Listing Constructional Data Report (CDR) · PDF fileListing Constructional Data Report (CDR)...
-
Upload
nguyendang -
Category
Documents
-
view
246 -
download
4
Transcript of Listing Constructional Data Report (CDR) · PDF fileListing Constructional Data Report (CDR)...
Listing Constructional Data Report (CDR)
Report Number 100739742CHI-001 Original Issued: 2-Oct-2012 Revised: None
Standard(s)
Applicant Manufacturer
Address Address
Country Country
Contact Contact
Phone Phone
FAX FAX
Email Email
1.0 Reference and Address
3M Company
3M New Ulm Manufacturing
Standard for Safety for Low Voltage Lighting Systems (ANSI/UL 2108 - 1st Edition, with
revisions through 04/27/11)
&
Standard for Safety for Luminaires (CAN/CSA C22.2 No. 250.0-08, 3rd Ed., with revisions
through 01/11/10)
1617 N FRONT ST
PO BOX 95
(651) 736-1432 (507) 359-0386
Building 223-5S-01
St. Paul, MN 55144
Mr. Brad Dieringer Mr. Vince Mueller
USA USA
Page 1 of 16
Report No. 100739742CHI-001
3M CompanyPage 2 of 16 Issued: 2-Oct-2012
Revised: None
Product
Brand name
Models
Model Similarity
Ratings
Other Ratings
2.0 Product Description
Low Voltage Luminaire
NA
NA
All models are constructed the same only differing in diameter.
Ratings 24VDC, max wattage per max dimensions shown in Illustration 1.
Description
The product covered by this report are low voltage LED pendant luminaires provided with a
means of permanent connection to a Listed Class 2 power source with a single connection to
the branch circuit in accordance with all local and national electrical codes.
Air
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 3 of 16 Issued: 2-Oct-2012
Revised: None
Photo 1 - Front open view of AIR Series, which is representative of all models.
Photo 2 - Close up view of frame
3.0 Product Photographs
2
3
2
3
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 4 of 16 Issued: 2-Oct-2012
Revised: None
3.0 Product Photographs
Photo 3 - Overall internal view.
Photo 4 - Mounting canopy
4
5
6
9
10
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 5 of 16 Issued: 2-Oct-2012
Revised: None
3.0 Product Photographs
Photo 5 - Mounting CableGrip
10
11
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 6 of 16 Issued: 2-Oct-2012
Revised: None
Photo #
Item
no.1 Name
Manufacturer/
trademark2 Type / model
2 Technical data and securement
means
Mark(s) of
conformity3
1 1 Labeling System Various Various
Not shown. Suitable for aluminum
surfaces, indoor dry location,
minimum 40°C
cURus,
cCSAus
1 2 Frame Various Various
Aluminum, minimum 0.41mm
thick, see Illustration 1 for
dimensions.
NR
1 3 Canopy Various VariousAluminum, minimum 0.41mm
thick.NR
3 4Rear Reflector
Film
3M COMPANY
ARCHITECTURA
L MARKETS
DEPT
Specular FilmRated minimum HB, 90°C, on
internal housing.cURus
3 5 LED Various VariousRated max. 3.4V, 500mA, see
Illustration 2 for LED strip details.NR
3 6 PCB Various Various
In Class 2 circuit, minimum HB,
90°C, secured to housing with
adhesive backing.
UR
3 7 Secondary Cable Various Various
Not shown. In Class 2 circuit,
minimum 24AWG, rated 24V,
90°C.
cULus
3 8 Bushings Various VariousNot shown. Suitable for secondary
cable, secured to housing.UR, CSA
4 9 Aircraft Cable Various VariousMinimum 1/16" cable, secured by
GripLock system below.NR
4,5 10 Gripper Various Various
Approved for Minimum 1/16"
aircraft cable, 50lbs. Typical by
Griplock, Type 15 and Type 18
Series, secured to housing.
cULus
5 11 Diffuser Various Various Rated minimum HB, 60°C. UR
5 12 Diffuser Adhesive
3M COMPANY
INDUSTRIAL
ADHESIVES &
TAPES DIV
VHB Tapes
4920, 4930,
4950
Not shown. Used to secure
diffuser, minimum 75°C.UR
3) Indicates specific marks to be verified, which assures the agreed level of surveillance for the component. "NR" - indicates Unlisted and
only visual examination is necessary. "See 5.0" indicates Unlisted components or assemblies to be evaluated periodically refer to section
5.0 for details.
