m Fl 67449109
Transcript of m Fl 67449109
-
7/25/2019 m Fl 67449109
1/41
Printed in KoreaP/NO : MFL67449109 (1207-REV00)
CHASSIS : LA2AF
MODEL : 32LT670H 32LT670H-UACAUTIONBEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
LCD TV
SERVICE MANUAL
North/Latin America http://aic.lgservice.com
Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com
Internal Use Only
-
7/25/2019 m Fl 67449109
2/41
- 2 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
CONTENTS
CONTENTS .............................................................................................. 2
PRODUCT SAFETY ................................................................................. 3
SPECIFICATION ....................................................................................... 4
ADJUSTMENT INSTRUCTION ................................................................ 6
TROUBLESHOOTING .............................................................................16
BLOCK DIAGRAM.................................................................................. 22
EXPLODED VIEW .................................................................................. 23
SCHEMATIC CIRCUIT DIAGRAM ..............................................................
-
7/25/2019 m Fl 67449109
3/41
- 3 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1 W), keep the resistor 10 mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Before returning the receiver to the customer,
always perform an AC leakage current checkon the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1 Mand 5.2 M.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check(See below Figure)Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5 mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
IMPORTANT SAFETY NOTICE
SAFETY PRECAUTIONS
-
7/25/2019 m Fl 67449109
4/41
- 4 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
SPECIFICATIONNOTE : Specifications and others are subject to change without notice for improvement.
1. Application rangeThis spec sheet is applied Commercial LCD TV with LA2AE/F
chassis
2. Test conditionEach part is tested as below without special notice.
1) Temperature : 25 C 5 C (77 F 9 F), CST : 40 C5 C
2) Relative Humidity: 65 % 10 %
3) Power Voltage
: Standard input voltage (AC 110-240 V~, 50/60 Hz)
* Standard Voltage of each products is marked by models.
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
5) The receiver must be operated for about 5 minutes prior to
the adjustment.
3. Test method1) Performance: LGE TV test method followed
2) Demanded other specification
- Safety : UL, CSA, IEC specification
- EMC: FCC, ICES, IEC specification
4. General Specification
No Item Specifcation Remark
1 Receiving System 1) ATSC / NTSC-M, 64 & 256 QAM
2 Available Channel 1) VHF : 02~13
2) UHF : 14~69
3) DTV : 02-69
4) CATV : 01~135
5) CADTV : 01~135
3 Input Voltage 1) AC 100 ~ 240V 50/60Hz Mark : 110V, 60Hz (N.America)4 Market NORTH AMERICA
5 Screen Size 32 inch Wide (1366 X 768) HD +60Hz 32LT670H-UA
6 Aspect Ratio 16:9
7 Tuning System FS
8 Module T320XVN01.1 LGD 32LT670H-UA
9 Operating
Environment
1) Temp : 0 ~ 40 deg
2) Humidity : ~ 80 %
10 Storage
Environment
1) Temp : -20 ~ 60 deg
2) Humidity : ~ 85 %
-
7/25/2019 m Fl 67449109
5/41
- 5 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
5. RGB (PC)
No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed DDC
1 640*350 31.468 70.09 25.17 EGA
2 720*400 31.469 70.08 28.32 DOS O
3 640*480 31.469 59.94 25.17 VESA(VGA) O
4 800*600 37.879 60.31 40.00 VESA(SVGA) O
5 1024*768 48.363 60.00 65.00 VESA(XGA) O
6 1280*768 47.776 59.870 79.5 CVT(WXGA)
7 1360*768 47.712 60.015 85.50 VESA (WXGA)
6. HDMI Input
No. Resolution H-freq(kHz) V-freq.(kHz) Pixel clock(MHz) Proposed
PC DDC
1 640*350 31.468 70.09 25.17 EGA
2 720*400 31.469 70.08 28.32 DOS O
3 640*480 31.469 59.94 25.17 VESA(VGA) O
4 800*600 37.879 60.31 40.00 VESA(SVGA) O
5 1024*768 48.363 60.00 65.00 VESA(XGA) O
6 1280*768 47.776 59.870 79.5 CVT(WXGA)
7 1360*768 47.712 60.015 85.50 VESA (WXGA) O
DTV
1 720*480 31.47 60 27.027 SDTV 480P
2 720*480 31.47 59.94 27.00 SDTV 480P
3 1280*720 45.00 60.00 74.25 HDTV 720P
4 1280*720 44.96 59.94 74.176 HDTV 720P
5 1920*1080 33.75 60.00 74.25 HDTV 1080I
6 1920*1080 33.72 59.94 74.176 HDTV 1080I
7 1920*1080 67.500 60 148.50 HDTV 1080P
8 1920*1080 67.432 59.939 148.352 HDTV 1080P
9 1920*1080 27.000 24.000 74.25 HDTV 1080P
10 1920*1080 26.97 23.976 74.176 HDTV 1080P
11 1920*1080 33.75 30.000 74.25 HDTV 1080P
12 1920*1080 33.71 29.97 74.176 HDTV 1080P
-
7/25/2019 m Fl 67449109
6/41
- 6 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
ADJUSTMENT INSTRUCTION
1. Application RangeThis spec. sheet applies to LA2E/F Chassis applied LCD TV
all models manufactured in TV factory
2. Specification(1) Because this is not a hot chassis, it is not necessary touse an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
25 5 C of temperature and 6510% of relative humidity if
there is no specific designation.
(4) The input voltage of the receiver must keep 100~240V,
50/60Hz.
(5) At first Worker must turn on the SET by using Power Only
key.
(6) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15 C
In case of keeping module is in the circumstance of 0C, itshould be placed in the circumstance of above 15C for 2
hours
In case of keeping module is in the circumstance of below
-20C, it should be placed in the circumstance of above
15C for 3 hours.
[Caution]
When still image is displayed for a period of 20 minutes or
longer (especially where W/B scale is strong.
Digital pattern 13ch and/or Cross hatch pattern 09ch), there
can some afterimage in the black level area
3. Adjustment items3.1 Board Level Adjustment
(1) Adjust RGB (ADC)
(2) EDID/DDC download
Above adjustment items can be also performed in Final
Assembly if needed. Both Board-level and Final assembly
adjustment items can be check using In-Start Menu 1.
ADJUST CHECK.
RGB-PC Adjust will be calculated by 480i adjust value.
3.2. Final assembly adjustment(1) White Balance adjustment
(2) RS-232C functionality check
(3) Factory Option setting per destination
(4) Shipment mode setting (In-Stop)
3.3. Etc(1) Shipment conditions
(2) Service Option Default
(3) USB Download (S/W Update, Option and Service only)
(4) ISP Download (Optional)
4. Board Level Adjustment4.1. ADC Adjustment
4.1.1. Overview ADC adjustment is needed to find the optimum black level
and gain in Analog-to-Digital device and to compensate RGB
deviation.
4.1.2. Equipment & Condition(1) Protocol: RS-232C
(2) Inner Pattern
- Resolution : 1080p (Inner Pattern)
- Resolution : 1024*768 RGB (Inner Pattern)
- Pattern : Horizontal 100% Color Bar Pattern
- Pattern level : 0.70.1 Vp-p
4.1.3. Adjustment4.1.3.1. Adjustment method
- Using RS-232, adjust items listed in 3.1 in the other shown
in 4.1.3.3
4.1.3.2. Adj. protocol
Ref.) ADC Adj. RS232C Protocol_Ver1.0
4.1.3.3. Adj. order
aa 00 00 [Enter ADC adj. mode]
xb 00 40 [Change input source to Component1(1080i)]
ad 00 10 [Adjust 480i Comp1]
xb 00 60 [Change input source to RGB(1024*768)]
ad 00 10 [Adjust 1024*768 RGB]
ad 00 90 End adj.
Protocol Command Set ACK
Enter adj. mode aa 00 00 a 00 OK00x
Source change xb 00 40
xb 00 40
b 00 OK40x (Adjust 1080i Comp1 )
b 00 OK60x (Adjust 1024*768 RGB)
Begin adj. ad 00 10
Return adj. result OKx (Case of Success)
NGx (Case of Fail)
Read adj. data (main)
ad 00 20
(sub )
ad 00 21
(main)
000000000000000000000000007c007b006dx
(Sub)
000000070000000000000000007c00830077xConfrm adj. ad 00 99 NG 03 00x (Fail)
NG 03 01x (Fail)
NG 03 02x (Fail)
OK 03 03x (Success)
End adj. aa 00 90 a 00 OK90x
-
7/25/2019 m Fl 67449109
7/41
- 7 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
5. Manual Adjustment5.1. ADC Adjustment
5.1.1. Overview ADC adjustment is needed to find the optimum black level
and gain in Analog-to-Digital device and to compensate RGB
deviation
5.1.2. Equipment & Condition(1) Adjust Remocon
(2) 801GF(802B, 802F, 802R) o r MSPG925FA Pattern
Generator
- Resolution : 480i Comp1 (MSPG-925 FA: model -209,
pattern-65)
- Resolution : 1024*768 RGB (Inner Pattern)
- Pattern : Horizontal 100% Color Bar Pattern
- Pattern level: 0.70.1 Vp-p
- Image
- or Inner pattern
(3) Must use standard cable
5.1.3. Adjust method5.1.3.1. ADC RGB
(1) Press the In-start Key on the ADJ remote after at least 1
min of signal reception. Then, select ADC Calibration. And
Press OK Button on the menu Start. The adjustment will
start automatically.
(2) If ADC RGB is successful, ADC RGB Success isdisplayed and ADC RGB is completed.
If ADC calibration is failure, ADC RGB Fail is displayed.
(3) If ADC calibration is failure, after rechecking ADC pattern
or condition, retry calibration
5.2. EDID/DDC Download(EDID PCM)
5.2.1. Overview- It is a VESA regulation. A PC or a MNT will display an
optimal resolution through information sharing without any
necessity of user input. It is a realization of Plug and Play.
5.2.2. Equipment(1) Adjust remocon.
(2) Since embedded EDID data is used, EDID download JIG,HDMI cable and D-sub cable are not need
5.2.3. Download method(1) Press Adj. key on the Adj. R/C.
(2) Select EDID D/L menu.
(3) By pressing Enter key, EDID download will begin
(4) If Download is successful, OK is display, but If Download is
failure, NG is displayed.
(5) If Download is failure, Re-try downloads.
[Caution] : When EDID Download, must remove RGB/HDMI
Cable.
