LTL17KGH5D-012A Product Data Sheet Through Hole Lamp · Tape Width W3 17.5 0.689 19.0 0.748 6 /10...

LITE-ON DCC

RELEASE

LITE-ON Technology Corp. / OptoelectronicsNo.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C.

Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660http://www.liteon.com/opto

Through Hole LampProduct Data SheetLTL17KGH5D-012A Spec No.: DS20-2009-0259Effective Date: 07/30/2015

Revision: A

BNS-OD-FC001/A4

BNS-OD-FC001/A4

BNS-OD-FC001/A4

BNS-OD-FC001/A4

1/10 Part No. : LTL17KGH5D-012A BNS-OD-FC002/A4

Through Hole Lamp LTL17KGH5D-012A

Through Hole Lamp

LTL17KGH5D-012A

Rev Description By Date

Above data for PD and Customer tracking only

- NPPR Receive and Upload on OPNC ORMJITM 01/08/2010

A Update DS Jeromy 06/30/2015



1. Description

Through hole LEDs are offered in a variety of packages such as 3mm, 4mm, 5mm, rectangular, and cylinder which are suitable

for all applications requiring status indication. Several intensity and viewing angle choices are available in each color for design

flexibility.

1. 1. Features

Low power consumption & High efficiency

High luminous intensity output

Lead (Pb) free product - RoHS Compliant

Popular T-1 diameter

Versatile mounting on P.C. Board or panel

I.C. Compatible/low current requirement

AlInGaP Green Lamp & Green Color Diffused Lens

1.2. Applications

Communication

Computer

Consumer

Home appliance

Industrial

2. Outline Dimensions

Notes :

1. All dimensions are in millimeters (inches).

2. Tolerance is ±0.25mm (.010") unless otherwise noted.

3. Protruded resin under flange is 1.0mm (.04") max.

4. Lead spacing is measured where the leads emerge from the package.

5. Specifications are subject to change without notice.



3. Absolute Maximum Ratings at TA=25°C

Parameter Maximum Rating Unit

Power Dissipation 75 mW

Peak Forward Current

(1/10 Duty Cycle, 0.1ms Pulse Width) 60 mA

DC Forward Current 30 mA

Derating Linear From 50°C 0.4 mA/°C

Operating Temperature Range -40°C to + 100°C

Storage Temperature Range -55°C to + 100°C

Lead Soldering Temperature

[2.0mm(.0787") From Body] 260°C for 5 Seconds Max

4. Electrical / Optical Characteristics at TA=25°C

Parameter Symbol Min. Typ. Max. Unit Test Condition

Luminous Intensity IV 110 180 520 mcd IF = 20mA

Note 1

Viewing Angle 2θ1/2 50 deg Note 2 (Fig.6)

Peak Emission Wavelength λP 574 nm Measurement

@Peak (Fig.1)

Dominant Wavelength λd 566 571 578 nm Note 4

Spectral Line Half-Width Δλ 11 nm

Forward Voltage VF 2.1 2.4 V IF = 20mA

Reverse Current IR 100 μA VR = 5V, Note 6

NOTE:

1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve.

2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.

3. Iv classification code is marked on each packing bag.

4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines

the color of the device.

5. Iv guarantee must be included with ±15% testing tolerance.

6. Reverse voltage (VR) condition is applied for IR test only. The device is not designed for reverse operation.



5. Typical Electrical / Optical Characteristics Curves

(25°C Ambient Temperature Unless Otherwise Noted)



6. Taping Features * Compatible with radial lead automatic insertion equipment.

* Most radial lead plastic lead lamps available packaged in tape and folding.

* 2.54mm (0.1") straight lead spacing available.

* Folding packaging simplifies handling and testing.

* Reel packaging is available by removing suffix “A” on option.

Package Dimensions

Specification

Item Symbol Minimum Maximum

mm inch mm inch

Tape Feed Hole Diameter D 3.8 0.149 4.2 0.165

Component Lead Pitch F 2.3 0.091 3.0 0.118

Front to Rear Deflection △H -- -- 2.0 0.078

Feed Hole to Bottom of Component H1 21.5 0.846 22.5 0.886

Feed Hole to Overall Component Height H2 26.6 1.047 28.2 1.110

Lead Length After Component Height L W0 11.0 0.433

Feed Hole Pitch P 12.4 0.488 13.0 0.511

Lead Location P1 4.4 0.173 5.8 0.228

Center of Component Location P2 5.05 0.198 7.65 0.301

Total Tape Thickness T -- -- 0.90 0.035

Feed Hole Location W0 8.5 0.334 9.75 0.384

Adhesive Tape Position W2 0 0 3.0 0.118

Tape Width W3 17.5 0.689 19.0 0.748



7. Packing Spec.

Total 3,000pcs per inner carton

10 Inner cartons per outer carton

Total 30,000 pcs per outer carton

In every shipping lot, only the last pack will be non-full packing



8. Bin Table Specification

Luminous Intensity Unit : mcd @20mA

Bin Code Min. Max.

FG 110 180

HJ 180 310

KL 310 520

Note: Tolerance of each bin limit is ±15%

Dominant Wavelength Unit : nm @20mA

Bin Code Min Max

H06 566.0 568.0

H07 568.0 570.0

H08 570.0 572.0

H09 572.0 574.0

H10 574.0 576.0

H11 576.0 578.0

Note: Tolerance of each bin limit is ±1nm



9. CAUTIONS

9.1. Application

This LED lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment.

9.2. Storage

The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity. It is recommended that

LEDs out of their original packaging are used within three months. For extended storage out of their original packaging, it is

recommended that the LEDs be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen

ambient.

9.3. Cleaning

Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary.

