LINKBRIDGE™ PRESENTATION SCALING SWITCH with 5 Inputs … · The LinkBridge™ HDBaseT...

LINKBRIDGE™ PRESENTATION SCALING SWITCHwith 5 Inputs and Two Mirrored Outputs

BCI reserves the right to make changes to the products described herein withoutprior notice or consent. No liability is assumed as a result of their use or application.

All rights reserved.

©2019 Broadata Communications, Inc.

LBC-PSW52USER MANUAL

HDBaseT 18G/4K Multi-Format Presentation Switch w/ 5 Inputs and 2 Mirrored Outputs User Manual (LBC-PSW52)

SAFETY INSTRUCTIONS AND COMPLIANCE DECLARATION

PLEASE OBSERVE THE FOLLOWING SAFETY PRECAUTIONS

SURGE PROTECTION DEVICE RECOMMENDED

This product contains sensitive electrical components that may be damaged by electrical spikes,surges,electric shock,lightning strikes, etc. Use of surge proctection

system is highly recommended in order to protect and extend the life of your equipment.

DC POWER CONNECTION


3

Do not use this device near water/liquids. This device should not be exposed to dripping and splashing or liquids.

Clean only with dry cloth.

Do not use solvents such as paint thinners and acetone to clean external casing. Such agents will remove any labels on the device.

Do not block any ventilation openings.

Do not install near any sources of intense heat such as radiation, boilers, or other equipment that produce heat

Not intended for use/storage in close proximity of critical medical supplies such as those that might come into direct contact with patients or medical staff.

Protect the power cord from being pinched or damaged at receptacles and the point of exit from the device.

Only use attachment /accessories specified by manufacturer. If you have any questions about the compatibility of an accessory, contact your dealer.

In case liquid spillage on device, unplug mains power cord and contact your dealer. Continu-ous use in this case may result in fire or electric shock.

To reduce the risk of electric shock, do not touch connectors with wet hand.

Only power with the marked voltage on the device. Any other voltage can cause fire or elec-tric shock.

Do not use the device if an abnormality occurs. If any smoke or odor becomes apparent, un-plug the power cord and contact your dealer. Do not try to repair the device yourself.

Avoid using physically damaged devices. If your device metal housing is seriously physically damaged, the internal components may function abnormally. Contact your dealer.

Do not install the device in an area heavy with dust or constant high humidity. Operating the device in this case may result in fire or electric shock.

Only use supplied power supply. For a list of other compatible power supplies, contact your dealer.

Install this device in a secure location where it cannot be easily pushed or knocked over.

TABLE OF CONTENTS


PRODUCT DESCRIPTION

OPERATION CONTROL AND FUNCTIONS

FRONT/REAR PANEL

CONNECTOR PIN OUT ASSIGNMENT

WEB GUI CONFIGURATION

API COMMANDS (RS-232 & TELNET)

OSD MENU

SPECIFICATIONS

MAINTENANCE AND TROUBLESHOOTING

SERVICE PROCEDURE

REPLACEMENT POLICY

RETURN AND REPAIR SERVICE

LIMITED WARRANTY

5

7

7

11

12

19

26

35

38

39

39

39

40

1.0

2.0

2.1

3.0

4.0

5.0

5.1

6.0

7.0

8.0

9.0

10.0

5 PRODUCT DESCRIPTION


The LinkBridge™ HDBaseT Presentation Scaling Switch is a compact and robust switch that offers compact video and audio extension with the ability to scale 5 video inputs to 2 mirrored outputs. The Scaling Switch is capable of extending audio/video signals up to 70 meters over HDBaseT CAT 5e/6 cabling. An easily accessible source selection buttons allows you to select 5 Video Input signals and simultaneously send 2 audio/video output signals for a wide variety of applications. All while transmitting fully uncompressed Ultra HD and HDTV video resolutions up to 1080p @ 60Hz.

FEATURES:• Compact presentation scaling switch offers 5-Video Inputs (2-HDMI, 1-Display Port

and 2-VGA Inputs) to support a wide range of applications

• Source selection offers the simultaneous output of 2-video signals through HDBaseT and HDMI

• Extends HDMI/DisplayPort/VGA up to 70 meters over CAT 5e/6

• Scaling of any analog/digital video signal, up to 1080p & WUXGA to HDMI and HDBaseT protocol output

• Supports control via RS-232, Telnet, WebGUI, front panel control buttons or contact closures

• HDBaseT output supports remote powering

• Supports one microphone input (with phantom power), three unbalanced audio input and one stereo audio output

• Works with all LinkBridge LBH & LBC Series transmitters and receivers

IDEAL FOR:• Household entertainment sharing and control • Lecture room display and control • Showroom display and control • Meeting room presentation and control • Classroom display and control

6 PRODUCT DESCRIPTION


PACKAGE CONTENTS • 1- HDBaseT LinkBridge™ HDBaseT Presentation Scaling Switch1• 1- 24V/1A DC Power Adapter• 1- Power Cord• 1- Remote Control• 1- Operation Manual

SYSTEM REQUIREMENTS • Source equipment such as media players, video game consoles, PCs, or set-top

boxes.• A compatible HDBaseT receiver • The use of Premium High Speed HDMI cables, and industry standard CAT5,

CAT6a or CAT7 is highly recommended.

