Liquid Ring Vacuum Pumps Close-coupled Version Flüssigkeitsring ...
Transcript of Liquid Ring Vacuum Pumps Close-coupled Version Flüssigkeitsring ...
Liquid Ring Vacuum PumpsClose-coupled Version
Flüssigkeitsring-Vakuumpumpen Blockbauweise
2
VI / V / VG / VN / VZLiquid ring vacuum pumpsClose-coupled version
V Series The all-rounders• Single-stage• With valve flaps• With mechanical seal• 33 - 40 mbar
VI SeriesWater savers with internal water restraining system• Single-stage• With internal water restraining system• In inverted design• With valve flaps• With mechanical seal• 33 - 45 mbar
VG SeriesValveless and low-maintenance• Single-stage• Without valves• Without dead spots• With mechanical seal• VG 95 up to VG 255:
thread execution or flange execution• 40 - 70 mbar
VN SeriesFor large quantities of additional liquid• Single-stage• With valve flaps• With port cylinder• With mechanical seal• Up to 10 m³/h water delivery• 55 mbar
VZ SeriesRobust and low-noise technology for deep vacuum ranges• Double-stage• Without valves• In close-coupled and base plate version1)
• With mechanical seal and magnetic coupling2)
• 33 mbar
1) See brochure Liquid ring vacuum pumps – base plate version: VZ 110G / 140G / 180G
2) On request
Flüssigkeitsring-Vakuumpumpen Blockbauweise
Baureihe VIDie Wassersparer mit internem Wasserrückhaltesystem• Einstufig• Mit internem Wasserrückhaltesystem• In invertierter Bauweise• Mit Ventilklappen • Mit Gleitringdichtung• 33 - 45 mbar
Baureihe VDie Allrounder• Einstufig• Mit Ventilklappen• Mit Gleitringdichtung• 33 - 40 mbar
Baureihe VGVentillos und wartungsarm• Einstufig• Ohne Ventile• Ohne Totraum• Mit Gleitringdichtung• VG 95 bis VG 255 in
Flansch- oder Gewindeausführung• 40 - 70 mbar
Baureihe VNFür große Mengen zusätzlicher Flüssigkeit• Einstufig• Mit Ventilklappen• Mit Nabensteuerung • Mit Gleitringdichtung• Bis zu 10 m³/h Wassermitförderung• 55 mbar
Baureihe VZRobuste und geräuscharme Technik für tieferes Vakuum• Zweistufig• Ohne Ventile• In Block- und Grundplattenbauweise1)
• Mit Gleitringdichtung und Magnetkupplung2)
• 33 mbar
1) Siehe Prospekt Flüssigkeitsring-Vakuumpumpen – Grundplattenbauweise: VZ 110G / 140G / 180G
2) Auf Anfrage
3
VI / V / VG / VN / VZ
Subject to technical modifications and error.
Your AdvantageHigh reliability• Simple working principle• Robust construction• Use of high-quality materials• Low-temperature compression
Favourable maintenance• Use of few components• O-ring sealing
Cost effective• Close-coupled version• Customized construction• Long life-time
Liquid ring vacuum pumpsClose-coupled version
Technische Änderungen und Irrtum vorbehalten.
Ihr NutzenHohe Zuverlässigkeit• Einfaches Wirkungsprinzip• Robuster Aufbau• Einsatz hochwertiger Materialien• Verdichtung bei geringen Temperaturen
Servicefreundlich• Einsatz nur weniger Bauteile• O-Ring Abdichtung
Kostengünstig• Blockausführung• Anwendungsspezifische Konstruktion• Lange Lebensdauer
Flüssigkeitsring-Vakuumpumpen Blockbauweise
Technische Daten / Technical data50 Hz/cycles 60 Hz/cycles Schall-
druck- pegel1
Sound pressure level1
Typ
Type
Drehzahl
Motor speed
Leistung
Motor rating
max. Saugvermögen
max. suction capacity
Drehzahl
Motor speed
Leistung
Motor rating
max. Saugvermögen
max. suction capacity
min. Ansaugdruck
min. inlet pressure
Seiten
Pages
1 / min kW HP m³/h CFM rpm kW HP m³/h CFM mbar inch Hg a db(A)VI-2 2850 0,12 0.16 2,2 1,3 3450 0,18 0.24 2,4 1,4 45 1.3 65 4, 5, 32
VI-8 2850 0,4 0.5 9,5 5,6 3450 0,5 0.7 11,4 6,7 40 1.2 65 6, 7, 32
VI-18 2850 0,75 1.0 18 10,6 3450 1,1 1.5 21 12,4 40 1.2 688, 9, 32
VI-25 2850 0,75 1.0 24 14,1 3450 1,1 1.5 27 15,9 40 1.2 68
VI-30 2850 1,1 1.5 27 16 3450 1,5 2.0 33 19 33 1.0 6810, 11, 32
VI-55 2850 1,5 2.0 46 27 3450 2,2 3.0 55 32 33 1.0 68
V-6 2850 0,4 0.5 9,5 5,6 3450 0,5 0.7 11,4 6,7 40 1.2 68 12, 13, 32
V-30 2850 1,1 1.5 26 15 3450 1,5 2.0 31 18 33 1.0 6814, 15, 32
V-55 2850 1,5 2.0 48 28 3450 2,2 3.0 57 33 33 1.0 69
V-95 1450 2,2 3.0 70 41 1750 3,0 4.0 81 48 33 1.0 65
16, 17, 32V-130 1450 3,0 4.0 100 59 1750 4,6 6.2 122 72 33 1.0 65
V-155 1450 4,0 5.4 123 72 1750 6,2 8.3 146 86 33 1.0 65
V-255 1450 5,5 7.4 199 117 1750 8,2 11.0 244 144 33 1.0 65
V-330 1450 7,5 10 265 156 1750 13 18 318 187 33 1.0 7218, 19, 32
V-430 1450 11,0 15 370 218 1750 18 24 445 262 33 1.0 72
VG-30 2850 1,1 1.5 26 15 3450 1,5 2.0 34 20 70 2.1 6820, 21, 33
VG-55 2850 1,5 2.0 48 28 3450 2,2 3.0 56 33 70 2.1 68
VG-95 1450 2,2 3.0 70 41 1750 3,0 4.0 81 48 55 1.6 68
22 - 25, 33VG-130 1450 3,0 4.0 100 59 1750 4,6 6.2 123 72 55 1.6 68
VG-155 1450 4,0 5.4 123 72 1750 6,2 8.3 146 86 40 1.2 65VG-255 1450 5,5 7.4 203 119 1750 8,2 11.0 245 144 40 1.2 65
VN-95 1450 3,0 4.0 95 56 1750 4,6 (4,4*) 6.2 (5.9*) 144 85 55 1.6 6526, 27, 33VN-125 1450 4,3 5.8 126 74 1750 6,6 (6,3*) 8.9 (8.4*) 151 89 55 1.6 65
VN-180 1450 5,5 7.4 180 106 1750 8,2 11.0 216 127 55 1.6 65
VZ-30 2850 1,1 1.5 30 18 3450 1,5 2.0 34 20 33 1.0 6028, 29, 34
VZ-50 2850 1,5 2.0 49 29 3450 2,2 3.0 59 34 33 1.0 60
VZ-110 1450 3,0 4.0 107 63 1750 4,0 5.4 128 75 33 1.0 66
30, 31, 34VZ-140 1450 4,0 5.4 145 85 1750 5,5 7.4 174 102 33 1.0 66
VZ-180 1450 5,5 7.4 186 109 1750 8,2 11.0 223 131 33 1.0 66
1) Bei 80 mbar / 2.4 inch Hg a* IE2-Motor
1) At 80 mbar / 2.4 inch Hg a* IE2 motors / subtype 2
06/2015 | 1096.0911
4
VI-2 II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - with internal water restraining system
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - mit internem Wasserrückhaltesystem
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUC Kavitationsschutz Cavitation protectionUL Anschluss für Belüftungsventil Vacuum relief valve connectionUS Anschluss für Sensor Connection for sensor
Teileliste / Part list047 Gleitringdichtung Mechanical seal137 Steuerscheibe Inter casing161 Gehäusedeckel Casing cover230 Laufrad Impeller411/.1 Dichtring Sealing ring412 O-Ring O-ring441 Gehäuse für Wellendichtung Shaft seal casing561 Kerbstift Grooved pin800 Motor Motor903/.1 Verschlussschraube Screw plug914 Innen-6-kt. Schraube Hexagon socket head screw932 Sicherungsring Locking ring940 Passfeder Fitting key
Daten / Data50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UC UL USVI-2 56 2850 0,12 0.16 3450 0,18 0.24 5,4 12 G 1/8 G 1/8 G 1/8 M8
BG = Baugröße FS = Frame size
Schnittzeichnung / Sectional drawing
Maßzeichnung / Dimensional drawing
06/2015 | 1096.0911
5
33 40 60 80 100 200 300 400 600 900 33 40 60 80 100 200 300 400 600 900
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
1,5
1,0
0,5
0
4
3
2
1
0
2,5
2,0
1,5
1,0
0,5
0 0,25
0,20
0,15
0,10
0,05
0
0.30
0.25
0.20
0.15
0.10
0.05
0
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
VI-2
50 Hz-cycles | 2850 1/min - rpm 60 Hz-cycles | 3450 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - with internal water restraining system
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - mit internem Wasserrückhaltesystem
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
6
G3/8
Ø 7
637
151
44 80100
189250
UC
US
Ue
UB
UL
46
100120
118
VI-8 II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - with with valve flaps and internal water restraining system
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen und internem Wasserrückhaltesystem
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUC Kavitationsschutz Cavitation protectionUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connectionUS Anschluss für Sensor Connection for sensor
Teileliste / Part list047 Gleitringdichtung Mechanical seal137 Steuerscheibe Inter casing161 Gehäusedeckel Casing cover230 Laufrad Impeller411/.1 Dichtring Sealing ring412 O-Ring O-ring441 Gehäuse für Wellendichtung Shaft seal casing561 Kerbstift Grooved pin746 Ventilklappe Valve flap746.1 Ventilklappenunterlage Valve flap pad800 Motor Motor901 6-kt. Schraube Hexagon head screw903/.1 Verschlussschraube Screw plug932 Sicherungsring Locking ring940 Passfeder Fitting key
Daten / Data50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UC Ue UL USVI-8 63 2850 0,4 0.5 3450 0,5 0.7 9,2 20 G 1/8 G 1/8 G 1/8 G 1/8 ø 3,2
BG = Baugröße FS = Frame size
Schnittzeichnung / Sectional drawing
Maßzeichnung / Dimensional drawing
06/2015 | 1096.0911
7
VI-8
33 40 60 80 100 200 300 400 600 900 33 40 60 80 100 200 300 400 600 900
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
0.5
0.4
0.3
0.2
0.1
0 2,0
1,5
1,0
0,5
0
12
10
8
6
4
2
0 0,4
0,3
0,2
0,1
0
7
6
5
4
3
2
1
0
0.5
0.4
0.3
0.2
0.1
0
