DRY DENSITY. ALL BACKFILL,

COMPACTION AND PROOF ROLLING OPERATIONS SHALL BE OBSERVED BY AN INDEPENDENT TESTING

LABORATORY.

6. SLABS-ON-GRADE SHALL BE PLACED ON A 4" GRANULAR BASE, COMPACTED TO 98% OF ITS STANDARD

PROCTOR MAXIMUM DRY DENSITY IN ACCORDANCE WITH ASTM D698, AND COVERED WITH A 10 MIL

CONTINUOUSLY SEALED VAPOR BARRIER. THE BASE FOR SLABS-ON-GRADE SHALL BE INSPECTED BY

A GEOTECHNICAL ENGINEER PRIOR TO EACH PLACEMENT OF CONCRETE.

7. FOOTINGS SHALL BE CENTERED ABOUT COLUMN LINES UNLESS NOTED OTHERWISE.

8. ALL FOOTINGS AND TURN DOWN SLAB EDGES SHALL PENETRATE TO A MINIMUM DEPTH OF 12" BELOW

FINISHED GRADE.

REINFORCEMENT

1. REINFORCING STEEL SHALL CONFORM TO ASTM A615, GRADE 60, UNLESS NOTED OTHERWISE.

2. WELDED WIRE FABRIC SHALL CONFORM TO ASTM A185 AND HAVE MINIMUM SIDE AND END LAPS OF 8".

3. SUBMIT SHOP DRAWINGS WHICH ADEQUATELY DEPICT THE REINFORCING BAR SIZES AND PLACEMENT.

WRITTEN DESCRIPTION OF REINFORCEMENT WITHOUT ADEQUATE SECTIONS, ELEVATIONS, AND

DETAILS IS NOT ACCEPTABLE.

4. SPLICES SHALL BE CLASS B IN ACCORDANCE WITH ACI 318, UNLESS NOTED OTHERWISE.

REINFORCEMENT SHALL BE SPLICED ONLY AT LOCATIONS SHOWN OR NOTED IN THE STRUCTURAL

DOCUMENTS, EXCEPT REINFORCEMENT MARKED "CONTINUOUS" CAN BE SPLICED AT LOCATIONS

DETERMINED BY CONTRACTOR. SPLICES AT OTHER LOCATIONS SHALL BE APPROVED IN WRITING BY

THE DESIGN PROFESSIONAL.

5. PROVIDE DOWELS FROM FOUNDATIONS THE SAME SIZE AND NUMBER AS THE VERTICAL WALL OR

COLUMN REINFORCING, UNLESS NOTED OTHERWISE.

6. PLACE REINFORCEMENT AS FOLLOWS, UNLESS NOTED OTHERWISE:

6.1 CONCRETE REINFORCEMENT COVER

EXPOSED TO EARTH OR WEATHER:

UNFORMED CAST AGAINST EARTH 3” CLEAR

FORMED #6 AND LARGER 2” CLEAR

FORMED #5 AND SMALLER 1-1/2” CLEAR

NOT EXPOSED TO EARTH OR WEATHER:

SLABS 3/4" CLEAR

6.2 MASONRY REINFORCING STEEL SHALL BE PLACED IN THE CENTER OF THE WALL UNLESS NOTED

OTHERWISE.

7. REINFORCING STEEL DESIGNATED CONTINUOUS SHALL BE LAPPED AS FOLLOWS:

CONCRETE REINFORCEMENT: CLASS B TENSION LAP

MASONRY REINFORCEMENT: 48 BAR DIAMETERS

8. ADHESIVE FOR REINFORCING DOWELS IN EXISTING CONCRETE SHALL CONFORM TO ASTM C881-02,

TYPE IV, GRADE 3, CLASS A, B, & C EXCEPT GEL TIMES AND EPOXY CONTENT. ADHESIVE SHALL

CONSIST OF A TWO COMPONENT ADHESIVE SYSTEM CONTAINED IN SIDE BY SIDE PACKAGING

CONNECTEED TO A MIXING NOZZLE WHICH THOROUGHLY MIXES THE COMPONENTS AS IT IS INJECTED

INTO THE HOLE. ADHESIVE SHALL HAVE PASSED ICC EVALUATION SERVICES, INC (ICC-ES)

ACCEPTANCE CRITERIA 308 FOR LONG TERM CREEP. REINFORCING INSTALLED IN CONCRETE THAT

MAY BECOME CRACKED UNDER SERVICE LOADS SHALL BE EVALUATED BY ICC-ES ACCEPTANCE

CRITERIA 308 AND BE SPECIFICALLY APPROVED FOR USE IN CRACKED CONCRETE. CONTACT DESIGN

PROFESSIONAL FOR DETERMINATION OF CRACKED OR UNCRACKED CONCRETE CONDITION UNLESS

CONDITION IS NOTED ON THE DRAWINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER'S

RECOMMENDATIONS. MINIMUM EMBEDMENT LENGTH SHALL BE 12 BAR DIAMETERS, UNLESS NOTED

OTHERWISE.

9. ALL DOWELS AND TERMINATING BARS SHALL HAVE A STANDARD 90 DEGREE HOOK.

10. ALL HORIZONTAL REINFORCING SHALL BE CONTINUOUS THROUGH CONTROL AND/OR CONSTRUCTION

JOINTS AND AROUND CORNERS.

CAST-IN-PLACE CONCRETE

1. CONCRETE WORK SHALL CONFORM TO ACI 318 AND CRSI STANDARDS.

2. CONCRETE SHALL HAVE THE FOLLOWING MINIMUM SPECIFIED 28-DAY COMPRESSIVE STRENGTH:

2.1 NORMAL WEIGHT STRUCTURAL CONCRETE:

FOOTINGS 3000 PSI

SLABS-ON-GRADE 4000 PSI

HOLLOW CORE SLABS 5000 PSI

3. PIPES OR DUCTS SHALL NOT EXCEED ONE-THIRD THE SLAB OR WALL THICKNESS INCLUDING

CROSSING UNLESS SPECIFICALLY DETAILED IN THE STRUCTURAL DOCUMENTS. ALL PIPES AND DUCTS

SHALL BE PLACED IN THE MIDDLE THIRD OF THE SLAB OR WALL THICKNESS UNLESS SPECIFICALLY

DETAILED OTHERWISE IN THE STRUCTURAL DOCUMENTS. SEE MECHANICAL AND ELECTRICAL

DRAWINGS FOR LOCATION OF SLEEVES, ACCESSORIES, ETC.

4. REFER TO ARCHITECTURAL DRAWINGS FOR MOLDS, GROOVES, ORNAMENTS, CLIPS OR GROUNDS

REQUIRED TO BE ENCASED IN CONCRETE AND FOR LOCATION OF FLOOR FINISHES AND SLAB

DEPRESSIONS.

5. CONSTRUCTION JOINT LOCATIONS SHALL BE APPROVED BY THE DESIGN PROFESSIONAL. NO

HORIZONTAL CONSTRUCTION JOINTS ARE PERMITTED EXCEPT THOSE SHOWN ON THE STRUCTURAL

DRAWINGS.

6. DEFECTIVE AREAS IN CONCRETE INCLUDING, BUT NOT LIMITED TO, HONEY-COMBING, SPALLS, AND

CRACKS WITH WIDTHS EXCEEDING 0.016 INCH SHALL BE REPAIRED. EXTENT OF DEFECTIVE AREA TO BE

DETERMINED BY THE DESIGN PROFESSIONAL.

STRUCTURAL PRECAST CONCRETE

1. PRECAST CONCRETE DESIGN, MANUFACTURE AND ERECTION SHALL CONFORM TO ACI 318 AND PCI

MANUAL 116.

2. PRECAST DESIGN LOADS:

2.1 PRECAST MEMBERS SHALL BE CAPABLE OF SUPPORTING THE SUPERIMPOSED LOADS AS GIVEN IN

THE CONTRACT DOCUMENTS, IN ADDITION TO THE SELF-WEIGHT OF THE PRECAST MEMBER,

TOPPINGS, ETC.