7 OPERATION CONTROL AND FUNCTIONS


FRONT PANELLBC-PSW52

1

“Menu” Button: Press this button to enter On Screen Display (OSD) menu.

“-“ (Minus) Button: Press button to navigate down on OSD menu.“+” (Plus) Button: Press button to navigate up on OSD menu.

“Lock” Button: Press this button to lock front panel.

LEDs: This LED for selected source indication. The LED for the selected source will illuminate for indicating active source.

IR Window: Receiving IR signal from remote control unit which comes with scaler box.

“Enter” Button: Press this button to confirm the selection on On Screen Display (OSD) menu.

“Select” Button: Press this button for source selection. The active source will be indicator on LEDs at front panel.

1

2

3

4

3

5

2 4

LOCK+

-ENTER

MENU

SELECT

HDMI1

DPHDMI2

1PC

2PC LOCK

6

7

5 6 7



REAR PANELLBC-PSW52

1 32 4 5 6 7 8 9

PC 1LINE INMIC INSERVIC IE R OUT IR IN RS232COM PORT

LINE OUT

CAT5e/6/7 OUTHDMI OUTHDMI 2HDMI D1 ISPLAY PORT

INPUT CONTROL

C 1 2 3 4 5

CONTROL

OFF

ON

PHANTOM

PC 2PC 1DC 24V

PC 2

Service: The service slot is for firmware update via USB.

Line Out: Connects with amplifier for audio source broadcasting.

MIC IN: Plug microphone in for audio source output. The phantom micro phone is well supported.

Phantom On/Off: Arrange the slide switch to “on” for condenser micro phone (5V) or “phantom” for professional 48V phantom microphone. When slide switch arrange to “off”, the audio output will be mute.

Line In: To output HDMI embedded audio of HDMI 1, 2 and display port source to DVD players.

PC1 / PC2: To output HDMI embedded audio of PC1 and PC2 source to DVD players.

IR Out: Connect with supplied IR blaster cable to sending IR single which comes from remote control unit to compatible Receivers.

IR In: Connect with supplied IR extender cable to receive the IR signal from the included IR remote. Ensure that the remote is within the direct line-of-sight of the IR extender.

RS-232: For sending RS-232 command to compatible Receivers.

1

2

3

4

5

6

7

8

9



REAR PANELLBC-PSW52 CON’T

113 124 5 6 7 8 9


LINE OUT


INPUT CONTROL

C 1 2 3 4 5

CONTROL

OFF

ON

PHANTOM

PC 2PC 1DC 24V

PC 2

Com Port: Connect with D-Sub 9 pin cable with PC or laptop for this scaler box controlled by RS-232 commands.

Control: This port is the link for WebGUI control; connect to an active Ethernet link with an RJ45 terminated cable. Use BCI’s IP Discovery program to obtain devices IP address to access WebGUI Control.

Input Sources: a. HDMI 1 & HDMI2: Connect to HDMI sources such as Blu-ray/ DVD player for both video and audio signal. b. DisplayPort: Connect to a PC / Laptop source for video signal input. c. PC 1 & PC2: Connect to a PC/Laptop source for video signal input with D-Sub 15pin cable.Output: a. CAT5e/6/7 Out: Connects with compatible Receiver for video and/or audio output. b. HDMI Out: Connect to an HDMI display or AV Receiver for video and/or audio output.

DC 24V: Plug the 24V DC power supply into the unit and connect the adap tor to an AC outlet.

10

11

12

13

14

Pin Number Source

Pin 1 HDMI 1Pin 2 HDMI 2Pin 3 DisplayPortPin 4 PC1Pin 5 PC2

15

Input Control: This input control reserving for direct source input selection. Connect ground pin (mark as C on panel) with following pin number for individual source selection.

13a

10

13b 13c 14a 14b 15



PIN DEFINE Tx/Rx1 N/C2 TxD3 RxD4 N/C5 GND6 N/C7 N/C8 N/C9 N/C

HDMI1 : HDMI 1 source input

HDMI2 : HDMI 2 source input DP: Display Port source input

PC1: PC1 source input


EXIT: Exit from On Screen Display (OSD)

MENU: Access to On Screen Display (OSD) RESET: Return to factory default setting (Ethernet setting remain the same)

AUTO ADJUST: Auto adjust PC picture in central

/ : Navigate down/up of On Screen Display selection items

(-) / (+): Adjust selection items parameter (+) or (-) of On Screen Display or output volume adjustment