50 Hz-cycles | 2850 1/min - rpm 60 Hz-cycles | 3450 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - with valve flaps and internal water restraining system
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen und internem Wasserrückhaltesystem
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
8
VI-18 / 25
173*
71
110
9
213*
47,58
90
G 1/2"
112138
133
137
14
U
U
Ue
C
L
BU
Um
50
z*
178*
412 903161 137
230
551
932
047
940
561
746746.1
914
800
903.1411.1411
441
II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - with valve flaps and internal water restraining system
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen und internem Wasserrückhaltesystem
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUC Kavitationsschutz Cavitation protectionUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connectionUm Anschluss für Manometer Pressure gauge connection
Teileliste / Part list047 Gleitringdichtung Mechanical seal137 Steuerscheibe Inter casing161 Gehäusedeckel Casing cover230 Laufrad Impeller411/.1 Dichtring Sealing ring412 O-Ring O-ring441 Gehäuse für Wellendichtung Shaft seal casing551 Abstandsscheibe Washer561 Kerbstift Grooved pin746 Ventilklappe Valve flap746.1 Ventilklappenunterlage Valve flap pad800 Motor Motor903/.1 Verschlussschraube Screw plug914 Innen-6-kt. Schraube Hexagon socket head screw932 Sicherungsring Locking ring940 Passfeder Fitting key
Daten / Data50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UC Ue UL UmVI-18 71 2850 0,75 1.0 3450 1,1 1.5 13 39 G 1/8 G 1/8 G 1/8 G 1/8 G 3/8VI-25 2850 0,75 1.0 3450 1,1 1.5 14 41
Type BG/FS z*VI-18 71 284VI-25 294
BG = Baugröße, gilt für IE1 und IE2-Motoren* Abhängig von der Ausführung des Motors
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2)* Depending on the motor design
06/2015 | 1096.0911
9
VI-18 / 25
009 006 004 003 002 001 08 06 04 33 009 006 004 003 002 001 08 06 04 33
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
3
2
1
0
0.8
0.6
0.4
0.2
0
30
25
20
15
10
5
01,0
0,8
0,6
0,4
0,2
0
1.2
1.0
0.8
0.6
0.4
0.2
0
17.5
15.0
12.5
10.0
7.5
5.0
2.5
0
VI-25
VI-18
VI-25
VI-18
VI-25
VI-18
VI-25
VI-18
VI-18
VI-25VI-25
VI-18
50 Hz-cycles | 2850 1/min - rpm 60 Hz-cycles | 3450 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - with valve flaps and internal water restraining system
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen und internem Wasserrückhaltesystem
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
10
**
*
Z3*
VI-30 / 55 II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - with valve flaps and internal water restraining system
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen und internem Wasserrückhaltesystem
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUC Kavitationsschutz Cavitation protectionUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connectionUm Anschluss für Manometer Pressure gauge connection
Teileliste / Part list047 Gleitringdichtung Mechanical seal137 Steuerscheibe Inter casing161 Gehäusedeckel Casing cover230 Laufrad Impeller411-.2 Dichtring Sealing ring412 O-Ring O-ring441 Gehäuse für Wellendichtung Shaft seal casing550 Scheibe Washer561 Kerbstift Grooved pin746 Ventilklappe Valve flap800 Motor Motor901 6-kt. Schraube Hexagon head screw903-.2 Verschlussschraube Screw plug932 Sicherungsring Locking ring940 Passfeder Fitting key
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing
Daten und Maße / Data and dimensions50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UC Ue UL UmVI-30 80 2850 1,1 1.5 3450 1,5 2.0 18 40 G 1/4 G 1/4 G 1/4 G 1/4 G 1/2VI-55 90 2850 1,5 2.0 3450 2,2 3.0 26 57
Type BG/FS h3 w z* z2* A AB BB H HA HD* Z3*VI-30 80 161 60 328 251 126 152 100 80 12 196 206VI-55 90 171 64 385 288 140 171 125 90 13 210 242,5
BG = Baugröße, gilt für IE1 und IE2-Motoren* Abhängig von der Ausführung des Motors
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2)* Depending on the motor design
06/2015 | 1096.0911
11
VI-30 / 55
33 40 60 80 100 200 300 400 600 900 33 40 60 80 100 200 300 400 600 900
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
6543210
1.6
1.2
0.8
0.4
0
60
55
50
45
40
35
30
25
20
15
10
5
02,50
2,25
2,00
1,75
1,50
1,25
1,00
0,75
0,50
0,25
0
3.0
2.5
2.0
1.5
1.0
0.5
0
35
30
25
20
15
10
5
0
VI 55
VI 30
VI 55
VI 30
VI 55
VI 30
VI 55
VI 55
VI 30
VI 30
VI 55
VI 30
50 Hz-cycles | 2850 1/min - rpm 60 Hz-cycles | 3450 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - with valve flaps and internal water restraining system
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen und internem Wasserrückhaltesystem
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
12
V-6 II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - with valve flaps
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUC Kavitationsschutz Cavitation protectionUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connection
Teileliste / Part list047 Gleitringdichtung Mechanical seal101 Pumpengehäuse Pump casing137 Steuerscheibe Inter casing230 Laufrad Impeller411/.1 Dichtring Sealing ring412/.1 O-Ring O-ring441 Gehäuse für Wellendichtung Shaft seal casing561 Kerbstift Grooved pin746 Ventilklappe Valve flap800 Motor Motor903/.1 Verschlussschraube Screw plug914/.1 Innen-6-kt. Schraube Hexagon socket head screw932 Sicherungsring Locking ring940 Passfeder Fitting key
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing
Daten / Data50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UC Ue ULV-6 63 2850 0,4 0.5 3450 0,5 0.7 9,3 21 G 1/8 G 1/8 M5 G 1/8
BG = Baugröße FS = Frame size
06/2015 | 1096.0911
13
V-6
33 40 60 80 100 200 300 400 600 900 33 40 60 80 100 200 300 400 600 900
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
3
2
1
0
12
10
8
6
4
2
0 0,4
0,3
0,2
0,1
0
0.5
0.4
0.3
0.2
0.1
0
7
6
5
4
3
2
1
0
0.8
0.6
0.4
0.2
0
50 Hz-cycles | 2850 1/min - rpm 60 Hz-cycles | 3450 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - with valve flaps
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
14
**
*
*
V-30 / 55 II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - with valve flaps
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUC Kavitationsschutz Cavitation protectionUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connectionUV Anschluss für Entleerungsventil Connection for drainage valve
Teileliste / Part list047 Gleitringdichtung Mechanical seal101 Pumpengehäuse Pump casing137 Steuerscheibe Inter casing230 Laufrad Impeller411/.1 Dichtring Sealing ring441 Gehäuse für Wellendichtung Shaft seal casing550/.1/.3 Scheibe Washer561/.1 Kerbstift Grooved pin598 Blech Sheet746 Ventilklappe Valve flap800 Motor Motor901/.1 6-kt. Schraube Hexagon head screw902 Stiftschraube Stud903/.1 Verschlussschraube Screw plug906 Laufradschraube Impeller screw920/.1 6-kt. Mutter Hexagon nut950 Tellerfeder Washer spring970 Typenschild Name plate
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing
Daten und Maße / Data and dimensions50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UC Ue UL UVV-30 80 2850 1,1 1.5 3450 1,5 2.0 20 44 G 1/4 G 1/8 G 1/4 G 1/4 G1/4V-55 90 2850 1,5 2.0 3450 2,2 3.0 25 55
Type BG/FS h3 u1 u2 q w z* z2* A AB B BB C H HA HD*V-30 80 158 7 104 70 152 391 357 125 153 100 125 50 80 10 231V-55 90 171 5 110 74 176 409 375 140 170 125 155 56 90 11 240
BG = Baugröße, gilt für IE1 und IE2-Motoren* Abhängig von der Ausführung des Motors
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2)* Depending on the motor design
06/2015 | 1096.0911
15
V-30 / 55
009 006 004 003 002 001 08 06 04 33 009 006 004 003 002 001 08 06 04 33
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
6
4
2
0
1.6
1.2
0.8
0.4
0
60
50
40
30
20
10
0 2,5
2,0
1,5
1,0
0,5
0
3.0
2.5
2.0
1.5
1.0
0.5
0
35
30
25
20
15
10
5
0
V-55
V-30
V-55
V-30
V-55
V-30
V-55
V-55
V-30
V-30
V-55
V-30
50 Hz-cycles | 2850 1/min - rpm 60 Hz-cycles | 3450 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - with valve flaps
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
16
z2*z*
LB*
HD*
ULUL
ØD1DN ØD2
Ø18q
h4u2 h3
AAB
u1
UV UVUe Ue
UeUe
UC
UC
UBUB
BC
wBB
Ø12
HAH
V-95 / 130 / 155 V-255
V-95 / 130 / 155 / 255 II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - with valve flaps
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUC Kavitationsschutz Cavitation protectionUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connectionUV Anschluss für Entleerungsventil Connection for drainage valve