5.2.4. EDID DATA5.2.4.1. North America
(1) FHD Model - 8Bit
HDMI 1-FHD-10BIT (C/S : 989B)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 2620 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 0130 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 3050 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3960 | 3F 1F 52 10 00 0A 20 20 20 20 20 20 00 00 00 FC70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 98
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-------------------------------------------------------------------------------
0 | 02 03 1C F1 47 90 22 20 05 04 03 02 23 09 57 0710 | 67 03 0C 00 10 00 B8 2D E3 05 03 01 02 3A 80 1820 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 0050 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 8460 | 63 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | 40 84 63 00 00 1A 00 00 00 00 00 00 00 00 00 9B
HDMI 2-FHD-10BIT (C/S : 988B)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 2620 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 0130 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 3050 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3960 | 3F 1F 52 10 00 0A 20 20 20 20 20 20 00 00 00 FC70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 98
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-------------------------------------------------------------------------------
02 03 1C F1 47 90 22 20 05 04 03 02 23 09 57 07
10 | 67 03 0C 00 20 00 B8 2D E3 05 03 01 02 3A 80 1820 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E
40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 0050 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 8460 | 63 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | 40 84 63 00 00 1A 00 00 00 00 00 00 00 00 00 8B
-
7/25/2019 m Fl 67449109
8/41
- 8 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
HDMI 3-FHD-10BIT (C/S : 987B)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
20 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 0130 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 3050 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3960 | 3F 1F 52 10 00 0A 20 20 20 20 20 20 00 00 00 FC70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 98
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-------------------------------------------------------------------------------
0 | 02 03 1C F1 47 90 22 20 05 04 03 02 23 09 57 07
10 | 67 03 0C 00 30 00 B8 2D E3 05 03 01 02 3A 80 1820 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E
40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 0050 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 8460 | 63 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | 40 84 63 00 00 1A 00 00 00 00 00 00 00 00 00 7B
RGB-FHD (C/S : B1)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 68 A0 5A 78 0A EE 91 A3 54 4C 99 2620 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 0130 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30
50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 00 B1
(2) 8Bit
HDMI 1-FHD-8BIT (C/S : 98E2)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 2620 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 0130 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 3050 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3960 | 3F 1F 52 10 00 0A 20 20 20 20 20 20 00 00 00 FC70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 98
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-------------------------------------------------------------------------------
0 | 02 03 1C F1 47 90 22 20 05 04 03 02 23 09 57 07
10 | 67 03 0C 00 10 00 80 1E E3 05 03 01 02 3A 80 1820 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D
30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 0050 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 8460 | 63 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | 40 84 63 00 00 1A 00 00 00 00 00 00 00 00 00 E2
HDMI 2-FHD-8BIT (C/S : 98D2)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 2620 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 0130 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 3050 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3960 | 3F 1F 52 10 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 98
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
--------------------------------------------------------------------------------
0 | 02 03 1C F1 47 90 22 20 05 04 03 02 23 09 57 07
10 | 67 03 0C 00 20 00 80 1E E3 05 03 01 02 3A 80 1820 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 0050 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 8460 | 63 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | 40 84 63 00 00 1A 00 00 00 00 00 00 00 00 00 D2
HDMI 3-FHD-8BIT (C/S : 98C2)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-------------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 2620 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 0130 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 3050 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3960 | 3F 1F 52 10 00 0A 20 20 20 20 20 20 00 00 00 FC70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 98
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-------------------------------------------------------------------------------------
0 | 02 03 1C F1 47 90 22 20 05 04 03 02 23 09 57 0710 | 67 03 0C 00 30 00 80 1E E3 05 03 01 02 3A 80 1820 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 0050 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 8460 | 63 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 0070 | 40 84 63 00 00 1A 00 00 00 00 00 00 00 00 00 C2
-
7/25/2019 m Fl 67449109
9/41
- 9 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
RGB-FHD (C/S : B1)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 68 A0 5A 78 0A EE 91 A3 54 4C 99 26
20 | 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 0130 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 3050 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 00 B1
(3) HD Model
HDMI 1-HD (C/S : 1AE2)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
10 | 01 16 01 03 80 A0 5A 78 0A CF 74 A3 57 4C B0 2320 | 09 48 4C A1 08 00 81 C0 01 01 01 01 01 01 01 0130 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 7040 | 36 00 40 84 63 00 00 1E 01 1D 00 72 51 D0 1E 2050 | 6E 28 55 00 40 84 63 00 00 1E 00 00 00 FD 00 3960 | 3F 1F 3C 09 00 0A 20 20 20 20 20 20 00 00 00 FC70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 1A
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-------------------------------------------------------------------------------
0 | 02 03 1C F1 47 10 22 20 05 84 03 02 23 09 57 07
10 | 67 03 0C 00 10 00 80 1E E3 05 03 01 02 3A 80 1820 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E
40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 0050 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 8460 | 63 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | 40 84 63 00 00 1A 00 00 00 00 00 00 00 00 00 E2
HDMI 2-HD (C/S : 1AD2)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 80 A0 5A 78 0A CF 74 A3 57 4C B0 2320 | 09 48 4C A1 08 00 81 C0 01 01 01 01 01 01 01 0130 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 7040 | 36 00 40 84 63 00 00 1E 01 1D 00 72 51 D0 1E 2050 | 6E 28 55 00 40 84 63 00 00 1E 00 00 00 FD 00 3960 | 3F 1F 3C 09 00 0A 20 20 20 20 20 20 00 00 00 FC70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 1A
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
--------------------------------------------------------------------------------
0 | 02 03 1C F1 47 10 22 20 05 84 03 02 23 09 57 07
10 | 67 03 0C 00 20 00 80 1E E3 05 03 01 02 3A 80 1820 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D
30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 0050 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 8460 | 63 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | 40 84 63 00 00 1A 00 00 00 00 00 00 00 00 00 D2
HDMI 3-HD (C/S : 1AC2)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-------------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 80 A0 5A 78 0A CF 74 A3 57 4C B0 2320 | 09 48 4C A1 08 00 81 C0 01 01 01 01 01 01 01 0130 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 | 36 00 40 84 63 00 00 1E 01 1D 00 72 51 D0 1E 2050 | 6E 28 55 00 40 84 63 00 00 1E 00 00 00 FD 00 3960 | 3F 1F 3C 09 00 0A 20 20 20 20 20 20 00 00 00 FC70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 1A
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-------------------------------------------------------------------------------------
0 | 02 03 1C F1 47 10 22 20 05 84 03 02 23 09 57 0710 | 67 03 0C 00 30 00 80 1E E3 05 03 01 02 3A 80 1820 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 0050 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 8460 | 63 00 00 18 26 36 80 A0 70 38 1F 40 30 20 25 00
70 | 40 84 63 00 00 1A 00 00 00 00 00 00 00 00 00 C2
RGB-HD (C/S : 6E)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-------------------------------------------------------------------------------------
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 0110 | 01 16 01 03 68 A0 5A 78 0A CF 30 A3 57 4C B0 2320 | 09 50 4E A1 08 00 81 C0 01 01 01 01 01 00 01 0130 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 7040 | 36 00 40 84 63 00 00 1E 01 1D 00 72 51 D0 1E 2050 | 6E 28 55 00 40 84 63 00 00 1E 00 00 00 FD 00 3960 | 3F 1F 3C 09 00 0A 20 20 20 20 20 20 00 00 00 FC70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 00 6E
-
7/25/2019 m Fl 67449109
10/41
- 10 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
6. Final Assembly Adjustment6.1. White Balance Adjustment
6.1.1. Overview6.1.1.1. W/B adj. Objective & How-it-works
(1) Objective: To reduce each Panels W/B deviation
(2) How-it-works: When R/G/B gain in the OSD is at 192, itmeans the panel is at its Full Dynamic Range. In order to
prevent saturation of Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is lowered to find
the desired value.
(3) Adj. condition: normal temperature
- Surrounding Temperature: 255 C
- Warm-up time: About 5 Min
- Surrounding Humidity: 20% ~ 80%
Before White balance adjustment, Keep power on status,
dont power off
6.1.1.2. Adj. condition and cautionary items
(1) Lighting condition in surrounding area surrounding lighting
should be lower 10 lux. Try to isolate adj. area into dark
surrounding.(2) Probe location: Color Analyzer (CA-210) probe should be
within 10cm and perpendicular of the module surface
(80~ 100)
(3) Aging time
- After Aging Start, Keep the Power ON status during 5
Minutes.
- In case of LCD, Back-light on should be checked using no
signal or Full-white pattern.
6.1.2. Equipment(1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12 / LED:
CH14)
(2) Adj. Computer(During auto adj., RS-232C protocol is
needed)
(3) Adjust Remocon
(4) Video Signal Generator MSPG-925F 720p/204-Gray
(Model:217, Pattern:49)
Only when internal pattern is not available
Color Analyzer Matrix should be calibrated using
CS-1000
6.1.3. Equipment connection MAP
6.1.4. Adjustment Command (Protocol)(1) RS-232C Command used during auto-adj
RS-232C COMMANDExplanation
CMD DATA ID
Wb 00 00 Begin White Balance adj.
Wb 00 ff End White Balance adj.
(internal pattern disappears )
Ex) wb 00 00 -> Begin white balance auto-adj.
wb 00 10 -> Gain adj.
ja 00 ff -> Adj. data
jb 00 c0
...
...
wb 00 1f -> Gain adj. complete
*(wb 00 20(start), wb 00 2f(end)) -> Off-set adj.
wb 00 ff ->End white balance auto adj
(2) Adjustment Map
Applied Model : 26/32/37/42LT670H-UA
Adj. item
Command(lower case ASCII)
Data Range(Hex.)
Default(Decimal)
CMD1 CMD2 MIN MAX 172
Cool R Gain j g 00 C0 172
G Gain j h 00 C0 192
B Gain j i 00 C0 64
R Cut 64
G Cut 64
B Cut 192
Medium R Gain j a 00 C0 192
G Gain j b 00 C0 192
B Gain j c 00 C0 64
R Cut 64
G Cut 64
B Cut 192
Warm R Gain j d 00 C0 192
G Gain j e 00 C0 172
B Gain j f 00 C0 64
R Cut 64
G Cut 64
Color Analyzer
Computer
Pattern Generator
Signal Source
Probe
RS-232C
RS-232C
RS-232C
If TV internal pattern is used, not needed
-
7/25/2019 m Fl 67449109
11/41
- 11 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
6.1.5. Adjustment method6.1.5.1 Auto adj. method
(1) Set TV in adj. mode using POWER ONLY (P-ONLY) key
(2) Zero calibrate probe then place it on the center of the
Display
(3) Connect Cable(RS-232C)
(4) Select mode in adj. Program and begin adj.(5) When adj. is completed (OK Sing), check adj. status of pre
mode (Cool, Medium, Warm)
(6) Remove probe and RS-232C cable to complete adj.
