M5NM1I · 2019. 3. 29. · USB 2.0 Port The USB port supports the USB 2.0 specification. Use this...

M5NM1IIntel® Atom™ D2500/D2550/D2560 processor motherboard

User's ManualRev. 1001

Copyright© 2012 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.The trademarks mentioned in this manual are legally registered to their respective owners.

DisclaimerInformation in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.

Documentation ClassificationsIn order to assist in the use of this product, GIGABYTE provides the following types of documentation: For detailed product information, carefully read the User's Manual.

For product-related information, check on our website at: http://www.gigabyte.com

- 3 -

Table of Contents

Box Contents ...................................................................................................................4M5NM1I Motherboard Layout ..........................................................................................5Chapter 1 Hardware Installation .....................................................................................7

1-1 Installation Precautions .................................................................................... 71-2 ProductSpecifications ...................................................................................... 81-3 Installing the Memory ..................................................................................... 10

1-3-1 DualChannelMemoryConfiguration .....................................................................101-3-2 Installing a Memory ...............................................................................................11

1-4 Back Panel Connectors .................................................................................. 121-5 Internal Connectors ........................................................................................ 13

Chapter 2 BIOS Setup ..................................................................................................262-1 The Main Menu .............................................................................................. 282-2 Advanced Menu ............................................................................................. 30

2-2-1 CPUConfiguration ..................................................................................................312-2-2 SATAConfiguration.................................................................................................332-2-3 USBConfiguration ..................................................................................................352-2-4 F81214SuperIOConfiguration ..............................................................................372-2-5 H/W Monitor ............................................................................................................39

2-3 Chipset Menu ................................................................................................. 402-4 Boot Menu ...................................................................................................... 412-5 Security Menu ................................................................................................ 432-6 Save & Exit Menu ........................................................................................... 44

- 4 -

Box Contents M5NM1I motherboard Driver CD Two SATA cables I/O Shield

• The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.• The motherboard image is for reference only.

- 5 -

M5NM1I Motherboard Layout

8

109

13

14151617

18

2224

27

28

29

30

31

34

35

36

1926 25

3233

23

1112

2021

1 2 3 4 5 6 7

- 6 -

Item Code Description1 LINE_IN Audio Line In port2 LINE_OUT Audio Line Out port3 R_USB1 USB 2.0 ports4 R_USB2 USB 2.0 ports5 HDMI HDMI port6 LAN RJ45 LAN port7 DC_IN DC In power connector8 ATX_19V 2 pin power connector9 MIN_PCIE1 Mini PCi Express connector10 F_USB2 Front USB connector11 COM2 Serial port cable header12 COM1 Serial port cable header13 TPM TPM moudle header14 LAN_LED LAN LED header15 BL_SW Back Light switch header16 F_PANEL Front panel header17 WF_LED WF LED header18 SATAII_1/SATAII_2 SATA cable connectors19 HDD_PWR Hard disk power connector20 F_USB2_1 Front USB connector21 F_AUDIO Audio cable connector22 CPU_FAN CPU fan connector23 CPU Embedded porcessor24 SYS_FAN System fan connector25 VGA_PH VGA cable connector26 BATTERY Battery socket27 CLR_CMOS Clear CMOS jumper28 PCH Intel 82NM10 chipset29 LVDS_EN LVDS Enable/Disable jumper30 FPD Flat Panel Display connector31 EDP LVDS connector32 DMIC_CON Digital Mic header33 WEB_CON WEBCAM header34 SPEK Speaker cable connector35 SO_DIMM1 DDR3 SO-DIMM slot (channel 1)36 SO_DIMM2 DDR3 SO-DIMM slot (channel 2)

- 7 - Hardware Installation

1-1 Installation PrecautionsThe motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures: • Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation. • Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components. • When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely. • When handling the motherboard, avoid touching any metal leads or connectors. • It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic com-

ponents such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.

• Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power sup-ply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your hard-ware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.

• Do not place the computer system on an uneven surface. • Do not place the computer system in a high-temperature environment. • Turning on the computer power during the installation process can lead to damage to sys-

tem components as well as physical harm to the user. • If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certified computer technician.