Teileliste / Part list047 Gleitringdichtung Mechanical seal101 Pumpengehäuse Pump casing137 Steuerscheibe Inter casing230 Laufrad Impeller411/.1 Dichtring Sealing ring412 O-Ring O-ring441 Gehäuse für Wellendichtung Shaft seal casing550/.1 Scheibe Washer561/.1 Kerbstift Grooved pin598 Blech Sheet746 Ventilklappe Valve flap800 Motor Motor900 Schraube Screw901/.1/.3 6-kt. Schraube Hexagon head screw903/.1 Verschlussschraube Screw plug906 Laufradschraube Impeller screw920/ .1 6-kt. Mutter Hexagon nut950 Tellerfeder Washer spring970 Typenschild Name plate
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing
Daten und Maße / Data and dimensions50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UC Ue UL UV DN D1 D2V-95 100L 1450 2,2 3.0 1750 3,0 4.0 59 130
110V-130 100L 1450 3,0 4.0 1750 4,6 6.2 67 148 G 1/2 G 3/8 G 3/8 G 1/2 G 3/8 40 150V-155 112M 1450 4,0 5.4 1750 6,2 8.3 83 183V-255 132S 1450 5,5 7.4 – – – 111 245 G 1/2 G 1/2 G 1/2 G 1/2 G 1/2 50 165 125132M – – – 1750 8,2 11.0
Type BG/FS h3 h4 u1 u2 q w z* z2* A AB B BB C H HA HD* LB*V-95 100L 275 328 63 278 180 192 507 432 160 195 140 176 63 100 13 255 303V-130 100L 275 328 63 278 180 201 516 441 160 195 140 176 63 100 13 255 303V-155 112M 287 328 63 278 180 225 550 475 190 225 140 176 70 112 15 280 320V-255 132S 312 370 60 295 200 290 689 606 216 256 140 218 110 132 18 320 426132M 178
BG = Baugröße, gilt für IE1 und IE2-Motoren, * Abhängig von der Ausführung des MotorsFlanschanschlussmaße nach EN 1092-2 PN 10, Ausführung nach ANSI auf Anfrage
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2), * Depending on the motor designFlanges dimensions in acc. with EN 1092-2 PN 10, execution in acc. with ANSI standards on request
06/2015 | 1096.0911
17
V-95 / 130 / 155 / 255
009 006 004 003 002 001 08 06 04 33 009 006 004 003 002 001 08 06 04 33
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
25
20
15
10
5
0
6
4
2
0
260
240
220
200
180
160
140
120
100
80
60
40
20
0 8
7
6
5
4
3
2
1
0
10
8
6
4
2
0
140
120
100
80
60
40
20
0
V-255
V-95
V-130
V-155
V-255
V-95
V-130
V-95 - 155
V-255
V-95 - 155
V-255
V-155
V-255
V-95
V-130
V-155
V-255
V-95
V-130
V-155
50 Hz-cycles | 1450 1/min - rpm 60 Hz-cycles | 1750 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - with valve flaps
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
18
**
*
*
V-330 / 430 II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - with valve flaps
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUC Kavitationsschutz Cavitation protectionUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connectionUV Anschluss für Entleerungsventil Connection for drainage valve
Teileliste / Part list047 Gleitringdichtung Mechanical seal101 Pumpengehäuse Pump casing137 Steuerscheibe Inter casing230 Laufrad Impeller400 Flachdichtung Flat gasket411 Dichtring Sealing ring412 O-Ring O-ring441 Gehäuse für Wellendichtung Shaft seal casing550/.1 Scheibe Washer561/.1 Kerbstift Grooved pin598 Blech Sheet723 Gewindeflansch Flange746 Ventilklappe Valve flap800 Motor Motor900 Schraube Screw901-.3 6-kt. Schraube Hexagon head screw902 Stiftschraube Stud903./2 Verschlussschraube Screw plug904 Gewindestift Set screw906 Laufradschraube Impeller screw920/.1 6-kt. Mutter Hexagon nut931 Sicherungsblech Locking washer950 Druckfeder Pressure spring970 Typenschild Name plate
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing
Daten und Maße / Data and dimensions50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UC Ue UL UV
V-330 132M 1450 7,5 10.1 – – – 122 269
G 1 G 1/2 G 1/2 G 1/2 G 1/2160M – – – 1750 13,2 17.7 163 359V-430 160M 1450 11,0 14.8 – – – 155 342
160L – – – 1750 18,0 24.1 178 392
Type BG/FS h3 w z* z2* A AB B BB C H HA HD* K LB*V-330 132M 353 303 732 639 216 256 178 218 95 132 18 320 12 431
160M 361 311 813 720 254 320 210 260 103 160 22 410 14 512V-430 160M 361 324 826 733 254 320 210 260 103 160 22 410 14 512160L 254 304
BG = Baugröße, gilt für IE1 und IE2-Motoren* Abhängig von der Ausführung des MotorsFlanschanschlussmaße nach EN 1092-2 PN 10, Ausführung nach ANSI auf Anfrage
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2)* Depending on the motor designFlanges dimensions in acc. with EN 1092-2 PN 10, execution in acc. with ANSI standards on request
06/2015 | 1096.0911
19
V-330 / 430
009 006 004 003 002 001 08 06 04 33 009 006 004 003 002 001 08 06 04 33
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
40
30
20
10
0
500
450
400
350
300
250
200
150
100
50
0 16
14
12
10
8
6
4
2
0
20
18
16
14
12
10
8
6
4
2
0
280
240
200
160
120
80
40
0
10
8
6
4
2
0
V-430
V-330
V-430
V-330
V-430
V-330
V-430
V-330
V-430
V-330
V-430
V-330
50 Hz-cycles | 1450 1/min - rpm 60 Hz-cycles | 1750 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - with valve flaps
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
20
**
*
*
VG-30 / 55 II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - without valves
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - ohne Ventile
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUe Entleerung Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connection
Teileliste / Part list047 Gleitringdichtung Mechanical seal161 Gehäusedeckel Casing cover230 Laufrad Impeller411 Dichtring Sealing ring441 Gehäuse für Wellendichtung Shaft seal casing550/.1 Scheibe Washer561/.1 Kerbstift Grooved pin800 Motor Motor901 6-kt. Schraube Hexagon head screw902 Stiftschraube Stud903 Verschlussschraube Screw plug906 Laufradschraube Impeller screw920/.1 6-kt. Mutter Hexagon nut950 Tellerfeder Washer spring970 Typenschild Name plate
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing
Daten und Maße / Data and dimensions50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB Ue ULVG-30 80 2850 1,1 1.5 3450 1,5 2.0 18 40 G 1/4 G 1/4 G 1/4VG-55 90 2850 1,5 2.0 3450 2,2 3.0 22 49
Type BG/FS h3 u2 q w z* z2* A AB BB C H HA HD*VG-30 80 158 78 70 146 375 351 125 153 125 50 80 10 231VG-55 90 171 81 74 168 391 367 140 170 155 56 90 11 240
BG = Baugröße, gilt für IE1 und IE2-Motoren* Abhängig von der Ausführung des Motors
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2)* Depending on the motor design
06/2015 | 1096.0911
21
VG-30 / 55
009 006 004 003 002 001 08 06 04 33 009 006 004 003 002 001 08 06 04 33
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
3.0
2.5
2.0
1.5
1.0
0.5
0 4
3
2
1
0
1.0
0.8
0.6
0.4
0.2
0
60
50
40
30
20
10
0 2,5
2,0
1,5
1,0
0,5
0
35
30
25
20
15
10
5
0
VG-55
VG-30
VG-55
VG-30
VG-55
VG-30
VG-30 / 55 VG-30 / 55
VG-55
VG-30
50 Hz-cycles | 2850 1/min - rpm 60 Hz-cycles | 3450 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - without valves
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - ohne Ventile
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
22
**
*
*
II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - without valves
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - ohne Ventile
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connection
Teileliste / Part list047 Gleitringdichtung Mechanical seal161 Gehäusedeckel Casing cover230 Laufrad Impeller411/.1 Dichtring Sealing ring412 O-Ring O-ring441 Gehäuse für Wellendichtung Shaft seal casing550-.1 Scheibe Washer561 Kerbstift Grooved pin800 Motor Motor901/.1 6-kt. Schraube Hexagon head screw903/.1 Verschlussschraube Screw plug906 Laufradschraube Impeller screw920/.1 6-kt. Mutter Hexagon nut950 Tellerfeder Washer spring970 Typenschild Name plate
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing
VG-95 / 130 / 155 / 255 – Gewindeausführung | Thread execution
Daten und Maße / Data and dimensions50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB Ue UL GVG-95 100L 1450 2,2 3.0 1750 3,0 4.0 52 115VG-130 100L 1450 3,0 4.0 1750 4,6 6.2 59 130 G 1/2 G 3/8 G 1/2 G 1 1/2VG-155 112M 1450 4,0 5.4 1750 6,2 8.3 67 148VG-255 132S 1450 5,5 7.4 – – – 105 231 G 1/2 G 1/2 G 1/2 G 2132M – – – 1750 8,2 11.0
Type BG/FS h3 h4 u2 q w z* z2* A AB B BB C H HA HD* LB*VG-95 100L 230 283 117 110 189 463 429 160 195 140 176 63 100 13 255 303VG-130 100L 230 283 117 110 198 472 438 160 195 140 176 63 100 13 255 303VG-155 112M 242 283 117 110 222 506 472 190 225 140 176 70 112 15 280 320VG-255 132S 262 318 120 130 300 656 616 216 256 140 218 110 132 18 320 426132M 178
BG = Baugröße, gilt für IE1 und IE2-Motoren* Abhängig von der Ausführung des Motors
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2)* Depending on the motor design
06/2015 | 1096.0911
23
009 006 004 003 002 001 08 06 04 33 009 006 004 003 002 001 08 06 04 33
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
6
4
2
0
25
20
15
10
5
0