1 2 3

4 5

1

2

3

4

5

11

10 98

7

6

7

8

9

10

11

6

11 CONNECTOR PINOUT ASSIGNMENT


1

2

3

Power

IR Signal

Not Used

1

2

3

IR Signal

Power

Ground

RS-232 Pin Out

PIN DEFINE Tx/Rx1 N/C2 TxD3 RxD4 N/C5 GND6 N/C7 N/C8 N/C9 N/C

IR Cable Pin Outs

IR Blaster Pin Out IR Extender

BAUD RATE 19200DATA BITS 8PARITY BITS NONEHDMI1 : HDMI 1 source input

HDMI2 : HDMI 2 source input DP: Display Port source input



EXIT: Exit from On Screen Display (OSD)

MENU: Access to On Screen Display (OSD) RESET: Return to factory default setting (Ethernet setting remain the same)

AUTO ADJUST: Auto adjust PC picture in central

/ : Navigate down/up of On Screen Display selection items

(-) / (+): Adjust selection items parameter (+) or (-) of On Screen Display or output volume adjustment

DC POWER CONNECTION


12

In order to make sure that you have a proper installation, please observe the following:1 Your AC jack has power.2. The 24VDC power supply is working.3. Your electrical system has proper grounding (this ensures that your power supply does not suffer from voltage variations).4. Power Surge Protection. This is optional, but highly recommended. A UPS system provides voltage regularity as well as prevents spikes from occurring, thus protecting your LBC-PSW52 from sensitive voltage conditions.

The LBC-PSW52 derives power from an external 24VDC power supply. This power supply is a wall mounted AC/DC adapter, 100-240 VAC, 50- 60 Hz, at 1A. This power supply comes standard for the LBC-PSW52 unless otherwise specified. To provide power to the LBC-PSW84, simply connect the power cord, already provided with the units, and connect it to the wall jack. (You will find one power cord per unit). Once the power cord has been connected to the wall jack, connect 24VDC to the unit and the unit should power up immediately flipping the power toggle swtichswitch. If you have any problems or concerns, regarding the installation, make sure that you have taken the proper steps to ensure a proper power connection. Otherwise, feel free to contact us for any questions you may have.Note 1: During installation, the installer may need to connect the power supply output to an appropriate Listed NEC type cable before it is routed behind a wall. Simply routing the power supply output cable behind a wall will most likely not comply with applicable installation requirements. Unit should only be powered by a power source that is Listed (NEC) Class 2 or a Listed ITE Power Supply marked/rated as LPS or Limited Power Source.

Note 2: The installation shall be in accordance with the applicable provisions of the National Electrical Code ANSI/NFPA 70, Article 725 and the Canadian Electrical Code, Part 1, Section 16.Note 3: The power supply shall not be permanently fixed to the building structure or similar structures.Note 4: The power supply shall not be located within environmental air handling spaces or within the wall cavity.Note 5: The power supply is to be located within the same vicinity as the A/V processing equipment in an ordinary location, Pollution Degree 2, secured to the equipment rack within the dedicated closet, podium or desk

13 WEB GUI CONFIGURATION


The WebGUI is divided up into multiple sections (Input, Lock, Information, Display, Picture, Audio, Miscellany, and Factory) allowing for all functions of the unit to be viewed and controlled directly. If desired, the numerical value for many of the items can be entered directly by typing it in the box above the slider bar. Press “Enter” to accept the newly entered value.

WEB USER SETTINGSThis section provides a way to change the password for the Administrator account. Click on “Save” to confirm and activate any changes made to these settings. Click on “Logout” to leave the Web GUI page.Note: The default user name is “admin”. The default password is “password”.



INPUTThis section allows for control of input selection with a choice between HDMI1, HDMI2, DP, PC1, and PC2. Once a selection is made, the switch will occur immediately.

LOCK This section provides a way to turn the front panel lock on and off.

INFORMATION This section provides details about the current input and output signals, as well as the firmware version of the unit.



DISPLAYThis section allows for control of the output resolution, size (aspect ratio), and HDCP behavior for all 3 digital inputs on the unit. There are also controls for the signal type expected by each PC input. Enabling "Comp In" for a PC input allows YUV (component video) signals to be used.



PICTURE This section provides detailed controls for the output's RGB levels, contrast, and brightness for all input types. Additional controls for hue, saturation, sharpness and noise reduction are provided for digital input signals while H/V position, Phase, Clock and WXGA support is provided for the PC inputs.



AUDIOThis section provides controls for the Mic audio mixer as well as embedded audio. The microphone input volume, audio delay and output volume can be directly controlled. The preferred embedded audio source for each digital input may also be selected, and the input volume for each audio source can be set independently.



MISCELLANY This section provides controls for auto input, auto sync off, OSD settings as well as EDID management. The EDID from one of the 2 outputs can be copied and used with any of the unit's digital inputs.



NETWORKThis section provides controls for the IP configuration. The IP Address, Netmask and Gateway can be set manually, or DHCP can be enabled for automatic IP configuration if the local network supports it. Click on “Display Current Setting” to display the current IP configuration. Click on “Apply” to confirm and activate any changes made to these settings.