Chapter 1 Hardware Installation

Hardware Installation - 8 -

1-2 ProductSpecificationsCPU � Supports single Intel® Atom D2500/D2500/D2560 processors

� Supports 1.8GHz

Chipset � Intel® 82NM10 chipset

Memory � 2 x 1.5V DDR3 SO-DIMM slots � Max. to 8GB (4GB x 2) � Dual channel architecture � Support for DDR3 800/1066 MHz

Display � 1 x HDMI 1.3 out � 1 x LVDS connector

Audio � Realtek ALC887 codec � High Definition Audio � 2 Channel / SPDIF out

LAN � 1 x Realtek RTL8111E supports 10/100/1000 Mbps

Expansion Slots � 1 x Mini PCI Express slot (Half size)

Onboard Graphics

� Build in Intel® processor

Storage Interface � 2 x SATA 3Gb/s connectors

USB � 4 x USB 2.0 ports (back panel) � 2 x USB 2.0/1.1 headers

Internal Connectors

� 1 x 2-pin power connector � 1 x TPM header � 2 x SATA 3Gb/s connectors � 1 x HDD power connector � 1 x CPU fan header � 1 x System fan header � 1 x Front panel header � 1 x Audio header � 2 x USB 2.0 headers � 1 x Speaker header � 1 x LVDS connector � 1 x FPD connector � 1 x Web CAM header � 1 x DMIC header � 1 x Serial port cable headers � 1 x VGA cable connector


Back Panel Connectors

� 1 x DC-IN � 1 x RJ-45 port � 1 x HDMI port � 4 x USB 2.0 ports � 1 x Audio Line In � 1 x Audio Line Out

I/O Controller � iTE IT8773 chip

Hardware Monitor

� CPU/System temperature detection � CPU fan speed detection

BIOS � 1 x 64 Mbit flash � AMI BIOS

Form Factor � Mini ITX Form Factor; 170cm x 170cm

* GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.


1-3-1 DualChannelMemoryConfigurationThis motherboard provides two DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. En-abling Dual Channel memory mode will double the original memory bandwidth.

1-3 InstallingtheMemoryRead the following guidelines before you begin to install the memory:• Make sure that the motherboard supports the memory. It is recommended that memory of the

same capacity, brand, speed, and chips be used.• Always turn off the computer and unplug the power cord from the power outlet before installing

the memory to prevent hardware damage.• Memory modules have a foolproof design. A memory module can be installed in only one

direction. If you are unable to insert the memory, switch the direction.

NOTE!• DIMM must be populated in order starting from SO_DIMM2 socket. For Dual-channel operation,

DIMMs must be installed in matched pairs.

SO_DIMM1SO_DIMM2


1-3-2 InstallingaMemoryBeforeinstallingamemorymodule,makesuretoturnoffthecomputerandunplugthepowercordfromthepoweroutlettopreventdamagetothememorymodule.BesuretoinstallDDR3DIMMsonthismotherboard.

Installation Step:Step 1. Align the memory with the DIMM module and insert the DIMM memory module into the DIM slot. Please note that memory module has a foolproof insertion design. A memory module can be installed In only one direction.Step 2. Push down the memory and seat it firmly.Step 3. Reverse the installation steps when you wish to remove the DIMM module.

2

1


1-4 BackPanelConnectors

DCPowerJackConnect the DC power to this port.RJ-45 LAN PortThe Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.HDMI PortThe HDMI (High-Definition Multimedia Interface) provides an all-digital audio/video interface totransmit the uncompressed audio/video signals and is HDCP compliant. Connect the HDMIaudio/video device to this port. The HDMI Technology can support a maximum resolution of1920x1080p but the actual resolutions supported depend on the monitor being used.

USB2.0PortThe USB port supports the USB 2.0 specification. Use this port for USB devices such as a USB key-board/mouse, USB printer, USB flash drive and etc.LineOutJack(Green)The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.LineInJack(Blue)The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

• When After installing the HDMI device, make sure the default device for sound playback is the HDMI device. (The item name may differ by operating system. Refer the figures below for details.), and enter BIOS Setup, then set Onboard VGA output connect to D-SUB/ HDMI under Advanced BIOS Features..• Please note the HDMI audio output only supports AC3, DTS and 2-channel-LPCM formats. (AC3 and DTS require the use of an external decoder for decoding.)