260
240
220
200
180
160
140
120
100
80
60
40
20
0 8
7
6
5
4
3
2
1
0
10
8
6
4
2
0
140
120
100
80
60
40
20
0
VG-255
VG-95
VG-130
VG-155
VG-255
VG-95
VG-130
VG-155
VG-255
VG-95
VG-130
VG-95 / VG130
VG-255 / VG-155
VG-95 / VG130
VG-255 / VG-155
VG-255
VG-95
VG-130
VG-155
VG-255
VG-95
VG-130
VG-155
50 Hz-cycles | 1450 1/min - rpm 60 Hz-cycles | 1750 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - without valves
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - ohne Ventile
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
Gewindeausführung | Thread execution – VG-95 / 130 / 155 / 255
06/2015 | 1096.0911
24
**
*
*
II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - without valves
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - ohne Ventile
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connection
Teileliste / Part list047 Gleitringdichtung Mechanical seal161 Gehäusedeckel Casing cover230 Laufrad Impeller411/.1 Dichtring Sealing ring412 O-Ring O-ring441 Gehäuse für Wellendichtung Shaft seal casing550-.1 Scheibe Washer561 Kerbstift Grooved pin800 Motor Motor901/.1 6-kt. Schraube Hexagon head screw903/.1 Verschlussschraube Screw plug906 Laufradschraube Impeller screw920/.1 6-kt. Mutter Hexagon nut950 Tellerfeder Washer spring970 Typenschild Name plate
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing
VG-95 / 130 / 155 / 255 – Flanschausführung | Flange execution
Daten und Maße / Data and dimensions50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB Ue UL DN D1 D2VG-95 100L 1450 2,2 3.0 1750 3,0 4.0 52 115VG-130 100L 1450 3,0 4.0 1750 4,6 6.2 55 121 G 1/2 G 3/8 G 1/2 40 150 110VG-155 112M 1450 4,0 5.4 1750 6,2 8.3 71 157VG-255 132S 1450 5,5 7.4 – – – 102 225 G 1/2 G 1/2 G 1/2 50 165 125132M – – – 1750 8,2 11.0
Type BG/FS h3 h4 u2 q w z* z2* A AB B BB C H HA HD* LB*VG-95 100L 275 328 162 180 192 507 432 160 195 140 176 63 100 13 255 303VG-130 100L 275 328 162 180 201 516 441 160 195 140 176 63 100 13 255 303VG-155 112M 287 328 162 180 225 550 475 190 225 140 176 70 112 15 280 320VG-255 132S 312 370 170 200 283 689 605 216 256 140 218 110 132 18 320 426132M 178
BG = Baugröße, gilt für IE1 und IE2-Motoren, * Abhängig von der Ausführung des MotorsFlanschanschlussmaße nach EN 1092-2 PN 10, Ausführung nach ANSI auf Anfrage
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2), * Depending on the motor designFlanges dimensions in acc. with EN 1092-2 PN 10, execution in acc. with ANSI standards on request
06/2015 | 1096.0911
25
009 006 004 003 002 001 08 06 04 33 009 006 004 003 002 001 08 06 04 33
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
6
4
2
0
25
20
15
10
5
0
260
240
220
200
180
160
140
120
100
80
60
40
20
0 8
7
6
5
4
3
2
1
0
10
8
6
4
2
0
140
120
100
80
60
40
20
0
VG-255
VG-95
VG-130
VG-155
VG-255
VG-95
VG-130
VG-155
VG-255
VG-95
VG-130
VG-95 / VG130
VG-255 / VG-155
VG-95 / VG130
VG-255 / VG-155
VG-255
VG-95
VG-130
VG-155
VG-255
VG-95
VG-130
VG-155
50 Hz-cycles | 1450 1/min - rpm 60 Hz-cycles | 1750 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - without valves
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - ohne Ventile
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
Flanschausführung | Flange execution – VG-95 / 130 / 155 / 255
06/2015 | 1096.0911
26
***
*
VN-95 / 125 / 180 II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpssingle-stage - with valve flaps and port cylinder
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen und Nabensteuerung
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUe Entleerung (Verschlussschraube) Drainage (screw plug)
Teileliste / Part list047 Gleitringdichtung Mechanical seal106 Sauggehäuse Suction casing107 Druckgehäuse Discharge casing137 Steuernabe Port cylinder230 Laufrad Impeller411 Dichtring Sealing ring412 O-Ring O-ring550/.1 Scheibe Washer561 Kerbstift Grooved pin598 Blech Sheet746 Ventilklappe Valve flap800 Motor Motor901-.2 6-kt. Schraube Hexagon head screw903 Verschlussschraube Screw plug914/.1 Innen-6-kt. Schraube Hexagon socket head screw920 6-kt. Mutter Hexagon nut970 Typenschild Name plate
Daten und Maße / Data and dimensions50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UeVN-95 100 1450 3,0 4.0 1750 4,6/4,4** 6.2/5.9** 61 134
G 1/2 G 3/8VN-125 112M 1450 4,3 5.8 1750 6,6/6,3** 8.9/8.4** 72 159VN-180 132S 1450 5,5 7.4 – – – 97 214
132M – – – 1750 8,2 11.0 97 214
Type BG/FS h3 h4 w z* z2* A AB B BB C H HA HD* LB*VN-95 100 275 300 78 468 318 160 195 140 176 63 100 13 255 303VN-125 112M 287 300 85 517 335 190 225 140 176 70 112 15 280 320VN-180 132S 307 300 125 658 391 216 256 140 218 110 132 18 320 426132M 178
BG = Baugröße, gilt für IE1 und IE2-Motoren* Abhängig von der Ausführung des Motors** IE2-Motor
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2)* Depending on the motor design** IE2 motor (subtype 2)
06/2015 | 1096.0911
27
VN-95 / 125 / 180
009 006 004 003 002 001 08 06 04 33 009 006 004 003 002 001 08 06 04 33
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
40
30
20
10
0
10
8
6
4
2
0
220
200
180
160
140
120
100
80
60
40
20
0 8
7
6
5
4
3
2
1
0
10
8
6
4
2
0
130
120
110
100
90
80
70
60
50
40
30
20
10
0
VN-180
VN-125
VN-95
VN-180
VN-125
VN-95
VN-125
VN-95
VN-180 VN-180
VN-125
VN-95
VN-180
VN-125
VN-95
VN-180
VN-125
VN-95
50 Hz-cycles | 1450 1/min - rpm 60 Hz-cycles | 1750 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
inlet pressure p [inch Hg a] inlet pressure p [inch Hg a]
Liquid ring vacuum pumpssingle-stage - with valve flaps and port cylinder
Delivery of additional liquid All pump sizes can deliver up to 4 m³/h additional liquid within the given mo-tor power. If the motor power is higher up to 10 m³/h can be delivered. For IE2 motors (subtype 2) at 60 Hz with frame size 100 and 112 the additional liquid delivery is reduced.
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpeneinstufig - mit Ventilklappen und Nabensteuerung
Mitfördern von ZusatzflüssigkeitBei den angegebenen Motorleistungen können bei allen Baugrößen bis zu 4 m3/h Zusatzflüssigkeit mitgefördert werden. Bei höheren Motorleistungen kann bis zu 10 m3/h mitgefördert werden. Bei 60Hz-IE2-Motoren mit BG 100 und 112: verringerte Flüssigkeitsmitförderung.
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
28
**
*
*
C
VZ-30 / 50 II 2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpsdouble-stage
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpenzweistufig
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUC Kavitationsschutz Cavitation protectionUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connectionUV Anschluss für Entleerungsventil Connection for drainage valve
Teileliste / Part list047 Gleitringdichtung Mechanical seal106 Sauggehäuse Suction casing107 Druckgehäuse Discharge casing110/.1 Mittelkörper Stage casing137-.2 Steuerscheibe Inter casing230/.1 Laufrad Impeller411 Dichtring Sealing ring412 O-Ring O-ring504 Abstandsring Distance ring550 Scheibe Washer561 Kerbstift Grooved pin562 Zylinderstift Parallel pin902 Stiftschraube Stud903 Verschlussschraube Screw plug914 Innen-6-kt.Schraube Hexagon socket head screw920 6-kt.Mutter Hexagon nut940/.1 Passfeder Fitting key970 Typenschild Name plate
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing
Daten und Maße / Data and dimensions50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UC Ue UL UVVZ-30 80 2850 1,1 1.5 3450 1,5 2.0 31 68 G 1/4 G 1/8 G 1/4 G 1/4 G 1/4VZ-50 90S 2850 1,5 2.0 3450 2,2 3.0 34 75
Type BG/FS a h3 u1 u2 w z* z2* A AB BB C H HA HD*VZ-30 80 119 160 43 123 196 433 401 125 153 125 50 80 10 231VZ-50 90S 159 170 43 123 242 473 441 140 170 155 56 90 11 240
BG = Baugröße, gilt für IE1 und IE2-Motoren* Abhängig von der Ausführung des Motors
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2)* Depending on the motor design
06/2015 | 1096.0911
29
VZ-30 / 50
009 006 004 003 002 001 08 06 04 33 009 006 004 003 002 001 08 06 04 33
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
5
4
3
2
1
0
1.2
0.8
0.4
0
60
50
40
30
20
10
0 2,5
2,0
1,5
1,0
0,5
0
3,0
2,5
2,0
1,5
1,0
0,5
0
30
25
20
15
10
5
0
VZ-50
VZ-30
VZ-50
VZ-50
VZ-30
VZ-30
VZ-50
VZ-30
VZ-50
VZ-30
VZ-50
VZ-30
50 Hz-cycles | 2850 1/min - rpm 60 Hz-cycles | 3450 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpsdouble-stage
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpenzweistufig
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
30
**
*
*
VZ-110 / 140 / 180 II 1/2 G
Subject to technical modifications and error.