Note: The default IP address is 192.168.1.254. If the IP address is changed then the IP address required for WebGUI and Telnet access will also change accordingly.

FACTORY This section provides a way to perform a factory reset on the unit.

FIRMWARE UPGRADE To update the unit's firmware, click the “Choose File” button to open the file selection window and then select the firmware update file (*.bin format) located on your local PC. After selecting the file, click the “Upgrade” button to begin the firmware update process. Once the process completes the unit will automatically reboot.

20 API COMMANDS (RS232 & TELNET)


RS-232 AND TELNET COMMANDS

# Command Description1 ? List all commands. 2 R VERSION Get firmware version.3 S FACTORY-RESET Return to factory default settings. 4 S SOURCE x Set input source.

x =0~4 0=HDMI 1 1=HDMI 2 2=DP 3=PC 1 4=PC 2

5 R SOURCE Read current input source. 6 S LOCK x Set lock button status.

x =0, 1 0=Unlock 1=Lock

7 R LOCK Read lock button status. 8 S OUTPUT x Set output resolution.

x =0~23 0=640×480 1=800×600 2=1024×768 3=1280×768 4=1360×768 5=1280×720 6=1280×800 7=1280×1024 8=1440×900 9=1400×1050 10=1680×1050 11=1600×1200 12=1920×1080 13=1920×1200 14=720×480P 15=1280×720P60 16=1920×1080I60 17=1920×1080P60 18=720×576P 19=1280×720P50 20=1920×1080I50 21=1920×1080P50 22=NATIVE OUT1 23=NATIVE OUT2



# Command Description1 ? List all commands. 2 R VERSION Get firmware version.3 S FACTORY-RESET Return to factory default settings. 4 S SOURCE x Set input source.

x =0~4 0=HDMI 1 1=HDMI 2 2=DP 3=PC 1 4=PC 2

5 R SOURCE Read current input source. 6 S LOCK x Set lock button status.

x =0, 1 0=Unlock 1=Lock

7 R LOCK Read lock button status. 8 S OUTPUT x Set output resolution.

x =0~23 0=640×480 1=800×600 2=1024×768 3=1280×768 4=1360×768 5=1280×720 6=1280×800 7=1280×1024 8=1440×900 9=1400×1050 10=1680×1050 11=1600×1200 12=1920×1080 13=1920×1200 14=720×480P 15=1280×720P60 16=1920×1080I60 17=1920×1080P60 18=720×576P 19=1280×720P50 20=1920×1080I50 21=1920×1080P50 22=NATIVE OUT1 23=NATIVE OUT2

# Command Description9 R OUTPUT Read output resolution. 10 S SIZE x Set output aspect.

x =0~6 1=Full 2=Follow Input 3=Pan Scan 4=Letter Box 5=Under 2 6=Under 1

11 R SIZE Read output aspect setting. 12 S HDMI1-HDCP x Set HDCP mode for HDMI 1.

x =0,1 0=Enable1=Disable

13 R HDMI1-HDCP Read HDCP status for HDMI 1. 14 S HDMI2-HDCP x Set HDCP mode for HDMI 2.

x =0,1 0=Enable1=Disable

15 R HDMI2-HDCP Read HDCP status for HDMI 2. 16 S DP-HDCP x Set HDCP mode for DisplayPort.

x =0, 1 0=Enable1=Disable

17 R DP-HDCP Read HDCP status for DisplayPort.18 S PC1-COMP x Set PC1 component support mode.

x =0, 1 0=RGBHV [PC] 1=YUV [Component Video]

19 R PC1-COMP Read PC1 Component input state. 20 S PC2-COMP x Set PC2 component support mode.

x =0, 1 0=RGBHV [PC] 1=YUV [Component Video]

21 R PC2-COMP Read PC2 Component input state. 22 S CONTRAST x Set contrast.

x =0~60 23 R CONTRAST Read contrast setting. 24 S BRIGHTNESS x Set brightness.

x =0~60 25 R BRIGHTNESS Read brightness setting.



# Command Description26 S COLOR-R x Set red color level.

x =0~1023 27 R COLOR-R Read red color level. 28 S COLOR-G x Set green color level.

x =0~1023 29 R COLOR-G Read green color level. 30 S COLOR-B x Set blue color level.

x =0~1023 31 R COLOR-B Read blue color level. 32 S HUE x Set hue.

x =0~60 33 R HUE Read hue setting. 34 S SATURATION x Set saturation.

x =0~60 35 R SATURATION Read saturation setting.36 S SHARPNESS x Set sharpness.

x =0~30 37 R SHARPNESS Read sharpness setting. 38 S NR x Set noise reduction level.

x =0~3 0=Off 1=Low 2=Middle 3=High

39 R NR Read noise reduction setting.40 S PC-AUTO x Activate auto size detection function for

the PC source. x =0,10=Disable1=Enable

41 S PC-H-POS x Set horizontal position of the PC source. x =0~60

42 R PC-H-POS Read horizontal position of PC source. 43 S PC-V-POS x Set vertical position of the PC source.

x =0~60 44 R PC-V-POS Read vertical position of PC source. 45 S PC-PHASE x Set PC source phase.

x =0~30 46 R PC-PHASE Read PC source phase. 47 S PC-CLOCK x Set PC source clock

x =700~230048 R PC-CLOCK Read PC source clock.