W/B Adj. must begin as start command wb 00 00 , and
finish as end command wb 00 ff, and Adj. offset if need
6.1.5.2. Manual adj. method
(1) Set TV in Adj. mode using POWER ON
(2) Zero Calibrate the probe of Color Analyzer, then place it on
the center of LCD module within 10cm of the surface..
(3) Press ADJ key -> EZ adjust using adj. R/C -> 6. White-
Balance then press the cursor to the right (KEY).
(When KEY() is pressed 204 Gray(80IRE) internal
pattern will be displayed)(4) One of R Gain / G Gain / B Gain should be fixed at 192,
and the rest will be lowered to meet the desired value.
(5) Adj. is performed in COOL, MEDIUM, WARM 3 modes of
color temperature.
If internal pattern is not available, use RF input. In EZ Adj.
menu 6.White Balance, you can select one of 2 Test-pattern:
ON, OFF. Default is inner(ON). By selecting OFF, you can
adjust using RF signal in 204 Gray pattern.
Adj. condition and cautionary items
(1) Lighting condition in surrounding area
Surrounding lighting should be lower 10 lux. Try to isolate
adj. area into dark surrounding.
(2) Probe location : Color Analyzer (CA-210) probe should be
within 10cm and perpendicular of the module surface (80~100)
(3) Aging time
- After Aging Start, Keep the Power ON status during 5
Minutes.
- In case of LCD, Back-light on should be checked using no
signal or Full-white pattern.
6.1.6. Reference (White Balance Adj. coordinate and
color temperature) Luminance: 204 Gray, 80IRE
** LGD Module (over 26inch)
Standard color coordinat e and t emperatur e using
CA-210(CH 14)
ModeCoordinate
Temp uv RemarkX Y
Cool 0.2690.002 0.2730.002 13,000K 0.0000 26/32/37/
42LT670H-UAMedium 0.2850.002 0.2930.002 9,300K 0.0000
Warm 0.3130.002 0.3290.002 6,500K 0.0000
Standard color coordinat e and t emperatur e using
CA-210(CH 14)
ModeCoordinate
Temp uvX Y
Cool 0.2690.002 0.2730.002 13,000K 0.0000
Medium 0.2850.002 0.2930.002 9,300K 0.0000
Warm 0.3130.002 0.3290.002 6,500K 0.0000
Standard color coordinat e and t emperatur e using
CA-210(CH 14) by aging time
(1) Edge LED models (applied only LGD Module) in LGERS
GP3Aging time
(Min)
Cool Medium Warm
X Y X Y X Y
269 273 285 293 313 329
1 0-2 279 288 295 308 319 338
2 3-5 278 286 294 306 318 336
3 6-9 277 285 293 305 317 335
4 10-19 276 283 292 303 316 333
5 20-35 274 280 290 300 314 330
6 36-49 272 277 288 297 312 327
7 50-79 271 275 287 295 311 325
8 80-149 270 274 286 294 310 324
9 Over 150 269 273 285 293 309 323
(2) Edge LED models (applied only LGD Module) in LGEKR
(GUMI) (wintertime)
GP3Aging time
(Min)
Cool Medium Warm
X Y X Y X Y
269 273 285 293 313 329
1 0-2 281 293 297 313 321 3432 3-5 280 290 296 310 320 340
3 6-9 279 289 295 309 319 339
4 10-19 277 286 293 306 317 333
5 20-35 275 282 291 302 315 332
6 36-49 273 278 289 298 313 328
7 50-79 271 276 287 296 311 326
8 80-149 270 274 286 294 310 324
9 Over 150 269 273 285 293 309 323
-
7/25/2019 m Fl 67449109
12/41
- 12 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
6.2. Option selection per country
6.2.1. Overview(1) Option selection is only done for models in Non-USA North
America due to rating
(2) Applied model: LA2AE/F Chassis is applied in USA
6.2.2. Method(1) Press ADJ key on the Adj. R/C, and then select Country
Group Menu
(2) Depending on destination, select KR or US, then on the
lower Country option, select US, CA, MX.
Selection is done using +, - KEY
6.2.3. Tool Option inspection Press Adj. key on the Adj. R/C, then select Tool option.
Model Tool 1 Too l 2 Tool 3 Tool 4 Tool 5 COM-
MERCIAL
OPTION
37LT670H-UA 16389 2338 9489 17324 36 1618 LGD
42LT670H-UA 16390 2338 9489 21420 36 1618 LGD
32LT670H-UA 16388 2321 9489 17324 36 1618 LGD
26LT670H-UA 16387 290 9489 17324 36 1618 LGD
6.2.4. Ship-out mode check (In-stop) After final inspection, press In-Stop key of the Adj. R/C and
check that the unit goes to Stand-by mode
7. GND and HI-POT Test7.1. GND & HI-POT auto-check preparation
(1) Check the POWER CABLE and SIGNAL CABE insertion
condition
7.2. GND & HI-POT auto-check(1) Pallet moves in the station. (POWER CORD / AV CORD is
tightly inserted)
(2) Connect the AV JACK Tester.
(3) Controller (GWS103-4) on.
(4) GND Test (Auto)
- If Test is failed, Buzzer operates.
- If Test is passed, execute next process (Hi-pot test).
(Remove A/V CORD from A/V JACK BOX)
(5) HI-POT test (Auto)
- If Test is failed, Buzzer operates.
- If Test is passed, GOOD Lamp on and move to next process
automatically.
7.3. Checkpoint(1) Test voltage
- GND: 1.5KV/min at 100mA
- SIGNAL: 3KV/min at 100mA
(2) TEST time: 1 second
(3) TEST POINT
- GND Test = POWER CORD GND and SIGNAL CABLE GND.
- Hi-pot Test = POWER CORD GND and LIVE & NEUTRAL.
(4) LEAKAGE CURRENT: At 0.5mArms
8. AUDIO output check8.1. Audio input condition
(1) RF input: Mono, 1KHz sine wave signal, 100% Modulation
(2) CVBS, Component: 1KHz sine wave signal (0.4Vrms)
(3) RGB PC: 1KHz sine wave signal (0.7Vrms)
8.2. Specification
Measurement condition:(1) RF input: Mono, 1KHz sine wave signal, 100% Modulation
(2) CVBS, Component: 1KHz sine wave signal 0.4Vrms
(3) RGB PC: 1KHz sine wave signal 0.7Vrms
-
7/25/2019 m Fl 67449109
13/41
- 13 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
9. USB S/W Download
(optional, Service only)(1) Put the USB Stick to the USB socket
(2) Automatically detecting update file in USB Stick
- If your downloaded program version in USB Stick is lower
than that of TV set, it didnt work. Otherwise USB data is
automatically detected.
(3) Show the message Copying files from memory
(5) Updating Completed, The TV will restart automatically
(6) If your TV is turned on, check your updated version and
Tool option.
* If downloading version is more high than your TV have, TV
can lost all channel data. In this case, you have to channel
recover. If all channel data is cleared, you didnt have a DTV/
ATV test on production line.
* After downloading, TOOL OPTION setting is needed again.
(1) Push "IN-START" key in service remote controller.
(2) Select "Tool Option 1" and Push OK button.
(3) Punch in the number. (Each model has their number.)
10. Conditions ST_BY Consumption
Power- Have to turn-off ST_BY Light
- USA 110V / 60Hz, KOREA 220V / 60Hz
(Menu -> Option -> Power Indicator -> ST_BY Light : OFF)
11. Test factor for commercial model11.1. RJP TEST
{Picture1}11.1.1. Overview
Jig(Commercial Check JIG)
Power only mode
11.1.2. Test sequence(1) Connect the adapter to the Commercial check Jig for
supplying voltage
(2) Turn on the TV and fix the channel to 96-1
(3) Adjust each switch on left side to; adapter and 5V
(4) Turn on JIG pin No. 5. as picture 1
(5) Press the P-ONLY key for Encryption channel check
(6) Press the EXIT key
(7) Check to confirm the encryption channel
(8) Connect the LAN Cable(9) Check RJP TEST : OK message.
(4) Updating is staring.
-
7/25/2019 m Fl 67449109
14/41
- 14 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
12. External Speaker Out
(1) Connect external speaker to speaker out port with phone
jack on TV side as below
(2) Check the Max. speaker output is 1W or not. Sine wave
with 1KHz will be displayed
(3) Check Both of the signal in speaker.
(only Power -> Fived 1W Default)
-> Check the input signal(1KHZ, Sine wave) and the wave
of output by utilizing oscilloscope.
13. LAN Main board Check13.1. Overview
It is LNET RF modem & FTG card
13.2. Equipment
(1) b_LAN Checker: UTC-1000 (with Cable accessory)(2) Computer(for test result monitoring)
(3) Connection JIG
13.3. Equipment connection map & b_LAN
Check
Recommended Input Signal
: RF, 1kHz, Sine wave
-
7/25/2019 m Fl 67449109
15/41
- 15 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
13.4. Check
13.4.1. Setting Procedure13.4.1.1. Setting JIG
(1) Connect UTC-1000 Equipment to JIG device as a like left
picture
- Connection Line:
UTC-1000 TOP1Game port(RJ21) -> TV-LINK CFG (Phone Jack)
UTC-1000 TOP2JIG 11pin Connection
UTC-1000 RF1b_LAN RF IN
UTC-1000 LANPC LAN Port
13.4.1.2. Working procedure
(1) Connection
UTC-1000 LAN PC LAN Port
UTC-1000 TOP1 Game port(RJ21)
-> TV-LINK CFG (Phone Jack)
UTC-1000 RF1 b_LAN RF IN
(2) Power on JIG : Switch on front of the JIG
(3) Test Start
UTC-1000 TOP2 JIG 11pin Connection
(4) Checking b-LAN MAC AddressCheck whether it is same their address numbers or not
between B-LAN Label and on the pc address numbers.