4.0 Critical Components
NOTES:
1) Not all item numbers are indicated (called out) in the photos, as their location is obvious.
2) “Various“ means any type, from any manufacturer that complies with the "Technical data and securement means" and meets the "Mark(s)
of conformity" can be used.
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 7 of 16 Issued: 2-Oct-2012
Revised: None
No Unlisted CEC components are used in this report.
5.0 Critical Unlisted CEC Components
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 8 of 16 Issued: 2-Oct-2012
Revised: None
2. Mechanical Assembly - Components such as switches, fuseholders, connectors, wiring terminals and display
lamps are mounted and prevented from shifting or rotating by the use of lockwashers, starwashers, or other
mounting format that prevents turning of the component.
3. Corrosion Protection - All ferrous metal parts are protected against corrosion by painting, plating or the
equivalent.
4. Accessibility of Live Parts - All parts are located in a Class 2 circuit, no risk of fire or shock exists.
5. Grounding - This product is not provided with a means of grounding as it is located in a Class 2 circuit, no
risk of shock exists.
6. Internal Wiring - Internal wiring is routed away from sharp or moving parts. Internal wiring leads terminating
in soldered connections are made mechanically secure prior to soldering. Recognized Component
Critical Features/Components - An essential part, material, subassembly, system, software, or accessory of a
product that has a direct bearing on the product’s conformance to applicable requirements of the product
standard.
Construction Details - For specific construction details, reference should be made to the photographs and
descriptions. All dimensions are approximate unless specified as exact or within a tolerance. In addition to the
specific construction details described in this Report, the following general requirements also apply.
Recognized Component - A component part, which has been previously evaluated by an accredited certification
body with restrictions and must be evaluated as part of the basic product considering the restrictions as specified
by the Conditions of Acceptability.
6.0 Critical Features
Unlisted Component - A part that has not been previously evaluated to the appropriate designated component
standard. It may also be a Listed or Recognized component that is being used outside of its evaluated Listing or
component recognition.
1. Spacing -Spacings do not apply since the circuit is in Class 2.
Listed Component - A component part, which has been previously Listed or Certified by an accredited
Certification Organization with no restrictions and is used in the intended application within its ratings.
in soldered connections are made mechanically secure prior to soldering. Recognized Component
separable (quick disconnect) connectors of the positive detent type, closed loop connectors, or other types
specifically described in the text of this report are also acceptable as internal wiring terminals. At points
where internal wiring passes through metal walls or partitions, the wiring insulation is protected against
abrasion or damage by plastic bushings or grommets. All wiring is minimum 24 AWG, with a minimum rating
of 150V, 90°C, not subject to movement under normal use and in Class 2 secondary.
7. Schematics - No schematics requiring verification during Field Representative Inspection Audits.
8. Markings - The product is marked on a labeling system as described in item no. 1 of Section 4.0 as follows:
manufacturer's name, model number, date of manufacture, electrical ratings - Format A1
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 9 of 16 Issued: 2-Oct-2012
Revised: None
6.0 Critical Features
9. Cautionary Markings - The following are required:
Model Marking Items
ALL 1,2,3
Item Text Format
1 INSTALLATION OR ASSEMBLY INSTRUCTIONS (NO TRANSLATION APPLICABLE)
C
2 DRY LOCATIONS ONLY POUR EMPLACEMENTS SECS SEULEMENT
Verbatim B3
3 USE ONLY WITH CLASS 2 POWER UNIT UTILISER SEULEMENT AVEC LA CLASSE 2 UNITE D'ALIMENTATION ELECTRIQUE
A3
Form designation for type of marking
Form letter of marking Type
A Permanent – Paint-stenciled, die-stamped, indelibly printed lettering, or indelibly printed pressure sensitive label.
a
B Temporary – Pressure-sensitive label, decalcomania transfer, paper label, paint, ink, or die stamped lettering.
b
C Instructions – Tie-on tag, stuffer sheet or equivalentc
a Pressure sensitive labels shall comply with the requirements in the Standard for Marking and Labeling
Systems, UL 969. b Form A markings are also able to be used.
c Forms A and B markings are also able to be used.