• When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.

• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.

Activity LEDConnection/Speed LED

LAN Port

Activity LED:Connection/Speed LED:State DescriptionOrange 1 Gbps data rateGreen 100 Mbps data rateOff 10 Mbps data rate

State DescriptionBlinking Data transmission or receiving is occurringOff No data transmission or receiving is occurring


1-5 Internal Connectors

Read the following guidelines before connecting external devices:• First make sure your devices are compliant with the connectors you wish to connect.• Before installing the devices, be sure to turn off the devices and your computer. Unplug the

power cord from the power outlet to prevent damage to the devices.• After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

1) F_PANEL 2) ATX_19V 3) TPM 4) F_USB2_1 5) F_USB2_2 6) F_AUDIO 7) FPD 8) SATAII_0/1 9) HDD_PWR 10) VGA_PH 11) CPU_FAN 12) SYS_FAN

13) COM1 14) COM2 15) SPEK 16) DMIC_CON 17) WEB_CON 18) EDP(LVDSConnector) 19) BATTERY 20) CLR_CMOS 21) BL_SW 22) LAN_LED 23) WF_LED 24) LVDS_EN4

8

10 1112 9

1314

18

1617

15

20

24

2221

23

19

1

2

3

5

46

7


The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.

10 9

2 1

1) F_PANEL(FrontPanelHeader) Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status

indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

Pin No. Signal Name Definition 1 HD+ Hard Disk LED Signal anode (+) 2 MPD+ Power LED Signal anode (+) 3 HD- Hard Disk LED Signal cathode(-) 4 MPD- Power LED Signal cathode(-) 5 GND Ground 6 PW+ Power Button anode (+) 7 RST Reset Button 8 PW- Power Button cathode(-) 9 WF_LED Wireless LAN active LED Signal


2) ATX_19V(2PinPowerConnector)

1

2

Pin No. Definition 1 GND 2 +19V

3) TPM(TPMHeader)

Pin No. Definition 1 CLK_33M_TPM 2 GND 3 LPC_LFRAME_N 4 NC 5 LPC_RST_TPM 6 NC 7 LPC_LAD3 8 LPC_LAD2 9 P3V3 10 LPC_LAD1

Pin No. Definition 11 LPC_LAD0 12 GND 13 NC 14 NC 15 P_3V3_AUX 16 LPC_SERIRQ 17 GND 18 GND 19 P3V3 20 NC

1

19

2

20


4) F_USB2_1(USBHeaders) The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

5) F_USB2_2(USBHeaders)

10

9

2

1

14

Pin No. Definition 1 VCC 2 VCC 3 USB3- 4 USB2- 5 USB3+ 6 USB2+ 7 GND 8 GND 9 No Pin 10 NC

Pin No. Definition 1 VCC 2 USB- 3 USB+ 4 GND


10

9

2

1

6) F_AUDIO(FrontPanelAudioHeader) The front panel audio header supports Intel High Definition audio (HD) and AC'97 audio. You may connect

your chassis front panel audio module to this header. Make sure the wire assignments of the module con-nector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.

• The front panel audio header supports HD audio by default. • Audio signals wil l be present on both of the front and back panel audio connections

simultaneously. • Some chassis provide a front panel audio module that has separated connectors on each wire

instead of a single plug. For information about connecting the front panel audio module that has different wire assignments, please contact the chassis manufacturer.

Pin No. Definition 1 MIC_L 2 GND 3 F_MIC_R 4 GPIO_DET 5 F_LINE_R 6 F_MIC_JD 7 GND 8 No Pin 9 F_LINE_L 10 F_LINE_JD

7)FPD(FlatPanelDisplayHeaders) Flat Panel Display (FPD)is a high-speed interface connecting the output of a video controller in a laptop

computer, computer monitor or LCD television set to the display panel. Most laptops, LCD computer monitors and LCD TVs use this interface internally.

The headers conform to FPD specification.