Checking JIG contents
(1) Check whether displaying all Pass or not at the number
3.4.6.7.9 contents of UTC-1000 on the PC
(2) Check Version 6.0 of the 1. b_LAN Application version
(3) Check whether it is same their address numbers or not
between B-LAN Label and
(4) MAC Address on the pc.
14. Serial number downloadConnect Bar Code scan equipment and TV set by RS-232C
cable
(1) E2PROM Data Write
(2) E2PROM Data Read
-
7/25/2019 m Fl 67449109
16/41
- 16 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
TROUBLESHOOTING
Power-Up Boot Fail Trouble Shooting guide
Check P401 AllVoltage Level (3.5V, 12V, 24V)
Y
N
Check Q409 output Voltage(12V)
Y
Check LVDS Cable
Y
Check LCD Module
Control board
Check power connector and
RL_ON signal OK ?
NReplace Power Board
Check Q409 application circuit
Or replace Q409
N
Replace CableN
No OSD Trouble Shooting guide
Check P401 AllVoltage Level (3.5V, 12V, 24V)
Y
N
Check IC5002 RESET andUPDATE pin
Y
Check X5000 Clock
32.768MHz
Y
Check IC5002 IIC
Communication status
Y
Check IR input state of IC5002
57pin
Y
Re-download PTC Micom
Check power connector and
RL_ON signal OK ?
NReplace Power Board
Check switch SW5000, SW5001
N
Check X5000 application circuit
or Replace X5000
Check IIC line or replace IC5002
Check IR board
N
N
N
-
7/25/2019 m Fl 67449109
17/41
- 17 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
Analog RF Video Trouble Shooting guide
Check RF cable & signal
Y
Check TU3001 Pin7
(Video output)
Y
Check tuner 5V power L3000
Y
Check tuner 3.3V power L3001
Y
Check tuner 1.8V power IC3000
2pin : 1.8V
Y
Check Mstar LVDS output
Replace Tuner.
N
Check IC5000
Replace L3001
Replace IC3000
N
N
N
Replace IC101N
Replace IC5000N
Y
-
7/25/2019 m Fl 67449109
18/41
- 18 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
Digital RF Trouble Shooting guide
Check RF cable & signal
Check tuner 5V power L3000
Y
Check IIC Signal
TU3001 Pin#3,4
Y
Check DIF Signal
TU3001 Pin#10,11
Y
Check X201
and application circuit
Check IC5000
Replace TU3001
Replace TU3001
N
N
N
Replace IC101
N
Replace IC5000
N
Y
Replace X201
-
7/25/2019 m Fl 67449109
19/41
- 19 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
Composite Video Trouble Shooting guide
Check input signal format.
Is it supported?
Y
Check AC cable for damage
For damage or open conductor
Y
Check JK1700
Can you see the normal waveform?
Y
Check the input of Mstar(IC101).
Measure waveform at C217 because its more easy to check.
Can you see the normal waveform?
Y
This board has big problem because Main chip (Mstar) have some troubles.
After checking thoroughly all path once again, You should decide to replace Mstar or not.
Replace JK1700N
HDMI Video Trouble Shooting guide
Check input signal format.
Is it supported?
Y
Check AC cable for damage
For damage or open conductor
Y
Check JK800/JK801/JK802
Can you see the normal waveform?
Y
Check HDCP key NVRAM(IC103)
Power & I2C signal
Y
Check the input of Mstar(IC101).
Measure waveform at R4024, R4025 because its more easy to check.
Can you see the normal waveform?
Y
This board has big problem because Main chip (Mstar) have some troubles.
After checking thoroughly all path once again, You should decide to replace Mstar or not.
Replace JK800, JK801, JK802N
Replace IC103N
-
7/25/2019 m Fl 67449109
20/41
- 20 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
RGB-PC Video Trouble Shooting guide
Check input signal format.
Is it supported?
Y
Check AC cable for damage
For damage or open conductor
Y
Check P900
Can you see the normal waveform?
Y
Check the input of Mstar(IC101).
Measure waveform at R4025, R4042 because its more easy to check.
Can you see the normal waveform?
Y
This board has big problem because Main chip (Mstar) have some troubles.
After checking thoroughly all path once again, You should decide to replace Mstar or not.
Replace P900N
Analog RF Audio Trouble Shooting guide
Check RF cable & signal
Check TU3001 Pin1
(SIF output)
Y
Check Audio AMP output
L503,L504,L505,L506
Y
Check IC501
Y
Check C250(SIF signal to IC101)
Replace Tuner
N
Replace L503,L504,L505,L506
Replace IC501
N
N
Replace IC101
Y
-
7/25/2019 m Fl 67449109
21/41
- 21 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
Composite / RGB-PC Audio in Trouble Shooting guide
HDMI Audio in Trouble Shooting guide
Check input signal format.
Is it supported?
Y
Check AC cable for damage
For damage or open conductor
Y
Check JK1700, P800
Can you see the normal waveform?
Y
Check the input of Mstar(IC101).
Measure waveform at C236, C237, C244, C245 because its more easy to check.
Can you see the normal waveform?
Y
This board has big problem because Main chip (Mstar) have some troubles.
After checking thoroughly all path once again, You should decide to replace Mstar or not.
Replace JK1700, P800N
Check Audio AMP output
L503,L504,L505,L506Replace L503,L504,L505,L506
N
Y
Check input signal format.
Is it supported?
Y
Check AC cable for damage
For damage or open conductor
Y
Check JK800, JK801, JK802Can you see the normal waveform?
Y
This board has big problem because Main chip (Mstar) have some troubles.
After checking thoroughly all path once again, You should decide to replace Mstar or not.
Replace JK800, JK801, JK802N
Check Audio AMP output
L503,L504,L505,L506Replace L503,L504,L505,L506
N
Y
-
7/25/2019 m Fl 67449109
22/41
- 22 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
BLOCK DIAGRAM
DDR2(2Gbit)
H5TQ2G63BFR-H9C
IC1201
NANDFlash(2Gbit)
HY27UF082G2B-TPCB
IC102
DigitalAMP
NTP7500L
IC1600
I2S
A_Data[0
:15],
DDR2(1Gbit)
H5TQ1G63DFR-H9C
IC1202
B_Data[0
:15],
Addr.[],ctrl,DQS,DM
PCM_A[
0
7]
IFN/P
SIF
TU_CVBS
X-tal
Reset/IF_AGC
SDA/SCL_5V
ResetSwitch
CS,RE,W
E
RX/TX
Micom
(MSP430F5419IPZR)
IC5002
24MHz
JACK
PACK
JACK
PACK
atREAR
atREAR
SCL,SDA_3.3V
RF
S7LR(LGE2111A-TE)
IC101
RS-2
32C
(S
VC)
S/WRes
et
EXT_OU
T
I2C(SCL/
SDA)
S_FLASH(8Mbit)
MX25L8006EM2I-12G
IC200
PowerAMP
TPA6011A4PWPRG4
IC1800
JK1801
JK1800
RJP_CTRL
JK5000
Pro:Idom
LGDT1001
IC1209
TS_CLK,VALID,SYNC,0~7
PM_TS_CLK,VALID,SYNC,0~7
TMMB
-H002F
B-LAN
TV-linkCFG
Gamecontrol
TV-linkCFG
Gamecontrol
AudioL/R
PCA
udio
JK700
JK1700
AudioL/R
PCA
udio
JK700
JK1700
HDMI1
HDMI2
HDMI1
HDMI2
RGB
PC
AVUS
B
RGB/H/V
CVBS,L/R
SIDE_USB_DP/DM/+5V
JACK
PACK
JACK
PACK
atSide
atSide
HDM
I3
-
7/25/2019 m Fl 67449109
23/41
- 23 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.