# Command Description26 S COLOR-R x Set red color level.

x =0~1023 27 R COLOR-R Read red color level. 28 S COLOR-G x Set green color level.

x =0~1023 29 R COLOR-G Read green color level. 30 S COLOR-B x Set blue color level.

x =0~1023 31 R COLOR-B Read blue color level. 32 S HUE x Set hue.

x =0~60 33 R HUE Read hue setting. 34 S SATURATION x Set saturation.

x =0~60 35 R SATURATION Read saturation setting.36 S SHARPNESS x Set sharpness.

x =0~30 37 R SHARPNESS Read sharpness setting. 38 S NR x Set noise reduction level.

x =0~3 0=Off 1=Low 2=Middle 3=High

39 R NR Read noise reduction setting.40 S PC-AUTO x Activate auto size detection function for

the PC source. x =0,10=Disable1=Enable

41 S PC-H-POS x Set horizontal position of the PC source. x =0~60

42 R PC-H-POS Read horizontal position of PC source. 43 S PC-V-POS x Set vertical position of the PC source.

x =0~60 44 R PC-V-POS Read vertical position of PC source. 45 S PC-PHASE x Set PC source phase.

x =0~30 46 R PC-PHASE Read PC source phase. 47 S PC-CLOCK x Set PC source clock

x =700~230048 R PC-CLOCK Read PC source clock.

# Command Description49 S PC-WXGA-XGA x Set WXGA/XGA preference.

x =0, 1 0=WXGA 1=XGA

50 R PC-WXGA-XGA Read PC WXGA/XGA status. 51 S PC-RESET x Return to the default settings for the

PC source. x =0,1 0=Off 1=On

52 S MIXER x Set Mic mixer state. x =0, 1 0=Off 1=Mic

53 R MIXER Read mixer status.54 S MIC-VOL x Set microphone Volume.

x =0~10055 R MIC-VOL Read microphone volume.56 S DELAY x Set audio delay.

x =0~3 : 0=Off 1=40ms 2=110ms 3=150ms

57 R DELAY Read audio delay setting. 58 S MUTE x Set audio mute state.

x = 0,1 0=Unmute 1=Mute

59 R MUTE Read audio mute status. 60 S OUT-VOL x x = 0~100 61 R OUT-VOL Get volume of audio out.62 S HDMI1-AUDIO x Set HDMI 1 audio source.

x = 0~2 0=Automatic 1=Analog 2=Embedded

63 R HDMI1-AUDIO Read HDMI 1 audio source.



# Command Description64 S HDMI2-AUDIO x Set HDMI 2 audio source.


65 R HDMI2-AUDIO Read HDMI 2 audio source. 66 S DP-AUDIO x Set DisplayPort audio source.


67 R DP-AUDIO Read DisplayPort audio source.68 S HDMI1-VOL x Set HDMI 1 volume.

x =0~100 69 R HDMI1-VOL Read HDMI 1 audio volume. 70 S HDMI2-VOL x Set HDMI 2 volume.

x =0~10071 R HDMI2-VOL Read HDMI 2 audio volume. 72 S DP-VOL x Set DisplayPort volume.

x =0~10073 R DP-VOL Read DisplayPort audio volume. 74 S PC1-VOL x Set PC1 volume.

x =0~100 75 R PC1-VOL Read PC1 audio volume. 76 S PC2-VOL x Set PC2 volume.

x = 0~10077 R PC2-VOL Read PC2 audio volume. 78 S AUTO-SYNC-OFF x Set Auto Sync Off mode.

x = 0~2 0=Off 1=Fast 2=Slow

79 R AUTO-SYNC-OFF Read Auto Sync Off mode.80 S AUTO-INPUT x Set Auto-Input mode.

x = 0, 1 0=Off 1=Scan All

81 R AUTO-INPUT Read auto input mode. 82 S OSD-H-POS x Set OSD horizontal position.

x = 0~100 83 R OSD-H-POS Read OSD horizontal position.



# Command Description84 S OSD-V-POS x Set OSD vertical position.

x = 0~100 85 R OSD-V-POS Read OSD vertical position. 86 S OSD-TIMER x Set OSD automatic off time.

x =10~100 (seconds) 87 R OSD-TIMER Read OSD automatic off time. 88 S OSD-TRANS x Set OSD transparency.

x =0~100 89 R OSD-TRANS Read OSD transparency setting.90 S OSD-DISPLAY x Set OSD display mode.

x = 0~2 0=Off 1=Info 2=On

91 R OSD-DISPLAY Read OSD display status. 92 S IP-MODE x Set IP mode.

x = 0, 1 0=Static 1=DHCP

93 R IP-MODE Read IP mode. 94 S IP-ADDR x.x.x.x Set IP address.

x =000~255 Note: The IP address cannot be manually set when in DHCP mode.