1

8

Pin No. Definition 1 Backlight Enable 2 Backlight control 3 FPD_19V 4 FPD_19V 5 GND 6 GND 7 Brighrness Up 8 Brighrness Down


8) SATAII_0/SATAII_1(SATA3Gb/sConnectors) The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.

Each SATA connector supports a single SATA device.

9) HDD_PWR(HDDPowerConnector)

Pin No. Definition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND

Pin No. Definition 1 +12V 2 GND 3 VCC 4 VCC 5 GND

1

1

SATAII_0 SATAII_1

7

5

DEBUG PORT

DEBUG PORT


11/12)CPU_FAN/SYS_FAN(CPUFan/SystemFanHeaders) The motherboard has a 4-pin CPU fan header (CPU_FAN) and a 4-pin System fan header (SYS_FAN)

header. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The motherboard supports CPU fan speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.

• These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.

Pin No. Definition 1 GND 2 +12V 3 Sense 4 Speed Control

1

1

CPU_FAN

SYS_FAN

DEBUG PORT

DEBUG PORT

10)VGA_PH(VGACableConnector)

Pin No. Definition 1 RED 2 DDCSDA 3 GND 4 DDSCL 5 GREEN 6 GND 7 GREEN 8 DDC Clock 9 BLUE 10 DDC Data 11 NC 12 NC

1 112 12


13/14)COM1/COm2(SerialPortHeaders) The COM header can provide one serial port via an optional COM port cable. For purchasing the op-

tional COM port cable, please contact the local dealer.

F_PANEL

F_PANEL

F_AUDIO

F_AUDIO

F_USB

COMB

MODEM

Smart Card Reader

SPDIF

AUX_INCD_IN

Secure Gigital /Memory Stick

Serial ATA

F_USBF_1394

CPU_FANSYS_FANPWR_FAN

NB_FAN

Power

WOL

SUR_CEN

IR/CIR

F_PANEL

F_PANEL

PWR_LED

CLR_CMOSBIOS_WP

CLR_CMOSBIOS_WP

CI

DPVRM

CLR_PWD

FDD

ATX

ATX_12V

IDE

IR

COMB

SPDIF_IO

F1_1394 F2_1394

GAME SMB_CONNF_AUDIO(NEW)

F1_1394

1

9

2

10

Pin No. Definition 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 10 No Pin

15) SPEK(SpeakerHeaders)

Pin No. Definition 1 SP_OUTR- 2 SP_OUTR+ 3 SP_OUTL+ 4 SP_OUTL-

14


17) DMIC_CON(DMICHeaders)

Pin No. Definition 1 Power 2 DMICDATA 3 GND 4 DMICCLK

16) WEB_CON(WebCAMHeader)

Pin No. Definition 1 Power 2 USB D- 3 USB D+ 4 GND

14

14


18) EDP(LVDSHeader) LVDS stands for Low-voltage differential signaling, which uses high-speed analog circuit techniques to provide multigigabit data transfers on copper interconnects and is a generic interface standard for high-speed data transmission.

Pin No. Definition 1 ODD_Lane3_P 2 ODD_Lane3_N 3 ODD_Lane2_P 4 ODD_Lane2_N 5 ODD_Lane1_P 6 ODD_Lane1_N 7 ODD_Lane0_P 8 ODD_Lane0_N 9 EVEN_Lane3_P 10 EVEN_Lane3_N 11 EVEN_Lane2_P 12 EVEN_Lane2_N 13 EVEN_Lane1_P 14 EVEN_Lane1_N 15 EVEN_Lane0_P 16 EVEN_Lane0_N 17 EDID_GND 18 LCD_VCC 19 LCD_VCC 20 LCD_VCC

Pin No. Definition 21 NC 22 EDID_3.3V 23 LCD_GND 24 LCD_GND 25 LCD_GND 26 ODD_CLK_P 27 ODD_CLK_N 28 BLKT_GND 29 BLKT_GND 30 BLKT_GND 31 EDID_CLK 32 BLKT_ENABLE 33 BLKT_PWM_DIM 34 EVEN_CLK_P 35 EVEN_CLK_N 36 BLKT_PWR 37 BLKT_PWR 38 BLKT_PWR 39 NC 40 EDID_DATA

1

40


19) BATTERY(Battery) The battery provides power to keep the values (such as BIOS configurations, date, and time information)

in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery: 1. Turn off your computer and unplug the power cord.2. Gently remove the battery from the battery holder and wait

for one minute. (Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder, making them short for 5 seconds.)