Only for training and service purposes
EXPLODED VIEW
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
IMPORTANT SAFETY NOTICE
300
200
510 5
00
120
530 55
0
810
521
800
LV1
400
910
900
540
*Set+Stand
*StandBase+Body
A10
A7
A2
-
7/25/2019 m Fl 67449109
24/41
MBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
ND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
AL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
/PCM_IOWR
8pF
OPT
C106
/PCM_CD
/PCM_WE
22R111
5V_DET_HDMI_4
2 2 R 14 2
100pF50V
C112
AMP_MUTE
0 .1uFOPT
C108
AMP_SCL
INV_CTL
1KR
117
OPT
I2C_SDA
3 3 R1 46
PWM0
P
10KR132
SENSOR_SDA
RGB_DDC_SDA
DSUB_DET
PANEL_CTL
KEY1
FE_TS_VAL_E
PCM_RST
1KR
165
NAND01GW3B2CN6E
EAN60762401
IC102
NAND_FLASH_1G_NUMONYX
26NC_17
27NC_18
28NC_19
29I /O 0
30I /O 1
31I /O 2
32I /O 3
33NC_20
34NC_21
35NC_22
36VSS_2
37VDD_2
38NC_23
39NC_24
40NC_25
41I /O 4
42I /O 5
43I /O 6
44I /O 7
45NC_26
46NC_27
47NC_28
48NC_29
17AL
3NC_3
6NC_6
16CL
15NC_10
14NC_9
13VSS_1
12VDD_1
11NC_8
10NC_7
9E
8R
7RB
4NC_4
5NC_5
25NC_16
24NC_15
23NC_14
2NC_2
22NC_13
21NC_12
1NC_1
20NC_11
19WP
18W
1K
R153
I2C_SDA
SCART1_MUTE
1K
R141
AV_CVBS_DET
CI_TS_DAH27U1G8F2BTR-BC
EAN35669102
IC102-*1
NAND_FLASH_1G_HYNIX
26NC_17
27NC_18
28NC_19
29I/O0
30I/O1
31I/O2
32I/O3
33NC_20
34NC_21
35NC_22
36VSS_2
37VCC_2
38NC_23
39NC_24
40NC_25
41I/O4
42I/O5
43I/O6
44I/O7
45NC_26
46NC_27
47NC_28
48NC_29
17ALE
3NC_3
6NC_6
16CLE
15NC_10
14NC_9
13VSS_1
12VCC_1
11NC_8
10NC_7
9CE
8RE
7R/B
4NC_4
5NC_5
25NC_16
24NC_15
23NC_14
2NC_2
22NC_13
21NC_12
1NC_1
20NC_11
19WP
18WE
/PF_CE1
I2C_SDA
3 3 R1 51
56
R148
1KR
115
OPT
TC58NVG0S3ETA0BBBH
EAN61508001IC102-*3
NAND_FLASH_1G_TOSHIBA
26NC_17
27NC_18
28NC_19
29I/O1
30I/O2
31I/O3
32I/O4
33NC_20
34NC_21
35NC_22
36VSS_2
37VCC_2
38NC_23
39NC_24
40NC_25
41I/O5
42I/O6
43I/O7
44I/O8
45NC_26
46NC_27
47NC_28
48NC_29
17ALE
3NC_3
6NC_6
16CLE
15NC_10
14NC_9
13VSS_1
12VCC_1
11NC_8
10NC_7
9CE
8RE
7RY/BY
4NC_4
5NC_5
25NC_16
24NC_15
23NC_14
2NC_2
22NC_13
21NC_12
1NC_1
20NC_11
19WP
18WE
/FLASH_WP
22AR103
22 R154
OPT
PM_TXD
RGB_DDC_SCL
1K
R140
1K
R121
OPT
+3.3V_Normal
USB1_CTL
I2C_SCL
/PCM_IORD
EXT_SPK_DET
CI_TS_CLK
1K
R107
PCM_A[0-7]
POWER_DET
/CI_CD2
/PCM_CE
AMP_SDA
FE_TS_DA
2.2
K
R145
10K
R104
OPT
PCM_A[0-14]
PWM1
USB1_OCD
PWM_DIM
22R166
22R137
1KR
152
OPT
1K
R118
/PF_OE
3 3 R1 47
+3.3V_Normal
ERROR_OUT
/PF_OE
SC1/COMP1_DET
PWM0
1K
OPT
R105
MODEL_OPT_1
0 .1uFC101
2 .2uFC111
PWM1
/PF_CE0
PF_ALE
PWM0
/PF_CE0
/PF_WE
AUD_MASTER_CLK
+3.5V_ST
AMP_RESET
/SPI_CS
2 2 R122OPT
TUNER_RESET
2 2 R 10 1
SENSOR_SCL
100R157
1K
R116
22R169
2 2 R120
OPT
MODEL_OPT_2
22R139
22R112
+3.3V_Normal
+3.3V_Normal
SPI_SDO
4.7
KR143
TOUCH_KEY
/PCM_OE
2.2
K
R144
SENSOR_SCL
LED_B/LG_LOGO
PWM2
10KR133
2 2 R 16 3
PCM_5V_CTL
PCM_D[0-7]
1K
OPT
R108
/PF_CE1
PM_RXD
2 2 R110
AUD_SCK
/PCM_REG
2 2 R131
CI_TS_VAL
3.9
K
R109
PM_TXD
22R170
5V_DET_HDMI_2
/F_RB
SENSOR_SDA
22R136
2 2 R135
KEY2
/PCM_IRQA
S/T_SDA
10KR156
2 2 R134
K9F1G08U0D-SCB0
EAN61857001IC102-*2
NAND_FLASH_1G_SS
26NC_17
27NC_18
28NC_19
29I /O 0
30I /O 1
31I /O 2
32I /O 3
33NC_20
34NC_21
35NC_22
36VSS_2
37VCC_2
38NC_23
39NC_24
40NC_25
41I /O 4
42I /O 5
43I /O 6
44I /O 7
45NC_26
46NC_27
47NC_28
48NC_29
17ALE
3NC_3
6NC_6
16CLE
15NC_10
14NC_9
13VSS_1
12VCC_1
11NC_8
10NC_7
9CE
8RE
7R/B
4NC_4
5NC_5
25NC_16
24NC_15
23NC_14
2NC_2
22NC_13
21NC_12
1NC_1
20NC_11
19WP
18WE
0.1uFC103
S/T_SCL
/CI_CD1
1K
R12422
AR102
2.7
K
R161
+3.3V_Normal
0 .1uFC109
8pF
OPT
C104
5V_DET_HDMI_1
CI_TS_SYNC
22R168
2 2 R130
FE_TS_CLK
/F_RB
/PF_WP
22
AR101
PM_RXD
SPI_SDI
/PF_WE
0.1uFC105
LED_R/BUZZ
MODEL_OPT_0
I2C_SCL
+3.3V_Normal
10uFC102
4.7
KR149
TOUCH_KEY
RL_ON
1K
R106
/PCM_WAIT
AUD_MASTER_CLK_0
I2C_SCL
POWER_ON/O
+5V_Normal
A_DIM
1KR
123
OPT
2.7
K
R160
KRC103S
OPT
Q101
E
B
C
PF_ALE
SPI_SCK
PWM2
22AR104
FE_TS_SYNC
22R167
22R138
LED_R/BUZZ
3.3
K
R102
2 2 R 16 4
AT24C256C-SSHL-TIC104
3A2
2A1
4GND
1A0
5SDA
6SCL
7WP
8VCC
10KR171
OPT
PM_MODEL_O
PM_MODEL_OPT_0
+3.5V_ST
PM_MODEL_OPT_1
100R178OPT
100R179 OPT
OL
LGE2112-T8IC101
S7LR_DIVX_MS10
PCMDATA[0]/GPIO126W21
PCMDATA[1]/GPIO127AA18
PCMDATA[2]/GPIO128AB22
PCMDATA[3]/GPIO120AE20
PCMDATA[4]/GPIO119AA15
PCMDATA[5]/GPIO118AE21
PCMDATA[6]/GPIO117AB21
PCMDATA[7]/GPIO116Y15
PCMADR[0]/GPIO125W20
PCMADR[1]/GPIO124V20
PCMADR[2]/GPIO122W22
PCMADR[3]/GPIO121AB18
PCMADR[4]/GPIO99AA20
PCMADR[5]/GPIO101AA21
PCMADR[6]/GPIO102Y19
PCMADR[7]/GPIO103AB17
PCMADR[8]/GPIO108Y16
PCMADR[9]/GPIO110AB19
PCMADR[10]/GPIO114AB20
PCMADR[11]/GPIO112AA16
PCMADR[12]/GPIO104AA19
PCMADR[13]/GPIO107AC21
PCMADR[14]/GPIO106AA17
PCMREG_N/GPIO123Y20
PCMOE_N/GPIO113AB15
PCMWE_N/GPIO197AA22
PCMIORD_N/GPIO111AD22
PCMIOWR_N/GPIO109AD20
PCMCE_N/GPIO115AD21
PCMIRQA_N/GPIO105AC20
PCMCD_N/GPIO130Y18
PCMWAIT_N/GPIO100Y21
PCM_RESET/GPIO129Y22
PCM2_CE_N/GPIO131U21
PCM2_IRQA_N/GPIO132
V21
PCM2_CD_N/GPIO135R20
PCM2_WAIT_N/GPIO133T20
PCM2_RESET/GPIO134U22
UART1_TX/GPIO43D4
UART1_RX/GPIO44E4
UART2_TX/GPIO65N25
UART2_RX/GPIO64N24
UART3_TX/GPIO47B8
UART3_RX/GPIO48A8
I2C_SCKM2/DDCR_CK/GPIO72P23
I2C_SDAM2/DDCR_DA/GPIO71P24
DDCA_DA/UART0_TXD2
DDCA_CK/UART0_RXD1
PWM0/GPIO66P21
PWM1/GPIO67N23
PWM2/GPIO68P22
PWM3/GPIO69R21
PWM4/GPIO70P20
PWM_PM/GPIO199F6
SAR0/GPIO31H6
SAR1/GPIO32G5
SAR2/GPIO33G4
SAR3/GPIO34J5
SAR4/GPIO35J4
VSYNC_LIKE/GPIO145R23
SPI1_CK/GPIO201R24
SPI1_DI/GPIO202R25
SPI2_CK/GPIO203T21
SPI2_DI/GPIO204T22
NF_CE1Z/GPIO138AE18
NF_WPZ/GPIO198AC17
NF_CEZ/GPIO137AD18
NF_CLE/GPIO136AC18
NF_REZ/GPIO139AC19
NF_WEZ/GPIO140AD17
NF_ALE/GPIO141AE17
NF_RBZ/GPIO142AD19
GPIO_PM[0]/GPIO6H5
PM_UART_TX/GPIO_PM[1]/GPIO7K6
GPIO_PM[2]/GPIO8K5
GPIO_PM[3]/GPIO9J6
GPIO_PM[4]/GPIO10K4
PM_UART_RX/GPIO_PM[5]/GPIO11L6
PM_SPI_SCZ1/GPIO_PM[6]/GPIO12C2
GPIO_PM[7]/GPIO13L5
GPIO_PM[8]/GPIO14M6
GPIO_PM[9]/GPIO15M5
PM_SPI_SCZ2/GPIO_PM[10]/GPIO16C1
GPIO_PM[11]/GPIO17M4
PM_SPI_SCK/GPIO1A2
PM_SPI_CZ0/GPIO_PM[12]/GPIO0D3
PM_SPI_SDI/GPIO2B2
