LOW PRESSURE MOTOR VALVES - Kimray E2:115.1 Issued 2/16 Current Revision: Add Certifications LOW...
Transcript of LOW PRESSURE MOTOR VALVES - Kimray E2:115.1 Issued 2/16 Current Revision: Add Certifications LOW...
www.kimray.comE2:115.1
Issued 2/16Current Revision:Add Certifications
LOW PRESSURE MOTOR VALVES
MT BP5 SPRING LOADED BACK PRESS. w/REDUCED INNER VALVE
CERTIFICATIONS: Canadian Registration Number (CRN): 0C15676.24567890NTY (Ductile) 0C15331.24567890NTY (Steel)
CONSTRUCTION: Body and housings are available in cast iron, ductile iron or steel. Valve stem is 303 stainless steel. Spring is stainless steel. Diaphragm and seating materials are oil resistant synthetic rubber or polyurethane. After assembly each valve is given a complete operational test.
OPERATION: The Stem Assembly is the only moving unit in the motor valve. The PRELOAD SPRING loads the Stem Assembly and is opposed by Upstream Pressure (Green) on the under side of the DIAPHRAGM plus the differential of Upstream Pressure (Green) minus Downstream Pressure (Blue) across the INNER VALVE SEAT. An increase in Upstream Pressure (Green) exceeding the set pressure of the PRELOAD SPRING moves the Stem Assembly upward, opening the INNER VALVE SEAT. A decrease in Upstream Pressure (Green) decreases the force on the INNER VALVE SEAT and DIAPHRAGM allowing the PRELOAD SPRING to move the Stem Assembly down-ward reducing the flow from Upstream Pressure (Green) to Downstream Pressure (Blue). The interaction between the PRELOAD SPRING and the Upstream Pressure (Green) on the INNER VALVE SEAT and the DIAPHRAGM will cause the valve to open or close the amount required to maintain the Upstream Pressure (Green) set by the ADJUSTING SCREW.
Stem AssemblyUpstream PressureDownstream Pressure
Inner Valve Seat
Diaphragm
Preload Spring
Adjusting Screw
Oil
APPLICATIONS: Liquid or gas systems where a 0 to 125 psig adjustable back pressure is desired, such as treaters, free water knockouts, pressure vessels, vent lines on separators, flow treaters, com-pressor stations, and gas gathering systems.
FEATURES: Single adjustment Single soft seat Removable valve seat Internal sense line Minimum maintenance All internal parts can be removed with valve in line Spring adjustment • 0 to 10 psig. • 10 to 20 psig. • 20 to 40 psig. • 40 to 65 psig. • 65 to 90 psig. • 80 to 125 psig.
Kimray is an ISO 9001- certified manufacturer.
Cf & Cv VALUESLine Size Trim Size Cf Cv
1" .50" 0.86 5.62" 1.25" 0.84 24.03" 1.62" 0.82 34.2
www.kimray.comE2:115.3Issued 2/18
Current Revision:Add 3 inch valves
LOW PRESSURE MOTOR VALVES
MT BP5 SPRING LOADED BACK PRESS. w/REDUCED INNER VALVEDUCTILE IRON
THRU VALVES AVAILABLE: NOTES:
CAT. SIZE MOTOR OPER MAX. NO. TYPE VALVES PRESS W.P. KIT
CAT. SIZE MOTOR OPER MAX. NO. TYPE VALVES PRESS W.P. KIT
ALU1 2" SCRD. 201 SMT BP5-D 0-10 300 RTB1ALU2 2" SCRD. 202 SMT BP5-D 10-20 300 RTB1ALU4 2" SCRD. 204 SMT BP5-D 20-40 300 RTB1ALU6 2" SCRD. 206 SMT BP5-D 40-65 300 RTB1ALU9 2" SCRD. 209 SMT BP5-D 65-90 300 RTB1ALU12 2" SCRD. 212 SMT BP5-D 80-125 300 RTB1ALV1 2" GRVD. 201 GMT BP5-D 0-10 300 RTB1ALV2 2" GRVD. 202 GMT BP5-D 10-20 300 RTB1ALV4 2" GRVD. 204 GMT BP5-D 20-40 300 RTB1ALV6 2" GRVD. 206 GMT BP5-D 40-65 300 RTB1ALV9 2" GRVD. 209 GMT BP5-D 65-90 300 RTB1
Oil
Line Size2"3"
Screwed17091634
Flanged19131914
Grooved2964--
Diaphragm 5369, 2"*743, 3"
*Back Up 149T to 150T, 2 Req’d.