2.2 EFFECTS TO BE CONSIDERED BY THE PRECAST DESIGN ENGINEER IN THE DESIGN OF THE

PRECAST ELEMENTS AND CONNECTIONS INCLUDE, BUT ARE NOT LIMITED TO, THE FOLLOWING:

GRAVITY

WIND

SEISMIC

DIFFERENTIAL TEMPERATURE BETWEEN PANEL FACES

ECCENTRICITY OF APPLIED LOADS

LOADS FROM MATERIALS SUPPORTED BY PANELS

VOLUMETRIC CHANGES DUE TO TEMPERATURE, CREEP, & SHRINKAGE

ERECTION LOADS

LOAD COMBINATIONS SHALL BE IN ACCORDANCE WITH THE BUILDING CODE.

3. DESIGN OF STRUCTURAL PRECAST ELEMENTS AND THEIR CONNECTIONS SHALL BE THE SOLE

RESPONSIBILITY OF THE CONTRACTOR. SUBMIT SHOP DRAWINGS, DESIGN LOAD DATA, AND SUPPORT

REACTIONS OF PRECAST ELEMENTS AND THEIR CONNECTIONS SEALED BY AN ENGINEER LICENSED IN

THE PROJECT STATE. REVIEW SHALL BE FOR CONFORMANCE WITH THE CONTRACT DOCUMENTS

REGARDING ARRANGEMENT AND SIZES OF MEMBERS AND THE CONTRACTOR'S INTERPRETATION OF

THE DESIGN LOADS AND CONTRACT DOCUMENT DETAILS. SUCH REVIEW SHALL NOT RELIEVE THE

CONTRACTOR OF THE FULL RESPONSIBILITY FOR THE DESIGN OF THE PRECAST AND PRECAST

CONNECTIONS NOT SPECIFIED IN THE CONTRACT DOCUMENTS.

4. SUBMIT REACTIONS OF ALL PRECAST ELEMENTS SUPPORTED BY STRUCTURAL ELEMENTS SHOWN ON

THE DRAWINGS.

5. CONCRETE FOR PRECAST MEMBERS SHALL HAVE A MINIMUM 28-DAY COMPRESSIVE STRENGTH OF

5000 PSI.

6. FOR OPENINGS AND EMBEDDED ITEMS, CONTRACTOR SHALL COORDINATE WITH ARCHITECTURAL,

MECHANICAL, ELECTRICAL AND PLUMBING CONTRACT DOCUMENTS.

CONCRETE MASONRY

1. MINIMUM 28-DAY COMPRESSIVE STRENGTH OF CONCRETE MASONRY SHALL BE F'M = 1500 PSI.

2. MORTAR SHALL COMPLY WITH THE BUILDING CODE REQUIREMENTS FOR CONCRETE MASONRY AND

SHALL BE OF THE FOLLOWING TYPE:

WALLS BELOW GRADE TYPE M

BEARING WALLS TYPE M OR S

3. CONCRETE MASONRY UNITS SHALL BE GROUTED WITH 2500 PSI COARSE GROUT AS SHOWN IN THE

STRUCTURAL DOCUMENTS. GROUT FOR REINFORCED AND NONREINFORCED MASONRY SHALL

CONFORM TO ASTM C476.

4. PROVIDE HORIZONTAL JOINT REINFORCEMENT WITH NO. 9 GAGE LONGITUDINAL WIRES AT 16" C/C

VERTICALLY, UNLESS NOTED OTHERWISE. PROVIDE SPECIAL ACCESSORIES FOR CORNERS,

INTERSECTIONS, ETC.

5. PROVIDE OPEN BOTTOM BEAM BLOCK UNITS WITH 3" DEEP MINIMUM WEB OPENINGS AT HORIZONTAL

REINFORCEMENT LOCATIONS. A MINIMUM CLEAR SPACE OF ONE BAR DIAMETER SHALL BE PROVIDED

BETWEEN THE REINFORCING BARS AND THE FACE OF MASONRY UNITS.

6. PROVIDE CONTROL JOINTS IN ALL CONCRETE MASONRY WALLS AT LOCATIONS APPROVED BY THE

DESIGN PROFESSIONAL AT A MAXIMUM SPACING OF 3 TIMES THE WALL HEIGHT OR 40'-0", WHICHEVER

IS LESS.

7. PROVIDE DOVETAIL ANCHORS AT 16" C/C, UNLESS NOTED OTHERWISE, WHERE MASONRY WALLS ABUT

CONCRETE SURFACES.

8. SUBMIT WRITTEN CONSTRUCTION PROCEDURES PRIOR TO THE START OF MASONRY CONSTRUCTION.

9. MINIMUM VERTICAL WALL REINFORCEMENT SHALL BE #5@32" C/C, UNLESS NOTED OTHERWISE.

STRUCTURAL STEEL

1. STRUCTURAL STEEL SHALL CONFORM TO ASTM A992, UNLESS NOTED OTHERWISE.

STRUCTURAL STEEL TUBING SHALL CONFORM TO ASTM A500, GRADE B.

STRUCTURAL STEEL PIPE SHALL CONFORM TO ASTM A53, GRADE B.

STRUCTURAL CHANNELS, MISCELLANEOUS PLATES AND CONNECTION MATERIAL SHALL

CONFORM TO ASTM A36, UNLESS NOTED OTHERWISE.

2. BOLTS AND ANCHORS:

2.1 BOLTED CONNECTIONS SHALL BE TYPE N (BEARING TYPE WITH THREADS INCLUDED IN SHEAR

PLANE) WITH MINIMUM 3/4" DIAMETER A325 BOLTS. SUBMIT PROPOSED BOLT TIGHTENING

PROCEDURE FOR REVIEW.

2.2 ANCHOR BOLTS SHALL BE HEADED BOLTS CONFORMING TO ASTM F1554 AND SHALL BE HEADED

RODS OR THREADED RODS WITH HEAVY HEXAGONAL NUT WELDED TO THE BOTTOM OF THE

THREADED ROD, GRADE A36, UNLESS NOTED OTHERWISE.

2.3 EXPANSION ANCHORS SHALL HAVE BEEN EVALUATED BY THE ICC EVALUATION SERVICES, INC

(ICC-ES) WITH A PUBLISHED EVALUATION REPORT. ANCHORS INSTALLED IN CONCRETE THAT MAY

BECOME CRACKED UNDER SERVICE LOADS SHALL BE EVALUATED BY ICC-ES ACCEPTANCE

CRITERIA 193 AND BE SPECIFICALLY APPROVED FOR USE IN CRACKED CONCRETE. CONTACT

DESIGN PROFESSIONAL FOR DETERMINATION OF CRACKED OR UNCRACKED CONCRETE

CONDITION UNLESS CONDITION IS NOTED ON THE DRAWINGS. ALL ANCHORS SHALL BE APPROVED

FOR RESISTING WIND AND SEISMIC LOADS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER'S

RECOMMENDATIONS. MINIMUM EMBEDMENT SHALL BE EQUAL TO 4.5 TIMES THE ANCHOR

DIAMETER, UNLESS NOTED OTHERWISE.

2.4 ADHESIVE ANCHORS SHALL CONSIST OF AN ALL-THREAD STEEL ANCHOR WITH ADHESIVE

CONFORMING TO ASTM C881-02, TYPE IV, GRADE 3, CLASS A, B, & C EXCEPT GEL TIMES AND EPOXY

CONTENT. ADHESIVE SHALL CONSIST OF A TWO COMPONENT ADHESIVE SYSTEM CONTAINED IN

SIDE BY SIDE PACKAGING CONNECTEED TO A MIXING NOZZLE WHICH THOROUGHLY MIXES THE

COMPONENTS AS IT IS INJECTED INTO THE HOLE. ADHESIVE SHALL HAVE PASSED ICC EVALUATION

SERVICES, INC (ICC-ES) ACCEPTANCE CRITERIA 308 FOR LONG TERM CREEP. ANCHORS INSTALLED

IN CONCRETE THAT MAY BECOME CRACKED UNDER SERVICE LOADS SHALL BE EVALUATED BY

ICC-ES ACCEPTANCE CRITERIA 308 AND BE SPECIFICALLY APPROVED FOR USE IN CRACKED

CONCRETE. CONTACT DESIGN PROFESSIONAL FOR DETERMINATION OF CRACKED OR UNCRACKED

CONCRETE CONDITION UNLESS CONDITION IS NOTED ON THE DRAWINGS. INSTALL IN

ACCORDANCE WITH THE MANUFACTURER'S RECOMMENDATIONS. MINIMUM EMBEDMENT SHALL BE

EQUAL TO 4.5 TIMES THE ANCHOR DIAMETER, UNLESS NOTED OTHERWISE.