3. Replace the battery. 4. Plug in the power cord and restart your computer.

• Always turn off your computer and unplug the power cord before replacing the battery.• Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model.• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery

model.• When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery (the positive side

should face up).• Used batteries must be handled in accordance with local environmental regulations.

20) CLR_CMOS(ClearingCMOSJumper) Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset

the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds.

Open: Normal operation (Default setting)

Close: Clear CMOS data

• After clearing the CMOS values and before turning on your computer, be sure to remove the jumper cap from the jumper. Failure to do so may cause damage to the motherboard.


21) BL_SW(BackLightSwitch)

22) LAN_LED(LANLEDHeader)

Pin No. Definition 1 BL_DOWN 2 BL_UP

1 2

Pin No. Definition 1 GND 2 H_-ACT_LED

1 2


23) WF_LED(WirelessLEDHeader)

24) LVDS_EN(LVDSEnableJumper)

1

1

1-2 Close: Enable onabord LVDS device. (Default setting)

2-3 Close: Disable onabord LVDS device.

Pin No. Definition 1 GND 2 LED_WLAN#

1 2

BIOS Setup - 26 -

Chapter 2 BIOS SetupBIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup, saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS.

To access the BIOS Setup program, press the <DEL> key during the POST when the power is turned on.

• BIOS flashing is potentially risky, if you do not encounter problems of using the current BIOS version, it is recommended that you don't flash the BIOS. To flash the BIOS, do it with caution. Inadequate BIOS flashing may result in system malfunction.

• It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values. (Refer to the "Load Optimized Defaults" section in this chapter or introductions of the battery/clearing CMOS jumper in Chapter 1 for how to clear the CMOS values.)

BIOS Setup Program Function Keys <h><i> Move the selection bar to select an item <f><g> Move the selection bar to select the screen <Enter> Execute command or enter the submenu <Esc> Main Menu: Exit the BIOS Setup program Submenus: Exit current submenu <+> Increase the numeric value or make changes <-> Decrease the numeric value or make changes <F1> General Help <F2> Restore the previous BIOS settings for the current submenus <F3> Load the Optimized BIOS default settings for the current submenus <F4> Save all the changes and exit the BIOS Setup program

- 27 - BIOS Setup

Main This setup page includes all the items in standard compatible BIOS. Advanced This setup page includes all the items of AMI BIOS special enhanced features. (ex: Auto detect fan and temperature status, automatically configure hard disk parameters.) Chipset Northbridge and Southbridge additional features configuration. Boot This setup page provides items for configuration of boot sequence. Security Change, set, or disable supervisor and user password. Configuration supervisor password allows you to

restrict access to the system and BIOS Setup. A supervisor password allows you to make changes in BIOS Setup. A user password only allows you to view the BIOS settings but not to make changes. Save & Exit Save all the changes made in the BIOS Setup program to the CMOS and exit BIOS Setup. (Pressing

<F10> can also carry out this task.) Abandon all changes and the previous settings remain in effect. Pressing <Y> to the confirmation

message will exit BIOS Setup. (Pressing <Esc> can also carry out this task.)

BIOS Setup - 28 -

2-1 The Main MenuOnce you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use arrow keys to move among the items and press <Enter> to accept or enter other sub-menu.Main Menu HelpThe on-screen description of a highlighted setup option is displayed on the bottom line of the Main Menu.Submenu HelpWhile in a submenu, press <F1> to display a help screen (General Help) of function keys available for the menu. Press <Esc> to exit the help screen. Help for each item is in the Item Help block on the right side of the submenu.

• If you do not find the settings you want in the Main Menu or a submenu, press <Ctrl>+<F1> to access more advanced options.

• When the system is not stable as usual, select the Restore Defaults item to set your system to its defaults.

• The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.