Liquid ring vacuum pumpsdouble-stage
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpenzweistufig
Anschlüsse / ConnectionsUB Anschluss für Betriebsflüssigkeit Connection for operation liquidUC Kavitationsschutz Cavitation protectionUe Entleerung (Verschlussschraube) Drainage (screw plug)UL Anschluss für Belüftungsventil Vacuum relief valve connectionUm Anschluss für Manometer Pressure gauge connectionUS3 Anschluss für Sensor Connection for sensorUV Anschluss für Entleerungsventil Connection for drainage valve
Teileliste / Part list047 Gleitringdichtung Mechanical seal106 Sauggehäuse Suction casing107 Druckgehäuse Discharge casing110/.1 Mittelkörper Stage casing137-.2 Steuerscheibe Inter casing230/.1 Laufrad Impeller360 Lagerdeckel Bearing cover411-.3 Dichtring Sealing ring412/.1 O-Ring O-ring525 Abstandshülse Distance sleeve550 Scheibe Washer561 Kerbstift Grooved pin562 Zylinderstift Parallel pin901/.1 6-kt. Schraube Hexagon head screw903-.3 Verschlussschraube Screw plug914 Innen-6-kt. Schraube Hexagon socket head screw940/.1 Passfeder Fitting key970 Typenschild Name plate
Maßzeichnung / Dimensional drawing
Schnittzeichnung / Sectional drawing
Daten und Maße / Data and dimensions50 Hz / cycles 60 Hz / cycles Gewicht/Weight Anschlüsse / Connections
Type BG/FS 1/min kW HP 1/min kW HP kg lbs UB UC Ue Ue1 UL Um US3 UVVZ-110 100L 1450 3,0 4.0 1750 4,0 5.4 92 203VZ-140 112M 1450 4,0 5.4 1750 5,5 7.4 110 243 G 1/2 G 1/4 G 1/2 G 1/4 G 1/2 G 1/4 G 3/4 G 1/2VZ-180 132S 1450 5,5 7.4 1750 8,2 11.0 132 291
Type BG/FS a m1 m2 z* z2* AD* LB*VZ-110 100L 239 333 299 659 592 155 303VZ-140 112M 269 363 329 715 648 168 329VZ-180 132S 339 433 399 835 769 188 379
BG = Baugröße, gilt für IE1 und IE2-Motoren* Abhängig von der Ausführung des MotorsFlanschanschlussmaße nach EN 1092-2 PN 10 und ANSI B 16.5
VZ-110 / 140 / 180 auch in Grundplattenbauweise erhältlich.Siehe Prospekt Flüssigkeitsring-Vakuumpumpen – Grundplatten-Bauweise: VZ-110G / 140G / 180G
FS = Frame size, valid for IE1 motors and IE2 motors (subtype 2)* Depending on the motor designFlange connecting dimensions according to EN 1092-2 PN 10 and ANSI B 16.5
VZ-110 / 140 / 180 also available in base plate version. See brochure Liquid ring vacuum pumps – base plate version: VZ-110G / 140G / 180G
06/2015 | 1096.0911
31
VZ-110 / 140 / 180
009 006 004 003 002 001 08 06 04 33 009 006 004 003 002 001 08 06 04 33
1 2 3 4 5 6 7 8 10 15 20 26 1 2 3 4 5 6 7 8 10 15 20 26
20
15
10
5
0
250
225
200
175
150
125
100
75
50
25
0 7
6
5
4
3
2
1
0
8
6
4
2
0
140
120
100
80
60
40
20
0
5
4
3
2
1
0
VZ-180
VZ-140
VZ-110
VZ-180
VZ-140
VZ-110
VZ-180
VZ-140
VZ-110
VZ-110 / 140 / 180 VZ-110 / 140 / 180
VZ-180
VZ-140
VZ-110
50 Hz-cycles | 1450 1/min - rpm 60 Hz-cycles | 1750 1/min - rpm
Subject to technical modifications and error.
Suction capacity and power consumption depending on inlet pressureThe characteristics are applicable for compression of 20 °C (68 °F) dry air from inlet pressure to atmospheric pressure (1013 mbar / 30 inch Hg a) for nominal speed and drive with three phase motors. Ring liquid is water at 15 °C (59 °F). The tolerance of the suction capacity is –10 % and of the power consumption +10 %. With different operating conditions the characteristic curves change (e.g. differing gas operating liquid conditions, conveying of additional liquids and/or pumping of gas-steam mixtures).
Q[CFM]
Suct
ion
capa
city
P[HP]
Pow
er c
onsu
mpt
ion
[GPM]
Wat
erre
quire
men
t
Inlet pressure p [inch Hg a] Inlet pressure p [inch Hg a]
Liquid ring vacuum pumpsdouble-stage
Technische Änderungen und Irrtum vorbehalten.
Saugvermögen und Leistungsbedarf in Abhängigkeit vom AnsaugdruckDie Kennlinien gelten bei Verdichtung trockener Luft von 20 °C vom Ansaug-druck auf Atmosphärendruck (1013 mbar) bei Nenndrehzahl und Antrieb mit Drehstrommotoren. Betriebsflüssigkeit ist Wasser mit 15 °C. Die Toleranz des Saugvermögens beträgt –10 %, die des Leistungsbedarfs +10 %. Bei abweichenden Betriebsbedingungen (z.B. abweichende Daten des zu fördernden Gases oder der Betriebsflüssigkeit, Mitförderung von Zusatzflüs-sigkeit, Förderung von Gas-Dampf gemischen) ändern sich die Kennlinien.
P[kW]
Leis
tung
sbed
arf
[l/min]
Was
serb
edar
f
Q[m3/h]
Saug
verm
ögen
Ansaugdruck p [mbar]Ansaugdruck p [mbar]
Flüssigkeitsring-Vakuumpumpenzweistufig
50 Hz | Kennlinien / Characteristic curves 60 Hz | Kennlinien / Characteristic curves
06/2015 | 1096.0911
32
VI / V
Subject to technical modifications and error.
Liquid ring vacuum pumpsClose-coupled version
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpen Blockbauweise
Baureihe V – Typenschlüssel / V Series – Type Code
Beispiel Example V -155 -55 -001Pumpentype Pump type
Pumpengröße Pump size
T1 Werkstoffausführung Material design
Zählnummer Sequence number
T1: Schlüssel Werkstoffausführung / Code material designSchlüssel / Code 35 45 55 55 65Typ / Type V-30 – 430 V-6 V-30 – 255 V-330 / 430 V-30 – 430
Gehäuse Casing
EN-GJL-250 Cast iron
CuZnBrass
EN-GJL-250 Cast iron
EN-GJL-250 Cast iron
1.4581 CrNiMo-cast steel
Steuerscheibe Inter casing
1.4301 CrNi-steel
1.4301 CrNi-steel
1.4301 CrNi-steel
1.4301 CrNi-steel
1.4571 CrNiMo-steel
Laufrad Impeller
1.4581 CrNiMo-cast steel
CuSnBronze
RG-5 Red bronze
GBzBronzeCuSn
1.4581 CrNiMo-cast steel
Gehäuse für Wellendicht.Shaft seal casing
EN-GJL-250 Cast iron
CuZnBrass
EN-GJL-250 Cast iron
EN-GJL-250 Cast iron
1.4581 CrNiMo-cast steel
Gleitringdichtung Mechanical seal
Kohle, Cr-Stahl, NBR Carbon, Cr-steel, NBR
Kohle, SiC, FKM Carbon, SiC, FKM
Kohle, Cr-Stahl, NBR Carbon, Cr-steel, NBR
Kohle, Cr-Stahl, NBR Carbon, Cr-steel, NBR
Kohle, CrNiMo-Stahl, FKM Carbon, CrNiMo-steel, FKM
Ventilklappe Valve flap PTFE PTFE PTFE PTFE PTFE
EN-GJL-250 = EN-JL1040 = GG-25 = FGL 250
Baureihe VI – Typenschlüssel / VI Series – Type Code
Beispiel Example VI -30 -55 -001Pumpentype Pump type
Pumpengröße Pump size
T1 Werkstoffausführung Material design
Zählnummer Sequence number
T1: Schlüssel Werkstoffausführung / Code material designSchlüssel / Code 45 45 55 65Typ / Type VI-2 VI-8 / 18 / 25 VI-30 / 55 VI-30 / 55
Gehäusedeckel Casing cover
CuZnBrass
CuSnBronze
1.4308 CrNi-cast steel
1.4581 CrNiMo-cast steel
Steuerscheibe Inter casing
1.4301 CrNi-steel
1.4301 CrNi-steel
1.4301 CrNi-steel
1.4571, SiC-beschichtet CrNiMo-steel, SiC coated
Laufrad Impeller
CuSnBronze
CuSnBronze
CuSnBronze
1.4581 CrNiMo-cast steel
Welle Shaft
1.4122 CrMo-steel
1.4122 CrMo-steel
1.4122 CrMo-steel
1.4571 CrNiMo-steel
Gehäuse für Wellendicht. Shaft seal casing
CuZnBrass
CuSnBronze
EN-GJL-250 Cast iron
1.4581 CrNiMo-cast steel
Gleitringdichtung Mechanical seal
Kohle, SiC, FKM Carbon, SiC, FKM
Kohle, SiC, FKM Carbon, SiC, FKM
Kohle, Cr-Stahl, NBR Carbon, Cr-steel, NBR
Kohle, CrNiMo-Stahl, FKM Carbon, CrNiMo-steel, FKM
Ventilklappe Valve flap PTFE PTFE PTFE PTFE
EN-GJL-250 = EN-JL1040 = GG-25 = FGL 250
06/2015 | 1096.0911
33
VG/ VN
Subject to technical modifications and error.