3. STRUCTURAL STEEL SHALL BE FABRICATED AND ERECTED ACCORDING TO BOTH THE AISC

“SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS” AND THE AISC "CODE OF STANDARD PRACTICE

FOR STEEL BUILDINGS AND BRIDGES".

4. SUBMIT SHOP DRAWINGS WHICH ADEQUATELY DEPICT THE STRUCTURAL ELEMENTS AND

CONNECTIONS SHOWN IN THE CONTRACT DOCUMENTS. CONNECTIONS SHALL BE DETAILED BASED ON

THE DESIGN INFORMATION PROVIDED IN THE CONTRACT DOCUMENTS. CONNECTIONS SHALL BE

DESIGNED FOR THE SERVICE LOAD REACTION VALUES SHOWN ON THE STRUCTURAL DRAWINGS. FOR

STEEL MEMBERS WHOSE REACTIONS ARE NOT SHOWN, THE DESIGN REACTION SHALL BE OBTAINED

FROM THE TABLES ENTITLED "MAXIMUM TOTAL UNIFORM LOAD" IN PART 3 OF THE AISC "MANUAL OF

STEEL CONSTRUCTION", THIRTEENTH (13TH) EDITION. THE DESIGN REACTION IS EQUAL TO HALF THE

TABULATED VALUE FOR NONCOMPOSITE BEAMS AND EQUAL TO THE TABULATED VALUE FOR

COMPOSITE BEAMS. DEVIATION FROM THE CONNECTION DETAILS DEPICTED IN THE CONTRACT

DOCUMENTS SHALL NOT BE PERMITTED WITHOUT WRITTEN PERMISSION FROM THE DESIGN

PROFESSIONAL. REVIEW DOES NOT RELIEVE THE CONTRACTOR OF THE FULL RESPONSIBILITY FOR

THE DESIGN AND ADEQUACY OF SUCH CONNECTIONS. DESIGN PROFESSIONAL SHALL BE

COMPENSATED BY THE CONTRACTOR FOR THE COST INVOLVED IN THE REDESIGN OF CONNECTIONS

FOR THE CONVENIENCE OF THE CONTRACTOR. SINGLE ANGLE CONNECTIONS ARE NOT ACCEPTABLE.

5. USE PRE-QUALIFIED WELDED JOINTS IN ACCORDANCE WITH AISC AND THE STRUCTURAL WELDING

CODE OF THE AMERICAN WELDING SOCIETY. "NON-PRE-QUALIFIED JOINTS" SHALL BE QUALIFIED PRIOR

TO FABRICATION.

6. STRUCTURAL STEEL EXPOSED TO WEATHER SHALL BE GALVANIZED.

METAL DECK

1. DECK DESIGN IS BASED ON THE STEEL DECK INSTITUTE DESIGN MANUAL FOR COMPOSITE DECKS,

FORM DECKS AND ROOF DECKS.

2. PROVIDE GLAVANIZED ROOF DECK WITH THE FOLLOWING MINIMUM PROPERTIES:

1.5 INCH DEPTH

22 GAGE THICKNESS

0.192 IN3/FT SECTION MODULUS

0.169 IN4/FT MOMENT OF INERTIA

33,000 PSI YIELD STRESS

3. DECK IS SPECIFIED BASED ON A THREE SPAN CONDITION. FURNISH HEAVIER GAGE DECK IF REQUIRED

FOR ONE OR TWO SPAN CONDITIONS.

4. FASTEN ROOF DECK TO RESIST A NET UPLIFT AS INDICATED ON THE DRAWINGS.

5. FASTEN DECK TO RESIST AN ULTIMATE DIAPHRAGM SHEAR FORCE OF 500 POUNDS PER LINEAR FOOT.

COLD-FORMED STEEL

1. DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS AND THEIR CONNECTIONS SHALL BE THE

SOLE RESPONSIBILITY OF THE CONTRACTOR. SUBMIT SHOP DRAWINGS SEALED BY AN ENGINEER

LICENSED IN THE PROJECT STATE. REVIEW OF SHOP DRAWINGS SHALL BE FOR CONFORMANCE WITH

THE CONTRACT DOCUMENTS REGARDING ARRANGEMENT AND SIZES OF MEMBERS AND THE

CONTRACTOR'S INTERPRETATION OF THE DESIGN LOADS AND CONTRACT DOCUMENT DETAILS. SUCH

REVIEW SHALL NOT RELIEVE THE CONTRACTOR OF FULL RESPONSIBILITY FOR THE DESIGN OF THE

COLD-FORMED STEEL STRUCTURAL MEMBERS AND THEIR CONNECTIONS.

2. COLD-FORMED STEEL DESIGN, FABRICATION AND ERECTION SHALL BE IN ACCORDANCE WITH AISI

"SPECIFICATION FOR DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS" OR "LOAD AND

RESISTANCE FACTOR DESIGN SPECIFICATION FOR COLD-FORMED STEEL STRUCTURAL MEMBERS".

3. COLD-FORMED STEEL STUDS, JOISTS AND ACCESSORIES SHALL BE AS SHOWN IN THE STRUCTURAL

DOCUMENTS.

4. COLD-FORMED STEEL TRUSSES SHALL BE DESIGNED FOR THE DESIGN LOADS SHOWN IN THE

CONTRACT DOCUMENTS. REFER TO THE SPECIFICATIONS.

5. COLD-FORMED STEEL STRUCTURAL MEMBERS MAY BE ATTACHED BY EITHER WELDS OR SCREWS

SIZED BY THE MANUFACTURER FOR THE SPECIFIED DESIGN LOADS. SEE THE SPECIFICATIONS.

6. CONTRACTOR SHALL FURNISH COMPLETE FABRICATION AND ERECTION DRAWINGS FOR APPROVAL BY

THE STRUCTURAL ENGINEER PRIOR TO THE COMMENCEMENT OF FABRICATION. INCLUDE PLACING

DRAWINGS FOR FRAMING MEMBERS SHOWING SIZE AND GAGE DESIGNATIONS, NUMBER, TYPE,

LOCATION AND SPACING. INDICATE SUPPLEMENTAL STRAPPING, BRACING, SPLICES, BRIDGING,

ACCESSORIES AND DETAILS REQUIRED FOR PROPER INSTALLATION.

7. AXIALLY LOADED BEARING STUDS SHALL BE POSITIONED SUCH THAT STUD LOCATION IS DIRECTLY

UNDER JOIST BEARING POINT UNLESS NOTED OTHERWISE IN THE STRUCTURAL DOCUMENTS.

8. SPLICES IN AXIALLY LOADED STUDS AND FLOOR OR ROOF JOISTS SHALL NOT BE PERMITTED.

9. WELDING OF COLD-FORMED STEEL SHALL BE IN ACCORDANCE WITH THE STANDARD CODE OF ARC

AND GAS WELDING IN BUILDING CONSTRUCTION.

WOOD

1. PLYWOOD DIAPHRAGMS SHALL BE EITHER STRUCTURAL I OR II SOUTHERN PINE PLYWOOD WITH

THICKNESS AS NOTED IN THE STRUCTURAL DOCUMENTS. PLYWOOD SHALL CONFORM TO THE

REQUIREMENTS OF THE BUILDING CODE.

2. PLYWOOD SHALL BE ORIENTED AND NAILED TO SUPPORTING MEMBERS AS NOTED IN THE

STRUCTURAL DOCUMENTS.

3. PLYWOOD SHALL BE PROVIDED IN ACCORDANCE WITH THE RECOMMENDATIONS OF THE AMERICAN

PLYWOOD ASSOCIATION (APA). THE MINIMUM THICKNESSES WHICH FOLLOW SHALL BE INCREASED AS

REQUIRED TO SATISFY ARCHITECTURAL REQUIREMENTS.