Nut 1897
Upper Spring Guide 1888
Spring
5370 (25 lbs.) Blue, 2"5336 (40 lbs.) Green, 2"2013 (65 lbs.) Yellow, 2"5371 (90 lbs.) Orange, 2"4006 & 6763 (125 lbs.) Red, 2"
5368 (10 lbs.) Silver, 2"
4006 (40 lbs.) Red, 3"
Lock Nut 173*Body
Plug 699
Plug 699
Bonnet 2031, 2"4581, 3"
Stem 3070, 2"4582, 3"
Upper Diaphragm Plate 737, 2"733, 3"
Screw 965, 8 Req’d. 2"907, 10 Req’d. 3"
Housing 1704, 2"1632, 3"
*Gasket 196, 2"197, 3"
*Seat 310P, 2"1230P, 3"
Ratio Plug 1539
Gasket 276, 2"277, 3"
Lower Spring Guide 2029, 2"4591, 3"
Lower Diaphragm Plate 323SS6, 2"738, 3" O Ring 154Q, 2"*
155, 3"
Seat Disc 312, 2"1229, 3"
Removable Seat 4005, 2"1219D, 3"
Removable Seat Wrench 706SW, 2"1219SW, 3"
Plug 699
Lock Nut 173, 2"*906, 3"
Adjusting Screw 6911, 2”7546, 3”
ALV12 2" GRVD. 212 GMT BP5-D 80-125 300 RTB1ALW1 2" FLGD. 201 FMT BP5-D 0-10 250 RTB1ALW2 2" FLGD. 202 FMT BP5-D 10-20 250 RTB1ALW4 2" FLGD. 204 FMT BP5-D 20-40 250 RTB1ALW6 2" FLGD. 206 FMT BP5-D 40-65 250 RTB1ALW9 2" FLGD. 209 FMT BP5-D 65-90 250 RTB1ALW12 2" FLGD. 212 FMT BP5-D 80-125 250 RTB1ENQ 3" SCRD. 304 SMT BP5-D 10-40 175 RTD1ENR 3" FLGD. 304 FMT BP5-D 10-40 175 RTD1 *These are recommended spare parts and are stocked as repair kits.For dimensions refer to Table of Contents.
Kimray is an ISO 9001- certified manufacturer.
www.kimray.comE2:120.1
Issued 1/13Current Revision:Change Logo
LOW PRESSURE MOTOR VALVES
LIQUID CAPACITY CHART
CAPACITY - Blds. Water/Day, Steady Row
For gravity correction, multiply the above figures byWhere “G” is the specific gravity of the flowing liquid.
1G
SINGLE ACTING MOTOR VALVES
WITH REDUCED INNER VALVES
PRESSURE DROP
ACROSS VALVE PSIG.
VALVE SIZE-INCHES
1
12345
101520304050607080
100125
105150180210235330405465575660740810875935
1,0451,170
7451,0601,3001,5001,7002,3002,9003,3004,1004,7005,3005,8006,2006,7007,5008,400
1,7602,5003,0503,5003,9005,6006,8007,9009,600
11,10012,40013,60014,70015,70017,60019,700
3,3504,9006,1007,0007,800
11,00013,50015,60019,20022,10024,80027,10029,30031,30033,50038,200
7,80011,00013,50015,60017,50024,70030,20034,90042,70049,30055,20060,50065,40069,80078,20087,500
2 3 4 6
12345
101520304050607080
100125
263745525982
101116145165185200220230260290
290410510590660900
1,1301,2901,6001,8402,0702,2602,4202,6202,9403,280
515735895
1,0251,1401,6402,0002,3202,8203,2603,6404,0004,3004,6005,1505,750
1,9502,7503,3703,9004,3756,1757,5508,725
10,67512,30013,80015,10016,35017,45019,50021,900
6
VALVE SIZE-INCHES
1
PRESSURE DROP
ACROSS VALVE PSIG.