PM_SPI_SDO/GPIO3B1
TS0CLK/GPIO87Y14
TS0VALID/GPIO85AA10
TS0SYNC/GPIO86
Y12
TS0DATA_[0]/GPIO77Y13
TS0DATA_[1]/GPIO78Y11
TS0DATA_[2]/GPIO79AA12
TS0DATA_[3]/GPIO80AB12
TS0DATA_[4]/GPIO81AA14
TS0DATA_[5]/GPIO82AB14
TS0DATA_[6]/GPIO83AA13
TS0DATA_[7]/GPIO84AB11
TS1CLK/GPIO98AC15
TS1VALID/GPI96AD15
TS1SYNC/GPIO97AC16
TS1DATA_[0]/GPIO88AD16
TS1DATA_[1]/GPIO89AE15
TS1DATA_[2]/GPIO90AE14
TS1DATA_[3]/GPIO91AC13
TS1DATA_[4]/GPIO92AC14
TS1DATA_[5]/GPIO93AD12
TS1DATA_[6]/GPIO94AD13
TS1DATA_[7]/GPIO95AD14
LGE2112-T8IC101
S7LR_DIVX_MS10
GPIO36C7
GPIO37E6
GPIO38F5
GPIO39B6
GPIO40E5
GPIO41D5
GPIO42B7
GPIO45E7
GPIO46F7
GPIO49AB5
GPIO50AB3
GPIO51A9
GPIO52F4
I2C_SCKM0/GPIO53AB1
I2C_SDAM0/GPIO54N6
GPIO73AB2
GPIO74AC2
LVA0PAB25
LVA0NAB23
LVA1PAC25
LVA1NAB24
LVA2PAD25
LVA2NAC24
LVA3PAE23
LVA3NAC23
LVA4PAC22
LVA4NAD23
LVB0PV23
LVB0NU24
LVB1PV25
LVB1NV24
LVB2PW25
LVB2NW23
LVB3PAA23
LVB3NY24
LVB4PAA25
LVB4NAA24
LVACKPAE24
LVACKNAD24
LVBCKPY23
LVBCKNW24
GPIO196T25
GPIO193U23
GPIO194T24
GPIO195T23
MODEL_OPT_6
MODEL_OPT_7
L
S
GPIO36C7
GPIO37E6
GPIO38F5
GPIO39B6
GPIO40E5
GPIO41D5
GPIO42B7
GPIO45E7
GPIO46F7
GPIO49AB5
GPIO50AB3
GPIO51A9
GPIO52F4
I2C_SCAB1
I2C_SDN6
GPIO73AB2
GPIO74AC2
10KR176
PWM_LED
10KR177
PWM_BUZZ/IIC_LED10KR174
TOUCH_KEY
10KR175
TACT_KEY
SUB_AMP_M2 2 R 11 4
RJP_CTRL3
RJP_CTRL0
RJP_CTRL1
RJP_CTRL2
EXT12V_CTRL
EXT_PWR_DET
CI_TS_DATA[5]
CI_TS_DATA[1]
PCM_A[3]
PCM_A[12]
PCM_A[11]
CI_TS_DATA[3]
FE_TS_DATA[6]
CI_TS_DATA[4]
FE_TS_DATA[7]
PCM_A[0]
PCM_A[0]
PCM_A[4]
PCM_A[10]
PCM_A[9]
FE_TS_DATA[2]
PCM_A[6]
PCM_A[6]
FE_TS_DATA[0]
PCM_A[5]
PCM_A[1]
FE_TS_DATA[1]
PCM_A[8]
PCM_A[1]
PCM_A[7]
PCM_A[2]
PCM_D[5]
PCM_A[7]
PCM_A[4]
PCM_A[5]
PCM_D[4]
PCM_D[3]
PCM_A[3]
PCM_A[14]
PCM_D[2]
CI_TS_DATA[7]
PCM_A[2]
CI_TS_DATA[0]
FE_TS_DATA[3]
PCM_D[1]
PCM_D[0]
PCM_D[7]
PCM_A[13]
PCM_D[6]
FE_TS_DATA[4]
CI_TS_DATA[2]
CI_TS_DATA[6]
FE_TS_DATA[5]
201
FLASH/EEPROM/GPIO 1
from CI S
for SYSTEM/HDCPEEPROM&URSA3
for SERIAL FLASH
A0h
NAND FLASH MEMORY
NEED TO SWAP LVDS PO
EEPROM
Interna
(I2S_OUT_BCK,I2S_OUT_MCK,PAD_PWM1PAD_PWM0)
t o d e l e t e C I o r g a t e f o r
I2C
B 5 1 _ n o _ E J : 4 b 0 0 0 0 B o o t f r o m 8 0 5 1 w i t h S P I f l a s hSB 51_W O S : 4 b0001 Secu re B 51 w i thou t s c ram ble
SB 51_W S : 4 b0010 Secu re B 51 w i th sc ram bleM IPS_SPE _N O _E J : 4 b0100 B oo t f rom M IPS w i th SPI f l a sh
M IPS_SPI_E J_1 : 4 b0101 B oo t f rom M IPS w i th SPI f l a shM IPS_SPI_E J_2 : 4 b0110 B oo t f rom M IPS w i th SPI f l a shM IPS_W O S : 4 b1001 Secu re M IPS w i thou t s c ram bleM IPS_W S : 4 b1010 Sce ru r M IPS w i th SC R A M B L E
DIMMING
GP3_S7LR
PM MODEL OPTION
Boot from SPI CS1N(EXT_FLASH) 1b0Boot from SPI_CS0N(INT_FLASH) 1b1
applied on on
ht 2012 LG Electronics. Inc. All right reserved. training and service purposes LGE Inte
-
7/25/2019 m Fl 67449109
25/41
MBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
ND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
AL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
D1-_HDMI2
0 .1uFC252
+1.10V_VDDC
0.047uFC209
33R257
0.047uFC214
AMP_SDA
MODEL_OPT_0
IF_AGC_MAIN
510R4024
0.1
uF
C277
AVSS_PGA
2.2uFC237
SC1_SOG_IN
1K
DVB
_T2
R208
0 .1uFC4027
0.1
uF
C4036
0.1
uF
C4043
SCART1_Lout
SC1_CVBS_IN
AVDD_NODIE
100R202 OPT
0.1
uF
C265
0.047uFC208
0.1
uF
C4042
BLM18PG121SN1DL219
2 .2uFC243OPT
D0-_HDMI1
33R255
33R228
0.047uFC226
0.1
uF
C4038
DSUB_R+
0 .1uFC257
33R245
2 .2uFC245
DDC_SCL_1
D0+_HDMI4
33R239OPT
SC1_G+/COMP1_Y+
0.047uFC206
68R233
HPD4
0.047uFC230
1000pFC210
0.1
uF
C283
AVDD25_PGA
2.2uFC236
0.047uFC223
10K
R4026
0.1
uF
C4020
CK-_HDMI2
68R240 0.047uFC221
BLM18PG121SN1DL206
IF_N_MSTAR
BLM18PG121SN1DL209
AMP_SCL
D1+_HDMI1
510R4025
0.047uFC212
2 .2uFC4059 OPT
HPD2
D1-_HDMI4
0.1
uF
C4006OPT
2.4
K
R4023
+3.3V_Normal
33R4016OPT
0.1
uF
C290
OPT
BLM18PG121SN1DL211
CK-_HDMI1
D2+_HDMI2
1000pFC224OPT
VDD33
VDD33
24MHzX201
TU_CVBS
33R253
CK+_HDMI1
0.1
uF
C232
+3.5V_ST
MIUVDDC
10u
F
C284
10u
F
C4001
AUD_MASTER_CLK_0
+1.5V_DDR
0.047uFC219
BLM18PG121SN1DL227
D2+_HDMI4
2 .2uFC244
1uFC253
0R4004
TMUE312GABSW200
1
2 4
3
5
1K
3D
R206
1K
HD
R226
10uFC269
AV_CVBS_IN2
D2-_HDMI1
D1+_HDMI2
0.1
uF
C4046
68R254
0.1
uF
C4019
SC1_B+/COMP1_Pb+
100R289
2 .2uFC238
0.1
uF
C4031
+2.5V_Normal
68R231
SC1/COMP1_L_IN
IR
0 .1uFC251
+1.10V_V
DSUB_HSYNC
D0+_HDMI1
0 .1uFC286
AV_L_IN
AVDD_NODIE
D1-_HDMI1
10R217
68R252
0.047uFC218OPT
33R241OPT
SC1_R+/COMP1_Pr+
CK+_HDMI2
2 .2uFC239
4 .7uF10V
C200
AV_R_IN
+1.10V_VDDC
AVDD2P5
100pFC4068
0.047uFC215
D2+_HDMI1
1uFC4045
MODEL_OPT_3
BLM18SG121TN1DL202
0.1
uF
C4011
AVDD_MIU
10u
F
C275
10u
FC278
68R242
AVDD25_PGA
AUD_SCK
HPD1
0 .1uFC250
100R201 OPT
TU_SCL
AVDD2P5
0 .1uFC258
+3.5V_ST
HDMI_ARC
AVSS_PGA
BLM18SG121TN1D
L223
0.1
uF
C280
0.047uFC211
0.1
uF
C4012
0.1
uF
C4025
DDC_SCL_2
1K
PHM
_OFF
R212
0.1
uF
C4007
SIDE_USB_DP
100R203 OPT
D1+_HDMI4
AV_CVBS_IN2
MODEL_OPT_2
33R210
MODEL_OPT_1
68R238
1K
R209
NON
_DVB
_T2
D0-_HDMI2
0.1
uF
C4024
0.047uFC220OPT
1000pF
OPT
C203
VDD33
0.047uFC204
+3.3V_Normal
33R232
0.1
uF
C4009
100R288
+3.3V_Normal
0 .1uFC271
0.1
uF
C299
OPT
1K
PHM
_ON
R211
DTV/MNT_VOUT
BLM18PG121SN1DL208
AV_CVBS_IN0.047uFC4057OPT
0R4001
OPT
47R4003
0.047uFC225
47R4002
0 .1uFC4064
1K
NON
_3D
R207
SC1_ID
KDS181D200
1000p
F
OPT
C264
2 .2uFC242 OPT
0.1
uF
C4014
TU_SIF
62KR200
33R230
VDD33
100R204 OPT
0 .1uFC201
10u
F
C228
33R237OPT
1K
FHD
R227
DDC_SDA_1
DDC_SDA_4
0 .1uFC270
10uFC263
DDC_SCL_4
CEC_REMOTE_S7
1MR287
SCART1_Rout
0.1
uF
C4013OPT
D2-_HDMI2
SOC_RESET
68R256
0.1
uF
C4044
CK-_HDMI4
SC1/COMP1_R_IN
DSUB_G+
DDC_SDA_2
SIDE_USB_DM
0.047uFC222OPT
0.047uFC227
TU_SDA
AVDD_AU33
D2-_HDMI4
0.047uFC233
AUD_LRCK
AVDD_AU33
0.047uFC205 2 .2uFC4060 OPT
SOC_RESET 0 .1uFC4062
33R244
1000pFC217
DSUB_VSYNC
10u
F
C293
OPT
TP208
10u
F
C276
4 .7uFC249
0.1
uF
C292
OPT
SC1_FB
33R246
68R229
TP211
0 .1uFC273
AUD_LRCH
0.047uFC213
0 .1uFC241
10u