3.1 ROOF SHEATHING SHALL BE APA RATED SHEATHING, EXPOSURE 1, 48"x96". FOR SUPPORTS 24" OC

USE 15/32" 32/16 PLYWOOD. FOR SUPPORTS 16" OC USE 7/16" 24/16 PLYWOOD. PLYWOOD SHALL

BE TONGUE AND GROOVE OR BE INSTALLED WITH PANEL CLIPS IN ACCORDANCE WITH APA

RECOMMENDATIONS. WHERE ALLOWABLE SPANS ARE EXCEEDED AT ROOF SLOPE TRANSITIONS,

PROVIDE SPECIALLY DESIGNED SUPPLEMENTAL MEMBERS AS REQUIRED. SHEATHING SHALL BE

INSTALLED WITH THE LONG EDGE ACROSS A MINIMUM OF THREE SUPPORTING MEMBERS.

SUPPORT AND STAGGER EDGES OF PLYWOOD PARALLEL TO SUPPORTING MEMBER. PROVIDE

CONTINUOUS BLOCKING AT PERIMETER OF EACH DIAPHRAGM PLANE (INCLUDING ROOF SLOPE

TRANSITIONS) AND AROUND OPENINGS. FASTEN SHEATHING WITH 8d NAILS AT 6" OC AT

SUPPORTED EDGES UNO AND AT 12" OC AT INTERMEDIATE SUPPORTS. (V=240 LBS/FT 8d NAILS,

V=255 LBS/FT 10d NAILS FOR LOAD PARALLEL TO SUPPORTS; V=180 LBS/FT 8d NAILS, V=190 LBS/FT

10d NAILS FOR LOAD PERPENDICULAR TO SUPPORTS) AN 1/8" GAP SHALL BE LEFT BETWEEN

ADJACENT PANELS. PROTECT EDGES AGAINST EXPOSURE TO WEATHER OR USE EXTERIOR GRADE

PLYWOOD. COVER SHEATHING AS SOON AS POSSIBLE WITH ROOFING FELT OR SHINGLE

UNDERLAYMENT FOR PROTECTION AGAINST EXCESSIVE MOISTURE PRIOR TO ROOFING

INSTALLATION.

3.2 WALL SHEATHING SHALL BE 15/32" APA RATED SHEATHING, 32/16, EXPOSURE I, 48"x96" WITH

CONTINUOUSLY SUPPORTED EDGES. AN 1/8" GAP SHALL BE LEFT BETWEEN ADJACENT PANELS.

PROVIDE ONE LAYER ON ONE SIDE OF WALL UNLESS INDICATED ON PLAN TO PROVIDE ONE LAYER

ON EACH SIDE OF WALL.

3.3 FASTEN SHEATHING WITH 8d NAILS @ 6" OC AT PANEL EDGES AND @ 12" OC AT INTERMEDIATE

SUPPORTS.

ROOF PLAN COMPONENTS AND CLADDING

ULTIMATE WIND PRESSURE DIAGRAM

CONCESSION STAND

= -27 PSF/+16 PSF

= -41 PSF/+16 PSF

= -59 PSF/+16 PSF

NOTE: WIND PRESSURE BASED ON 50 SQUARE

FOOT AREA. NEGATIVE INDICATES

PRESSURE AWAY FROM SURFACE

SPLASH PAD

= -25 PSF/+16 PSF

= -38 PSF/+16 PSF




WALL ELEVATION COMPONENTS AND CLADDING

ULTIMATE WIND PRESSURE DIAGRAM

CONCESSION STAND

= -31 PSF/+29 PSF

= -36 PSF/+29 PSF




SPLASH PAD

= -29 PSF/+26 PSF

= -33 PSF/+26 PSF




brucem

Text Box

71

brucem

Line

A

B

C

B.5

D

1 2 3 4

13

'-8

"6

'-4

"7

'-0

"1

3'-8

"

24'-8" 15'-0" 15'-0"

8" MASONRY SHEAR

WALLS, SEE NOTE 6

P

1

F

1

P

1

F

1

P

1

F

1

P

1

F

1

C.J.

C.J.

C.J.

C.J.

C.J.

C

SEE ARCH

SEE NOTE 3

A

A

A

A

A

A

A

A

A

A

AA

A

A

A

A

A

E

E

E

E

EE

E

EE

E

E

C

C

E

C

AAA

13

S3.1

10

S3.1

5

S3.1

9

S3.1

C.J.

C.J.

C.J.

C.J.

4'-8

"4

'-8

"

NOTE 9, TYP.

13

S3.1

SLOPE

SEE ARCH.

T/FTG = -(2'-0")

T/FTG = -(2'-0")

T/FTG = -(2'-0")

T/FTG = -(2'-0")

P

1

F

1

P

1

F

1

P

1

F

1

17

S3.1

17

S3.1



(770) 416-7511

www.mackcain.com









DESIGNED BY:

DRAWN BY:

CHECKED BY:

APPROVED BY:

PROJECT NO.

SHEET

SCALE:

DATE:

RE

LE

AS

ED

F

OR

C

ON

ST

RU

CT

IO

N

150536

No. Date



3301 R

OF

F A

VE

NU

E

MA

CO

N, G

A 31204

09/30/16

HJ

BCR

HJ

HJ



Phone: (770)416-7511Fax: (770)416-6759



Description

DRAWINGS SCHEDULE


o | 770.368.1399f | 770.368.1944

w | www.fg-inc.net

FOUNDATION PLAN - CONCESSION STAND

1/4" = 1'-0"

1

S1.1

NOTES:

1. SEE S0.1 FOR GENERAL STRUCTURAL NOTES.

2. SEE ARCH FOR ADDITIONAL INFORMATION AND DIMENSIONS.

3. PROVIDE 4" GRADE SUPPORTED SLAB REINFORCED WITH WWF 6x6 W1.4xW1.4 WELDED WIRE FABRIC ON 4" GRANULAR

SUBBASE AND VAPOR BARRIER. T/SLAB EL = 0'-0".

4. Fx INDICATES FOOTING SIZE, SEE 1/S3.1. T/FTG = -1'-4" UNO BASED ON T/SLAB REFERENCE ELEVATION = 0'-0".

5. Px INDICATES CMU PILASTER, SEE 9/S4.1.

6. INDICATES LOAD BEARING CMU WALL REINFORCED W/ #5@32" O.C., UNO. SEE 5, 6, &10/S4.1. T/FTG EL = -1'-4" UNO.

INDICATES NON LOAD-BEARING CMU PARTITION WALL REINFORCED W/ #4@48" O.C., UNO. SEE 18/S3.1.

7. INDICATES ADDITIONAL CMU WALL REINFORCEMENT, SEE 1/S4.1.

8. C.J. INDICATES SLAB CONTROL JOINT. SEE 2/S3.1 AND GENERAL NOTES FOR ADDITIONAL INFORMATION.

9. PROVIDE REINFORCEMENT AT RE-ENTRANT CORNERS, SEE 6/S3.1.

10. CONTRACTOR SHALL BE RESPONSIBLE FOR COORDINATION OF ALL UTILITY AND PLUMBING LINES. SEE 14/S3.1.

X

AS SHOWN

S1.1

FOUNDATION

PLAN -

CONCESSION

STAND

brucem

Line

brucem

Text Box

72

B

C

D

C.5

E

1 2 3 4

W12x16

W12x16

W12x16

W12x16

W12x16

W12x16

W12x16

W12x16

W12x16

W12x16

13

'-8

"6

'-4

"7

'-0

"1

3'-8

"

23'-2" 15'-0" 15'-0"

W1

2x1

6W

12

x1

6

W1

2x1

4W

12

x1

4W

12

x1

4

6" METAL STUD WALL,

SEE NOTE 5

8" MASONRY SHEAR

WALL BELOW

SEE NOTE 4

DE

CK

B

RG

EL

=

+

10

'-2

"

2

S4.1

2

S5.1

9'-8

"9

'-8

"

1'-0" 1'-0"

6"

15

S5.1

11

S5.1

18

S5.1

5

S5.1

10

S5.1

9

S5.1

6

S5.1

14

S5.1

DE

CK

B

RG

EL

=

+

10

'-4

"

W8

x1

0W

8x1

0W

8x1

0W

8x1

0W

8x1

0W

8x1

0W

8x1

0W

8x1

0W

8x1

0

W12x16

W8

x1

0

13

S5.1

A

F

1.8

1'-6"

PROVIDE DOUBLE METAL STUD PACK

AT LOCATION OF CONNECTION OF

PRE-ENGINEERED CANOPY, TYP.



(770) 416-7511

www.mackcain.com









DESIGNED BY:

DRAWN BY:

CHECKED BY:

APPROVED BY:

PROJECT NO.