Form designations for locations of markings
Form number of marking Location of markings
1 Visible after installation
2 Visible during relamping
3 Visible during installation
4 On the smallest unit packaging carton
Form designations for location of marking
For no. of marking
Location of marking
1 On an exterior surface that is normally visible. Marking is determined to be normally visible
10. Installation, Operating and Safety Instructions - Instructions for installation and use of this product are
provided by the manufacturer.
marking Location of marking
1 On an exterior surface that is normally visible. Marking is determined to be normally visible when a lamp or glassware is required to be removed to make the marking visible.
2 Adjacent to the ballast and readily visible before and during ballast replacement.
3 At a point where visible during relamping.
4 On the smallest unit packaging carton.
5 At a point visible during mounting.
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 10 of 16 Issued: 2-Oct-2012
Revised: None
Illustration 1 - Model Ratings
Model
Size
Nominal
Input
Voltage
Max Input
Power
(W)
Channel
Width (in)
Channel
Height
(in)
Volume
(cu.
inches)
Power /
Volume
Weight
(lbs)
3 foot 24VDC 86.4 1.25 9 2501 0.004 28.5
5 foot 24VDC 172.8 1.6 12 7142 0.002 36.0
7 foot 24VDC 288.0 2 15 15645 0.001 61.0
Illustration 2 - LED Strip Details.
Strip # Hoop Size Color Temp # of LEDs # of Strings
Radius of
Curvature
[in]
Strip Length
[in]
Nominal LED
Pitch [in]
1 3' 3200K 21 3 17.38 26.79 1.28
2 5' 3200K 21 3 29.20 22.43 1.07
3 7' 3200K 35 5 41.00 31.70 0.91
4 9' 3200K 21 3 52.88 18.34 0.87
5 3' 4250K 21 3 17.38 26.79 1.28
6 5' 4250K 21 3 29.20 22.43 1.07
7 7' 4250K 35 5 41.00 31.70 0.91
8 9' 4250K 21 3 52.88 18.34 0.87
7.0 Illustrations
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 11 of 16 Issued: 2-Oct-2012
Revised: None
Evaluation Period Project No. G100739742
Sample Rec. Date 5/3/2012 Condition Prototype Sample ID. #3
Test Location
Test Procedure
ANSI/UL 2108
Clause
CAN/CSA
C22.2 No.
250.0-08
Clause
ANSI/UL 8750
Clause
59 14 8.3
62A 16.15
Completed by: Reviewed by:
Title: Title:
Signature: Signature:
Project Engineer
Normal Temperature
Mounting Means
A representative sample of the product covered by this report has been evaluated and found to comply with the
applicable requirements of the standards indicated in Section 1.0.
8.1 Signatures
Emil P. Remolana
Review Engineer
Carl Bloomfield
8.0 Test Summary
3M SEMS Product Safety Laboratory, 3M Center Building 235-BE-03, Maplewood, MN
55144-1000 USA
Supervised Applicant Testing
Test Description
05/03/12 - 10/02/12
Determination of the result includes consideration of measurement uncertainty from the test equipment and
methods. The product was tested as indicated below with results in conformance to the relevant test criteria.
These products were also evaluated to the Standard for Safety for Light Emitting Diode (LED) Equipment for use
in Lighting Products, (UL 8750, 1st Ed., revised 11/01/11) and Standard for Safety for Light Emitting Diode (LED)
Equipment for Lighting Applications, (CAN/CSA C22.2#250.13, 1st Ed., dated 01/01/12).
The following tests were performed:
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 12 of 16 Issued: 2-Oct-2012
Revised: None
BASIC LISTEE
Address
Country
Product
MULTIPLE LISTEE 1
Address
Country
Brand Name
ASSOCIATED
MANUFACTURER
Address
Country
BASIC LISTEE MODELS
MULTIPLE LISTEE 2
Address
Country
Brand Name
ASSOCIATED
MANUFACTURER
Address
Country
BASIC LISTEE MODELS
MULTIPLE LISTEE 3
Address
Country
Brand Name
ASSOCIATED
MANUFACTURER
Address
Country
BASIC LISTEE MODELS
MULTIPLE LISTEE 1 MODELS
None
MULTIPLE LISTEE 3 MODELS
None
MULTIPLE LISTEE 2 MODELS
None
USA
9.0 Correlation Page For Multiple Listings
The following products, which are identical to those identified in this report except for model number and Listee
name, are authorized to bear the ETL label under provisions of the Intertek Multiple Listing Program.