9.4. Lead Forming & Assembly

During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens. Do not use the base of the

lead frame as a fulcrum during forming. Lead forming must be done before soldering, at normal temperature. During assembly

on PCB, use minimum clinch force possible to avoid excessive mechanical stress.

9.5. Soldering

When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point. Dipping the lens into the

solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high

temperature.

Recommended soldering conditions:

Soldering iron Wave soldering

Temperature

Soldering time

Position

350°C Max.

3 seconds Max.

(one time only)

No closer than 2mm

from the base of the epoxy bulb

Pre-heat

Pre-heat time

Solder wave

Soldering time

Dipping Position

100°C Max.

60 seconds Max.

260°C Max.

5 seconds Max.

No lower than 2mm from the

base of the epoxy bulb

Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic

failure of the LED. IR reflow is not suitable process for through hole type LED lamp product.

9.6. Drive Method

An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an

application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as

shown in Circuit A below.

Circuit model (A) Circuit model (B)

LED

LED

(A) Recommended circuit

(B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs.



9.7. ESD (Electrostatic Discharge)

Static Electricity or power surge will damage the LED.

Suggestions to prevent ESD damage:

Use a conductive wrist band or anti- electrostatic glove when handling these LEDs

All devices, equipment, and machinery must be properly grounded

Work tables, storage racks, etc. should be properly grounded

Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic

lens as a result of friction between LEDs during storage and handing

Suggested checking list:

Training and Certification

9.7.1.1. Everyone working in a static-safe area is ESD-certified?

9.7.1.2. Training records kept and re-certification dates monitored?

Static-Safe Workstation & Work Areas

9.7.2.1. Static-safe workstation or work-areas have ESD signs?

9.7.2.2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V?

9.7.2.3. All ionizer activated, positioned towards the units?

9.7.2.4. Each work surface mats grounding is good?

Personnel Grounding

9.7.3.1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes

with conductive flooring?

9.7.3.2. If conductive footwear used, conductive flooring also present where operator stand or walk?

9.7.3.3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*?

9.7.3.4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs?

9.7.3.5. All wrist strap or heel strap checkers calibration up to date?

Note: *50V for Blue LED.

Device Handling

9.7.4.1. Every ESDS items identified by EIA-471 labels on item or packaging?

9.7.4.2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation?

9.7.4.3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items?

9.7.4.4. All flexible conductive and dissipative package materials inspected before reuse or recycle?

Others

9.7.5.1. Audit result reported to entity ESD control coordinator?

9.7.5.2. Corrective action from previous audits completed?

9.7.5.3. Are audit records complete and on file?

10/10

Part No. : LTL17KGH5D-012A BNS-OD-FC002/A4


10. Reliability Test

Classification Test Item Test Condition Sample Size Reference Standard

Endurance

Test

Operation Life

Ta = Under room temperature IF = per datasheet maximum drive current Test Time= 1000hrs

22 PCS (CL=90%; LTPD=10%)

MIL-STD-750D:1026 (1995) MIL-STD-883G:1005 (2006)

High Temperature High Humidity storage

Ta = 60°C RH = 90% Test Time= 240hrs

22 PCS (CL=90%; LTPD=10%)

MIL-STD-202G:103B (2002) JEITA ED-4701:100 103 (2001)

High Temperature Storage

Ta= 105 ± 5°C Test Time= 1000hrs

22 PCS (CL=90%; LTPD=10%)

MIL-STD-750D:1031 (1995) MIL-STD-883G:1008 (2006) JEITA ED-4701:200 201 (2001)

Low Temperature Storage

Ta= -55 ± 5°C Test Time= 1000hrs

22 PCS (CL=90%; LTPD=10%)

JEITA ED-4701:200 202 (2001)

Environmental

Test

Temperature Cycling

100°C ～ 25°C ～ -40°C ～ 25°C

30mins 5mins 30mins 5mins 30 Cycles

22 PCS (CL=90%; LTPD=10%)

MIL-STD-750D:1051 (1995) MIL-STD-883G:1010 (2006) JEITA ED-4701:100 105 (2001) JESD22-A104C (2005)

Thermal Shock

100 ± 5°C ～ -30°C ± 5°C

15mins 15mins 30 Cycles (<20 secs transfer)

22 PCS (CL=90%; LTPD=10%)

MIL-STD-750D:1056 (1995) MIL-STD-883G:1011 (2006) MIL-STD-202G:107G (2002) JESD22-A106B (2004)

Solder Resistance

T.sol = 260 ± 5°C Dwell Time= 10±1 seconds 3mm from the base of the epoxy bulb

11 PCS (CL=90%; LTPD=18.9%)

MIL-STD-750D:2031(1995) JEITA ED-4701: 300 302 (2001)

Solderability

T. sol = 245 ± 5°C Dwell Time= 5 ± 0.5 seconds (Lead Free Solder, Coverage ≧95% of

the dipped surface)

11 PCS (CL=90%; LTPD=18.9%)

MIL-STD-750D:2026 (1995) MIL-STD-883G:2003 (2006) MIL-STD-202G:208H (2002) IPC/EIA J-STD-002 (2004)

Soldering Iron T. sol = 350 ± 5°C Dwell Time= 3.5 ± 0.5 seconds

11 PCS (CL=90%; LTPD=18.9%)

MIL-STD-202G:208H (2002) JEITA ED-4701:300 302 (2001)

11. Others

The appearance and specifications of the product may be modified for improvement, without prior notice.

LTL17KGH5D-012A Product Data Sheet Through Hole Lamp · Tape Width W3 17.5 0.689 19.0 0.748 6 /10...

Documents

Transcript of LTL17KGH5D-012A Product Data Sheet Through Hole Lamp · Tape Width W3 17.5 0.689 19.0 0.748 6 /10...