SHEET

SCALE:

DATE:

RE

LE

AS

ED

F

OR

C

ON

ST

RU

CT

IO

N

150536

No. Date



3301 R

OF

F A

VE

NU

E

MA

CO

N, G

A 31204

09/30/16

HJ

BCR

HJ

HJ



Phone: (770)416-7511Fax: (770)416-6759



Description

DRAWINGS SCHEDULE


o | 770.368.1399f | 770.368.1944

w | www.fg-inc.net

SECOND FLOOR FRAMING PLAN - CONCESSION STAND

1/4" = 1'-0"

1

S1.2

NOTES:



3. INDICATES DIRECTIONAL SPAN OF 1-1/2" TYPE B WIDE RIB 22 GAUGE GALVANIZED METAL ROOF DECK, SEE 3/S5.1.

4. INDICATES DIRECTIONAL SPAN OF 6" HOLLOW CORE PRECAST CONCRETE SLAB W/ 2" TOPPING. DESIGN OF

HOLLOWCORE SHALL INCLUDE 800 PLF NOMINAL LINE LOAD FOR LOAD-BEARING METAL STUD WALL, SEE PLAN. T/SLAB EL =

+10'-8" ABOVE FINISHED FLOOR.

5. INDICATES 6" METAL SHEAR STUD WALL W/ 6" DEEP, 1 5/8" LEG 18 GAUGE STUDS MIN @ 16" O.C. PROVIDE 1/2"

PLYWOOD SHEATHING CONNECTED TO METAL STUDS.

AS SHOWN

S1.2

SECOND FLOOR

FRAMING PLAN -

CONCESSION

STAND

brucem

Line

brucem

Text Box

73

A

B

C

B.5

D

1 2 3 4

13

'-8

"6

'-4

"7

'-0

"1

3'-8

"

24'-8" 15'-0" 15'-0"

T3

T4

T

2

T

2

T

2

T

2

T1

T6

T1

T6

T1

T6

T1

T6

T4

T5

T5

OPENING FOR

CUPOLA, SEE ARCH

6" LOAD BEARING

LIGHT GAUGE METAL

STUD WALL BELOW

T3

T3

T3

T3

T3

T3

T3

T3

T3

T3

T3

T3

T3

T3

T3

T3

T3

T4

T4

T3

T3

T4

T4

T4

T4

T4

T4

T4

T3

T3

T4

T4

T4

T4

T3

T3

T4

T4

T4

T4

T3

T3

T4

T4

T4

T4

T4

T4

T4

T4

T4

WALL OPENING, PROVIDE (2)

10" DEEP AND (2) 6" DEEP, 1

5/8" LEG 18 GAUGE BOXED

BEAM AT LINTEL, TYP.

PROVIDE DOUBLE WALL STUDS

AT TRUSS BEARING, TYP. AT T1

& T2.

(4) 6" DEEP 18

GA BOXED BEAM

(4) 6" DEEP 18

GA BOXED BEAM

(4) 6" DEEP 18

GA BOXED BEAM

(4) 6" DEEP 18

GA BOXED BEAM

PROVIDE TWO FULL HEIGHT STUDS

AT EACH JAMB AND CORNER, TYP.

18

S5.1

TYP.



(770) 416-7511

www.mackcain.com









DESIGNED BY:

DRAWN BY:

CHECKED BY:

APPROVED BY:

PROJECT NO.

SHEET

SCALE:

DATE:

RE

LE

AS

ED

F

OR

C

ON

ST

RU

CT

IO

N

150536

No. Date



3301 R

OF

F A

VE

NU

E

MA

CO

N, G

A 31204

09/30/16

HJ

BCR

HJ

HJ



Phone: (770)416-7511Fax: (770)416-6759



Description

DRAWINGS SCHEDULE


o | 770.368.1399f | 770.368.1944

w | www.fg-inc.net

ROOF FRAMING PLAN - CONCESSION STAND

1/4" = 1'-0"

1

S1.3

NOTES:



3. INDICATES DIRECTIONAL SPAN OF 5/8" EXTERIOR GRADE PLYWOOD ROOF SHEATHING ON PRE-FABRICATED LIGHT

GAUGE METAL TRUSSES SPACED AT 2'-0" O.C. MAXIMUM. SEE 8/S5.1.

4. Tx INDICATES PRE-FABRICATED LIGHT GAUGE METAL TRUSS PROFILE, SEE 1/S5.2. TRUSS BEARING EL = 19'-8" ABOVE FIRST

FINISHED FLOOR.

AS SHOWN

S1.3

ROOF FRAMING

PLAN -

CONCESSION

STAND

brucem

Line

brucem

Text Box

74

1 2

A

B

C

D

24'-0"

16

'-0

"1

2'-0

"1

6'-0

"

SEE NOTE 4

SEE NOTE 4

SEE NOTE 4

WOOD TRELLIS POST,

SEE NOTE 7

C.J.

SE

E N

OT

E 3

5

S3.1

9

S3.1

13

S3.1

1 2

A

B

C

D

24'-0"

16

'-0

"1

2'-0

"1

6'-0

"

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T4

T6

T6

T3

T3

T1

T1

T2

T

5

T

5

T1

T1

T2

T

5

T

5

W8

x1

8

W8

x1

8

OPENING FOR CUPOLA,

SEE ARCH

20

S5.1

19

S5.1

C.J.

C.J.

C

A

A

C

C

C

C

A

A

C

C

C

AA

AA

A AE E A A

E

E

E

C C

2

S4.1

13

S3.1

C.J.

C.J.C.J.

F

2

F

2

F

2

F

2

SLOPE 1"

SEE ARCH.

SLOPE 1"

SEE ARCH.



(770) 416-7511

www.mackcain.com









DESIGNED BY:

DRAWN BY:

CHECKED BY:

APPROVED BY:

PROJECT NO.

SHEET

SCALE:

DATE:

RE

LE

AS

ED

F

OR

C

ON

ST

RU

CT

IO

N

150536

No. Date



3301 R

OF

F A

VE

NU

E

MA

CO

N, G

A 31204

09/30/16

HJ

BCR

HJ

HJ



Phone: (770)416-7511Fax: (770)416-6759



Description

DRAWINGS SCHEDULE


o | 770.368.1399f | 770.368.1944

w | www.fg-inc.net

SPLASH PAD FOUNDATION PLAN

1/4" = 1'-0"

1

S1.4

NOTES:



3. C.J. INDICATES SLAB CONTROL JOINT. SEE 2/S3.1 AND GENERAL NOTES FOR ADDITIONAL INFORMATION.

4. PROVIDE 4" GRADE SUPPORTED SLAB REINFORCED WITH WWF 6x6 W1.4xW1.4 WELDED WIRE FABRIC ON 4" GRANULAR

SUBBASE AND VAPOR BARRIER. T/SLAB EL = 0'-0".

5. INDICATES LOAD-BEARING CMU WALL REINFORCED W/ #5@32" O.C., UNO. SEE 5, 6, & 8/S4.1. T/FTG EL = -1'-4".

INDICATES NON LOAD-BEARING CMU PARTITION REINFORCED W/ #4@48" O.C., UNO. SEE 18/S3.1.

6. INDICATES ADDITIONAL CMU WALL REINFORCEMENT, SEE 1/S4.1.

7. WOOD TRELLIS BY LANDSCAPE ARCHITECT.

8. TOP OF FOOTING ELEVATION = -1'-4" BASED ON T/SLAB REFERENCE ELEVATION = 0'-0".

9. CONTRACTOR SHALL BE RESPONSIBLE FOR COORDINATION OF ALL UTILITY AND PLUMBING LINES. SEE 14/S3.1.

X

SPLASH PAD ROOF FRAMING PLAN

1/4" = 1'-0"

2

S1.4

NOTES:



3. INDICATES DIRECTIONAL SPAN OF 5/8" EXTERIOR GRADE PLYWOOD ROOF SHEATHING ON PRE-ENGINEERED LIGHT

GAUGE METAL TRUSSES SPACED AT 2'-0" O.C. MAXIMUM, SEE 8/S5.1.

4. Tx INDICATES PRE-FABRICATED LIGHT GAUGE METAL TRUSS PROFILE, SEE 2/S5.2. TRUSS BEARING ELEVATION = +9'-5 1/2"

ABOVE FIRST FINISHED FLOOR.