95 R IP-ADDR Read the current IP address. 96 S GATE-WAY x.x.x.x Set gateway.

x =000~255 97 R GATE-WAY Read gateway. 98 S SUB-NET x.x.x.x Set subnet mask.

x =000~255 99 R SUB-NET Read subnet mask. 100 S UDP x Set UDP port.

x =1~65535 101 R UDP Read UDP port.102 R MAC-ADDR Read MAC address.103 S EDID-FROM x Set the EDID copy source.

x = 0~3 0=None 1=Out1 2=Out2 3=Default



# Command Description104 R EDID-FROM Read which output the EDID is set to

be copied from. 105 S EDID-TO x Set the EDID copy destination.

x = 0~3 0=None 1=HDMI1 2=HDMI2 3=DP

106 R EDID-TO Read the input the EDID will be copied to.

107 S EDID-COPY x Set Copy EDID mode. x = 0, 1 0=No 1=Yes

108 R EDID-COPY Read activity status of the EDID copy.

109 S MIC-VOL ++ Set increase microphone volume.110 S MIC-VOL -- Set decrease microphone volume.111 S OUT-VOL ++ Set increase out volume.112 S OUT-VOL -- Set decrease out volume.113 S HDMI1-VOL ++ Set increase HDMI1 volume.114 S HDMI1-VOL -- Set decrease HDMI1 volume.115 S HDMI2-VOL ++ Set increase HDMI2 volume.116 S HDMI2-VOL -- Set decrease HDMI2 volume.117 S DP-VOL ++ Set increase DP volume.118 S DP-VOL -- Set decrease DP volume.119 S PC1-VOL ++ Set increase PC1 volume.120 S PC1-VOL -- Set decrease PC1 volume.121 S PC2-VOL ++ Set increase PC1 volume.122 S PC2-VOL -- Set decrease PC2 volume.

Note: Commands will not be executed unless followed by a carriage return <CR>. Commands are not case-sensitive.

27 OSD MENU


All functions of this unit can be controlled by using the OSD (On Screen Display) which is activated by pressing the MENU button on the front of the unit. Use the + (Plus), − (Minus), ENTER, and MENU buttons to navigate the OSD menu. Press the “MENU” button to back out from any menu item and then press it again to close the menu.

MAIN MENU (1st LEVEL)

DISPLAY

PICTURE

AUDIO

MISCELLANY

FACTORY

INFOMATION

28 OSD MENU


The individual functions of the OSD will be introduced in the following section. Items marked in BOLD are the factory default settings.

1. Source: Provides control over the selection of the input video source to output.2. Size: Selects the aspect ratio to use when outputting the source. 3. HDCP on Input: Selects the HDCP logic to use with the HDMI1/HDMI2/DP input. 4. Resolution: Selects the output resolution to use. 5. Comp in PC: Provides control over the selection of component video support for

VGA inputs.

DISPLAY2nd LEVEL 3rd LEVEL 4th LEVELSOURCE HDMI 1

HDMI 2DP PC 1PC 2

SIZE OVER SCANFULLFOLLOW INPUTPAN SCANLETTER BOXUNDER 2UNDER 1

29 OSD MENU


DISPLAY2nd LEVEL 3rd LEVEL 4th LEVELRESOLUTION 640X480@60

800X600@601024X768@601280X768@601360X768@601280X720@601280X800@601280X1024@601440X900@601400X1050@601680X1050@601600X1200@601920X1080@601920X1200@60720x480p@601280x720p@601920x1080i@601920x1080p@60720x576p@501280x720p@501920x1080i@501920x1080p@50NATIVE OUT 1NATIVE OUT 2

HDCP ON INPUT HDMI 1 ONOFF

HDMI 2 ONOFF

DP ONOFF

COMP IN PC COMP IN PC 1 ONOFF

COMP IN PC 2 ONOFF

30 OSD MENU


PICTURE2nd LEVEL 3rd LEVEL 4th LEVELCONTRAST 0~60 (30)BRIGHTNESS 0~60 (30)RED 0~1023 (512)GREEN 0~1023 (512)BLUE 0~1023 (512)HUE* 0~60 (30)SATURATION* 0~60 (30)SHARPNESS* 0~30 (10)NOISE REDUCTION* OFF

LOWMIDDLEHIGH

FINETUNE** AUTO ADJUST NO/YESH-POSITION 0~60 (30)V-POSITION 0~60 (30)PHASE 0~30 (16)CLOCK 700~2300 (1344)WXGA/XGA WXGA

XGARESET NO/YES

Note: Commands with one asterisk (*) are only available for HDMI and DisplayPort inputs. Commands with two asterisks (**) are only available for PC inputs.