Liquid ring vacuum pumpsClose-coupled version
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpen Blockbauweise
Baureihe VG – Typenschlüssel / VG Series – Type Code
Beispiel Example VG -155 -56 -001Pumpentype Pump type
Pumpengröße Pump size
T1 Werkstoffausführung Material design
Zählnummer Sequence number
T1: Schlüssel Werkstoffausführung / Code material designSchlüssel / Code 36 56 60Typ / Type VG-30 – 255 VG-30 – 255 VG-30 – 255
Gehäusedeckel Casing cover
1.4308 CrNi-cast steel
1.4308 CrNi-cast steel
1.4308 CrNi-cast steel
Laufrad Impeller
1.4581 CrNiMo-cast steel
RG-5 Red bronze
1.4581 CrNiMo-cast steel
Gehäuse für Wellendicht. Shaft seal casing
EN-GJL-250 Cast iron
EN-GJL-250 Cast iron
1.4581 CrNiMo-cast steel
Gleitringdichtung Mechanical seal
Kohle, Cr-Stahl, NBR Carbon, Cr-steel, NBR
Kohle, Cr-Stahl, NBR Carbon, Cr-steel, NBR
Kohle, CrNiMo-Stahl, FKM Carbon, CrNiMo-steel, FKM
EN-GJL-250 = EN-JL1040 = GG-25 = FGL 250
Baureihe VN – Typenschlüssel / VN Series – Type Code
Beispiel Example VN -125 -40 -001Pumpentype Pump type
Pumpengröße Pump size
T1 Werkstoffausführung Material design
Zählnummer Sequence number
T1: Schlüssel Werkstoffausführung / Code material designSchlüssel / Code 40 50 50Typ / Type VN-95 / 125 / 180 VN-95 VN-125/180
Sauggehäuse Suction casing
CuSnBronze
EN-GJL-250 Cast iron
EN-GJL-250 Cast iron
Druckgehäuse Discharge casing
CuSnBronze
EN-GJL-250 Cast iron
EN-GJL-250 Cast iron
Steuernabe Port cylinder
CuSnBronze
CuSnBronze
CuZn Brass
Laufrad Impeller
RG-7 Red bronze
RG-7 Red bronze
CuZn Brass
Gleitringdichtung Mechanical seal
Kohle, CrNiMo-Stahl, FKM Carbon, CrNiMo-steel, FKM
Kohle, Cr-Stahl, FKM Carbon,Cr-steel, FKM
Kohle, Cr-Stahl, FKM Carbon,Cr-steel, FKM
Ventilklappe Valve flap PTFE PTFE PTFE
EN-GJL-250 = EN-JL1040 = GG-25 = FGL 250
06/2015 | 1096.0911
34
VZ
Subject to technical modifications and error.
Liquid ring vacuum pumpsClose-coupled version
Technische Änderungen und Irrtum vorbehalten.
Flüssigkeitsring-Vakuumpumpen Blockbauweise
Baureihe VZ – Typenschlüssel / VZ Series – Type Code
Beispiel Example VZ -110 -55 -001Pumpentype Pump type
Pumpengröße Pump size
T1 Werkstoffausführung Material design
Zählnummer Sequence number
T1: Schlüssel Werkstoffausführung / Code material designSchlüssel / Code 35 45 55 65Typ / Type VZ-30 / 50 / 110 / 140 / 180 VZ-30/ 50 VZ-30 / 50 / 110 / 140 / 180 VZ-110 / 140 / 180
Sauggehäuse Suction casing
EN-GJL-250 Cast iron
CuZnBrass
EN-GJL-250 Cast iron
1.4581 CrNiMo-cast steel
Druckgehäuse Discharge casing
EN-GJL-250 Cast iron
CuZnBrass
EN-GJL-250 Cast iron
1.4581 CrNiMo-cast steel
Steuerscheibe Inter casing
1.4301 CrNi-steel
1.4301 CrNi-steel
1.4301 CrNi-steel
1.4571, SiC-beschichtet CrNiMo-steel, SiC coated
Mittelkörper Stage casing
EN-GJL-250 Cast iron
CuZnBrass
EN-GJL-250 Cast iron
1.4581 CrNiMo-cast steel
Laufrad Impeller
1.4581 CrNiMo-cast steel
CuSnBronze
CuSnBronze
1.4581 CrNiMo-cast steel
Welle Shaft
1.4122 CrMo-steel
1.4122 CrMo-steel
1.4122 CrMo-steel
1.4571 CrNiMo-steel
Gleitringdichtung Mechanical seal
Kohle, Cr-Stahl, NBR Carbon, Cr-steel, NBR
Kohle, Cr-Stahl, NBR Carbon, Cr-steel, NBR
Kohle, Cr-Stahl, NBR Carbon, Cr-steel, NBR
Kohle, Edelstahl, FKM Carbon, stainless steel, FKM
EN-GJL-250 = EN-JL1040 = GG-25 = FGL 250
06/2015 | 1096.0911
D Produktion / Verwaltung Production / Administration
Speck PumpenRegensburger Ring 6 – 8, 91154 Roth
Tel.: +(49) 9171 809 0Fax: +(49) 9171 809 10
D Germany
Deutschland OstHuckauf Ingenieure GmbHRathausstraße 509244 LichtenauTel.: +49 37208 660 80Fax: +49 37208 660 [email protected]
BerlinHuckauf Ingenieure GmbHFontanepromenade 1710967 BerlinTel.: +49 30 890 959 92Fax: +49 30 890 959 [email protected]
NorddeutschlandIngenieure Willy Wandrach GmbHFlurstraße 10522549 HamburgTel.: +49 40 398 624 0Fax: +49 40 398 624 [email protected]
Hannover, KasselIVT – Pumpen GmbHZum Wischfeld 1A31749 AuetalTel.: +49 5752 929 597Fax: +49 5752 929 599Mobile: +49 172 511 699 [email protected]
KölnHuckauf Ingenieure GmbHGrillenpfad 2840764 LangenfeldTel.: +49 2173 914 560Fax: +49 2173 914 [email protected]
Bayern, Baden-WürttembergSpeck PumpenVERKAUFSGESELLSCHAFT GmbHHauptstraße 1 – 391233 Neunkirchen a. SandTel.: +49 9123 949 – 0Fax: +49 9123 949 – [email protected]
Service
Deutschland MitteFSE Fluid Systems ErfurtPoeler Weg 699085 ErfurtTel.: +49 361 550 715 0Fax: +49 361 550 715 [email protected]
KölnArpuma GmbHOttostrasse 1050170 KerpenTel.: +49 2273 953 300 0Fax: +49 2273 953 300 [email protected]
International
A AustriaTuma Pumpensysteme GmbHEitnergasse 121230 WienTel.: +43 191 493 40Fax.: +43 191 414 [email protected]
AUS AustraliaPump Solutions AustralasiaUnit 17 Bessemer WayWangara, WA 6065P.O. Box 1811Wangara DC, WA 6947Tel.: +61 8 9408 1544Fax: +61 8 9408 [email protected]
Pump Systems AustraliaFactory 221 London DriveBayswater /MelbourneVictoria 3153Tel.: +61 397 623 100Fax: +61 397 623 [email protected]
B BelgiumHeat transfer pumps / Pompes pour fluid thermiqueFLOWMOTION BVBAMergelweg 31730 AsseTel.: +32 2 309 67 13Fax. +32 2 309 69 [email protected]
SPECK - Pompen Belgie N.V.Bierweg 249880 AalterTel.: +32 937 530 39Fax: +32 932 500 [email protected]
BG BulgariaEVROTECH OOD54 A, Manastirska Str.1111 SofiaTel.: +359 2 971 32 73Fax: +359 2 971 22 88 [email protected] CH Switzerland
Speck Pumpen SubsidiarySpeck Pumpen Industrie GmbHBürglenweg 48854 GalgenenTel.: +41 554 425 094Fax: +41 554 425 [email protected]
Sales and ServiceHänyTec AGGschwäbring 196244 NebikonTel.: +41 62 544 33 00Fax: +41 62 544 33 [email protected]
ServiceMEYER ARMATUREN PUMPEN GMBHRigackerstrasse 195610 WohlenTel. + 41 56 622 77 33Fax + 41 56 622 77 [email protected]
CN ChinaSpeck Pumpen SubsidiaryJiashan SPECK PUMPSSystemtechnik Ltd. No. 57, Hong Qiao Rd., No. 4 Economical Developing Zone,314100 Jiashan Xian, Zhejiang ProvinceTel.: +86 573 847 312 98Fax: +86 573 847 312 [email protected] www.speck-pumps.cn
CZ Czech RepublicSigmet spol s.r.o.Kosmonautu č.p. 1103/6a77200 OlomoucTel.: +420 585 231 070Fax: +420 585 227 [email protected]
DK DenmarkPumpegruppen a/sLundtoftegårdsvej 952800 LyngbyTel.: +45 459 371 00Fax: +45 459 347 [email protected]
E SpainSpeck Pumpen SubsidiarySPECK BOMBAS INDUSTRIALES, S.L.U.Trafalgar, 53 despacho 6Centro de Negocios CNAF46023 Valencia Tel.: +34 963 811 094Fax: +34 963 811 096Mobile: +34 618 376 [email protected]