FC281 OPT
0 .1uFC256
IF_P_MSTAR
0.047uFC216
C4067
OPT
CK+_HDMI4
MIUVDDC
AVDD_MIU
33R249
FB_CORE
D0+_HDMI2
68R258
+1.10V_VDDC
D0-_HDMI4
BLM18PG121SN1DL204
100pFC4069
TP210
100R205
DSUB_B+
0.047uFC231
0 .1uFC274
0.047uFC207
0.1
uF
C267
BLM18PG121SN1DL228
BLM18PG121SN1DL229
0 .1uF16V
C4070
AVDD2P5_MOD
AVDD2P5_MOD
22pFC261
22pFC262
CI_DET0R297OPT
10KR4019
0
R4020
0.047uF25V
C4065
1K
R4027
OLED
1K
R4028D
VB
_S
1K
R4029
NON
_OLED1
K
R4030
NON
_DVB
_S
MODEL_OPT_4
MODEL_OPT_5
100R4031 OPT
100R4032 OPT
PM_MODEL_OPT_1
22R4033
22R4035
22R4034
22R4036
22R4037
22R4038
10uFC4071
0 .1uFC240
LGE2112-T8IC101
S7LR_DIVX_MS10
RXACKPJ2
RXACKNJ3
RXA0PK3
RXA0NJ1
RXA1PK2
RXA1NK1
RXA2PL2
RXA2NL3
DDCDA_DA/GPIO24T5
DDCDA_CK/GPIO23T4
HOTPLUGA/GPIO19V5
HOTPLUGB/GPIO20R5
RXCCKPAE9
RXCCKNAC9
RXC0PAC10
RXC0NAD9
RXC1PAC11
RXC1NAD10
RXC2PAE11
RXC2NAD11
DDCDC_DA/GPIO28AE8
DDCDC_CK/GPIO27AD8
HOTPLUGC/GPIO21AC8
RXDCKPF2
RXDCKNF3
RXD0PG3
RXD0NF1
RXD1PG2
RXD1NG1
RXD2PH2
RXD2NH3
DDCDD_DA/GPIO30R6
DDCDD_CK/GPIO29U6
HOTPLUGD/GPIO22P5
CEC/GPIO5R4
HSYNC0P2
VSYNC0R3
RIN0PN2
RIN0MP3
GIN0PN3
GIN0MN1
BIN0PM3
BIN0MM2
SOGIN0M1
HSYNC1V2
VSYNC1V3
RIN1PU3
RIN1MU2
GIN1PT1
GIN1MT2
BIN1PR2
BIN1MR1
SOGIN1T3
HSYNC2AA2
RIN2PY2
RIN2MAA3
GIN2PW2
GIN2MY3
BIN2PV1
BIN2MW3
SOGIN2W1
CVBS0AA8
CVBS1Y4
CVBS2W4
CVBS3AA5
CVBS4Y5
CVBS5AA4
CVBSOUT0Y6
CVBSOUT1AA1
VCOMAB4
VIFPAC4
VIFMAD3
IPAC3
IMAE3
SIFPAD4
SIFMAC5
IF_AGCAD2
RF_AGCAE2
I2C_SCKM1/GPIO75
AE6
I2C_SDAM1/GPIO76AD6
XINAD1
XOUTAC1
SPDIF_IN/GPIO152D7
SPDIF_OUT/GPIO153D6
USB0_DME3
USB0_DPE2
USB1_DMAC12
USB1_DPAE12
I2S_IN_BCK/GPIO150C8
I2S_IN_SD/GPIO151D8
I2S_IN_WS/GPIO149D9
I2S_OUT_BCK/GPIO156B10
I2S_OUT_MCK/GPIO154C9
I2S_OUT_SD/GPIO157B9
I2S_OUT_WS/GPIO155C10
AUL0AB9
AUR0AA11
AUL1Y9
AUR1AA9
AUL2AA7
AUR2AB8
AUL3Y8
AUR3Y10
AUL4AC7
AUR4AD7
AUOUTL0W6
AUOUTL2V6
AUOUTL3V4
AUOUTR0Y7
AUOUTR2W5
AUOUTR3U5
AUVRMAD5
AUVAGAE5
AUVRPAC6
EARPHONE_OUTLAA6
EARPHONE_OUTRAB6
ET_RXD[0]/RP/GPIO60C6
ET_TXD[0]/TP/GPIO57C5
ET_RXD[1]/RN/GPIO63A6
ET_TXD[1]/LED1/GPIO56C4
ET_TX_CLK/TN/GPIO59B5
ET_TX_EN/GPIO58C3
ET_MDC/GPIO61A3
ET_MDIO/GPIO62B3
ET_COL/LED0/GPIO55B4
IRIN/GPIO4N4
ARC0T6
HWRESETN5
LGE2112-TIC101
S7LR_DIVX_M
AVDDLV_USBK12
VDDC_1G9
VDDC_2H9
VDDC_3K10
VDDC_4K11
VDDC_5L10
VDDC_6M12
VDDC_7M13
VDDC_8N12
VDDC_9P14
VDDC_10P15
VDDC_11R10
VDDC_12R14
VDDC_13R15
VDDC_14T10
AVDD1P0P10
FB_COREP19
AVDDL_MODR16
AVDD10_LANL11
DVDD_DDRM14
AVDD2P5_ADC_1W9
AVDD2P5_ADC_2W10
AVDD2P5_ADC_3
W11
AVDD25_REFW12
AVDD25_LANY17
AVDD_MOD_1V18
AVDD_MOD_2U19
AVDD25_PGAW14
AVSS_PGAW15
AVDD_NODIEU7
AVDD_DVI_USB_1L7
AVDD_DVI_USB_2M7
AVDD3P3_MPLLP7
AVDD_DMPLLR7
DVDD_NODIEM19
AVDD_AU33V7
AVDD_EAR33W7
VDDP_1R19
VDDP_2T19
AVDD_LPLL_1W18
AVDD_LPLL_2W19
VDDP_NANDV19
AVDD_DDR0_D_1J17
AVDD_DDR0_D_2K15
AVDD_DDR0_D_3K16
AVDD_DDR0_CL15
AVDD_DDR1_D_1K17
AVDD_DDR1_D_2L17
AVDD_DDR1_D_3M17
AVDD_DDR1_CL16
GND_EFUSEE9
GND_1A23
GND_2B17
GND_3C23
GND_4A5
GND_5C11
GND_6C19
GND_7C22
GND_8D14
GND_9D18
GND_10D19
GND_11E17
GND_12E18
GND_13E19
GND_14E22
GND_15F8
GND_16F17
GND_17F18
GND_18F19
GND_19G8
GND_20H8
GND_21N22
GND_22N21
GND_23N20
GND_24M22
GND_25M21
GND_26M20
GND_27F10
GND_28V15
GND_29W16
GND_30V8
GND_31T18
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
GG
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
GN
MODEL_OPT_6
MODEL_OPT_7
1K
OPT
R291
1K
OPT
R290
1K
R294
1K
R293
100OPTR4040
100OPTR4039
10uHL203 OPT
10uHL205 OPT
EXT_L_AMP
EXT_R_AMP
GP3_S7LR
MAIN2, HW OPT 2
201
HDMI
AVDD_DDR1:55mA
DVB_S
MODEL_OPT_1
3D
AB2
Normal 2.5V
VDDC 1.05V
AVDD_NODIE:7.362mA
Normal Power 3.3V
AUDIO
IN
Close to MSTAR
PIN NO.
NON_3D
AVDD_DDR0:55mA
MODEL OPTION
PTION
MODEL_OPT_5
PHM_OFF
MODEL_OPT_0
COMP2
MODEL_OPT_2
VDDC : 2026mA
NON_DVB_T2
T24
RSDS Power OPT
OLED
TUNER_I2C
MODEL_OPT_3
LOW
ANALOG SIF
NON_DVB_S
C lose to IC w i th w id th t r ace
STby 3.5V
Close to MSTAR
F4
U23
PHM_ON
Close to MSTAR
SIDE USB
T25
SCART1_RGB/COMP1
Close to MSTAR
AB3
MODEL_OPT_4
PIN NAME
DDR3 1.5V
NON_OLED
FHD
CVBSIn/OUT
HD
SOC_RESET
HIGH
I2S_I/F
DSUB
DTV_IF
DVB_T2
AVDD2P5:172mA
AVDD25_PGA:13mA
MODEL_OPT_6
MODEL_OPT_7
B8
A8
READY
READY
READEY
READY
EXTERNAL SPEAKER
SCART OUT
ht 2012 LG Electronics. Inc. All right reserved. training and service purposes LGE Inte
-
7/25/2019 m Fl 67449109
26/41
MBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
ND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
AL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
+3.5V_ST
0 .1uFC451
OPT100K
R404PD_+12V
10KR430
0 .1uF16V
C404
+12V/+15V
NR8040T3R6N
3.6uHL415
AO3407AQ409
G
DS
PWM_DIM
2SC3052Q407
E
B
C
1/16W
56K1%
R441
22uF10V
C456
+3.5V_ST
560pF
50V
C467
10KOPT
R427
0.01uF25V
C436
0.01uF
1.5
K1%R
403
POWER_+24V
THERMAL
TPS54319TREIC403
1VIN_1
3GND_1
7
COMP
9 SS/TR
10 PH_1
11 PH_2
12 PH_313
BOOT
14
PWRGD
15
EN
16
VIN
_3
5
AGND
8
RT/CLK
6
VSENSE
4GND_2
2VIN_2 17
EP[GND]
MLB-201209-0120P-N2L404
1KR419
0 .1uF16V
C440
+3.3V_Normal
100pFC489
2SC3052Q405
E
B
C+3.3V
L413
10KR443
10KR421
0 .1uFC474
0 .1uF16V
C407
OPT
22uF10V
C453
0
POWER
_23_GND
R476
2.2KR407
OPT
3300pF50V
C493
K16
3.9KR606
PWM_PULL-DOWN_3.9K
10uF10V
C403
5.6
K
R440
22uF
10V
C472
4.7
K
R486
OPT
+24V
0
POWER_20_PWM_DIM
R484
+1.5V_DDR
POW
0
POWER
_16_GND
R412
+5V_Normal
CIS21J121L402-*1
47KR429
OPT
L412
10KR410
SMAW200-H24S2
SLIM_32~52P401
1912V
14 GND
93.5V
4 24V
18 INVON
13GND
8 GND
324V
1712V
12 3.5V
7GND
2 24V
16 GND/V-sync
113.5V
6 GND
1PWRON
20 A.DIM
15GND
10 3.5V
5GND
2112V 22 P.DIM1
23GND/P.DIM2 24 Err OUT
25
1/16W 330K 5%R432
INV_CTL
0 .1uF16V
C438
0 .1uF16V
C411
RSR025P03Q403
S D
G
100R415
POWER_18_INV_CTL
0 .1uF16V
C406
0.1uF
16VC425
4 .7uF16V
C423
OPT
3300pF
50V
C448
PANEL_CTL
1:AK10
THERMAL
AP7173-SPG-13 HF(DIODES)
IC407
3VCC
2PG
4EN
1IN
5 GND
6SS
7FB
8OUT
9
[EP]
0
POWER
_24_GND
R475
A_DIM
+3.5V_ST
2SC3052Q400
E
B
C
+1.10V_VDDC
22uF16V
C420
100R420
POWER_24_ERROR_OUT
2.2KR405
OPT
100
POWER_20_ERROR_OUT
R437
10uF
25V
C443