1. Contrast: Provides control over the overall contrast of the scaled output image.2. Brightness: Provides control over the overall brightness of the scaled output

image.3. Red/Green/Blue: Provides control over the red, green, and blue color level of the

scaled output.4. Hue: Provides control over the hue shift of the scaled output image.5. Saturation: Provides control over the color saturation level of the scaled output im

age.6. Sharpness: Provides control over the amount of sharpness processing to apply to

the scaled output image.7. Noise Reduction: Provides control over the digital noise reduction processing when

applied to the scaled output image.8. Finetune: Provides control over video configuration of PC1/PC2 source.

31 OSD MENU


1. Mixer: Provides control over the mic mixer state.2. Mic Volume: Provides control over the microphone volume.3. Delay: Provides control over the audio delay.4. Mute: Provides control over the audio mute state.5. Output Volume: Provides control over the video output volume. 6. Embedded Audio: Provides control over the selection of the audio source to output. 7. Input Volume: Provides control over the input video source volume.

AUDIO2nd LEVEL 3rd LEVEL 4th LEVELMIXER OFF

MICMIC VOLUME 0~100 (70)DELAY OFF

40ms110ms150ms

MUTE OFFON

OUTPUT VOLUME 0~100 (80)EMBEDDED AUDIO HDMI1 AUTOMATIC

EMBEDDEDANALOG

HDMI2 AUTOMATICEMBEDDEDANALOG

DP AUTOMATICEMBEDDEDANALOG

INPUT VOLUME HDMI1 0~100 (100)HDMI2 0~100 (100)DP 0~100 (100)PC1 0~100 (100)PC2 0~100 (100)

32 OSD MENU


1. Auto Input: Sets the auto detection of the input video source.2. Auto Sync Off: Sets the amount of time to continue outputting sync

with the free run color if there is no live source and no operations have been executed on the unit. Setting this feature to “OFF” forces the unit to always output sync.

3. OSD: Provides control over the OSD configuration.4. Ethernet: Provides control over the IP configuration and control port.

FACTORY2nd LEVEL 3rd LEVELRESET NO/YESUPDATE SYSTEM USB UPDATE

MISCELLANY2nd LEVEL 3rd LEVEL 4th LEVELAUTO INPUT OFF

SCAN ALLAUTO SYNC OFF OFF

FAST [10sec]SLOW [120sec]

OSD H POSITION 1~100 (50)V POSITION 1~100 (50)TIMER 10~100sec (100)TRANSPARENCY 1~100 (50)DISPLAY INFO

ONOFF

ETHERNET IP MODE STATICDHCP

IP ADDRESS 0~255SUBNET 0~255GATEWAY 0~255CONTROL PORT 1~65535 (50000)MAC ADDRESS [MAC Address]

33 OSD MENU


5. EDID Setup: Select the EDID to use with the HDMI1/HDMI2/DP input. Selecting “Output” will copy and use the current sink’s EDID but will not re-copy the EDID if the sink is changed. Selecting “Auto Output” will automatically copy and use the EDID from the current sink every time a new sink is connected.

EDID SETUP EDID FROM NONEOUT1OUT2DEFAULT

EDID TO NONEHDMI1HDMI2DP

EDID COPY NO/YESNote: The default IP address is 192.168.1.254.

34 OSD MENU


1. Reset All: Selecting this option will reset the unit’s settings back to their factory defaults.

2. Update from USB: Provides a way to update the unit’s firmware. In-sert a USB thumb drive, with a valid firmware file (*.bin format) in the root directory, into the unit’s USB service port then select this option. After the update is complete the unit will automatically reboot.

INFORMATION2nd LEVEL 3rd LEVELINPUT RESOLUTION

[Current Status Details]

INPUT HDCPOUTPUT RESOLUTIONOUTPUT1 HDCPOUTPUT2 HDCPIP ADDRESSVERSION

Information: This screen displays information about the unit’s current state, input and output status, as well as the current IP address and firmware version.

35 SPECIFICATIONS


PHYSICAL

Dimensions 8.62”(W) x 6.14”(D) x 1.7”(H) Power Rating +24V DC, 1A (Max.) Operating Temperature 0 to 40ºC, operatingHumidity 20 to 90% RH, Non-Condensing