F FranceSpeck Pumpen SubsidiarySpeck Pompes Industries S.A.Z.I. Parc d’Activités du Ried4, rue de l’EnergieB.P. 22767727 Hoerdt CedexTel.: +33 3 88 68 26 60Fax: +33 3 88 68 16 [email protected]
GB Great BritainSpeck Pumpen ABC LtdAreenA HouseMoston Road, Elworth, SandbachCheshire CW11 3HLTel.: +44 844 764 063 2Fax: +44 844 764 063 [email protected]
GR GreeceSPECK HellasSalaminos St. 5417676 KallitheaTel.: +30 210 956 500 6Fax: +30 210 957 747 [email protected]
I ItalyCentrifugal pumps / Pompe centrifugheSpeck Industries S.r.l Via Garibaldi, 5320010 Canegrate (MI)Tel.: +39 0331 405 805Mobile: +39 339 16 59 [email protected]
Vacuum pumps / Pompe per vuotoRio Nanta S.r.l.Via Mauro Macchi, 4220124 MilanoTel. +39 028 940 642 1Fax: +39 028 323 913Mobile: +39 339 658 781 [email protected]
IL IsraelAmbi-TechElectronics Engineering Ltd.,20 Ta’as st.;Industrial Area, Kfar-SabaP.O. Box 50Kfar-Saba 44425Tel.: +972 976 775 00Fax: +972 976 774 [email protected]
Small pumps /heat transfer pumps : Ringel Brothers (1973) Ltd.134 Hertzel St.P.O. Box 5148Tel-Aviv 66555Tel.: +972 368 255 05Fax: +972 368 220 41Mobile: +972 544 623 [email protected]
IND IndiaFlux Pumps India Pvt. Ltd.427/A-2, Gultekdi Industrial EstateNear Prabhat Printing PressPune – 411 047, MaharashtraTel.: +91 020 2427 1023Fax: +91 020 2427 0689Mobile: +91 98504 [email protected]
J JapanRodateq, Inc.Suite 301 Oka Bldg.2 - 1 - 16 Kyomachibori, Nishiku550 – 0003 OsakaTel.: +81 664 441 940Fax: +81 664 449 [email protected]
Rodateq, Inc.Tokyo BranchNo. 408, 3 - 22 - 12Highashi Ikebukuro, Toshima - ku170-0013 TokyoTel.: +81 359 798 818Fax: +81 359 798 [email protected]
L LuxembourgHeat transfer pumps / Pompes pour fluid thermiqueFLOWMOTION BVBAMergelweg 31730 AsseTel.: +32 2 309 67 13Fax. +32 2 309 69 [email protected]
MAL MalaysiaLeesonmechEngineering ( M ) Sdn. Bhd.No. 18 Jalan 18, Taman Sri Kluang,86000 Kluang, JohorTel.: +607 777 105 5Fax: +607 777 106 [email protected]
N NorwayIng. Per Gjerdrum A/SP.O. Box 154Nye Vakasvei 281360 NesbruTel.: +47 667 756 00Fax: +47 667 756 [email protected]
NL NetherlandsCentrifugal pumps / CentrifugaalpompenSpeck Pompen Nederland B.V.Businesspark 7PoortStationspoort 106902 KG ZevenaarTel.: +31 316 331 757Fax: +31 316 528 [email protected] www.speck.nl
Vacuum pumps / VacuümpompenDOVAC B.V.Meer en Duin 2282163 HD LisseTel.: +31 252 423 363Fax: +31 252 417 [email protected]
Heat transfer pumps / Pompes pour fluid thermiqueFLOWMOTION BVBAMergelweg 31730 AsseTel.: +32 2 309 67 13Fax. +32 2 309 69 [email protected]
NZ New ZealandMacEwans Pumping Systems Ltd.19 Ride WayNorth Harbour Industrial EstateTel.: +64 941 548 60Fax: +64 941 548 [email protected]
P PortugalUltra ControloProjectos Industriais, Lda.Quinta Lavi – Armazém 8Abrunheira27 10 - 089 SintraTel.: +351 219 154 350Fax: +351 219 259 [email protected]
PL PolandE.A. Krupinski Elzbieta Krupinskaul. Przymiarki 4A31-764 KrakowTel. / Fax: +48 126 455 [email protected]
RC TaiwanSpeck Pumpen SubsidiarySpeck Pumps Technology Taiwan Ltd.2Fl., no. 153, Sec. 2Datong Rd., Xizhi DistrictNew Taipei CityTel.: +886 286 926 220Fax: +886 286 926 759Mobile: +886 936 120 [email protected]
RCH ChileW & F Ingenieria Y Maquinas S.A.Felix de Amesti 90, Piso 6Las Condes, SantiagoTel.: +56 220 629 43Fax: +56 220 630 [email protected]
RI IndonesiaPT Roda Rollen IndonesiaKompleks Pertokoan Glodok Jaya No. 30Jl. Hayam Wuruk,Jakarta - PusatIndonesia, 11180Tel.: +6221 659 922 528Fax: +6221 380 595 [email protected]
ROK CoreaJ.C. International Inc.2F, Bikeum Bldg. 108,Yanghwa-Ro, Mapo-Gu,121-893 SeoulTel.: +82 232 628 00Fax: +82 232 569 [email protected]
RO RomaniaS.C. Gimsid S.R.L.Str. Arcului nr. 9, Arp.2021031 BucurestiTel.: +40 21 2118701Fax: +40 21 [email protected]
S SwedenHugo Tillquist ABP.O.Box 112016422 Kista Tel.: +46 859 463 200Fax: +46 875 136 [email protected]
SK Slovakian Republic Czech Republic (CZ)
SLO SloveniaSLOTEH Branko Gabric s.p.Zagrebška cesta 202000 MariborTel.: +38 624 614 460Fax: +38 624 614 [email protected]
SGP Singapore Malaysia (MAL)
T ThailandSpeck Pumpen SubsidiaryPump Systems Flux & Speck Co. Ltd.181/4 Soi AnamaiSrinakarin RoadSuanluang Bangkok 10250Tel.: +662 320 256 7Fax: +662 322 248 [email protected]
TR TurkeySpeck PompaSan. ve Tic. Ltd. Sti.Girne Mah., Kücükyali Is Merkezi B Blok No.12 Maltepe34852 IstanbulTel.: +90 216 375 750 5Fax: +90 216 375 753 3Mobil: +(90) 532 293 010 [email protected]
USA USASpeck Pumpen SubsidiarySpeck Industries LP301 Veterans BlvdRutherfordNJ 07070Tel.: +1 201 569 3114Fax: +1 201 569 [email protected]
ZA Rep. South AfricaAQUAPUMP ( Pty ) Ltd.Unit 54APD Industrial parkKelvin streetKya SandTel.: +27 117 080 600Fax: +27 865 864 151Mobile: +27 824 509 [email protected]
05_1
5
35
AusgabeEdition
06/2015Ersatz für Ausgabe
replaces edition04/2014
Vertretungen / Representations
D Produktion / Verwaltung Production / Administration
Speck PumpenRegensburger Ring 6 – 8, 91154 Roth
Tel.: +(49) 9171 809 0Fax: +(49) 9171 809 10
D Germany
Deutschland OstHuckauf Ingenieure GmbHRathausstraße 509244 LichtenauTel.: +49 37208 660 80Fax: +49 37208 660 [email protected]
BerlinHuckauf Ingenieure GmbHFontanepromenade 1710967 BerlinTel.: +49 30 890 959 92Fax: +49 30 890 959 [email protected]
NorddeutschlandIngenieure Willy Wandrach GmbHFlurstraße 10522549 HamburgTel.: +49 40 398 624 0Fax: +49 40 398 624 [email protected]
Hannover, KasselIVT – Pumpen GmbHZum Wischfeld 1A31749 AuetalTel.: +49 5752 929 597Fax: +49 5752 929 599Mobile: +49 172 511 699 [email protected]
KölnHuckauf Ingenieure GmbHGrillenpfad 2840764 LangenfeldTel.: +49 2173 914 560Fax: +49 2173 914 [email protected]
Bayern, Baden-WürttembergSpeck PumpenVERKAUFSGESELLSCHAFT GmbHHauptstraße 1 – 391233 Neunkirchen a. SandTel.: +49 9123 949 – 0Fax: +49 9123 949 – [email protected]
Service
Deutschland MitteFSE Fluid Systems ErfurtPoeler Weg 699085 ErfurtTel.: +49 361 550 715 0Fax: +49 361 550 715 [email protected]
KölnArpuma GmbHOttostrasse 1050170 KerpenTel.: +49 2273 953 300 0Fax: +49 2273 953 300 [email protected]
International
A AustriaTuma Pumpensysteme GmbHEitnergasse 121230 WienTel.: +43 191 493 40Fax.: +43 191 414 [email protected]
AUS AustraliaPump Solutions AustralasiaUnit 17 Bessemer WayWangara, WA 6065P.O. Box 1811Wangara DC, WA 6947Tel.: +61 8 9408 1544Fax: +61 8 9408 [email protected]
Pump Systems AustraliaFactory 221 London DriveBayswater /MelbourneVictoria 3153Tel.: +61 397 623 100Fax: +61 397 623 [email protected]