8351,2251,5251,7501,9502,7503,3703,9004,8005,5006,2006,7507,3007,8008,3509,800
2 3 4
www.kimray.comE2:120.2Issued 1/13
Current Revision:Change Logo
LOW PRESSURE MOTOR VALVES
LIQUID CAPACITY CHART
CAPACITY - Blds. Water/Day, Steady Row
DOUBLE ACTING MOTOR VALVES
ADJUSTABLE DOUBLE ACTING WITH REDUCED INNER VALVES
WITH REDUCED INNER VALVES
For gravity correction, multiply the above figures byWhere “G” is the specific gravity of the flowing liquid.
1G
PRESSURE DROP
ACROSS VALVE PSIG.
ADAB
12345
101520304050607080
100125
101143175200225320390450555640710780845905
1,0101,105
PRESSURE DROP
ACROSS VALVE PSIG.
VALVE SIZE-INCHES
1
12345
101520304050607080
100125
405573702810905
1,2801,5701,8102,2202,5602,8603,1303,3803,6204,0504,520
1,5202,1502,6303,0403,4004,8005,8806,8008,3209,600
10,75011,78012,70013,60015,20016,900
3,1504,4605,4506,3007,0309,980
12,20014,10017,30019,90022,30024,40026,40028,20031,50035,200
5,8308,250
10,70011,70013,10018,50022,60026,10031,90036,90041,30045,20048,80052,10058,30065,100
13,15018,60022,80026,30029,40041,70050,90058,80072,00083,10093,000
102,000110,000117,500131,500147,000
2 3 4 6
12345
101520304050607080
100125
101143175200225320390450555640710780845905
1,0101,105
7401,0401,2801,4751,6502,3302,8753,3004,0504,6505,2005,7006,1506,6007,3758,200
1,0801,5251,8602,1502,4003,4004,1504,8005,9006,8007,6008,3509,0009,650
10,80012,000
3,7405,3306,5307,5508,400
11,95014,60016,85020,60023,80026,60029,20031,50033,60037,40042,000
6
VALVE SIZE-INCHES
1
PRESSURE DROP
ACROSS VALVE PSIG.
1,6502,3402,8603,3003,7005,2506,4007,4009,050
10,50011,70012,80013,80014,80016,50018,450
2 3 4
www.kimray.comE2:120.3
Issued 3/18Current Revision:Add "H" dimension to 3 inch
LOW PRESSURE MOTOR VALVES
DIMENSIONS
18 1/2
18 1/2
7 1/2
4 3/8
LINESIZE
1" SCRD
SCRD
FLGD
GRVD
SCRD
FLGD
FLGD
FLGD
SCRD
2"
3"
4"
6"
BODYSTYLE A
4 3/8
8 3/4
12
8 1/2
9
12 3/16
15
15 1/8
22 1/8
1 1/8
2 1/8
3 1/16
2 1/8
4
3
8
18 1/2
3 3/4
4 1/2
5 1/2
2 3/4 3 3/8
4 3/8
5 7/8
5 7/8
6 7/8
6 7/8
6 7/84 3/8
7 1/2
11
3 3/8
5 7/8
8 8
88
9 1/2
9 1/2
3 3/8
6 7/8
6 7/8
6 7/8
8
8
9 1/2
9 1/2
15 1/4
5 7/8
5 7/8
9 3/4
9 3/4
16
B C D E F G H
FLANGE DIMENSIONS ARE ASA 150 LB. STANDARD.
MT (SINGLE ACTING MOTOR VALVE)MT-5 (WITH REDUCED INNER VALVES)
MT-2DA, MT-4DA (DOUBLE ACTING MOTOR VALVE)MT-2DA5, MT-4DA5 (WITH REDUCED INNER VALVES)
MT-DA (DOUBLE ACTING MOTOR VALVE)MT-DA5 (WITH REDUCED INNER VALVES)
MT-ADA, MT ADAB (ADJUSTABLE DOUBLE ACTING)MT BP, MT BP5 (SPRING LOADED BACK PRESSURE)
20
20