AS SHOWN

S1.4

SPLASH PAD

PLANS

brucem

Line

brucem

Text Box

75

FOOTING SCHEDULE

3/4" = 1'-0"

F1 2'-0"x3'-0"x12" 3#4 LONG, 4#4 SHORT BOTTOM

REMARKSREINF

SIZE (WxLxT)

MARK

FOOTING SCHEDULE

TYPICAL INTERIOR 8" CMU WALL FOOTING

3/4" = 1'-0"

1

5

8" 8" 8"

8"

MIN

1'-0

"

T/SLAB EL

T/FTG EL

1

5

CMU WALL

DOWEL TO MATCH

VERT WALL REINF

ALTERNATE HOOKS

3#5 CONT.

STANDARD WEIGHT HORIZ

JOINT REINF AT 8" BELOW

GRADE AND AT 16" ABOVE

GRADE

BOND BREAKER

#4 CONT.

WWF

TYPICAL GRADE SUPPORTED SLAB AT JOINTS

3/4" = 1'-0"

NOTE: SAW CUT OR DISCONTINUE REINF AT

CONTRACTION JT

CONSTRUCTION JOINT

CONTRACTION JOINT

SLAB REINF IN TOP 1/3 OF SLAB

1/8"x1/3 SLAB DEPTH SAW CUT JT

SLAB REINF IN TOP 1/3 OF SLAB

TOOLED JT

TYPICAL TYPICAL REINFORCEMENT AT SLAB

RE-ENTRANT CORNER

3/4" = 1'-0"

3

"

2

"

BLDG CORNER OR CONSTRUCTION JT

2#5 x 4'-0" TOP

TYPICAL TURN DOWN SLAB AT JOINT

3/4" = 1'-0"

8"

1'-4

"

MIN

1/2" EXP JT

SLAB ON GRADE,

SEE CIVIL

WWF

#4@12"

3'-0"

2#5 CONT

T/SLAB EL

2

1

TYPICAL THICKENED FOOTING AT UNDERGROUND

PIPING

3/4" = 1'-0"

WA

LL

F

TG

3"

MIN

2'-8"

1'-6"2'-0"

MIN

F

TG

T

HIC

KN

ES

S

2'-0" 1'-6"

2'-8"

PIPE NEAR TOP OF FOOTING

CL OF PIPE

T/FTG EL

3"

MIN

1'-6" 2'-0"

MIN

F

TG

T

HIC

KN

ES

S

2'-0" 1'-6"

PIPE AT BOTTOM OF FOOTING

2'-8"2'-8"

PIPE UNDER FOOTING

NOTE:

VERIFY PIPE PENETRATION

LOCATIONS W/ PLUMBING

CONTRACTOR

T/FTG EL

T/FTG EL

6"

MIN

WA

LL

F

TG

WA

LL

F

TG

ADDL REINF TO MATCH

FTG REINF

FTG REINF

ADDL REINF TO

MATCH FTG REINF

FTG REINF

FTG REINF

#6@12"

#6@12"

TYPICAL THICKENED GRADE SUPPORTED SLAB AT

STEEL STAIR

3/4" = 1'-0"

1'-0" 1'-0"

1

5

8"

NOTE:

EXTEND THICKENED SLAB 1'-0" BEYOND EITHER SIDE OF STAIR

STAIR STRINGER, SEE 1/S5.1

L4x4x5/16 W/ 5/8"Ø

EXP ANCHOR W/ 6"

MIN EMBED

WWF

2#5 CONT BOT

4@12"

TYPICAL EXTERIOR 8" CMU WALL FOOTING

3/4" = 1'-0"

1

5

8" 8" 8"

8"

MIN

1'-0

"

T/SLAB EL

CMU WALL

DOWEL TO MATCH

VERT WALL REINF

ALTERNATE HOOKS

3#5 CONT



GRADE AND AT16" ABOVE

GRADE

BOND BREAKER

#4 CONT

WWF

F2 2'-6"x2'-6"x12" 4#4 E.W. TOP & BOTTOM

TYPICAL GRADE SUPPORTED SLAB AT NON

LOAD-BEARING CMU WALL

3/4" = 1'-0"

1

5

8

6"6"

NON LOAD-BEARING WALLS

2'-0

"

T/SLAB EL

WWF

2#5 CONT BOT

CMU WALL

@4 DOWELS W/ STD 90

HOOK @48" ALTERNATE

HOOK

T/FTG EL

EXTERIOR CANTILEVERED 8" CMU WALL FOOTING

3/4" = 1'-0"

1

5

8" 8" 8"

1'-0

"

CMU WALL

DOWEL TO MATCH

VERT WALL REINF

ALTERNATE HOOKS

3#5 CONT



GRADE AND AT16" ABOVE

GRADE

T/FTG EL

8" U-BLOCK FULLY

GROUTED W/ 1#5 CONT.

3'-4

"



(770) 416-7511

www.mackcain.com









DESIGNED BY:

DRAWN BY:

CHECKED BY:

APPROVED BY:

PROJECT NO.

SHEET

SCALE:

DATE:

RE

LE

AS

ED

F

OR

C

ON

ST

RU

CT

IO

N

150536

No. Date



3301 R

OF

F A

VE

NU

E

MA

CO

N, G

A 31204

09/30/16

HJ

BCR

HJ

HJ



Phone: (770)416-7511Fax: (770)416-6759



Description

DRAWINGS SCHEDULE


o | 770.368.1399f | 770.368.1944

w | www.fg-inc.net

S3.1

1

S3.1

2

S3.1

6

S3.1

5

S3.1

9

S3.1

13

S3.1

18

S3.1

14

S3.1

10

AS SHOWN

S3.1

FOUNDATION

DETAILS

S3.1

17

brucem

Line

brucem

Text Box

76

TYPICAL REINFORCING AT 8" LOAD BEARING CMU WALL

3/4" = 1'-0"

AT INTERSECTION

W/ INTERIOR WALL

E

C

AT CORNERSAT JAMBS

A

B

AT BEAM / TRUSS BEARING

AT CONTROL JOINT

D

SEALANT FLUSH W/

MORTAR JOINT

WIDE FLANGE

NEOPRENE

CONTROL JOINT

MATERIAL

#5 VERT TYP

3#5 VERT TYP

CUT HORIZ JOINT

REINF AT CONTROL

JOINT

1#5 EA SIDE

2#5 VERT.

3#5 EA SIDE FOR

OPENINGS GREATER

THAN 8'-0" WIDE

2#5 EA SIDE FOR

OPENINGS 4'-0" TO 8'-0"

1#5 EA SIDE FOR

OPENINGS 4'-0"

WIDE OR LESS

TYPICAL REINFORCING CMU WALL

3/4" = 1'-0"

NO

TE

1

NO

TE

1

AS

R

EQ

UIR

ED

SE

E P

LA

N

AN

D S

EC

TIO

NS

NO

TE

*

NO

TE

*

NO

TE

*

* MASONRY LAP SCHEDULE

#5=30"

NOTE

1. USE 4-0 LIFTS FOR BAR SIZES #3 THROUGH #6,

USE 6-0 LIFTS FOR BAR SIZES #7 AND ABOVE

2. FOR FOOTING AND ADDITIONAL REINFORCING,

REFER TO PLANS AND SECTIONS

JOINT REINF AT 16"

DOWELS TO MATCH VERT REINF, UNO

FILL ALL CELLS SOLID W/

GROUT THAT REQUIRE

VERT REINF AND ALL

CELLS BELOW GRADE

TYPICAL REINFORCING AT CMU WALL OPENING

3/4" = 1'-0"

2'-0"

RO

UG

H O

PE

NIN

G

4"8"

REINF AND GROUT SOLID

1/2 OF VERT REINF

INTERRUPTED BY OPNG

SEE 10/S4.1

FOR SIZE

AND REINF

STANDARD LINTEL SCHEDULE

3/4" = 1'-0"

STANDARD LINTEL SCHEDULE

OPENINGS UP TO 6'-0"

8"x8" U-BLOCK W/ 1#5 T&B

8" BLOCK 8"x8" CONC W/ 2#4 T&B

8" BLOCK 8"x8" CONC W/ 2#4 T&B

8"x16" U-BLOCK W/ 1#6 T&B

WALL SIZE LINTEL TYPE REMARKS


8" BLOCK 8"x8" CONC W/ 2#4 T&B #3 STIR @ 7" CONT

TYPICAL CMU WALL AT BEAM BEARING

3/4" = 1'-0"

SECTIONELEVATION

PLAN

PARALLEL TO WALL

PLAN

PERPENDICULAR TO WALL

CUT CMU AT BRG AS REQD FOR T/BEAM

SEE ? FOR VERT REINF AT JAMB

AND BEARING CONDITIONS

BRG PL 3/8"x7"x1'-0" (WITH

SLOTTED HOLES) WITH (2) 5/8"

DIA x 8" LONG ANCHOR BOLTS

USE THISS CONN ONE

END ONLY AT BEAMS

LONGER THAN 25'-0"

L1-1/2 x 1-1/2 x 3/16

T/BEAM EL


TYPICAL CMU PILASTER

3/4" = 1'-0"

2'-0"

8"

ALTERNATE COURSES

4#4 TYP. PROVIDE

DOWELS INTO FTG TO

MATCH VERT. REINF

#3 TIES @ 8"

O.C. TYP.