3M Company
Building 223-5S-01
St. Paul, MN 55144
Low Voltage Luminaire
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 13 of 16 Issued: 2-Oct-2012
Revised: None
10.0 General Information
The Applicant and Manufacturer have agreed to produce, test and label ETL Listed products in accordance with
the requirements of this Report. The Manufacturer has also agreed to notify Intertek and to request authorization
prior to using alternate parts, components or materials.
COMPONENTS
Components used shall be those itemized in this Intertek report covering the product, including any amendments
and/or revisions.
LISTING MARK
The ETL Listing mark applied to the products shall either be separable in form, such as labels purchased from
Intertek, or on a product nameplate or other media only as specifically authorized by Intertek. Use of the mark is
subject to the control of Intertek.
The mark must include the following four items:
1) applicable country identifiers "US" and/or "C" or "US", "C" and "EU"
2) the word "Listed" or "Classified" or "Recognized Component" (whichever is appropriate)
3) a control number issued by Intertek
4) a product descriptor that identifies the standards used for certification. Example:
For US standards, the words, “Conforms to” shall appear with the standard number along with the word,
“Standard” or “Std.” Example: “Conforms to ANSI/UL Std. XX.”
For Canadian standards, the words “Certified to CAN/CSA Standard CXX No. XX.” shall be used, or
abbreviated, “Cert. to CAN/CSA Std. CXX No. XX.”
Can be used together when both standards are used.
Note: A facsimile must be submitted to Intertek, Attn: Follow-up Services for approval prior to use.
The facsimile need not have a control number. A control number will be issued after signed Certification
Agreements have been received by the Follow-up Services office, approval of the facsimile of your
proposed Listing Mark, satisfactory completion of the Listing Report, and scheduling of a factory
assessment in your facility.
MANUFACTURING AND PRODUCTION TESTS
Manufacturing and Production Tests shall be performed as required in this Report.
FOLLOW-UP SERVICE
Periodic unannounced audits of the manufacturing facility (and any locations authorized to apply the mark) shall
be scheduled by Intertek. An audit report shall be issued after each visit. Special attention will be given to the
following:
1. Conformance of the manufactured product to the descriptions in this Report.
2. Conformance of the use of the ETL mark with the requirements of this Report and the Certification Agreement.
3. Manufacturing changes.
4. Performance of specified Manufacturing and Production Tests.
In the event that the Intertek representative identifies non-conformance(s) to any provision of this Report, the
Applicant shall take one or more of the following actions:
1. Correct the non-conformance.
2. Remove the ETL Mark from non-conforming product.
3. Contact the issuing product safety evaluation center for instructions.
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 14 of 16 Issued: 2-Oct-2012
Revised: None
10.1 Evaluation of Unlisted Components
Note to Intertek Follow Up Inspector: The Component Evaluation Center, CEC, will notify you in writing
when these components must be selected and sent to the CEC for re-evaluation
Ship the samples to:
Intertek Testing Services NA Inc.
ETL Component Evaluation Center
13200 Levan Road
Livonia, MI 48150 USA
Attn: Component Evaluation Center
Sample Disposition: Due to the destructive nature of the testing, all samples will be
discarded at the conclusion of testing unless, the manufacturer specifically requests the
return of the samples. The request for return must accompany the initial component
Because Unlisted Components are uncontrolled, and they do not fall under a third party follow up program,
Intertek may require these components to be tested and/or evaluated at least once annually, more often for
certain components, as part of the independent certification process. The Unlisted Components in Section 5.0
require testing and/or evaluation as indicated.
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 15 of 16 Issued: 2-Oct-2012
Revised: None
None.
11.0 Manufacturing and Production Tests
The manufacturer agrees to conduct the following Manufacturing and Production Tests as specified:
Required Tests
ED 16.3.15 (18-Jun-12) Mandatory
Report No. 100739742CHI-001
3M CompanyPage 16 of 16 Issued: 2-Oct-2012
Revised: None
Date/ Project Handler/
Proj # Site ID Reviewer
None
12.0 Revision Summary
The following changes are in compliance with the declaration of Section 8.1:
Section Item Description of Change
ED 16.3.15 (18-Jun-12) Mandatory