LIGHTPLANE 3.5 Suspended (LP3.5S) - Install Guide · Carefully remove lens using suction cup or...

A 1035 22nd Avenue, Unit 1 n Oakland, CA 94606 P 510.489.2530 E [email protected] W alwusa.com

INSTALLATION INSTRUCTIONS

LIGHTPLANE 3.5LP3.5 | Suspended | LED

LP3.5 Suspended Installation Guide 2 of 12 102-000024 - IG121818-A.0

Safety & Warnings!1. Read all instructions.2. Install in accordance with national and local electrical code regulations.3. This product is intended to be installed and serviced by a qualified, licensed electrician.4. Turn off electrical power before installing or servicing fixture in any way.5. Do not install in wet locations. For dry and damp use only.6. Turn off electrical power before installing or servicing fixture in any way.7. To reduce the risk of fire and overheating, make sure all connections are tight.8. This product is suitable for continuous row mounting.

1. Lisez toutes les instructions.2. Installez conformément à la réglementation du code électrique national et local.3. Ce produit est destiné à être installé et entretenu par un électricien agréé qualifié.4. Coupez l’alimentation électrique avant d’installer ou de réparer le luminaire de quelque manière que

ce soit.5. Ne pas installer à l’extérieur ou dans des endroits humides. Pour une utilisation en intérieur et sec

seulement.6. Coupez l’alimentation électrique avant de évoluer le système d’éclairage en aucune façon.7. Pour réduire le risque d’incendie et de surchauffe, assurez-vous que toutes les connexions sont bien

serrées.8. Ce produit convient au montage en ligne continue.

Attention!

SHOCK HAZARD! May result in serious injury or death. Turn power OFF at circuit breaker prior to installation or servicing.

LP3.5 Suspended Installation Guide LP3.5 Suspended Installation Guide 3 of 12 102-000024 - IG121818-A.0

Table of Contents

Troubleshooting 10

Wiring Diagrams 11

Installation 5Prepare Ceiling 5Standard Suspension 5

Connecting Multiple Sections 7

Luminaire Overview 4Diagrams 4Components 4Parts (by others) 4Tools Required 4Quick Specs 4


LUMINAIRE OVERVIEW

Drill#2 phillips bit

Tools Required

Wire strippers

Input Voltage / Frequency:See product label

Rated Power:See product drawing

Ambient Temperature:-4° – 120°F (-20° – 50°C)Environment:Dry and damp locations

Quick SpecsParts (by others)

STANDARD SUSPENSION COMPONENTS

Suspension BulletCanopy Assembly Suspension Cable Ceiling Fitting

J-Box

Ceiling Fitting / Suspension Bullet

To Building Power

Canopy

Power Cord

Suspension Cables

Cable Gripper

Fixture BodyIntegrated LED Driver

4” Square or Octagonal Junction Box

Wood Screws, #10, 1.5” long 1/8” Hex Key (for Joining)

5mm Hex Key (for Joining)

LP3.5 Suspended Installation Guide 5 of 12 102-000024 - IG121818-A.0LP3.5 Suspended Installation Guide

Ceiling Fittings may also be mounted using toggle bolts.

3B Install Ceiling Fitting - Toggle Bolts

Ceiling Fittings may also be mounted on 1/4”-20 Threaded Rods.

3C Install Ceiling Fitting - 1/4”-20 Threaded Rods

Installation: Prepare Ceiling Installation: Standard Suspension

Ceiling Fittings may be installed directly into framing with appropriate hardware.

3A Install Ceiling Fitting - Framing

CL

ELECTRICAL WIRING:CHECK FOR

A

T

MUST

See final/record drawings for mounting locations. Install framing or strut channels with consideration for alignment of wiring and suspension mounting locations.

1 See Final/Record Drawings for Mounting Locations

SAMPLE DRAWING

CL

ELECTRICAL WIRING:CHECK FOR

A

T

MUST

Install 4” square or octagonal Canopy J-Box (sold separately) at power feed location per final/record drawing.

2 Install Canopy J-Box

SAMPLE

DRAWIN

G


! DO NOT PINCH OR PUT EXCESSIVE TENSION ON WIRES while joining sections or reattaching heatsink.


Bring wiring and canopy assembly to J-box. Refer to page 11 and final/record drawing to make wiring connections. CAUTION: High Voltage Wire — Ensure Power is OFF prior to connecting wiring.

9 Connect High Voltage Wiring

Route Suspension Cable through Suspension Bullet. Ball end should sit in Suspension Bullet. Screw Suspension Bullet to Ceiling Fitting.

4 Route Suspension Cable and Attach to Ceiling

Installation: Standard Suspension(Cont.)

6"

Use wire snips or shears to cut Suspension Cables to desired length. Keep an extra 6 inches of cable for adjustments.

5 Cut Suspension Cables to Desired Length 8 Adjust Suspension Cable LengthAdjust fixture until it is level and at desired height. Depress top of Cable Gripper to lower fixture. Keep fixture supported while lowering. Cut excess cable.

Raise fixture to Suspension Cables, and attach fixture by inserting Suspension Cable through Cable Grippers.

7 Raise Fixture to Suspension Cables

6 Connecting Multiple Sections (If Necessary)Please see steps 12 through 25 for directions on connecting multiple sections.



Installation: Standard Suspension (Cont.)

Turn breaker ON and check if fixture operates as intended and that there are no loose connections.

11 Turn Power On

Installation: Connecting Multiple Sections

Remove heatsink/reflector screws that attach to housing. Set aside.

13 Remove Heatsink/Reflector Screws

Remove heatsink/reflector and hang over side of fixture. CAUTION: Do not apply excessive tension to wires!

