LOCATOR - MaxFacWhen tightening abutment by hand When removing replacement male from denture cap...
Transcript of LOCATOR - MaxFacWhen tightening abutment by hand When removing replacement male from denture cap...
LOCATOR� SystemLOCATOR� System
HIOSSEN Inc. www.hiossen.com85 Ben Fairless Dr, Fairless Hills, PA 19030, USA TEL : 1-888-678-0001 FAX : 1-267-759-7004
HIOSSEN LOCATOR� SYSTEM
03HIOSSEN
LOCATOR� SYSTEM LOCATOR� SYSTEM
HIOSSEN LOCATOR� SYSTEM
■ Features- Stable dual retention & optimal holding capabilities
against various retention forces (6N, 12N, 22N)
- Excellent durability
- Possible denture restorations even at small vertical
dimension
- Accommodate up to 40。divergence between two
implants
- Retention males can be easily placed & removed
with core tool
■ Indications- Implant retained overdenture in the mandible or
maxilla.
■ Contraindications- Tooth and implant supported overdenture
- Divergences greater than 40。between two
implants.
HIOSSEN LOCATOR� SYSTEM
Replacement Male
Denture Cap
Black ProcessingMale
Lab Analog
Core Tool
0。~10。divergence 10。~20。divergence
Description Component Flow Diagram Tool
Impression Coping
Abutment
Fixture
Block out spacer
HS System HG SystemTorque Driver
05HIOSSEN04 HIOSSEN LOCATOR� SYSTEM
Procedure of LOCATOR� SYSTEM
■ Fabricating individual tray
Note
Connect healing abutments
�During wax rim fabrication, use denture cap with blackprocessing male for retention on bite registration.
�Selecting the replacement malesIn the case of implant divergences of more than10。to 20。, using extended range replacement males (red or green) can give much retention and durability.
When selecting males, it is recommended to use theBlue male (least retention) first. If the patients feelsthat they are too loose, then use the ones with greaterretention force.
Blue � Pink � Clear
Take impression Fabricate Individual tray Fabricate metal frameon the denture caps
Denture curing Remove black processing maleusing core tool
① ②
■ Curing denture & changing replacement males (Basic procedure)
■ Taking impression & Fabricating working model
Tighten Abutments (30Ncm) Connected LOCATOR� abutments Connect impression copings
④③ ⑤
⑫⑪ ⑬
insert replacement male usingcore tool
Locator overdenture Setting
⑮⑭ �
Obtained denture cap positionsafter the curing
Resin spill way on thelingual surface
■ Curing denture & changing replacement males (Intra-oral Technique)
⑫⑪ ⑬
Insert block out spacer Connect black processing maleinserted denture caps
Apply self-curing resin
⑮⑭ �
Try-on & curing Remove excessive resin Remove black processing maleusing core tool
�� �
insert replacement male usingcore tool
Locator overdenture Setting
�� �
Connected lab analogs Fabricate working model Place black processing maleinserted denture caps
⑨⑧ ⑩
Take impression
Upper abutment margin should beover 1.0mm from the mucosa level
Connect lab analogs
⑥ ⑦
1mm
Fabricate metal frame after blockingout the denture cap area
LOCATOR� SYSTEM LOCATOR� SYSTEM
07HIOSSEN06 HIOSSEN LOCATOR� SYSTEM
HIOSSEN LOCATOR� SYSTEM
■ Fixture level Impression
When using Hiossen fixture level impression components, It is also possible to take impression at the level of fixture withoutLOCATOR� abutment.
■Using The LOCATOR� Core Tool
Pick-up
Pick-up
Fixture Impression Coping
Fixture Impression Coping
▶When inserting replacement males into denture cap
▶When tightening abutment by hand
▶When removing replacement male from denture cap
Fixture Lab Analog
Fixture Lab Analog
Transfer
Transfer
HS System
HS LOCATOR� Abutment
Component & Tool
LOCATOR�
Impression Coping (4Pack)
LOCATOR� Core Tool
LOCATOR� Male Processing Kit (2Pack)
LICS
LMPS
HG LOCATOR� Abutment
HG System
① ②
③ ④
⑤ ⑥
Gap
① Unscrew the tip until the gap betweenthe tip & the body is visible
② Press on the male inside of denturecap with the tip and remove.
③ Twist the tip clock-wise until the maleseparates.
P
1.5mm
G/H
Regular
P : ∅4.8 ∅4.8 x 0.7mm HSLCA4810R
∅4.8 x 2.0mm HSLCA4820R
∅4.8 x 3.0mm HSLCA4830R
∅4.8 x 4.0mm HSLCA4840R
Platform x G/H Code
D
Fixture level
1.5mm
G/H
Mini
∅3.7 x 1.0mm HGLCA3510M
∅3.7 x 2.0mm HGLCA3520M
∅3.7 x 3.0mm HGLCA3530M
∅3.7 x 4.0mm HGLCA3540M
∅3.7 x 5.0mm HGLCA3550M
Diameter x G/H Code
D
Fixture level
1.5mm
G/H
Standard
∅3.7 x 1.0mm HGLCA4010S
∅3.7 x 2.0mm HGLCA4020S
∅3.7 x 3.0mm HGLCA4030S
∅3.7 x 4.0mm HGLCA4040S
∅3.7 x 5.0mm HGLCA4050S
Diameter x G/H Code
LOCATOR�
Lab Analog (4Pack)
LAL40S
LCCT
LOCATOR� Torque Driver
TWLDL TWLDS
LAL50S
LOCATOR� Replacement Male (4Pack)
LRM06S
6N
LRM12S
12N
LRM22S
22N
LOCATOR� Extended Replacement Male (4Pack)
LEM06S
LOCATOR� Black Processing Male (4Pack)
LBPS
LOCATOR� Block-out Spacers (20 pack)
6N
LEM12S
12N
LBSS
LOCATOR� SYSTEM LOCATOR� SYSTEM