- 29 - BIOS Setup

BIOS Information BIOS Vendor

Display BIOS vendor information. BIOS Version

Display version number of the BIOS setup utility. Core Version

Display version of the processor. Compliency

Display compliency information. Project Version

Display version number of the project. BIOS Build Date and Time

Displays the date and time when the BIOS setup utility was created. Memory Information Total Memory

Determines how much total memory is present during the POST. System Date

Set the date following the weekday-month-day- year format. System Time

Set the system time following the hour-minute- second format.

BIOS Setup - 30 -

2-2 Advanced MenuThe Advanced menu display submenu options for configuring the function of various hardware components. Select a submenu item, then press Enter to access the related submenu screen.

PCI ROM Priority In case of multiple option ROMs (Legacy ROM and EFI Compatible), specifies what PCI Option ROM to launch. Options available: Legacy ROM/EFI Compatible. Default setting is Legacy ROM.

ACPI Sleep State Select the highest ACPI sleep state the system will enter, when the suspend button is pressed. Suspend Disabled/S1 (CPU Stop Clock)/S3 (Suspend to RAM). Options available: S1(CPU Stop Clock)/S3(Suspend to RAM). Default setting is S3(Suspend to RAM).

- 31 - BIOS Setup

2-2-1 CPUConfiguration

CPUConfiguration CPU Type

Displays the processor type information. EM64T

Displays the processor EM64T support information. CPU Speed

Display the information of the processor speed. System Bus Speed

Display the information of the system bus speed. Ratio Status

Display the processor ratio status. Actual Ratio

Display the processor actual ratio status. Processor Stepping

Display the processor stepping information. Microcode Revision

Display Microcode revision information. L1 Cache RAM

Display the information of L1 Cache RAM. L2 Cache RAM

Display the information of L2 Cache RAM.

BIOS Setup - 32 -

Processor Cores Display the information of the processor core.

Hyper-Threading Displays the processor Hyper-Threading support information.

Execute Disable Bit When this item enabled, the processor prevents the execution of code in data-only memory pages. This provides some protection against buffer overflow attacks. Options available: Enabled/Disabled. Default setting is Enabled.

Limit CPUID Maximum When enabled, the processor will limit the maximum COUID input values to 03h when queried, even if

the processor suppports a higher CPUID input value. When disabled, the processor will return the actual maximum CPUID input value of the processor when

queried. Options available: Enabled/Disabled. Default setting is Disabled.

- 33 - BIOS Setup

2-2-2 SATAConfiguration

SATAConfiguration SATA Port 0/SATA Port 1

The category identifies Serial ATA and mSATA types of hard disk that are installed in the computer. System will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work

properly if you enter improper information for this category. Hard drive information should be labeled on the outside device casing. Enter the appropriate option

based on this information. Type

Auto: Set parameters automatically. (Default setting) CD-ROM: Use for ATAPI CD-ROM drives or double click [Auto] to set all HDD parameters

automatically. ARMD: Use ARMD drive is installed here.

LBA/Large Mode Configure the device type in the specific IDE channel support LBA Mode. Option available: Auto/Disabled. Default setting is Auto.

Block (Multi-Sector Transfer) Configure the information of Multi-Sector Transfer Mode. Auto: The data transfer from and to the device occurs multiple sectors at a time if the device

supports it. Disabled: The data transfer from and to the device occurs one sector at a time. Option available: Auto/Disabled. Default setting is Auto.

BIOS Setup - 34 -

PIO Mode This feature allows you to set the PIO (Programmed Input/Output) mode for the two IDE devices (Master

and Slave drives) attached to that particular IDE channel. Option available: Auto/Disabled. Default setting is Auto.

DMA Mode Configure the DMA mode of the device in the specific IDE channel. Option available: Auto/Disabled. Default setting is Auto.

S.M.A.R.T Mode This feature allows you to set the PIO (Programmed Input/Output) mode for the two IDE devices (Master

and Slave drives) attached to that particular IDE channel. Option available: Auto/Disabled. Default setting is Auto.

32Bit Data Transfer Configure the 32Bit Data Transfer rate. Option available: Auto/Disabled. Default setting is Auto.