14 Remove Heatsink/Reflector

Carefully remove lens using suction cup or similar.

12 Remove Lens

Mount Canopy Bracket to J-Box using provided screws, then secure Canopy over J-Box with finial. Attach bullet (with cable) to canopy. CAUTION: Do not pinch wire connections.

10B Combo Canopy Installation

! DO NOT PINCH OR PUT EXCESSIVE TENSION ON WIRES while installing canopy.

Mount Canopy Bracket to J-Box using provided screws, then secure Canopy over J-Box with finial. CAUTION: Do not pinch wire connections.

10A Mount Canopy Bracket to J-Box & Secure Canopy

! DO NOT PINCH OR PUT EXCESSIVE TENSION ON WIRES while installing canopy.


Connect wiring quick-connects between sections. Match each color, as shown. NOTE: Color combinations may vary.

20 Connect Wiring Between Sections

Installation: Connecting Multiple Sections (Cont.)

Join sections together, as shown, ensuring correct alignment. See final/record drawing for more details. CAUTION: Do not pinch wires while joining!

15 Align and Join Sections TogetherTighten set screws to secure outer corner bracket to joined section using a 1/8” hex key. Ensure each section is properly aligned and that there are no gaps between sections.

18 Tighten Set Screws on Outer Corner

Tighten joiner screws, as shown, using a 5mm hex key. Ensure each section is properly aligned, and that there are no gaps between sections.

19 Tighten Joiner Screws on Inner CornerTighten joiner screws, as shown, using a 5mm hex key. Ensure each section is properly aligned, and that there are no gaps between sections.

16 Tighten Joiner Screws

17 Mitered Corners: Join SectionsJoin sections together, as shown, ensuring correct alignment. See final/record drawing for more details. CAUTION: Do not pinch wires while joining!


Installation: Connecting Multiple Sections (Cont.)

Re-install heatsink/reflector screws to attach back to housing.

22 Re-install Heatsink/Reflector Screws

Install Diffuser Shim at each joined location to prevent light leak between lens sections. Re-install at endcap locations, as necessary.

23 Install Diffuser Shim

Re-install each heatsink/reflector section. CAUTION: Do not pinch wires while reattaching!

21 Re-install Heatsink/ReflectorCarefully re-install lens, ensuring lens sits properly within Lens Clips.

24 Re-install Lens

Ensure the lens is properly installed between the Lens Clips.

25 Ensure Lens Sits Properly Between Lens Clips


! DO NOT PINCH OR PUT EXCESSIVE TENSION ON WIRES while joining sections or reattaching heatsink.


Troubleshooting

Full Fixture does not illuminate • Ensure all wire connections are made.• Ensure fixture is wired correctly and power is on. • Check that circuit breaker is on and not off or tripped.• LED driver may be defective.

Full fixture is flickering • 0-10V, DMX, and DALI Dimming Models: Ensure polarity is correct for DATA + and - connections. Swapping DATA + and - connections can cause flickering.

• TRIAC Dimming Models: Ensure a compatible TRIAC Forward Phase dimmer is connected to fixture. Call tech support for further information.

• Possible loose DATA + and - connections from fixture to 0-10V, DMX, or DALI control.

• Possible loose low voltage DC + or - connection from driver to LED. Call customer support.

Only a certified electrician can service and troubleshoot product field issues. Always turn main power off before servicing fixture.

Fixture section(s) do not illuminate

• Possible loose low voltage DC + or - connection between LED boards or from LED driver to LED boards.

• Some fixtures contain multiple LED drivers. In this case, it’s possible one of the drivers is defective, which will cause the LED connected to the driver not to illuminate. Call tech support.

Fixture section(s) are flickering • Possible loose low voltage DC + or - connection between LED boards.

Fixture does not dim • 0-10V, DMX, and DALI Dimming Models: Ensure polarity is correct for DATA + and - connections. Swapping DATA + and - connections can cause flickering. TEST.

• TRIAC Dimming Models: Ensure a compatible TRIAC Forward Phase dimmer is connected to fixture. Call tech support for further information.

• Possible loose DATA + and - connections from fixture to 0-10V, DMX, or DALI control.


Wiring Diagrams

BlackWhite GreenGround

Line Voltage (Hot)

Line Voltage (Neutral)

L

NAC 50/60Hz

Traditional On/Off

BlackWhite Green

GreyPurple

Line Voltage (Hot)


Ground

0-10VDC (Dim-)

0-10VDC (Dim+)

L

NAC 50/60Hz

DIM-

DIM+

0-10V Dimming

BlackWhite Green

ClearBlack

DMX in shield

DMX in -

Line Voltage (Hot)


Ground

L

NAC 50/60Hz

DMX In Shield

DMX in -

RedDMX in +DMX in +

ClearBlack

DMX out shield

DMX out -

WhiteDMX out +

DMX Out Shield

DMX out -

DMX out +

DMX

Canopy/Power Feed

Canopy/Power Feed

Canopy/Power Feed


Wiring Diagrams (Cont.)

BlackWhite Green

PurpleGrey

Line Voltage (Hot)


Ground

Data +

Data -

L

NAC 50/60Hz

DATA +

DATA -

DALI

BlackWhite Green

PurpleGrey

Line Voltage (Hot)


Ground

E1

E2

L

NAC 50/60Hz

E1

E2

Lutron LDE

Canopy/Power Feed

Canopy/Power Feed

LIGHTPLANE 3.5 Suspended (LP3.5S) - Install Guide · Carefully remove lens using suction cup or...

Documents

Transcript of LIGHTPLANE 3.5 Suspended (LP3.5S) - Install Guide · Carefully remove lens using suction cup or...