CERTIFICATIONS

CE, FCC

GREEN COMPLIANCE

RoHS

ORDER INFORMATIONLBC-PSW52 Link Bridge ™ 5x2 Multi-Format

Presentation Scaling Switch

Included Accessories 24 VDC, 1A Power Supply

Remote ControlRELATED PRODUCTS

LBC-PSW84 Link Bridge ™ 8x4 Multi-Format Presentation Scaling Switch

PANEL DRAWING

VIDEO SPECIFICATIONSResolution Up to 1080p or 1920x1200@60Hz

Input Connectors 2- HDMI Female Plug2- HD-15 VGA Female*1- DisplayPort

Output Connectors 1- HDMI Female Plug1- HDBaseT RJ45

Protocol DDC/EDID/HDCP Capable

*VGA input does not support YPbPr video format

AUDIOInput Channel Capacity 1- microphone

3- L/R analog

Input Connectors 6.35mm microphone jack3.5mm (L/R) analog stereo jack

Output Channel Capacity 1- L/R Analog

Output Connectors 3mm stereo jack

CONTROL DATALAN/Telnet 1- RJ-45

RS-232 1- 3.5mm stereo jack

IR 2- 3mm jackOthers Input control, terminal block

LOCK+

-ENTER

MENU

SELECT

HDMI1

DPHDMI2

1PC

2PC LOCK


LINE OUT


INPUT CONTROL

C 1 2 3 4 5

CONTROL

OFF

ON

PHANTOM

PC 2PC 1DC 24V

PC 2

36 MAINTENANCE AND TROUBLESHOOTING


3.1 MaintenanceThere is no operator maintenance other then keeping the units clean. However, observe the following light indicators to make sure that the unit is working properly:

3.2 TroubleshootingIf the LBC-PSW52 units do not operate properly after installation, check for possible cable breaks, loose connections, and incorrect cable connections. If problems persist that may be fiber related, contact BCI at 1-800-214-0222 for furtherassistance.

For electrical problems, perform the following troubleshooting procedures:

1. If the POWER indicator is OFF, check for the following: a. The line cord is plugged into the unit and your outlet has power.

2. If the POWER indicator is ON, but the Link indicator is OFF, check for the following: a. Make sure the appropriate cables are being used. b. Cable and cable connectors are not broken. c. For each unit, the transmit (TX) cable is connected to the other unit’s receiver (RX).

3. If the POWER indicator and Link indicator are ON, but the channels are not operating, then: a. Check to see that the attached user equipment is turned on. b. Both ends of the link are connected to the corresponding equipment and to the same corresponding channel port. c. Cable connections at both channels are securely fastened to each connector. Turn the power off, then back on to reset the link.

37 SERVICE PROCEDURE


5.1 Replacement Policy

Standard products found defective on arrival (DOA) will be replaced, based on availability, within 24 to 48 hours anywhere in the U.S. Please call Customer Service at 800-214-0222 for information.

5.2 Return/Repair Service

The LBC-PSW52 contains no user serviceable components. If you have a problem with your unit, please contact the Customer Service Department. To facilitate our return/ repair processing please contact Broadata Communications, Inc. to obtain a Return Material Authorization (RMA). Please include the following information:

• Product Model Number• Serial Number• Complete Description of Problem• Hardware Installation Description

Broadata Communications, Inc.2545 West 237th Street, Suite K

Torrance, CA 905051-800-214-0222(310) 530-1416

(310) 530-5958 (Facsimile)e-mail: [email protected]

Website: www.broadatacom.com

38 LIMITED WARRANTY


6.0 LIMITED WARRANTY

Broadata Communications, Inc. (BCI) warrants, for a period of one year from date of ship-ment, each product sold shall be free from defects in material and workmanship. BCI will correct, either by repair, or at BCI’s election, by replacement, any said products that in our sole discretion prove to be defective and are returned to the manufacturing location within 30 days after such defect is ascertained. All warranties are limited to defects arising under normal use and do not include malfunctions or failure resulting from misuse, abuse, neglect, alterations, electrical power problems, usage not in accordance with product instructions, improper installation, or damage determined by BCI to have been caused by the Buyer or repair made by a third party. Limited warranties granted on products are to the initial customer end-user and are not transferable. OUR LIABILITY UNDER THIS WARRANTY SHALL IN ANY CASE BE LIMITED TO THE INVOICE VALUE OF THE PRODUCT SOLD AND BCI SHALL NOT BE LIABLE TOANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAM-AGES ARISING FROM THE USE OF ITS PRODUCTS OR THE SALE THEREOF. We make NO WARRANTY AS TO THE MERCHANTABILITY OF ANY GOODS, OR THAT THEY ARE FIT FOR ANY PARTICULAR PURPOSE OR END APPLICATION NOR DO WE MAKE ANY WARRANTY, EXPRESSED OR IMPLIED OTHER THAN AS STATED ABOVE.


Broadata Communications, Inc.2545 West 237th Street, Suite K

Torrance, CA 905051-800-214-0222(310) 530-1416

(310) 530-5958 (Facsimile)e-mail: [email protected]: www.broadatacom.com2545 West 237th Street

Torrance, CA 90505

800•214•0222310•530•1416

e-mail: [email protected]

LINKBRIDGE™ PRESENTATION SCALING SWITCH with 5 Inputs … · The LinkBridge™ HDBaseT...

Documents

Transcript of LINKBRIDGE™ PRESENTATION SCALING SWITCH with 5 Inputs … · The LinkBridge™ HDBaseT...