135° HOOK TYP.

P1

#4=26"



(770) 416-7511

www.mackcain.com









DESIGNED BY:

DRAWN BY:

CHECKED BY:

APPROVED BY:

PROJECT NO.

SHEET

SCALE:

DATE:

RE

LE

AS

ED

F

OR

C

ON

ST

RU

CT

IO

N

150536

No. Date



3301 R

OF

F A

VE

NU

E

MA

CO

N, G

A 31204

09/30/16

HJ

BCR

HJ

HJ



Phone: (770)416-7511Fax: (770)416-6759



Description

DRAWINGS SCHEDULE


o | 770.368.1399f | 770.368.1944

w | www.fg-inc.net

S4.1

1

S4.1

2

S4.1

6

S4.1

5

S4.1

9

S4.1

10

AS SHOWN

S4.1

MASONRY

DETAILS

brucem

Line

brucem

Text Box

77

TYPICAL ROOF DECK ATTACHMENT (36" WIDE SHEET)

3/4" = 1'-0"

CL OF END

SUPPORT

CL OF

INTERMEDIATE

SUPPORT

TYPICAL FRAMING AT ROOF DECK OPENING

3/4" = 1'-0"

CO

OR

D O

PN

G S

IZ

E

W/ A

RC

H A

ND

M

EC

H

COORD OPNG SIZE

W/ ARCH AND MECH

TYP

3/16

3/16

3/16

SE

E A

BO

VE

NOTE: FOR SPANS GREATER THAN 5'-0" USE L6x3 1/2x5/16 (LLV)

TYPICAL EXTERIOR ROOF DECK AT DECK EDGE

3/4" = 1'-0"

3"@12"

8"

8"

TYPICAL STAIR TREAD DIAGRAM

3/4" = 1'-0"

1"

T/CONC

TYPICAL STAIR AT CONCRETE SLAB

3/4" = 1'-0"

2"

1"

RIS

ER

1

"

W

L

T

Y

P

T/CONC

TYPICAL HOLLOW PRECAST FLOOR PANEL AT 8" CMU

WALL - PERPENDICULAR

3/4" = 1'-0"

6"

TYPICAL DETAIL BETWEEN HOLLOW CORE SLABS

3/4" = 1'-0"

TYPICAL HOLLOW PRECAST FLOOR PANEL AT 8" CMU

WALL - PARALLEL

3/4" = 1'-0"

3 4

" C

LR

.

TYPICAL HOLLOW PRECAST FLOOR PANEL AT

CANTILEVER

3/4" = 1'-0"


OVERHANG

3/4" = 1'-0"

6"

6"

6"

SEE PLAN

6"

1'-4" MAX

ROOF DIAPHRAGM DETAIL

3/4" = 1'-0"

L3-1/2x3-1/2x1/4 x 0'-5"

L3x3x1/4

L3x3x1/4

(7) 5/8" DIA PUDDLE

WELDS AT SUPPORTS

5/8" DIA PUDDLE WELDS

W/ 14 GA WELD WASHERS

@ 12" AT PERIMETER OF

BUILDING

36" WIDE SHEET

METAL DECK

ROOF DECK, SEE PLAN FOR

SPAN DIRECTION

5/16" BENT PL CONT

3/8" OUTRIGGER PL

@ 3'-0" O.C.

HEADER BY PRECAST

MFR. BEAR ON MASONRY

WALL EACH END

CHANNEL STRINGER

METAL CLOSURE PLATE

CHANNEL STRINGER

SEE 10/S3.1

1/4" CLOSURE PL, TYP

CONT. U-BLOCK FILLED

SOLID AND REINF. W/ 1#5

TOP AND BOTTOM CONT.

DOWEL INTO 2"

CONCRETE TOPPING

L3-1/2x3-1/2x1/4

x 0'-5"

#10 SELF TAPPING

SCREWS @ 12" AT

SIDE LAPS

NON-SLIP NOSING

1/8"x2" MASONITE BEARING

STRIP CONT. UNDER BEARING

END OF ALL PRECAST

HOLLOW CORE SLAB. TYP.

3000 PSI GROUT




#4@4'-0" O.C. MAX.

(IN KEYWAY)



END OF ALL PRECAST





TOP REINFORCING DESIGNED

BY PRECAST MANUFACTURER



END OF ALL PRECAST


#4x1'-0" DOWEL DRILL AND

GROUT IN KEYWAYS @ 48"

O.C. AFTER PLANK ERECTION






END OF ALL PRECAST


#4x1'-0" DOWEL DRILL AND

GROUT IN KEYWAYS @ 48"

O.C. AFTER PLANK ERECTION

#4@4'-0" O.C., GROUTED

INTO POCKETS

8d@6" AT

NON-CONTINUOUS

PANEL EDGES

PLYWOOD DIAPHRAGM

(STAGGER SHEETS AS

SHOWN)

SIMPSON PSCL

(PANEL SHEATHING CLIPS)

AT MID-SPAN WHEN SPAN IS

GREATER THEN 16"

8d@12" ALONG

INTERMEDIATE FRAMING

MEMBERS (TYP.)

LIGHT GAUGE METAL

TRUSSES SEE PLAN

GROUT SOLID CORE

SECTION AT ROOF DECK EDGE

3/4" = 1'-0"

1/4" BENT PLATE CONT

3-12"

SEE

ARCH

SUPPORT BEAM SEE PLAN

SEE PLAN FOR ROOF

DECK SPAN AND

CONNECTION

6" HOLLOW CORE PRECAST

CONCRETE SLAB W/ 2"

CONCRETE TOPPING

DOWEL INTO 2"

CONCRETE TOPPING

6" HOLLOW CORE PRECAST

CONCRETE SLAB W/ 2"

CONCRETE TOPPING

2"

2"

TYPICAL LOAD BEARING WALL HEADER SECTION

NOT TO SCALE

HEADER SECTION

ELEVATION

METAL STUD

TRACK

METAL STUD

TOP PLATE

HEADER

DOUBLE STUDS

METAL STUD

SILL PLATE

(2) 10" DEEP, 1 5/8"

LEG METAL STUDS

ALL UNPUNCHED

AND CONTINUOUS

METAL STUD

CLIP

TYPICAL METAL STUD WALL SECTION

3/4" = 1'-0"

SEE ARCH FOR SLOPE

5/8" PLYWOOD

SHEATHING

CONNECTION TO LIGHT

GAUGE MEMBER. SEE

COLD FORMED STEEL

NOTE 1 ON S0.1.

1/2" PLYWOOD SHEATHING

CONNECTED TO METAL STUDS

WITH #10 SELF-TAPPING SCREWS

AT 6" O.C. AT PANEL EDGES AND

INTERMEDIATE SUPPORTS.

HOLLOW CORE SLAB

600T250-54 (MIN) CONT. DEEP

TRACK. ATTACH TO SLAB W/ (2)

0.157"Ø HILTI X-U P.D.F'S @

EACH STUD LOCATION WITH

MIN 1" EMBEDMENT.

6" METAL STUD

@ 16" O.C.

#4@4'-0" O.C.

1#5 CONT.

1#5 CONT.