B BelgiumHeat transfer pumps / Pompes pour fluid thermiqueFLOWMOTION BVBAMergelweg 31730 AsseTel.: +32 2 309 67 13Fax. +32 2 309 69 [email protected]
SPECK - Pompen Belgie N.V.Bierweg 249880 AalterTel.: +32 937 530 39Fax: +32 932 500 [email protected]
BG BulgariaEVROTECH OOD54 A, Manastirska Str.1111 SofiaTel.: +359 2 971 32 73Fax: +359 2 971 22 88 [email protected] CH Switzerland
Speck Pumpen SubsidiarySpeck Pumpen Industrie GmbHBürglenweg 48854 GalgenenTel.: +41 554 425 094Fax: +41 554 425 [email protected]
Sales and ServiceHänyTec AGGschwäbring 196244 NebikonTel.: +41 62 544 33 00Fax: +41 62 544 33 [email protected]
ServiceMEYER ARMATUREN PUMPEN GMBHRigackerstrasse 195610 WohlenTel. + 41 56 622 77 33Fax + 41 56 622 77 [email protected]
CN ChinaSpeck Pumpen SubsidiaryJiashan SPECK PUMPSSystemtechnik Ltd. No. 57, Hong Qiao Rd., No. 4 Economical Developing Zone,314100 Jiashan Xian, Zhejiang ProvinceTel.: +86 573 847 312 98Fax: +86 573 847 312 [email protected] www.speck-pumps.cn
CZ Czech RepublicSigmet spol s.r.o.Kosmonautu č.p. 1103/6a77200 OlomoucTel.: +420 585 231 070Fax: +420 585 227 [email protected]
DK DenmarkPumpegruppen a/sLundtoftegårdsvej 952800 LyngbyTel.: +45 459 371 00Fax: +45 459 347 [email protected]
E SpainSpeck Pumpen SubsidiarySPECK BOMBAS INDUSTRIALES, S.L.U.Trafalgar, 53 despacho 6Centro de Negocios CNAF46023 Valencia Tel.: +34 963 811 094Fax: +34 963 811 096Mobile: +34 618 376 [email protected]
F FranceSpeck Pumpen SubsidiarySpeck Pompes Industries S.A.Z.I. Parc d’Activités du Ried4, rue de l’EnergieB.P. 22767727 Hoerdt CedexTel.: +33 3 88 68 26 60Fax: +33 3 88 68 16 [email protected]
GB Great BritainSpeck Pumpen ABC LtdAreenA HouseMoston Road, Elworth, SandbachCheshire CW11 3HLTel.: +44 844 764 063 2Fax: +44 844 764 063 [email protected]
GR GreeceSPECK HellasSalaminos St. 5417676 KallitheaTel.: +30 210 956 500 6Fax: +30 210 957 747 [email protected]
I ItalyCentrifugal pumps / Pompe centrifugheSpeck Industries S.r.l Via Garibaldi, 5320010 Canegrate (MI)Tel.: +39 0331 405 805Mobile: +39 339 16 59 [email protected]
Vacuum pumps / Pompe per vuotoRio Nanta S.r.l.Via Mauro Macchi, 4220124 MilanoTel. +39 028 940 642 1Fax: +39 028 323 913Mobile: +39 339 658 781 [email protected]
IL IsraelAmbi-TechElectronics Engineering Ltd.,20 Ta’as st.;Industrial Area, Kfar-SabaP.O. Box 50Kfar-Saba 44425Tel.: +972 976 775 00Fax: +972 976 774 [email protected]
Small pumps /heat transfer pumps : Ringel Brothers (1973) Ltd.134 Hertzel St.P.O. Box 5148Tel-Aviv 66555Tel.: +972 368 255 05Fax: +972 368 220 41Mobile: +972 544 623 [email protected]
IND IndiaFlux Pumps India Pvt. Ltd.427/A-2, Gultekdi Industrial EstateNear Prabhat Printing PressPune – 411 047, MaharashtraTel.: +91 020 2427 1023Fax: +91 020 2427 0689Mobile: +91 98504 [email protected]
J JapanRodateq, Inc.Suite 301 Oka Bldg.2 - 1 - 16 Kyomachibori, Nishiku550 – 0003 OsakaTel.: +81 664 441 940Fax: +81 664 449 [email protected]
Rodateq, Inc.Tokyo BranchNo. 408, 3 - 22 - 12Highashi Ikebukuro, Toshima - ku170-0013 TokyoTel.: +81 359 798 818Fax: +81 359 798 [email protected]
L LuxembourgHeat transfer pumps / Pompes pour fluid thermiqueFLOWMOTION BVBAMergelweg 31730 AsseTel.: +32 2 309 67 13Fax. +32 2 309 69 [email protected]
MAL MalaysiaLeesonmechEngineering ( M ) Sdn. Bhd.No. 18 Jalan 18, Taman Sri Kluang,86000 Kluang, JohorTel.: +607 777 105 5Fax: +607 777 106 [email protected]
N NorwayIng. Per Gjerdrum A/SP.O. Box 154Nye Vakasvei 281360 NesbruTel.: +47 667 756 00Fax: +47 667 756 [email protected]
NL NetherlandsCentrifugal pumps / CentrifugaalpompenSpeck Pompen Nederland B.V.Businesspark 7PoortStationspoort 106902 KG ZevenaarTel.: +31 316 331 757Fax: +31 316 528 [email protected] www.speck.nl
Vacuum pumps / VacuümpompenDOVAC B.V.Meer en Duin 2282163 HD LisseTel.: +31 252 423 363Fax: +31 252 417 [email protected]
Heat transfer pumps / Pompes pour fluid thermiqueFLOWMOTION BVBAMergelweg 31730 AsseTel.: +32 2 309 67 13Fax. +32 2 309 69 [email protected]
NZ New ZealandMacEwans Pumping Systems Ltd.19 Ride WayNorth Harbour Industrial EstateTel.: +64 941 548 60Fax: +64 941 548 [email protected]
P PortugalUltra ControloProjectos Industriais, Lda.Quinta Lavi – Armazém 8Abrunheira27 10 - 089 SintraTel.: +351 219 154 350Fax: +351 219 259 [email protected]
PL PolandE.A. Krupinski Elzbieta Krupinskaul. Przymiarki 4A31-764 KrakowTel. / Fax: +48 126 455 [email protected]
RC TaiwanSpeck Pumpen SubsidiarySpeck Pumps Technology Taiwan Ltd.2Fl., no. 153, Sec. 2Datong Rd., Xizhi DistrictNew Taipei CityTel.: +886 286 926 220Fax: +886 286 926 759Mobile: +886 936 120 [email protected]
RCH ChileW & F Ingenieria Y Maquinas S.A.Felix de Amesti 90, Piso 6Las Condes, SantiagoTel.: +56 220 629 43Fax: +56 220 630 [email protected]
RI IndonesiaPT Roda Rollen IndonesiaKompleks Pertokoan Glodok Jaya No. 30Jl. Hayam Wuruk,Jakarta - PusatIndonesia, 11180Tel.: +6221 659 922 528Fax: +6221 380 595 [email protected]
ROK CoreaJ.C. International Inc.2F, Bikeum Bldg. 108,Yanghwa-Ro, Mapo-Gu,121-893 SeoulTel.: +82 232 628 00Fax: +82 232 569 [email protected]
RO RomaniaS.C. Gimsid S.R.L.Str. Arcului nr. 9, Arp.2021031 BucurestiTel.: +40 21 2118701Fax: +40 21 [email protected]
S SwedenHugo Tillquist ABP.O.Box 112016422 Kista Tel.: +46 859 463 200Fax: +46 875 136 [email protected]
SK Slovakian Republic Czech Republic (CZ)
SLO SloveniaSLOTEH Branko Gabric s.p.Zagrebška cesta 202000 MariborTel.: +38 624 614 460Fax: +38 624 614 [email protected]
SGP Singapore Malaysia (MAL)
T ThailandSpeck Pumpen SubsidiaryPump Systems Flux & Speck Co. Ltd.181/4 Soi AnamaiSrinakarin RoadSuanluang Bangkok 10250Tel.: +662 320 256 7Fax: +662 322 248 [email protected]
TR TurkeySpeck PompaSan. ve Tic. Ltd. Sti.Girne Mah., Kücükyali Is Merkezi B Blok No.12 Maltepe34852 IstanbulTel.: +90 216 375 750 5Fax: +90 216 375 753 3Mobil: +(90) 532 293 010 [email protected]
USA USASpeck Pumpen SubsidiarySpeck Industries LP301 Veterans BlvdRutherfordNJ 07070Tel.: +1 201 569 3114Fax: +1 201 569 [email protected]
ZA Rep. South AfricaAQUAPUMP ( Pty ) Ltd.Unit 54APD Industrial parkKelvin streetKya SandTel.: +27 117 080 600Fax: +27 865 864 151Mobile: +27 824 509 [email protected]
05_1
5
06/2
015
– 10
96.0
911
Speck Pumpen Vakuumtechnik GmbH
Postfach 1453 · 91142 Roth / Germany Regensburger Ring 6 – 8 · 91154 Roth / Germany
Tel.: +49 91 71 809 - 0 Fax: +49 91 71 809 - 10
[email protected] www.speck.de