100R480
PD_+12V
0POWER_22_PWM_DIM
R471
1KR606-*1
PWM_PULL-DOWN_1K
+12V/+15V
10uF16V
OPT
C442
100
POWER_24_INV_CTL
R425
10KR462
NR8040T3R6N
3.6uHL406
MLB-201209-0120P-N2L402
+5V_USB
2SC3052Q401
E
B
C
2.2K
R445
RT1P141C-T112
Q402
1
2
3
22uF16V
C492
OPT
+3.3V_Normal
68uF35V
C426OPT
0 .1uF16V
C432
10K
R463
OPT
0 .1uF16V
C416OPT
0
POWER_24_PWM_DIM
R472
0.015uF50V
C4090.015uF
0 .1uF16V
C444
0 .1uF16VC
435
0 .1uF16V
C447
1uF10V
C494
100KR488
10K
R401
0 .1uF
16V
C476
0 .1uF
16V
C431
0 .1uF16V
C455
MLB-201209-0120P-N2L407
10uF10V
C430
+3.3V_Normal
33K
R439
1/10W
1.2
1K
1%R447
PD
_+12V
1R473
FM20020-24P404
NORMAL_32
19
14
9
4
18
13
8
3
17
12
7
2
16
11
6
1
20
15
10
5
21 22
23 24
25
3KR405-*1
PANEL_DISCHARGE_RES
0 .1uF16V
C408
OPT
0 .1uF16V
C412
PD_+12V
10K
OPT
R446
22KR435
OPT
PANEL_VCC
8.2
K1%R
482
POWER_+24V
0 .1uF50V
C418
0POWER_18_A_DIM
R451
3K
PANEL_DISCHARGE_RES
R407-*1
100pF50V
C439
+3.5V_ST
0.1uF
16V
C475
+3.5V_ST
10K
R426
100R402
10K
R433
2SC3052Q406
OPTE
B
C
+2.5V_Normal
+3.3V_Normal
10KR428
22KR438
FW20020-24SP403
NORMAL_EXPEPT_32
19
14
9
4
18
13
8
3
17
12
7
2
16
11
6
1
20
15
10
5
21 22
23 24
BLM18PG121SN1D
L420
+3.3V_Normal
+3.5V_ST
22K
R431OPT
10uF
10V
C461
ERROR_OUT
OPT
0
POWER_20_A_DIM
R453
+3.5V_ST
11K
1%
R607
BLM18PG121SN1DL403
BLM18PG121SN1DL425
NON_5V_TUNER
6.8K
OPT
R418
NCP803SN293
IC409
PD_+12V_PWR_DET_ON_SEMI
1
GND
3VCC 2 RESET
V_ST
CIS21J121L407-*1
0 .1uF
16V
C441
2.7
K
1%PD
_+12V
R448
+24V
CIS21J121
L404-*1
0POWER_22_A_DIM
R485
10KR434
POWER_ON/OFF_1
0 5%
PD
_+3.5
V
R450
4.7KR406
NCP803SN293
IC408
PWR_DET_ON_SEMI
1
GND
3VCC 2 RESET
12K
1%
R423 15K
R4361/16W
27K1%
R442
1/16W
4.3K
1%
R457
1/16W
4.7K1%R456
3300pF
C488
TJ3940S-2.5V-3L
IC402
1
GND
2 VOUT3VIN
0 .1uF
50V
C413
0
R608
0R400
OPT
FB_CORE
THERMAL
TPS54327DDARIC401
3VREG5
2VFB
4SS
1EN
5GND
6SW
7VBST
8VIN
9
[EP]GND
10KR489
10KR490OPT
201GP3_S7LR
POWER_LARGE 4
#13 #20
NC
16
NC
PWM_DIM
18
4A
NC
(PSU)
GND
R2
GND
INV_ON
New item
VBR-A
GND
SHARP
Max 1000mA
Vout=0.8*(1+R1/R2)=1.5319
PWM_DIM
PWM_DIM
Err_out
+1.5V_DDR
PWM_DIM
24
Err_out
CMO10"LED
PWM_DIM
INV_ON
$ 0.165
Vd=550mV
12V - ->3 .58V - -> 3 .82V (3 .68V )
23
INV_ON
GND
16
NC
INV_ON
LGD LPB/
GND
Err_out
IPS-@
+3.3V_Normal
--> NC
24
FROM LIPS & POWER B/D
PWM_DIM
R1
780 mA
NC
GND
LGD(PSU)
OS LPB
err_out
or LIPS
PANEL_POWER
out=(1+R1/R2)*0.765=5.03V
+3.5V_ST -> 3.375V
R1
(PSU)
err_out
2000 mA
32LE5300-TA
60:PWM
32LE5300-TA
INV_ON
PWM_DIM
INV_ON
1.5A
NC
D MODULE PIN MAP -> latest update 20100618>
22
LGD10"LED INV MAIN
60:NC
S7LR core 1.2V voltNC
(PSU)
GND
R2
(PSU) #11 #24
52/60:ERROR
300 mA
Vout=0.827*(1+R1/R2)=1.225V
GND
NC
GND
INV_ON
(PSU)
24V -->3 .78V - -> 3 .92V (3 .79V )
ST_3.5V--> 3.375V --> 3.46V
NC
AUO10"LED
NC
E PIN MAP>
--> NC
+2.5V/+1.8V
#12 #18
18
INV_ON
32LE4500-TA
N No
Power_D
NC
#14 #22
A-DIM
(PSU)
26/32HD:NC
NC
20
GND
NC
PWM_DIM
(PSU)
+5V_USB
LGD e d g e le d e r ro r -o u t u se o r n o t? c h e c k in g i s n e c e s sa ry . . .
R1
NC
3A
18 .5V - ->3 .5V - -> 3 .75V (3 .59V )
err_out
20
22
--> NC
AUO 10"LampN No
--> NC
err_out
26/32/52:PWM
23
CMO10"Lamp
NC
R2
26/32/52:GND
INV_ON
20V -->3 .51V - -> 3 .76V (3 .59V )
ht 2012 LG Electronics. Inc. All right reserved. training and service purposes LGE Inte
-
7/25/2019 m Fl 67449109
27/41
MBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
ND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
AL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
2SC3052Q2406
OPT EB
C
1000pF50V
C2404
+3.5V_ST
CDS3C05HDMI15.6V
D903
NEW_SUB
1.5KR2413LED_B/LG_LOGO
100R2402
JP2407
+3.5V_ST
S/T_SDA
S/T_SCL
LED_R/BUZZ
0 .1uF16V
C2403
18pF50VOPT
C907
JP2408+3.5V_ST
JP2411
AMOTECH5.6VD2402
47KR2429
OPT
CDS3C05HDMI15.6V
D902
NEW_SUB
10K
1%
R2405
18pF50VOPT
C2408
100pF50V
C2407
SENSOR_SCL
0 .1uFC2402
+3.5V_ST
0 .1uFC2401
47KR2425
OPT
47KR2431
OPT
1.5K
R2414
100
R2412
EYEQ/TOUCH_KEY
SENSOR_SDA
+3.3V_Normal
18pF50VOPT
C2409
0R2427
12507WR-12LP2401
OLD_SUB
1
2
3
4
5
6
7
8
9
10
11
12
13
+3.5V_ST
0 .1uF16V
C2405
JP2410
22R2428
10K
1%
R2404
KEY1
47KR2426
IR
0 .1uF16V
C2410
OPT
KEY2
JP2409
100R2401
12507WR-15LP2402
NEW_SUB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
15
100R2411
EYEQ/TOUCH_KEY
10KR2416OPT
BLM18PG121SN1DL2404
1000pF50V
C2406
2SC3052Q2405
OPT
E
BC
10KR2430
OPT
18pF50VOPT
C906
AMOTECH5.6VD2401
5.6VD2405
5.6V
D2403
EYEQ/TOUCH_KEY
5.6VD2404
EYEQ/TOUCH_KEY
BLM18PG121SN1DL2401
BLM18PG121SN1DL2402
BLM18PG121SN1DL2403
22
IR_OUT
R36
1KIR_OUT
R39
2SC3052IR_OUT
Q31 E
BC
+3.5V_ST
2SC3052IR_OUT_EU_ASIA
Q30
E
BC
1K IR_OUT_EU_ASIA
R37 +3.5V_ST
47K
IR_OUT
R40
IR_OUT
10K
IR_OUT_EU_ASIA
R38
0R41
IR_OUT_Brazil_USA
201
6
GP3_S7LR
IR/CONTROL-L
IR & LED
CONTROL
IR OUT
ht 2012 LG Electronics. Inc. All right reserved. training and service purposes LGE Inte
-
7/25/2019 m Fl 67449109
28/41
MBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
ND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
AL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
USB1_CTL
10KR1454
MLB-201209-0120P-N2
120-ohm
L1451
AP2191DSG
EAN61849601
IC1450
3IN_2
2
IN_1
4EN
1GND
5FLG
6OUT_1
7
OUT_2
8NC
CIS21J121
L1451-*1
USBDOWNSTREAM
3AU04S-305-ZC-(LG)
JK1450
USB_JACK
1
2
3
4
5
+5V_USB
10uF
10V
C1452
USB1_OCD
SIDE_USB_DM
0 .1uF
C1453
1/8W2K
1%
R1458
1/8W2K
1%
R1459
USBDOWNSTREAM
3AU04S-345-ZC-H-LG
JK1450-*1
USB_JACK_LV3400
1
2
3
4
5
4.7K
OPT
R1455
RCLAMP0502BA
D1451
OPT
SIDE_USB_DP
+3.3V_Normal22uF
16V
C1451
47R1451
201GP2R
USB_OCP_DIODE 7
USB_DIODES
$0.077
ht 2012 LG Electronics. Inc. All right reserved. training and service purposes LGE Inte
-
7/25/2019 m Fl 67449109
29/41
MBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
ND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
AL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
5V_DET_HDMI_4
D804
OPT
DDC_SDA_1
10K
R862
D1+_HDMI2
HDMI_CEC
D0-_HDMI1
GND
01
14
13
5D1_GND
0
LD