3/16"

TYPICAL TRUSS BEARING SECTION AT STEEL BEAM

AT SPLASH PAD

3/4" = 1'-0"

5/8" PLYWOOD

SHEATHING

CONNECTION OF TRUSS

TO NAILER BY TRUSS

MANUFACTURER

TYPICAL TRUSS BEARING SECTION AT SPLASH PAD

3/4" = 1'-0"

LIGHT GAUGE

METAL TRUSS

5

12

BEAM, SEE PLAN

2x6 WOOD NAILER CONT.

CONNECTED TO BEAM WITH

1/2"Ø CARRIAGE BOLTS @

2'-0" O.C. STAGGERED

CL BEAM

CL BEAM

CL WALL

CL BEAM

5/8" PLYWOOD

SHEATHING

LIGHT GAUGE

METAL TRUSS

5

12

CONNECTION OF TRUSS

TO NAILER BY TRUSS

MANUFACTURER

2x6 WOOD NAILER CONT.

W/ 5/8"Øx12" ANCHOR

BOLT @ 2'-0" O.C.

CONT. BOND BEAM FILLED

SOLID WITH GROUT AND

REINF. W/ 2#5 CONT.

CMU WALL, SEE 1&5/S4.1.


OVERHANG AND STEEL DECK BEARING

3/4" = 1'-0"






END OF ALL PRECAST


HOOK VERTICAL

BAR AT TOP

1#5 CONT.

EMBED PL BY PRECAST MFR.

CL BEAM

BEAM,

SEE PLAN

L6x3x5/16 CONT.

(LLH)

6"

3-123/16"

3-123/16"

DECK

BRG EL

(2) 6" DEEP, 1 5/8"

LEG METAL STUDS

ALL UNPUNCHED

AND CONTINUOUS

TREAD

NOTE: SEE ARCH FOR HANDRAIL



(770) 416-7511

www.mackcain.com









DESIGNED BY:

DRAWN BY:

CHECKED BY:

APPROVED BY:

PROJECT NO.

SHEET

SCALE:

DATE:

RE

LE

AS

ED

F

OR

C

ON

ST

RU

CT

IO

N

150536

No. Date



3301 R

OF

F A

VE

NU

E

MA

CO

N, G

A 31204

09/30/16

HJ

BCR

HJ

HJ



Phone: (770)416-7511Fax: (770)416-6759



Description

DRAWINGS SCHEDULE


o | 770.368.1399f | 770.368.1944

w | www.fg-inc.net

S5.1

1

S5.1

2

S5.1

6

S5.1

5

S5.1

9

S5.1

13

S5.1

17

S5.1

18

S5.1

14

S5.1

19

S5.1

15

S5.1

11

S5.1

10

S5.1

7

S5.1

3

S5.1

8

S5.1

20

AS SHOWN

S5.1

FRAMING

DETAILS

brucem

Line

brucem

Text Box

78

CONCESSION STAND TRUSS PROFILES

3/8" = 1'-0"

12

5

METAL STUD

WALL

12

5

METAL STUD WALL

12

5

METAL STUD WALL

BEAM, SEE PLAN

PRE-ENGINEERED

METAL TRUSS

12

5

12

5

PRE-ENGINEERED

METAL TRUSS

12

5

METAL STUD WALL

PRE-ENGINEERED

METAL TRUSS

PRE-ENGINEERED

METAL TRUSS

12

5

12

5

12

5

12

5

12

5

12

5

12

5

PRE-ENGINEERED

METAL TRUSS

PRE-ENGINEERED

METAL TRUSS

PRE-ENGINEERED

METAL TRUSS

MASONRY WALL

MASONRY WALL

MASONRY WALL

MASONRY WALL/

STEEL BEAM

T1

T2

T3

T6

T5

PRE-ENGINEERED

METAL TRUSS

T4

SPLASH PAD TRUSS PROFILES

3/8" = 1'-0"

T2

T4

T1

T3

T6

T5



(770) 416-7511

www.mackcain.com









DESIGNED BY:

DRAWN BY:

CHECKED BY:

APPROVED BY:

PROJECT NO.

SHEET

SCALE:

DATE:

RE

LE

AS

ED

F

OR

C

ON

ST

RU

CT

IO

N

150536

No. Date



3301 R

OF

F A

VE

NU

E

MA

CO

N, G

A 31204

09/30/16

HJ

BCR

HJ

HJ



Phone: (770)416-7511Fax: (770)416-6759



Description

DRAWINGS SCHEDULE


o | 770.368.1399f | 770.368.1944

w | www.fg-inc.net

S5.2

1

S5.2

2

AS SHOWN

S5.2

TRUSS

PROFILES

brucem

Line

brucem

Text Box

79

BID ALTERNATES TO BASE BID FORM# Bid Item # Name of Bid Alternate

1 MUSCO Lighting substitution for Qualite Desgin

2 MUSCO Lightng redesign

3 Sports Lighting and Scoreboard Deduction

4

5

6

7

8

9

10

Contractor may provide Bid Alternates to any item he feels would provide a better alter Contractor shall include the corresponding bid item number from the Construction Bid It Difference in alternate and base bid for the same item shall be shown in column E. Alternate form shall be attached to the Base Bid Form. Explanations, details, data, and Contractor may extend the form to include additional alternates that he desires to includ

Bid Amount Difference in Base Bid

$ $

$ $

$

$ $

$ $

$ $

$ $

$ $

$ $

$ $

native than what is specified by using this form. tems Scheudle for each alternate in column B.

breakdowns should be incuded in the bid package. de

Lighting Fixture Schedule_0117 Page 1 of 1

FREEDOM PARK GIRLS SOFTBALL FIELDS # 19 SPORTS LIGHTING FIXTURE SCHEDULE Jan 2017

QTY. MANUFACTURER & CATALOG NUMBER MOUNTING NO./LAMPS LOAD UNIT PRICE TOTAL11 Beacon Products #VP-L-96NB-280-4K-T4-480-PCR-TL-BLC-RA-BBT 25' POLE LED ARRAY 300W $0.00 $0.00

Spaulding #SSA-25-50-B-AX-BL POLE6 Beacon Products #VP-L-96NB-280-4K-T4-480-PCR-TL-RA-BBT 25' POLE LED ARRAY 600W $0.00 $0.00

Spaulding #SSA-25-50-B-CX-BL POLE12 Beacon Products #VP-L-96NB-280-4K-T3-480-PCR-TL-RA-BBT 25' POLE LED ARRAY 300W $0.00 $0.00

Spaulding #SSA-25-50-B-AX-BL POLE1 Electrical Service to Connect Concession Building and Panel $0.00 $0.001 Electrical Service to Connect Splash Pad Building and Panel $0.00 $0.004 Electrical Service to Scoreboards $0.00 $0.00

27 Pole Foundation 3 - See Detail 3/SE.3 $0.00 $0.002 Pole Foundation 4 - See Detail 4/SE.3 $0.00 $0.001 Electical service, wiring and connectors complete $0.00 $0.00

TOTAL Transfere this total to line item # 19 on theconstruction Bid Items Schedule $0.00

# 26 Site Lighting Fixture Schedule See Sheets SE.1-SE.3 Jan 2017Fixture Type of Fixture Qty Unit Unit $ Total $

A. Type A 11 ea $0.00 $0.00B. Type B 6 ea $0.00 $0.00C. Type C 12 ea $0.00 $0.00D. Electrical Service to Connect Concession Building and Panel 1 job $0.00 $0.00E. Electrical Service to Connect Splash Pad Building and Panel 1 job $0.00 $0.00F. Electrical Service to Scoreboards 1 job $0.00 $0.00G. Pole Foundation 3 - See Detail 3/SE.3 1 job $0.00 $0.00H. Pole Foundation 4 - See Detail 4/SE.3 1 job $0.00 $0.00I Electrical Service to system - complete 1 job $0.00 $0.00

TOTAL Transfer this total to item # 26 on the Construction Bid Items Scheudule $0.00

THIS SPREADSHEET IS AVAILABLE IN ELECTRONIC (*.XLXS) FORMAT BY CONTACTING MACK CAIN: [email protected]

Macon-Bibb County Government · Macon-Bibb County Government . ... FREESTANDING, MODEL: AH-425,...

Documents

Transcript of Macon-Bibb County Government · Macon-Bibb County Government . ... FREESTANDING, MODEL: AH-425,...