ConfigureSATAas Select the on chip SATA type. IDE Mode: When set to IDE, the SATA controller disables its RAID and AHCI functions and runs in the

IDE emulation mode. This is not allowed to access RAID setup utility. RAID Mode: When set to RAID, the SATA controllerenables both its RAID and AHCI functions. You will

be allows access the RAID setup utility at boot time. AHCI Mode: When set to AHCI,the SATA controller enables its AHCI functionality. Then the RAID function is disabled and cannot be access the RAID setup utility at boot time. Options available: IDE/RAID/AHCI/Disabled. Default setting is AHCI Mode.

- 35 - BIOS Setup

2-2-3 USBConfiguration

Legacy USB Support Enables or disables support for legacy USB devices. Options available: Auto/Enabled/Disabled. Default setting is Enabled.

EHCI Hand-off Enable/Disable EHCI Hand-off function. Options available: Enabled/Disabled. Default setting is Enabled.

Port 60/64 Emulation Enable I/O port 60h/64h emulation support. This should be enabled for the complete USB Keyboard

Legacy support for non-USB aware OS. Options available: Enabled/Disabled. Default setting is Disabled.

USB hardware delays and time-out USB transfer time-out

Define USB transfer start unit command timeout. Options available: 1 sec/5 sec/10 sec/20 sec.

Device reset time-out Define USB device reset start unit command timeout. Options available: 1 sec/5 sec/10 sec/20 sec.

Device power-up delay Define USB device powering up start unit command timeout. When this item is set to Manual, you can

press numeric keys to configure desired values. Options available: Auto/Manual.

BIOS Setup - 36 -

Mass Storage Device(Note) This BIOS feature determines if the USB flash drive be treated as a floppy disk drive or a hard drive. Options available: Auto.

(Note) This item is present only if you attach USB types of device.

- 37 - BIOS Setup

2-2-4 F81214SuperIOConfiguration

BIOS Setup - 38 -

F81214SuperIOConfiguration F81214 Second Super IO Chip

Display the mode name of Super IO chip. SerialPort0/1Configuration

When enabled allows you to configure the serial port settings. When set to Disabled, displays no configuration for the serial port. Options available: Enabled/Disabled. Default setting is Enabled.

Device Settings Displays the Serial Port 3/4 base I/O addressand IRQ.

Change Settings Change Serial Port 3/4 device settings. Options available: Auto/IO=3F8; IRQ=4/IO=3F8h; IRQ=3,4,5,6,7,10,11,12/ IO=2F8h; IRQ=3,4,5,6,7,10,11,12 /IO=3E8h; IRQ=3,4,5,6,7,10,11,12/IO=2E8h; IRQ=3,4,5,6,7,10,11,12.

Device Mode Configure Serial Port 0/1 Device Mode. Options available: TBD. Default setting is TBD.

- 39 - BIOS Setup

CPU/System FAN Fail Detect Enable CPU/System Fan Stop Warning function. Option available: Enabled/Disabled. Default setting is Enabled.

SYS_FAN Smart fan 3pin/4pin Define 3pin or 4 pin for System Smart Fan. Option available: 3pin/4pin. Default setting is 3pin.

System SMART FAN Function Enable System Smart Fan function. Option available: Enabled/Disabled. Default setting is Enabled.

SYS FAN Type Select system fan type. Option available: 3 Pin/4 Pin. Default setting is 3 Pin.

CPU Temperature Displays current CPU temperature.

CPU/System Fan Speed (RPM) Displays current CPU and system fan speed.

2-2-5 H/W MonitorPress Enter to view the Hardware Monitor screen which displays a real-time record of the CPU/system tem-perature, and fan speed, Items on this window are non-configurable.

BIOS Setup - 40 -

2-3 Chipset Menu

Restore AC Power Loss This option provides user to set the mode of operation if an AC / power loss occurs. Power On: System power state when AC cord is re-plugged. Power Off: Do not power on system when AC power is back. Last State: Set system to the last sate when AC power is removed. Options available: Power On/Power Off/Last State. Default setting is Power Off.

Azalia Controller Enable/Disable onboard audio controller. Options available: HD Audio/Disabled. Default setting is HD Audio.

Onboard LAN Enable/Disable onboard LAN controller. Options available: Enabled/Disabled. Default setting is Enabled.

LAN PXE ROM Enable/Disable Boot Option for PXE device with option ROM. Options available: Enabled/Disabled. Default setting is Disabled.

LAN MAC Address Display the information of LAN1 MAC address.

Erp Support Enable/Disable Erp support function. Options available: Enabled/Disabled. Default setting is Enabled.

- 41 - BIOS Setup

2-4 Boot MenuThe Boot menu allows you to set the drive priority during system boot-up. BIOS setup will display an error message if the drive(s) specified is not bootable.

BootConfiguration Support Prompt Timeout

Number of seconds to wait for setup activation key. Press <+> or <-> keys to incresae/decrease desired value.

Bootup NumLock State Allows you to select power-on state for NumLock function. Options available: On/Off. Default setting is On.

Quiet Boot This BIOS feature determines if the BIOS should hide the normal POST message with the motherboard

or system manufacturer's full-screen. When it is enabled, the BIOS will display the full-screen logo during the boot-up sequence, hiding normal

POST message. When it is disabled, the BIOS will display the normal POST messages, instead of the full-screen logo, Options available: Enabled/Disabled. Default setting is Disabled.

Fast Boot When it is enabled, the BIOS skip certain checks during POST. Options available: Enabled/Disabled. Default setting is Disabled.

BIOS Setup - 42 -

CSM16 Module Version Displays the CSM16 Module Version number.

GateA20 Active This BIOS feature is used to determine the method by which Gate A20 is controlled. Options available: Upon Request/Always. Default setting is Upon Request.

Option ROM Messages Set display mode for option ROM. Options available: Force BIOS/Keep Current. Default setting is Force BIOS.

Interrupt 19 Capture Interrupt 19 is the software interrupt that handles the boot disk function. When enabled, this BIOS

feature allows the ROM BIOS of those host adaptors to "capture" Interrupt 19 during the boot process so that drives attached to these adaptors can function as bootable disks. Options available: Enabled/Disabled. Default setting is Enabled.

CSM Support Enable/Disable Compatibility Support Module (CSM) suuport function. Options available: Enabled/Disabled. Default setting is Enabled.

Boot Option Priorities Boot Option #1/2/3

Press Enter to configure the boot priority. Hard Drive BBS Priorities

Press Enter to configure the boot priority.

- 43 - BIOS Setup

There are two types of passwords that you can set:• Adminstrator Password Entering this password will allow the user to access and change all settings in the Setup Utility. • User Password Entering this password will restrict a user’s access to the Setup menus. To enable or disable this field, a Administrator Password must first be set. A user can only access and modify the System Time, System Date, and Set User Password fields.

AdministratorPassword Press Enter to configure the Administrator password.

User Password Press Enter to configure the user password.

2-5 Security MenuThe Security menu allows you to safeguard and protect the system from unauthorized use by setting up ac-cess passwords.

BIOS Setup - 44 -

2-6 Save & Exit MenuThe Exit menu displays the various options to quit from the BIOS setup. Highlight any of the exit options then press Enter.

Save Changes and Exit Saves changes made and close the BIOS setup and exit system setup. Options available: Yes/No.

Discard Changes and Exit Discards changes made and close the BIOS setup and exit system setup . Options available: Yes/No.

Save Changes and Reset Active this option to reset system after saving the changes. Options available: Yes/No.

Discard Changes and Reset Active this option to reset system after without saving any changes. Options available: Yes/No.

Save Changes Active this option to save all the changes.

Discard Changes Discards changes made and close the BIOS setup.

Save as User Defaults Press <Enter> on this item and then press the <Y> key to load user default settings. Options available: Yes/No.

- 45 - BIOS Setup

Restore as User Defaults Press <Enter> on this item and then press the <Y> key to restore user default settings. Options available: Yes/No.

Boot Override Press Enter to configure the device as the boot-up drive.

UEFI: Built-in in EFI Shell Press <Enter> on this item to Launch EFI Shell from filesystem device.

M5NM1I · 2019. 3. 29. · USB 2.0 Port The USB port supports the USB 2.0 specification. Use this...

Documents

Transcript of M5NM1I · 2019. 3. 29. · USB 2.0 Port The USB port supports the USB 2.0 specification. Use this...